砂轮专用英文对照

合集下载

砂轮专用英文对照

砂轮专用英文对照

此词汇适合外贸人员开展业务、技术人员查阅文献、生产人员、磨削、磨床人员生产中查阅对照。

abrasive 磨料abrasive grain 磨粒angle of repose 安息角artificial abrasive 人造磨料black fused alumina 黑刚玉black silicon carbide 黑碳化硅boron carbide 碳化硼brown fused alumina 棕刚玉bulk density 堆积密度capillarity 毛细现象combination grain size 混合粒度compressive strength 抗压强度conventional abrasive 普通磨料cubic boron nitride 立方氮化硼cubic silicon carbide 立方碳化硅diamond 金刚石emery 天然金刚砂fused alumina 电熔刚玉garnet 石榴石grain size 粒度grain size distribution 粒度组成green silicon carbide 绿碳化硅grit designation 粒度号impact toughness 冲击韧性losse grain 自由磨粒macrograins 粗磨粒magnetic material 磁性物metal clad diamond 金属衣金刚石microcrystalline fused alumina 微晶刚玉microgrits 微粉monocrystalline fused alumina 单晶刚玉natural abrasive 天然磨料natural corundum 天然刚玉natural diamond 天然金刚石physical corundum 物理刚玉pink fused alumina 絡刚玉(粉刚玉)polycrystal 多晶体polycrystalline cubic boron nitride 立方氮化硼烧结体polycrystalline diamond 人造金刚石烧结体silicon carbide 碳化硅single crystal 单晶体sintered alumina 烧结刚玉specific surface area 比表面积super abrasive 超硬材料synthetic diamond 人造金刚石white fused alumina 白刚玉zirconia alumina 锆刚玉abrasive belts 砂带abrasive cloth 砂布abrasive cloth belts 布砂带abrasive cloth in rolls 卷状砂布abrasive cloth in sheets 页状砂布abrasive discs 砂盘abrasive paper 砂纸abrasive paper belts 纸砂带abrasive paper in rolls 卷状砂纸abrasive paper in sheets 页状砂纸abrasive products 磨具abrasive sleeves 砂套adhesive 粘结剂aluminium oxide sintered stick 烧结刚玉魔石aluminium oxide sintered wheel 烧结刚玉砂轮backing 基材balancing test 平衡试验tbond 结合剂bonded abrasive products 固结磨具brick’s stick 磨石butt joint belts 对接砂带centreless grinding wheel 无心磨砂轮centreless regulating wheel 无心磨导轮closed coat 密植砂closed pore 闭口气孔closed porosity 闭口气孔率closed backing 布基coated abrasives 涂附磨具combination backing 复合基combination backing abrasive belts 复合基砂带combination stone 双面磨石concentration 浓度cubic boron nitride abrasive products 立方氮化硼磨具cubic boron nitride grinding wheel 立方氮化硼砂轮CBN section 立方氮化硼层cutting off wheel 切断砂轮cylindrical abrasive sleeves 筒形砂套cylinder wheel 筒形砂轮deep cut and creep feed grinding wheel; 深切缓进给砂轮density of coating grain 植砂密度depressed center wheel 钹形砂轮diamond abrasive products 金刚石磨具diamond beads 金刚石串珠diamond circular saw blades 金刚石圆锯片diamond cut-off wheel 金刚石切割砂轮diamond edging wheel 金刚石磨边砂轮diamond dressing roller 金刚石滚轮diamond cylinderi wheel 金刚石筒形砂轮diamond finishing pellets 金刚石精磨片diamond frame saw blades 金刚石框架锯条diamond grinding wheel 金刚石砂轮diamond section 金刚石石层diamond saw segments 锯齿diamond sawing and cutting tool 金刚石锯切工具diamond wire saw 金刚石绳锯diluent 稀释剂dish wheel 蝶形砂轮dispersing agent 分散剂dulling 钝化dynamic balance test 动平衡试验electroplated diamond inner slicing disc 电镀金刚石内圆切割锯片electroplated diamond files 电镀金刚石什锦锉electroplated metal bond 电镀金属结合剂electroplated super abrasive products 电镀超硬磨料磨具endless abrasive belts 无接头砂带fibre backing 钢纸基flap wheels 研磨页轮flap wheels with flange 卡盘研磨叶轮flap wheels with shaft 带轴研磨叶轮form grinding wheel 成型砂轮fused bond 烧熔结合剂glue bond 动物胶粘结剂grade 硬度grinding segments 砂瓦grinding wheel 砂轮grinding wheel for rice husking 碾米砂轮grinding wheel steel balls 磨钢球砂轮grinding wheel peripheral speed (砂轮)工作速度grindstone 天然磨石high-pressure snagging wheel 重负荷修磨砂轮high-speed grinding wheel 高速砂轮honing stick 衍磨条hubbed wheel 单面凸砂轮inorganic bond 无机结合剂intermediate section 过渡层joint abrasive belts 接头砂带lap joint belts 搭接砂带lapping compound 研磨剂lapping paste 研磨膏liquid lapping compound 研磨液magnesia bond 菱苦土结合剂magnesia grindstone菱苦土磨石maximum operating speed 砂轮最高工作速度metal bond 金属结合剂metallographic abrasive paper 金相砂纸mounted cone, curved side 椭圆磨头mounted plug, flat end 圆柱磨头mounted plug, round end 半球形磨头mounted wheel 磨头oil soluble lapping paste 油溶性研磨膏open coat 疏植砂open pore 开口气孔open porosity 开口气孔率organic bond 有机结合剂paper backing 纸基percentage of grain 磨粒率pore 气孔pressure sensitive backing discs 粘贴砂盘pulp segment 纸浆磨块pulp stone 纸浆磨石PV A (polyvinylalcohol) grinding wheel PV A 砂轮resinoid bond 树脂结合剂resin over glue bond 半树脂粘结剂resin over resin bond 全树脂粘结剂revolving strength 回转强度rotation test 回转试验rubber bond 橡胶结合剂self-sharpening 自锐性shellac bond 虫胶结合剂sintered bond 烧结结合剂sintering metal bond 烧结金属结合剂solid lapping compound 固体研磨剂special purpose wheels 专用砂轮static balance test 静平衡试验straight cup wheel 杯形砂轮straight wheel 平形砂轮structure 组织substrate 基体super abrasive section 超硬磨料层super abrasive products 超硬磨料磨具super finishing stick 超精油石support 载体taper cup wheel 碗形砂轮tapered wheel 斜边砂轮thin grinding wheel 薄片砂轮threaded insert disk 螺栓紧固平形砂轮total porosity 总气孔率true density 真密度truncated cone abrasive sleeves 截锥砂套tumbling chip abrasives 滚抛磨块unbalance 不平衡unbalance 不平衡量unbalance value 不平衡值vitrified bond 陶瓷结合剂volume density 体积密度water absorption 吸水率waterproof abrasive cloth 耐水砂布waterproof abrasive cloth belts 耐水布砂带waterproof abrasive paper 耐水砂纸waterproof abrasive paper belts 耐水纸砂带waterproof bond 耐水粘结剂water soluble lapping paste 水溶性研磨膏wheel relieved and recessed both side 双面凹带锥砂轮wheel relieved and recessed same side 单面凹带锥砂轮wheel recessed one side 单面凹砂轮wheel recessed two side 双面凹砂轮worm grinding wheel 蜗杆砂轮。

(完整版)机床用语中英文对照

(完整版)机床用语中英文对照

Aabrasion n. 磨料,研磨材料,磨蚀剂, a. 磨损的,磨蚀的abrasive belt n. 砂带abrasive belt grinding n. 砂带磨削,用研磨带磨光abrasive cut-off machine n. 砂轮切断机abrasive dressing wheel n. 砂轮修整轮abrasive grain n. 磨料粒度abrasive grit n. 研磨用磨料,铁粒abrasive lapping wheel n. 磨料研磨轮accuracy of position n. 位置精度accuracy to shape n. 形状精度active cutting edge n. 主切削刃adapter flange n. 连接器法兰盘adjointing flanks n. 共轭齿廓align n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准angle milling cutter n. 角铣刀angular grinding n. 斜面磨削,斜磨法angular milling n. 斜面铣削angular plunge grinding n. 斜向切入磨削angular turning n. 斜面车削arbour n. 刀杆,心轴,柄轴,轴,辊轴attachment n. 附件,附件机构,联结,固接,联结法automatic bar machine n. 棒料自动车床automatic boring machine n. 自动镗床automatic copying lathe n. 自动仿形车床automatic double-head milling machine n. 自动双轴铣床automatic lathe n. 自动车床automatic turret lathe n. 自动转塔车床Bbelt grinding machine n. 砂带磨床bench lathe n. 台式车床bevel n. 斜角,斜面,倾斜,斜切,斜角规,万能角尺,圆锥的,倾斜的,斜边,伞齿轮,锥齿轮bevel gear cutting machine n. 锥齿轮切削机床bevel gear tooth system n. 锥齿轮系,锥齿轮传动系统borehole n. 镗孔,镗出的孔,钻眼boring n. 镗孔,钻孔,穿孔boring fixture n. 镗孔夹具boring machine n. 镗床boring tool n. 镗刀boring, drilling and milling machine n. 镗铣床broaching machine n.拉床,铰孔机,剥孔机broaching tool n. 拉刀broad finishing tool n. 宽刃精切刀,宽刃精车刀,宽刃光切刀CCalibrate vt. 校准〔正〕,刻度,分度,检查〔验〕,定标,标定,使标准化,使符合标准cam contour grinder n. 凸轮仿形磨床carbide tip n. 硬质合金刀片carbide turning tool n. 硬质合金车刀carbide-tipped tool n. 硬质合金刀具cast iron machining n. 铸铁加工,铸铁切削加工centerless cylindrical grinder n. 无心外圆磨床ceramic cutting tool n. 金属陶瓷刀具chamfer n.;vt. 倒角,倒棱chamfered cutting edge n. 倒角刀刃champ v. 焦急champing fixture n. 快换夹具champing jaw n. 快换卡爪chaser n. 螺纹梳刀,梳刀盘,板牙chatter vi.;n. 振动,振荡,震颤,刀振cherry n.;a. 樱桃,鲜红的,樱桃木制的chip n. 切屑,铁屑,刀片,刀头,片,薄片,芯片,基片chip breaker groove radius n. 断屑槽底半径,卷屑槽底半径chip clearance n. 切屑间隙chip cross-sectional area n. 切屑横截面面积chip curl n. 螺旋形切屑chip flow n. 切屑流chip formation n. 切屑形成chip removing process n. 去毛刺加工chip variable n. 切屑变量chuck n. 卡盘,夹盘,卡头,〔电磁〕吸盘,vt. 固定,装卡,夹紧,卡住chucker n. 卡盘车床,卡角车床circular drillling machine n. 圆工作台钻床circular path n. 环路,圆轨迹circular pitch measurement n. 周节测量circumference n. 圆周,周线,周界,周围,四周,范围close-grained a. 细颗粒的coeffecient of tool thrust n. 刀具推力系数coil chip n. 卷状切屑cold circular saw n. 冷圆锯cold saw n. 冷锯column drilling machine n. 圆〔方〕柱立式钻床combined drill and milling cutter n. 复合钻铣床complete traverse grinding n. 横进给磨削,切入磨削computer-controlled machine n. 计算机控制机床,数控机床contact pattern n. 靠模continuous chip n. 连续切屑continuous spiral chip n. 连续螺旋切屑contour n. 轮廓,外形,外貌,轮廓线,回路,网路,电路,等高线,等值线,轮廓等高距a. 仿形的,靠模的contour grinding n. 仿形磨削,成形磨削contour milling n. 成形铣削,外形铣削,等高走刀曲面仿形法convex milling attachment n. 凸面铣削附件convex turning attachment n. 中凸车削附件,凸面车削附件coolant lubricant n. 冷却润滑剂coolant lubricant emulsion n. 冷却润滑乳液〔剂〕copy n. 样板,仿形,靠模工作法,拷贝复制品,v. 复制,模仿,抄录copy grinding n. 仿形磨床copy-mill n. 仿形铣copying turret lathe n. 仿形转塔车床corner n. 角,弯〔管〕头,弯管counterbore n. 埋头孔,沉孔,锥口孔,平底扩孔钻,平底锪钻, n.;vt. 扩孔,锪孔,镗孔,镗阶梯孔crankshaft grinding machine n. 曲轴磨床crankshaft turning lathe n. 曲轴车床creep feed grinding n. 缓进给磨削cross milling n. 横向铣削curly chip n. 卷状切屑,螺旋形切屑,切屑螺旋cut v.;n. 切削〔割〕,口,片,断,断开,削减,减少,断面,剖面,相交,凹槽cut off n. 切断〔开,去〕,关闭,停车,停止,断开装置,断流器,挡板,截止,截流cut teeeth n. 铣齿cut-off grinding n. 砂轮截断,砂轮切割cutter n. 刀具,切削工具,截断器,切断器,切断机cutting n. 切削,切片,切割,切屑,金属屑,截槽cutting edge profile n. 切削刃轮廓〔外形,断面〕,切削刃角度cutting force n. 切削力cutting lip n. 切削刃,刀刃,钻唇,钻刃cutting operation n. 切削加工,切削操作,切削作业cutting rate n. 切削效率,切削速率cutting tool n. 刀具,切削工具,刃具cycle n. 周期,周,循环,一个操作过程,轮转,自行车cylindrical grinder n. 外圆磨床Ddamage n.;vt. 损坏〔害,伤,耗,失〕,破坏,事故,故障,伤害,危害deep-hole drilling n.深孔钻削deep-hole milling n. 深孔铣削design n. 设计,计算,计划,方案,设计书,图纸die-sinking n. 凹模dimension n. 尺寸,尺度,维度,量纲,因次direction of the feed motion n. 进给方向,进刀方向discontinuous chip n. 间断切屑distance n. 距离,间隔〔隙〕,长度,vt. 隔开double-column planer-miller n. 双柱龙门铣床dress v. 修饰,修整,平整,整理,清理,装饰,调制,准备,打磨,磨光,压平,轿直,清洗,清理,分级drilling n. 钻头,钻床,穿孔器,凿岩机,v. 钻孔,打孔,钻井,钻探drilling machine n. 钻床,钻机,钻孔机,打眼机drilling tool n. 钻孔〔削,井,眼〕工具Eedge point n. 刀口,刀刃efficiency n. 效率,效能,性能,功率,产量,实力,经济性,有〔功,实〕效end mill n. 立铣刀external grinding n. 外圆磨削Fface n. 表面,外观,工作面,表盘,屏,幕v. 面向,朝向,表面加工,把表面弄平face grinding machine n. 平面磨床face milling machine n. 端面磨床feed force n. 进给力feed motion n. 进给运动fine adjustment n. 精调,细调,微调fine boring n. 精密镗孔finish v.;n. 精加工,抛光,修整,表面粗糙度,完工,最后加工,最后阶段,涂层,涂料finish-cutting n. 精加工,最终切削fixture n. 夹具,夹紧装置,配件,零件,定位器,支架form n. 型式,类型,摸板,模型,形成,产生,成形,表格v. 形〔组,构〕成,产生,作出,成形,造型form-turn n. 成形车削free-cutting n. 自由切削,无支承切削,高速切削Ggap n. 间隔,间隙,距离,范围,区间,缺口,开口火花隙,vt. 使产生裂缝vi. 豁开gear cutting machine n. 齿轮加工机床,切齿机gear generating grinder n. 磨齿机gear hob n. 齿轮滚刀grinding cutter n. 磨具grinding force n. 磨削力grinding machine n. 磨床grinding wheel diameter n. 砂轮直径grinding wheel width n. 砂轮宽度groove n. 槽,切口,排屑槽,空心槽,坡口,vt. 切〔开,铣〕槽groove milling n.铣槽Hheadstock spindle n. 床头箱主轴,主轴箱主轴,头架轴helical tooth system n. 螺旋齿轮传动装置high precision lathe n. 高精度车床high-speed n. 高速high-speed machining n. 高速加工hob n. 齿轮滚刀,滚刀,螺旋铣刀,v. 滚铣,滚齿,滚削horsepower n. 马力hobbing machine n. 滚齿机,螺旋铣床,挤压制模压力机,反应阴模机hole n. 孔,洞,坑,槽,空穴,孔道,管道,v. 钻〔穿,冲,开〕孔,打洞hone n. vt. 磨石,油石,珩磨头,磨孔器,珩磨,honing machine n. 珩磨机,珩床,搪磨床,磨孔机,磨气缸机Iinclination n. 倾斜,斜度,倾角,斜角〔坡〕,弯曲,偏〔差,角〕转increment n. 增量,增加,增〔大〕长indexing table automatic n. 自动分度工作台infeed grinding n. 切入式磨削installation n. 装置,设备,台,站,安装,设置internal grinding n. 内圆磨削involute hob n. 渐开线滚刀Jjig boring machine n. 坐标镗床Kkeyway cutting n. 键槽切削加工knurling tool n. 滚花刀具,压花刀具,滚花刀Llaedscrew machine n. 丝杠加工机床lap grinding n. 研磨lapping n. 研磨,抛光,精研,搭接,擦准lathe n. 车床lathe dog n. 车床轧头,卡箍,鸡心夹头,离心夹头,制动爪,车床挡块lathe tool n. 车刀level n. 水平,水准,水平线,水平仪,水准仪,电平,能级,程度,强度,a. 水平的,相等的,均匀的,平稳的loading time n. 装载料时间,荷重时间,充填时间,充气时间lock n. 锁,栓,闸,闭锁装置,锁型,同步,牵引,v. 闭锁,关闭,卡住,固定,定位,制动刹住longitudinal grinding n. 纵磨low capacity machine n. 小功率机床〔机器〕Mmachine axis n. 机床中心线machine table n. 机床工作台machine tool n. 机床,工作母机machining n. 机械加工,切削加工machining (or cutting) variable n. 加工(或切削)变量machining allowance n. 机械加工余量machining cycle n. 加工循环machining of metals n. 金属切削加工,金属加工magazine automatic n. 自动化仓库,自动化料斗,自动存贮送料装置manufacture n. 制造者,生产者,厂商,产品,制造material removing rate n. 材料去除率metal cutting n. 金属切削metal-cutting technology n. 金属切削工艺学,金属切削工艺〔技术〕metal-cutting tool n. 金属切削刀具,金属切削工具micrometer adjustment n. 微调milling n. 铣削,磨碎,磨整,选矿milling feed n. 铣削进给,铣削走刀量,铣削走刀机构milling machine n. 铣床milling spindle n. 铣床主轴milling tool n. 铣削刀具,铣削工具mount v. 固定,安装,装配,装置,架设,n. 固定件,支架,座,装置,机构mounting n. 安装,装配,固定,机架,框架,装置mounting fixture n. 安装夹具,固定夹具NNose n. 鼻子,端,前端,凸头,刀尖,机头,突出部分,伸出部分number of revolutions n. 转数numerical control n. 数字控制numerically controlled lathe n. 数控车床Ooblique grinding n. 斜切式磨床operate v. 操纵,控制,运行,工作,动作,运算operating cycle n. 工作循环operation n. 运转,操作,控制,工作,作业,运算,计算operational instruction n. 操作说明书,操作说明operational safety n. 操作安全性,使用可靠性oscillating type abrasive cutting machine n. 摆动式砂轮切割机oscillation n. 振动,振荡,摆动,颤振,振幅out-cut milling n. 切口铣削oxide ceramics n. 氧化物陶瓷oxide-ceramic cutting tool n. 陶瓷刀具Pperformance n. 实行,执行,完成,特性,性能,成品,制作品,行为,动作,生产率,效率peripheral grinding n. 圆周磨削peripheral speed n. 圆周速度,周速,边缘速度perpendicular a. 垂直的,正交的,成直角的n. 垂直,正交,竖直,垂线,垂直面physical entity n. 实体,实物pitch n. 齿距,节距,铆间距,螺距,极距,辊距,坡度,高跨比,俯仰角pitch circle n. 节圆plain (or cylindrical) milling machine n. 普通(或圆柱形)铣床plain grinding n. 平面磨削plain turning n. 平面车床plane n. 平面,面,投影,刨,水平,程度,阶段,飞机a.平的v. 弄平,整平,刨,飞行plane milling n. 平面铣削plane-mill n. 平面铣刀,平面铣床plunge mill n. 模向进给滚轧机plunge-cut n. 切入式磨削,横向进给磨削,全面进刀法,全面进给法plunge-cut thread grinder n. 切入式螺纹磨床plunge-grinding n. 切入式磨削point n. 点,尖端,刀尖,针尖,指针,交点,要点,论点,特点v. 指,面向,瞄准,对准,表明,弄尖,强调power n. 功率,效率,能〔容,力〕量,动力,电源,能源v. 驱〔拖,带,发〕动,给...以动力power hacksaw n. 机动弓锯〔钢锯〕precision boring n. 精镗precision boring machine n. 精密镗床precision machining n. 精密机械加工pressure angle n. 压力角primary cutting edge n. 主切削刃principal feed motion n. 主进给运动,主进刀运动production method s n. 生产方法[式]profile n. 轮廓,形面,剖面,侧面图,分布图。

