五金中英文对照
五金模具常用专业术语中英文对照表(全)
五金模具常用专业术语中英文对照表上模座upper die set 成型公form punch脱料板stripper 垫板subplate/backup plate 下模座die plate 滑块CAM slider垫脚parallel 误检misfeeder托板mounting plate 顶料销kick off初始管位first start pin 带肩螺丝shoulder screw两用销lifter pin 氮气汽缸gas spring弹簧护套spring cage 拔牙螺丝jack screw侧冲组件cam section 导正装置guide equipment漏废料孔slug hole 刀口trim line加强装置enhance equipment 入子insert护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head扣位pocket of head 导柱guide post导套guide bushing 油嘴oil nipple接刀口mismatch/cookie bites 限位块stop block挡块stopper 浮块lifter压块keeper 靠块heel对正块alignment block 简易模prototype tooling检具gage/checking fixture 料带图strip layout闭合高度shut hight 俯视图top view料带strip 公差tolerance正视图front view 走位travel避位/空pocket 退磁demagnetization间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting镀钛TD coasting 沉头counter sink精锣finish mill 线割wire cutting穿丝孔first wire hole 斜度taper镭射laser-cut 上夹板/固定座holder/retainer下模座lower die set 成刑母公forming die电火花EDM 码模槽mounting slot球锁紧固定座ball-lock 导尺rail球锁紧凸模BALL--LOCK 送料板rail plate外购out sourcing 倒角chamfer清角SCRAP CHOPPER 销钉dowel尖角sharp --angle 普通弹簧coil spring展开图EXPENSINg DWG 三打螺丝spool镶件insert 毛刺burr键销key 插针pilot pin顶杆lifter bolt 结构图die layout/design起吊孔handing hole 侧视图cross-section view 垫片shim/wear-plate 退磁DEMAGNETIZATION 键槽key slot 沉孔counter hole储运块storage block 电火花EDM导正块thrust block 剪口直深位trim land手板件prototype unit/part 装备MAURTIG规格spec有效A V AILABILITY五金模具常用专业术语中英文对照表上模座upper die set 下模座lower die set 上夹板holder脱料板stripper 镶件insert 夹板/固定座retainer下模板die plate 成型公form punch 成型母公form die垫脚parallel 垫板sub-plate/backup plate backing plate码模槽mounting slot托板mounting plate 滑块cam slider 导尺rail初始管位first start pin 误检装置misfeeder 送料板rail plate两用销lifter pin 顶料销kick off 键销key止付螺丝set screw 带肩螺丝shoulder screw 销钉dowel弹簧护套spring cage 氮气汽缸gas spring 普通弹簧coil spring侧冲组件cam sections 拔牙螺孔jack screw 三打螺丝spool漏废料孔slug hole 导正装置guide equipment 毛刺burr加强装置enhance equipment 刀口trim line 插针pilot pin护套bushing 入子insert 顶杆lifter bolt止挡板stop plate 整形公restrike forming punch 起吊孔handing hole 扣位pocket of head 挂台head 垫片shim/wear-plate 导套guide bushing 导柱guide post 键槽key slot接刀口mismatch/cookie bites 油嘴oil nipple 靠刀：Heel of cutting punch 固定冲头公夹板：common punch holer 非标易损件：non-standard wearing parts 挡块stopper 限位块（柱）stop block 储运块storage block 压块keeper 浮块lifter 导正块thrust block对正块alignment block 靠块heel 耐磨块：Wear Plate on cutting steel 检具gage/checking fixture 简易模prototype tooling 板件prototype unit/part 料带strip 料带图strip layout 结构图die layout/design 正视图front view 俯视图top view 侧视图：cross-section view 避位/空pocket 间隙clearance 公差tolerance 走位travel 行程stroke 镗孔mill hole 真空热处理vacuum heat treatment 退磁demagnetization 镀钛TD coating 表面处理surface coating 倒角chamfer精锣（缩）finish mill 沉头counter sink 沉孔counter hole 穿丝孔first wire hole 线切割（缩）wire cutting 电火花（缩）EDM 镭射（缩）laser-cut 斜度taper 剪口直深位trim land常用工序名称1.pilot pierce 导正冲孔2.trim 飞边/切边3.idle 空步4.draw 拉伸5.flange 翻边/围边6.forge/coin 镦薄7.repress 回压8.restrike 整形9.reel 卷圆10.ribbon 压筋11.draw hole 翻孔/抽牙nce 切舌刺破13.flatten 拍平14.coin burr 压毛刺/拍披锋/面压15.cut off 切断/切离铭牌信息Tool No. (模具编号)Part No. (产品编号)Part name (产品名称)Stock thickness (材料厚度)Stock width (料宽)Progression (步距)Shut height (闭合高度)Feed height (送料高度）Tonnage (吨位)Total die weight (模具总重量)Upper die weight (上模重量)。
