模具专业英语术语

合集下载

模具专业术语英语

模具专业术语英语

模具专业术语英语
模具专业涉及许多专业术语,在英语中对应的词汇如下:
1. Mold/Mould: 模具
2. Die: 模具,尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴,注塑道
6. Gate: 浇口,进料口
7. Ejector Pin: 顶针,用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽,模具凹槽
这些词汇在模具制造和加工过程中经常使用,涵盖了模具设计、制造和加工等方面的专业术语。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner流道电脑分析:mold flow analysis流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert 行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语一、图纸制图用术语英语基准: datum公差: tolerance尺寸:dimension圆角: fillet半径:radius曲线: curve公称直径:nominal diameter正方形:square直线度:straightness平面度:flatness圆度:roundness圆柱度:cylindricity线轮廓度:profile of line面轮廓度:profile of surface平行度:parallelism位置公差:position tolerance垂直度:perpendicularity周围标志:all around symbol倾斜度:angularity同轴度:coaxlality同心度:concentricity对称度: symmetry位置度:position圆跳动:run out全跳动: total run out最大材料状态:maximum material condition (MMC)最小材料状态: least material condition (LMC)不论大小的特征:no symbol regardless of feature size (RFS)投影公差区:projected tolerance zone切平面: tangent plane自由状态的变化:free state variations基本尺寸:basic dimension参考尺寸:reference dimension基准特征:datum feature尺寸源:dimension origin特征控制框:feature control frame圆锥锥度: conical taper斜坡度:slope沉孔或忽孔: counter bore/ spot face埋头孔:countersink深度:depth相同的地方:number of places电弧长度:arc length厚度:thickness球面半径:SR spherical radius均布:EQS球面直径公差值:SØ spherical diameter 控制半径:CR controlled radius45度倒角: 45 chamfer之间-表明:between统计公差:statistical tolerance基准目标:datum target靶点: target point公称厚度:nominal thickness图纸中常用术语:交界面:interface冲压工艺试验:stamping process pilot 防错工艺:POKA YOKE process翻领:collar单向的:unidirectional理论重量:theoretical weight分段区:segment定位孔:pilot hole缺陷:defect氧化:oxidation毛刺:burr税利边缘:sharp edges刀痕:tool marks闪点:flashing褶皱:wrinkles开裂:crack/splitting撕裂:tear老化:aging间隙:gap压伤:crush刮伤:scratch擦伤:scratch拉伤:abrasion划伤:scoring变形:deformation缺料:short shot挤料:extrusion deformation打磨严重:serious grinding尺寸不良:out-of-size锈斑:rust麻点:pit油脂:grease/lubricants/oil模具:tooling / die/ mold/ mould检具:checking fixture/ gauge工装:fixture三坐标测量: coordinate measuring machine简易模:plain die连续模:progressive die传递模:transfer die复合模:gang die型腔母模:mould cavity模芯公模:mould core上模板:下模板:上垫板:下垫板:冲压:stamping冲孔:pierce落料/下料:blank成型:form整型:restrike切边:trim折弯:bend翻边:flange翻孔:extrude卷耳:curling导向:pilot压筋:bead压凸台:emboss空步:idle回折:tip back拉深:draw剪边:shear铆合:rivet印字:stamp marker压印:coin压平: stretch切断:cut off切开:split切舌:lance斜楔:cam模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples 插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connectorplug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing 中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector 阴连接器Housing阳连接器wafer 线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould 冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould 动模movable mould, movable half 上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

模具专业英文术语大全

模具专业英文术语大全

模具专业英文术语大全模具英语专业术语模具述语一、入水:gate进入位:gate locati on水口形式:gate type 大水口:edge gate 纟田水口:pin-point gate水口大小:gate size 转水口:s witchi ng runn er/gate唧嘴口径:sprue diameter二、流道:runner热流道:hot runn er,hot mani fold热嘴冷流道:hot sprue/cold runner 唧嘴直流:direct sprue gate 圆形流道:rou nd (full/half ru nner 流道电脑分析:mold flow an alysis流道平衡:runner balanee 热嘴:hot sprue 热流道板:hot man ifold 发热管:cartridge heater 探针:thermocouples 插头:conn ector plug 插座:conn ector socket 密封/封料:seal三、运水:water line 喉塞:line lpug 喉管:tube塑胶管:plastic tube 快速接头:jiffy quick conn ector plug/socker四、模具零件:mold comp onents 三板模:3-plate mold二板模:2-plate mold 边钉/ 导边:leader pin/guide pin 边司/ 导套:bushi ng/guide bush ing 中托司:shoulder guide bush ing 中托边L: guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝:screw 管钉:dowel pin开模槽:ply bar scot 内模管位:core/cavity in ter-lock 顶针:ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):n ylon latch lock斜顶:lifter 模胚(架):mold base 上内模:cavity in sert 下内模:core insert 行位(滑块):slide 镶件:in sert 压座/斜鸡:wedge 而寸磨板/油板:wedge wear plate 压条:plate 撑头:support pillar 唧嘴:sprue bush ing 挡板:stop plate 定位圈:locati ng ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretu n 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spri ng rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞:pipe plug锁模块:lock plate 斜顶:an gle from pin 斜顶杆:an gle ejector rod 尼龙拉勾:part ing locks 活动臂:lever arm 复位键、提前回杆:early return bar气阀:valves 斜导边:an gle pin 术语:terms承压平面平衡:part ing surface supportbala nee模排气:part ing line ven ti ng回针碰料位:retur n pin and cavityin terfere nee模总高超岀啤机规格:mold base shuthight顶针碰运水:water line in terfereswithejector pin料位岀上/下模:part from cavith (core) side 模胚原身岀料位:cavity direct cut on A- plate,core direct cut on B-plate.不准用镶件:Do n ot use (core/cavity)in sert用铍铜做镶件:use beryllium copperin sert初步(正式)模图设计:preliinary (final) mold desig n反呵:reverse core弹弓压缩量:spri ng compressed len gth稳定性好:good stability,stable 强度不够:in sufficie nt rigidity 均匀冷去卩:eve n cooli ng 扣模:stick ing 热膨胀:thero expa nsion 公差:tolora nee 铜公(电极):copper electrode Mold & die comp onents 模具单元Mold cha nging systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair模具维修Molds模具Press ing dies 压模Quick die cha nge systems 速换模系统Quick mold cha nge systems 快速换模系统三、模具塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base定模座板Top clamping plateTop plateFixed clamp plate 水口推板stripper plate A 板 A plateB 板B plate 支承板support plate 方铁spacer plate 底针板ejector plate 面针板ejector retainer plate 回针Retur n pin 导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush 动模座板Bottom clamp plate Mov ing clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss 合模力mould clamping force 锁模力mould locking force 挤岀extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parti ng line定模stationary mould ,Fixed mould 动模movable mould, movable half 上模upper mould ,upper half 下模lower mould ,lower half 型腔cavity凹模cavity plate ,cavity block拼块split定位销dowel定位销孑L dowel hole型芯core斜销an gle pin, fin ger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core 螺纹型芯threaded core热流道模具hot-ru nner mould 绝热流道模insulated runner mould 熔合纹weld line (flow line ) 三板式模具three plate mould 脱模ejection换模腔模具interchangeable cavity mould 脱模剂release age nt 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould , cavity block 阳模male mould电加工设备Electro n Discharge Machi ning 数控加工中心CNC machi ne cen ter 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine 去磁机Demagnetization machine 万能摇臂钻床Uni versal radial movable driller 立式钻床Vertical driller 超声波清洗机Ultras onic cleari ng machi ne compre sio n moldi ng 压缩成型flash mold溢流式模具plsitive mold 挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak 仿皮革shiver饰纹flow mark 流痕weldi ng mark 溶合痕post screw in sert 螺纹套筒埋值self tapp ing screw 自攻螺丝striper plate 脱料板piston活塞cylinder汽缸套chip细碎物han dle mold 手持式模具(移转成型用模具)en capsulati on moldi ng 低压圭寸装成型(射岀成型用模具)two plate两极式(模具)well type 蓄料井in sulated runner 绝缘浇道方式hot runner 热浇道runner plat浇道模块valve gate 阀门浇口band heater环带状的电热器spindle 阀针spear head 刨尖头slag well冷料井cold slag冷料渣air vent排气道weldi ng line 熔合痕eject pin 顶岀针knock pin顶岀销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orie ntati on 定向sprue gate 射料浇口,直浇口nozzle射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate 隔膜浇口ring gate环形浇口subari ne gate 潜入式浇口tu nnel gate 隧道式浇口pin gate针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣emboss 凸点dome 凸圆semi-sheari ng 半剪stamp mark 冲记号deburr or coin 压毛边punch riveti ng 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark n earside 正面压印tick-mark farside 反面压印冲压名称类exte nsion dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thick ness 料片厚度factor系数upward 向上dow nward 向下upper plate 上模板lower plate 下模板die pad下垫板die holder 下夹板die set下模座bottomblock 下垫脚bottom plate下托板(底板)strippingplate 内外打(脱料板) outer stripper 夕卜脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch冲头insert入块(嵌入件)deburri ng punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller滚轴baffle plate 挡块located block 定位块support ing block for locati on定位支承块air cushi on plate 气垫板air-cushi on eject-rod 气垫顶杆trim ming punch 切边冲子stiffe ning rib punch = st in ger 力廿强筋冲子ribb on punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板slidi ng block 滑块塑料模具专业术语动模movable mould movi ng half 定模座板fixed clamp plate, top clampi ng plate. top plate动模座板movi ng clamp plate. bottom clampi ng plate. bottom plate上模座板upper clamp ing plate下模座板lower clampi ng plate 凹模固定板cavity-reta inerplate型芯固定板core-reta iner plate凸模固定板pun ch-reta iner plate模套chase. bolster. frame支承板back ing plate. supprr plate垫块spacer parallel支架ejector hous ing. mould base leg 压力铸造模具die-casti ng diepress specificati on 冲床规格die height range 适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guid ing post 内导柱inner hexago n screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin顶料销eq-height sleeves=spool 等高套筒pin销lifter guide pin 浮升导料销guide pin 导正销wire spri ng 圆线弹簧outer guid ing post 夕卜导柱stop screw 止付螺丝located pin 定位销outer bush 夕卜导套模板类top plate上托板(顶板)top block上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad脱料背板up stripper 上脱料板male die 公模(凸模) feature die 公母模female die 母模(凹模)。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner流道电脑分析:mold flow analysis流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert 行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

[整理]模具英语专业术语

[整理]模具英语专业术语

模具(MOULD/MOLD,TOOL):CAVITY:前模CORE:后模(定模)DIMENSION:寸法GATE:浇口/水口/入水口PIN GATE:点水口/点浇入水SIDE GATE:边水口/侧浇入水/大水口APPERANCE SURFACE:体裁面WARPAGE DIRECTION:变形方向DRAFT ANGEL:脱模斜度PARTING LINE/P。