机床行业常用英文(中文)对照

机床行业常用英文(中文)对照

机床行业常用英文对照(1): 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Generated by Foxit PDF Creator © Foxit Software For evaluation only.Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Generated by Foxit PDF Creator © Foxit Software For evaluation only.Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机V ertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手(2):按中文拼音字母排序铝轮冒口切断机 Overflow cutting machines for aluminium wheels 离心压力机 Presses,eccentric六角立式铣床 Milling machines,turret vertical六角车床 Lathes,turret螺栓,螺帽及螺丝 Bolts,screws & nuts螺纹磨床 Grinders,thread冷却机 Coolers冷锻 Forging,cold冷锻冲压机 Presses,cold forging立式双柱加工中心 Machining centers,vertical double-column type 立式铣床 Milling machines,vertical立式油压拉床 V ertical hydraulic broaching machine立式刨床 Planing machines vertical立式车床 Lathes,vertical立式带锯 Saws,vertical band立式加工中心 Machining centers,vertical立式及卧式铣床 Milling machines,vertical & horizontal立式钻床 Drilling machines,vertical联轴器 Coupling连续溶解保温炉 Aluminum continuous melting & holding furnaces 连续冲模 Dies-progressive链传动 Chain drive切断机 Cutting-off machinesCNC刀杆 CNC toolings曲柄压力机 presses,crank修整机 Finishing machines舍弃式刀头 Disposable toolholder bits润滑系统 Lubrication Systems润滑液 Lubricants熔热处理炉 Heating treatment funaces三爪、分割工具头 3-Jaws indexing spacers伺服冲床 Presses,servo输送链 Conveying chains手工具 Hand tools砂轮修整器 Wheel dressers蚀刻机 Etching machines外圆磨床 Grinding machines,cylindrical搪磨机 Honing machines搪孔头 Boring heads卧式铣床 Milling machines,horizontal卧式带锯 Saws,horizontal band卧式加工中心 Machining centers,horizontal卧式及立式加工中心 Machining centers,horizontal & vertical万能铣床 Milling machines,universal万能磨床 Grinding machines,universal镗床 Boring machines弯曲机 Bending machines弯管机 Tube bending machines通用加工中心 Machining centers,general铜锻 Forging,copper铣头 Milling heads铣床 Milling machines无心磨床 Grinding machines,centerless无心精研机 Lapping machines,centerless压模 Pressing dies压铸冲模 Die casting dies压铸机 Die casting machines油冷却器 Oil coolers造链机 Chain making tools造线机 Cable making tools造钉机 Nail making machines印刷电器板油压冲孔脱料系统 PCB fine piecing systems摇臂钻床 Drilling machines,radial硬(软)板(片)材及自由发泡板机组 Hard/soft and free expansion sheet making plant辗压机 Rolling machines液压元件 Hydraulic components液压冲床 Presses,hydraulic液压动力元件 Hydraulic power units液压工具 Hydraulic power tools液压回转缸 Hydraulic rotary cylindersGenerated by Foxit PDF Creator © Foxit Software For evaluation only.P型PVC高分子防水 P type PVC waterproof rolled sheet making plant 刨床 Planing machines牛头刨床 Shapers其他铸造 Casting,other其他锻造 Forging,other模芯 Mold core模具 Molds模具维修 Mold repair模具打磨/磨纹 Mold polishing/texturing模具单元 Mold & die components模具加热器/冷却器 Mold heaters/chillers磨轮 Grinding wheels磨削工具 Grinding tools磨床 Grinding machines磨床工作台 Grinder bench平衡设备 Balancing equipment气油压虎钳 Pneumatic hydraulic clamps气动冲床 Presses,pneumatic气动工具 Pneumatic power tools轴 shafts轴承 Bearings轴承配件 Bearing fittings轴承加工机 Bearing processing equipment肘杆式压力机 Presses,knuckle joint铸铝 Casting,aluminium铸铜 Casting,copper铸造设备 Foundry equipment铸钢 Casting,steel铸灰口铁 Casting,gray iron织麦激光切割机 Woven-Cutting machines重力铸造机 Gravity casting machines重型车床 Lathes,heavy-duty主轴 spindles扳手 Wrenches拔丝机 Drawing machines保温炉 Heat preserving furnaces插床 Slotting machines齿轮 Gears齿轮切削机 Gear cutting machines冲压机 Stamping parts冲子研磨器 Punch formers超声波打磨机 Grinders,ultrasonic车床工作台 Lathe bench磁性工具 Magnetic tools传动链 Transmitted chains床身式铣床 Milling machines,bed type带传动 Belt drive带锯 Saws,band带锯床 Sawing machines,band电脑数控镗床 CNC boring machines电脑数控弯折机 CNC bending presses电脑数控铣床 CNC milling machines电脑数控线切削机 CNC wire-cutting machines电脑数控磨床 CNC grinding machines电脑数控车床 CNC lathes电脑数控电火花线切削机 CNC EDM wire-cutting machines电脑数控电火花机 CNC electric discharge machines电脑数控雕刻机 CNC engraving machines电脑数控机床配件 CNC machine tool fittings电脑数控剪切机 CNC shearing machines电脑数控钻床 CNC drilling machines电动刀具 Electric power tools电火花机 Electric discharge machines(EDM)雕刻机 Engraving machines刀片 Blades刀具 Cutters倒角机 Chamfer machines多轴钻床 Drilling machines,multi-spindle锻铝 Forging,aluminium锻压机 Presses,forging锻模 Forging dies仿形铣床 Milling machines,duplicating粉末冶金成型机 Powder metallurgic forming machines反射炉 Reverberatory furnaces钢锻 Forging,steel高速车床 Lathes,high-speed高速钻床 Drilling machines,high-speed管筒制造机 Pipe & tube making machines滚筒 Rollers工具磨床 Grinders,tools & cutters攻螺丝机 Tapping machines弓锯 Saws,hack虎钳 Vises换模系统 Mold changing systems夹盘 Chucks夹具 Fixture夹具/支持系统 Clamping/holding systems剪切机 Shearing machinesGenerated by Foxit PDF Creator © Foxit Software For evaluation only.加工中心机刀库 A.T.C.system激光切割 Laser cutting激光雕刻机 Engraving machines,laser激光钢板切割机 Laser cutting for SMT stensil 集合管 Manifolds矫直机 Straightening machines金属板成型机 Sheet metal forming machines 金属板加工机 Sheet metal working machines 锯片 Blades,saw锯床 Sawing machines卷边工具 Crimping tools晶圆切割机 Dicing saws精密平口钳 Vises,tool-maker精研机 Lapping machines可锻铸铁 Casting,malleable iron快速换模系统 Quick mold change systems卡口 Bayonet开关及按钮 Switches & buttons钻石刀具 Diamond cutters钻头 drills钻模 Jigs钻床 Drilling machines钻床工作台 Drilling machines bench自动压力机 Presses,transfer自动车床 Lathes,automatic注油机 Lubricators转台 Rotary tables Generated by Foxit PDF Creator © Foxit Software For evaluation only.。

太全了船舶工具的英语词汇

太全了船舶工具的英语词汇

太全了船舶工具的英语词汇1.车床 Lathe2.刨床 Planing machine3.钻床 Drill machine4.砂轮机 Grinding machine5.磨床 Grinder6.铣床 Milling machine7.镗床 Boring machine8.手锤Engineer’s hammer9.冲击板手 Impact wrench10.板手 Spanner11.活络板手 Screw spanner12.梅花板手 Ring spanner13.呆扳手 Open spanner15.套筒板手 Socket spanner16.管子钳 Pipe spanner17.螺丝刀 Screw driver18.钢丝钳 Wire pliers19.尖嘴钳 Long nose pliers20.钢锯 Hack saw21.剪刀 Scissors22.手电筒 Torch23.扁铲(凿子) Chisel24.锉刀 File25.丝攻 Thread tap26.板牙 Thread die27.绞刀 Reamer28.刮刀 Scraper29.油石 Oil stone30.拔子(拉马) Puller31.沙布 Emery cloth32.破布 Rag33.卷尺 Measuring tape34.空心冲 Hole punch35.样冲 Joint punch36.油壶 Oil gun37.牛油枪 Grease gun38.手电钻 Handle drill39.钻头 Drill40.液压千斤 Hydraulic jack.41.塞尺 Feeler gauge42.游标卡尺 Vernier caliper43.外卡尺 Outside calipers44.内卡尺 Inside calipers45.螺纹量规 Screw gauge46.桥规 Bridge gauge47.电焊机 Electrode welding machine 48.气焊机 Gas welding machine 49.电焊钳 Electric welding pliers 50.气割枪 Cutting touch51.电焊条 Electric soldering iron 52.电工刀 Electrician knife53.电笔 Test pen54.剥线钳 Wire stripping pliers 55.圆规 Compass56.量表 Gauge57.拐档表 Crank deflection gauge 58.深度规 Depth gauge59.千分表 Micrometer gauge60.台虎钳 Table vice61.柴油 Diesel oil62.滑油 Lubricating oil63.液压油 Hydraulic oil64.重油 Heavy oil65.燃油 Fuel oil66.黄油 Grease67.螺栓 Bolt68.螺帽 Nut69.垫片 Washer70.研磨沙 Grinding sand71.研磨膏 Grinding paste72.石棉板 Asbestos plate73.青壳纸 Fish paper74.盘根 Packing75.细钢丝 Thin steel wire76.密封圈 Rubber seal ring77.塑料管 Plastic pipe78.胶皮管 Rubber hose79.电灯泡 Electric bulb80.工作灯 Working lamp81.插头 Electric plug82.插座 Electric socket.83.喷砂机 Sand blaster outfit84.空气马达 Air motor85.油柜清洁器 Tank cleaning machine 86.高压冲水机 High pressure hose for hydraulic 87.真空泵 Vacuum pump88.套筒扳手组 Socket wrench set89.深头套筒 Deep socket wrench90.套筒扳手 Box wrench91.单开口扳手 Single open end wrench 92.双开口扳手 Double open end wrench 93.转矩扳手 Torque wrench94.电动机扳手 Motor wrench95.侧剪钳 Slide cutting plier96.活节钳 Combination plier97.可调快速扳手 Speed wrench98.螺丝起子 Screwdriver99.偏向螺丝起子 Offset screw100.六角螺帽起子组 Hexagon nut drivers set 101.手摇钻 Straight hand drill 102.手工锯 Hacksaw frame103.锯片 Hacksaw blade104.砂纸 Silicon paper105.手拉葫芦 Chain block106.高压管 High pressure hose 107.液压千金顶 Hydraulic jack108.锤子 Hammer109.平錾 Cold chisel110.活动扳手 Adjustable wrench 111.螺丝刀 Screwdriver112.侧剪铗 Side cutting hipper 113.螺栓剪 Cable cutter114.敲击管钳 Rap wrench115.砂轮 Grinding wheel116.老虎钳 Utility vise117.直梯 Straight ladder118.踏梯 Step ladder119.平台推车 Platform trunk120.搬平车 Gas cylinder carrier 121.注油机 Grease lubricator122.强力油泵 Heavy duty pump oiler 123.油壶 Oil jag124.麻花钻 Twist drill125.绞刀 Pin reamer126.旋转中心钻 Rolling center127.弹性带尺 Convex rule128.不锈钢直尺 Stainless steel straight rule 129.平面规 Surface gauge130.平行直角定规 Precision flat try square 131.温度计 Thermometer。

