MOXA交换机使用说明
MOXA交换机使用说明教学内容
MOXA交换机使用说明教学内容一、简介MOXA交换机是一种高性能的工业以太网交换机，它能够满足工业环境中对网络可靠性和稳定性的要求。
MOXA交换机具有多个端口，支持各种网络协议，并具有多种网络管理和优化功能。
本教程将介绍如何正确使用MOXA交换机，并详细说明其各项功能。
二、安装与配置1.检查交换机是否损坏：确认交换机外观是否完好，是否有明显的损坏或缺陷。
2.连接电源：将交换机的电源插头插入电源插座，然后按下开关，确认交换机的指示灯是否亮起。
3.连接设备：使用网线将设备与交换机的端口相连。
4.配置网络参数：使用电脑连接至交换机的管理端口，通过浏览器登录交换机的配置界面，根据需要配置网络参数，如IP地址、子网掩码等。
5.网络测试：在配置完成后，使用网络测试工具对交换机进行测试，确认网络连接正常。
三、交换机配置1.VLAN配置：VLAN是一种将交换机端口划分为不同虚拟局域网的技术。
在交换机中配置VLAN，可以实现不同设备之间的隔离和通信。
2. QoS配置：QoS（Quality of Service）是一种网络优化技术，通过分配带宽和优先级，可以保证关键应用的网络传输质量。
3.静态路由配置：在交换机中配置静态路由，可以实现不同子网之间的通信。
4.端口管理：配置端口速率、全双工或半双工模式、流控等参数，以充分利用网络带宽和提高网络性能。
5.网络监控与诊断：通过交换机的网络监控功能，可以实时监测网络流量、连接状态和端口的状态，以及进行故障诊断和排除。
四、安全性配置1.密码设置：修改交换机的默认登录密码，以保护设备免受未经授权的访问。
2. 限制访问：通过配置ACL（Access Control List）或MAC过滤，限制特定IP地址或MAC地址的访问。
3.HTTPS加密：将交换机的管理界面配置为使用HTTPS加密协议，提高数据传输的安全性。
4.日志记录：开启日志记录功能，记录交换机的操作和事件，以便后续分析和审计。
MOXA NPort_5610配置说明
MOXA NPort_5610配置说明1.设置IP地址：1)给设备接上电源；2)在正面液晶屏处按SEL按钮，并通过∧或∨按钮选择到年Network setting，按SEL按钮进入；3)在通过∧或∨按钮选择到IP address，按SEL按钮进入；4)通过∧或∨和SEL按钮设置正确的IP地址，设置完后按MENU按钮退到最外的菜单；5)对提示SA VE，通过∧或∨按钮选择Yes并按SEL按钮；6)等装置自动重新启动，查看液晶屏上现实的IP地址是否正确；2.配置端口设置：1)将设备背面的LAN口用网线连接到交换机；2)使用网内的一台计算机，打开IE浏览器，在浏览器地址中输入MOXA装置的IP地址；3)在左侧列表中选择Operating Settings菜单下的Port1，在右侧选项中，把端口模式选择到UPD Server，在Local TCP Port处输入与对应IOLANE端口一样的端口号，再选择Submit按钮。
然后依次再左侧选择Port2一直到Port16，重复之前的操作；4)再通过IE浏览器访问到设备界面，选择左侧的Serial Settings菜单下的Port1，在右侧Baud rate中选择该端口对应厂站的波特率，在Flow control中选择None，再选择Submit按钮。
然后依次再左侧选择Port2一直到Port16，重复之前的操作；5)最后选择左侧的Save/Restart菜单，选择其中的Save and Restart，等待设备自动重启完毕；3.完成以上操作后，MOXA基本就配置好了。
Parity 要改成EVEN。
数据才上的来。
申瑞杨卿13:59:32哦，因为101规约是需要设置为偶校验方式的申瑞杨卿13:59:38EVEN就是表示偶校验通讯校验方式总结：1. even 每个字节传送整个过程中bit为1的个数是偶数个（校验位调整个数）2. odd 每个字节穿送整个过程中bit为1的个数是奇数个（校验位调整个数）3. noparity没有校验位4. space 校验位总为05. mark 校验位总为1；。
MOXA交换机使用说明教学内容
M O X A交换机使用说明MOXA交换机使用说明1、IP地址的设置通过IE工具来Ping 交换机默认的IP(出厂默认192.168.127.253)地址，进入交换机配置界面后，直接点击确认后，进入交换机设置界面对话框，IP地址设置请选择\Main Meun\Basic Settings\Network，出现下列对话框在此对话框下，设置人员在Switch IP Address 和 Switch Subnet Mask 旁的空白处填写预定的IP地址（如：192.168.12.20），以及相应的子网掩码地址（如：255.255.255.0）；其他的如Auto IP Configuration 设置为Disable方式，不要选择HDCP方式。
2、主站（Master）设置完成了IP方式的设置后，就需要对交换的通讯协议和交换机进行相应的设置，选择\Main Menu\Communication Redundancy（通讯冗余设置），进入对话框：在此对话框内，我们需要注意的是Settings标记下方的设置参量，而Current Status为相应的设置参量后交换机系统检测后的状态指示。
Redundancy Protocol （通讯协议设置）：设置选择为Turbo Ring ，而非是IEEE802协议（快速生成树）方式；采用Turbo Ring方式的情况下，需要在网络交换机组中设置一个Master（主站），选择主站的方式是将Set as Master前的小方框内给予选中, 只需要选择确定后，点击Activate按钮即可生效。
（注意：在多个交换机组成网中只能有1个设置为Master，不可以多选；同时如果不对交换机进行Master设置，系统会自动设置交换机组中的1台为Master）。
Enable Ring Coupling （环间耦合端口定义）在实际的项目运用中不常运用到，在此不给予更多的描述。
需要提醒的是工程人员在设置过程中不要将Enable Ring Coupling前的小方格选中，同时要注意的是对应的Coupling Port和 Coupling Control Port后的端口与前面的Redundant Ports 1st Port和 2nd Port（冗余连接端口定义）设置的端口重复。
MOXA交换机使用说明
MOXA接换机使用证明之阳早格格创做1、IP天面的树立通过IE工具去Ping 接换机默认的IP(出厂默认192.168.127.253)天面，加进接换机摆设界里后，间接面打确认后，加进接换机树立界里对付话框，IP天面树立请采用\Main Meun\Basic Settings\Network，出现下列对付话框正在此对付话框下，树立人员正在Switch IP Address 战Switch Subnet Mask 旁的空黑处挖写预约的IP天面（如：192.168.12.20），以及相映的子网掩码天面（如：255.255.255.0）；其余的如Auto IP Configuration 树立为Disable办法，没有要采用HDCP办法.2、主站（Master）树立完毕了IP办法的树立后，便需要对付接换的通讯协媾战接换机举止相映的树立，采用\Main Menu\Communication Redundancy（通讯冗余树立），加进对付话框：正在此对付话框内，咱们需要注意的是Settings标记表记标帜下圆的树立参量，而Current Status为相映的树立参量后接换机系统检测后的状态指示.Redundancy Protocol （通讯协议树立）：树立采用为Turbo Ring ，而非是IEEE802协议（赶快死成树）办法；采与Turbo Ring办法的情况下，需要正在搜集接换机组中树立一个Master（主站），采用主站的办法是将Set as Master前的小圆框内赋予选中, 只需要采用决定后，面打Activate按钮即可死效.（注意：正在多个接换机组成网中只可有1个树立为Master，没有成以多选；共时如果分歧过失接换机举止Master树立，系统会自动树立接换机组中的1台为Master）.Enable Ring Coupling （环间耦合端心定义）正在本质的名目使用中没有常使用到，正在此没有赋予更多的形貌.需要指示的是工程人员正在树立历程中没有要将Enable Ring Coupling前的小圆格选中，共时要注意的是对付应的Coupling Port战Coupling Control Port后的端心与前里的Redundant Ports 1st Port战 2nd Port（冗余对接端心定义）树立的端心沉复.3、搜集树立参数考证完毕搜集参数树立后，对付应的Communication Redundancy对付话框内皆通过Current Status状态赋予体现了，包罗了搜集协议状态、主（Master）/从（Slave）办法；冗余端心的数据监测状态以及环间耦合状态疑息.正在多台接换机组环的情况下，工程人员要注意Redundant Ports 1st Port战2nd Port（冗余端心状态监测状态）的疑息：（1）、Forwarding:（促成状态）表示接换机的处事状态平常，二个搜集冗余对接端心的数据进程宁静.（2）、Link Down：（断线状态）表示接换机于相映的对接心对接的数据线存留问题，引导系统监测到为断线状态，需要工程人员举止查看.（3）、Blocked:（中断状态）此状态为平常情景，果为Turbo Ring办法正在物理上以环的形式存留，而正在接换机搜集接换时，是通过一面的Blocked标记表记标帜去标注环网的假制末面，以决定其数据流背的末面.（4）、Learning：（侦听状态）此状态正在搜集出现了断线战回复的历程中，后备线路的接换机会出现侦听状态，正在稳态的情况下，接换机没有会出现此疑息.正在参数树立完毕战搜集回复佳后，请查看各接换机的冗余端心状态，平常情景为惟有1台接换机的1个端心处于Blocked状态，其余接换机及其端心为Forwarding状态.4、搜集尝试考证对付于搜集接换机及搜集线树立对接完毕后，请工程人员测验考查将搜集冗余线的环赋予断启，以考证搜集接换机的运止处事情景怎么样.5、闭于冗余心的对接办法（1）、齐电心的接换机的对接：诸如408A系列中齐电心的，精确的冗余端心对接办法为：端心7与端心8对接，接互对接产死环形办法.（2）、光心型接换机的对接办法，诸如：408A、516A系列中SC（ST）型号的设备，精确的冗余端心对接办法如下：光心接换机1的T1对接光心接换机2的R2，R1对接T2，T2对接R1，R2对接T1；多台接换依此对接办法逆延对接，并最后产死环形结构.依照非平常办法对接，肯定会制成搜集回路的非冗余，共时极有大概果搜集数据接换的果素引导搜集没有宁静或者搜集风暴局里出现，请诸位工程人员庄重遵照精确要领举止对接.。
MOXA交换机使用说明
MOXA交换机使用说明1、IP地址的设置通过IE工具来Ping 交换机默认的IP(出厂默认192、168、127、253)地址,进入交换机配置界面后,直接点击确认后,进入交换机设置界面对话框,IP地址设置请选择\Main Meun\Basic Settings\Network,出现下列对话框在此对话框下,设置人员在Switch IP Address 与 Switch Subnet Mask 旁的空白处填写预定的IP地址(如:192、168、12、20),以及相应的子网掩码地址(如:255、255、255、0);其她的如Auto IP Configuration 设置为Disable方式,不要选择HDCP方式。
2、主站(Master)设置完成了IP方式的设置后,就需要对交换的通讯协议与交换机进行相应的设置,选择\Main Menu\Communication Redundancy(通讯冗余设置),进入对话框:在此对话框内,我们需要注意的就是Settings标记下方的设置参量,而Current Status 为相应的设置参量后交换机系统检测后的状态指示。
Redundancy Protocol (通讯协议设置):设置选择为Turbo Ring ,而非就是IEEE802协议(快速生成树)方式;采用Turbo Ring方式的情况下,需要在网络交换机组中设置一个Master(主站),选择主站的方式就是将Set as Master前的小方框内给予选中, 只需要选择确定后,点击Activate按钮即可生效。
(注意:在多个交换机组成网中只能有1个设置为Master,不可以多选;同时如果不对交换机进行Master设置,系统会自动设置交换机组中的1台为Master)。
Enable Ring Coupling (环间耦合端口定义)在实际的项目运用中不常运用到,在此不给予更多的描述。
需要提醒的就是工程人员在设置过程中不要将Enable Ring Coupling 前的小方格选中,同时要注意的就是对应的Coupling Port与 Coupling Control Port后的端口与前面的Redundant Ports 1st Port与 2nd Port(冗余连接端口定义)设置的端口重复。
MOXA EDS-P510 系列 Gigabit 网管型备用 Ethernet 交换机说明书
EDS-P510系列7+3G埠Gigabit PoE+網管型乙太網路交換器含4個IEEE802.3af PoE連接埠特色與優點•4個符合IEEE802.3af標準的PoE和乙太網路複合連接埠•每個PoE連接埠在48VDC時可提供最高15.4瓦電力•智慧耗電量偵測、PD故障檢查以及PoE排程功能。
•3個複合（10/100/1000BaseT(X)或100/1000BaseSFP插槽）Gigabit連接埠；2個用於備援環網的連接埠以及1個用於uplink的連接埠•支援Turbo Ring和Turbo Chain（復原時間<20毫秒@250台交換器），以及透過RSTP/STP和MSTP協議支援網路備援•支援Mxstudio以進行輕鬆、虛擬化的工業網路管理•V-ON™可確保毫秒等級的multicast資料和視訊網路復原認證簡介EDS-P510系列Gigabit網管型備援乙太網路交換器有4個10/100BaseT(X)802.3af(PoE)相容的乙太網路連接埠以及3個複合Gigabit乙太網路連接埠。
EDS-P510交換器每PoE連接埠可提供高達15.4瓦電力，並且在不易取得交流電源或當地供應成本過高時，提供PoE電力至連接裝置（例如監控攝影機、無線存取點以及IP電話）。
EDS-P510交換器用途極為廣泛，其SFP光纖連接埠可將資料從裝置傳輸至控制中心（最遠可達80公里），並且具有高度EMI抗擾性。
乙太網路交換器支援先進的管理與安全功能。
EDS-P510系列是專門為安全自動化應用（例如IP監控和進入系統閘門）所設計，此類應用能夠藉由可擴充的骨幹結構與PoE獲益。
附加特色與優點•進階PoE管理功能（PoE連接埠設定、PD故障檢查以及PoE排程）•命令列介面(CLI)快速設定主要網管功能•DHCP Option82依據不同的政策配置IP位置•支援EtherNet/IP和Modbus TCP通訊協定以進行裝置管理與監控•支援Turbo Ring和Turbo Chain（復原時間<20毫秒@250台交換器），以及透過RSTP/STP和MSTP協議支援網路備援•IGMP和GMRP，用於篩選multicast流量•以連接埠為基礎的VLAN、IEEE802.1Q VLAN以及GVRP，用來簡化網路規劃•QoS(IEEE802.1p/1Q)和TOS/DiffServ以提高確定性•Port Trunking可提供最佳頻寬使用率•支援TACACS+、IEEE802.1X、SNMPv3、HTTPS和SSH，強化網路安全•鎖定連接埠功能可根據MAC位址封鎖未經授權的存取•SNMPv1/v2c/v3，適用不同層級的網路管理•RMON提供有效率的網路監視與主動式功能•頻寬管理可預防無法預測的網路狀態•可用連線埠鏡像進行線上除錯•發生例外狀況時透過電子郵件和繼電器輸出自動發出警告規格Ethernet InterfaceCombo Ports(10/100/1000BaseT(X)or100/ 1000BaseSFP+)3Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection10/100BaseT(X)Ports(RJ45connector)3Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connectionPoE Ports(10/100BaseT(X),RJ45connector)4Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connectionStandards IEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1X for authenticationIEEE802.3for10BaseTIEEE802.3ab for1000BaseT(X)IEEE802.3ad for Port Trunk with LACPIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.3z for1000BaseSX/LX/LHX/ZXIEEE802.3af for PoEEthernet Software FeaturesFilter GMRP,GVRP,IGMP v1/v2,Port-based VLANIndustrial Protocols EtherNet/IP,Modbus TCPManagement Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Flow control,IPv4/IPv6,LLDP,Port Mirror,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTPMIB Bridge MIB,Ethernet-like MIB,MIB-II,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols LACP,Link Aggregation,MSTP,RSTP,STP,Turbo Chain,Turbo Ring v1/v2Security TACACS+,HTTPS/SSL,Port Lock,RADIUS,SSHTime Management NTP Server/Client,SNTPInput/Output InterfaceAlarm Contact Channels2,Relay output with current carrying capacity of1A@24VDCDigital Input Channels2Digital Inputs-30to+3V for state0+13to+30V for state1Max.input current:8mASwitch PropertiesIGMP Groups1024MAC Table Size8KMax.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094Serial InterfaceConsole Port RS-232(TxD,RxD,GND),10-pin RJ45(19200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Current 1.5A@48VDCInput Voltage48VDC,Redundant dual inputsOperating Voltage44to57VDCOverload Current Protection SupportedPower Budget Max.15.4W for each PoE portMax.61.6W for total PD consumptionPower Consumption(Max.)Max.14.24W full loading without PDs’consumption Reverse Polarity Protection SupportedPhysical CharacteristicsDimensions80.2x135x105mm(3.16x5.31x4.13in) Housing MetalInstallation DIN-rail mounting,Wall mounting(with optional kit) IP Rating IP30Weight1,170g(2.58lb)Environmental LimitsAmbient Relative Humidity5to95%(non-condensing)Operating Temperature EDS-P510:0to60°C(32to140°F)EDS-P510-T:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Standards and CertificationsSafety UL508EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFMaritime ABS,DNV-GL,LR,NKFreefall IEC60068-2-31Shock IEC60068-2-27Vibration IEC60068-2-6MTBFTime205,384hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /tw/warrantyPackage ContentsDevice1x EDS-P510Series switchCable1x DB9female to RJ4510-pinInstallation Kit8x cap,plastic,for RJ45port3x cap,plastic,for SFP slotDocumentation1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x quick installation guide1x warranty cardNote SFP modules need to be purchased separately for use with this product.