中英文故障对照表

故障代码中文解释Err000无错误
(* No error *)
Err001变频器检测电网掉电(* Grid Loss detected by power converter Err002保留(* Reserve *) (* 0*)Err003保留
(* Reserve *) (* 0*)
Err004变频器复位超时(* Timeout occurred converter reset *) (Err005PLC软件ID不正确(* Plc software identification number no Err006变桨软件版本不正确(* Pitch software versions not correct *Err007偏航软件版本不正确
(* Yaw software version not correct *) (Err008初始化时,轮毂未达到停止状态(* In initialization, hub doesn't reach Err009变频器软件版本不正确(* Converter software version not correc Err010检测不到机舱零位置(* Zero position nacelle can't be found Err011SS-0 熔丝熔断 (* SS-0: Fuse melted *) (* 3*)
Err012SS-1 急停按钮 (* SS-1: Emergency button *) (* 3*)Err013SS-5 发电机超速 (* SS-5: Generator over speed *) (* 2*)Err014SS-6 振动传感器 (* SS-6: Vibration sensor *) (* 2*)Err015SS-7 转子超速 (* SS-7: Rotor over speed *) (* 5*)Err016SS-8 看门狗 (* SS-8: Watchdog *) (* 2*)
Err017SS-9 制动器位置 (* SS-9: Brake position *) (* 2*)
Err018SS-10 超出工作位置 (* SS-10: Working position exceeded *) (Err019SS-11 轮糓驱动
(* SS-11: Hub drives *) (* 2*)
Err020SS-12 存储继电器未复位(* SS-12: Storage relay not reset *) (* Err021柜内24V熔丝(* Fuse 24V internal cabinet *) (* 0*)Err022柜外24V熔丝
(* Fuse 24V external cabinet *) (* 0*)Err023功率变频器未连接CAN总线(* Power converter not at the CANbus *) Err024功率变频器检查到故障(* Error detected by power converter *) Err025实际功率与要求功率不同(* Actual power differes to demanded *) Err026风速风向仪24V熔丝
(* Fuse 24V anemometer *) (* 0*)
Err027数字模块10未与CAN总线连接(* Digital module 10 not at bus *) (* 2*Err028模拟模块未与总线连接(* Analogue module not at bus *) (* 0*)Err029690V电流接触器侧熔丝(* Fuse line side contactor 690V *) (* 0Err03024V辅助电源熔丝(* Fuse 24V auxiliaries *) (* 0*)Err031变桨1通讯(* Communication pitch1 *) (* 2*)Err032变桨2通讯(* Communication pitch2 *) (* 2*)Err033变桨3通讯
(* Communication pitch3 *) (* 2*)
Err034SS-2制动器转子过速(* SS-2: over speed rotor for brake *) (Err035SS-3 三个叶片故障(* SS-3: All three blades error *) (* 5*Err036SS-4 制动器存储继电器(* SS-4: Brake storage relays *) (* 5*)Err037保留
(* Reserve *) (* 0*)
Err038变桨1停止超时(* Pitch 1 timeout Stop *) (* 0*)
Err039变桨1基准位置超时(* Pitch 1 timeout Reference *) (* 0*)Err040变桨1合理性(* Pitch 1 plausibility *) (* 2*)Err041变桨2停止超时(* Pitch 2 timeout Stop *) (* 0*)
Err042变桨2基准位置超时(* Pitch 2 timeout Reference *) (* 0*)Err043变桨2合理性(* Pitch 2 plausibility *) (* 2*)Err044
变桨3停止超时
(* Pitch 3 timeout Stop *) (* 0*)
中英文故障对照表
英文
Err045变桨3基准位置超时(* Pitch 3 timeout Reference *) (* 0*) Err046变桨3合理性(* Pitch 3 plausibility *) (* 2*)
Err047保留(* Reserve *) (* 0*)
Err048变桨1手动操作盒连接(* Pitch 1 service box connected *) (* 2 Err049变桨1驱动错误(* Pitch 1 drive error *) (* 2*)
Err050保留(* Reserve *) (* 0*)
Err051变桨2手动操作盒连接(* Pitch 2 service box connected *) (* 2 Err052变桨2驱动错误(* Pitch 2 drive error *) (* 2*)
Err053保留(* Reserve *) (* 0*)
Err054变桨3手动操作盒连接(* Pitch 3 service box connected *) (* 2 Err055变桨3驱动错误(* Pitch 3 drive error *) (* 2*)