机加工专业单词中英对照

机加工专业单词中英对照

机加工专业(单词/词组)中英对照Aabrasion n. 磨料,研磨材料,磨蚀剂, adj. 磨损的,磨蚀的abrasive belt n. 砂带abrasive belt grinding n. 砂带磨削,用研磨带磨光abrasive cut-off machine n. 砂轮切断机abrasive dressing wheel n. 砂轮修整轮abrasive grain n. 磨料粒度abrasive grit n. 研磨用磨料,铁粒abrasive lapping wheel n. 磨料研磨轮accuracy of position n. 位置精度accuracy to shape n. 形状精度active cutting edge n. 主切削刃adapter flange n. 连接器法兰盘adjointing flanks n. 共轭齿廓align n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准angle milling cutter n. 角铣刀angular grinding n. 斜面磨削,斜磨法angular milling n. 斜面铣削angular plunge grinding n. 斜向切入磨削angular turning n. 斜面车削arbour n. 刀杆,心轴,柄轴,轴,辊轴attachment n. 附件,附件机构,联结,固接,联结法automatic bar machine n. 棒料自动车床automatic boring machine n. 自动镗床automatic copying lathe n. 自动仿形车床automatic double-head milling machine n. 自动双轴铣床automatic lathe n. 自动车床automatic turret lathe n. 自动转塔车床Bbelt grinding machine n. 砂带磨床bench lathe n. 台式车床bevel n. 斜角,斜面,倾斜,斜切,斜角规,万能角尺,圆锥的,倾斜的,斜边,伞齿轮,锥齿轮bevel gear cutting machine n. 锥齿轮切削机床bevel gear tooth system n. 锥齿轮系,锥齿轮传动系统borehole n. 镗孔,镗出的孔,钻眼boring n. 镗孔,钻孔,穿孔boring fixture n. 镗孔夹具boring machine n. 镗床boring tool n. 镗刀boring, drilling and milling machine n. 镗铣床broaching machine n.拉床,铰孔机,剥孔机broaching tool n. 拉刀broad finishing tool n. 宽刃精切刀,宽刃精车刀,宽刃光切刀CCalibrate vt. 校准〔正〕,刻度,分度,检查〔验〕,定标,标定,使标准化,使符合标准cam contour grinder n. 凸轮仿形磨床carbide tip n. 硬质合金刀片carbide turning tool n. 硬质合金车刀carbide-tipped tool n. 硬质合金刀具cast iron machining n. 铸铁加工,铸铁切削加工centerless cylindrical grinder n. 无心外圆磨床ceramic cutting tool n. 金属陶瓷刀具chamfer n.;vt. 倒角,倒棱chamfered cutting edge n. 倒角刀刃champ v. 焦急champing fixture n. 快换夹具champing jaw n. 快换卡爪chaser n. 螺纹梳刀,梳刀盘,板牙chatter vi.;n. 振动,振荡,震颤,刀振cherry n.;a. 樱桃,鲜红的,樱桃木制的chip n. 切屑,铁屑,刀片,刀头,片,薄片,芯片,基片chip breaker groove radius n. 断屑槽底半径,卷屑槽底半径chip clearance n. 切屑间隙chip cross-sectional area n. 切屑横截面面积chip curl n. 螺旋形切屑chip flow n. 切屑流chip formation n. 切屑形成chip removing process n. 去毛刺加工chip variable n. 切屑变量chuck n. 卡盘,夹盘,卡头,〔电磁〕吸盘,vt. 固定,装卡,夹紧,卡住chucker n. 卡盘车床,卡角车床circular drilling machine n. 圆工作台钻床circular path n. 环路,圆轨迹circular pitch measurement n. 周节测量circumference n. 圆周,周线,周界,周围,四周,范围close-grained a. 细颗粒的coffecient of tool thrust n. 刀具推力系数coil chip n. 卷状切屑cold circular saw n. 冷圆锯cold saw n. 冷锯column drilling machine n. 圆〔方〕柱立式钻床combined drill and milling cutter n. 复合钻铣床complete traverse grinding n. 横进给磨削,切入磨削computer-controlled machine n. 计算机控制机床,数控机床contact pattern n. 靠模continuous chip n. 连续切屑continuous spiral chip n. 连续螺旋切屑contour n. 轮廓,外形,外貌,轮廓线,回路,网路,电路,等高线,等值线,轮廓等高距a. 仿形的,靠模的contour grinding n. 仿形磨削,成形磨削contour milling n. 成形铣削,外形铣削,等高走刀曲面仿形法convex milling attachment n. 凸面铣削附件convex turning attachment n. 中凸车削附件,凸面车削附件coolant lubricant n. 冷却润滑剂coolant lubricant emulsion n. 冷却润滑乳液〔剂〕copy n. 样板,仿形,靠模工作法,拷贝复制品,v. 复制,模仿,抄录copy grinding n. 仿形磨床copy-mill n. 仿形铣copying turret lathe n. 仿形转塔车床corner n. 角,弯〔管〕头,弯管counterbore n. 埋头孔,沉孔,锥口孔,平底扩孔钻,平底锪钻, n.;vt. 扩孔,锪孔,镗孔,镗阶梯孔crankshaft grinding machine n. 曲轴磨床crankshaft turning lathe n. 曲轴车床creep feed grinding n. 缓进给磨削cross milling n. 横向铣削curly chip n. 卷状切屑,螺旋形切屑,切屑螺旋cut v.;n. 切削〔割〕,口,片,断,断开,削减,减少,断面,剖面,相交,凹槽cut off n. 切断〔开,去〕,关闭,停车,停止,断开装置,断流器,挡板,截止,截流cut teeth n. 铣齿cut-off grinding n. 砂轮截断,砂轮切割cutter n. 刀具,切削工具,截断器,切断器,切断机cutting n. 切削,切片,切割,切屑,金属屑,截槽cutting edge profile n. 切削刃轮廓〔外形,断面〕,切削刃角度cutting force n. 切削力cutting lip n. 切削刃,刀刃,钻唇,钻刃cutting operation n. 切削加工,切削操作,切削作业cutting rate n. 切削效率,切削速率cutting tool n. 刀具,切削工具,刃具cycle n. 周期,周,循环,一个操作过程,轮转,自行车cylindrical grinder n. 外圆磨床Ddamage n.;vt. 损坏〔害,伤,耗,失〕,破坏,事故,故障,伤害,危害deep-hole drilling n.深孔钻削deep-hole milling n. 深孔铣削design n. 设计,计算,计划,方案,设计书,图纸die-sinking n. 凹模dimension n. 尺寸,尺度,维度,量纲,因次direction of the feed motion n. 进给方向,进刀方向discontinuous chip n. 间断切屑distance n. 距离,间隔〔隙〕,长度,vt. 隔开double-column planer-miller n. 双柱龙门铣床dress v. 修饰,修整,平整,整理,清理,装饰,调制,准备,打磨,磨光,压平,轿直,清洗,清理,分级drilling n. 钻头,钻床,穿孔器,凿岩机,v. 钻孔,打孔,钻井,钻探drilling machine n. 钻床,钻机,钻孔机,打眼机drilling tool n. 钻孔〔削,井,眼〕工具Eedge point n. 刀口,刀刃efficiency n. 效率,效能,性能,功率,产量,实力,经济性,有〔功,实〕效end mill n. 立铣刀external grinding n. 外圆磨削Fface n. 表面,外观,工作面,表盘,屏,幕v. 面向,朝向,表面加工,把表面弄平face grinding machine n. 平面磨床face milling machine n. 端面磨床feed force n. 进给力feed motion n. 进给运动fine adjustment n. 精调,细调,微调fine boring n. 精密镗孔finish v.;n. 精加工,抛光,修整,表面粗糙度,完工,最后加工,最后阶段,涂层,涂料finish-cutting n. 精加工,最终切削fixture n. 夹具,夹紧装置,配件,零件,定位器,支架form n. 型式,类型,摸板,模型,形成,产生,成形,表格v. 形〔组,构〕成,产生,作出,成形,造型form-turn n. 成形车削free-cutting n. 自由切削,无支承切削,高速切削Ggap n. 间隔,间隙,距离,范围,区间,缺口,开口火花隙,vt. 使产生裂缝vi. 豁开gear cutting machine n. 齿轮加工机床,切齿机gear generating grinder n. 磨齿机gear hob n. 齿轮滚刀grinding cutter n. 磨具grinding force n. 磨削力grinding machine n. 磨床grinding wheel diameter n. 砂轮直径grinding wheel width n. 砂轮宽度groove n. 槽,切口,排屑槽,空心槽,坡口,vt. 切〔开,铣〕槽groove milling n.铣槽Hheadstock spindle n. 床头箱主轴,主轴箱主轴,头架轴helical tooth system n. 螺旋齿轮传动装置high precision lathe n. 高精度车床high-speed n. 高速high-speed machining n. 高速加工hob n. 齿轮滚刀,滚刀,螺旋铣刀,v. 滚铣,滚齿,滚削horsepower n. 马力hobbing machine n. 滚齿机,螺旋铣床,挤压制模压力机,反应阴模机hole n. 孔,洞,坑,槽,空穴,孔道,管道,v. 钻〔穿,冲,开〕孔,打洞hone n. vt. 磨石,油石,珩磨头,磨孔器,珩磨,honing machine n. 珩磨机,珩床,搪磨床,磨孔机,磨气缸机Iinclination n. 倾斜,斜度,倾角,斜角〔坡〕,弯曲,偏〔差,角〕转increment n. 增量,增加,增〔大〕长indexing table automatic n. 自动分度工作台infeed grinding n. 切入式磨削installation n. 装置,设备,台,站,安装,设置internal grinding n. 内圆磨削involute hob n. 渐开线滚刀Jjig boring machine n. 坐标镗床Kkeyway cutting n. 键槽切削加工knurling tool n. 滚花刀具,压花刀具,滚花刀Llaedscrew machine n. 丝杠加工机床lap grinding n. 研磨lapping n. 研磨,抛光,精研,搭接,擦准lathe n. 车床lathe dog n. 车床轧头,卡箍,鸡心夹头,离心夹头,制动爪,车床挡块lathe tool n. 车刀level n. 水平,水准,水平线,水平仪,水准仪,电平,能级,程度,强度,a. 水平的,相等的,均匀的,平稳的loading time n. 装载料时间,荷重时间,充填时间,充气时间lock n. 锁,栓,闸,闭锁装置,锁型,同步,牵引,v. 闭锁,关闭,卡住,固定,定位,制动刹住longitudinal grinding n. 纵磨low capacity machine n. 小功率机床〔机器〕Mmachine axis n. 机床中心线machine table n. 机床工作台machine tool n. 机床,工作母机machining n. 机械加工,切削加工machining (or cutting) variable n. 加工(或切削)变量machining allowance n. 机械加工余量machining cycle n. 加工循环machining of metals n. 金属切削加工,金属加工magazine automatic n. 自动化仓库,自动化料斗,自动存贮送料装置manufacture n. 制造者,生产者,厂商,产品,制造material removing rate n. 材料去除率metal cutting n. 金属切削metal-cutting technology n. 金属切削工艺学,金属切削工艺〔技术〕metal-cutting tool n. 金属切削刀具,金属切削工具micrometer adjustment n. 微调milling n. 铣削,磨碎,磨整,选矿milling feed n. 铣削进给,铣削走刀量,铣削走刀机构milling machine n. 铣床milling spindle n. 铣床主轴milling tool n. 铣削刀具,铣削工具mount v. 固定,安装,装配,装置,架设,n. 固定件,支架,座,装置,机构mounting n. 安装,装配,固定,机架,框架,装置mounting fixture n. 安装夹具,固定夹具NNose n. 鼻子,端,前端,凸头,刀尖,机头,突出部分,伸出部分number of revolutions n. 转数numerical control n. 数字控制numerically controlled lathe n. 数控车床Ooblique grinding n. 斜切式磨床operate v. 操纵,控制,运行,工作,动作,运算operating cycle n. 工作循环operation n. 运转,操作,控制,工作,作业,运算,计算operational instruction n. 操作说明书,操作说明operational safety n. 操作安全性,使用可靠性oscillating type abrasive cutting machine n. 摆动式砂轮切割机oscillation n. 振动,振荡,摆动,颤振,振幅out-cut milling n. 切口铣削oxide ceramics n. 氧化物陶瓷oxide-ceramic cutting tool n. 陶瓷刀具Pperformance n. 实行,执行,完成,特性,性能,成品,制作品,行为,动作,生产率,效率peripheral grinding n. 圆周磨削peripheral speed n. 圆周速度,周速,边缘速度perpendicular a. 垂直的,正交的,成直角的n. 垂直,正交,竖直,垂线,垂直面physical entity n. 实体,实物pitch n. 齿距,节距,铆间距,螺距,极距,辊距,坡度,高跨比,俯仰角pitch circle n. 节圆plain (or cylindrical) milling machine n. 普通(或圆柱形)铣床plain grinding n. 平面磨削plain turning n. 平面车床plane n. 平面,面,投影,刨,水平,程度,阶段,飞机a.平的v. 弄平,整平,刨,飞行plane milling n. 平面铣削plane-mill n. 平面铣刀,平面铣床plunge mill n. 模向进给滚轧机plunge-cut n. 切入式磨削,横向进给磨削,全面进刀法,全面进给法plunge-cut thread grinder n. 切入式螺纹磨床plunge-grinding n. 切入式磨削point n. 点,尖端,刀尖,针尖,指针,交点,要点,论点,特点v. 指,面向,瞄准,对准,表明,弄尖,强调power n. 功率,效率,能〔容,力〕量,动力,电源,能源v. 驱〔拖,带,发〕动,给...以动力power hacksaw n. 机动弓锯〔钢锯〕precision boring n. 精镗precision boring machine n. 精密镗床precision machining n. 精密机械加工pressure angle n. 压力角primary cutting edge n. 主切削刃principal feed motion n. 主进给运动,主进刀运动production method s n. 生产方法[式]profile n. 轮廓,形面,剖面,侧面图,分布图。

轮机英语工具及动名

轮机英语工具及动名
105.侧剪钳 Slide cutting plier
106.活节钳 Combination plier
107.可调快速扳手 Speed wrench
108.螺丝起子 Screwdriver
109.偏向螺丝起子 Offset screw
110.六角螺帽起子组 Hexagon nut drivers set
117.液压千金顶 Hydraulic jack
118.锤子 Hammer
119.平錾 Cold chisel
120.活动扳手 Adjustable wrench
121.螺丝刀 Screwdriver
122.侧剪铗 Side cutting hipper
123.螺栓剪 Cable cutter
31.低碳钢 Soft steel
32.高碳钢 High-carbon steel
33.合金钢 Alloy steel
34.木材 Wood
35.塑料 Plastic
36.球墨铸铁 Nodular iron
九、常用紧固件(Part of fixation in common use)
138.六折式尺 Six-folding rule
139.弹性带尺 Convex rule
140.不锈钢直尺 Stainless steel straight rule
141.平面规 Surface gauge
142.平行直角定规 Precision flat try square
41.塞尺 Feeler gauge
42.游标卡尺 Vernier caliper
43.外卡尺 Outside calipers

磨料磨具英汉翻译

磨料磨具英汉翻译

磨料:Abrasive/Grinding Material 磨具:Abrasive Tool Grinding Tool、abrasive products磨粒:Abrasive Grain安息角:angle of Repose人造磨料:artificial Abrasive黑刚玉:Black fused Alumina黑碳化硅:Black Silicon Carbide碳化硼:Boron carbide白刚玉:white fused alumina棕刚玉:brown fused alumina碳化硅:silicon carbide石榴石:garnet锆刚玉:zirconia alumina单晶刚玉:monocrystalline alumina 堆积密度:Bulk Density毛细现象capillarity混合粒度:Combination Grain Size 抗压强度:Compressive strength普通磨料:conventional abrasive立方氮化硼:cubic boron nitride立方碳化硅:cubic silicon carbide金刚石:diamond天然金刚砂:emery电熔刚玉:fused alumina粒度:grain size粒度组成:grain size distribution绿碳化硅:green silicon carbide粒度号:grit designation冲击韧性:impact toughness自由磨粒:losse grain粗磨粒:macrograins磁性物:magnetic Material金属衣金刚石:metal clad diamond 微晶刚玉:microcrystalline alumina 微粉:microgrits天然磨料:Natural abrasive天然刚玉:natural corundum 天然金刚石:natural diamond物理刚玉:physical corundum铬刚玉:Pink fused alumina多晶体:polycrystal立方氮化硼烧结体:polycrystalline cubic boron nitride人造金刚石烧结体:polycrystalline diamond单晶体:single crystal烧结刚玉:sintered alumina比表面积:specific surface area超硬材料:super abrasive人造金刚石:synthetic diamond砂带:abrasive belts砂布:abrasive cloth布砂带:abrasive cloth belt卷状砂布:abrasive cloth in roll页状砂布:abrasive cloth in sheets砂盘:abrasive discs砂纸:abrasive paper砂纸带:abrasive paper belt卷状砂纸:abrasive paper in rolls页状砂纸:abrasive paper in sheets砂套:abrasive sleeves粘结剂:adhesive烧结刚玉磨石:Aluminum oxide sintered stick烧结刚玉砂轮:aluminum oxide sintered wheel基材:backing平衡试验:balancing test结合剂:bond磨石:brick‘s stick固结磨具:bonded abrasive products对接砂带:butt joint belts无心磨砂轮:centreless grinding wheel 无心磨导轮:centreless regulating wheel 密植砂:closed coated闭口气孔:closed pore闭口气孔率:closed porosity布基:closed backing涂附磨具:coated abrasives复合基:combination backing复合基砂带:combination backing abrasive belt双面磨石:combination stone浓度:concentration立方碳化硼磨具:cubic boron nitride abrasive products立方氮化硼砂轮:cubic boron nitride grinding wheels立方氮化硼层:CBN section切断砂轮:cutting off wheel筒形砂套:cylinderical abrasive sleeves 筒形砂轮:cylinder wheel深切缓进给砂轮:deep cut and creep feed grinding wheel植砂密度:density of coating grain钹形砂轮:depressed center wheel金刚石磨具:diamond abrasive products 金刚石串珠:diamond bends金刚石圆锯片:diamond circular saw blades金刚石切割砂轮:diamond cut-off wheel 金刚石磨边砂轮:diamond edging wheel 金刚石滚轮:diamond dressing roller金刚石筒形砂轮:diamond cylinder wheel金刚石精磨片:diamond finishing pellets金刚石框架锯条:diamond frame saw blades金刚石砂轮:diamond grinding wheel锯齿:diamond saw segment金刚石锯切工具:diamond sawing and cutting tool金刚石绳锯:diamond wire saw稀释剂:diluent蝶形砂轮:dish wheel分散剂:dispersing agent 钝化:dulling动平衡试验:dynamic balance test电镀金刚石内圆切割锯片:electroplated diamond inner slicing disc 电镀金刚石什锦锉:electroplated diamond files电镀金属结合剂:electroplated metal bond电镀超硬磨料磨具:electroplated super abrasive products无接头砂带:endless abrasive belts钢纸基:fibre backing研磨页轮:flap wheel卡盘研磨叶轮:flap wheel with flange 带轴研磨叶轮:flap wheel with shaft 成型砂轮:form grinding wheel烧熔结合剂:fused bond动物胶粘接剂:glue bond硬度:grade砂瓦:grinding segment砂轮:grinding wheel碾米砂轮:grinding wheel for rice husking磨钢球砂轮:grinding wheel steel balls 砂轮工作速度:grinding wheel peripheral speed天然磨石:grindstone重负荷修磨砂轮:high-pressure snagging wheel高速砂轮:high-speed grinding wheel 衍磨条:honing stick单面凸砂轮:hubbed wheel无机结合剂:inorganic bond过渡层:intermediate section接头砂带:joint abrasive belt搭接砂带:lap joint abrasive belt研磨剂:lapping compound研磨膏:lapping paste研磨液:liquid lapping compound菱苦土结合剂:magnesia bond菱苦土磨石:magnesia grindstone金属结合剂:metal bond金相砂纸:metallographic abrasive paper 椭圆磨头:mounted cone, curved side圆柱磨头:mounted plug,flat end半球形磨头:mounted plug,round end 磨头:mounted wheel油溶性研磨膏:oil soluble lapping paste 疏植砂:open coat开口气孔:open pore开孔气孔率:open porosity有机结合剂:organic bond纸基:paper backing磨粒率:percentage of grain粘贴砂盘:pressure sensitive backing discs纸浆磨块:pulp segment纸浆磨石:pulp stone砂轮:PVA grinding wheel树脂结合剂:resin bond半树脂结合剂:resin over glue bond全树脂结合剂:resin over resin bond回转强度:revolving strength回转试验:rotation test橡胶结合剂:rubber bond自锐性:self-sharpening虫胶结合剂:shellac bond烧结结合剂:sintered bond烧结金属结合剂:sintered metal bond固体研磨剂:solid lapping compound专用砂轮:special purpose wheels静平衡试验:static balance test杯型砂轮:straight cup wheel 平行砂轮:straight wheel组织:structure基体:substrate超硬磨料层:super abrasive section超硬磨料磨具:super abrasive products 超精油石:super finishing stick载体:support碗型砂轮:taper cup wheel斜边砂轮:tapered wheel薄片砂轮:thin grinding wheel螺栓紧固平行砂轮:threaded insert disk 总气孔率:total porosity真密度:true density截锥砂套:truncated cone abrasive sleeves滚抛磨块:tumbling chip abrasives不平衡(量):unbalance不平衡值:unbalance value陶瓷结合剂:vitrified bond体积密度:volume density吸水率:water absorption耐水砂布:waterproof abrasive cloth耐水布砂带:waterproof abrasive cloth belts耐水砂纸:waterproof abrasive paper耐水纸砂带:waterproof abrasive paper belt耐水粘结剂:waterproof bond水溶性研磨膏:water soluble lapping paste双面凹带锥砂轮:wheel relieved and recessed both side单面凹带锥砂轮:wheel relieved and recessed same side单面凹砂轮:wheel recessed one side双面凹砂轮:wheel recessed two side蜗杆砂轮:worm grinding wheel。

砂轮的种类(英语含图)

砂轮的种类(英语含图)

Sammy din 总结
Grinding wheel砂轮认识砂轮,学习砂轮的英语表达
砂轮主要的划分形式主要是三种:形状、结合剂和磨料。

一.分类
1、形状分类
①Straight wheel平行砂轮
②Cylinder or wheel ring筒形砂轮或轮圈
③Tapered wheel 斜边砂轮(斜边京轮)(锥形砂轮)
④Straight cup wheel 杯形砂轮
⑤ Taper cup wheel 碗形砂轮
⑥ Dish wheel 碟形砂轮
Saucer wheel 蝶形砂轮
2、磨料分类
① Corundum grinding wheel 刚玉砂轮
A. BFA 棕刚玉砂轮
B.WFA 白刚玉砂轮
②Silicon carbide 碳化硅(金刚砂)
A. black silicon carbide黑碳化硅
B.green silicon carbide 绿碳化硅
③Diamond wheel 金刚石砂轮
④CBN (cubic boron nitride grinding wheel)立方氮化硼砂轮
3、结合剂分类
①Vitrified grinding wheel陶瓷砂轮
② Resin bond wheel 树脂砂轮
③ Rubber grinding wheel 橡胶砂轮
④ Metal bond grinding wheel 金属砂轮。