L:分模线EJECT PIN/E。

P:注塑顶针BLAST/TEXTURE:喷啥,蚀纹MIRROR FINISH:镜面(抛光)处理POLISH:抛光EMD:放电加工WELD:熔接加工(烧焊)LATHE:车床MILLING CUTTER:铣刀MILLING MACHINE:铣床WIRE CUT:线切割CNC:主加工中心POWER DRILL:电钻DRILLING:钻孔FRITING:烧结ANNEALING:淬火注塑术语(INJECTION)SCREW:螺杆WELD LINE:熔接线SINK MARK:缩水DRAG MARK:脱花BURR:批锋FLOW MARK:流纹SHADOW MARK/GLOSS DIFFERENCE:光影SHORT:缺胶INJECTION CYCLE:成型周期注塑英语型厚大小Thick size锁模结构(机绞/直压)Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式(电动五点,油压五点,油压十三点)Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质(合金)Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量(理论)Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式(全自动/全液压)Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程,open ould stroke定产,order production定产效率,efficiency of order prod uction注胶切换点,glue-injection switching point保压压力1,protective pressure倒索,inverse sling模保护,mould protection关模低压,close mould low pressure炮筒温度,gun barrel temperature回料量,returning amount注射压力,injecting pressure色母配比,raw color ratio mixing配套摸具,matched mold顶针次数,thimble times立式注胶机vertical injector工艺卡,WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x%减少…含量…%Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模:Injection mould热塑性塑料注射模:Injection mould for thermoplasctics 热固性塑料注射模:Injection mould for thermosets无流道模:Runerless mould热流道模:Hot runner mould绝热流道模:Insulated温流道模:Warm runner mould2. 浇注,排溢,分型浇注系统:Feed system主流道:Sprue分流道:Runner浇口:Gate直接浇口:Direct gate ;Sprue gate环行浇口:Ring gate盘型浇口:Disk gate ;Diaphragm轮辐浇口:Spoke gate :Spider gate点浇口:Pin-point gate侧浇口:Edge gate潜伏浇口:Submarine gate护耳浇口:Tab gate扇型浇口:Fan gate 牛角浇口:Horn gate冷料穴:Cold-slug well浇口套:Sprue bush ;Sprue bushing浇口镶块:Gating insret分流锥:Sprader流道板:Runner plate热流道板:Manifold block;Hot-runner manifold温流道板:Warm runner plate二级喷嘴:Secondary nozzle鱼雷形组合体:Torpedo;T orpedo body assembly管式加热器:Cartridge heater热管:Heat pipe阀式浇口:Valve gate加热腔:Loading chamber柱塞:Force plunger;Pot plungr溢料槽:Flash grorve ;Spew grovve排气槽:Vent分型面:Parting line水平分型面:Horizontal parting half垂直分型面:Vertical parting half3. 成型零件定模:Stationary mould:Fixed half动模;Movable mould ;Moving half上模:Upper mould;Upper half下模:Lower mould :Lower half型腔:Cavity凹模:Impression;Cavity plate镶件:Mould insert活动镶件:Movable insert;Lose detail拼块:Splits凹模拼块:Cavity splits型芯拼块:Core splits型芯:Core侧型芯:Side core:slide core螺纹型芯:Thread plug;Threaded core螺纹型环:Thread ring;Threaded cavity凸模:Punch;Force嵌件:Insert for mould4. 支持与固定零件定模座板:Fixed clamp plate:Top clamping plate;Top plate动模座板:Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板:Upper clamping plate下模座板:Lower clamping plate凹模固定板:Cavity-retaier plate型芯固定板:Core-retaier plate凸模固定板:Punch-retaier pilte模套:Chase ;Bolster;Frame;支撑板:Backing plate垫块:Spacer parallel支架:Ejector housing支撑柱:Support pillar模板:Mould plate5. 抽芯零件斜销:Angle pin; Finger cam滑块:Slide;Cam slide侧型芯滑块:Slide core-slide滑块导板:Slide guide strip锲紧块:Heel block;Wedge block;Locking heel斜槽导板:Finger guide plate弯销:Dog-leg cam斜滑块:Angled-lift splits6. 导向零件导柱:Guide pillar;Guide pin;Leader pin带头导柱:Guide pillar ;Straight leader pin带肩导柱:Guide pillar Shouldered;Shoulder leader pin推板导柱:Ejector guide pillar;Ejeector guide pin导套:Guide bush ;Guide bushing直导套:Guide bush ;Straight ;Straight bushing带头导套:Guide bush ;Shoulder bushing推板导套:Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈:Locating ring锥形定位圈:Mould bases locating elements复位杆:Ejector plate return pin;Push-back pin限位钉:Stop pin;Stop button限位块:Stop block ;Stop pad定距拉杆:Length bolt;Puller bolt定距拉板:Puller plate;Limit plate8. 推出零件推杆:Ejector pin圆柱头推杆:Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管:Ejector sleeve推块:Ejector pad推件板:Stripper plate推件环:Stripper ring;Stripper dlisk推杆固定板:Ejector retainer plate推板:Ejector plate;Ejection plate连接推杆:Ejector tie rod 拉料杆:Sprue puller钩形垃料杆:Sprue puller ;Z-shaped球头垃料杆:Sprue puller;Ball headed圆锥头垃料杆:Sprue puller;Conical headed分流道垃料杆:Runner puller;Runner lock pin推流道板:Runner stripper plate9. 冷却和加热零件冷却通道:Cooling channel;Cooling line隔板:Baffle加热板:Heating plate隔热板:Thermal insulation board10. 模架模架:Mould base标准模架:Standard mould base11. 塑料成型模具的主要设计要素注射能力:Shot capacity收缩率:Shrinkage注射压力:Injection pressure锁模力:Clamping force ;Locking force成型压力:Moulding pressure模内压力:Internal mould pressure;Cavity pressure 开模力:Mould opening force脱模力:Ejection force抽芯力:Core-pulling force抽芯距:Core-pulling distance闭合高度:Mould shut height最大开距:Maximum daylight;Open daylight投影面积:Projected area脱模斜度:Draft脱模距:Stripper distance。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner流道电脑分析:mold flow analysis流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert 行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

模具专业的英语词汇大全

模具专业的英语词汇大全

模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇,我们可以看到模具行业不仅涉及具体的技术和操作,还包括了管理、质量控制、认证以及未来的发展趋势。

模具专业英文术语大全

模具专业英文术语大全

模具专业英文术语大全1. Die - 模具2. Mold - 模具3. Cavity - 型腔4. Core - 芯子5. Ejector pin - 顶杆6. Land - 分型面7. Gate - 浇口8. Filleting - 去毛刺9. Trim - 修整10. Draft - 拔模斜度11. Undercut - 底切12. Flash - 飞边13. Warpage - 翘曲14. Shrinkage - 收缩15. Melt flow rate - 熔融指数16. Injection molding - 注塑成型17. Blow molding - 吹塑成型18. Compression molding - 压缩成型19. Vacuum molding - 真空成型20. Overmolding - 包覆成型21. Co-injection molding - 双色注塑成型22. Gas assist injection molding - 气体辅助注塑成型23. Rotational molding - 旋转成型24. Injection compression molding - 注射压缩成型25. Injection blow molding - 注射吹塑成型26. Injection stretch blow molding - 注射拉伸吹塑成型27. Injection transfer molding - 注射传递成型28. Injection foam molding - 注射发泡成型29. Injection gas assisted rotational molding - 注射气体辅助旋转成型30. Injection compression blow molding - 注射压缩吹塑成型31. Injection stretch blow molding - 注射拉伸吹塑成型32. Injection transfer blow molding - 注射传递吹塑成型33. Injection foam blow molding - 注射发泡吹塑成型34. Injection gas assisted transfer molding - 注射气体辅助传递成型35. Injection compression foam molding - 注射压缩发泡成型36. Injection stretch foam molding - 注射拉伸发泡成型37. Injection transfer foam molding - 注射传递发泡成型38. Injection gas assisted foam blow molding - 注射气体辅助发泡吹塑成型39. Injection compression foam blow molding - 注射压缩发泡吹塑成型40. Injection stretch foam blow molding - 注射拉伸发泡吹塑成型41. Injection transfer foam blow molding - 注射传递发泡吹塑成型42. Injection gas assisted compression molding - 注射气体辅助压缩成型43. Injection gas assisted stretch blow molding - 注射气体辅助拉伸吹塑成型44. Injection gas assisted transfer blow molding - 注射气体辅助传递吹塑成型45. Injection gas assisted foam compression molding - 注射气体辅助发泡压缩成型46. Injection gas assisted foam