Err056变桨1位置延时故障(* Pitch1 position error delayed *) (* 0 Err057变桨2位置延时故障(* Pitch2 position error delayed *) (* 0 Err058变桨3位置延时故障(* Pitch3 position error delayed *) (* 0 Err059变桨位置没有同步变慢(* Pitch positions not synchronous slow Err060变桨位置没有同步变快(* Pitch positions not synchronous fast Err061轮毂速度未设置为最大速度(* Maximum hub speed not set to the rate Err062变桨1基准位置错误(* Pitch1 reference positioning error *) Err063变桨2基准位置错误(* Pitch2 reference positioning error *) Err064变桨3基准位置错误(* Pitch3 reference positioning error *) Err065变桨1限位开关未在初始状态(* Pitch 1 limiting switch not active in Err066变桨2限位开关未在初始状态(* Pitch 2 limiting switch not active in Err067变桨3限位开关未在初始状态(* Pitch 3 limiting switch not active in Err068变桨1限位开关未在安全状态(* Pitch 1 limiting switch not active in Err069变桨2限位开关未在安全状态(* Pitch 2 limiting switch not active in Err070变桨3限位开关未在安全状态(* Pitch 3 limiting switch not active in Err071快速停止超时-高速(* Fast stop timeout high speed *) (* 2* Err072快速停止超时-低速(* Fast stop timeout low speed *) (* 2*) Err073完全停止超时-高速(* Full stop timeout high speed *) (* 2* Err074完全停止超时-高速(* Full stop timeout low speed *) (* 2*) Err075安全链停止超时-高速(* Safety chain stop timeout high speed Err076安全链停止超时-低速(* Safety chain stop timeout low speed * Err077网侧变频器电流测量(* LSC current measurement *) (* 0*)
Err078发电机侧变频器电流测量(* GSC current measurement *) (* 0*)
Err079直流母线连接网电压预充电(* DC bus to Line voltage in precharge * Err080发电机编码器反馈(* Generator encoder feedback *) (* 0*) Err081滑环编码器反馈(* Hub slipring encoder feedback *) (* 0 Err082轮毂速度波动误差限度(* Hub speed fluctuation error limit *) Err083保留(* Reserve *) (* 0*)
Err084保留(* Reserve *) (* 0*)
Err085保留(* Reserve *) (* 0*)
Err086保留(* Reserve *) (* 0*)
Err087保留(* Reserve *) (* 0*)
Err088保留(* Reserve *) (* 0*)
Err089保留(* Reserve *) (* 0*)
Err090保留(* Reserve *) (* 0*)
Err091保留(* Reserve *) (* 0*)
Err092无油泵时齿轮箱压力(* Gearbox pressure at no pumping *) (* Err093齿轮箱加热超时(* Timeout gearbox heating *) (* 0*)
Err094电池充电超时(* Timeout battery charging *) (* 0*) Err095偏航超时(* Timeout yawing *) (* 0*)
Err096转速与转子速度信号有差异(* Speed difference rotor speed signals Err097速度继电器1电缆切断(* Wire cut rotor speed relais 1 *) (* 2 Err098速度继电器2电缆切断(* Wire cut rotor speed relais 2 *) (* 2 Err099保留(* Reserve *) (* 0*)
Err100保留(* Reserve *) (* 0*)
Err101保留(* Reserve *) (* 0*)
Err102保留(* Reserve *) (* 0*)
Err103NCC310柜急停按钮(* NCC310 cabinet emergency stop button Err104TBC300齿轮箱急停按钮(* CTB300 Gearbox emergency stop button Err105TBC100急停按钮(* TBC100 emergency stop button *) (* 3* Err106机舱电池柜电压过高或者无连接(* Nacelle battery extremly high or not Err107高压变压器温度(* HV Transformer temperature *) (* 0*) Err108发电机传感器PT100悬空(* PT100 sensor generator overhang *) (* Err109发电机传感器PT100悬空(* PT100 sensor generator overhang *) (* Err110发电机传感器PT100悬空(* PT100 sensor generator overhang *) (* Err111发电机轴驱动侧传感器PT100(* PT100 sensor generator bearing drive Err112发电机轴非驱动侧传感器PT100(* PT100 sensor generator bearing non dr Err113齿轮箱轴传感器PT100(* PT100 sensor gearbox bearing *) (* 0* Err114齿轮箱油温传感器PT100(* PT100 sensor gearbox oil *) (* 0*) Err115机舱电池柜电压过低或者无连接(* Nacelle battery extremly low or not c Err116机舱温度高(* Nacelle temperature high *) (* 0*) Err117机舱温度传感器缺失(* Nacelle temperature sensor defect *) Err118转子扼流圈温度高(* Rotor choke temperature high *) (* 0* Err119网侧变频器滤波熔丝(* Fuse for filter at line side converte Err120未达到偏航额定转速(* Yaw rated speed not reached *) (* 0*) Err121环境温度太高(* Environment temperature too high *) ( Err122发电机内温度(* Temperature generator overhang *) (* Err123发电机轴温(* Temperature generator bearing *) (* 0 Err124齿轮箱油温(* Temperature gearbox oil *) (* 0*)