尺寸訂購資訊Model NameCombo Ports10/100/1000BaseT(X)or100/1000BaseSFPPoE Ports10/100BaseT(X)non-PoE Ports10/100BaseT(X)Operating Temp.EDS-P510343-10to60°C EDS-P510-T343-40to75°C 配件（選購）Storage KitsABC-02-USB Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,0to60°C operating temperatureABC-02-USB-T Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,-40to75°C operating temperatureSFP ModulesSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1FEMLC-T SFP module with1100Base multi-mode with LC connector for4km transmission,-40to85°C operatingtemperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°C operatingtemperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for500m transmission,0to60°C operatingtemperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for500m transmission,-40to85°C operatingtemperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300/550m transmission,0to60°C operatingtemperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperaturePower SuppliesDR-120-48120W/2.5A DIN-rail48VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-75-4875W/1.6A DIN-rail48VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureDRP-240-48DIN-rail48VDC power supply with240W/5A,85to264VAC,or120to370VDC input,-10to70°Coperating temperatureSDR-480P-48DIN-rail48VDC power supply with480W/10A,90to264VAC,or127to370VDC input,(current sharingup to3840W),-25to70°C operating temperatureWall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kitSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.版權所有.2019年10月31日更新。
MOXA交换机设置VLAN说明
MOXA交换机设置VLAN说明李俊格访问MOXA交换机有三种方式：RS-232串口控制台，远程控制台和Web浏览器。
串口控制台连接方法就是用串口线将EDS-726连接到PC机的COM口，可以在不知道其IP地址的情况下使用。
而远程控制台和Web浏览器方式可用于在局域网或Internet中访问MOXA。
一、用超级终端连接交换机。
1）将自己的超级终端设置成如下模式：115200-8-N-1,模式选择VT100,一般默认都是VT100，设置完成后，用交换机自带的调试线与MOXA的CONSOLE网口连接。
2）连接成功后，如图，输入1，回车。
3）在Account行回车，选择用户名，一般就是admin，不用变，用小键盘的“下”将光标移至Password行，初始密码为空，回车。
4）登陆成功，界面如下所示，可以通过移动光标来改相应的设置，我们一般只需改VLAN相关，就是第六项。
5）在VLAN port setting下面改每个口的VLAN状态。
如图所示，交换机的每一个port都有好几个属性，交换机的默认管理VLAN是1，只有VLAN为1的口才能通过网络进行访问管理，这个不需要改动。
所以我们设置的A\B网VLAN就要避开1，现在一般A网设置10，B网设置20，当然也可以自己整定。
Type有两个选项：1、Access：该端口类型用来连接单个设备而不需要标记。
2、Trunk：该端口类型用来连接另一个交换机和另一个LAN，将标记设备和未标记设备和别的交换机和HUB联系起来。
PVID：该端口默认的访问VLAN ID。
Fixed VLAN （Tagged）：只有当端口类型选择为Trunk时该栏才被激活，给连接到Trunk 端口的标记设备设置其他的VLAN ID，用逗号区分不同的VID。
如图该项写了20，当通过该口的GOOSE报文具有标记20时，该口将这帧报文直接转给VLAN ID为20的VLAN 网络；当通过报文标记是20，10以外的其他数值时，该口强行将这帧报文的标记置为10，然后转给VLAN ID为10的VLAN网络。
MOXA交换机使用说明
MOXA交换机使用说明1、IP地址的设置通过IE工具来Ping 交换机默认的IP(出厂默认192.168.127.253)地址，进入交换机配置界面后，直接点击确认后，进入交换机设置界面对话框，IP地址设置请选择\Main Meun\Basic Settings\Network，出现下列对话框在此对话框下，设置人员在Switch IP Address 和 Switch Subnet Mask 旁的空白处填写预定的IP地址（如：192.168.12.20），以及相应的子网掩码地址（如：255.255.255.0）；其他的如Auto IP Configuration 设置为Disable方式，不要选择HDCP方式。
2、主站（Master）设置完成了IP方式的设置后，就需要对交换的通讯协议和交换机进行相应的设置，选择\Main Menu\Communication Redundancy（通讯冗余设置），进入对话框：在此对话框内，我们需要注意的是Settings标记下方的设置参量，而Current Status为相应的设置参量后交换机系统检测后的状态指示。
Redundancy Protocol （通讯协议设置）：设置选择为Turbo Ring ，而非是IEEE802协议（快速生成树）方式；采用Turbo Ring方式的情况下，需要在网络交换机组中设置一个Master（主站），选择主站的方式是将Set as Master前的小方框内给予选中, 只需要选择确定后，点击Activate按钮即可生效。
（注意：在多个交换机组成网中只能有1个设置为Master，不可以多选；同时如果不对交换机进行Master设置，系统会自动设置交换机组中的1台为Master）。
Enable Ring Coupling （环间耦合端口定义）在实际的项目运用中不常运用到，在此不给予更多的描述。
需要提醒的是工程人员在设置过程中不要将Enable Ring Coupling 前的小方格选中，同时要注意的是对应的Coupling Port和 Coupling Control Port后的端口与前面的Redundant Ports 1st Port和 2nd Port（冗余连接端口定义）设置的端口重复。
MOXA交换机环网配置图解说明EDS-408A-MM-SC
打开MOXA交换机光盘中自带的edscfgui.exe配置工具(EDS-408A/utility/edscfgui.exe 目录)
点击List Server -> Broadcast Search，软件自动开始搜索当前网络内联网的交换机
选中当前交换机，点击右键菜单中的Modify IP Address一项，弹出交换机IP修改对话框。
在IP Address一项前面打勾，并将交换机IP修改成需要的值。
确定后弹出警告对话框，选择yes即可。
依次将环网内的所有交换机IP设置在同一网段，如192.168.0.xxx
修改本地电脑的IP地址，使其与交换机的当前IP在同一网段下如192.168.0.32。
这时才能通过IE浏览器访问交换机。
打开左边的communication redundancy菜单项，右边画面出现网络协
EDS-408A系列最新firmware版本支持Turbo Ring V2，相对于V1
请注意Enable Ring Coupling环间耦合功能不启用，所以在前面方框中不要勾选。
moxa交换机环网配置图解说明
如对您有帮助，请购买打赏，谢谢您！MOXA交换机环网配置说明（以EDS-508-MM-SC为例）1．打开MOXA edscfgui.exe配置工具，通过broadcast方式搜索网络中的所有MOXA网管型交换机。
2. 通过搜索框可查看到网路中的交换机相关信息。
3. 左键选中其中一台交换机，右边出现该台交换机的详细信息。
包括型号、名称、IP配置、物理地址、串列号、固件版本等。
当有多台交换机IP地址冲突时，每台交换机会按照接入网络的次序相应叠加，自动改变IP地址。
因此我们要对所有的交换机重新配置IP。
4. 选中某台交换机后，点击右键，进入弹出菜单中的Modify IP Address，可通过如下方式修改交换机IP。
如此配置好每台交换机IP并刷新显示列表。
5.有的时候我们可以通过firmware固件版本的升级，来更新交换机软件功能：选中某台交换机后，点击菜单栏Firmware->upgrade，选择firmware升级文件后确定。
6. 确定后系统开始更新该台交换机的firmware版本。
7. Progress信息栏显示OK，firmware升级完成。
8.接下来介绍页面配置。
可直接在IE浏览器中输入相应交换机IP地址访问，也可通过右键菜单中的Web Console进入配置页面。
9. 初次访问交换机时，默认用户名为admin,密码为空，直接点击login进入。
10.页面中上面为交换机信息，左半部分为交换机配置菜单，右边为子菜单内容。
进入Basic Settings的Network,右边显示交换机本身的网络配置。
可在此处更新IP，修改后必须点击Activate激活。
11．进入Communication Redundancy菜单，选择Turbo Ring环网方式或RSTP生成树网络结构。
点击Turbo Ring后，在下面选好Redundant Ports,即用于组环的两个交换机端口号。
(a)若该台交换机是这个环网中的master，则在Set as Master前打勾选中。
moxa交换机设置指导
产品型号 MAC地址 Fault 环网状态
IP地址 电源状态 Firmware Version
System 系统识别 Password 访问密码 Port 端口传输速率、流量控制及端口类型 Network 网络设置 Local Import/Export 系统文件、日志导入/导出；Firmware升级 Restart 设备重启 Factory Default 恢复出厂参数
Traffic Prionitization 数据优先级
Virtual Lan
虚拟局域网
Multicast Filtering
组播过滤
Bandwidth Management 带宽管理
Auto Warning
自动告警
Diagnosis
诊断
System Log
系统日志
设置界面
IP地址设置 环网设置
IP地址设置
MOXA交换机搜索软件
设置界面
IP地址设置
环网设置
端口镜像 系统检测 事件记录
环网设置步骤1
Communication Redundancy
环网设置步骤2
环网设置步骤3
步骤说明
从上图我们找到“communication Redundancy” 选项，在右边的下拉菜单中选择环网协议或turbo ring v2， 备注：Turboring与Turboring V2这两个协议之间 不兼容，请确定所有交换机的环网协议要相同一致， 要么全是Turboring，要么全是Turboring V2
进入配置界面方式
Telnet远程控制台配置
RS-232 Console控制台
Web浏览器配置
Moxa MDS-G4020-L3系列模块交换机说明书
MDS-G4020-L3Series20G-port Layer 3full Gigabit modular managed Ethernet switchesFeatures and Benefits•Layer 3routing interconnects multiple LAN segments •Multiple interface type 4-port modules for greater versatility•Tool-free design for effortlessly adding or replacing modules without shuttingdown the switch•Ultra-compact size and multiple mounting options for flexible installation •Rugged die-cast design for use in harsh environments•Intuitive,HTML5-based web interface for a seamless experience acrossdifferent platformsCertificationsIntroductionThe MDS-G4020–L3Series modular switches support up to 20Gigabit ports,including 4embedded ports,4interface module expansion slots,and 2power module slots to ensure sufficient flexibility for a variety of applications.The highly compact MDS-G4000–L3Series is designed to meet evolving network requirements,ensuring effortless installation and maintenance,and features a hot-swappable module design that enables you to easily change or add modules without shutting down the switch or interrupting network operations.The multiple Ethernet modules (RJ45,SFP,and PoE+)and power units (24/48VDC,110/220VAC/VDC)provide even greater flexibility as well as suitability for different operating conditions,delivering an adaptive full Gigabit platform that provides the versatility and bandwidth necessary to serve as an Ethernet aggregation/edge switch.Featuring a compact design that fits in confined spaces,multiple mounting methods,andconvenient tool-free module installation,the MDS-G4000–L3Series switches enable versatile and effortless deployment without the need for highly skilled engineers.With multiple industry certifications and a highly durable housing,the MDS-G4000Series can reliably operate in tough and hazardous environments such as power substations,mining sites,ITS,and oil and gas applications.Support for dual power modules provides redundancy for high reliability and availability while LV and HV power module options offer additional flexibility to accommodate the power requirements of different applications.Support for Layer 3routing functionality enables these switches to facilitate the deployment of applications across different networks,making them ideal for large-scale industrial networks.In addition,the MDS-G4000–L3Series features an HTML5–based,user-friendly web interface providing a responsive,smooth user experience across different platforms and browsers.SpecificationsEthernet InterfacePre-installed Modules 4embedded Gigabit portsModule4slots for optional 4-port FE/GE modulesSlot Combination See the LM-7000H module series datasheet for more information.Note:The required power module depends on the choice of LM-7000H module.Refer tothe following power/module combination requirements.LM-7000H non-PoE modules:Any power moduleLM-7000H PoE modules:PWR-HV-P48,PWR-LV-P48onlyStandards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3ab for1000BaseT(X)IEEE802.3z for1000BaseXIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPIEEE802.1Q for VLAN TaggingIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1X for authenticationIEEE802.3af/at for PoE/PoE+outputEthernet Software FeaturesManagement IPv4/IPv6,Flow control,Back Pressure Flow Control,DHCP Server/Client,ARP,RARP,LLDP,Port Mirror,Linkup Delay,SMTP,SNMP Trap,SNMP Inform,SNMPv1/v2c/v3,RMON,TFTP,SFTP,HTTP,HTTPS,Telnet,Syslog,Private