五金相关词汇中英文对照剖析
五金相关词汇中英文对照Normteile 标准件Gewinde, Schrauben, Muttern 螺纹、螺栓、螺母Gewinde 螺纹Schrauben 螺栓Gewindeauslufe 螺纹收尾、肩距Gewindefreistiche 螺纹退刀槽Senkungen 锪孔、沉孔Mutter 螺母Scheibe 档圈Schl tsselweite 扳手口尺寸Werkzeugvierkante 工具四方柄Stifte, Bolzen, Niete, MitnehmerverbindungStifte 圆柱销Kerbstifte 弹性销Bolzen 轴销Keile 键Federn 弹簧Keilwellenverbindung 花键连接Blindniete 抽芯铆钉Werkzeugkegel 刀具、工具锥度Normteile f r Vorrichtungen und Standzwerkzeuge 工装夹具和冲裁模具的标准件Normteile f r Vorrichtungen工装夹具的标准件T-NutenT 型槽Kugelscheiben 球面垫圈Normteile f r Stanzwerkzeuge 冲裁模具标准件Federn 弹簧Antriebstechnik 传动技术RiementriebeV 型带传动Gleitlagerbuchsen 滑动轴承轴瓦W?lzlager 滚动轴承Nutmuttern 圆螺母Passscheiben配合垫圈St t tzscheiben 调整垫圈Wellenenden 轴端Wellendichtring 轴用密封件RunddichtringO 型密封圈机械工具Mechanic“s Toosl spanner 扳子（美作:wrench） double-ended spanner 双头扳子adjustablespanner, monkey wrench 活扳子,活络扳手box spanner 管钳子（美作:socket wrench） calipers 卡规pincers, tongs 夹钳shears 剪子wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯rivet 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈staple U 形钉grease gun 注油枪oil can 油壶jack 工作服机械加工抛光polishing 安装to assemble 扳手wrench 半机械化semi-mechanization; semi-mechanized 半自动滚刀磨床semi-automatic hob grinder 半自动化semi-automation; semi-automatic 备件spare parts 边刨床side planer 变速箱transmission gear 柄轴arbor 部件units; assembly parts 插床slotting machine 拆卸to disassemble 超高速内圆磨床ultra-high-speed internal grinder 车床lathe; turning lathe 车刀lathe tool 车轮车床car wheel lathe 车削turning 车轴axle 衬套bushing 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC 刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬（软）板（片）材及自由发泡板机组Heat preserving furnaces 保温炉Q出工凹:日目lejuozuoii'sjajuao 6uiu!i|oe|/\|Q申工凹宙爵lejauaB'sjajuao 6uiu!qoe|/\|刑耿眾sjojeouqnn 腸玄歇風siuejsAsuoneouqn-i 邈歇風sjueouqnn 谢多爭军|E0屮"90屮叭谢多涉単jajjnrsemen 谢多蜜豊peeds-i|b!i|'sei|iEi 谢多匪重心np-Meaii1 semen 谢多匝目ORBIU o『e'semen呂#工谢多LpuoqoiiiEi l!suo】s 丄|/\is」6Bu^no jasenPIMW 6umno jase-| 刑披耿Q工ssaijajuao'sauiqoeiu Buidden 刑披耿sauiiioeiu 6uidde-| WW sb『册|回壬做sjapui|Ao A JBJOJ 0肿ejpAn 曲直田蚩squn」a/v\od sinejpAn 菅工壬做SQOI」a/v\od sinejpAn 秋IZ刃邈sjuauodiuoosinejpAn 刑曇團sauiiioeiu 6UIUOH 出if®请物seoeunj juaiujeaj; 6uneaH Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P 型PVC 高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe &tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手。
五金词汇中英文对照