Err125机舱柜温度(* Temperature nacelle cabinet *) (* 0*) Err126齿轮箱轴温(* Temperature gearbox bearing *) (* 0*) Err127刹车垫磨损大于2mm(* Brake pad wear > 2 mm *) (* 0*)
Err128制动泵无压力(* Brake pump no pressure *) (* 0*)
Err129安全链没有检测到制动器关闭(* Closed brake not detected by safety c Err130齿轮箱油位太低(* Gearbox oil level too low *) (* 0*) Err131齿轮箱油温高于90°(* Gearbox oil temperature > 90鳦 *) (* Err132制动泵断路器(* Circuit breaker brake pump *) (* 0*) Err133接地故障保护限制低(* Ground fault protection limit low *) Err134接地故障保护限制低(* Ground fault protection limit high *) Err135电池检测失败三次,低电压(* Battery test failed three times, low Err136保留(* Reserve *) (* 0*)
Err137接地故障保护信号切断(* Ground fault protection signal cut *) Err138竖立时,机舱位置变化(* Nacelle position change during stand
Err139自动制动调节(* Automatic brake adjust *) (* 0*)
Err140机舱位置超出(* Nacelle position exceeded *) (* 0*) Err141偏航变频器熔丝(* Fuse yaw converter *) (* 0*)
Err142熔丝或直流电源接地(* Fuse or earth current DC supply *) (* Err143制动器位置不够(* Brake open position not reached *) (* Err144齿轮箱断路器-高速(* Circuit breaker gearbox high speed *) Err145转子开关未设定在自动模式(* Rotor lock switch not set in automati Err146制动阀缺失(* Brake valve defect *) (* 2*)
Err147400V中断(* 400V interuption *) (* 0*)
Err148电池接地故障(* Battery earth fault *) (* 0*)
Err149齿轮箱泵低速运行断路器(* Circuit breaker gearbox low speed *) Err150轮毂速度过低(* Speed difference small rotor speed *) Err151发电机转速过低(* Speed difference generator speed too Err152超速级别高(* Over speed level high *) (* 4*)
Err153超速级别低(* Over speed level low *) (* 4*)
Err154齿轮箱高速泵无压力(* Gearbox high speed pump no pressure * Err155电池检测电网掉电(* Grid loss detected by battery *) (* 0 Err156机舱位置变化太小(* Position change in nacelle position i Err157电池检测时电压变化小(* Too small voltage difference battery Err158检测到发电机过速(* over speed by generator signal *) (* Err159变频器不同步(* Converter did not synchronise *) (* 0 Err160风速风向仪测量错误(* Anemometer measurement error. *) (* 0 Err161保留(* Reserve *) (* 0*)
Err162风速在0m/s超过9小时(* winspeed signal zero for 9h *) (* 0*) Err163风速计通讯错误(* Anemometer communication error *) (* Err164PT100传感器电池温度(* PT100 sensor battery temperature *) ( Err165电池温度过低(* Battery too low temperature *) (* 0*) Err166保留(* Reserve *) (* 0*)
Err167在备用或更新单元电池电压过低(* Battery voltage too lowstandby or ref Err168与偏航变频器连接的手动操作箱(* Service box yaw converter connected * Err169功率消耗 > 30 KW(* Power consumption > 30 kW *) (* 0*) Err170偏航变频器没有连接到CAN总线上(* Yaw converter not on CAN-BUS *) (* 0* Err171偏航时机舱位置无变化(* No change in the nacelle positionmovi Err172230V偏航制动器熔丝(* Fuse yaw brake 230V *) (* 0*)
Err173水泵的断路器(* Circuit breaker water pump *) (* 0*) Err174变频柜入水口水压阀断路器(* Circuit breaker water valve at conver Err175变浆制动器熔丝230V(* Fuse pitch brake 230V *) (* 0*)
Err176保留(* Reserve *) (* 0*)
Err177保留(* Reserve *) (* 0*)