MIB,Loopback interface Filter GMRP,GVRP,GARP,802.1Q VLAN,IGMP Snooping v1/v2/v3,IGMP Querier Redundancy Protocols STP,RSTP,Turbo Ring v2,Turbo Chain,Ring Coupling,Dual-Homing,Link Aggregation Routing Redundancy VRRPSecurity Broadcast storm protection,Rate Limit,Trust access control,Static Port Lock,MACSticky,HTTPS/SSL,SSH,RADIUS,TACACS+,Login and Password PolicyTime Management SNTP,NTP Server/Client,NTP AuthenticationProtocols IPv4/IPv6,TCP/IP,UDP,ICMP,ARP,RARP,TFTP,DNS,NTP Client,DHCP Server,DHCP Client,802.1X,QoS,HTTPS,HTTP,Telnet,SMTP,SNMPv1/v2c/v3,RMON,SyslogUnicast Routing OSPF,Static RouteMIB P-BRIDGE MIB,Q-BRIDGE MIB,IEEE8021-SPANNING-TREE-MIB,IEEE8021-PAE-MIB,IEEE8023-LAG-MIB,LLDP-EXT-DOT1-MIB,LLDP-EXT-DOT3-MIB,SNMPv2-MIB,RMON MIB Groups1,2,3,9Switch PropertiesMAC Table Size16KMax.No.of VLANs256VLAN ID Range VID1to4094IGMP Groups1024Priority Queues8Packet Buffer Size12MbitsSerial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)USB InterfaceUSB Connector USB Type A(Reserved)Input/Output InterfaceDigital Input Channels1(On MGMT Module)Digital Inputs+13to+30V for state1-30to+3V for state0Max.input current:8mAAlarm Contact Channels3(On MGMT,PWR1,PWR2Module)Relay output with current carrying capacity of2A@30VDCPower ParametersInput Voltage with PWR-HV-P48installed:110/220VDC,110VAC,60HZ,220VAC,50Hz,PoE:48VDCwith PWR-LV-P48installed:24/48VDC,PoE:48VDCwith PWR-HV-NP installed:110/220VDC,110VAC,60HZ,220VAC,50Hzwith PWR-LV-NP installed:24/48VDCOperating Voltage with PWR-HV-P48installed:88to300VDC,90to264VAC,47to63Hz,PoE:46to57VDCwith PWR-LV-P48installed:18to72VDC(24/48VDC for hazardous location),PoE:46to57VDC(48VDC forhazardous location)with PWR-HV-NP installed:88to300VDC,90to264VAC,47to63Hzwith PWR-LV-NP installed:18to72VDCInput Current with PWR-HV-P48/PWR-HV-NP installed:Max.0.11A@110VDCMax.0.06A@220VDCMax.0.29A@110VACMax.0.18A@220VACwith PWR-LV-P48/PWR-LV-NP installed:Max.0.53A@24VDCMax.0.28A@48VDCMax.PoE Power Output per Port36WTotal PoE Power Budget Max.360W(with one power supply)for total PD consumption at48VDC input for PoEsystemsMax.360W(with one power supply)for total PD consumption at53to57VDC input forPoE+systemsMax.720W(with two power supplies)for total PD consumption at48VDC input for PoEsystemsMax.720W(with two power supplies)for total PD consumption at53to57VDC inputfor PoE+systemsOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsIP Rating IP40Dimensions176x115x163.25mm(6.93x4.53x6.44in)Weight2500g(5.51lb)Installation DIN-rail mounting,Wall mounting(with optional kit),Rack mounting(with optional kit) Environmental LimitsOperating Temperature Standard Temp Models:-10to60°C(-14to140°F)Wide Temp Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN62368-1,IEC62368-1,UL62368-1,IEC60950-1EMC EN55032/35,EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:8kV;Air:15kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:4kV;Signal:4kVIEC61000-4-5Surge:Power:4kV;Signal:4kVIEC61000-4-6CS:10VIEC61000-4-8PFMFIEC61000-4-11:Voltage Dips and Voltage InterruptionsRailway EN50121-4Traffic Control NEMA TS2Shock IEC60068-2-27Freefall IEC60068-2-31Vibration IEC60068-2-6Hazardous Locations Class I Division2,ATEXPower Substation IEEE1613,IEC61850-3MTBFTime1,007,790hrsStandards Telcordia SR332WarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x MDS-G4020-L3Series switchCable1x RJ45-to-DB9console cableInstallation Kit(Pre-installed)2x DIN-rail kit2x cap,plastic,for RJ45portDocumentation1x quick installation guide1x product notice,Simplified Chinese1x product certificates of quality inspection,Simplified Chinese1x warranty cardNote This product requires additional modules(sold separately)to function.DimensionsOrdering InformationModel Name Layer Total No.ofPorts100/1000BaseSFPSlots10/100/1000BaseT(X)Ports(RJ45Connector)PoE10/100/1000BaseT(X)Ports(RJ45Connector)10/100BaseT(X)Ports(RJ45Connector)PoE10/100BaseT(X)Ports(RJ45Connector)OperatingTemp.MDS-G4020-L3320Up to16Up to20Up to16Up to16Up to16-10to60°C MDS-G4020-L3-T320Up to16Up to20Up to16Up to16Up to16-40to75°C Accessories(sold separately)LM-7000H Module SeriesLM-7000H-4GTX Gigabit Ethernet module with410/100/1000BaseT(X)portsLM-7000H-4GPoE Gigabit Ethernet module with410/100/1000BaseT(X)IEEE802.3af/at PoE+portsLM-7000H-4GSFP Gigabit Ethernet module with4100/1000BaseSFP slotsLM-7000H-4TX Fast Ethernet module with410/100BaseT(X)portsLM-7000H-4PoE Fast Ethernet module with410/100BaseT(X)IEEE802.3af/at PoE+portsPower ModulesPWR-LV-P48Power supply module(24/48VDC)with system power input,relay,PoE power inputPWR-HV-P48Power supply module(110/220VAC/VDC)with system power input,relay,PoE power inputPWR-LV-NP Power supply module(24/48VDC)with system power input,relayPWR-HV-NP Power supply module(110/220VAC/VDC)with system power input,relayWall-Mounting KitsWK-112-01Wall-mounting kit,2plates,8screwsRack-Mounting KitsRK-3U-02Rack-mounting kit with4L-shaped plates for the MDS-G4000and MDS-G4000-4XGS SeriesSFP ModulesSFP-1FEMLC-T SFP module with1100Base multi-mode,LC connector for2/4km transmission,-40to85°C operatingtemperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300m/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300m/550m transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for1km/2km transmission,0to60°Coperating temperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for1km/2km transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GTXRJ45-T SFP module with11000BaseT port with RJ45connector for100m transmission,-40to75°C operatingtemperaturePower SuppliesHDR-60-2460W/2.5A DIN-rail24VDC power supply,universal85to264VAC or120to370VDC input voltage,-30to70°C operating temperatureNDR-120-24120W/5.0A DIN-rail24VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureNDR-120-48120W/2.5A DIN-rail48VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureNDR-240-48240W/5.0A DIN-rail48VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureSoftwareMXview-50MXview license for50nodesMXview-100MXview license for100nodesMXview-250MXview license for250nodesMXview-500MXview license for500nodesMXview-1000MXview license for1000nodesMXview-2000MXview license for2000nodesMXview Upgrade-50MXview license expansion for50nodes©Moxa Inc.All rights reserved.Updated Aug25,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
Moxa EDS-510A 系列7+3G端口高速 managed Ethernet 交换机说明书
EDS-510A Series7+3G-port Gigabit managed EthernetswitchesFeatures and Benefits•2Gigabit Ethernet ports for redundant ring and1Gigabit Ethernet port for uplink solution•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),1RSTP/ STP,and MSTP for network redundancy•TACACS+,SNMPv3,IEEE802.1X,HTTPS,and SSH to enhance network security•Easy network management by web browser,CLI,Telnet/serial console, Windows utility,and ABC-01CertificationsIntroductionThe EDS-510A Gigabit managed redundant Ethernet switches are equipped with up to3Gigabit Ethernet ports,making them ideal for building a Gigabit Turbo Ring,but leaving a spare Gigabit port for uplink use.The Ethernet redundancy technologies,Turbo Ring and Turbo Chain(recovery time<20ms),RSTP/STP,and MSTP,can increase system reliability and the availability of your network backbone.The EDS-510A Series is designed especially for communication demanding applications such as process control,shipbuilding,ITS,and DCS systems,which can benefit from a scalable backbone construction.Additional Features and Benefits•Command line interface(CLI)for quickly configuring majormanaged functions•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP and Modbus TCP protocols for devicemanagement and monitoring•IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•QoS(IEEE802.1p/1Q and TOS/DiffServ)to increase determinism•Port Trunking for optimum bandwidth utilization•SNMPv1/v2c/v3for different levels of network management•RMON for proactive and efficient network monitoring•Bandwidth management to prevent unpredictable network status•Lock port function for blocking unauthorized access based on MACaddress•Automatic warning by exception through email and relay outputSpecificationsInput/Output InterfaceAlarm Contact Channels2,Relay output with current carrying capacity of1A@24VDCDigital Input Channels2Digital Inputs+13to+30V for state1-30to+3V for state0Max.input current:8mAEthernet Interface10/100BaseT(X)Ports(RJ45connector)7Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection10/100/1000BaseT(X)Ports(RJ45connector)EDS-510A-1GT2SFP Series:1EDS-510A-3GT Series:31.Gigabit Ethernet recovery time<50msSupported functions:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection1000BaseSFP Slots EDS-510A-1GT2SFP Series:2EDS-510A-3SFP Series:3Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3ab for1000BaseT(X)IEEE802.3z for1000BaseSX/LX/LHX/ZXIEEE802.1X for authenticationIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingIEEE802.1p for Class of ServiceIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPEthernet Software FeaturesFilter802.1Q VLAN,Port-based VLAN,IGMP v1/v2,GVRP,GMRPIndustrial Protocols EtherNet/IP,Modbus TCPManagement IPv4/IPv6,SNMPv1/v2c/v3,LLDP,Port Mirror,Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Fiber check,Flow control,RARP,RMON,SMTP,SNMP Inform,Syslog,Telnet,TFTPMIB MIB-II,Bridge MIB,Ethernet-like MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols STP,MSTP,RSTP,LACP,Link Aggregation,Turbo Chain,Turbo Ring v1/v2 Security HTTPS/SSL,RADIUS,TACACS+,Port Lock,SSHTime Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups256MAC Table Size8KMax.