铸造专业英文词汇

铸造专业英文词汇

Abating退火Abrasion磨损Abrasive paper 砂纸Abrasive wheel 砂轮Accessory 附件,活块Acicular ferrite 针状铁素体Acid refractory 酸性耐火材料Acid-proof cast iron / acid-resistance casting/ acid resisting cast iron 耐酸铸件Acid slay 酸性渣Active clay 有效粘土AFS fineness 美国铸造学会型砂粒度Agitator 搅拌机(型砂试验)Agitation 搅拌Air blower 鼓风机Air drain 出气口(浇注系统)Air pollution control 大气污染控制Air tightness 气密性Air vent 出气孔Allowance 余量,津贴,补助,宽容Alloying agent 合金元素Alloying component 合金成分Anti-rust 防锈Argon 氩气Atomization 雾化,喷雾Atomizer test 雾化试验(检验金属表面油脂)Attack 侵蚀Attack polishing method 侵蚀抛光法Automatic charging 自动加料Automatic de-sprueing 自动切除冒口Automatic molding 自动造型Automatic pouring device 自动浇注装置Automatic sand plant 自动化砂处理装置Baked core 干砂芯Balance 天平/余额Ball feeder 球状冒口Ball hardness 布氏硬度Ball hardness testing machine 布氏硬度机Ball mill 球磨机Band/belt conveyer 皮带输送机Band/belt elevator 皮带斗式提升机Bar bend test 试棒抗弯试验Base 底,基础Base line 基线Base plate 底板Base sand 原砂Basic 碱性的,基本的Batch mill / batch sand mixer 混砂机Beader pearlite 珠光体Bed charge/coke 底焦Belt grinder 带式磨光机Bending strength 抗弯强度Bentonite 膨润土Binder 粘结剂Bituminous coal dust/black dust 煤粉Black short 冷脆Black skin 黑皮,铸皮Blank 毛胚,下料Blast 鼓风,送风Blast capacity 风量Blast fan 离心式鼓风机Blast hole 风口Blast intensity 鼓风强度Blast pressure gage 风压表Blast regulator 风量调节器Blast volume 风量Bleed 缺肉,台箱跑火Blender 混砂机,搅拌机Blind feeder/head 暗冒口Blind roaster 马弗炉Blind scab 起痂Blister 皮下气泡Blow down 停炉Boiling point 沸点Bond 粘结剂,合同Bond clay 造型粘土Bond strength 粘结强度Bottom door 炉底们Bottom drop 打炉Breaking-in 带肉Brinell hardness 布氏硬度Brittleness 脆性Brittle fracture 脆性断口,脆性断裂B type graphite B型石墨Buffing 抛光Buffing machine 抛光机Bunker 料斗CE carbon equivalent 碳当量Carbide 碳化物carbon dioxide二氧化碳carbon monoxide 一氧化碳carbon pick-up 增碳carburetter 增碳剂,汽化器case hardening 表面硬化case gate 内浇口casting alloy 铸造合金casting defect/ casting flaw 铸造缺陷casting design 铸造设计casting equipmentcasting ladle 浇包casting lap 铸造冷隔casting leakage 铸造渗漏casting plan 铸造方案casting property 铸造性能casting rate 浇注速度casting skin 铸皮,黑皮casting strain 铸造(内应力)变形casting stress 铸造应力casting surface表皮casting technique 铸造工艺/技术cast integral test bar 单铸试棒caulk 腻缝,抿灰Celsius thermometer 摄氏温度计Cementite 渗碳体,碳化铁Center gate 中心浇口Center line 中心线Chain hoist 手动葫芦Charging 加料Charger 加料机Charging material 炉料/批料Chilled cast iron 冷铁Chill element 促白口元素Chilling action 激冷作用Chilling tendency 白口倾向Chrysanthemum graphite 菊花状石墨Cinder inclusion 夹渣Cinder notch 出渣口Clay washer 洗砂机Clockwise rotation 顺时针方向Clowhole / contraction cavity 锁孔Cold box process 冷芯盒制芯法Cold lap / cold shut 冷隔Collapsibility / lubricate 溃散性Consistency 稠度,浓度,一致性Continuous desulfurization 连续脱硫Contamination 污染Conveyor belt 输送带,传送带Cooling agent 冷却剂Cooling curve 冷却曲线Cooling effect 冷却作用Cooling rate 冷却速度Core 砂芯Core box Coremaking 制芯Coresetter 下芯机Cover 覆盖剂Cross gate 横浇道Crush 掉砂Cupola 冲天炉Cupola drop 打炉Cupola lining 炉衬Cupola spout 出铁槽Cut-off machine 切割机Damper 减震器Damping capacity / effect 减震能力/效果Datum face / line 基准面/线Deadhead 冒口废料Deburring 打毛刺Defect index 废品率Deformation 变形Density 密度Degreaser 脱脂剂Degree of graphitization 石墨化程度Dimensional stability 尺寸稳定性Descale 除锈,除氧化皮Decaling除锈,除氧化皮Design drawing 设计图Deslag 扒渣Destructive testing/inspection 破坏性试验/检验Desulfuration / desulphurization 脱硫Desulfurizer 脱硫剂Detection 检查,摊伤Die cavity 型腔,模腔Differential hardening / heating / quenching 局部硬化/加热/淬火Diffuse 扩散Dilatant 膨胀Dilute 稀释,冲淡Dimensional error / tolerance 尺寸误差/公差Direction l solidification 顺序凝固,定向凝固Dirt / dirt inclusion 夹渣Disintegration 溃散,崩解,分解Disk feeder 圆盘给料机Dislocation 位错Displacement 位移/置换Dissipation heat 散热Distorted patter 模变形Distortion 变形,扭曲Divorced pearlite 粒状珠光体Down runner / gate / downright 直浇口Ductile iron 球墨铸铁Duff 煤粉Durability 耐用性,耐久性Dust catcher 集尘器elastic deformation 弹性变形Elementary analysis 元素分析Elevator 提升机Elongation 延伸率,延长Endurance 耐用性,持久度Endurance limit 疲劳极限Energy loss 能量损失Environment contamination 环境污染Environmental control 污染控制Equilibrium 平衡Eutectic 共晶体,恭晶的Examination performance / result 考试成绩Fading 衰退Failure stress 破坏应力Feather 毛刺,羽毛Feeding effect 补缩效果Feeding gate 内浇口Feed/feeder head(=riser)/feeding head 冒口Ferric 铁Ferric carbide 渗碳体,碳化铁Ferrite 铁素体Ferromanganese 锰铁Ferromolybdenum 钼铁Ferrosilicon 硅铁Fettle 铲除炉壁渣子File 锉刀Filter paper/screen 滤纸/网Fin 毛刺Final machining 精加工Fine silt 粉尘Finished allowance 加工余量Finished surface 加工面Fire brick 耐火砖Fire cracking 热裂Fire resistance 耐火性Fire waste 烧损Fixture 夹具Flake form 片状Flake graphite 片状石墨Flaking off (=spalling) 剥落Flash point 闪点Flaw detection 探伤Floatation 漂浮Flowability/fluidity 流动性Flow-chart 流程图Fluid contraction 液态收缩Flushing 流渣Fold 冷隔Foreign substance 杂质Forging 锻造Forklift 叉车Free carbide 游离碳化物Free cementite 游离渗碳体Free ferrite 游离铁素体Freeting/fritting 烧结Frictional coefficient 摩擦系数Front slagging 炉前出渣Galvanizing 电镀Gas blow/hole 气孔Gas blowhole 气孔Gaseous diffusion 气体扩散Gassy melt 含气金属液Gas tightness 气密性Gate area 浇口面积Gating = gating system 浇口,浇口系统Gating design 浇口设计Gating proportion/ratio 浇口比Gauge=gage 表,计,规Globular cementite / pearlite 粒状渗碳体/珠光体Grain-boundary segregation 晶界偏析Grain fineness distribution 粒度分布Graphite floatation 石墨漂浮Graphitization 石墨化Green compression strength 湿压强度Gray/grey cast iron 灰铁Grinding 打磨,磨制Grinding wheel 砂轮Heat loss 热损失Heat stress 热应力Heat-treating / heat treatment 热处理Heating effect 热效应Heavy casting 大型铸件/厚壁铸件Heavy-walled 厚壁的Holding furnace 保温炉Hot tear/pool 热裂Hydraulic jack 液压千斤顶Hydrogen 氢Hyxagonal screen 六角筛Impact hardness/toughness 冲击硬度/韧性Impermeability 气密性,不渗透性Impression 压痕,型腔,凹腔Impurity 杂质Included slag 夹渣Indigeous graphite 析出石墨Induction 感应Inoculant 孕育剂Inoculation fade 孕育衰退Inside diameter 内经Instantaneous ladle inoculation / stream inoculation 瞬时浇包孕育Insulation 绝缘,隔离Internal porosity 内缩松Internal shrinkage 内部缩孔Internal stress 内应力Inverse chill 反白口Inverted chill 反白口Iron carbide 渗碳体,碳化铁Iron-coke ratio 铁焦比Jack 千斤顶Jet test 喷射试验(侧电镀层厚度)Job rate 生产定额Knock-off head 易割冒口Knockout 落砂,出芯Knop 钮,电钮Labile 不稳定的Labor-intensive area 强劳动(力)区Ladle 浇包Lamellar pearlite/laminate pearlite 片状珠光体Late inoculation/post inoculation 二次孕育Laying out 设计Leaker 浇漏,漏铁水lift truck 叉车Light casting 小铸件,薄壁铸件Liquidus 液相线Locating point/surface 基准点/面Loss on ignition 烧损Lower limit 下限Luster 光泽Machinability 切削性能Machine allowance 加工余量Machining 机械加工Macrograph 宏观Magnetic flaw detection 磁力探伤Magnetic field 磁场Magnetic-particle inspection 磁粉探伤Magnetic powder inspection 磁粉探伤Magnification 放大倍数,放大倍率Manganese 锰Margin tolerance 极限公差Mass production 大量生产Matrix hardness 机体硬度Mean diameter / stress 平均直径/应力Mean value 中间值Mechanical allowance 加工余量Mechanical property 机械性能Meltableness 可溶性Melting 溶解Melting capacity/ condition / efficiency 熔化率/状况/效率Melting point 熔点Metal graphic microscope 金相显微镜Metallic charge to coke ratio 铁焦比Metallic pattern 金属模Metallograph 金相图片Metallographic examination 金相检验Metallographic laboratory 金相试验室Metallographic microscope 金相显微镜Metallographic specimen 金相磨片Metallurgy 冶金学Metal material 金属材料Microanalysis 微量分析,显微分析Microlug 球化率怀素测定试帮Micron 微米Mismatch 错模Misrun 缺肉,浇不到Modulus of elongation 延伸率Molding line 造型线Natural gas 天然气Nodularization 球化Nodularizer 球化剂Notch brittleness 缺口脆性Off-dimension 尺寸不合格(常指铸件)Off-gage 尺寸不合格(常指型芯)Offset 错位,偏置Operation life 使用期限,寿命Outer inspection / visual inspection 外观检验Outlet 出口,排出口Oxidation 氧化Oxide ferric 氧化铁,三氧化二铁Partial hardening / local hardening 局部淬火Parting face 分型面,分模面Pattern plate 模板Patter spray 脱模液Pattern taper / patter draft 拔模斜度Pearlite 珠光体Permeability test 透气性试验Phosphide 磷共晶,磷化物Physical property 物理性能Pig iron 生铁Pin hole 针孔Pitted skin 麻面(铸造缺陷)Plastic binder 树脂粘结剂Plastic deformation 塑性变形Plate feeder 圆盘给料机Plating 电镀Polishing 抛光Porous casting 不致密铸件,多孔铸件Post inoculation 二次孕育Poured short 未浇满(铸造缺陷)Preheat/preheating 预热Premature freezing 过早凝固Premium casting 保质量逐件,优质逐件Preset program 预定计划,预定程序表Pressure atmosphere 大气压Pressure feeder 加压冒口Production capacity 生产能力Protective gloves 劳保手套Prototype casting 试生产铸件Push-off 推出,顶出Quench aging 淬火时效Radiator 散热器,散热片,暖气片Radioactive element 放射性元素Rare earth 稀土Rare gas 惰性气体Rat 多肉Reamer 铰刀Reclamation 再生,回用Red brittleness=hot brittleness 热脆性Reducibility 还原能力Reduction in area 断面收缩Refractoriness 耐火性Refractory property 耐久性能Regulator 调节器Reinforcement 加固Rejected casting 不合格铸件Resin 树脂Returns 回炉料Reverse chill 反白口Revolving table feeder 圆盘给料机Rimhole 皮下气泡Riser 冒口Rockwell hardness 洛氏硬度Rosette graphite 菊花状石墨Roughing 粗加工’Roughness 粗糙度Rounding 倒角Roust inhibitor 防锈剂Runner gate 横浇道Runner system 浇注系统Running and feeding system 浇冒口系统Rust prevention 防锈Rustless steelSafety and industrial gloves 劳动保护手套Safety factor 安全系数Safety goggle 护目镜Safety precaution 安全措施Sample inspectionSampling 取样Sand blister 砂眼Sand blow 气孔Sand buckle 起皮、夹砂Sand burning 粘砂Sand-conditioning system 砂处理系统Sand control 型砂控制Sand core 砂芯Sand cut 冲砂Sand defects 型砂造成的(铸造)缺陷Sand drop 掉砂Sand explosion 砂眼Sand fineness 砂子平均粒度Sand flowability 型砂流动性Sand mill / sand mixer / sand mixing machine / sand muller 混砂机Sand mold 砂型Sand shakeout 落砂Sand wash 冲砂Scab 铸痂Scar 凹痕Semi-finished product 半成品Sensitivity 敏感性Separate cast test bar = cast integrate test bar 单铸试棒Shakeout 落砂/落砂机Shaking conveyer 震动输送机Shift 班次Short-run 浇不满Short run casting 浇不足铸件,缺肉铸件(未浇满)Shrink hole收缩、锁孔Shrinkage porosity 缩松Shrinkage strain 收缩变形Shrinkhead 冒口Sintering 烧结Size tolerance 尺寸公差Slagging -off 除渣/扒渣Solidification contraction/shrinkage 凝固收缩Solid-liquid interface 固液相交界面Solidus/solidus curve/solidus line 固相线Solution concentration 溶液浓度Sonic inspection 听声检验Specific weight 比重Spectroanalysis 光谱分析Spherical graphite 球状石墨Spheroidal iron = ductile iron 球墨铸铁Spheroidization 球化Spindle 主轴Spotting point 基准点Steam tight test / air tight test 气密性试验Sticker / rat 多肉Straightening 校正Strength test 强度试验Stress 应力Stress relief 应力消除Subskin blowhole / subsurface blow hole / sub-surface blister 皮下气孔Superficial cementation 表面渗碳Super heating 过热Supersaturation 过饱和Surface finish 表面光洁度Surface folding 冷隔Surface roughness 表面粗糙度Swell 胀砂Tap hole 出渣口Telltale 定位标记Tenacity / tensile strength 抗拉强度/韧性Tensile testing machineTension-active element 反球化元素、干扰元素Test bar 试棒Test block 试块Test piece 试样Test specimen 试样/试棒/试块Thermal balance 热平衡Thermal conductivity 导热系数,导热性Thermaldeformation/dilatometer/expansion/fatigue 热变形/膨胀仪//膨胀/疲劳Tightness 紧密度,致密度Tolerance 公差Tooling point 基准点Tuyere gate 风眼Ultimate 极限Upper limit 上限Vacuum treatment 真空处理Ventilating system/device/equipment 通风系统/装置/设备Venting quality透气性Vibratory feeder 震动给料机Vibratory shakeout machine = vibratory shakeout 震动落砂机Visual examination/inspection 外观检验Wash 冲砂Washer 洗砂机Wearability / wear resistance 耐磨性Wrinkle 皱皮Yield strength 屈服强度Zero defect casting 无缺陷铸件Zinc 锌最新铸造标准应用手册(机械工业出版社)(铸造专业词汇)Foundry terminologyfoundry founding casting铸造foundry technology铸造工艺casting铸件sand casting process型砂铸造special casting process特种铸造fluidity流动性mold-filling capacity充型能力gas absorption吸气undercooling ,supercooling过冷degree of undercooling过冷度nucleation成核homogeneous nucleation自发成核heterogeneous nucleation非自发成核solidification range凝固温度范围directional solidification定向凝固solidification contraction凝固收缩liquid contraction液态收缩solid contraction固态收缩solidification time凝固时间free contraction自由收缩hindered contraction受阻收缩shrinkage铸件线收缩率contraction stress收缩应力thermal stress热应力transformation stress相变应力casting stress铸造应力residual stress残留应力metallic raw material金属原物料pig iron生铁ferro-alloy铁合金foundry returns回炉料master alloy中间合金foundry coke铸造焦炭metallurgical coke冶金焦炭fixed carbon固定碳flux熔剂degassing flux除气熔剂covering flux覆盖熔剂refining flux精炼熔剂refractoriness耐火度firebrick耐火砖fireclay耐火黏土silica brick硅砖grain magnesite镁砂molding material造型材料sand砂washed-out sand水洗砂silica sand硅砂natural sand天然砂artificial sand人工砂naturally clay-bonded sand天然粘土砂olivine sand橄榄石砂chromite sand硌铁矿砂zircon sand锆砂carbon sand炭粒砂sharp sand精硅砂red sand红砂chamotte sand熟料砂binder粘结剂clay粘土inorganic binder无机粘结剂organic binder有机粘结剂kaolin高岭土bentonite膨润土sodium bentonite钠基膨润土calcium bentonite钙基膨润土activated bentonite活化膨润土drying oil干性油no bake binder自硬粘结剂(冷硬粘结剂)thermosetting resin binder热固树脂粘结剂oil based binder油类粘结剂water glass binder,sodium silicate binder水玻璃粘结剂lignin liquor纸浆残液synthetic fat binder合脂粘结剂水玻璃模数sodium silicate modulus附加物additives发热剂exothermic mixture分型剂(脱模剂)parting agent;stripping agent 固化剂(硬化剂)hardener悬浮剂suspending agent涂料coating 型砂制备(砂处理)sand preparation混砂sand mixing;sand mulling型砂(造型混合料)molding sand芯砂(造芯混合料)core sand合成砂synthetic sand自硬砂self-hardening sand水玻璃砂sodium silicate-bonded sand覆模砂precoated sand烂砂泥(麻泥)loam调匀砂temper sand面砂facing sand背砂(填充砂)backing sand单一砂unit sand含泥量clay content含水量(水分,湿度)moisture content 旧砂floor sand枯砂(焦砂)burnt sand废砂waste sand热砂hot sand松砂aeration,sand-cutting筛分(筛析)screen analysis旧砂处理sand reconditioning旧砂再生sand reclamation沉降分选elutriation,decantation型砂试验sand testing透气性permeability流动性flowability型砂强度sand strength湿强度green strength干强度dry strength耐用性(复用性)durability砂型(芯)硬度mold hardness热变形hot deformation残留强度retained strength热强度hot strength韧性toughness发气率(发气速度)gas evolution rate发气性(发气量)gas evolution吸湿性moisture absorption落砂性knock-out capability溃散性collapsibility胶质价colloid index破碎指数shatter index热气流烘砂装置hot pneumatic tube drier 混砂机sand muller,sand mixer松砂机aerator ,sand cutter冷却提升机cooling elevator,coolevator 筛砂机riddle磁力滚筒magnetic separator旧砂再生设备sand reclamation气力输送装置pneumatic tube conveyor铸铁cast iron铸铁石墨形态morphology of graphite in cast iron灰铸铁(灰口铸铁)gray cast iron白口铸铁white cast iron麻口铸铁mottled cast iron共晶度degree of saturation碳当量carbon equivalent片状石墨flake graphite初生石墨primary graphite孕育铸铁inoculated cast iron球墨铸铁spheroidal graphite cast iron,nodular graphite iron,ductile iron球状石墨spheroidal graphite,nodular graphite 可锻铸铁(马铁)malleable cast iron黑心可锻铸铁black heart malleable cast iron珠光体可锻铸铁pearlitic malleable cast iron铁素体可锻铸铁ferritic malleable cast iron白心可锻铸铁white heart malleable cast iron团絮石墨tempered graphite冷硬铸铁(激冷铸铁)chilled iron耐磨铸铁wear resisting cast iron耐热铸铁heat resisting cast iron耐酸铸铁acid resisting cast iron高硅铸铁high silicon cast iron蠕墨铸铁vermicular cast iron,compacted graphite cast iron蠕虫状石墨vermicular graphite合金铸铁alloy cast iron铸钢cast steel碳素铸钢carbon cast steel低合金铸钢low alloy cast steel高锰钢high manganese steel铁素体钢ferritic steel青铜bronze铅青铜lead bronze铝青铜aluminum bronze黄铜brass铝铜合金aluminum-copper alloy铝镁合金aluminum-magnesium alloy铝硅合金aluminum-silicon alloy镁合金magnesium alloy轴承合金(减摩合金)bearing metal,antifrictional metal巴氏合金Babbitt metal 钛合金titanium alloy熔化(熔炼)melting重熔remelting炉料charge熔化率melting rate炉料计算charge calculation双联熔炼duplexing元素烧损(元素烧损率)melting losses of various chemical elements熔炼损耗(烧损) total melting loss还原气氛reducing atmosphere氧化气氛oxidizing atmosphere惰性气体inert gas碱度index of basicity碱性渣basic slag酸性渣acid slag精炼refining遗传性heredity风口比tuyere ratio有效高度effective height送风强度blast intensity预热送风hot blast底焦coke bed层焦coke split隔焦buffer coke charge炉衬furnace lining碱性炉衬acid lining棚料bridging熔池bath吸碳carbon pick-up焦铁比iron coke ratio出渣deslagging打炉cupola drop氧化熔炼法oxidizing melting不氧化熔炼法dead melting真空熔炼vacuum refining熔渣slag沉渣sludge浮渣dross,cinder氧化期oxidizing stage还原期blocking stage还原渣reducing slag氧化渣oxidizing slag白渣white slag脱氧deoxidation扒渣slagging-off脱碳decarburization脱硫desulphurization脱磷dephosphorization增碳recarburizing脱氧剂deoxidizer挥发损耗volatilizing losses静置stewing,holding吹氮nitrogen flushing冲天炉cupola水冷冲天炉water-cooled cupola热风冲天炉hot blast cupola湿法除尘器wet cap炉缸cupola well前炉forehearth冲天炉加料机cupola charging machine爬式加料机ship hoist电磁配料称electro-magnetic weighing balancer 电磁盘electromagnetic chuck电弧炉direct arc furnace感应电炉electric induction furnace电渣炉electroslag furnace电磁搅拌electromagnetic agitation浇包ladle摇包shaking ladle底浇包bottom pouring ladle保温炉holding furnace坩呙炉crucible furnace孕育inoculation多孔塞法porous plug process变质modification墨化剂graphitizer过热superheating石墨球化处理nodularizing treatment of graphite碳当量仪eutectometer三角试块wdge test-piece真空除气vacuum degassing浇注pouring 保护气氛浇注pouring under controlled atmosphere浇注速度pouring rate浇注温度pouring temperature浇注时间pouring time浇注位置pouring position型内孕育inmold inoculation压铁weight点冒口teeming捣冒口pumping补炉patching炉龄campaign铸造工艺设计mold design铸造工艺装备设计foundry tools design铸造工艺图foundry molding drawing铸件图drawing of rough casting起模斜度pattern draft收缩余量shrinkage allowance工艺补正量molding allowance加工余量machining allowance吃砂量mo9ld thickness补贴pad分型负数joint allowance铸件尺寸公差dimensional allowance of casting 铸件重量公差weight allowance of casting铸件加工基准面reference face for machining of casting铸件表面粗糙度surface roughness of casting浇注系统(浇口)gating system,running system 封闭式浇注系统chocked running system,pressurized gating system半封闭式浇注系统enlarged runner system开放式浇注系统unchecked running system,non-pressurized gating system浇口盆(外浇口)pouring basin浇口杯pouring cup浇口塞blanking-off plug直浇道sprue直浇道窝sprue base横浇道runner筛网芯(滤网芯)strainer core内浇道ingate离心集渣浇注系统whirl gate,dirt trap system 顶注式浇注系统top gating system底注式浇注系统bottom gating system阶梯式浇注系统step gating system雨淋浇口shower gate缝隙浇口slot gate压边浇口lip runner,kiss runner牛角式浇口horn gate热结hot spot冒口riser,feeder head冒口效率riser efficiency明冒口open riser暗冒口bland riser侧冒口(边冒口)side riser压力冒口pressure riser大气压力冒口atmospheric riser发气压力冒口(气弹冒口)gas-delivered pressure riser透气砂芯pencil core冒口径riser neck冒口根riser pad保温冒口套heat insulating feeder sleeve发热冒口套exorhermic feeder sleeve补缩距离feeding distance,feeding zone易割冒口knock-off head易割片(易割芯片)washburn core铸造工艺装备foundry tools and equipment模样(铸模、模)pattern母模master金属模metal pattern骨架模skeleton pattern石膏模plaster pattern塑料模plaslicn pattern整体模one-piece pattern分开模parted pattern,split pattern活块loose piece模板pattern plate模底板pattern mounting plate单面模板single face pattern plate双面模板match plate放样(伸图)hot dimensional drawing缩尺(模样工缩尺)shrinkage rule,pattern-maker’s rule芯盒core box脱落式芯盒troughed core box下芯量具core setting scale 下芯夹具core jig烘芯板core drying plate砂箱flask,molding box箱带(箱挡)flask bar,cross bar脱箱snap flask套箱mold jacket套销hollow pin,stub pin造型molding型腔mold cavity7.1.3铸型mold砂型sand mold上箱cope , top part下箱drag , bottom part手工造型hand molding机器造型machine molding自动化造型automatic molding分型面mold joint有箱造型flask molding两箱造型two-part molding三箱造型three-part molding不平分型面stepped joint无箱造型flaskless molding脱箱造型removable flask molding地坑造型pit molding刮板造型sweep molding抛砂造型impeller ramming组芯造型core assembly molding假箱造型oddside molding微振压造型vibratory squeezing molding 高压造型high pressure molding湿砂型green sand mold干砂型dry sand mold砂型烘干mold drying干砂型(干型)dry sand mold表面烘干型skin dried mold烂砂泥型loam mold砂床bed过渡角transition angle吊砂cod砂钩lifter负亚造型vacuum molding液态砂造型fluid sand molding漏砂pattern stripping填砂molding-filling紧实ramming震实jolt ramming压实squeezing ramming紧实度degree of ramming二氧化碳法造型2CO process自硬砂造型self-hardening sand molding塞砂tucking刮砂strike-off造型生产线molding line刷水swabbing扎出气孔venting排气道venting channel修型patching冷铁densener,chill外冷铁surface densener内冷铁internal densener验型(验箱)trial closing合型(合箱、组型)mold assembling,closing造芯(制芯)core making芯(芯子)core芯骨core rod,core scab油砂芯oil sand core预制砂embeded core,ram up core芯头core print芯座core print芯头斜度core print taper芯头间隙core print clearance壳芯shell core烘芯core baking通气蜡线vent wax冷芯盒法cold box process热芯盒法hot box process芯撑chaplethand tools of molding压勺heart and spoon提钩cleaner双头铜勺double ended radius sleeker镘刀trowel造型机molding machine压实造型机squeezing molding machine 震击台bumper振动台vibrating table微振压实造型机vibratory squeezer震实造型机jolt molding machine高压造型机high pressure molding machine射压造型机shooting and squeezing molding machine多触头造型机equalizing piston squeezer抛砂机sand slinger起模机drawing machine射芯机core shooter击芯机core extruder铸型输送机mold conveyor落砂shake-out除芯decoring喷砂清理sand blasting抛丸清理shot blasting水力清砂hydraulic blast水砂清砂hydraulic blast清理cleaning清砂cleaning火焰表面清理scarfing清铲chipping化学清砂chemical cleaning精整dressing and finishing落砂机knock-out machine抛丸清理机shot blast machine清理滚筒tumbling barrel抛丸落砂清理设备shot blast reclaiming equipment悬挂式磨轮swing frame grinder矫正coining焊补repair welding参补impregnation金属型铸造permanent mold casting金属型metal mold金属芯metal core覆砂金属型sand-lined metal mold排气赛venting plug排气槽air vent龟裂heat checking金属型铸造机gravity die casting machine压力铸造die-casting压铸型die-casting die动型moving die定型fixed die合型力clamping force压室pressure chamber鹅颈管gooseneck分流器spreader顶杆ejector pin溢流槽overflow well压射冲头injection piston压射比压injection pressure压射速度injection speed保压时间dwell time真空压铸vacuum die casting冲氧压铸pore-free die casting双冲头压铸acurad die casting压铸机die casting machine冷室压铸机cold chamber die casting machine 热室压铸机hot chamber die casting machine 镶铸法insert process离心铸造true centrifugal casting半离心铸造semi-centrifugal casting离心浇注centrifugal pressure casting双金属离心铸造bimetal centrifugal casting 离心铸造机centrifugal casting machine失模铸造lost pattern casting熔模铸造fusible pattern molding压制熔模fusible pattern injection压型pattern die熔模fusible pattern盐模salt pattern蜡模wax-pattern模组pattern assembly熔模涂料slurry面层涂料investment precoat撒砂stuccoing脱蜡dewaxing培烧sintering壳型制造shell molding结壳时间investing time结壳温度investing temperature硬化温度curing temperature硬化时间curing time陶瓷型制造ceramic slurry灌浆paste pouring喷烧torch firing低压铸造low-pressure diecasting 充型压力mold filling pressure保压压力dwell pressure升液管stalk真空吸铸suction casting差压铸造counter-pressure casting实型铸造full mold process泡沫塑料模Styrofoam pattern磁型铸造magnetic shot molding process凝壳铸造slush casting石膏型造型plaster molding连续铸造continuous casting铸件检验inspection of casting铸件质量分析quality analysis of casting铸件外观质量visual quality of casting铸件内在质量internal quality of casting铸件使用性能service ability of casting单铸试块separated test bar of casting附铸试块test lug缺陷铸件defective casting废品reject无损检验(无损探伤)nondestructive inspection 破坏性试验destructive testing飞翅(飞边)joint flash毛刺veining抬型(抬箱)cope raise,raised mold胀砂swell冲砂erosion,cut,wash掉砂drop,crush外渗物(外渗豆)sweat气孔blowhole针孔pinhole缩孔shrinkage缩松dispersed shrinkage疏松(显微缩松)porosity,microshrinkage冷裂cold cracking热裂hot tearing热处理裂纹heat treatment crack白点(发裂)flake冷隔cold shut,cold lap浇注断流interrupted pour鼠尾rat-tail沟槽buckle夹砂结疤(夹砂)scab机械粘砂(渗透粘砂) metal penetration 化学粘砂(烧结粘砂)burn-on表面粗糙rough surface皱皮elephant skin缩陷depression浇不到misrun未浇满poured short跑火run-out,bleeding型漏(漏箱)run-out,bleeding损伤(机械损伤)damage拉长exaggeration of dimension超重over-weight变形distortion,warping错型(错箱)shift错芯core shift偏芯(漂芯)core raised,corelift夹杂物inclusion冷豆cold shot内渗物(内渗豆)internal sweat渣气孔scum,slag-blow hole砂眼sand inclusion亮皮pearlite layer菜花头cauli-flowering石墨漂浮carbon flotation石墨集结kish graphite spot组织粗大open grain structure偏析segregation硬点hard spot反白口inverse chill球化不良under-nodularizing球化衰退degradated spheroidisation 脱碳decarburization。