Err178变频器CAN数据复用器不工作(* Converter CAN data multiplexer not OK Err179碳刷监控故障(* Reserve *) (* 0*)
Err180保留(* Reserve *) (* 0*)
Err181保留(* Reserve *) (* 0*)
Err182保留(* Reserve *) (* 0*)
Err183保留(* Reserve *) (* 0*)
Err184保留(* Reserve *) (* 0*)
Err185保留(* Reserve *) (* 0*)
Err186保留(* Reserve *) (* 0*)
Err187保留(* Reserve *) (* 0*)
Err188保留(* Reserve *) (* 0*)
Err189保留(* Reserve *) (* 0*)
Err190保留(* Reserve *) (* 0*)
Err191保留(* Reserve *) (* 0*)
Err192保留(* Reserve *) (* 0*)
Err193保留(* Reserve *) (* 0*)
Err194保留(* Reserve *) (* 0*)
Err195保留(* Reserve *) (* 0*)
Err196保留(* Reserve *) (* 0*)
Err197保留(* Reserve *) (* 0*)
Err198保留(* Reserve *) (* 0*)
Err199保留(* Reserve *) (* 0*)
Err200保留(* Reserve *) (* 0*)
Err201保留(* Reserve *) (* 0*)
Err202保留(* Reserve *) (* 0*)
Err203保留(* Reserve *) (* 0*)
Err204保留(* Reserve *) (* 0*)
Err205变频器CROWBAR安全检查(* Health check converter crowbar *) (* Err206DC bus电压，变浆，电池电压的自检(* Health check difference DC bus voltag Err207自检变浆到设定位置的工作时间(* Health check timeout pitch move to de Err208在安全链打开的情况下，桨叶不向回移动(* Health check pitch not move back at o Err209安全检查时制动器没有关闭(* Health check brake not closed *) (* 0 Err210安全检查时制动器压力(* Health check brake pressure *) (* 0*) Err211安全检查时风速风向仪不正确(* Health check anemometer not plausible Err212安全检查时电池无法使变浆回位(* Health check pitch not moved back by Err213安全检查时电池没有检测到电网掉电(* Health check batteries didn't detect Err214安全检查轴承摩擦太大(* Health check friction bearing too hig Err215不间断电源完全放电, 电流接触器(* Battery UPS total discharging, contac Err216不间断电源测试启动, 电流接触器(* Battery UPS test activation, contacto Err217400V不间断电源 电流接触器1(* Battery UPS 400V contactor1 *) (* 0*) Err218400V不间断电源 电流接触器2(* Battery UPS 400V contactor2 *) (* 0*) Err219直流电源500V电流接触器没关闭(* Contactor supply 500V DC not closed * Err220柜风扇熔断器(* Fuse cabinet fans *) (* 0*)
Err221230V 电源接口继电器熔丝(* Fuse interface relays 230V supply *) Err222滤波板温度(* Filter plate temperature *) (* 0*) Err223自动加热器熔丝(* Fuse thermostat heating *) (* 0*)
Err224偏航变频器温度(* Yaw converter error *) (* 0*)
Err225制动泵接触器(* Brake pump contactor *) (* 0*)
Err226塔筒通信失败看门狗显示(* Tower base communication failure watc Err227保留(* Reserve *) (* 0*)
Err228保留(* Reserve *) (* 0*)
Err229变频器阻流其温度(* Converter choke temperature *) (* 0*) Err230齿轮箱风扇接触器(* Gearbox fan contactor *) (* 0*)
Err231水泵接触器(* Water pump contactor *) (* 0*)
Err232从站PLC检测从站通讯错误(* Slave communication failure detected
Err233主站PLC检测主站通讯错误(* Slave communication failure detected Err234齿轮箱低速泵接触器(* Gearbox low speed pump contactor *) ( Err235齿轮箱高速泵接触器(* Gearbox high speed pump contactor *) Err236驱动侧振动AC加速度传感器(* Acceleration sensor AC drive side *) Err237非驱动侧振动AC加速度传感器(* Acceleration sensor AC non-drive side Err238保留(* Reserve *) (* 0*)
Err239保留(* Reserve *) (* 0*)
Err240保留(* Reserve *) (* 0*)
Err241驱动列摇摆(* Drive train swinging *) (* 4*)
Err242塔架移动驱动侧(* Tower movement drive side *) (* 4*) Err243塔架移动非驱动侧(* Tower movement non-drive side *) (* 4 Err244齿轮箱压力传感器(* Gearbox pressure sensor *) (* 0*)