stretch blow molding - 注射气体辅助发泡拉伸吹塑成型47. Injection gas assisted foam transfer blow molding - 注射气体辅助发泡传递吹塑成型48. Injection gas assisted compression foam molding - 注射气体辅助压缩发泡成型49. Injection gas assisted stretch foam blow molding - 注射气体辅助拉伸发泡吹塑成型50. Injection gas assisted transfer foam blow molding - 注射气体辅助传递发泡吹塑成型51. Mold temperature control system - 模具温度控制系统52. Coolant system - 冷却系统53. Ejector system - 顶出系统54. Feed system - 喂料系统55. Packaging machine - 包装机56. Automated guided vehicle (AGV) - 自动导引车(AGV)57. Robotic arm - 机械臂58. Computer numerical control (CNC) machine - 计算机数控(CNC)机床59. Plastics injection machine - 塑料注塑机60. Plastics extruder - 塑料挤出机61. Plastics blow molding machine - 塑料吹塑机62. Plastics injection compression molding machine -塑料注塑压缩成型机63. Plastics injection stretch blow molding machine - 塑料注塑拉伸吹塑成型机64. Plastics injection transfer molding machine - 塑料注塑传递成型机65. Plastics injection foam molding machine - 塑料注塑发泡成型机66. Plastics injection gas assisted rotational molding machine - 塑料注塑气体辅助旋转成型机67. Plastics injection compression foam molding machine - 塑料注塑压缩发泡成型机68. Plastics injection stretch foam molding machine - 塑料注塑拉伸发泡成型机69. Plastics injection transfer foam molding machine - 塑料注塑传递发泡成型机70. Plastics injection gas assisted foam blow molding machine - 塑料注塑气体辅助发泡吹塑成型机71. Plastics injection compression foam blow molding machine - 塑料注塑压缩发泡吹塑成型机72. Plastics injection stretch foam blow molding machine - 塑料注塑拉伸发泡吹塑成型机73. Plastics injection transfer foam blow moldingmachine - 塑料注塑传递发泡吹塑成型机74. Plastics injection molding machine with movable platen - 带活动模板的塑料注塑机75. Plastics injection molding machine with fixed platen - 带固定模板的塑料注塑机76. Plastics injection molding machine with hot runner system - 带热流道系统的塑料注塑机77. Plastics injection molding machine with cold runner system - 带冷流道系统的塑料注塑机78. Plastics injection molding machine with multi-cavity design - 带多腔设计的塑料注塑机79. Plastics injection molding machine with clamping force control - 带夹紧力控制的塑料注塑机80. Plastics injection molding machine with cycle time reduction - 带循环时间缩短的塑料注塑机81. Plastics injection molding machine with energy saving features - 带节能功能的塑料注塑机82. Plastics injection molding machine with high precision control - 带高精度控制的塑料注塑机83. Plastics injection molding machine with automatic tool changing system - 带自动换模系统的塑料注塑机84. Plastics injection molding machine with roboticautomation - 带机器人自动化的塑料注塑机85. Plastics injection molding machine with quality control system - 带质量管理系统的塑料注塑机86. Plastics injection molding machine with process monitoring system - 带工艺监控系统的塑料注塑机87. Plastics injection molding machine with maintenance reminder system - 带维护提醒系统的塑料注塑机88. Plastics injection molding machine with data logging and analysis - 带数据记录和分析的塑料注塑机89. Plastics injection molding machine with remote control and monitoring - 带远程控制和监控的塑料注塑机90. Plastics injection molding machine with safety features - 带安全功能的塑料注塑机91. Plastics injection molding machine with operator interface - 带操作员界面的塑料注塑机92. Plastics injection molding machine with easy cleaning system - 带易清洁系统的塑料注塑机93. Plastics injection molding machine with quick change tooling - 带快速换模装置的塑料注塑机94. Plastics injection molding machine with low noiseoperation - 带低噪音运行的塑料注塑机95. Plastics injection molding machine with high throughput capacity - 带高产量能力的塑料注塑机96. Plastics injection molding machine with energy recovery system - 带能量回收系统的塑料注塑机97. Plastics injection molding machine with environmental protection features - 带环保功能的塑料注塑机98. Plastics injection molding machine with advanced materials compatibility - 带先进材料兼容性的塑料注塑机99. Plastics injection molding machine with customizable options - 可定制选项的塑料注塑机100. Plastics injection molding machine with reliable performance and durability - 具有可靠性能和耐用性的塑料注塑机。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语一、图纸制图用术语英语基准: datum公差: tolerance尺寸:dimension圆角: fillet半径:radius曲线: curve公称直径:nominal diameter正方形:square直线度:straightness平面度:flatness圆度:roundness圆柱度:cylindricity线轮廓度:profile of line面轮廓度:profile of surface平行度:parallelism位置公差:position tolerance垂直度:perpendicularity周围标志:all around symbol倾斜度:angularity同轴度:coaxlality同心度:concentricity对称度: symmetry位置度:position圆跳动:run out全跳动: total run out最大材料状态:maximum material condition (MMC)最小材料状态: least material condition (LMC)不论大小的特征:no symbol regardless of feature size (RFS)投影公差区:projected tolerance zone切平面: tangent plane自由状态的变化:free state variations基本尺寸:basic dimension参考尺寸:reference dimension基准特征:datum feature尺寸源:dimension origin特征控制框:feature control frame圆锥锥度: conical taper斜坡度:slope沉孔或忽孔: counter bore/ spot face埋头孔:countersink深度:depth相同的地方:number of places电弧长度:arc length厚度:thickness球面半径:SR spherical radius均布:EQS球面直径公差值:SØ spherical diameter 控制半径:CR controlled radius45度倒角: 45 chamfer之间-表明:between统计公差:statistical tolerance基准目标:datum target靶点: target point公称厚度:nominal thickness图纸中常用术语:交界面:interface冲压工艺试验:stamping process pilot 防错工艺:POKA YOKE process翻领:collar单向的:unidirectional理论重量:theoretical weight分段区:segment定位孔:pilot hole缺陷:defect氧化:oxidation毛刺:burr税利边缘:sharp edges刀痕:tool marks闪点:flashing褶皱:wrinkles开裂:crack/splitting撕裂:tear老化:aging间隙:gap压伤:crush刮伤:scratch擦伤:scratch拉伤:abrasion划伤:scoring变形:deformation缺料:short shot挤料:extrusion deformation打磨严重:serious grinding尺寸不良:out-of-size锈斑:rust麻点:pit油脂:grease/lubricants/oil模具:tooling / die/ mold/ mould检具:checking fixture/ gauge工装:fixture三坐标测量: coordinate measuring machine简易模:plain die连续模:progressive die传递模:transfer die复合模:gang die型腔母模:mould cavity模芯公模:mould core上模板:下模板:上垫板:下垫板:冲压:stamping冲孔:pierce落料/下料:blank成型:form整型:restrike切边:trim折弯:bend翻边:flange翻孔:extrude卷耳:curling导向:pilot压筋:bead压凸台:emboss空步:idle回折:tip back拉深:draw剪边:shear铆合:rivet印字:stamp marker压印:coin压平: stretch切断:cut off切开:split切舌:lance斜楔:cam模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples 插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connectorplug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing 中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut on A-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg 压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材 khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector 阴连接器Housing阳连接器wafer 线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould 冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould 动模movable mould, movable half 上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