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094LED InterfaceLED Indicators PWR1,PWR2,FAULT,10/100M(TP port),1000M(Gigabit port),MSTR/HEAD,CPLR/TAILSerial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Current EDS-510A-1GT2SFP Series:0.38A@24VDCEDS-510A-3GT Series:0.55A@24VDCEDS-510A-3SFP Series:0.39A@24VDCInput Voltage24VDC,Redundant dual inputsOperating Voltage12to45VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions80.2x135x105mm(3.16x5.31x4.13in)Weight1170g(2.58lb)Installation DIN-rail mounting,Wall mounting(with optional kit) Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN60950-1,UL60950-1,CSA C22.2No.60950-1,UL508 Hazardous Locations ATEX,Class I Division2EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFTraffic Control NEMA TS2Shock IEC60068-2-27Freefall IEC60068-2-31Vibration IEC60068-2-6MTBFTime204,901hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-510A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SC fiber port(-1GT2SFP models)2x cap,plastic,for ST fiber port(-3SFP models)Documentation1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified ChineseNote SFP modules need to be purchased separately for use with this product. DimensionsOrdering InformationModel Name 10/100BaseT(X)PortsRJ45Connector10/100/1000BaseT(X)PortsRJ45Connector1000Base SFP Slots Operating Temp.EDS-510A-3GT73–-10to60°C EDS-510A-3GT-T73–-40to75°C EDS-510A-3SFP7–3-10to60°C EDS-510A-3SFP-T7–3-40to75°C EDS-510A-1GT2SFP712-10to60°C EDS-510A-1GT2SFP-T712-40to75°CAccessories(sold separately)Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperatureSFP ModulesSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for500m transmission,0to60°C operatingtemperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for500m transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kitSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.All rights reserved.Updated Mar11,2020.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
莫克斯(Moxa) EDS-P510A系列8+2G端口PoE+管理以太网交换机说明书
EDS-P510A Series8+2G-port Gigabit PoE+managed Ethernet switches with8IEEE802.3af/at PoE+portsFeatures and Benefits•8built-in PoE+ports compliant with IEEE802.3af/at•Up to36W output per PoE+port•3kV LAN surge protection for extreme outdoor environments•PoE diagnostics for powered-device mode analysis•2Gigabit combo ports for high-bandwidth and long-distance communication •Operates with240watts full PoE+loading at-40to75°C•Supports MXstudio for easy,visualized industrial network management•V-ON™ensures millisecond-level multicast data and video network recoveryCertificationsIntroductionMoxa’s EDS-P510A Series has810/100BaseT(X),802.3af(PoE),and802.3at(PoE+)-compliant Ethernet ports,and2combo Gigabit Ethernet ports. The EDS-P510A-8PoE Ethernet switches provide up to30watts of power per PoE+port in standard mode and allow high-power output of up to36 watts for industrial heavy-duty PoE devices,such as weather-proof IP surveillance cameras with wipers/heaters,high-performance wireless access points,and IP phones.The EDS-P510A Ethernet Series is highly versatile,and the SFP fiber ports can transmit data up to120km from the device to the control center with high EMI immunity.The Ethernet switches support a variety of management functions,as well as STP/RSTP,Turbo Ring,Turbo Chain,PoE power management,PoE device auto-checking,PoE power scheduling,PoE diagnostic,IGMP,VLAN,QoS,RMON,bandwidth management,and port mirroring.The EDS-P510A Series is designed with3kV surge protection for harsh outdoor applications to increase the reliability of PoE systems.Additional Features and Benefits•Supports different PoE output settings(High-power36W,Forceand Legacy modes)to maximize powered device compatibility•Supports Smart PoE functions(PoE diagnosis,PD failure check,PoE scheduling,PoE Event Warning)to enhance PoE operationalefficiency•Command line interface(CLI)for quickly configuring majormanaged functions•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP and Modbus TCP protocols for devicemanagement and monitoring•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),1RSTP/STP,and MSTP for network redundancy•Compatible with PROFINET protocol for transparent datatransmission•IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•QoS(IEEE802.1p/1Q and TOS/DiffServ)to increase determinism•Port Trunking for optimum bandwidth utilization•TACACS+,IEEE802.1X,SNMPv3,HTTPS,and SSH to enhancenetwork security•Lock port function for blocking unauthorized access based on MACaddress•SNMPv1/v2c/v3for different levels of network management•RMON for proactive and efficient network monitoring•Bandwidth management to prevent unpredictable network status•Port mirroring for online debugging•Automatic warning by exception through email and relay output1.Gigabit Ethernet recovery time<50msSpecifications Ethernet InterfaceCombo Ports(10/100/1000BaseT(X)or100/ 1000BaseSFP+)2Full/Half duplex modeAuto MDI/MDI-X connection Auto negotiation speedPoE Ports(10/100BaseT(X),RJ45connector)8Full/Half duplex modeAuto MDI/MDI-X connectionAuto negotiation speedStandards IEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1X for authenticationIEEE802.3for10BaseTIEEE802.3ab for1000BaseT(X)IEEE802.3ad for Port Trunk with LACPIEEE802.3af/at for PoE/PoE+outputIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.3z for1000BaseSX/LX/LHX/ZXEthernet Software FeaturesFilter GMRP,GVRP,IGMP v1/v2,Port-based VLANIndustrial Protocols EtherNet/IP,Modbus TCPManagement Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Fiber check,Flow control,IPv4/IPv6,LLDP,Port Mirror,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTPMIB Bridge MIB,Ethernet-like MIB,MIB-II,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols LACP,Link Aggregation,MSTP,RSTP,STP,Turbo Chain,Turbo Ring v1/v2 Security HTTPS/SSL,Port Lock,RADIUS,TACACS+,SSHTime Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups1024MAC Table Size8KMax.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094Serial InterfaceConsole Port RS-232(TxD,RxD,GND),10-pin RJ45(19200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReserveInput/Output InterfaceAlarm Contact Channels1,Relay output with current carrying capacity of0.5A@48VDC Digital Input Channels1Digital Inputs Max.input current:8mA+13to+30V for state1-30to+3V for state0Power ParametersInput Voltage48VDC,Redundant dual inputsOperating Voltage44to57VDCInput Current 5.36A@48VDCPower Consumption(Max.)Max.17.28W full loading without PDs’consumptionPower Budget Max.240W for total PD consumptionMax.36W for each PoE portConnection2removable2-contact terminal block(s)Overload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions79.2x135x105mm(3.12x5.31x4.13in)Weight1030g(2.28lb)Installation DIN-rail mounting,Wall mounting(with optional kit) Environmental LimitsOperating Temperature EDS-P510A-8PoE-2GTXSFP:-10to60°C(14to140°F)EDS-P510A-8PoE-2GTXSFP-T:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety UL508EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations Class I Division2Railway EN50121-4Traffic Control NEMA TS2Freefall IEC60068-2-31Shock IEC60068-2-27Vibration IEC60068-2-6MTBFTime708,972hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-P510A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SFP slotDocumentation1x quick installation guide1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x warranty cardNote SFP modules need to be purchased separately for use with this product. DimensionsOrdering InformationModel NameCombo Ports10/100/1000BaseT(X)or100/1000BaseSFP+PoE Ports10/100BaseT(X),RJ45ConnectorOperating Temp.EDS-P510A-8PoE-2GTXSFP28-10to60°C EDS-P510A-8PoE-2GTXSFP-T28-40to75°CAccessories(sold separately)SoftwareMXview Industrial network management software designed for converged automation networksStorage KitsABC-02-USB Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,0to60°C operating temperatureABC-02-USB-T Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,-40to75°C operating temperatureSFP ModulesSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1FEMLC-T SFP module with1100Base multi-mode with LC connector for4km transmission,-40to85°Coperating temperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for500m transmission,0to60°C operatingtemperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for500m transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperaturePower SuppliesDR-120-48120W/2.5A DIN-rail48VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-75-4875W/1.6A DIN-rail48VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureDRP-240-48DIN-rail48VDC power supply with240W/5A,85to264VAC,or120to370VDC input,-10to70°Coperating temperatureSDR-480P-48DIN-rail48VDC power supply with480W/10A,90to264VAC,or127to370VDC input,(current sharingup to3840W),-25to70°C operating temperatureWall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Nov12,2018.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
Moxa EDS-G512E Series 12G-port Gigabit 交换机用户手册说明书