机加工专业词汇

机加工专业词汇

机加工专业(单词/词组)中英对照机械英语机加工专业(单词/词组)中英对照Aabrasion n. 磨料,研磨材料,磨蚀剂, adj. 磨损的,磨蚀的abrasive belt n. 砂带abrasive belt grinding n. 砂带磨削,用研磨带磨光abrasive cut-off machine n. 砂轮切断机abrasive dressing wheel n. 砂轮修整轮abrasive grain n. 磨料粒度abrasive grit n. 研磨用磨料,铁粒abrasive lapping wheel n. 磨料研磨轮accuracy of position n. 位置精度accuracy to shape n. 形状精度active cutting edge n. 主切削刃adapter flange n. 连接器法兰盘adjointing flanks n. 共轭齿廓align n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准angle milling cutter n. 角铣刀angular grinding n. 斜面磨削,斜磨法angular milling n. 斜面铣削angular plunge grinding n. 斜向切入磨削angular turning n. 斜面车削arbour n. 刀杆,心轴,柄轴,轴,辊轴attachment n. 附件,附件机构,联结,固接,联结法automatic bar machine n. 棒料自动车床automatic boring machine n. 自动镗床automatic copying lathe n. 自动仿形车床automatic double-head milling machine n. 自动双轴铣床automatic lathe n. 自动车床automatic turret lathe n. 自动转塔车床Bbelt grinding machine n. 砂带磨床bench lathe n. 台式车床bevel n. 斜角,斜面,倾斜,斜切,斜角规,万能角尺,圆锥的,倾斜的,斜边,伞齿轮,锥齿轮bevel gear cutting machine n. 锥齿轮切削机床bevel gear tooth system n. 锥齿轮系,锥齿轮传动系统borehole n. 镗孔,镗出的孔,钻眼boring n. 镗孔,钻孔,穿孔boring fixture n. 镗孔夹具boring machine n. 镗床boring tool n. 镗刀boring, drilling and milling machine n. 镗铣床broaching machine n.拉床,铰孔机,剥孔机broaching tool n. 拉刀broad finishing tool n. 宽刃精切刀,宽刃精车刀,宽刃光切刀CCalibrate vt. 校准〔正〕,刻度,分度,检查〔验〕,定标,标定,使标准化,使符合标准cam contour grinder n. 凸轮仿形磨床carbide tip n. 硬质合金刀片(carbide tip)carbide turning tool n. 硬质合金车刀carbide-tipped tool n. 硬质合金刀具cast iron machining n. 铸铁加工,铸铁切削加工centerless cylindrical grinder n. 无心外圆磨床ceramic cutting tool n. 金属陶瓷刀具(ceramic cutting tool) chamfer n.;vt. 倒角,倒棱chamfered cutting edge n. 倒角刀刃champ v. 焦急champing fixture n. 快换夹具champing jaw n. 快换卡爪chaser n. 螺纹梳刀,梳刀盘,板牙(chaser)chatter vi.;n. 振动,振荡,震颤,刀振(chatter)cherry n.;a. 樱桃,鲜红的,樱桃木制的chip n. 切屑,铁屑,刀片,刀头,片,薄片,芯片,基片chip breaker groove radius n. 断屑槽底半径,卷屑槽底半径chip clearance n. 切屑间隙(chip clearance)chip cross-sectional area n. 切屑横截面面积chip curl n. 螺旋形切屑(chip curl)chip flow n. 切屑流(chip flow)chip formation n. 切屑形成chip removing process n. 去毛刺加工chip variable n. 切屑变量(chip variable)chuck n. 卡盘,夹盘,卡头,〔电磁〕吸盘,vt. 固定,装卡,夹紧,卡住(chuck)chucker n. 卡盘车床,卡角车床circular drilling machine n. 圆工作台钻床circular path n. 环路,圆轨迹circular pitch measurement n. 周节测量circumference n. 圆周,周线,周界,周围,四周,范围close-grained a. 细颗粒的coffecient of tool thrust n. 刀具推力系数coil chip n. 卷状切屑cold circular saw n. 冷圆锯cold saw n. 冷锯column drilling machine n. 圆〔方〕柱立式钻床(column drilling machine)combined drill and milling cutter n. 复合钻铣床complete traverse grinding n. 横进给磨削,切入磨削computer-controlled machine n. 计算机控制机床,数控机床contact pattern n. 靠模continuous chip n. 连续切屑continuous spiral chip n. 连续螺旋切屑contour n. 轮廓,外形,外貌,轮廓线,回路,网路,电路,等高线,等值线,轮廓等高距a. 仿形的,靠模的contour grinding n. 仿形磨削,成形磨削contour milling n. 成形铣削,外形铣削,等高走刀曲面仿形法convex milling attachment n. 凸面铣削附件(convex milling atta chment)(convex milling attachment)convex turning attachment n. 中凸车削附件,凸面车削附件coolant lubricant n. 冷却润滑剂coolant lubricant emulsion n. 冷却润滑乳液〔剂〕copy n. 样板,仿形,靠模工作法,拷贝复制品,v. 复制,模仿,抄录copy grinding n. 仿形磨床copy-mill n. 仿形铣copying turret lathe n. 仿形转塔车床corner n. 角,弯〔管〕头,弯管counterbore n. 埋头孔,沉孔,锥口孔,平底扩孔钻,平底锪钻, n.;vt.扩孔,锪孔,镗孔,镗阶梯孔crankshaft grinding machine n. 曲轴磨床crankshaft turning lathe n. 曲轴车床creep feed grinding n. 缓进给磨削cross milling n. 横向铣削curly chip n. 卷状切屑,螺旋形切屑,切屑螺旋cut v.;n. 切削〔割〕,口,片,断,断开,削减,减少,断面,剖面,相交,凹槽cut off n. 切断〔开,去〕,关闭,停车,停止,断开装置,断流器,挡板,截止,截流cut teeth n. 铣齿cut-off grinding n. 砂轮截断,砂轮切割cutter n. 刀具,切削工具,截断器,切断器,切断机cutting n. 切削,切片,切割,切屑,金属屑,截槽cutting edge profile n. 切削刃轮廓〔外形,断面〕,切削刃角度cutting force n. 切削力cutting lip n. 切削刃,刀刃,钻唇,钻刃cutting operation n. 切削加工,切削操作,切削作业cutting rate n. 切削效率,切削速率cutting tool n. 刀具,切削工具,刃具cycle n. 周期,周,循环,一个操作过程,轮转,自行车cylindrical grinder n. 外圆磨床Ddamage n.;vt. 损坏〔害,伤,耗,失〕,破坏,事故,故障,伤害,危害deep-hole drilling n.深孔钻削deep-hole milling n. 深孔铣削design n. 设计,计算,计划,方案,设计书,图纸die-sinking n. 凹模dimension n. 尺寸,尺度,维度,量纲,因次direction of the feed motion n. 进给方向,进刀方向discontinuous chip n. 间断切屑distance n. 距离,间隔〔隙〕,长度,vt. 隔开double-column planer-miller n. 双柱龙门铣床dress v. 修饰,修整,平整,整理,清理,装饰,调制,准备,打磨,磨光,压平,轿直,清洗,清理,分级drilling n. 钻头,钻床,穿孔器,凿岩机,v. 钻孔,打孔,钻井,钻探drilling machine n. 钻床,钻机,钻孔机,打眼机drilling tool n. 钻孔〔削,井,眼〕工具Eedge point n. 刀口,刀刃efficiency n. 效率,效能,性能,功率,产量,实力,经济性,有〔功,实〕效end mill n. 立铣刀external grinding n. 外圆磨削Fface n. 表面,外观,工作面,表盘,屏,幕v. 面向,朝向,表面加工,把表面弄平face grinding machine n. 平面磨床face milling machine n. 端面磨床feed force n. 进给力feed motion n. 进给运动fine adjustment n. 精调,细调,微调fine boring n. 精密镗孔finish v.;n. 精加工,抛光,修整,表面粗糙度,完工,最后加工,最后阶段,涂层,涂料finish-cutting n. 精加工,最终切削fixture n. 夹具,夹紧装置,配件,零件,定位器,支架form n. 型式,类型,摸板,模型,形成,产生,成形,表格v. 形〔组,构〕成,产生,作出,成形,造型form-turn n. 成形车削free-cutting n. 自由切削,无支承切削,高速切削Ggap n. 间隔,间隙,距离,范围,区间,缺口,开口火花隙,vt. 使产生裂缝vi. 豁开gear cutting machine n. 齿轮加工机床,切齿机gear generating grinder n. 磨齿机gear hob n. 齿轮滚刀grinding cutter n. 磨具grinding force n. 磨削力grinding machine n. 磨床grinding wheel diameter n. 砂轮直径grinding wheel width n. 砂轮宽度groove n. 槽,切口,排屑槽,空心槽,坡口,vt. 切〔开,铣〕槽groove milling n.铣槽Hheadstock spindle n. 床头箱主轴,主轴箱主轴,头架轴helical tooth system n. 螺旋齿轮传动装置high precision lathe n. 高精度车床high-speed n. 高速high-speed machining n. 高速加工hob n. 齿轮滚刀,滚刀,螺旋铣刀,v. 滚铣,滚齿,滚削horsepower n. 马力hobbing machine n. 滚齿机,螺旋铣床,挤压制模压力机,反应阴模机hole n. 孔,洞,坑,槽,空穴,孔道,管道,v. 钻〔穿,冲,开〕孔,打洞hone n. vt. 磨石,油石,珩磨头,磨孔器,珩磨,honing machine n. 珩磨机,珩床,搪磨床,磨孔机,磨气缸机Iinclination n. 倾斜,斜度,倾角,斜角〔坡〕,弯曲,偏〔差,角〕转increment n. 增量,增加,增〔大〕长indexing table automatic n. 自动分度工作台infeed grinding n. 切入式磨削installation n. 装置,设备,台,站,安装,设置internal grinding n. 内圆磨削involute hob n. 渐开线滚刀Jjig boring machine n. 坐标镗床Kkeyway cutting n. 键槽切削加工knurling tool n. 滚花刀具,压花刀具,滚花刀Llaedscrew machine n. 丝杠加工机床lap grinding n. 研磨lapping n. 研磨,抛光,精研,搭接,擦准lathe n. 车床lathe dog n. 车床轧头,卡箍,鸡心夹头,离心夹头,制动爪,车床挡块lathe tool n. 车刀level n. 水平,水准,水平线,水平仪,水准仪,电平,能级,程度,强度,a. 水平的,相等的,均匀的,平稳的loading time n. 装载料时间,荷重时间,充填时间,充气时间lock n. 锁,栓,闸,闭锁装置,锁型,同步,牵引,v. 闭锁,关闭,卡住,固定,定位,制动刹住longitudinal grinding n. 纵磨low capacity machine n. 小功率机床〔机器〕Mmachine axis n. 机床中心线machine table n. 机床工作台machine tool n. 机床,工作母机machining n. 机械加工,切削加工machining (or cutting) variable n. 加工(或切削)变量machining allowance n. 机械加工余量machining cycle n. 加工循环machining of metals n. 金属切削加工,金属加工magazine automatic n. 自动化仓库,自动化料斗,自动存贮送料装置manufacture n. 制造者,生产者,厂商,产品,制造material removing rate n. 材料去除率metal cutting n. 金属切削metal-cutting technology n. 金属切削工艺学,金属切削工艺〔技术〕metal-cutting tool n. 金属切削刀具,金属切削工具micrometer adjustment n. 微调milling n. 铣削,磨碎,磨整,选矿milling feed n. 铣削进给,铣削走刀量,铣削走刀机构milling machine n. 铣床milling spindle n. 铣床主轴milling tool n. 铣削刀具,铣削工具mount v. 固定,安装,装配,装置,架设,n. 固定件,支架,座,装置,机构mounting n. 安装,装配,固定,机架,框架,装置mounting fixture n. 安装夹具,固定夹具NNose n. 鼻子,端,前端,凸头,刀尖,机头,突出部分,伸出部分number of revolutions n. 转数numerical control n. 数字控制numerically controlled lathe n. 数控车床Ooblique grinding n. 斜切式磨床operate v. 操纵,控制,运行,工作,动作,运算operating cycle n. 工作循环operation n. 运转,操作,控制,工作,作业,运算,计算operational instruction n. 操作说明书,操作说明operational safety n. 操作安全性,使用可靠性oscillating type abrasive cutting machine n. 摆动式砂轮切割机oscillation n. 振动,振荡,摆动,颤振,振幅out-cut milling n. 切口铣削oxide ceramics n. 氧化物陶瓷oxide-ceramic cutting tool n. 陶瓷刀具Pperformance n. 实行,执行,完成,特性,性能,成品,制作品,行为,动作,生产率,效率peripheral grinding n. 圆周磨削peripheral speed n. 圆周速度,周速,边缘速度perpendicular a. 垂直的,正交的,成直角的n. 垂直,正交,竖直,垂线,垂直面physical entity n. 实体,实物pitch n. 齿距,节距,铆间距,螺距,极距,辊距,坡度,高跨比,俯仰角pitch circle n. 节圆plain (or cylindrical) milling machine n. 普通(或圆柱形)铣床plain grinding n. 平面磨削plain turning n. 平面车床plane n. 平面,面,投影,刨,水平,程度,阶段,飞机a.平的v.弄平,整平,刨,飞行plane milling n. 平面铣削plane-mill n. 平面铣刀,平面铣床plunge mill n. 模向进给滚轧机plunge-cut n. 切入式磨削,横向进给磨削,全面进刀法,全面进给法plunge-cut thread grinder n. 切入式螺纹磨床plunge-grinding n. 切入式磨削point n. 点,尖端,刀尖,针尖,指针,交点,要点,论点,特点v. 指,面向,瞄准,对准,表明,弄尖,强调power n. 功率,效率,能〔容,力〕量,动力,电源,能源v. 驱〔拖,带,发〕动,给...以动力power hacksaw n. 机动弓锯〔钢锯〕precision boring n. 精镗precision boring machine n. 精密镗床precision machining n. 精密机械加工pressure angle n. 压力角primary cutting edge n. 主切削刃principal feed motion n. 主进给运动,主进刀运动production method s n. 生产方法[式]profile n. 轮廓,形面,剖面,侧面图,分布图。