最全的模具英语专业术语(超级实用)

最全的模具英语专业术语(超级实用)

模具专业英语出模: mould unloading, mold stripping 出模角 : Draft Angle出模方向: The direction of the mold Mold Parting Direction入水: gate 进入位: gate location水口形式: gate type 大水口: edge gate细水口: pin-point gate 水口大小: gate size转水口: switching runner/gate 唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道: round(full/half runner流道电脑分析:mold flow analysis 流道平衡: runner balance热嘴: hot sprue 热流道板: hot manifold发热管: cartridge heater 探针: thermocouples插头: connector plug 插座: connector socket密封/封料: seal三、运水:water line喉塞: line lpug 喉管: tube塑胶管: plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components三板模: 3-plate mold 二板模: 2-plate mold边钉/导边:l eader pin/guide pin 边司/导套: bushing/guide bushing 中托司: shoulder guide bushing 中托边L: guide pin顶针板: ejector retainner plate 托板: support plate螺丝: screw 管钉: dowel pin开模槽: ply bar scot 内模管位: core/cavity inter-lock顶针: ejector pin 司筒: ejector sleeve司筒针: ejector pin 推板: stripper plate缩呵: movable core,return core core puller扣机(尼龙拉勾): nylon latch lock 斜顶: lifter模胚(架): mold base 上内模: cavity insert下内模: core insert 行位(滑块): slide镶件: insert 压座/斜鸡: wedge耐磨板/油板: wedge wear plate 压条: plate撑头: support pillar 唧嘴: sprue bushing挡板: stop plate 定位圈: locating ring锁扣: latch 扣鸡: parting lock set推杆: push bar 栓打螺丝: S.H.S.B顶板: eracuretun 活动臂: lever arm分流锥: spure sperader 水口司: bush垃圾钉: stop pin 隔片: buffle弹弓柱: spring rod 弹弓: die spring中托司: ejector guide bush 中托边: ejector guide pin镶针: pin 销子: dowel pin波子弹弓: ball catch模具成形不良用语英汉对照aberration 色差 atomization ? 化bank mark ? 料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡 blooming 起霜low hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮折叠 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ? 泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模机械类常用英语:冲压模具-零件类Punch 冲头 insert 入块(嵌入件)deburring punch 压毛边冲子 groove punch 压线冲子stamped punch 字模冲子 round punch 圆冲子special shape punch 异形冲子 bending block 折刀roller 滚轴 baffle plate 挡块located block 定位块 supporting block for location 定位支承块air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆trimming punch 切边冲子 stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子 reel-stretch punch 卷圆压平冲子guide plate 定位板 sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板lower sliding plate 下滑块板 upper holder block 上压块upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板bushing block 衬套 cover plate 盖板guide pad 导料块模具工程常用词汇英汉对照——3high-speed transmission 高速传递 heat dissipation 热传rack 上料 degrease 脱脂rinse 水洗 alkaline etch 龄咬desmut 剥黑膜 D.I. rinse 纯水次Chromate 铬酸处理 Anodize 阳性处理Seal 封孔 Revision 版次part number/P/N 料号 good products 良品scraped products 报放心品 defective products 不良品finished products 成品 disposed products 处理品barcode 条码 flow chart 流程表单assembly 组装 stamping 冲压molding 成型 spare parts=buffer 备品coordinate 座标 dismantle the die 折模auxiliary fuction 辅助功能 poly-line 多义线heater band 加热片 thermocouple 热电偶sand blasting 喷沙 grit 砂砾derusting machine 除锈机 degate 打浇口dryer 烘干机 induction 感应induction light 感应光 response=reaction=interaction 感应ram 连杆 edge finder 巡边器concave 凸 convex 凹short 射料不足 nick 缺口speck 瑕?? Shine 亮班splay 银纹 gas mark 焦痕delamination 起鳞 cold slug 冷块blush 导色 gouge 沟槽;凿槽satin texture 段面咬花 witness line 证示线patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机cushion 缓冲 magnalium 镁铝合金magnesium 镁金 metal plate 钣金lathe 车 mill 锉plane 刨 grind 磨drill 铝 boring 镗blinster 气泡 fillet 镶;嵌边through-hole form 通孔形式 voller pin formality 滚针形式cam driver 铡楔 shank 摸柄crank shaft 曲柄轴 augular offset 角度偏差velocity 速度 production tempo 生产进度现状torque 扭矩 spline=the multiple keys 花键quenching 淬火 tempering 回火annealing 退火 carbonization 碳化alloy 合金 tungsten high speed steel 钨高速的moly high speed steel 钼高速的 organic solvent 有机溶剂bracket 小磁导 liaison 联络单volatile 挥发性 resistance 电阻ion 离子 titrator 滴定仪beacon 警示灯 coolant 冷却液crusher 破碎机模具工程常用词汇英汉对照——2stock age analysis sheet 库存货龄分析表 on-hand inventory 现有库存available material 良品可使用 obsolete material 良品已呆滞to be inspected or reworked 待验或重工 total 合计cause description 原因说明 part number/ P/N 料号type 形态 item/group/class 类别quality 品质 prepared by 制表notes 说明 physical inventory 盘点数量year-end physical inventory difference analysis sheet 年终盘点差异分析表physical count quantity 帐面数量 difference quantity 差异量cause analysis 原因分析 raw materials 原料materials 物料 finished product 成品semi-finished product 半成品 packing materials包材disposed goods 处理品 warehouse/hub 仓库on way location 在途仓 oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓 skid/pallet 栈板tox machine 自铆机 wire EDM 线割EDM放电机coil stock 卷料 sheet stock 片料tolerance 工差 score=groove 压线cam block 滑块 pilot 导正筒trim 剪外边 pierce 剪内边drag form 压锻差 pocket for the punch head 挂钩槽slug hole 废料孔 feature die 公母模expansion dwg 展开图 radius 半径shim(wedge) 楔子 torch-flame cut 火焰切割set screw 止付螺丝 form block 折刀stop pin 定位销 round pierce punch=die button 圆冲子shape punch=die insert 异形子 stock locater block 定位块under cut=scrap chopper 清角 active plate 活动板baffle plate 挡块 cover plate 盖板male die 公模 female die 母模groove punch 压线冲子 air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板 bushing block 衬套insert 入块 club car 高尔夫球车capability 能力 parameter r参数factor 系数 phosphate 皮膜化成viscosity 涂料粘度 alkalidipping 脱脂main manifold 主集流脉 bezel 斜视规blanking 穿落模 dejecting 顶固模demagnetization 去磁;消磁模具钢材及零件英语模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 硅钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板塑件&模具相关英文compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕 post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物 handle mold 手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式(模具)well type 蓄料井 insulated runner 绝缘浇道方式hot runner 热浇道 runner plat 浇道模块valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头slag well 冷料井 cold slag 冷料渣air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mmwelding line 熔合痕 eject pin 顶出针knock pin 顶出销 return pin 回位销反顶针sleave 套筒 stripper plate 脱料板insert core 放置入子 runner stripper plate 浇道脱料板guide pin 导销 eject rod (bar) (成型机)顶业捧subzero 深冷处理 three plate 三极式模具runner system 浇道系统 stress crack 应力电裂orientation 定向 sprue gate 射料浇口,直浇口nozzle 射嘴 slag well 冷料井side gate 侧浇口 edge gate 侧缘浇口tab gate 搭接浇口 film gate 薄膜浇口flash gate 闸门浇口 slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mmdiaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口pin gate 针点浇口 Φ0.8~1.0mm Runner less 无浇道(sprue less) 无射料管方式 long nozzle 延长喷嘴方式Sprue 浇口;溶渣 sprue lock pin 料头钩销(拉料杆)塑件模具相关英文——2eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleave 套筒stripper plate 脱料板 insert core 放置入子runner stripper plate 浇道脱料板 guide pin 导销eject rod (bar) (成型机)顶业捧 subzero 深冷处理three plate 三极式模具 runner system 浇道系统stress crack 应力电裂 orientation 定向sprue gate 射料浇口,直浇口 nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井塑件模具相关英文——1compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕 post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物 handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具hot runner 热浇道 runner plat 浇道模块band heater 环带状的电热器 spindle 阀针spear head 刨尖头 cold slag 冷料渣模具相关英语——7Embosss 凸点 dome 凸圆semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印五金零件类inner guiding post 内导柱 inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱模具工程类plain die 简易模 pierce die 冲孔模forming die 成型模 progressive die 连续模gang dies 复合模 shearing die 剪边模riveting die 铆合模 pierce 冲孔forming 成型(抽凸,冲凸) draw hole 抽孔bending 折弯 trim 切边101个热处理常用英文词汇1. indication 缺陷2. test specimen 试样3. bar 棒材4. stock 原料5. billet 方钢,钢方坯6. bloom 钢坯,钢锭7. section 型材 8. steel ingot 钢锭9. blank 坯料,半成品 10. cast steel 铸钢11. nodular cast iron 球墨铸铁 12. ductile cast iron 球墨铸铁13. bronze 青铜 14. brass 黄铜15. copper 合金 16. stainless steel 不锈钢17. decarburization 脱碳 18. scale 氧化皮19. anneal 退火 20. process anneal 进行退火21. quenching 淬火 22. normalizing 正火23. Charpy impact text 夏比冲击试验 24. fatigue 疲劳25. tensile testing 拉伸试验 26. solution 固溶处理27. aging 时效处理 28. Vickers hardness 维氏硬度29. Rockwell hardness 洛氏硬度 30. Brinell hardness 布氏硬度31. hardness tester 硬度计 32. descale 除污,除氧化皮等33. ferrite 铁素体 34. austenite 奥氏体35. martensite 马氏体 36. cementite 渗碳体37. iron carbide 渗碳体 38. solid solution 固溶体39. sorbite 索氏体 40. bainite 贝氏体41. pearlite 珠光体 44. grain 晶粒42. nodular fine pearlite/ troostite 屈氏体 45. chromium 铬43. black oxide coating 发黑 46. cadmium 镉47. tungsten 钨 48. molybdenum 钼49. manganese 锰 50. vanadium 钒52. silicon 硅 53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷 55. nitrided 氮化的56. case hardening 表面硬化,表面淬硬 57. air cooling 空冷58. furnace cooling 炉冷 59. oil cooling 油冷60. electrocladding /plating 电镀 61. brittleness 脆性62. strength 强度 63. rigidity 刚性,刚度64. creep 蠕变 65. deflection 挠度66. elongation 延伸率 67. yield strength 屈服强度68. elastoplasticity 弹塑性 69. metallographic structure 金相组织70. metallographic test 金相试验 71. carbon content 含碳量72. induction hardening 感应淬火 73. impedance matching 感应淬火74. hardening and tempering 调质 75. crack 裂纹76. shrinkage 缩孔,疏松 77. forging 锻(件)78. casting 铸(件) 79. rolling 轧(件)80. drawing 拉(件) 81. shot blasting 喷丸(处理)82. grit blasting 喷钢砂(处理) 83. sand blasting 喷砂(处理)84. carburizing 渗碳 85. nitriding 渗氮86. ageing/aging 时效 87. grain size 晶粒度88. pore 气孔 89. sonim 夹砂90. cinder inclusion 夹渣91. lattice 晶格93. spectrum analysis 光谱分析 94. heat/thermal treatment 热处理95. inclusion 夹杂物 96. segregation 偏析97. picking 酸洗,酸浸 98. residual stress 残余应力99. remaining stress 残余应力 101. stress relief 应力释放100. relaxation of residual stress 消除残余应力92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性模具相关英语(5)semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印冲压名称类extension dwg 展开图 procedure dwg 工程图die structure dwg 模具结构图 material 材质material thickness 料片厚度 factor 系数upward 向上 downward 向下press specification 冲床规格 die height range 适用模高die height 闭模高度 burr 毛边gap 间隙 weight 重量total wt. 总重量 punch wt. 上模重量五金零件类inner guiding post 内导柱 inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱 stop screw 止付螺丝located pin 定位销 outer bush 外导套模板类top plate 上托板(顶板) top block 上垫脚punch set 上模座 punch pad 上垫板punch holder 上夹板 stripper pad 脱料背板up stripper 上脱料板 male die 公模(凸模)feature die 公母模 female die 母模(凹模)upper plate 上模板 lower plate 下模板die pad 下垫板 die holder 下夹板die set 下模座 bottom block 下垫脚bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板 inner stripper 内脱料板lower stripper 下脱料板注塑模部分中英文对照塑料成形模具 mould for plastics热塑性塑料模 mould for thermoplastics热固性塑料模 mould for thermosets压缩模 compression mould压注模、传递模 transfer mould注射模 injection mould热塑性塑料注射模 injection mould for thermoplastics热固性塑料注射模 injection mould for thermoses序号中文英语日语港台俗称定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg中文查英文:英语查中文根据国家标准,以下为部分压铸模具术语的标准翻译。