EDS-G512E Series12G-port(with8PoE+ports option)full Gigabit managed EthernetswitchesFeatures and Benefits•8IEEE802.3af and IEEE802.3at PoE+standard ports•36-watt output per PoE+port in high-power mode•Turbo Ring and Turbo Chain(recovery time<50ms@250switches),RSTP/ STP,and MSTP for network redundancy•RADIUS,TACACS+,MAB Authentication,SNMPv3,IEEE802.1X,MAC ACL, HTTPS,SSH,and sticky MAC-addresses to enhance network security •Security features based on IEC62443•EtherNet/IP,PROFINET,and Modbus TCP protocols supported for device management and monitoring•Supports MXstudio for easy,visualized industrial network management•V-ON™ensures millisecond-level multicast data and video network recoveryCertificationsIntroductionThe EDS-G512E Series is equipped with12Gigabit Ethernet ports and up to4fiber-optic ports,making it ideal for upgrading an existing network to Gigabit speed or building a new full Gigabit backbone.It also comes with810/100/1000BaseT(X),802.3af(PoE),and802.3at(PoE+)-compliant Ethernet port options to connect high-bandwidth PoE devices.Gigabit transmission increases bandwidth for higher performance and transfers large amounts of triple-play services across a network quickly.Redundant Ethernet technologies such as Turbo Ring,Turbo Chain,RSTP/STP,and MSTP increase the reliability of your system and improve the availability of your network backbone.The EDS-G512E Series is designed specifically for communication demanding applications,such as video and process monitoring,ITS,and DCS systems,all of which can benefit from a scalable backbone construction.Additional Features and Benefits•Command line interface(CLI)for quickly configuring majormanaged functions•Advanced PoE management function(PoE port setting,PD failurecheck,and PoE scheduling)•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP,PROFINET,and Modbus TCP protocols fordevice management and monitoring•IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•Supports the ABC-02-USB(Automatic Backup Configurator)forsystem configuration backup/restore and firmware upgrade•Port mirroring for online debugging•QoS(IEEE802.1p/1Q and TOS/DiffServ)to increase determinism•Port Trunking for optimum bandwidth utilization•RADIUS,TACACS+,MAB Authentication,SNMPv3,IEEE802.1X,MACACL,HTTPS,SSH,and sticky MAC address to enhance networksecurity•SNMPv1/v2c/v3for different levels of network management•RMON for proactive and efficient network monitoring•Bandwidth management to prevent unpredictable network status•Lock port function for blocking unauthorized access based on MACaddress•Automatic warning by exception through email and relay outputSpecificationsInput/Output InterfaceAlarm Contact Channels1,Relay output with current carrying capacity of1A@24VDCButtons Reset buttonDigital Input Channels1Digital Inputs+13to+30V for state1-30to+3V for state0Max.input current:8mAEthernet Interface10/100/1000BaseT(X)Ports(RJ45connector)EDS-G512E-4GSFP:8Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connectionEDS-G512E-4GSFP-T:8Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connectionPoE Ports(10/100/1000BaseT(X),RJ45connector)EDS-G512E-8PoE-4GSFP:8EDS-G512E-8PoE-4GSFP-T:8100/1000BaseSFP Slots4Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3ab for1000BaseT(X)IEEE802.3z for1000BaseSX/LX/LHX/ZXIEEE802.3x for flow controlIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1X for authenticationIEEE802.3ad for Port Trunk with LACPEthernet Software FeaturesFilter802.1Q VLAN,Port-based VLAN,GVRP,IGMP v1/v2/v3,GMRPIndustrial Protocols EtherNet/IP,Modbus TCP,PROFINET IO DeviceManagement LLDP,Back Pressure Flow Control,BOOTP,Port Mirror,DHCP Option66/67/82,DHCPServer/Client,Fiber check,Flow control,IPv4/IPv6,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTPMIB Ethernet-like MIB,MIB-II,Bridge MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols Link Aggregation,MSTP,RSTP,STP,Turbo Chain,Turbo Ring v1/v2Security Broadcast storm protection,HTTPS/SSL,TACACS+,SNMPv3,MAB authentication,Sticky MAC,NTP authentication,MAC ACL,Port Lock,RADIUS,SSH,SMTP with TLS Time Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups2048Jumbo Frame Size9.6KBMAC Table Size8KMax.No.of VLANs256Packet Buffer Size4MbitsPriority Queues4VLAN ID Range VID1to4094USB InterfaceStorage Port USB Type ALED InterfaceLED Indicators PWR1,PWR2,STATE,FAULT,10/100M(TP port),1000M(TP port),100/1000M(SFPport),MSTR/HEAD,CPLR/TAIL,smart PoE LED(EDS-G512E-8PoE-4GSFP Series only) Serial InterfaceConsole Port USB-serial console(Type B connector)DIP Switch ConfigurationDIP Switches Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable4-contact terminal block(s)Input Current EDS-G512E-4GSFP models:0.34A@24VDCEDS-G512E-8PoE-4GSFP models:5.30A@48VDCInput Voltage EDS-G512E-4GSFP models:12/24/48/-48VDCEDS-G512E-8PoE-4GSFP models:48VDC,Redundant dual inputsOperating Voltage EDS-G512E-4GSFP models:9.6to60VDCEDS-G512E-8PoE-4GSFP models:44to57VDC(>50VDC for PoE+outputrecommended)Overload Current Protection SupportedReverse Polarity Protection SupportedPower Budget EDS-G512E-8PoE-4GSFP:Max.240W for total PD consumptionEDS-G512E-8PoE-4GSFP:Max.36W for each PoE portPower Consumption(Max.)EDS-G512E-8PoE-4GSFP:Max.14.36W full loading without PDs’consumptionEDS-G512E-8PoE-4GSFP-T:Max.14.36W full loading without PDs’consumptionEDS-G512E-8PoE-4GSFP:When selecting a power supply,check the PD powerconsumption.EDS-G512E-8PoE-4GSFP-T:When selecting a power supply,check the PD powerconsumption.Physical CharacteristicsHousing MetalIP Rating IP30Dimensions79.2x135x137mm(3.1x5.3x5.4in)Weight EDS-G512E-4GSFP:1,440g(3.18lb)EDS-G512E-8PoE-4GSFP:1,540g(3.40lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EDS-G512E-4GSFP/EDS-G512E-8PoE-4GSFP models:UL508EDS-G512E-8PoE-4GSFP models:EN60950-1(LVD)EMC EN61000-6-2/-6-4EMS EDS-G512E-4GSFP:IEC61000-4-2ESD:Contact:8kV;Air:15kVEDS-G512E-4GSFP:IEC61000-4-3RS:80MHz to1GHz:10V/mEDS-G512E-8PoE-4GSFP:IEC61000-4-3RS:80MHz to1GHz:20V/mEDS-G512E-4GSFP-T:IEC61000-4-3RS:80MHz to1GHz:10V/mEDS-G512E-8PoE-4GSFP-T:IEC61000-4-3RS:80MHz to1GHz:20V/mEDS-G512E-4GSFP:IEC61000-4-4EFT:Power:4kV;Signal:4kVEDS-G512E-8PoE-4GSFP:IEC61000-4-4EFT:Power:2kV;Signal:2kVEDS-G512E-8PoE-4GSFP-T:IEC61000-4-4EFT:Power:2kV;Signal:2kVEDS-G512E-4GSFP-T:IEC61000-4-4EFT:Power:4kV;Signal:4kVEDS-G512E-4GSFP:IEC61000-4-5Surge:Power:4kV;Signal:4kVEDS-G512E-8PoE-4GSFP:IEC61000-4-5Surge:Power:2kV;Signal:4kVEDS-G512E-4GSFP:IEC61000-4-5Surge:Power:4kV;Signal:4kVEDS-G512E-4GSFP-T:IEC61000-4-5Surge:Power:4kV;Signal:4kVEDS-G512E-8PoE-4GSFP:IEC61000-4-5Surge:Power:2kV;Signal:2kVEDS-G512E-8PoE-4GSFP-T:IEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFEMI FCC Part15B Class AHazardous Locations EDS-G512E-4GSFP Series:ATEX,Class I Division2Maritime EDS-G512E-4GSFP models:DNV,LR,ABS,NKPower Substation IEC61850-3,IEEE1613Railway EN50121-4Traffic Control EDS-G512E-4GSFP:NEMA TS2Shock IEC60068-2-27Freefall IEC60068-2-32Vibration IEC60068-2-6MTBFTime EDS-G512E-4GSFP(-T)models:816,823hrsEDS-G512E-8PoE-4GSFP(-T)models:788,215hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-G512E Series switchCable1x USB type A male to USB type B maleInstallation Kit4x cap,plastic,for RJ45portDocumentation1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified ChineseNote SFP modules need to be purchased separately for use with this product.DimensionsOrdering InformationModel Name10/100/1000BaseT(X)Ports,RJ45ConnectorPoE Ports,10/100/1000BaseT(X),RJ45ConnectorIEEE802.3af/at forPoE/PoE+Output100/1000Base SFPSlotsOperating Temp.EDS-G512E-4GSFP8––4-10to60°C EDS-G512E-4GSFP-T8––4-40to75°C EDS-G512E-8PoE-4GSFP–8✓4-10to60°C EDS-G512E-8PoE-4GSFP-T–8✓4-40to75°C Accessories(sold separately)Storage KitsABC-02-USB Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,0to60°C operating temperatureABC-02-USB-T Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,-40to75°C operating temperatureRack-Mounting KitsRK-4U19-inch rack-mounting kitWall-Mounting KitsWK-51-01Wall mounting kit with2plates(51.6x67x2mm)and6screwsSFP ModulesSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1FEMLC-T SFP module with1100Base multi-mode,LC connector for2/4km transmission,-40to85°C operatingtemperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for1km/2km transmission,0to60°Coperating temperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for1km/2km transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300m/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300m/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperatureSFP-1GTXRJ45-T SFP module with11000BaseT port with RJ45connector for100m transmission,-40to75°C operatingtemperatureSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.All rights reserved.Updated June16,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA交换机设置指导
Moxa交换机特点
01
高可靠性
Moxa交换机采用工业级设计， 具有防震、防尘、防潮等特点， 能够在恶劣的环境下稳定运行。
实时性
02
03
易管理性
Moxa交换机支持实时传输技术， 能够满足工业自动化等领域的实 时性要求。
解决方案
检查交换机的IP地址配置是否正确，确认连接线缆是否正常，核对登录凭证（用户名和 密码）是否正确。如果问题依然存在，可能需要重置交换机或联系技术支持。
VLAN配置错误
总结词
交换机上配置的VLAN不正确，导致无法实现正确的网络隔 离。
详细描述
可能是在配置VLAN时，将端口错误地划分到了不同的 VLAN，或者VLAN的名称和IP地址配置不正确。
Moxa交换机提供Web界面和命 令行接口，方便用户进行配置和 管理。
Moxa交换机应用场景
01
02
03
04
工业自动化
Moxa交换机可用于工厂自动 化生产线、智能制造等领域， 实现设备间的数据传输和控制
。
轨道交通
Moxa交换机可用于地铁、轻 轨等轨道交通系统，实现车辆
控制、信号传输等功能。
智能交通
VS
配置管理