Err245驱动侧振动DC加速度传感器(* Acceleration sensor DC drive side *) Err246非驱动侧振动DC加速度传感器(* Acceleration sensor DC non-drive side Err2471000秒内机舱摆动警告3次(* 3 nacelle swinging warning in 1000s * Err248一分钟内定子电流过滤值太高(* Stator current filtered in 1min too h Err249一分钟内总电流过滤值过高(* Total current filtered in 1min too hi Err250偏航定位系统-左/右位被转换(* Yaw position system - Left/Right bit Err251电网功率10分钟内过滤值过高(* Grid power filtered in 10min too high Err252电网功率1分钟内过滤值过高(* Grid power filtered in 1min too high Err253电网功率10秒内过滤值过高(* Grid power filtered in 10s too high * Err254移动时偏航功率低于错误极限值(* Yaw power below error limit at moving Err255保留(* Reserve *) (* 0*)
power converter *) (* 6*)
ed converter reset *) (* 0*)
dentification number not correct *) (* 0*) versions not correct *) (* 0*)
ersion not correct *) (* 0*)
ion, hub doesn't reach state stop *) (* 0*) ware version not correct *) (* 0*)
nacelle can't be found *) (* 0*)
ted *) (* 3*)
y button *) (* 3*)
r over speed *) (* 2*)
n sensor *) (* 2*)
er speed *) (* 5*)
*) (* 2*)
sition *) (* 2*)
position exceeded *) (* 2*)
ves *) (* 2*)
relay not reset *) (* 2*)
nal cabinet *) (* 0*)
nal cabinet *) (* 0*)
r not at the CANbus *) (* 6*)
by power converter *) (* 6*)
ifferes to demanded *) (* 0*)
meter *) (* 0*)
10 not at bus *) (* 2*)
e not at bus *) (* 0*)
contactor 690V *) (* 0*)
iaries *) (* 0*)
pitch1 *) (* 2*)
pitch2 *) (* 2*)
pitch3 *) (* 2*)
ed rotor for brake *) (* 5*)
e blades error *) (* 5*)
orage relays *) (* 5*)
t Stop *) (* 0*)
t Reference *) (* 0*)
bility *) (* 2*)
t Stop *) (* 0*)
t Reference *) (* 0*)
bility *) (* 2*)
t Stop *) (* 0*)
t Reference *) (* 0*)
bility *) (* 2*)
e box connected *) (* 2*)
error *) (* 2*)
e box connected *) (* 2*)
error *) (* 2*)
e box connected *) (* 2*)
error *) (* 2*)
n error delayed *) (* 0*)
n error delayed *) (* 0*)
n error delayed *) (* 0*)
s not synchronous slow *) (* 0*)
s not synchronous fast *) (* 0*)
eed not set to the rated maximum *) (* 2*)
ce positioning error *) (* 0*)
ce positioning error *) (* 0*)
ce positioning error *) (* 0*)
ng switch not active in stop_ok state *) (* 2*) ng switch not active in stop_ok state *) (* 2*) ng switch not active in stop_ok state *) (* 2*) ng switch not active in safety_ok state *) (* 2*) ng switch not active in safety_ok state *) (* 2*) ng switch not active in safety_ok state *) (* 2*) out high speed *) (* 2*)
out low speed *) (* 2*)
out high speed *) (* 2*)
out low speed *) (* 2*)
top timeout high speed *) (* 5*)
top timeout low speed *) (* 2*)
asurement *) (* 0*)
asurement *) (* 0*)
voltage in precharge *) (* 0*)
der feedback *) (* 0*)
ncoder feedback *) (* 0*)
tuation error limit *) (* 0*)
re at no pumping *) (* 0*)
x heating *) (* 0*)
y charging *) (* 0*)
*) (* 0*)
ce rotor speed signals *) (* 0*)
speed relais 1 *) (* 2*)
speed relais 2 *) (* 2*)
emergency stop button *) (* 3*)
emergency stop button *) (* 3*)
cy stop button *) (* 3*)
y extremly high or not connected *) (* 0*) temperature *) (* 0*)
enerator overhang *) (* 0*)
enerator overhang *) (* 0*)
enerator overhang *) (* 0*)
enerator bearing drive *) (* 0*)
enerator bearing non drive *) (* 0*) earbox bearing *) (* 0*)
earbox oil *) (* 0*)