模具英语专业术语

模具英语专业术语

模具英语专业术语如下:1. 模具:Mold,Die2. 模具设计:Mold Design3. 模具制造:Mold Manufacturing4. 模具工程师:Mold Engineer5. 模具材料:Mold Material6. 耐磨材料:wear-resistant material7. 热处理:Heat Treatment8. 水路设计:Water Path Design9. 浇注系统:Injection Sleeve10. 冷却系统:Cooling System11. 顶出系统:Pop-out System12. 复位系统:Reset System13. 导向机构:Guide Device14. 模板:Base Plate15. 顶杆:Pushrod16. 复位杆:Reset Rod17. 斜导柱:Oblique Guide Column18. 导套:Guide Bushing19. 滑块:Slider20. 镶针:Pillow Block21. 弹簧:Spring22. 皮囊弹簧:Kelvin Spring23. 油压缓冲器:Hydraulic Buffer24. 压力表:Pressure Gauge25. 安全阀:Safety Valve26. 水路板:Waterway Plate27. 分流器:Flow Divider28. 水口:Filler Port29. 冷料穴:Cold Molding Chamber30. 模具钢:Mold Steel31. SKH-55、SKH-55M、高速工具钢、HSS等。

32. SKD、SKH-S、SKD61、SKH-9等。

模具钢硬度(Hardness of die steel):布氏硬度(HB)、洛氏硬度(HRC)、维氏硬度(HV)等。

33. SKD61(级硬SKD61) ,Cr12MoV,A3,A2,SKH-9,718,738,P20等。

塑料模具钢有PXZ、SACD、S136、S718、SS446、3Cr2Mo等。

模具专业英语词汇

模具专业英语词汇

Injection Mold Technical Terms(一)模具专业基本用词Professional Terms1.塑料—plastic, resin2.样件—sample3.钢料—steel4.注塑机—injection machine, press5.产品—part, product, moulding6.模具—mold, mould, toolA 简易模(样板模)—prototype moldB 量产用模具—production mold 7.三维造型(数模)—3D model, 3D data8.二维产品图—2D part drawing9.设计—design10.制造—manufacture, build up, construction11.检验—check, inspection12.测量—measure, inspection13.修改—change, modify, correction14.工程更改—engineer change15.质量—quality16.数量—quantity17.基准—datum, reference牛角入水-rads gate(二)如何解析2D 产品图?How to read 2D part drawing?一.产品几何Geometry1.点—point2.线(边)—line, edge3.面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4.壁厚—wall thickness, stock thickness5.加强筋(骨位)—rib6.孔—hole7.细长的槽—slot8.柱位—boss9.角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner 10.斜度—angle, taper11. 凹槽—recess , groove二.分模信息Splitting1.分型线—parting line (P/L), splitting line2.主分模方向—main direction, line of draw3.浇口设定—gating产品标识Part Identification1.产品名称—part name (P/N)2.产品编号+版本号—part number + revision (Rev.)3.型腔号—cavity number4.材料标记—material symbol5.模具编号—mold number (no.)6.日期印—dating insert, date code7.循环印—cycling code8.公司标志—company logo三.技术要求Specification (Special Requirement)1.项目启动表Kick-off sheet1)项目名称—program name, project name2)产品名称—part name, product name, part description3)产品编号—part number (P/N)4)客户模号—customer mold no.5)项目启动日期—kick off date, start date6)项目完成日期—due date,lead time7)内模件用钢—tool steel8)型腔数量—number of cavities9)数据文件编号—data file no.10)注塑材料—resin, plastic, raw material11)收缩率—shrink, shrinkage, shrink factor12)注塑机吨位—molding machine size, injection machine size 13)成型周期—cycle time14)型腔光洁度—cavity polish15)型芯光洁度—core polish16)皮纹(晒纹)—texture, grain17)拔模斜度—draft angle, removal taper18)注塑件颜色及光泽—molded color & gloss19)模具加工地—manufacturing facility20)热流道供应商—manifold manufacturer, manifold supplier 21)浇口位置—gate location / position22)浇口类型—gate type23)产品标识—stamp information, part identification24)特殊要求—special instructions25)安全模数—safe steel2.产品质量及外观要求Part Quality & Appearance Requirement1)尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受(合格)—accept, OK⑧拒绝(不合格)—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2)产品缺陷(常见的)Defects (normal)①缩水—sink mark, shrinkage②飞边,毛边—flash, burr③段差—mismatch discrepancy④银丝纹,蛇纹—snake marks, streak⑤弯曲,变形—warpage, distortion⑥打不饱(缺料)—short shot⑦熔接线—weld line⑧多胶—unwanted plastic⑨拉伤—damage3.产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4.常用词汇、词组及短语Normal Word, Short Sentence1)单边—per side2)双边—both sides3)加入,添加—add, incorporate4)去除,取消—remove, cancel5)满足…的要求,符合,与…要求一致—according to, conform to, satisfy, meet 6)要求,需要—require, need, demand7)确认—be approved, agreed by …8)允许—permit, allow9)在…范围之内—within10)不可以,不允许,禁止—free from, prevent, avoid11)…,除非有另指—…unless otherwise specified12)…或少于—…or less13)自动化运作—automatic operation14)未注尺寸(详细形状)见三维造型Non dimensioned contour (detailed shape) see 3D model.15)分型线上的飞边(披缝)或段差应小于…Burrs or discrepancy on the P/L shall be … or less.四.标题栏Title Block1.产品名称—part name2.图纸编号 + 版本号(索引号)—drawing no. + level (index)3.一般公差—general tolerance(三)如何阅读制模标准?How to read tooling standard? 一.模具结构术语Mold Construction TermsA.模架Mold Base1.模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸(模厚)—stack height of mould③模具重量—total weight of mould, mould thickness2.定模底板—front plate, top clamping plate, clamp plate, clamping plate 3.定模板—cavity plate, fixed mould plate, A – plate4.动模板—core plate, moving mould plate, B – plate5.浮动板—floating plate6.支撑板—support plate, backing plate7.间隔板,方铁—support blocks, rails, risers, spacer block8.顶杆固定板—retaining plate, ejector retaining plate9.顶板—ejector plate,bottom clamping plate10.动模底板—back plate11.导柱—guide pillar, leader pin, guide pin12.导套—guide bush, leader pin bush13.复位杆—return pin, push-back pin14.弹簧—spring15.撑头—support pillar16.顶针板导柱、导套—ejection guide pin / bush17.垃圾钉—stop pin, stop button18.模脚—standing-off pillars19.标牌—plaque scutcheonB.成型零部件moulding components20.型芯—core insert21.型腔—cavity insert22.镶针—core pin23.镶块—sub-insert, split24.滑块—slide, sliding split25.斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib26.成型顶杆—moulding face pin, form pinC.浇注系统Feed System1.塑料Plastica.主流道—sprueb.分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc.浇口gate常用浇口形式normal gate type :①边缘浇口(J型浇口)—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated.模腔—impressione.冷料井—cold slug wellf.热流道—hot runner2.模具零件mold componentsa.定位圈—locating ring, location ring, register ringb.浇口套—sprue bushc.挡圈—stop ringd.浇口镶块—gate inserte.热流道板—manifoldf.热嘴—hot dropD.分型面及其锁紧、排气Parting Surface, inter-locking & venting1.分型线—parting line ( P/L )2.镶拼线—bodyline, joint line3.平/ 不平的分型面—flat / non – flat parting surface4.封胶面—shut off surfaces, seal-off surfaces5.擦穿位—shut off6.碰穿位—kiss-off7.管位—parting line lock8.分型面的释放(避空) —relief of parting surface9.分型面的平衡—balancing of parting surface10.锁紧角度—locking angle11.锁紧力—clamping force12.锁模块—safety strap13.精定位—Interlock, die lock14.困气—air trap15.排气槽—vent, vent slot16.撬模坑--- pry slot17.计数器--- shot counter/ cycle counterE.滑块机构Slide1.驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2.制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3.导轨—gib, guide strip,center guide4.锁紧块(楔紧块)—heel block, locking heel, wedge block, chase block,slide driver 5.耐磨片—wear plate, wear strip6.压板—retainer,gib7.螺钉—screw8.定位销—dowel pin9.行位扣—slide lock / slide retainer10. flat ejector pin 扁顶针F.斜顶机构Lifter1.斜顶头—lifter head2.斜顶杆—lifter rod, lifter shaft3.斜顶固定块—lifter rod retainer4.斜顶导向块—lifter guide5.开口销—split pin6.固定板(压板)—retainer plate7.耐磨片—wear plate8.铜导套—bronze bushing9.导套固定板—bushing retainer10.衬套—spacer11.导轨—L – gib12.导轨---T-Gib13.滑动块—slide14.连接块—U-CouplingG.顶出系统Ejection System1.基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick on④产品脱模—part is push off from, clear part of mould, separation of part 2.顶板机构Ejector plate assembly①顶板—ejector plate②顶板固定板—retaining plate③推板—stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头—support pillar⑦限位块—stop block,stroke block3.复位机构Return System①复位杆(回程杆)—return pin, push – back pin②垃圾钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of “Belleville” washers⑤早复位机构—early return system⑥强制复位机构—positive return system4.顶出方法Ejection Techniques1)顶杆顶出—pin ejection2)顶管顶出—sleeve ejection3)顶块顶出—bar ejection4)扁顶顶出—blade ejection5)顶板顶出—stripper ejection6)油缸顶出—hydraulic ejection7)气顶—air ejection8)阀门顶出—valve ejection5.顶出元件Ejection Elements1)拉料杆—sprue puller, sucker pin2)顶杆—ejector pin3)阶梯式顶杆—stepped ejector pin4)顶管—ejection sleeve, sleeve5)扁顶—ejector blade, slabbed off ejector pin6)顶块—stripper bar7)顶环—stripper ring8)推板—stripper plate9)加速顶—accelerated ejection10)直顶----straight lifter/EJECTOR BAR6.顶出辅助机构Supplementary operating system1)弹簧柱塞器—spring – loaded plunger2)弹珠定位器—ball catch system3)插销式锁扣—Latch – lock4)尼龙拉杆装置—friction puller device7.电器元件Electric Components1)压力传感器—pressure transducer2)限位开关—limit switchF.冷却系统Cooling System1.基本词汇Basic Word1)温差—temperature variation2)水孔(水道)—waterlines, water-ways, flow-way, channel 3)水路—cooling circuit4)水路示意图—water schematic, schematic circuit5)冷却液—coolant, coolant fluid6)内连接—interconnect7)外连接—external connection8)出口、入口—outlet、inlet9)漏水—water leakage2.水路分布Circuits1)阶梯式水路—stepped system2)分隔板水路—baffled hole system3)斜孔式水路—angled hole system3.水路元件Components1)闷头(螺塞、止水栓)—(threadless)brass pressure plug : female plug & male 2)隔水片—baffle3)密封圈—O – ring4)快插水路接头—quick disconnect fitting, quick connection adaptor5)弯头—elbow6)偶合器(连接器、接头)—adaptor (including a plug & a socket)7)橡皮管—rubber hose8)分水板,集水块—water manifoldG.螺纹、螺纹孔& 螺钉Thread, thread hole & screw1.螺纹—thread2.管螺纹—pipe thread3.螺纹孔—screw hole, tapped hole4.起吊孔—handling hole, jack screw hole, eye bolt hole5.螺钉—screw6.内六角螺钉—socket headed cap screw (s.h.c.s.)7.沉头螺钉—flat headed cap screw (f.h.c.s)8.螺栓—bolt9.螺母—nut10.锁紧螺母—locknut11.螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread (BSP)④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread (UNC)⑥美制细螺纹标准—United Fine thread (UNF)H.润滑Lubrication1.润滑槽—grease groove2.加油管—grease line3.油杯—lubrication fittingI.测量仪器Measuring Instruments1.游标卡尺—vernier caliper2.千分尺—micrometer3.高度规—height gauge4.刻度规—dial gauge5.三坐标测量仪(三次元)—Coordinate Measure Machine(CMM)6.塞规—pin gauge7.圆角量规—radii gauge8.轮廓投影机—profile projectorJ.注塑机参数Injection Machine Parameter1.注塑机规格参数Injection Machine Specification①锁紧类型clamp typea.油缸—hydraulic b.肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2.试模工艺参数Moulding Process Parameter, machine setting①时间Timer(TM), seca.注塑(充填)时间—filling time, injection timeb.冷却时间—cooling timec.补缩时间—packing timed.保压时间—holding timee.成型周期—cycle time②速率、速度Velocity, %、speed, in/seca.注塑(充填)速度—injection speedb.保压速率—hold pressure velocityc.螺杆转速—screw rotation speed③压力Pressure(Prs.), psia.注塑压力—injection pressureb.保压压力—hold pressurec.回压(背压)—back pressure④温度Temperature(Temp.), °Fa.注塑机喷嘴温度—nozzle temp.b.料筒前段、中段、后段温度—barrel front、middle、rear temp.c.模温—mould temp.d.料温—purged resin melt temp.e.空射料温—air shot melt temp.。

模具专业术语英文

模具专业术语英文

模具专业术语英文1. “Core Cavity(型芯型腔),嘿,就像房子的里里外外。

比如说做个塑料小盒子的模具,Core Cavity就决定了盒子的形状,是凹进去还是凸出来的部分,要是搞混了,哎呀,那做出来的盒子可就奇形怪状啦。

”2. “Gating System(浇口系统),这就好比是给模具‘输血’的通道呢。

想象一下你在浇花,那个浇花的水管就像是Gating System。

如果这个通道设计不好,就像水管堵住或者水流太大太小,那模具可就‘营养不良’或者‘撑坏’啦。

”3. “Ejection Mecha nism(顶出机构)。

哟,这可是模具里的‘小助手’呢。

就像从蛋糕模具里把蛋糕取出来得有个东西帮忙顶一下,在模具里,Ejection Mechanism就是干这个的。

要是没有它呀,那些成型的零件就只能卡在里面干着急喽。

”4. “Mold Base(模架),它可是模具的‘骨架’啊。

就像人没了骨架就瘫了一样,模具没了Mold Base那可就散架了。

比如说做个大的汽车零件模具,Mold Base要是不结实,整个模具能行吗?肯定不行呀。

”5. “Runner(流道),这就像小河流一样。

塑料或者金属材料就像河水在这个‘小河’里流动。

要是Runner设计得弯弯曲曲的,就像河流里到处是石头和弯角,那材料流动起来磕磕绊绊的,能做出好的模具产品吗?我看悬。

”6. “Draft Angle(脱模斜度),嘿,这个很重要呢。

这就像是给模具里的零件一个小斜坡,方便它们‘走出来’。

你想想,如果没有这个小斜坡,就像把东西硬塞进一个严丝合缝的盒子里,再想拿出来可就难喽。

”7. “Cooling Channel(冷却通道),它就像模具的‘空调’。

比如说你在夏天干活,没有空调热得受不了。

模具在工作的时候,如果没有Cooling Channel来降温,那热得可就乱套了,可能会影响模具的精度和寿命呢。

”8. “Parting Line(分型线),这就像是模具的‘分界线’。

最全的模具英语专业术语(超级实用)

最全的模具英语专业术语(超级实用)