Moxa交换机支持通过Web界面或命令行 进行配置管理。用户可以根据实际需求， 对交换机的各项参数进行设置，如VLAN 划分、端口配置、IP地址分配等。
固件升级与备份
固件升级
随着技术的不断更新，Moxa交换机也需要不断升级固件以支持新的功能和修复已知的 漏洞。用户可以通过Moxa官方网站下载最新的固件版本，并按照说明进行升级操作。
MOXA交换机使用说明
MOXA交换机使用说明1、IP地址得设置通过IE工具来Ping 交换机默认得IP(出厂默认192、168、127、253)地址,进入交换机配置界面后,直接点击确认后,进入交换机设置界面对话框,IP地址设置请选择\Main Meun\Basic Settings\Network,出现下列对话框在此对话框下,设置人员在Switch IP Address 与 Switch Subnet Mask 旁得空白处填写预定得IP地址(如:192、168、12、20),以及相应得子网掩码地址(如:255、255、255、0);其她得如Auto IP Configuration 设置为Disable方式,不要选择HDCP方式。
2、主站(Master)设置完成了IP方式得设置后,就需要对交换得通讯协议与交换机进行相应得设置,选择\Main Menu\munication Redundancy(通讯冗余设置),进入对话框:在此对话框内,我们需要注意得就是Settings标记下方得设置参量,而Current Status 为相应得设置参量后交换机系统检测后得状态指示。
Redundancy Protocol (通讯协议设置):设置选择为Turbo Ring ,而非就是IEEE802协议(快速生成树)方式;采用Turbo Ring方式得情况下,需要在网络交换机组中设置一个Master(主站),选择主站得方式就是将Set as Master前得小方框内给予选中, 只需要选择确定后,点击Activate按钮即可生效。
(注意:在多个交换机组成网中只能有1个设置为Master,不可以多选;同时如果不对交换机进行Master设置,系统会自动设置交换机组中得1台为Master)。
Enable Ring Coupling (环间耦合端口定义)在实际得项目运用中不常运用到,在此不给予更多得描述。
需要提醒得就是工程人员在设置过程中不要将Enable Ring Coupling 前得小方格选中,同时要注意得就是对应得Coupling Port与 Coupling Control Port后得端口与前面得Redundant Ports 1st Port与 2nd Port(冗余连接端口定义)设置得端口重复。
莫桑（Moxa）PT-7528系列IEC 61850-328口层2Managed交换机说明说明书
PT-7528SeriesIEC61850-328-port Layer2managed rackmount EthernetswitchesFeatures and Benefits•IEC61850-3,IEEE1613(power substations)compliant•Built-in MMS server based on IEC61850-90-4switch data modeling forpower SCADA•Noise Guard™wire speed zero packet loss technology•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),1RSTP/STP,and MSTP for network redundancy•Isolated redundant power inputs with universal24VDC,48VDC,or110/220VDC/VAC power supply range•-40to85°C operating temperature rangeCertificationsIntroductionThe PT-7528Series is designed for power substation automation applications that operate in extremely harsh environments.The PT-7528Series supports Moxa’s Noise Guard technology,is compliant with IEC61850-3,and its EMC immunity exceeds IEEE1613Class2standards to ensure zero packet loss while transmitting at wire speed.The PT-7528Series also features critical packet prioritization(GOOSE and SMVs),a built-in MMS server,and a configuration wizard designed specifically for substation automation.With Gigabit Ethernet,redundant ring,and110/220VDC/VAC isolated redundant power supplies,the PT-7528Series further increases the reliability of your communications and saves cabling/wiring costs.The wide range of PT-7528models available support multiple types of port configuration, with up to28copper or24fiber ports,and up to4Gigabit ports.Taken together,these features allow greater flexibility,making the PT-7528Series suitable for a variety of industrial applications.Additional Features and Benefits•Switch data modeling based on the IEC61850-90-4standard •Fiber Check™provides monitoring and diagnosis functions on MST/MSC/SSC/SFP fiber ports•VLAN Unaware:Supports priority-tagged frames to be received by specific IEDs•EtherNet/IP and Modbus TCP industrial Ethernet protocols supported•Configurable by web browser,Telnet/Serial console,CLI,Windows utility,and ABC-02automatic backup configurator•Turbo Ring and Turbo Chain(recovery time<20ms@250 switches),1RSTP/STP,and MSTP for network redundancy •DHCP Option82for IP address assignment with different policies •IGMP snooping and GMRP for filtering multicast traffic from industrial Ethernet protocols•IEEE802.3ad,LACP for optimum bandwidth utilization•Bandwidth management to prevent unpredictable network status •Multiport mirroring for online debugging•Automatic warning by exception through email and relay output •RMON for proactive and efficient network monitoring•Automatic recovery of connected device’s IP addresses•Line-swap fast recovery•Noise Guard™provides a high level of EMC immunity for critical applications,exceeding IEEE1613Class2Cybersecurity Features•User passwords with multiple levels of security protect against unauthorized configuration•SSH/HTTPS is used to encrypt passwords and data•Lock switch ports with802.1X port-based network access control so that only authorized clients can access the port•RADIUS/TACACS+allows you to manage passwords from a central location •802.1Q VLAN allows you to logically partition traffic transmitted between selected switch ports•Secure switch ports so that only specific devices and/or MAC addresses can access the ports•Disable one or more ports to block network traffic•SNMPv3provides encrypted authentication and access security1.Gigabit Ethernet recovery time<50msSpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)PT-7528-4TX Series:4PT-7528-8TX Series:8PT-7528-12TX Series:12PT-7528-16TX Series:16PT-7528-24TX Series:241000BaseSFP Slots PT-7528-4GSFP Series:4100BaseFX Ports(multi-mode SC connector)PT-7528-8MSC Series:8PT-7528-12MSC Series:12PT-7528-16MSC Series:16PT-7528-20MSC Series:20100BaseFX Ports(multi-mode ST connector)PT-7528-8MST Series:8PT-7528-12MST Series:12PT-7528-16MST Series:16PT-7528-20MST Series:20100BaseFX Ports(single-mode SC connector)PT-7528-8SSC Series:8Optical Fiber800Typical Distance4km5km40km80kmWave-length Typical(nm)130013101550TX Range(nm)1260to13601280to13401530to1570 RX Range(nm)1100to16001100to16001100to1600Optical Power TX Range(dBm)-14to-20*0to-50to-5 RX Range(dBm)-3to-32-3to-34-3to-34 Link Budget(dB)122929 Dispersion Penalty(dB)311*This range only applies to the PT-7528multi-mode SC and ST fiber modules.Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Cabling Direction Front cablingCompatible Modules PT-7528-24TX Series:Slot1:PM-7500-2GTXSP,PM-7500-4GTXSFP,PM-7500-2MSC/4MSC,PM-7500-2MST/4MST,PM-7500-2SSC/4SSCStandards IEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1X for authenticationIEEE802.3for10BaseTIEEE802.3ab for1000BaseT(X)IEEE802.3ad for Port Trunk with LACPIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.3z for1000BaseSX/LX/LHX/ZXEthernet Software FeaturesFilter802.1Q,GMRP,GVRP,IGMP v1/v2c,Port-based VLAN,VLAN unawareIndustrial Protocols EtherNet/IP,Modbus TCPManagement Back Pressure Flow Control,BOOTP,DHCP Option66/67/82,DHCP Server/Client,Flowcontrol,HTTP,IPv4/IPv6,LLDP,Port Mirror,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTP,Fiber checkMIB Bridge MIB,Ethernet-like MIB,MIB-II,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBPower Substation IEC61850QoS,MMS,Configuration WizardRedundancy Protocols Link Aggregation,MSTP,RSTP,STP,Turbo Chain,Turbo Ring v1/v2Security Broadcast storm protection,HTTPS/SSL,TACACS+,Port Lock,RADIUS,Rate Limit,SSHTime Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups256Jumbo Frame Size9.6KBMax.No.of VLANs256VLAN ID Range VID1to4094Priority Queues4Switching Capacity12.8GbpsForwarding Capacity12.8GbpsUSB InterfaceStorage Port USB Type ASerial InterfaceConsole Port USB-serial console(Type B connector)Input/Output InterfaceAlarm Contact Channels Resistive load:3A@30VDC,240VACPower ParametersConnection10-pin terminal blockInput Voltage PT-7528-HV-HV/WV-WV/WV-HV Series:Redundant power modulesPT-7528-WV Series:24/48VDC(18to72VDC)PT-7528-HV Series:110/220VAC/VDC(85to264VAC,88to300VDC)Input Current For models with fewer than8fiber ports:PT-7528-WV Series:0.741A@24VDC,0.364A@48VDCPT-7528-HV Series:0.147/0.077A@110/220VDC,0.283/0.190A@110/220VACFor models with8or more fiber ports:PT-7528-WV Series:1.428A@24VDC,0.735A@48VDCPT-7528-HV Series:0.586/0.382A@110/220VAC,0.313/0.167A@110/220VDC Overload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing AluminumIP Rating IP40Dimensions(without ears)440x44x325mm(17.32x1.73x12.80in)Weight4900g(10.89lb)Installation19-inch rack mountingEnvironmental LimitsOperating Temperature-40to85°C(-40to185°F)Note:Cold start requires minimum of100VAC@-40°CStorage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety UL508EMI EN55032Class A,CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:8kV;Air:15kVIEC61000-4-3RS:80MHz to1GHz:35V/mIEC61000-4-4EFT:Power:4kV;Signal:4kVIEC61000-4-5Surge:Power:4kV;Signal:4kVIEC61000-4-6CS:10VIEC61000-4-8PFMFIEC61000-4-11DIPsPower Substation IEC61850-3,IEEE1613Class2,Note:Models with MCS and SSC fiber ports arecompliant with IEEE1613Class1Railway EN50121-4Traffic Control NEMA TS2MTBFTime771,320hrsStandards Telcordia SR332WarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x PT-7528Series switchCable1x USB type A male to USB type B maleInstallation Kit4x cap,plastic,for RJ45port4x cap,plastic,for SFP slot2x rack-mounting earDocumentation1x document and software CD1x quick installation guide1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x warranty cardNote SFP modules and/or modules from the PM-7500Module Series need to be purchasedseparately for use with this product.DimensionsOrdering InformationModel Name 1000Base SFPSlots10/100BaseT(X)100BaseFX Input Voltage1Input Voltage2RedundantPower ModuleOperating Temp.PT-7528-24TX-WV-HV –24–24/48VDC110/220VDC/VAC✓-45to85°CPT-7528-24TX-WV–24–24/48VDC––-45to85°CPT-7528-24TX-HV–24–110/220VDC/VAC––-45to85°CPT-7528-24TX-WV-WV–24–24/48VDC24/48VDC✓-45to85°CPT-7528-24TX-HV-HV –24–110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-8MSC-16TX-4GSFP-WV 4168x multi-mode,SC connector24/48VDC––-45to85°CPT-7528-8MSC-16TX-4GSFP-WV-WV 4168x multi-mode,SC connector24/48VDC24/48VDC✓-45to85°CPT-7528-8MSC-16TX-4GSFP-HV 4168x multi-mode,SC