五金词汇中英文对照我们的生活中五金产品随处可见，那么你知道他的英文的意思吗?下面是小编给大家带来的五金词汇中英文对照，欢迎大家阅读参考，我们一起来看看吧!五金词汇中英文对照Normteile标准件Gewinde, Schrauben, Muttern螺纹、螺栓、螺母Gewinde螺纹Schrauben螺栓Gewindeauslufe螺纹收尾、肩距Gewindefreistiche螺纹退刀槽Senkungen锪孔、沉孔Mutter螺母Scheibe档圈Schlüsselweite扳手口尺寸Werkzeugvierkante工具四方柄Stifte, Bolzen, Niete, MitnehmerverbindungStifte 圆柱销Kerbstifte弹性销Bolzen轴销Keile 键Federn弹簧Keilwellenverbindung花键连接Blindniete抽芯铆钉Werkzeugkegel刀具、工具锥度Normteile für Vorrichtungen und Standzwerkzeuge工装夹具和冲裁模具的标准件Normteile für Vorrichtungen工装夹具的标准件T-NutenT型槽Kugelscheiben球面垫圈Normteile für Stanzwerkzeuge冲裁模具标准件Federn弹簧Antriebstechnik传动技术RiementriebeV型带传动Gleitlagerbuchsen滑动轴承轴瓦W?lzlager滚动轴承Nutmuttern圆螺母Passscheiben配合垫圈Stützscheiben调整垫圈Wellenenden轴端Wellendichtring轴用密封件RunddichtringO型密封圈机械工具Mechanic“s Toolsspanner 扳子 (美作:wrench1)double-ended spanner 双头扳子adjustable2 spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench)calipers3 卡规pincers, tongs4 夹钳shears5 剪子wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge6 孔径规hacksaw 钢锯rivet7 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg8, dowel 销钉washer 垫圈staple9 U形钉grease gun 注油枪oil can 油壶jack10 工作服机械加工抛光 polishing安装 to assemble扳手 wrench半机械化 semi-mechanization; semi-mechanized 半自动滚刀磨床 semi-automatic hob grinder半自动化 semi-automation; semi-automatic备件 spare parts边刨床 side planer变速箱 transmission gear柄轴 arbor11部件 units; assembly parts插床 slotting machine拆卸 to disassemble超高速内圆磨床 ultra-high-speed internal grinder 车床 lathe12; turning lathe车刀 lathe tool车轮车床 car wheel lathe车削 turning车轴 axle衬套 bushing 按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Drawing machines 拔丝机Drilling machines 钻床。
五金工具中英文对照
两用扳手CONBINATION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET 两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINATION RATCHET SPANNER SET1/4'连接物ADAPTOR 1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RATCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS1/4一字，十字，星型，内六角旋具套筒1/4’双向棘轮套筒扳手1/4’REVERSIBLE RATCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RATCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER 1/4 TO 3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，内六角旋具套筒3/8六角套筒SOCKET HEXAGON 3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RATCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS1'.....风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON 摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH3C米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手HEXAGON SOCKET KEY加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER 6-24V150-250伏测电笔VOLTAGE TESTER 150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE 小钢丝钳SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳ELECTRICIAN’S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳电话钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH 30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN’S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMATIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES 同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING VARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4 