最全的模具英语专业术语(超级实用)模具专业英语出模: mould unloading, mold stripping 出模角 : Draft Angle 出模方向: The direction of the mold Mold Parting Direction 入水: gate 进入位:gate location水口形式: gate type 大水口: edge gate细水口: pin-point gate 水口大小: gate size转水口:switching runner/gate 唧嘴口径:sprue diameter二、流道: runner热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner流道电脑分析:mold flow analysis 流道平衡: runner balance 热嘴: hot sprue 热流道板: hot manifold发热管: cartridge heater 探针: thermocouples插头: connector plug 插座: connector socket密封/封料: seal三、运水:water line喉塞: line lpug 喉管: tube塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components三板模: 3-plate mold 二板模: 2-plate mold边钉/导边:l eader pin/guide pin 边司/导套: bushing/guide bushing 中托司: shoulder guide bushing 中托边L: guide pin 顶针板: ejector retainner plate 托板: support plate螺丝: screw 管钉: dowel pin开模槽: ply bar scot 内模管位: core/cavity inter-lock顶针: ejector pin 司筒: ejector sleeve司筒针: ejector pin 推板: stripper plate缩呵: movable core,return core core puller扣机(尼龙拉勾): nylon latch lock 斜顶: lifter模胚(架): mold base 上内模: cavity insert下内模: core insert 行位(滑块): slide镶件: insert 压座/斜鸡: wedge耐磨板/油板: wedge wear plate 压条: plate撑头: support pillar 唧嘴: sprue bushing挡板: stop plate 定位圈: locating ring锁扣: latch 扣鸡: parting lock set推杆: push bar 栓打螺丝: S.H.S.B顶板: eracuretun 活动臂: lever arm分流锥: spure sperader 水口司: bush垃圾钉: stop pin 隔片: buffle弹弓柱: spring rod 弹弓: die spring中托司: ejector guide bush 中托边: ejector guide pin镶针: pin 销子: dowel pin波子弹弓: ball catch模具成形不良用语英汉对照aberration 色差 atomization ? 化bank mark ? 料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 colormottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming ? 泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模机械类常用英语:冲压模具-零件类Punch 冲头 insert 入块(嵌入件)deburring punch 压毛边冲子 groove punch 压线冲子stamped punch 字模冲子 round punch 圆冲子special shape punch 异形冲子 bending block 折刀roller 滚轴 baffle plate 挡块located block 定位块 supporting block for location 定位支承块air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆trimming punch 切边冲子 stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子 reel-stretch punch 卷圆压平冲子guide plate 定位板 sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板lower sliding plate 下滑块板 upper holder block 上压块upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板bushing block 衬套 cover plate 盖板guide pad 导料块模具工程常用词汇英汉对照——3high-speed transmission 高速传递 heat dissipation 热传rack 上料 degrease 脱脂rinse 水洗 alkaline etch 龄咬desmut 剥黑膜 D.I. rinse 纯水次Chromate 铬酸处理 Anodize 阳性处理Seal 封孔 Revision 版次part number/P/N 料号 good products 良品scraped products 报放心品 defective products 不良品finished products 成品 disposed products 处理品barcode 条码 flow chart 流程表单assembly 组装 stamping 冲压molding 成型 spare parts=buffer 备品coordinate 座标 dismantle the die 折模auxiliary fuction 辅助功能 poly-line 多义线heater band 加热片 thermocouple 热电偶sand blasting 喷沙 grit 砂砾derusting machine 除锈机 degate 打浇口dryer 烘干机 induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆 edge finder 巡边器concave 凸 convex 凹short 射料不足 nick 缺口speck 瑕?? Shine 亮班splay 银纹 gas mark 焦痕delamination 起鳞 cold slug 冷块blush 导色 gouge 沟槽;凿槽satin texture 段面咬花 witness line 证示线patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机cushion 缓冲 magnalium 镁铝合金magnesium 镁金 metal plate 钣金lathe 车 mill 锉plane 刨 grind 磨drill 铝 boring 镗blinster 气泡 fillet 镶;嵌边through-hole form 通孔形式 voller pin formality 滚针形式cam driver 铡楔 shank 摸柄crank shaft 曲柄轴 augular offset 角度偏差velocity 速度 production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火 carbonization 碳化alloy 合金 tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导 liaison 联络单volatile 挥发性 resistance 电阻ion 离子 titrator 滴定仪beacon 警示灯 coolant 冷却液crusher 破碎机模具工程常用词汇英汉对照——2stock age analysis sheet 库存货龄分析表 on-hand inventory 现有库存available material 良品可使用 obsolete material 良品已呆滞to be inspected or reworked 待验或重工 total 合计cause description 原因说明 part number/ P/N 料号type 形态 item/group/class 类别quality 品质 prepared by 制表notes 说明 physical inventory 盘点数量year-end physical inventory difference analysis sheet 年终盘点差异分析表physical count quantity 帐面数量 difference quantity 差异量cause analysis 原因分析 raw materials 原料materials 物料 finished product 成品semi-finished product 半成品 packing materials包材disposed goods 处理品 warehouse/hub 仓库on way location 在途仓 oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓 skid/pallet 栈板tox machine 自铆机 wire EDM 线割EDM放电机coil stock 卷料 sheet stock 片料tolerance 工差 score=groove 压线cam block 滑块 pilot 导正筒trim 剪外边 pierce 剪内边drag form 压锻差 pocket for the punch head 挂钩槽slug hole 废料孔 feature die 公母模expansion dwg 展开图 radius 半径shim(wedge) 楔子 torch-flame cut 火焰切割set screw 止付螺丝 form block 折刀stop pin 定位销 round pierce punch=die button 圆冲子shape punch=die insert 异形子 stock locater block 定位块under cut=scrap chopper 清角 active plate 活动板baffle plate 挡块 cover plate 盖板male die 公模 female die 母模groove punch 压线冲子 air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板 bushing block 衬套insert 入块 club car 高尔夫球车capability 能力 parameter r参数factor 系数 phosphate 皮膜化成viscosity 涂料粘度 alkalidipping 脱脂main manifold 主集流脉 bezel 斜视规blanking 穿落模 dejecting 顶固模demagnetization 去磁;消磁模具钢材及零件英语模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 硅钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板塑件&模具相关英文compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕 post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式(模具)well type 蓄料井 insulated runner 绝缘浇道方式hot runner 热浇道 runner plat 浇道模块valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头slag well 冷料井 cold slag 冷料渣air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mmwelding line 熔合痕 eject pin 顶出针knock pin 顶出销 return pin 回位销反顶针sleave 套筒 stripper plate 脱料板insert core 放置入子 runner stripper plate 浇道脱料板guide pin 导销 eject rod (bar) (成型机)顶业捧subzero 深冷处理 three plate 三极式模具runner system 浇道系统 stress crack 应力电裂orientation 定向 sprue gate 射料浇口,直浇口nozzle 射嘴 slag well 冷料井side gate 侧浇口 edge gate 侧缘浇口tab gate 搭接浇口 film gate 薄膜浇口flash gate 闸门浇口 slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mmdiaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口pin gate 针点浇口Φ0.8~1.0mm Runner less 无浇道(sprue less) 无射料管方式 long nozzle 延长喷嘴方式Sprue 浇口;溶渣 sprue lock pin 料头钩销(拉料杆)塑件模具相关英文——2eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleave 套筒stripper plate 脱料板 insert core 放置入子runner stripper plate 浇道脱料板 guide pin 导销eject rod (bar) (成型机)顶业捧 subzero 深冷处理three plate 三极式模具 runner system 浇道系统stress crack 应力电裂 orientation 定向sprue gate 射料浇口,直浇口 nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井塑件模具相关英文——1compre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具cavity 型控母模 core 模心公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物 handle mold 手持式模具encapsulation molding 低压封装成型、射出成型用模具hot runner 热浇道 runner plat 浇道模块band heater 环带状的电热器 spindle 阀针spear head 刨尖头 cold slag 冷料渣模具相关英语——7Embosss 凸点 dome 凸圆semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱模具工程类plain die 简易模 pierce die 冲孔模forming die 成型模 progressive die 连续模gang dies 复合模 shearing die 剪边模riveting die 铆合模 pierce 冲孔forming 成型(抽凸,冲凸) draw hole 抽孔bending 折弯 trim 切边101个热处理常用英文词汇1. indication 缺陷2. test specimen 试样3. bar 棒材4. stock 原料5. billet 方钢,钢方坯6. bloom 钢坯,钢锭7. section 型材 8. steel ingot 钢锭9. blank 坯料,半成品 10. cast steel 铸钢11. nodular cast iron 球墨铸铁 12. ductile cast iron 球墨铸铁13. bronze 青铜 14. brass 黄铜15. copper 合金 16. stainless steel 不锈钢17. decarburization 脱碳 18. scale 氧化皮19. anneal 退火 20. process anneal 进行退火21. quenching 淬火 22. normalizing 正火23. Charpy impact text 夏比冲击试验 24. fatigue 疲劳25. tensile testing 拉伸试验 26. solution 固溶处理27. aging 时效处理 28. Vickers hardness 维氏硬度29. Rockwell hardness 洛氏硬度30. Brinell hardness 布氏硬度31. hardness tester 硬度计32. descale 除污,除氧化皮等33. ferrite 铁素体34. austenite 奥氏体35. martensite 马氏体 36. cementite 渗碳体37. iron carbide 渗碳体 38. solid solution 固溶体39. sorbite 索氏体 40. bainite 贝氏体41. pearlite 珠光体 44. grain 晶粒42. nodular fine pearlite/ troostite 屈氏体 45. chromium 铬43. black oxide coating 发黑 46. cadmium 镉47. tungsten 钨 48. molybdenum 钼49. manganese 锰 50. vanadium 钒52. silicon 硅 53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷 55. nitrided 氮化的56. case hardening 表面硬化,表面淬硬 57. air cooling 空冷58. furnace cooling 炉冷 59. oil cooling 油冷60. electrocladding /plating 电镀 61. brittleness 脆性62. strength 强度 63. rigidity 刚性,刚度64. creep 蠕变 65. deflection 挠度66. elongation 延伸率 67. yield strength 屈服强度68. elastoplasticity 弹塑性 69. metallographic structure 金相组织70. metallographic test 金相试验 71. carbon content 含碳量72. induction hardening 感应淬火 73. impedance matching 感应淬火74. hardening and tempering 调质 75. crack 裂纹76. shrinkage 缩孔,疏松 77. forging 锻(件)78. casting 铸(件) 79. rolling 轧(件)80. drawing 拉(件) 81. shot blasting 喷丸(处理)82. grit blasting 喷钢砂(处理) 83. sand blasting 喷砂(处理)84. carburizing 渗碳 85. nitriding 渗氮86. ageing/aging 时效 87. grain size 晶粒度88. pore 气孔 89. sonim 夹砂90. cinder inclusion 夹渣91. lattice 晶格93. spectrum analysis 光谱分析 94. heat/thermal treatment 热处理95. inclusion 夹杂物 96. segregation 偏析97. picking 酸洗,酸浸 98. residual stress 残余应力99. remaining stress 残余应力 101. stress relief 应力释放100. relaxation of residual stress 消除残余应力92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性模具相关英语(5)semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合side stretch 侧冲压平 reel stretch 卷圆压平groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印 tick-mark farside 反面压印冲压名称类extension dwg 展开图 procedure dwg 工程图die structure dwg 模具结构图 material 材质material thickness 料片厚度 factor 系数upward 向上 downward 向下press specification 冲床规格 die height range 适用模高die height 闭模高度 burr 毛边gap 间隙 weight 重量total wt. 总重量 punch wt. 上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧lifter pin 顶料销 eq-height sleeves=spool 等高套筒pin 销 lifter guide pin 浮升导料销guide pin 导正销 wire spring 圆线弹簧outer guiding post 外导柱 stop screw 止付螺丝located pin 定位销 outer bush 外导套模板类top plate 上托板(顶板) top block 上垫脚punch set 上模座 punch pad 上垫板punch holder 上夹板 stripper pad 脱料背板up stripper 上脱料板 male die 公模(凸模)feature die 公母模 female die 母模(凹模)upper plate 上模板 lower plate 下模板die pad 下垫板 die holder 下夹板die set 下模座 bottom block 下垫脚bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板 inner stripper 内脱料板lower stripper 下脱料板注塑模部分中英文对照塑料成形模具 mould for plastics热塑性塑料模 mould for thermoplastics热固性塑料模 mould for thermosets压缩模 compression mould压注模、传递模 transfer mould注射模 injection mould热塑性塑料注射模 injection mould for thermoplastics热固性塑料注射模 injection mould for thermoses序号中文英语日语港台俗称定模座板 fixed clamp plate, top clamping plate. top plate动模座板moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate垫块 spacer parallel支架 ejector housing. mould base leg中文查英文:英语查中文根据国家标准,以下为部分压铸模具术语的标准翻译。