connector110/220VDC/VAC––-45to85°CPT-7528-12MSC-12TX-4GSFP-WV 41212x multi-mode,SC connector24/48VDC––-45to85°CPT-7528-12MSC-12TX-4GSFP-WV-WV 41212x multi-mode,SC connector24/48VDC24/48VDC✓-45to85°CPT-7528-12MSC-12TX-4GSFP-HV 41212x multi-mode,SC connector110/220VDC/VAC––-45to85°CPT-7528-12MSC-12TX-4GSFP-HV-HV 41212x multi-mode,SC connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-16MSC-8TX-4GSFP-WV 4816x multi-mode,SC connector24/48VDC––-45to85°CPT-7528-16MSC-8TX-4GSFP-WV-WV 4816x multi-mode,SC connector24/48VDC24/48VDC✓-45to85°CPT-7528-16MSC-8TX-4GSFP-HV 4816x multi-mode,SC connector110/220VDC/VAC––-45to85°CPT-7528-16MSC-8TX-4GSFP-HV-HV 4816x multi-mode,SC connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-20MSC-4TX-4GSFP-WV 4420x multi-mode,SC connector24/48VDC––-45to85°CPT-7528-20MSC-4TX-4GSFP-WV-WV 4420x multi-mode,SC connector24/48VDC24/48VDC✓-45to85°CPT-7528-20MSC-4TX-4GSFP-HV 4420x multi-mode,SC connector110/220VDC/VAC––-45to85°CPT-7528-20MSC-4TX-4GSFP-HV-HV 4420x multi-mode,SC connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-8SSC-16TX-4GSFP-WV-WV 4168x single-mode,SC connector24/48VDC24/48VDC✓-45to85°CPT-7528-8SSC-16TX-4GSFP-HV-HV 4168x single-mode,SC connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-8MST-16TX-4GSFP-WV 4168x multi-mode,ST connector24/48VDC––-45to85°CPT-7528-8MST-16TX-4GSFP-WV-WV 4168x multi-mode,ST connector24/48VDC24/48VDC✓-45to85°CPT-7528-8MST-16TX-4GSFP-HV 4168x multi-mode,ST connector110/220VDC/VAC––-45to85°CPT-7528-8MST-16TX-4GSFP-HV-HV 4168x multi-mode,ST connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-12MST-12TX-4GSFP-WV 41212x multi-mode,ST connector24/48VDC––-45to85°CPT-7528-12MST-12TX-4GSFP-WV-WV 41212x multi-mode,ST connector24/48VDC24/48VDC✓-45to85°CPT-7528-12MST-12TX-4GSFP-HV 41212x multi-mode,ST connector110/220VDC/VAC––-45to85°CPT-7528-12MST-12TX-4GSFP-HV-HV 41212x multi-mode,ST connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CPT-7528-16MST-8TX-4GSFP-WV 4816x multi-mode,ST connector24/48VDC––-45to85°CPT-7528-16MST-8TX-4GSFP-WV-WV 4816x multi-mode,ST connector24/48VDC24/48VDC✓-45to85°CPT-7528-16MST-8TX-4GSFP-HV 4816x multi-mode,ST connector110/220VDC/VAC––-45to85°CPT-7528-20MST-4TX-4GSFP-WV 4420x multi-mode,ST connector24/48VDC––-45to85°CPT-7528-20MST-4TX-4GSFP-WV-WV 4420x multi-mode,ST connector24/48VDC24/48VDC✓-45to85°CPT-7528-20MST-4TX-4GSFP-HV 4420x multi-mode,ST connector110/220VDC/VAC––-45to85°CPT-7528-20MST-4TX-4GSFP-HV-HV 4420x multi-mode,ST connector110/220VDC/VAC110/220VDC/VAC✓-45to85°CAccessories(sold separately)PM-7500Module SeriesPM-7500-2GTXSFP Gigabit Ethernet module with2100/1000BaseSFP slots or2100/1000BaseT(X)pliant withIEC61850-3.-40to85°C operating temperaturePM-7500-2MSC Fast Ethernet module with2100BaseFX multi-mode ports with SC pliant with IEC61850-3.-40to85°C operating temperaturePM-7500-2MST Fast Ethernet module with2100BaseFX multi-mode ports with ST pliant with IEC61850-3.-40to85°C operating temperaturePM-7500-2SSC Fast Ethernet module with2100BaseFX single-mode ports with SC pliant with IEC61850-3.-40to85°C operating temperaturePM-7500-4GTXSFP Gigabit Ethernet module with4100/1000BaseSFP slots or4100/1000BaseT(X)pliant withIEC61850-3.-40to85°C operating temperaturePM-7500-4MSC Fast Ethernet module with4100BaseFX multi-mode ports with SC pliant with IEC61850-3.-40to85°C operating temperaturePM-7500-4MST Fast Ethernet module with4100BaseFX multi-mode ports with ST pliant with IEC61850-3.-40to85°C operating temperaturePM-7500-4SSC Fast Ethernet module with4100BaseFX single-mode ports with SC pliant with IEC61850-3.-40to85°C operating temperatureStorage KitsABC-02-USB-T Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,-40to75°C operating temperatureSFP ModulesSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for500m transmission,0to60°C operatingtemperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for500m transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperatureSFP-1GTXRJ45-T SFP module with11000BaseT port with RJ45connector for100m transmission,-40to75°C operatingtemperatureSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.All rights reserved.Updated Mar18,2020.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA ToughNet TN-4500A Series 轨道交通应用Ethernet交换机说明书
TN-4500A SeriesEN5015512+4G/24+4G-port Gigabit Ethernet switches with up to20PoEportsFeatures and Benefits•2to4Gigabit ports with bypass relay function on the bypass models•2Gigabit fiber ports with embedded multi-mode Q-ODC®interface on fibermodels•Up to4Gigabit ports with PoE function•Up to20IEEE802.3at/af compliant combo PoE and Ethernet ports•Supports regular and push-pull M12connectors•Turbo Ring and Turbo Chain(recovery time<20ms@250switches)1,andSTP/RSTP/MSTP for network redundancy•Complies with all EN50155mandatory test items2•Isolated power with24to110VDC power supply range•-40to70°C system operating temperature rangeCertificationsIntroductionThe ToughNet TN-4500A Series M12managed Ethernet switches are designed for railway applications,including rolling stock and wayside installations.The switches use M12and other circular connectors to ensure tight,robust connections,and guarantee reliable operation in industrial environments where vibration and shock are commonplace.The TN-4500A Series Ethernet switches provide12or24fast Ethernet M12ports with or without IEEE802.3at/af compliant PoE functionality,and the Gigabit models have4Gigabit Ethernet interfaces with PoE and optional bypass relay functionality.In addition,the fiber models provide2Gigabit fiber interface ports with an embedded2km multimode fiber transceiver.The PoE switches are classified as power source equipment(PSE).The switches provide up to30watts of power per port,and can be used to power IEEE802.3at/af compliant powered devices(PDs),such as IP cameras,wireless access points,and IP phones.The24to110VDC wide power input range and isolated dual power inputs not only allow you to use the same type of power source at different sites around the globe,but also increase the reliability of your communications system. Furthermore,the-40to70°C operating temperature range of the switches ensures they can withstand deployment in harsh environments.TN-4500A Series Ethernet switches are compliant with the mandatory sections of EN50155,covering operating temperature,power input voltage, surge,ESD,and vibration,as well as conformal coating and power insulation,making the switches suitable for a variety of industrial applications. Additional Features and Benefits•Provides up to30watts per PoE port with a total power budget of 120watts per switch•DHCP Option82for IP address assignment with different policies •IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease network planning•QoS(IEEE802.1p/1Q and ToS/DiffServ)allows real-time traffic classification and prioritization•IEEE802.3ad,LACP for optimum bandwidth utilization •SNMPv1/v2c/v3for different levels of network management •TACACS+,SNMPv3,IEEE802.1X,HTTPS,and SSH to enhance network security •RMON for proactive and efficient network monitoring •Bandwidth management to prevent unpredictable network status •Lock port allows access by only authorized MAC addresses •Port mirroring for online debugging•Automatic warning by exception through email and relay output •Line-swap fast recovery•LLDP for automatic topology discovery in network management software•Configurable by web browser,Telnet/serial console,CLI,and Windows utility•Loop protection to prevent network loops•Wall mounting installation capability1.If the port link speed is1Gigabit or higher,the recovery time is<50ms.2.This product is suitable for rolling stock railway applications,as defined by the EN50155standard.For a more detailed statement,click here:/doc/specs/EN_50155_Compliance.pdfSpecificationsInput/Output InterfaceAlarm Contact Channels2x relay output in one M12A-coded5-pin male connector with current carryingcapacity of1A@30VDCEthernet Interface10/100/1000BaseT(X)Ports(M12X-coded8-pin female connector)TN-4516A-4GTX-WV-T models:4 TN-4516A-4GTX-WV-CT-T models:410/100BaseT(X)Ports(M12D-coded4-pin female connector)TN-4512A models:12TN-4516A non-PoE models:16 TN-4516A-4GTX models:12 TN-4516A-4GTXBP models:12 TN-4524A/4528A models:8PoE Ports(10/100BaseT(X),M12D-coded4-pin female connector)TN-4516A PoE models:12TN-4520A/4524A/4528A models:16PoE Ports(100/1000BaseT(X),M12X-coded8-pin female connector)TN-4500A PoE models:4TN-4500A PoE fiber(ODC)and bypass(GTXBP)models:210/100/1000BaseT(X)Ports(M12X-coded8-pin female connector with bypass relay)TN-4516A-4GTXBP models:4TN-4516A-12PoE-2GPoE-2GTXBP models:2 TN-4528A-16PoE-2GPoE-2GTXBP models:210/100/1000BaseT(X)Ports,Q-ODC Fiber Connector TN-4516A-12PoE-2GPoE-2GODC models:2 TN-4528A-16PoE-2GPoE-2GODC models:2Standards IEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1X for authenticationIEEE802.3for10BaseTIEEE802.3ab for1000BaseT(X)IEEE802.3ad for Port Trunk with LACPIEEE802.3af/at for PoE/PoE+outputIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.3z for1000BaseSX/LX/LHX/ZXEthernet Software FeaturesBroadcast Forwarding Broadcast forwardingConfiguration Options Command Line Interface(CLI)through Serial/Telnet/SSHWeb Console(HTTP/HTTPS)Windows UtilityFilter