WAY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具VALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS’S BALL PEIN HAMMER钳工锤ENGINEERS’S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS’BALL PEIN HAMMER胡桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS’HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS 大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PAVING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH’S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP冲子组套DRIFT PUNCH SET铆钉装配器RIVET SETTER字母及数字冲子LETTER AND NUMBER PUNCHES装配冲子SETTING PUNCH撬杆PRVBAR起钉器NAIL FIFER OCTAGONAL撬棍CROWBAR通用拉马UNIVERSAL PULLER两爪拉马PULLER 2-ARM PATTERN三爪拉马PULLER 3-ARM PATTERN防腐蚀拉马COROSTOP PULLER PATTERN快速拉马QUICK-ACTION PULLER两爪液压拉马UNIVERSAL 2-ARM PULLER拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL 2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET内提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBLY FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES 管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜WARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLLYE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶WASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINATION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER’S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY 分类垃圾收集站WASTE-COLLECTION STATION CONTAINER立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备TORQUE TESTER AND EQUIPMENT扭距倍增器TORQUE MULTIPLIERS扭距角度指示器TORQUE ANGLE INDICATORS特殊DREMO工具SPECIAL DREMO TOOLSDREMOMETER系列扭力工具DREMOMETER TOOLS扭距螺丝刀TORQUE SCREWDRIVERS扭距扳手/扭力扳手TORQUE WRENCHES电子扭距测试仪ELECTRONIC TORQUE TESTERDKD校准遵守DKD准则3-7/3-8/DIN EN ISO 6789RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准迷你型扭距扳手DREMOMETER MINIDREMOMETER高强度铝合金扭距扳手含：DREMOMETER 1-12NM /10-100LBF.IN （塑料外表）DREMOMETER 6-30NM /50-270LBF.INDREMOMETER 8-40NM /70-350LBF.INDREMOMETER 20-120NM /15-90LBF.FTDREMOMETER 40-200NM /30-150LBF.FTDREMOMETER 50-300NM /35-220LBF.FTDREMOMETER 80-360NM /60-260LBF.FTDREMOMETER 110-550NM /80-405LBF.FTDREMOMETER 140-760NM /105-560LBF.FTDREMOMETER 520-1000NM /380-730LBF.FTDREMOMETER 750-2000NMDREMOMETER 1500-3000NMDREMOMETER系列棘轮头RATCHET HEADS DREMOMTER扭距限制接合器TORQUE LIMIT UNIT转角仪TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖范围8-1000NM）开口扳子头OPEN END RTTING梅花扳子头RING END RTTING半开口梅花扳子头FLARED END FITTING棘轮头RATCHET HEAD四方头FIXED SQUARE HEAD方形插头式扭距扳手（覆盖范围8-400NM）开口插头RECTANGULAR OPEN END RTTING梅花插头RECTANGULAR RING END RTTING半开口梅花插头RECTANGULAR FLARED END RTTINGTORCOFIX系列带四方驱动的扭距扳手TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含：4549-01 1-5NM 1/4’方头4549-02 2-25NM 1/4’方头4549-05 5-50NM 3/8’方头4550-10 10-100NM 1/2’方头4550-20 20-200NM 1/2’方头4550-30 60-300NM 1/2’方头4550-40 75-400NM 1/2’方头4550-55 100-550NM 3/4’方头4550-75 140-750NM 3/4’方头TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SETTORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K蘑菇头MUSHROOM HEADTORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX ZTORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FS TORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCHTORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERSFS型扭距螺丝刀范围0.02-13.6NMS型扭距螺丝刀范围0.05-9NMSP型扭距螺丝刀范围10-500CNMTSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH 范围3-125NMTBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH 范围0.2-135NM。