模具英语专业术语

模具英语专业术语

模具英语专业术语模具(MOULD/MOLD,TOOL):CAVITY:前模CORE:后模(定模)DIMENSION:寸法GATE:浇口/水口/入水口PIN GATE:点水口/点浇入水SIDE GATE:边水口/侧浇入水/大水口APPERANCE SURFACE:体裁面WARPAGE DIRECTION:变形方向DRAFT ANGEL:脱模斜度PARTING LINE/P。

L:分模线EJECT PIN/E。

P:注塑顶针BLAST/TEXTURE:喷啥,蚀纹MIRROR FINISH:镜面(抛光)处理POLISH:抛光EMD:放电加工WELD:熔接加工(烧焊)LATHE:车床MILLING CUTTER:铣刀MILLING MACHINE:铣床WIRE CUT:线切割CNC:主加工中心POWER DRILL:电钻DRILLING:钻孔FRITING:烧结ANNEALING:淬火注塑术语(INJECTION)SCREW:螺杆WELD LINE:熔接线SINK MARK:缩水DRAG MARK:脱花BURR:批锋FLOW MARK:流纹SHADOW MARK/GLOSS DIFFERENCE:光影SHORT:缺胶INJECTION CYCLE:成型周期注塑英语型厚大小Thick size锁模结构(机绞/直压)Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式(电动五点,油压五点,油压十三点)Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质(合金)Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量(理论)Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式(全自动/全液压)Drive type (completely automatic/entire hydraulic pressure) 电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程,open ould stroke定产,order production定产效率,efficiency of order prod uction注胶切换点,glue-injection switching point保压压力1,protective pressure倒索,inverse sling模保护,mould protection关模低压,close mould low pressure炮筒温度,gun barrel temperature回料量,returning amount注射压力,injecting pressure色母配比,raw color ratio mixing配套摸具,matched mold顶针次数,thimble times立式注胶机vertical injector工艺卡,WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke 模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finishMatt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersionFR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimensionUnder dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent 阻燃剂Heat stabilizer热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x%减少…含量…%Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模:Injection mould热塑性塑料注射模:Injection mould for thermoplasctics 热固性塑料注射模:Injection mould for thermosets无流道模:Runerless mould热流道模:Hot runner mould绝热流道模:Insulated温流道模:Warm runner mould2. 浇注,排溢,分型浇注系统:Feed system主流道:Sprue分流道:Runner浇口:Gate直接浇口:Direct gate ;Sprue gate环行浇口:Ring gate盘型浇口:Disk gate ;Diaphragm轮辐浇口:Spoke gate :Spider gate点浇口:Pin-point gate侧浇口:Edge gate潜伏浇口:Submarine gate护耳浇口:Tab gate扇型浇口:Fan gate 牛角浇口:Horn gate冷料穴:Cold-slug well浇口套:Sprue bush ;Sprue bushing浇口镶块:Gating insret分流锥:Sprader流道板:Runner plate热流道板:Manifold block;Hot-runner manifold 温流道板:Warm runner plate二级喷嘴:Secondary nozzle鱼雷形组合体:T orpedo;Torpedo body assembly 管式加热器:Cartridge heater热管:Heat pipe阀式浇口:Valve gate加热腔:Loading chamber柱塞:Force plunger;Pot plungr溢料槽:Flash grorve ;Spew grovve排气槽:Vent分型面:Parting line水平分型面:Horizontal parting half垂直分型面:Vertical parting half3. 成型零件定模:Stationary mould:Fixed half动模;Movable mould ;Moving half上模:Upper mould;Upper half下模:Lower mould :Lower half型腔:Cavity凹模:Impression;Cavity plate镶件:Mould insert活动镶件:Movable insert;Lose detail拼块:Splits凹模拼块:Cavity splits型芯拼块:Core splits型芯:Core侧型芯:Side core:slide core螺纹型芯:Thread plug;Threaded core螺纹型环:Thread ring;Threaded cavity凸模:Punch;Force嵌件:Insert for mould4. 支持与固定零件定模座板:Fixed clamp plate:Top clamping plate;T op plate动模座板:Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板:Upper clamping plate下模座板:Lower clamping plate凹模固定板:Cavity-retaier plate型芯固定板:Core-retaier plate凸模固定板:Punch-retaier pilte模套:Chase ;Bolster;Frame;支撑板:Backing plate垫块:Spacer parallel支架:Ejector housing支撑柱:Support pillar模板:Mould plate5. 抽芯零件斜销:Angle pin; Finger cam滑块:Slide;Cam slide侧型芯滑块:Slide core-slide滑块导板:Slide guide strip锲紧块:Heel block;Wedge block;Locking heel斜槽导板:Finger guide plate弯销:Dog-leg cam斜滑块:Angled-lift splits6. 导向零件导柱:Guide pillar;Guide pin;Leader pin带头导柱:Guide pillar ;Straight leader pin带肩导柱:Guide pillar Shouldered;Shoulder leader pin 推板导柱:Ejector guide pillar;Ejeector guide pin导套:Guide bush ;Guide bushing直导套:Guide bush ;Straight ;Straight bushing带头导套:Guide bush ;Shoulder bushing推板导套:Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈:Locating ring锥形定位圈:Mould bases locating elements复位杆:Ejector plate return pin;Push-back pin限位钉:Stop pin;Stop button限位块:Stop block ;Stop pad定距拉杆:Length bolt;Puller bolt定距拉板:Puller plate;Limit plate8. 推出零件推杆:Ejector pin圆柱头推杆:Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管:Ejector sleeve推块:Ejector pad推件板:Stripper plate推件环:Stripper ring;Stripper dlisk推杆固定板:Ejector retainer plate推板:Ejector plate;Ejection plate连接推杆:Ejector tie rod 拉料杆:Sprue puller钩形垃料杆:Sprue puller ;Z-shaped球头垃料杆:Sprue puller;Ball headed圆锥头垃料杆:Sprue puller;Conical headed分流道垃料杆:Runner puller;Runner lock pin推流道板:Runner stripper plate9. 冷却和加热零件冷却通道:Cooling channel;Cooling line隔板:Baffle加热板:Heating plate隔热板:Thermal insulation board10. 模架模架:Mould base标准模架:Standard mould base11. 塑料成型模具的主要设计要素注射能力:Shot capacity收缩率:Shrinkage注射压力:Injection pressure锁模力:Clamping force ;Locking force成型压力:Moulding pressure模内压力:Internal mould pressure;Cavity pressure 开模力:Mould opening force脱模力:Ejection force抽芯力:Core-pulling force抽芯距:Core-pulling distance闭合高度:Mould shut height最大开距:Maximum daylight;Open daylight 投影面积:Projected area脱模斜度:Draft脱模距:Stripper distance。

模具英语专业术语

模具英语专业术语

模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水:gate进入位(入水点):gate location水口形式:gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口:pin-point gate水口大小:gate size转水口:switching runner/gate唧嘴口径:sprue diameter直接水口: direct gate二、流道: runner热流道:hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道:round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析):mold flow analysis 流道平衡: runner balance热嘴:hot sprue/tip热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头:connector plug插座:connector socket密封/封料:seal三、运水:water line喉塞:line plug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socket 四、模具零件:mold components 三板模(细水口模):3-plate mold二板模(大水口模):2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边:leader pin/guide pin边司/导套:guide pin/guide bushing直导套:shoulder guide bushing有托导套:straight guide bushing中托司:ejector guide bush中托边:ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板:stripper plateB板: B plate托板:support plate方铁: spacer block加高方铁: higher spacer block顶针固定板:ejector retainner plate顶针板:ejector plate底板: bottom clamp plate螺丝:screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt管钉:dowel pin开模槽:ply bar socket内模管位(模仁互锁):core/cavity inter-lock顶针:ejector pin司筒:ejector sleeve司筒针:sleeve ejector pin缩呵:movable core,return core, core puller 扣机(尼龙拉勾):nylon latch lock斜顶:lifter模胚(架):mold base上内模:cavity insert下内模:core insert行位(滑块):slide行位扣:镶件:insert压座/斜鸡:wedge耐磨板/油板:wear plate压条:gib撑头: support pillar唧嘴:sprue bushing挡板:stop plate定位圈(法兰):locating ring锁扣(模锁):latch扣鸡:parting lock set推杆:push bar顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针:insert pin销子(销钉):dowel pin波子弹弓:ball catch喉塞(堵头): pipe plug锁模块:lock plate斜顶杆:angle ejector rod斜顶针:angle from pin尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边(斜导柱):angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语:terms承压平面平衡:parting surface support balance分模面排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes with ejector pin料位出上/下模:part from cavity (core) side模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件:Do not use (core/cavity) insert用铍铜做镶件:use beryllium copper insert初步模图设计:preliminary mold design正式模图设计:final mold design反呵:reverse core弹弓压缩量:spring compressed length稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模(粘模):sticking顶白: stress mark热膨胀:thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差:tolorance铜公(电极):copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。