GMRPGVRP802.1Q VLANPort-based VLANStatic MulticastMulticast FilteringIGMP Snooping v1/v2/v3IGMP QuerierDHCP FilterManagement IPv4/IPv6Flow controlLLDPICMPPort MirrorQoS/CoS/ToSRMONSMTPSNMP InformSNMP TrapSNMPv1/v2c/v3SyslogAccount ManagementLoop ProtectionDNS ServerDHCP option82(relay agent)Port-based DHCP ServerDHCP Server(options1/3/12/15/42/50/55)DHCP Client(options1/3/50/51/53/54/55/57/66/67)MIB Bridge MIBEthernet-like MIBMIB-IIP-BRIDGE MIBQ-BRIDGE MIBRMON MIB Groups1,2,3,9RSTP MIBRedundancy Protocols MSTPRSTPSTPTurbo ChainTurbo Ring v1/v2Turbo Ring with DRCStatic Port TrunkLACPSecurity Access control listTrust access controlBroadcast storm protectionTACACS+RADIUSHTTPS/SSLSSHRate LimitTime Management IEEE1588PTP v1/v2NTP Server/ClientSNTP Server/ClientSwitch PropertiesIGMP Groups256Max.No.of VLANs64VLAN ID Range VID1to4094Jumbo Frame Size9.712KBLED InterfaceLED Indicators PWR1,PWR2,FAULT,MSTR/HEAD,CPLR/TAIL,Ethernet ports,PoE ports Serial InterfaceConsole Port M12A-coded male connectorPower ParametersInput Current TN-4512A models:Max.0.30A@24VDCTN-4516A non-PoE models:Max.0.33A@24VDCTN-4516A non-PoE4GTX/4GTXBP models:Max.0.62A@24VDCTN-4516A PoE models:Max.7.0A@24VDCTN-4520A models:Max.7.0A@24VDCTN-4524A models:Max.6.5A@24VDCTN-4528A models:Max.7.0A@24VDCInput Voltage24/36/48/72/96/110VDCNo.of Power Inputs2Power Connector M23connectorOperating Voltage16.8to137.5VDCOverload Current Protection SupportedReverse Polarity Protection SupportedTotal PoE Power Budget TN-4500A PoE models:120WPhysical CharacteristicsDimensions TN-4512A models:199.8x115x82.3mm(7.87x4.53x3.24in)TN-4516A non-PoE models:229.6x115x82.3mm(9.04x4.53x3.24in)TN-4516A non-PoE4GTX/4GTXBP models:229.6x115x92.3mm(9.04x4.53x3.63in)TN-4516A PoE models:229.6x115x122.3mm(9.04x4.53x4.82in)TN-4520A models:279.6x115x122.3mm(11.00x4.53x4.82in)TN-4524A/4528A models:347.8x115x122.3mm(13.70x4.53x4.81in)Housing MetalIP Rating IP42Weight TN-4512A models:1,032g(2.28lb)TN-4516A non-PoE models:1,248g(2.75lb)TN-4516A PoE models:2,090g(4.61lb)TN-4516A fiber(ODC)models:2,180g(4.81lb)TN-4520A models:2,292g(5.05lb)TN-4524A models:2,388g(5.27lb)TN-4528A models:2,559g(5.64lb)TN-4528A fiber(ODC)models:2,645g(5.83lb)Installation Wall mountingProtection TN-4500A Series-CT models:PCB Conformal CoatingEnvironmental LimitsOperating Temperature-40to70°C(-40to158°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Altitude3000mStandards and CertificationsEMC EN55032/35EMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFFreefall IEC60068-2-31Radio Frequency FCCRailway EN50121-4EN50155IEC60571Railway Fire Protection EN45545-2Safety UL62368-1IEC62368-1EN62368-1Shock IEC60068-2-27,IEC61373,EN50155Vibration IEC60068-2-64,IEC61373,EN50155DeclarationGreen Product RoHS,CRoHS,WEEEMTBFStandards Telcordia SR332Time TN-4512A models:816,541hrsTN-4516A non-PoE models:815,913hrsTN-4516A non-PoE4GTX models:755,975hrsTN-4516A non-PoE4GTXBP models:624,458hrsTN-4516A PoE models:459,971hrsTN-4516A PoE2GTXBP models:434,683hrsTN-4516A PoE fiber(ODC)models:413,810hrsTN-4520A models:437,198hrsTN-4524A models:453,479hrsTN-4528A models:421,101hrsTN-4528A2GTXBP models:398,146hrsTN-4528A fiber(ODC)models:380,761hrsWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x TN-4500A Series switchInstallation Kit2x cap,female,metal,for M12port(console and relay ports,fixed on switch)6/8/10/12/14x cap,male,metal,for M12port(Ethernet ports,fixed on switch)1x wall-mounting kitDocumentation1x quick installation guide1x warranty cardDimensionsTN-4512A ModelsTN-4516A Non-PoE ModelsTN-4516A Non-PoE4GTX/4GTXBP ModelsTN-4516A PoE ModelsTN-4516A PoE Fiber(ODC)ModelsTN-4524A ModelsTN-4528A Fiber(ODC)Models Ordering InformationModel Name10/100/1000BaseT(X)PortsQ-ODC FiberConnector10/100/1000BaseT(X)PortsM12X-Coded8-Pin FemaleConnector10/100/1000BaseT(X)PortsM12X-Coded8-Pin FemaleConnector withBypass Relay10/100BaseT(X)PortsM12D-Coded4-Pin FemaleConnectorPoE Ports10/100BaseT(X),M12D-Coded4-Pin FemaleConnectorPoE Ports100/1000BaseT(X),M12X-Coded8-Pin FemaleConnectorConformalCoatingTN-4512A-WV-T–––12–––TN-4512A-WV-CT-T–––12––✓TN-4516A-WV-T–––16–––TN-4516A-WV-CT-T–––16––✓TN-4516A-4GTX-WV-T–4–12–––TN-4516A-4GTXBP-WV-T––412–––TN-4516A-4GTX-WV-CT-T–4–12––✓TN-4516A-4GTXBP-WV-––412––✓CT-TTN-4516A-12PoE-––––124–4GPoE-WV-TTN-4516A-12PoE-––––124✓4GPoE-WV-CT-TTN-4516A-12PoE-––2–122–2GPoE-2GTXBP-WV-TTN-4516A-12PoE-––2–122✓2GPoE-2GTXBP-WV-CT-TTN-4516A-12PoE-2–––122–2GPoE-2GODC-WV-TTN-4516A-12PoE-2–––122✓2GPoE-2GODC-WV-CT-TTN-4520A-16PoE-––––164–4GPoE-WV-TTN-4520A-16PoE-––––164✓4GPoE-WV-CT-TTN-4524A-16PoE-WV-T–––816––TN-4524A-16PoE-WV-–––816–✓CT-TTN-4528A-16PoE-–––8164–4GPoE-WV-TTN-4528A-16PoE-–––8164✓4GPoE-WV-CT-TTN-4528A-16PoE-––28162–2GPoE-2GTXBP-WV-TTN-4528A-16PoE-––28162✓2GPoE-2GTXBP-WV-CT-TTN-4528A-16PoE-2––8162–2GPoE-2GODC-WV-TTN-4528A-16PoE-2––8162✓2GPoE-2GODC-WV-CT-TAccessories(sold separately)Storage KitsABC-01-M12Configuration backup and restoration tool with M12connector for managed Ethernet switches andwireless APs/Bridges/Clients,0to60°C operating temperatureCablesCBL-M12D(MM4P)/RJ45-100IP67M12-to-RJ45cable,IP67-rated,1mCBL-M23(FF6P)/OPEN-BK-100IP67M23to6-pin power cable,IP67-rated female6-pin M23connector,IP67,1mCBL-M12DMM4PM12DMM4P-BK-M12-to-M12Cat-5E STP Ethernet cable,4-pin D-coded M12connector,IP67,1m100-IP67CBL-M12XMM8P-Y-100-IP67M12-to-M12Cat-5UTP Ethernet cable,8-pin male X-coded crimp type M12connector,IP67,1mCBL-M12XMM8P-Y-300-IP67M12-to-M12Cat-5UTP Ethernet cable,8-pin male X-coded crimp type M12connector,IP67,3m CBL-M12XMM8PRJ45-Y-200-IP67M12-to-RJ45Cat-5UTP Ethernet cable,8-pin male X-coded crimp type M12connector,IP67,2m ConnectorsM12D-4PMM-IP67M12D-coded connector,QUICKON type,4-pin male,IP67M12D-4P-IP68D-coded screw-in sensor connector,male,IP68A-PLG-WPM23-01-IP67M23cable connector,female6-pin,crimp type,IP67M12A-5P-IP68A-coded screw-in sensor connector,female,IP68,4.05cmM12X-8PMM-IP67-HTG X-coded screw-in Gigabit Ethernet connector,8-pin male M12connector,IP67M12Connector CapsA-CAP-M12F-M-PP Metal cap for M12female push-pull connectorA-CAP-M12F-M Metal cap for M12female connectorA-CAP-M12M-M Metal cap for M12male connector©Moxa Inc.All rights reserved.Updated Feb02,2023.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.11。
MOXA 6726交换机配置手册
MOXA6726型交换机配置手册一、确定交换机IP双击“MXconfig”软件。
默认账号：Admin输入密码：moxa点击下图中标记的“搜素”按钮，勾选“工业以太网交换机”选项，点击“搜寻”，根据搜寻结果可知该交换机IP为默认IP：192.168.127.253。
二、本地连接配置1.打开本地连接，右键然后选择“属性”，选择“TCP/IPv4”。
2.勾选“使用下面的IP地址（S）”，输入IP地址：以192.168.127.200为例（不能配置192.168.127.253，否则会IP 冲突）。
三、系统信息设置点击“System”（系统），选择“System Information”（系统信息），为例：Switch Name（交换机名称）：SW-XXX-XXSwitch Location（交换机位置）：XXX点击Apply（应用），每一项配置完成后都需点击Apply。
四、交换机登录输入Username（用户名）:admin默认Password（密码）：moxa五、登录密码修改点击“System”（系统），选择“User Accourt”（用户账号），选定“admin”账户。
Old Password（旧密码）：moxaPassword（密码）：XXXXXXConfirm Password（确认密码）：XXXXXX六、网络设置点击“Network”（网络），选择“IP Setting”（IP设置）。
IP Address（IP地址）：1.8.60.1Subnet Mask（子网掩码）：14（255.252.0.0）Default Gateway（默认网关）：1.8.254.254七、重新登录IP地址修改完成后需在本地连接修改或者添加同一网段IP，然后用修改后IP（1.8.60.1）进行登录，否则将无法进行后续配置。
（本地IP不能配置1.8.60.1，否则会IP冲突）八、日期与时间点击“Date and Time”（日期与时间）Clock Source（时钟源）:NTPTime Server（时间服务器）:1.X.X.XTime Zone（时区）选择（GMT+08:00）九、VLAN设置点击“VLAN”,选择“VLAN Setting”：Management VLAN ID（管理VLAN）设置为100（管理VLAN和端口不一致将导致无法连接交换机，需恢复出厂设置才能再次配置）所有端口VLAN均设置为100，4-1和4-2设置为“Trunk”，并添加VLAN1XXX。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
MOXA交换机使用说明
1、IP地址得设置
通过IE工具来Ping 交换机默认得IP(出厂默认192、168、127、253)地址,进入交换机配置界面后,直接点击确认后,进入交换机设置界面对话框,IP地址设置请选择\Main Meun\Basic Settings\Network,出现下列对话框
在此对话框下,设置人员在Switch IP Address 与 Switch Subnet Mask 旁得空白处填写预定得IP地址(如:192、168、12、20),以及相应得子网掩码地址(如:255、255、255、
0);其她得如Auto IP Configuration 设置为Disable方式,不要选择HDCP方式。
2、主站(Master)设置
完成了IP方式得设置后,就需要对交换得通讯协议与交换机进行相应得设置,选择\Main Menu\munication Redundancy(通讯冗余设置),进入对话框:
在此对话框内,我们需要注意得就是Settings标记下方得设置参量,而Current Status 为相应得设置参量后交换机系统检测后得状态指示。
Redundancy Protocol (通讯协议设置):设置选择为Turbo Ring ,而非就是IEEE802协议(快速生成树)方式;
采用Turbo Ring方式得情况下,需要在网络交换机组中设置一个Master(主站),选择主站得方式就是将Set as Master前得小方框内给予选中, 只需要选择确定后,点击Activate按钮即可生效。
(注意:在多个交换机组成网中只能有1个设置为Master,不可以多选;同时如果不对交换机进行Master设置,系统会自动设置交换机组中得1台为Master)。
Enable Ring Coupling (环间耦合端口定义)在实际得项目运用中不常运用到,在此不给予更多得描述。
需要提醒得就是工程人员在设置过程中不要将Enable Ring Coupling 前得小方格选中,同时要注意得就是对应得Coupling Port与 Coupling Control Port后得端口与前面得Redundant Ports 1st Port与 2nd Port(冗余连接端口定义)设置得端口重复。
3、网络设置参数验证
完成网络参数设置后,对应得munication Redundancy对话框内都通过Current Status 状态给予体现了,包括了网络协议状态、主(Master)/从(Slave)方式;冗余端口得数据监测状态以及环间耦合状态信息。
在多台交换机组环得情况下,工程人员要注意Redundant Ports 1st Port与 2nd Port(冗余端口状态监测状态)得信息:
(1)、Forwarding:(推进状态)
表示交换机得工作状态正常,两个网络冗余连接端口得数据进程稳定。
(2)、Link Down:(断线状态)
表示交换机于相应得连接口连接得数据线存在问题,导致系统监测到为断线状态,需要工程人员进行检查。
(3)、Blocked:(中断状态)
此状态为正常状况,因为Turbo Ring方式在物理上以环得形式存在,而在交换机网络交换时,就是通过一点得Blocked标记来标注环网得虚拟终点,以确定其数据流向得终点。
(4)、Learning:(侦听状态)
此状态在网络出现了断线与恢复得过程中,后备线路得交换机会出现侦听状态,在稳态得情况下,交换机不会出现此信息。
在参数设置完成与网络恢复好后,请检查各交换机得冗余端口状态,正常状况为只有1台交换机得1个端口处于Blocked状态,其她交换机及其端口为Forwarding状态。
4、网络测试验证
对于网络交换机及网络线设置连接完成后,请工程人员尝试将网络冗余线得环给予断开,
以验证网络交换机得运行工作状况如何。
5、关于冗余口得连接方式
(1)、全电口得交换机得连接:诸如408A系列中全电口得,正确得冗余端口连接方式为:
端口7与端口8连接,交互连接形成环形方式。
(2)、光口型交换机得连接方式,诸如:408A、516A系列中SC(ST)型号得设备,正确得冗余端口连接方式如下:
光口交换机1得T1连接光口交换机2得R2,R1连接T2,T2连接R1,R2连接T1;多台交换依此连接方式顺延连接,并最终形成环形结构。
按照非正常方式连接,肯定会造成网络回路得非冗余,同时极有可能因网络数据交换得因素导致网络不稳定或网络风暴现象出现,请各位工程人员严格遵照正确方法进行连接。