常用磨料磨具词汇,英汉互译,第十二更

常用磨料磨具词汇,英汉互译,第十二更

常用磨料磨具词汇,英汉互译,第十二更查看爱锐词典之磨料磨具英汉互译系列, 请在爱锐网国际站公众微信号(iabrasives)内回复关键字词:抛光、切削、修整、刀具、一、二……十一和15类(15类即磨料磨具外贸人不可不知的15类实用切磨抛行业英语词汇)即可获得十六篇常用磨料磨具英汉词汇互译汇总篇,或者请点击最下方阅读原文,先查看常用磨料磨具专业词汇,英汉互译系列之(刀具与工具的50种表达)!磨料磨具外贸人一定要知道的常用切磨抛行业英语词汇(十二)porosity 气孔率,孔隙度porosity factor 孔隙率porosity apparatus 孔率仪porosity log 孔隙度测井porous type 多孔型,孔隙类型porous type wheel 多孔轮powder metal 粉末金属ultrafine powder 超细粉,超细粉末ultrafine nickel powder 超细镍粉ultrafine palladium powder 超细钯粉precipitation tank 沉淀槽,沉降罐precision-machined 精加工的machining precision 加工精度preliminary sizing 粗筛选,初筛saw dust 锯屑,木屑screen mesh 丝网,筛孔,筛眼segmental wheel 拼合轮,砂瓦self-sharpening 自磨,自动磨锐screen separation 筛分dust separator 除尘器shaking screen 振荡筛shaking sieve 摇动筛,振动筛hob sharpener 滚刀磨床shrink hole 收缩孔,缩孔finished size 加工后尺寸,成品尺寸size grading 粒径分级,粒径级配green strength 湿强度,生坯强度stuffing 填料,填塞物superfinishing 超精加工superfinishing stone 超精加工油石,超精油石synthetic diamond 人造金刚石man-made diamond 人造金刚石metaloscope 金相显微镜macrohardness 宏观硬度milling machine 铣床mineral compound 无机化合物mirror polish 镜面抛光missing of ignition 不着火,不点火mix design 配料设计roaster mix 焙烧炉料mixing proportion 混合比,配合比例mixture calculation 配料计算mixture ratio calculation 配料比计算modified resin 改性树脂modulus 系数,模数moisture 水分,湿度moistureproof 防潮的moisture absorption 吸湿性,水分吸收moisture resistance 防潮性,抗湿性moisture barrier 防潮层moisture teller 水分测定仪,水分测定器moulding 模压成型mounted wheel 磨头cylinder mounted wheel 圆柱磨头truncated cone 截锥truncated cone mounted wheel 截锥磨头hemisphere mounted wheel 半球形磨头sphere mounted wheel 球形磨头mullite 莫来石normal distribution 正态分布normal rated power NRP 额定功率observation check 外形检查square oilstone 正方油石square honing stone 正方珩磨油石rectangular oilstone 长方油石half round oilstone 半圆油石round oilstone 圆柱油石triangular oilstone 三角油石knife blade oilstone 刀形油石operating manual 使用说明书,操作手册optimum seeking method 优选法oscillating grinding 振荡磨削,微量纵摆磨削oscillating sander 往复式砂带磨床over flow 溢流overlapping curve 交叉网纹,重合曲线oversize product 筛上物passage of chip 切屑排出通路passage of cuttings 切屑排出通道paste resin 膏状树脂,糊状树脂performance parameter 性能参数permeability of gas 透气性permeability of pure gas 纯气体透过性relative permeability of gas 气相相对渗透率petroleum coke 石油焦pickling tub 酸洗池pickling bath 酸洗槽plain cup wheel 杯形砂轮plain milling machine 普通铣床plasticity 塑性,可塑性plasticizing agent 增塑剂plate wheel 板轮,盘轮,蝶形砂轮mirror finish 镜面磨光,镜面抛光polish attack 抛光腐蚀,抛光浸蚀polish up 擦亮,磨光,改进chemical polishing 化学抛光chemical polish 化学抛光剂polishing agent 磨光剂,擦亮剂polishing cloth 抛光布polishing paper disk 抛光纸片polishing wheel 抛光轮polishing effect 抛光效应,抛光效果polishing time 抛光时间polishing tool 抛光工具polishing technology 抛光技术polishing unit 抛光设备polishing theory and practice 抛光理论和实践polishing section 抛光车间polishing runner 抛光盘polishing rouge 抛光铁丹,抛光红粉polishing roll 抛光辊,抛光轧辊polishing powder 磨光粉,抛光粉polishing process 抛光过程press polishing 压力抛光press-polishing machine 压光机polishing pressure 研磨压力,抛光压力polishing dynamic pressure 抛光动压力polishing precision 抛光精度,研磨精度precision polishing 精抛,精密抛光polishing plant 磨光工厂,磨光车间polishing performance 抛光特点,抛光性能polishing paste 抛光膏,磨光剂polishing medium 抛光介质polishing mechanism 抛光机理polishing and straightening mechanism 抛矫机理polishing machine 抛光机,磨光机polishing lathe 抛光机,抛光车床polishing material 抛光材料polishing line 磨光生产线,抛光纹,磨光线polishing filter 增泽过滤器polishing felt 抛光毡,抛光毛毡polishing woolen felt 研磨毛毡polishing drum 抛光筒,磨削滚筒polishing disk 抛光盘,抛光圆盘polishing crystal 晶体抛光crystal polishing tiles 抛晶砖polishing composition 抛光剂polishing barrel 抛光筒polished face 磨光石面polished surface 抛光面,精加工面polished diamond 抛光钻石,已抛磨的钻石polished diamond film 抛光金刚石薄膜polished die 抛光模polished glass 磨光玻璃polished section 磨光片,抛光片press finishing 推压精加工through product 筛下产品production machine 专用机床pyramid temperature tester 测温角锥pyrometer 高温计pyrometric cone 熔锥,测温锥cutting quality 切割质量quernstone 磨石radius attachment 磨圆角装置rated capacity 额定容量,额定功率refractoriness 耐火性,耐熔性regrind bit 重磨钻头regulating wheel 调节轮,导轮resin bond wheel 树脂结合剂砂轮resistor furnace 电阻炉normal sand 标准砂tabular crystal 片状晶体revolution mark 旋转标痕,切削痕迹shaping without stock removal非切屑成形,无屑成形sizematic internal grinder 自动定尺寸内圆磨床Rockwell Hardness 洛氏硬度Rockwell Hardness Number 洛氏硬度指数……爱锐网国际站定期分享:最新求购信息、磨料磨具行业常用英汉互译、海关HS码查询,国家代码查询、回复询盘技巧、最新国际行业资讯、小视频等,并为大家提供在线帮助服务。

砂轮的种类(英语含图)

砂轮的种类(英语含图)

砂轮的种类(英语含图)第一篇:砂轮的种类(英语含图)Sammy din 总结Grinding wheel砂轮认识砂轮,学习砂轮的英语表达砂轮主要的划分形式主要是三种:形状、结合剂和磨料。

一.分类1、形状分类① Straight wheel平行砂轮② Cylinder or wheel ring筒形砂轮或轮圈③ Tapered wheel 斜边砂轮(斜边京轮)(锥形砂轮)④ Straight cup wheel 杯形砂轮⑤ Taper cup wheel碗形砂轮⑥ Dish wheel碟形砂轮Saucer wheel蝶形砂轮2、磨料分类① Corundum grinding wheel刚玉砂轮A.BFA 棕刚玉砂轮B.WFA白刚玉砂轮② Silicon carbide 碳化硅(金刚砂)A.black silicon carbide黑碳化硅B.green silicon carbide 绿碳化硅③ Diamond wheel 金刚石砂轮④CBN(cubic boron nitride grinding wheel)立方氮化硼砂轮3、结合剂分类① Vitrified grinding wheel陶瓷砂轮② Resin bond wheel 树脂砂轮③ Rubber grinding wheel 橡胶砂轮④ Metal bond grinding wheel金属砂轮第二篇:PS3抠图基本种类Photoshop_CS3 基本种类2011-12-9抠图一、橡皮擦抠图方法、特点和适用范围:橡皮擦抠图就是用橡皮擦工具擦掉不用的部分,留下有用的部分。

这种方法属外形抠图的方法,简单好用,但处理效果不好,可用于外形线条简单的图形抠图。

但主要用于对其它方法抠图后的效果进行进一步处理。

操作步骤:1、打开图片;2、双击该图层,将背景层改为普通层;3、选取橡皮擦工具,可选画笔主直径大点,先粗略地擦掉大部分不用的部分4、再选画笔主直径小点,把图片放大,进行精细处理。