五金产品中英文对照
大力钳 滑轮 锄头 尘掸 马桶吸 蹲便器 生料带 环氧胶 水表 出峰 套筒扳手组 成套六角螺丝套头 成套12花套筒 大力钳 游标卡尺 划刀 刮刀 铆钉枪 砂轮 护目镜 千斤顶 套筒扳手 弯头套筒扳手 焊条 直角尺 水平尺 万向轮 合页，铰链 PVC膨胀管 独轮手推车 钢锯条 角阀 闸阀 蝶阀 球阀 蹲便器
配电箱 镀锌挫丝钉 光杆水泥钉 不锈钢铁丝网 电器 逆变器 过载保护 短路 电压 电流 转换器 额定电压 真空管 绝热 支架 辅助箱 孔径面积
distribution box galvanized twist-nails smooth concrete nail stainless steel wire mesh inverter overload protection short circuit voltage current converter rated voltage vacuum tube heat insulation bracket auxiliary tank aperture area
铸铁管 异径弯头 半径弯头 短半径弯头 长半径180度弯头 三通 四通 活接头 堵头 短节 异径短节 斜舌 方舌 镀彩锌 锁芯 浮球开关 扁形磷铜焊丝 水泥钉 没头水泥钉 刺绳 空气压缩机 电锤 剪枝机 果枝剪 大力剪 钢丝刷套件 电焊网 角磨 套筒扳手 货仓车 干壁钉/墙用螺丝 十字头 脚轮 平板推车 轮辐 全抛釉瓷砖
中文 预计到达时间 锤子 钢镐头 把镐 八角锤头 石工锤头 破石锤头 木柄石工锤 纤维柄石工锤 半包塑柄石工锤 木柄八角锤 木柄抛光八角锤 木柄圆头锤 黑漆头羊角锤 钳工锤 扁尾八角锤 起钉器 撬棍 八角扁刃石工凿 八角尖刃石工凿 八角扁刃胶套石工凿 厨卫浴 花洒顶喷 花洒 顶喷 吊头 妇洗器 皂液器 壁架 淋浴管 吸塑 沐浴升降 地漏
五金相关词汇中英文对照
Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手Gewinde, Schrauben, Muttern螺纹、螺栓、螺母Gewinde螺纹Schrauben螺栓Gewindeauslufe螺纹收尾、肩距Gewindefreistiche螺纹退刀槽Senkungen锪孔、沉孔Mutter螺母Scheibe档圈Schlüsselweite扳手口尺寸Werkzeugvierkante工具四方柄Stifte, Bolzen, Niete, MitnehmerverbindungStifte 圆柱销Kerbstifte弹性销Bolzen轴销Keile 键Federn弹簧Keilwellenverbindung花键连接Blindniete抽芯铆钉Werkzeugkegel刀具、工具锥度Normteile für Vorrichtungen und Standzwerkzeuge工装夹具和冲裁模具的标准件Normteile für Vorrichtungen工装夹具的标准件T-NutenT型槽Kugelscheiben球面垫圈Normteile für Stanzwerkzeuge冲裁模具标准件Federn弹簧Antriebstechnik传动技术RiementriebeV型带传动Gleitlagerbuchsen滑动轴承轴瓦W?lzlager滚动轴承Nutmuttern圆螺母Passscheiben配合垫圈Stützscheiben调整垫圈Wellenenden轴端Wellendichtring轴用密封件RunddichtringO型密封圈机械工具 Mechanic“s Toolsspanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench) calipers 卡规pincers, tongs 夹钳shears 剪子wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子drill 钻chuck 卡盘scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯rivet 铆钉nut 螺母locknut 自锁螺母,防松螺母bolt 螺栓pin, peg, dowel 销钉washer 垫圈staple U形钉grease gun 注油枪oil can 油壶jack 工作服机械加工抛光 polishing安装 to assemble扳手 wrench半机械化 semi-mechanization; semi-mechanized半自动滚刀磨床 semi-automatic hob grinder半自动化 semi-automation; semi-automatic备件 spare parts边刨床 side planer变速箱 transmission gear柄轴 arbor部件 units; assembly parts插床 slotting machinePipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒。
学习五金中英文入手,五金中英对照(中英语对照)--(新带真人朗读学习英语功能)