y extremly low or not connected *) (* 0*) ature high *) (* 0*)
ature sensor defect *) (* 0*)
mperature high *) (* 0*)
r at line side converter *) (* 0*)
d not reached *) (* 0*)
mperature too high *) (* 0*)
nerator overhang *) (* 0*)
nerator bearing *) (* 0*)
arbox oil *) (* 0*)
celle cabinet *) (* 0*)
arbox bearing *) (* 0*)
> 2 mm *) (* 0*)
pressure *) (* 0*)
ot detected by safety chain *) (* 2*)
vel too low *) (* 0*)
mperature > 90鳦 *) (* 0*)
r brake pump *) (* 0*)
rotection limit low *) (* 0*)
rotection limit high *) (* 6*)
ailed three times, low voltage *) (* 0*) rotection signal cut *) (* 0*)
on change during stand still *) (* 0*)
e adjust *) (* 0*)
on exceeded *) (* 0*)
rter *) (* 0*)
current DC supply *) (* 0*)
ition not reached *) (* 0*)
r gearbox high speed *) (* 0*)
tch not set in automatic mode *) (* 2*)
fect *) (* 2*)
on *) (* 0*)
fault *) (* 0*)
r gearbox low speed *) (* 0*)
ce small rotor speed *) (* 0*)
ce generator speed too small *) (* 4*)
el high *) (* 4*)
el low *) (* 4*)
peed pump no pressure *) (* 0*)
cted by battery *) (* 0*)
e in nacelle position is too small *) (* 0*)
age difference battery test *) (* 0*)
generator signal *) (* 4*)
not synchronise *) (* 0*)
surement error. *) (* 0*)
l zero for 9h *) (* 0*)
munication error *) (* 0*)
attery temperature *) (* 0*)
w temperature *) (* 0*)
e too lowstandby or refresh state *) (* 0*)
w converter connected *) (* 0*)
ion > 30 kW *) (* 0*)
not on CAN-BUS *) (* 0*)
he nacelle positionmoving of yaw *) (* 0*)
230V *) (* 0*)
r water pump *) (* 0*)
r water valve at converter cabinet inlet *) (* 0*) ke 230V *) (* 0*)
data multiplexer not OK *) (* 0*)
r crowbar *) (* 0*)
ifference DC bus voltage pitch and batterie voltage *) (* 0*) imeout pitch move to demanded position *) (* 0*)
itch not move back at open safety chain *) (* 5*)
rake not closed *) (* 0*)
rake pressure *) (* 0*)
nemometer not plausible *) (* 0*)
itch not moved back by battery *) (* 0*)
atteries didn't detect grid loss *) (* 0*)
riction bearing too high *) (* 0*)
tal discharging, contactor *) (* 0*)
st activation, contactor *) (* 0*)
0V contactor1 *) (* 0*)
0V contactor2 *) (* 0*)
ly 500V DC not closed *) (* 0*)
ans *) (* 0*)
relays 230V supply *) (* 0*)
emperature *) (* 0*)
t heating *) (* 0*)
error *) (* 0*)
tactor *) (* 0*)
munication failure watchdog *) (* 0*)
e temperature *) (* 0*)
ntactor *) (* 0*)
tactor *) (* 0*)
ation failure detected by slave PLC *) (* 2*)
ation failure detected by master PLC *) (* 2*) eed pump contactor *) (* 0*)
peed pump contactor *) (* 0*)
ensor AC drive side *) (* 0*)
ensor AC non-drive side *) (* 0*)
inging *) (* 4*)
drive side *) (* 4*)
non-drive side *) (* 4*)
re sensor *) (* 0*)
ensor DC drive side *) (* 0*)
ensor DC non-drive side *) (* 0*)
ging warning in 1000s *) (* 0*)
filtered in 1min too high *) (* 0*)
filtered in 1min too high *) (* 0*)
ystem - Left/Right bit inverted *) (* 0*) tered in 10min too high *) (* 0*)
tered in 1min too high *) (* 0*)
tered in 10s too high *) (* 0*)
w error limit at moving *) (* 0*)。