金属加工专业英语词汇

金属加工专业英语词汇

金属加工专业英语词汇abrasive belt|砂带[金属加工专业英语词汇]\r\nabrasive cut-off machine|砂轮切断机[金属加工专业英语词汇]\r\nabrasive dressing wheel|砂轮修整轮[金属加工专业英语词汇]\r\nabrasive grain|磨料粒度[金属加工专业英语词汇]\r\nabrasive lapping wheel|磨料研磨轮[金属加工专业英语词汇]\r\n accuracy of position|位置精度[金属加工专业英语词汇]\r\naccuracy to shape|形状精度[金属加工专业英语词汇]\r\nactive cutting edge|主切削刃[金属加工专业英语词汇]\r\nadapter flange|连接器法兰盘[金属加工专业英语词汇]\r\nadjointing flanks|共軛齿廓[金属加工专业英语词汇]\r\nangle milling cutter|角铣刀[金属加工专业英语词汇]\r\nangular milling|斜面铣削[金属加工专业英语词汇]\r\nangular plunge grinding|斜向切入磨削[金属加工专业英语词汇]\r\nangular turning|斜面车削[金属加工专业英语词汇]\r\nautomatic bar machine|棒料自动车床[金属加工专业英语词汇]\r\nautomatic boring machine|自动镗床[金属加工专业英语词汇]\r\nautomatic copying lathe|自动仿形车床[金属加工专业英语词汇]\r\nautomatic double-head milling machine|自动双轴铣床[金属加工专业英语词汇]\r\nautomatic lathe|自动车床[金属加工专业英语词汇]\r\nautomatic turret lathe|自动转塔车床[金属加工专业英语词汇]\r\nbelt grinding machine|砂带磨床[金属加工专业英语词汇]\r\nbench lathe|台式车床[金属加工专业英语词汇]\r\nbevel gear cutting machine|锥齿轮切削机床[金属加工专业英语词汇]\r\nbevel gear tooth system|锥齿轮系,锥齿轮传动系统[金属加工专业英语词汇]\r\nbevel|斜角,斜面,倾斜,斜切,斜角规,万能角尺,圆锥的,倾斜的,斜边,伞齿轮,锥齿轮[金属加工专业英语词汇]\r\nborehole|镗孔,镗出的孔,钻眼[金属加工专业英语词汇]\r\nboring fixture|镗孔夹具[金属加工专业英语词汇]\r\nboring machine|镗床[金属加工专业英语词汇]\r\nboring|镗孔,钻孔,穿孔[金属加工专业英语词汇]\r\nboring tool|镗刀[金属加工专业英语词汇]\r\nboringn and milling machine|镗铣床[金属加工专业英语词汇]\r\ndrilling and milling machine|镗铣床[金属加工专业英语词汇]\r\nbroaching machine|拉床,铰孔机,剥孔机[金属加工专业英语词汇]\r\nbroaching tool|拉刀[金属加工专业英语词汇]\r\nbroad finishing tool|宽刃精切刀,宽刃精车刀,宽刃光切刀[金属加工专业英语词汇]\r\ncam contour grinder|凸轮仿形磨床[金属加工专业英语词汇]\r\n carbide tip|硬质合金刀片[金属加工专业英语词汇]\r\ncarbide turning tool|硬质合金车刀[金属加工专业英语词汇]\r\n carbide-tipped tool|硬质合金刀具[金属加工专业英语词汇]\r\n cast iron machining|铸铁加工,铸铁切削加工[金属加工专业英语词汇]\r\ncenterless cylindrical grinder|无心外圆磨床[金属加工专业英语词汇]\r\nceramic cutting tool|金属陶瓷刀具[金属加工专业英语词汇]\r\n chamfer|倒角,倒棱[金属加工专业英语词汇]\r\nchamfered cutting edge|倒角刀刃[金属加工专业英语词汇]\r\n champ|焦急[金属加工专业英语词汇]\r\nchamping fixture|快换夹具[金属加工专业英语词汇]\r\nchamping jaw|快换卡爪[金属加工专业英语词汇]\r\nchaser|螺纹梳刀,梳刀盘,板牙[金属加工专业英语词汇]\r\nchatter|振动,振荡,震颤,刀振[金属加工专业英语词汇]\r\ncherry|樱桃,鲜红的,樱桃木制的[金属加工专业英语词汇]\r\nchip breaker groove radius|断屑槽底半径,卷屑槽底半径[金属加工专业英语词汇]\r\nchip clearance|切屑间隙[金属加工专业英语词汇]\r\nchip cross-sectional area|切屑横截面面积[金属加工专业英语词汇]\r\nchip curl|螺旋形切屑[金属加工专业英语词汇]\r\nchip flow|切屑流[金属加工专业英语词汇]\r\nchip formation|切屑形成[金属加工专业英语词汇]\r\nchip|切屑,铁屑,刀片,刀头,片,薄片,芯片,基片[金属加工专业英语词汇]\r\nchip removing process|去毛刺加工[金属加工专业英语词汇]\r\n chip variable|切屑变量[金属加工专业英语词汇]\r\nchuck|卡盘,夹盘,卡头,(电磁)吸盘, 固定,装卡,夹紧,卡住[金属加工专业英语词汇]\r\nchucker|卡盘车床,卡角车床[金属加工专业英语词汇]\r\ncircular drillling machine|圆工作台钻床[金属加工专业英语词汇]\r\ncircular path|环路,圆轨迹[金属加工专业英语词汇]\r\ncircular pitch measurement|周节测量[金属加工专业英语词汇]\r\ncircumference|圆周,周线,周界,周围,四周,范围[金属加工专业英语词汇]\r\nclose-grained|细颗粒的[金属加工专业英语词汇]\r\ncoeffecient of tool thrust|刀具推力系数[金属加工专业英语词汇]\r\ncoil chip|卷状切屑[金属加工专业英语词汇]\r\ncold circular saw|冷圆锯[金属加工专业英语词汇]\r\ncold saw|冷锯[金属加工专业英语词汇]\r\ncolumn drilling machine|圆(方)柱立式钻床[金属加工专业英语词汇]\r\ncombined drill and milling cutter|复合钻铣床[金属加工专业英语词汇]\r\ncomplete traverse grinding|横进给磨削,切入磨削[金属加工专业英语词汇]\r\ncomputer-controlled machine|计算机控制机床,数控机床[金属加工专业英语词汇]\r\ncontact pattern|靠模[金属加工专业英语词汇]\r\ncontinuous chip|连续切屑[金属加工专业英语词汇]\r\ncontinuous spiral chip|连续螺旋切屑[金属加工专业英语词汇]\r\ncontour grinding|仿形磨削,成形磨削[金属加工专业英语词汇]\r\ncontour milling|成形铣削,外形铣削,等高走刀曲面仿形法[金属加工专业英语词汇]\r\ncontour|轮廓,外形,外貌,轮廓线,回路,网路,电路,等高线,等值线,轮廓等高距仿形的,靠模的[金属加工专业英语词汇]\r\nconvex milling attachment|凸面铣削附件[金属加工专业英语词汇]\r\nconvex turning attachment|中凸车削附件,凸面车削附件[金属加工专业英语词汇]\r\ncoolant lubricant emulsion|冷却润滑乳液(剂)[金属加工专业英语词汇]\r\ncoolant lubricant|冷却润滑剂[金属加工专业英语词汇]\r\ncopy grinding|仿形磨床[金属加工专业英语词汇]\r\ncopy-mill|仿形铣[金属加工专业英语词汇]\r\ncopying turret lathe|仿形转塔车床[金属加工专业英语词汇]\r\n corner|弯(管)头[金属加工专业英语词汇]\r\ncrankshaft grinding machine|曲轴磨床[金属加工专业英语词汇]\r\ncrankshaft turning lathe|曲轴车床[金属加工专业英语词汇]\r\n creep feed grinding|缓进给磨削[金属加工专业英语词汇]\r\ncross milling|横向铣削[金属加工专业英语词汇]\r\ncurly chip|卷状切屑,螺旋形切屑,切屑螺旋[金属加工专业英语词汇]\r\ncut off|切断(开,去),关闭,停车,停止,断开装置,断流器,挡板,截止,截流[金属加工专业英语词汇]\r\ncut teeeth|铣齿[金属加工专业英语词汇]\r\ncut|切削(割),口,片,断,断开,削减,减少,断面,剖面,相交,凹槽[金属加工专业英语词汇]\r\ncut-off grinding|砂轮截断,砂轮切割[金属加工专业英语词汇]\r\n cutter|刀具,切削工具,截断器,切断器,切断机[金属加工专业英语词汇]\r\ncutting edge profile|切削刃轮廓(外形,断面),切削刃角度[金属加工专业英语词汇]\r\ncutting force|切削力[金属加工专业英语词汇]\r\ncutting lip|切削刃,刀刃,钻唇,钻刃[金属加工专业英语词汇]\r\ncutting|切削,切片,切割,切屑,金属屑,截槽[金属加工专业英语词汇]\r\ncutting operation|切削加工,切削操作,切削作业[金属加工专业英语词汇]\r\ncutting rate|切削效率,切削速率[金属加工专业英语词汇]\r\ncutting tool|刀具,切削工具,刃具[金属加工专业英语词汇]\r\ncycle|周期,周,循环,一个操作过程,轮转,自行车[金属加工专业英语词汇]\r\ncylindrical grinder|外圆磨床[金属加工专业英语词汇]\r\ndamage|损坏(害,伤,耗,失),破坏,事故,故障,伤害,危害[金属加工专业英语词汇]\r\ndeep-hole drilling|深孔钻削[金属加工专业英语词汇]\r\ndeep-hole milling|深孔铣削[金属加工专业英语词汇]\r\ndesign|设计,计算,计划,方案,设计书,图纸[金属加工专业英语词汇]\r\ndie-sinking|凹模[金属加工专业英语词汇]\r\ndimension|尺寸,尺度,维度,量纲,因次[金属加工专业英语词汇]\r\n direction of the feed motion|进给方向,进刀方向[金属加工专业英语词汇]\r\ndiscontinuous chip|间断切屑[金属加工专业英语词汇]\r\ndistance|距离,间隔(隙),长度, 隔开[金属加工专业英语词汇]\r\ndouble-column planer-miller|双柱龙门铣床[金属加工专业英语词汇]\r\ndress|修饰,修整,平整,整理,清理,装饰,调制,准备,打磨,磨光,压平,轿直,清洗,清理,分级[金属加工专业英语词汇]\r\ndrilling machine|钻床,钻机,钻孔机,打眼机[金属加工专业英语词汇]\r\ndrilling|钻头,钻床,穿孔器,凿岩机, 钻孔,打孔,钻井,钻探[金属加工专业英语词汇]\r\ndrilling tool|钻孔(削,井,眼)工具[金属加工专业英语词汇]\r\nedge point|刀口,刀刃[金属加工专业英语词汇]\r\nefficiency|效率,效能,性能,功率,产量,实力,经济性,有(功,实)效[金属加工专业英语词汇]\r\nend mill|立铣刀[金属加工专业英语词汇]\r\nexternal grinding|外圆磨削[金属加工专业英语词汇]\r\nface grinding machine|平面磨床[金属加工专业英语词汇]\r\nface milling machine|端面磨床[金属加工专业英语词汇]\r\nface|表面,外观,工作面,表盘,屏,幕面向,朝向,表面加工,把表面弄平[金属加工专业英语词汇]\r\nfeed force|进给力[金属加工专业英语词汇]\r\nfeed motion|进给运动[金属加工专业英语词汇]\r\nfine adjustment|精调,细调,微调[金属加工专业英语词汇]\r\nfine boring|精密镗孔[金属加工专业英语词汇]\r\nfinish|精加工,抛光,修整,表面粗糙度,完工,最后加工,最后阶段,涂层,涂料[金属加工专业英语词汇]\r\nfinish-cutting|精加工,最终切削[金属加工专业英语词汇]\r\nfixture|夹具,夹紧装置,配件,零件,定位器,支架[金属加工专业英语词汇]\r\nform|型式,类型,摸板,模型,形成,产生,成形,表格形(组,构)成,产生,作出,成形,造型[金属加工专业英语词汇]\r\nform-turn|成形车削[金属加工专业英语词汇]\r\nfree-cutting|自由切削,无支承切削,高速切削[金属加工专业英语词汇]\r\ngap|间隔,间隙,距离,范围,区间,缺口,开口火花隙, 使产生裂缝豁开[金属加工专业英语词汇]\r\ngear cutting machine|齿轮加工机床,切齿机[金属加工专业英语词汇]\r\ngear generating grinder|磨齿机[金属加工专业英语词汇]\r\ngear hob|齿轮滚刀[金属加工专业英语词汇]\r\ngrinding cutter|磨具[金属加工专业英语词汇]\r\ngrinding force|磨削力[金属加工专业英语词汇]\r\ngrinding machine|磨床[金属加工专业英语词汇]\r\ngrinding wheel diameter|砂轮直径[金属加工专业英语词汇]\r\ngrinding wheel width|砂轮宽度[金属加工专业英语词汇]\r\ngroove milling|铣槽[金属加工专业英语词汇]\r\ngroove|槽,切口,排屑槽,空心槽,坡口, 切(开,铣)槽[金属加工专业英语词汇]\r\nheadstock spindle|床头箱主轴,主轴箱主轴,头架轴[金属加工专业英语词汇]\r\nhelical tooth system|螺旋齿轮传动装置[金属加工专业英语词汇]\r\nhigh precision lathe|高精度车床[金属加工专业英语词汇]\r\nhigh-speed machining|高速加工[金属加工专业英语词汇]\r\nhigh-speed|高速[金属加工专业英语词汇]\r\nhob|齿轮滚刀,滚刀,螺旋铣刀, 滚铣,滚齿,滚削[金属加工专业英语词汇]\r\nhobbing machine|滚齿机,螺旋铣床,挤压制模压力机,反应阴模机[金属加工专业英语词汇]\r\nhole|孔,洞,坑,槽,空穴,孔道,管道, 钻(穿,冲,开)孔,打洞[金属加工专业英语词汇]\r\nhone |磨石,油石,珩磨头,磨孔器,珩磨,[金属加工专业英语词汇]\r\n honing machine|珩磨机,珩床,搪磨床,磨孔机,磨气缸机[金属加工专业英语词汇]\r\nhorsepower|马力[金属加工专业英语词汇]\r\ninclination|倾斜,斜度,倾角,斜角(坡),弯曲,偏(差,角)转[金属加工专业英语词汇]\r\nincrement|增量,增加,增(大)长[金属加工专业英语词汇]\r\nindexing table automatic|自动分度工作台[金属加工专业英语词汇]\r\ninfeed grinding|切入式磨削[金属加工专业英语词汇]\r\ninstallation|装置,设备,台,站,安装,设置[金属加工专业英语词汇]\r\ninternal grinding|内圆磨削[金属加工专业英语词汇]\r\ninvolute hob|渐开线滚刀[金属加工专业英语词汇]\r\njig boring machine|坐标镗床[金属加工专业英语词汇]\r\nkeyway cutting|键槽切削加工[金属加工专业英语词汇]\r\nknurling tool|滚花刀具,压花刀具,滚花刀[金属加工专业英语词汇]\r\nlaedscrew machine|丝杠加工机床[金属加工专业英语词汇]\r\n lap grinding|研磨[金属加工专业英语词汇]\r\nlapping|研磨,抛光,精研,搭接,擦准[金属加工专业英语词汇]\r\nlathe dog|车床轧头,卡箍,鸡心夹头,离心夹头,制动爪,车床挡块[金属加工专业英语词汇]\r\nlathe|车床[金属加工专业英语词汇]\r\nlathe tool|车刀[金属加工专业英语词汇]\r\nlevel|水平,水准,水平线,水平仪,水准仪,电平,能级,程度,强度, 水平的,相等的,均匀的,平稳的[金属加工专业英语词汇]\r\nloading time|装载料时间,荷重时间,充填时间,充气时间[金属加工专业英语词汇]\r\nlock|锁,栓,闸,闭锁装置,锁型,同步,牵引, 闭锁,关闭,卡住,固定,定位,制动刹住[金属加工专业英语词汇]\r\nlongitudinal grinding|纵磨[金属加工专业英语词汇]\r\nlow capacity machine|小功率机床(机器)[金属加工专业英语词汇]\r\nmachine axis|机床中心线[金属加工专业英语词汇]\r\nmachine table|机床工作台[金属加工专业英语词汇]\r\nmachine tool|机床,工作母机[金属加工专业英语词汇]\r\nmachining variable|加工变量[金属加工专业英语词汇]\r\ncutting variable|切削变量[金属加工专业英语词汇]\r\nmachining allowance|机械加工余量[金属加工专业英语词汇]\r\n machining cycle|加工循环[金属加工专业英语词汇]\r\nmachining|机械加工,切削加工[金属加工专业英语词汇]\r\nmachining of metals|金属切削加工,金属加工[金属加工专业英语词汇]\r\nmagazine automatic|自动化仓库,自动化料斗,自动存贮送料装置[金属加工专业英语词汇]\r\nmanufacture|制造者,生产者,厂商,产品,制造[金属加工专业英语词汇]\r\nmaterial removing rate|材料去除率[金属加工专业英语词汇]\r\n metal cutting|金属切削[金属加工专业英语词汇]\r\nmetal-cutting technology|金属切削工艺学,金属切削工艺(技术)[金属加工专业英语词汇]\r\nmetal-cutting tool|金属切削刀具,金属切削工具[金属加工专业英语词汇]\r\nmicrometer adjustment|微调[金属加工专业英语词汇]\r\nmilling feed|铣削进给,铣削走刀量,铣削走刀机构[金属加工专业英语词汇]\r\nmilling machine|铣床[金属加工专业英语词汇]\r\nmilling|铣削,磨碎,磨整,选矿[金属加工专业英语词汇]\r\nmilling spindle|铣床主轴[金属加工专业英语词汇]\r\nmilling tool|铣削刀具,铣削工具[金属加工专业英语词汇]\r\nmount|固定,安装,装配,装置,架设,n. 固定件,支架,座,装置,机构[金属加工专业英语词汇]\r\nmounting fixture|安装夹具,固定夹具[金属加工专业英语词汇]\r\nmounting|安装,装配,固定,机架,框架,装置[金属加工专业英语词汇]\r\nNose|鼻子,端,前端,凸头,刀尖,机头,突出部分,伸出部分[金属加工专业英语词汇]\r\nnumber of revolutions|转数[金属加工专业英语词汇]\r\nnumerical control|数字控制[金属加工专业英语词汇]\r\nnumerically controlled lathe|数控车床[金属加工专业英语词汇]\r\noblique grinding|斜切式磨床[金属加工专业英语词汇]\r\noperate|操纵,控制,运行,工作,动作,运算[金属加工专业英语词汇]\r\noperating cycle|工作循环[金属加工专业英语词汇]\r\noperation|运转,操作,控制,工作,作业,运算,计算[金属加工专业英语词汇]\r\noperational instruction|操作说明书,操作说明[金属加工专业英语词汇]\r\noperational safety|操作安全性,使用可靠性[金属加工专业英语词汇]\r\noscillating type abrasive cutting machine|摆动式砂轮切割机[金属加工专业英语词汇]\r\noscillation|振动,振荡,摆动,颤振,振幅[金属加工专业英语词汇]\r\n out-cut milling|切口铣削[金属加工专业英语词汇]\r\noxide ceramics|氧化物陶瓷[金属加工专业英语词汇]\r\noxide-ceramic cutting tool|陶瓷刀具[金属加工专业英语词汇]\r\nperformance|实行,执行,完成,特性,性能,成品,制作品,行为,动作,生产率,效率[金属加工专业英语词汇]\r\nperipheral grinding|圆周磨削[金属加工专业英语词汇]\r\nperipheral speed|圆周速度,周速,边缘速度[金属加工专业英语词汇]\r\nperpendicular|垂直的,正交的,成直角的 n. 垂直,正交,竖直,垂线,垂直面[金属加工专业英语词汇]\r\nphysical entity|实体,实物[金属加工专业英语词汇]\r\npitch circle|节圆[金属加工专业英语词汇]\r\npitch|齿距,节距,铆间距,螺距,极距,辊距,坡度,高跨比,俯仰角[金属加工专业英语词汇]\r\nplain milling machine|普通铣床[金属加工专业英语词汇]\r\ncylindrical milling machine|圆柱形铣床[金属加工专业英语词汇]\r\nplain grinding|平面磨削[金属加工专业英语词汇]\r\nplain turning|平面车床[金属加工专业英语词汇]\r\nplane milling|平面铣削[金属加工专业英语词汇]\r\nplane|平面,面,投影,刨,水平,程度,阶段,飞机平的弄平,整平,刨,飞行[金属加工专业英语词汇]\r\nplane-mill|平面铣刀,平面铣床[金属加工专业英语词汇]\r\nplunge mill|模向进给滚轧机[金属加工专业英语词汇]\r\nplunge-cut|切入式磨削,横向进给磨削,全面进刀法,全面进给法[金属加工专业英语词汇]\r\nplunge-cut thread grinder|切入式螺纹磨床[金属加工专业英语词汇]\r\nplunge-grinding|切入式磨削[金属加工专业英语词汇]\r\npoint|点,尖端,刀尖,针尖,指针,交点,要点,论点,特点指,面向,瞄准,对准,表明,弄尖,强调[金属加工专业英语词汇]\r\npower hacksaw|机动弓锯(钢锯)[金属加工专业英语词汇]\r\npower|功率,效率,能(容,力)量,动力,电源,能源驱(拖,带,发)动,给...以动力[金属加工专业英语词汇]\r\nprecision boring machine|精密镗床[金属加工专业英语词汇]\r\nprecision boring|精镗[金属加工专业英语词汇]\r\nprecision machining|精密机械加工[金属加工专业英语词汇]\r\n pressure angle|压力角[金属加工专业英语词汇]\r\nprimary cutting edge|主切削刃[金属加工专业英语词汇]\r\nprincipal feed motion|主进给运动,主进刀运动[金属加工专业英语词汇]\r\nproduction method|生产方法[式][金属加工专业英语词汇]\r\nprofile cutting tool|成形刀具,成形铣刀,定形刀具[金属加工专业英语词汇]\r\nprofile mill|仿形铣削,仿形机床[金属加工专业英语词汇]\r\nprofile|轮廓,形面,剖面,侧面图,分布图。