模具英语专业术语大全

模具英语专业术语大全

模具英语专业术语大全1. Introduction模具制造是制造业中的关键领域之一。

在模具制造过程中,使用了许多专业术语来描述不同的工艺和技术。

了解这些专业术语对于模具制造工程师和相关行业人员非常重要。

本文将介绍一些常用的模具英语专业术语,帮助读者更好地理解和应用这些术语。

2. Injection Molding Terminology(注塑成型术语)2.1 Injection Molding(注塑成型)Injection molding is a manufacturing process used to produce parts by injecting molten material into a mold cavity. This process is widely used in the production of plastic parts.A mold is a tool used in the injection molding process to shape the molten material into a desired form. It consists of a mold cavity and a mold core.2.3 Cavity(腔)The cavity is the part of the mold that forms the exterior of the molded part. It is the space where the molten material fills and solidifies.2.4 Core(芯)The core is the inner part of the mold that shapes the interior of the molded part. It is used in combination with the cavity to create the desired shape.2.5 Runner(导道)The runner is a channel that connects the injection machine to the mold cavity. It allows the molten material to flow into the mold cavity.The gate is the opening through which the molten material enters the mold cavity from the runner. There are different types of gates, such as edge gate, pin gate, and submarine gate.2.7 Cooling System(冷却系统)The cooling system is used to cool down the molten material inside the mold cavity and solidify it. It consists of cooling channels that circulate cooling water.2.8 Ejector System(射出系统)The ejector system is used to eject the molded part from the mold cavity after it has solidified. It consists of ejector pins or ejector plates.2.9 Mold Clamping(模具夹紧)Mold clamping is the process of securely holding the mold halves together during injection molding. It ensures that the mold cavity and the core mntn their proper alignment.2.10 Venting(排气)Venting is the process of allowing r to escape from the mold cavity during injection molding. It prevents r pockets and gas bubbles from forming inside the molded part.3. Die-Casting Terminology(压铸术语)3.1 Die-Casting(压铸)Die-casting is a manufacturing process used to produce metal parts by forcing molten metal into a mold cavity under high pressure. It is commonly used for the production of automotive and aerospace components.3.2 Die(压铸模具)A die is a tool used in the die-casting process to shape the molten metal into a desired form. It consists of two halves, the fixed half and the ejector half.3.3 Shot Sleeve(浇注套筒)The shot sleeve is a component of the die-casting machine that holds the molten metal before it is injected into the die cavity. It acts as a reservoir and provides a controlled flow of metal.3.4 Shot Chamber(浇注腔室)The shot chamber is the space in the die cavity where the molten metal is injected. It is formed by the fixed half of the die and the ejector half.3.5 Sprue(浇口)The sprue is the channel through which the molten metal flows from the shot sleeve to the shot chamber. It allows the metal to enter the die cavity.3.6 Runner System(导道系统)The runner system is a network of channels that distribute the molten metal from the sprue to multiple cavities in the die. It ensures even distribution of metal and helps mntn the desired temperature.3.7 Venting System(排气系统)The venting system is used to remove r and gases from the die cavity during the die-casting process. It prevents the formation of porosity and gas-related defects in the castings.3.8 Die Lubricant(模具润滑剂)Die lubricant is a substance applied to the die cavity surface to reduce friction between the molten metal and the die. It helps to prolong the life of the die and improve the quality of the castings.3.9 Casting Release Agent(浇注剂)A casting release agent is applied to the die cavity surface to facilitate the release of the solidified casting from the die. It helps prevent sticking and damage to the casting.3.10 Die-Casting Machine(压铸机)A die-casting machine is a specialized machine used to perform the die-casting process. It consists of a die-casting unit, a shot system, and a control system.4. Conclusion本文介绍了一些常用的模具英语专业术语,涵盖了注塑成型和压铸两个重要领域。

模具专业英文术语大全

模具专业英文术语大全

模具英语专业术语模具述语一、入水:gate进入位: gate location水口形式:gate type大水口:edge gate细水口: pin-point gate水口大小:gate size转水口: switching runner/gate唧嘴口径: sprue diameter二、流道: runner热流道: hot runner,hot manifold热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道:round(full/half runner流道电脑分析:mold flow analysis流道平衡:runner balance热嘴: hot sprue热流道板:hot manifold发热管:cartridge heater探针: thermocouples插头: connector plug插座: connector socket密封/封料: seal三、运水:water line喉塞:line lpug喉管:tube塑胶管:plastic tube快速接头:jiffy quick connector plug/socker四、模具零件: mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板: support plate螺丝: screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针: ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock 斜顶:lifter模胚(架): mold base上内模:cavity insert下内模:core insert 行位(滑块): slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴: sprue bushing挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut onA-plate,core direct cuton B-plate.不准用镶件: Do not use (core/cavity) insert用铍铜做镶件: use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length 稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrodeMold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Pressing dies 压模Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具塑料模具 mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板A plateB 板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line (flow line)三板式模具 three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machinecompre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具(移转成型用模具)encapsulation molding 低压封装成型(射出成型用模具)two plate 两极式(模具)well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)(成型机)顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口,直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号) shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板(顶板)top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块塑料模具专业术语动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate下模座板 lower clamping plate凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate凸模固定板 punch-retainer plate模套 chase. bolster. frame支承板 backing plate. supprr plate 垫块 spacer parallel支架 ejector housing. mould base leg压力铸造模具 die-casting die压铸模零部件定模 fixed die, cover die定模座板 fixed clamping plate 定模套板 bolstor, fixed die动模 moving die,ejector die动模座板 moving clamping plate 直流道 sprue横流道 runner内浇口 gatelanded plunger mold||有肩柱塞式模具burnishing die||挤光模landed positive mold||有肩全压式模具button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具loose detail mold||活零件模具chill mold||冷硬用铸模loose mold||活动式模具clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模offswt bending die||双折冷弯模具extrusion die||挤出模palletizing die||叠层模family mold||反套制品模具plaster mold||石膏模blank through dies||漏件式落料模porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模fishtail die||鱼尾形模具profile die||轮廓模flash mold||溢料式模具progressive die||顺序模gypsum mold||石膏铸模protable mold||手提式模具hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模punching die||落料模lancing die||切口模raising(embossing)||压花起伏成形re-entrant mold||倒角式模具sectional die||拼合模runless injection mold||无流道冷料模具sectional die||对合模具segment mold||组合模semi-positive mold||半全压式模具shaper||定型模套single cavity mold||单腔模具solid forging die||整体锻模split forging die||拼合锻模split mold||双并式模具sprueless mold||无注道残料模具squeezing die||挤压模stretch form die||拉伸成形模sweeping mold||平刮铸模swing die||振动模具three plates mold||三片式模具trimming die||切边模unit mold||单元式模具universal mold||通用模具unscrewing mold||退扣式模具yoke type die||轭型模模具钢材khuôn thépalloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板塑件与模具compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具(移转成型用模具)encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具)well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)(成型机)顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压 rated voltage额定电流 rated current接触电阻contact resistance绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage针pin 物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity 接触长度contact length接触件电镀层contact plating 接触压力contact pressure接触件中心距contact space 接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ,Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printedcircuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board,Double-sided board表面安装surface Mounting翘曲warp, bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面)parting line定模stationary mould,Fixed mould动模movable mould, movable half上模upper mould, upper half下模lower mould, lower half型腔cavity凹模cavity plate,cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line (flow line)三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time 闭模时间closing time定型装置sizing system阴模female mould,cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine模具零件Top Plate 上托板(顶板)Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模(凸模)Feature Die 公母模Female Die 母模(凹模)Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板(底板)Stripping Plate 内外打(脱料板)Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块(嵌入件)Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising(Embossing)压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide(Slide Core)滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具术语翻译动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top ClampingPlate Top Plate动模座板 Moving Clamp Plate Bottom ClampingPlate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准,以下为部分压铸模具标准翻译。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

模具工程常用词汇模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel钼系高速钢molybdenum steel钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板四、模具零件:mold components三板模:3-plate mold二板模:2-plate mold边钉/导边:leader pin/guide pin边司/导套:bushing/guide bushing中托司:shoulder guide bushing中托边L:guide pin顶针板:ejector retainner plate托板:support plate螺丝:screw管钉:dowel pin开模槽:ply bar scot内模管位:core/cavity inter-lock顶针:ejector pin司筒:ejector sleeve司筒针:ejector pin推板:stripper plate缩呵:movable core,return core core puller扣机(尼龙拉勾):nylon latch lock斜顶:lifter模胚(架):mold base上内模:cavity insert下内模:core insert行位(滑块):slide镶件:insert压座/斜鸡:wedge耐磨板/油板:wedge wear plate压条:plate撑头: support pillar唧嘴:sprue bushing 挡板:stop plate定位圈:locating ring锁扣:latch扣鸡:parting lock set推杆:push bar栓打螺丝:S.H.S.B顶板:eracuretun活动臂:lever arm分流锥:spure sperader水口司:bush垃圾钉:stop pin隔片:buffle弹弓柱:spring rod弹弓:die spring中托司:ejector guide bush中托边:ejector guide pin镶针:pin销子:dowel pin波子弹弓:ball catch喉塞: pipe plug锁模块:lock plate斜顶:angle from pin斜顶杆:angle ejector rod尼龙拉勾:parting locks活动臂:lever arm复位键、提前回杆:early return bar气阀:valves斜导边:angle pin术语:terms承压平面平衡:parting surface support balance模排气:parting line venting回针碰料位:return pin and cavity interference模总高超出啤机规格:mold base shut hight顶针碰运水:water line interferes withejector pin料位出上/下模:part from cavith (core) side模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件:Do not use (core/cavity) insert用铍铜做镶件:use beryllium copper insert初步(正式)模图设计:preliinary (final) mold design反呵:reverse core弹弓压缩量:spring compressed length稳定性好:good stability,stable强度不够:insufficient rigidity均匀冷却:even cooling扣模:sticking热膨胀:thero expansion公差:tolorance铜公(电极):copper electrode模具工程常用词汇die 模具die shoe 模座figure file, chart file图档cutting die, blanking die冲模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔 panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化 die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board范本padding block垫块stepping bar垫条upper die base上模lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧 bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验PCE assembly production schedule sheet PCE组装厂生产排配表model机钟work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割 EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数 factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision 版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条形码 flow chart流程窗体 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate坐标 dismantle the die折模 auxiliary fuction 辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疵 shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank 摸柄 crank shaft曲柄 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键quenching淬火 tempering 回火annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性resistance 电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die 冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce 冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 punch wt.上模重量五金零件类inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销coil spring弹簧 lifter pin顶料销 eq-heightsleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销wire spring圆线弹簧 outer guiding post 外导柱 stop screw止付螺丝 located pin定位销 outer bush 外导套范本类top plate上托板(顶板) top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板stripper pad脱料背板up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板)outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch一、 = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块 sliding dowel block滑块固定块 active plate活动板 lower sliding plate下滑块板 upper holder block上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型 flash mold溢流式模具 plsitive mold挤压式模具split mold分割式模具 cavity型控母模 core模心公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding mark溶合痕 post screw insert螺纹套筒埋值self tapping screw自攻螺丝 striper plate脱料板piston活塞 cylinder汽缸套 chip细碎物 handle mold掌上型模具(移转成型用模具) encapsulation molding低压封装成型(射出成型用模具)two plate两极式(模具) well type蓄料井 insulated runner 绝缘浇道方式 hot runner热浇道 runner plat浇道模块 valve gate阀门浇口 band heater环带状的电热器 spindle阀针 spear head刨尖头 slag well冷料井 cold slag冷料渣 air vent排气道 welding line熔合痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子runner stripper plate浇道脱料板 guide pin导销 eject rod (bar)(成型机)顶业捧 subzero深冷处理three plate三极式模具runner system浇道系统 stress crack应力电裂 orientation 定向 sprue gate射料浇口,直浇口 nozzle射嘴 sprue lock pin料头钩销(拉料杆) slag well冷料井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇口 film gate薄膜浇口 flash gate闸门浇口slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 diaphragm gate隔膜浇口 ring gate环形浇口 subarine gate潜入式浇口tunnel gate隧道式浇口 pin gate针点浇口 Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣各种模具常用成形方式 accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法 laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模transfer die连续自动冲切,连续冲模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下范本bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底 die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲范本die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆 ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形范本finish machined round plate 圆形范本fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧范本one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下范本shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝范本模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢 nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板tap 攻牙表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动范本foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑料片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑料原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑料polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PPpolystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑料unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕range peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 范本印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening橘皮状表皮皱折surging 波动torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具工作法用语adjustable spanner 活动扳手angle cutter 角铣刀arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 迭板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 折迭加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重迭加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage Idle Station 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部loader 供料器 unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床。

相关文档
最新文档