金属词汇中英日

金属词汇中英日

金属加工专业词中英对照Aabrasion n. 磨料,研磨材料,磨蚀剂, a. 磨损的,磨蚀的abrasive belt n. 砂带abrasive belt grinding n. 砂带磨削,用研磨带磨光abrasive cut-off machine n. 砂轮切断机abrasive dressing wheel n. 砂轮修整轮abrasive grain n. 磨料粒度abrasive grit n. 研磨用磨料,铁粒abrasive lapping wheel n. 磨料研磨轮accuracy of position n. 位置精度accuracy to shape n. 形状精度active cutting edge n. 主切削刃adapter flange n. 连接器法兰盘adjointing flanks n. 共軛齿廓align n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准angle milling cutter n. 角铣刀angular grinding n. 斜面磨削,斜磨法angular milling n. 斜面铣削angular plunge grinding n. 斜向切入磨削angular turning n. 斜面车削arbour n. 刀杆,心轴,柄轴,轴,辊轴attachment n. 附件,附件机构,联结,固接,联结法automatic bar machine n. 棒料自动车床automatic boring machine n. 自动镗床automatic copying lathe n. 自动仿形车床automatic double-head milling machine n. 自动双轴铣床automatic lathe n. 自动车床automatic turret lathe n. 自动转塔车床Bbelt grinding machine n. 砂带磨床bench lathe n. 台式车床bevel n. 斜角,斜面,倾斜,斜切,斜角规,万能角尺,圆锥的,倾斜的,斜边,伞齿轮,锥齿轮bevel gear cutting machine n. 锥齿轮切削机床bevel gear tooth system n. 锥齿轮系,锥齿轮传动系统borehole n. 镗孔,镗出的孔,钻眼boring n. 镗孔,钻孔,穿孔boring fixture n. 镗孔夹具boring machine n. 镗床boring tool n. 镗刀boring, drilling and milling machine n. 镗铣床broaching machine n.拉床,铰孔机,剥孔机broaching tool n. 拉刀broad finishing tool n. 宽刃精切刀,宽刃精车刀,宽刃光切刀CCalibrate vt. 校准[正],刻度,分度,检查[验],定标,标定,使标准化,使符合标准cam contour grinder n. 凸轮仿形磨床carbide tip n. 硬质合金刀片carbide turning tool n. 硬质合金车刀carbide-tipped tool n. 硬质合金刀具cast iron machining n. 铸铁加工,铸铁切削加工centerless cylindrical grinder n. 无心外圆磨床ceramic cutting tool n. 金属陶瓷刀具chamfer n.;vt. 倒角,倒棱chamfered cutting edge n. 倒角刀刃champ v. 焦急champing fixture n. 快换夹具champing jaw n. 快换卡爪chaser n. 螺纹梳刀,梳刀盘,板牙chatter vi.;n. 振动,振荡,震颤,刀振cherry n.;a. 樱桃,鲜红的,樱桃木制的chip n. 切屑,铁屑,刀片,刀头,片,薄片,芯片,基片chip breaker groove radius n. 断屑槽底半径,卷屑槽底半径chip clearance n. 切屑间隙chip cross-sectional area n. 切屑横截面面积chip curl n. 螺旋形切屑chip flow n. 切屑流chip formation n. 切屑形成chip removing process n. 去毛刺加工chip variable n. 切屑变量chuck n. 卡盘,夹盘,卡头,[电磁]吸盘,vt. 固定,装卡,夹紧,卡住chucker n. 卡盘车床,卡角车床circular drillling machine n. 圆工作台钻床circular path n. 环路,圆轨迹circular pitch measurement n. 周节测量circumference n. 圆周,周线,周界,周围,四周,范围close-grained a. 细颗粒的coeffecient of tool thrust n. 刀具推力系数coil chip n. 卷状切屑cold circular saw n. 冷圆锯cold saw n. 冷锯column drilling machine n. 圆[方]柱立式钻床combined drill and milling cutter n. 复合钻铣床complete traverse grinding n. 横进给磨削,切入磨削computer-controlled machine n. 计算机控制机床,数控机床contact pattern n. 靠模continuous chip n. 连续切屑continuous spiral chip n. 连续螺旋切屑contour n. 轮廓,外形,外貌,轮廓线,回路,网路,电路,等高线,等值线,轮廓等高距 a. 仿形的,靠模的contour grinding n. 仿形磨削,成形磨削contour milling n. 成形铣削,外形铣削,等高走刀曲面仿形法convex milling attachment n. 凸面铣削附件convex turning attachment n. 中凸车削附件,凸面车削附件coolant lubricant n. 冷却润滑剂coolant lubricant emulsion n. 冷却润滑乳液[剂]copy n. 样板,仿形,靠模工作法,拷贝复制品,v. 复制,模仿,抄录copy grinding n. 仿形磨床copy-mill n. 仿形铣copying turret lathe n. 仿形转塔车床corner n. 角,弯[管]头,弯管counterbore n. 埋头孔,沉孔,锥口孔,平底扩孔钻,平底锪钻, n.;vt. 扩孔,锪孔,镗孔,镗阶梯孔crankshaft grinding machine n. 曲轴磨床crankshaft turning lathe n. 曲轴车床creep feed grinding n. 缓进给磨削cross milling n. 横向铣削curly chip n. 卷状切屑,螺旋形切屑,切屑螺旋cut v.;n. 切削[割],口,片,断,断开,削减,减少,断面,剖面,相交,凹槽cut off n. 切断[开,去],关闭,停车,停止,断开装置,断流器,挡板,截止,截流cut teeeth n. 铣齿cut-off grinding n. 砂轮截断,砂轮切割cutter n. 刀具,切削工具,截断器,切断器,切断机cutting n. 切削,切片,切割,切屑,金属屑,截槽cutting edge profile n. 切削刃轮廓[外形,断面],切削刃角度cutting force n. 切削力cutting lip n. 切削刃,刀刃,钻唇,钻刃cutting operation n. 切削加工,切削操作,切削作业cutting rate n. 切削效率,切削速率cutting tool n. 刀具,切削工具,刃具cycle n. 周期,周,循环,一个操作过程,轮转,自行车cylindrical grinder n. 外圆磨床Ddamage n.;vt. 损坏[害,伤,耗,失],破坏,事故,故障,伤害,危害deep-hole drilling n.深孔钻削deep-hole milling n. 深孔铣削design n. 设计,计算,计划,方案,设计书,图纸die-sinking n. 凹模dimension n. 尺寸,尺度,维度,量纲,因次direction of the feed motion n. 进给方向,进刀方向discontinuous chip n. 间断切屑distance n. 距离,间隔[隙],长度,vt. 隔开double-column planer-miller n. 双柱龙门铣床dress v. 修饰,修整,平整,整理,清理,装饰,调制,准备,打磨,磨光,压平,轿直,清洗,清理,分级drilling n. 钻头,钻床,穿孔器,凿岩机,v. 钻孔,打孔,钻井,钻探drilling machine n. 钻床,钻机,钻孔机,打眼机drilling tool n. 钻孔[削,井,眼]工具Eedge point n. 刀口,刀刃efficiency n. 效率,效能,性能,功率,产量,实力,经济性,有[功,实]效end mill n. 立铣刀external grinding n. 外圆磨削Fface n. 表面,外观,工作面,表盘,屏,幕v. 面向,朝向,表面加工,把表面弄平face grinding machine n. 平面磨床face milling machine n. 端面磨床feed force n. 进给力feed motion n. 进给运动fine adjustment n. 精调,细调,微调fine boring n. 精密镗孔finish v.;n. 精加工,抛光,修整,表面粗糙度,完工,最后加工,最后阶段,涂层,涂料finish-cutting n. 精加工,最终切削fixture n. 夹具,夹紧装置,配件,零件,定位器,支架form n. 型式,类型,摸板,模型,形成,产生,成形,表格v. 形[组,构]成,产生,作出,成形,造型form-turn n. 成形车削free-cutting n. 自由切削,无支承切削,高速切削Ggap n. 间隔,间隙,距离,范围,区间,缺口,开口火花隙,vt. 使产生裂缝vi. 豁开gear cutting machine n. 齿轮加工机床,切齿机gear generating grinder n. 磨齿机gear hob n. 齿轮滚刀grinding cutter n. 磨具grinding force n. 磨削力grinding machine n. 磨床grinding wheel diameter n. 砂轮直径grinding wheel width n. 砂轮宽度groove n. 槽,切口,排屑槽,空心槽,坡口,vt. 切[开,铣]槽groove milling n.铣槽Hheadstock spindle n. 床头箱主轴,主轴箱主轴,头架轴helical tooth system n. 螺旋齿轮传动装置high precision lathe n. 高精度车床high-speed n. 高速high-speed machining n. 高速加工hob n. 齿轮滚刀,滚刀,螺旋铣刀,v. 滚铣,滚齿,滚削horsepower n. 马力hobbing machine n. 滚齿机,螺旋铣床,挤压制模压力机,反应阴模机hole n. 孔,洞,坑,槽,空穴,孔道,管道,v. 钻[穿,冲,开]孔,打洞hone n. vt. 磨石,油石,珩磨头,磨孔器,珩磨,honing machine n. 珩磨机,珩床,搪磨床,磨孔机,磨气缸机Iinclination n. 倾斜,斜度,倾角,斜角[坡],弯曲,偏[差,角]转increment n. 增量,增加,增[大]长indexing table automatic n. 自动分度工作台infeed grinding n. 切入式磨削installation n. 装置,设备,台,站,安装,设置internal grinding n. 内圆磨削involute hob n. 渐开线滚刀Jjig boring machine n. 坐标镗床Kkeyway cutting n. 键槽切削加工knurling tool n. 滚花刀具,压花刀具,滚花刀Llaedscrew machine n. 丝杠加工机床lap grinding n. 研磨lapping n. 研磨,抛光,精研,搭接,擦准lathe n. 车床lathe dog n. 车床轧头,卡箍,鸡心夹头,离心夹头,制动爪,车床挡块lathe tool n. 车刀level n. 水平,水准,水平线,水平仪,水准仪,电平,能级,程度,强度,a. 水平的,相等的,均匀的,平稳的loading time n. 装载料时间,荷重时间,充填时间,充气时间lock n. 锁,栓,闸,闭锁装置,锁型,同步,牵引,v. 闭锁,关闭,卡住,固定,定位,制动刹住longitudinal grinding n. 纵磨low capacity machine n. 小功率机床[机器]Mmachine axis n. 机床中心线machine table n. 机床工作台machine tool n. 机床,工作母机machining n. 机械加工,切削加工machining (or cutting) variable n. 加工(或切削)变量machining allowance n. 机械加工余量machining cycle n. 加工循环machining of metals n. 金属切削加工,金属加工magazine automatic n. 自动化仓库,自动化料斗,自动存贮送料装置manufacture n. 制造者,生产者,厂商,产品,制造material removing rate n. 材料去除率metal cutting n. 金属切削metal-cutting technology n. 金属切削工艺学,金属切削工艺[技术]metal-cutting tool n. 金属切削刀具,金属切削工具micrometer adjustment n. 微调milling n. 铣削,磨碎,磨整,选矿milling feed n. 铣削进给,铣削走刀量,铣削走刀机构milling machine n. 铣床milling spindle n. 铣床主轴milling tool n. 铣削刀具,铣削工具mount v. 固定,安装,装配,装置,架设,n. 固定件,支架,座,装置,机构mounting n. 安装,装配,固定,机架,框架,装置mounting fixture n. 安装夹具,固定夹具NNose n. 鼻子,端,前端,凸头,刀尖,机头,突出部分,伸出部分number of revolutions n. 转数numerical control n. 数字控制numerically controlled lathe n. 数控车床Ooblique grinding n. 斜切式磨床operate v. 操纵,控制,运行,工作,动作,运算operating cycle n. 工作循环operation n. 运转,操作,控制,工作,作业,运算,计算operational instruction n. 操作说明书,操作说明operational safety n. 操作安全性,使用可靠性oscillating type abrasive cutting machine n. 摆动式砂轮切割机oscillation n. 振动,振荡,摆动,颤振,振幅out-cut milling n. 切口铣削oxide ceramics n. 氧化物陶瓷oxide-ceramic cutting tool n. 陶瓷刀具Pperformance n. 实行,执行,完成,特性,性能,成品,制作品,行为,动作,生产率,效率peripheral grinding n. 圆周磨削peripheral speed n. 圆周速度,周速,边缘速度perpendicular a. 垂直的,正交的,成直角的n. 垂直,正交,竖直,垂线,垂直面physical entity n. 实体,实物pitch n. 齿距,节距,铆间距,螺距,极距,辊距,坡度,高跨比,俯仰角pitch circle n. 节圆plain (or cylindrical) milling machine n. 普通(或圆柱形)铣床plain grinding n. 平面磨削plain turning n. 平面车床plane n. 平面,面,投影,刨,水平,程度,阶段,飞机 a.平的v. 弄平,整平,刨,飞行plane milling n. 平面铣削plane-mill n. 平面铣刀,平面铣床plunge mill n. 模向进给滚轧机plunge-cut n. 切入式磨削,横向进给磨削,全面进刀法,全面进给法plunge-cut thread grinder n. 切入式螺纹磨床plunge-grinding n. 切入式磨削point n. 点,尖端,刀尖,针尖,指针,交点,要点,论点,特点v. 指,面向,瞄准,对准,表明,弄尖,强调power n. 功率,效率,能[容,力]量,动力,电源,能源v. 驱[拖,带,发]动,给...以动力power hacksaw n. 机动弓锯[钢锯]precision boring n. 精镗precision boring machine n. 精密镗床precision machining n. 精密机械加工pressure angle n. 压力角primary cutting edge n. 主切削刃principal feed motion n. 主进给运动,主进刀运动production method s n. 生产方法[式]profile n. 轮廓,形面,剖面,侧面图,分布图。

机械工具英文名称

机械工具英文名称

机械工具英文名称引言机械工具是将人的力量转化为机械能力的工具,广泛应用于各行各业,是许多行业的重要助手。

在现代社会中,英语已成为全球通用的语言,掌握机械工具的英文名称对于提高沟通效率、扩大工作领域具有重要意义。

本文将介绍一些常见机械工具的英文名称,帮助读者更好地掌握工作中的英语词汇。

1. 扳手•Adjustable wrench - 可调节扳手•Open-end wrench - 实心端口扳手•Combination wrench - 十字插孔扳手•Allen wrench - 内六角扳手•Socket wrench - 套筒扳手•Torque wrench - 扭力扳手2. 锤子•Claw hammer - 叉子锤•Ball-peen hammer - 圆头锤•Sledgehammer - 大锤•Rubber mallet - 橡胶木槌•Dead blow hammer - 无反冲锤3. 螺丝刀•Flathead screwdriver - 平头螺丝刀•Phillips screwdriver - 十字螺丝刀•Allen screwdriver - 内六角螺丝刀•Torx screwdriver - 星形螺丝刀•Precision screwdriver - 精密螺丝刀4. 钳子•Pliers - 钳子•Needle-nose pliers - 尖嘴钳•Vice grips - 平口钳•Wire strippers - 剥线钳•Locking pliers - 锁紧钳5. 锯子•Hand saw - 手锯•Hacksaw - 脚锯•Coping saw - 储备架子•Circular saw - 圆锯•Reciprocating saw - 往复锯6. 钻头•Twist drill bit - 齿锥钻头•Masonry drill bit - 砖头钻头•Spade drill bit - 扁锥钻头•Forstner drill bit - 福斯特纳钻头•Hole saw - 孔锯7. 磨具•Grinding wheel - 砂轮•Diamond wheel - 金刚石砂轮•Sanding disc - 砂纸片•Flap disc - 翻盖砂轮•Wire brush - 钢丝刷8. 测量工具•Tape measure - 卷尺•Level - 水平仪•Caliper - 卡尺•Micrometer - 千分尺•Laser distance measure - 激光测距仪9. 钻孔工具•Power drill - 电钻•Impact driver - 冲击钻•Hammer drill - 锤钻•Rotary hammer - 旋锤钻•Core drill - 钻孔机10. 气动工具•r compressor - 气压机•Pneumatic drill - 气动钻•r impact wrench - 气动冲击扳手•r grinder - 气动磨光机•r nler - 气动钉枪结论本文介绍了一些常见机械工具的英文名称,包括扳手、锤子、螺丝刀、钳子、锯子、钻头、磨具、测量工具、钻孔工具和气动工具。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

此词汇适合外贸人员开展业务、技术人员查阅文献、生产人员、磨削、磨床人员生产中查阅对照。

abrasive 磨料abrasive grain 磨粒angle of repose 安息角artificial abrasive 人造磨料black fused alumina 黑刚玉black silicon carbide 黑碳化硅boron carbide 碳化硼brown fused alumina 棕刚玉bulk density 堆积密度capillarity 毛细现象combination grain size 混合粒度compressive strength 抗压强度conventional abrasive 普通磨料cubic boron nitride 立方氮化硼cubic silicon carbide 立方碳化硅diamond 金刚石emery 天然金刚砂fused alumina 电熔刚玉garnet 石榴石grain size 粒度grain size distribution 粒度组成green silicon carbide 绿碳化硅grit designation 粒度号impact toughness 冲击韧性losse grain 自由磨粒macrograins 粗磨粒magnetic material 磁性物metal clad diamond 金属衣金刚石microcrystalline fused alumina 微晶刚玉microgrits 微粉monocrystalline fused alumina 单晶刚玉natural abrasive 天然磨料natural corundum 天然刚玉natural diamond 天然金刚石physical corundum 物理刚玉pink fused alumina 絡刚玉〔粉刚玉〕polycrystal 多晶体polycrystalline cubic boron nitride 立方氮化硼烧结体polycrystalline diamond 人造金刚石烧结体silicon carbide 碳化硅single crystal 单晶体sintered alumina 烧结刚玉specific surface area 比外表积super abrasive 超硬材料synthetic diamond 人造金刚石white fused alumina 白刚玉zirconia alumina 锆刚玉abrasive belts 砂带abrasive cloth 砂布abrasive cloth belts 布砂带abrasive cloth in rolls 卷状砂布abrasive cloth in sheets 页状砂布abrasive discs 砂盘abrasive paper 砂纸abrasive paper belts 纸砂带abrasive paper in rolls 卷状砂纸abrasive paper in sheets 页状砂纸abrasive products 磨具abrasive sleeves 砂套adhesive 粘结剂aluminium oxide sintered stick 烧结刚玉魔石aluminium oxide sintered wheel 烧结刚玉砂轮backing 基材balancing test 平衡试验tbond 结合剂bonded abrasive products 固结磨具brick’s stick 磨石butt joint belts 对接砂带centreless grinding wheel 无心磨砂轮centreless regulating wheel 无心磨导轮closed coat 密植砂closed pore 闭口气孔closed porosity 闭口气孔率closed backing 布基coated abrasives 涂附磨具combination backing 复合基combination backing abrasive belts 复合基砂带combination stone 双面磨石concentration 浓度cubic boron nitride abrasive products 立方氮化硼磨具cubic boron nitride grinding wheel 立方氮化硼砂轮CBN section 立方氮化硼层cutting off wheel 切断砂轮cylindrical abrasive sleeves 筒形砂套cylinder wheel 筒形砂轮deep cut and creep feed grinding wheel; 深切缓进给砂轮density of coating grain 植砂密度depressed center wheel 钹形砂轮diamond abrasive products 金刚石磨具diamond beads 金刚石串珠diamond circular saw blades 金刚石圆锯片diamond cut-off wheel 金刚石切割砂轮diamond edging wheel 金刚石磨边砂轮diamond dressing roller 金刚石滚轮diamond cylinderi wheel 金刚石筒形砂轮diamond finishing pellets 金刚石精磨片diamond frame saw blades 金刚石框架锯条diamond grinding wheel 金刚石砂轮diamond section 金刚石石层diamond saw segments 锯齿diamond sawing and cutting tool 金刚石锯切工具diamond wire saw 金刚石绳锯diluent 稀释剂dish wheel 蝶形砂轮dispersing agent 分散剂dulling 钝化dynamic balance test 动平衡试验electroplated diamond inner slicing disc 电镀金刚石内圆切割锯片electroplated diamond files 电镀金刚石什锦锉electroplated metal bond 电镀金属结合剂electroplated super abrasive products 电镀超硬磨料磨具endless abrasive belts 无接头砂带fibre backing 钢纸基flap wheels 研磨页轮flap wheels with flange 卡盘研磨叶轮flap wheels with shaft 带轴研磨叶轮form grinding wheel 成型砂轮fused bond 烧熔结合剂glue bond 动物胶粘结剂grade 硬度grinding segments 砂瓦grinding wheel 砂轮grinding wheel for rice husking 碾米砂轮grinding wheel steel balls 磨钢球砂轮grinding wheel peripheral speed 〔砂轮〕工作速度grindstone 天然磨石high-pressure snagging wheel 重负荷修磨砂轮high-speed grinding wheel 高速砂轮honing stick 衍磨条hubbed wheel 单面凸砂轮inorganic bond 无机结合剂intermediate section 过渡层joint abrasive belts 接头砂带lap joint belts 搭接砂带lapping compound 研磨剂lapping paste 研磨膏liquid lapping compound 研磨液magnesia bond 菱苦土结合剂magnesia grindstone菱苦土磨石maximum operating speed 砂轮最高工作速度metal bond 金属结合剂metallographic abrasive paper 金相砂纸mounted cone, curved side 椭圆磨头mounted plug, flat end 圆柱磨头mounted plug, round end 半球形磨头mounted wheel 磨头oil soluble lapping paste 油溶性研磨膏open coat 疏植砂open pore 开口气孔open porosity 开口气孔率organic bond 有机结合剂paper backing 纸基percentage of grain 磨粒率pore 气孔pressure sensitive backing discs 粘贴砂盘pulp segment 纸浆磨块pulp stone 纸浆磨石PVA (polyvinylalcohol) grinding wheel PVA 砂轮resinoid bond 树脂结合剂resin over glue bond 半树脂粘结剂resin over resin bond 全树脂粘结剂revolving strength 回转强度rotation test 回转试验rubber bond 橡胶结合剂self-sharpening 自锐性shellac bond 虫胶结合剂sintered bond 烧结结合剂sintering metal bond 烧结金属结合剂solid lapping compound 固体研磨剂special purpose wheels 专用砂轮static balance test 静平衡试验straight cup wheel 杯形砂轮straight wheel 平形砂轮structure 组织substrate 基体super abrasive section 超硬磨料层super abrasive products 超硬磨料磨具super finishing stick 超精油石support 载体taper cup wheel 碗形砂轮tapered wheel 斜边砂轮thin grinding wheel 薄片砂轮threaded insert disk 螺栓紧固平形砂轮total porosity 总气孔率true density 真密度truncated cone abrasive sleeves 截锥砂套tumbling chip abrasives 滚抛磨块unbalance 不平衡unbalance 不平衡量unbalance value 不平衡值vitrified bond 陶瓷结合剂volume density 体积密度water absorption 吸水率waterproof abrasive cloth 耐水砂布waterproof abrasive cloth belts 耐水布砂带waterproof abrasive paper 耐水砂纸waterproof abrasive paper belts 耐水纸砂带waterproof bond 耐水粘结剂water soluble lapping paste 水溶性研磨膏wheel relieved and recessed both side 双面凹带锥砂轮wheel relieved and recessed same side 单面凹带锥砂轮wheel recessed one side 单面凹砂轮wheel recessed two side 双面凹砂轮worm grinding wheel 蜗杆砂轮第11 页。

相关文档
最新文档