Satin Nik + Shining Nik Matt White Satin Nik+Deep Satin Alu Satin Nik+Deep Satin White Slight Satin AL. Slight Satin AL + Satin Chrome Polish + Lacquer Alu+White Paint White Paint White Paint + Chrome Brown Paint 8K Board+Shining Nik Pearl Chrome Alu. Satin Gold + Gold Plated Shining Alu with Deep Satin+White paint Chrome+Zincification Deep Satin +White Paint Slight Satin with Stainless steel Deep satin with shining black Rusty Anti Brass Brown Painted Black Nik Chrome+Deep satin white Strong shining silver 3 Chrome 3 Chrome+Alu brass Anti Green Milk White Painted 3 Chrome+Electrolyze Chrome Ivory white brush gold Black Brush Gold Matt Alu with Slight Satin+3Chrome Rice Gold Gold matt Satin Gold Brush Brown Chrome+8K Stainless steel Chroh Deep Satin Chrome + Satin Gold Red Gold Brush Grey
(中英文对照)五金家具专业词汇
(中英文对照)五金家具专业词汇Secret-hinge 暗铰Semifinished furniture product and accessories 家具半成品及配件Semifinished product for interior fittings 装潢用半成品Simple connecting fittings 简单五金配件Single item 单项产品Sliding door roller series 推拉门用轮系列Stra大庆翻译公司ight-lock 企口锁Surface gluing 板面上胶Veneer trimming 薄片整修Vertical upright 直挂格Wood-button 木纽Wood components 木制配件Wooden bar 车件Wooden cork 木塞Wooden curtain rod and ring 木制窗帘杆及吊环Woodscrew 木螺钉Wreathed hand-rail 扭弯扶手Ball bearing slide脚轮滑道Bolt pin 螺栓插销Bolts and nuts for furniture 家具用螺钉，螺帽Brass 铜Carcase 框架，架子Castor 小脚轮Ceiling 天花板Central hinges 中央铰链Chrome 铬Complete range of drawer slide 各种类型的抽屉滑道Component 零配件，元件Concealed hinge 内藏铰链Cupboard-lock 拒门锁Decorative trims for furniture 家具金边饰条Door & window 门窗Drawer-lock 抽屉锁Drawer runner 抽屉滑槽Equipment for surface treatment 表面处理工具3/4 extension slide 部分开式滑道Faucet 水龙头Fixture 固定装置Full extension slide 全开式滑道Furniture fittings 家具五金Furniture hardware家具五金Furniture parts 家具零配件Furniture structural parts 家具结构零件Gas lift chassis 气压棒底盘Glass door hinge 玻璃门铰链Heavy duty slide 承重式滑道Hook lock 钩锁Keyboard slide 键盘板滑道Large head type 大头型Locating dowel 定位榫钉Lock rail 安锁冒头Magnetic catch 磁性拉手Magnetic-lock 磁锁magnetic push latch磁性撞锁Marquetry work镶嵌装饰品Material 原材料Metal fittings 金属配件Matal handle 金属拉手Mold模具Office chair central tube accessories 办公椅中管配件Office chair hardware accessories 办公椅五金配件Out set 外盖型套轮Panel veneer 板料Plastic 塑料Plastic bolt and threaded axis 塑料螺帽及牙轴Pocket door slide 柜门滑道Prevent falling off due to turning 防止旋转脱落。
五金冲压中英文术语
英文中文(riveted)nut (壓鉚)螺母(un)thread (不帶)螺紋acc. To﹕according to 依照﹐由...自定adhesion 親和力AFP﹕Anti-Fingerprint 抗指紋anticorrosive treament 防腐處理,argon welding 氬焊,bend relief 折彎工藝口,brass 黃銅,bronze 銅錫合金,bulge 擠料﹐凸出,burred hole 抽孔burring(BR) 抽牙,captive screw,knurled screw,unloseable screw thumb screw ﹐pannel screw 彈簧螺釘,松不脫螺釘,指旋螺釘,面板螺釘,clinch,snap 壓鉚,coining 打磨,convex 凸點,csk﹕countersink,clearance hole 沙拉孔,CTF dimesion﹕CriticalToFunction dimesion 功能尺寸deburr(ing),burr free 去毛刺,diverge 開縫﹐分離﹐不密合,deform 變形,degreasing 除污"dowel convex,orientate pillar,half shear,,semi-pierce" 定位斷差突EC﹕Engineer Change/Electronic Commerce 工程變更/電子商務elctroplate,plate 電鍍,electrogalvanize 鍍鋅,emboss(ing),dimple 凸點EMI﹕Electro Magnetic Interference 電磁干擾,EPA﹕Environmental Protection Agency 美國環保署Erichesn cupping test 埃里克森杯突試驗,extrude/extrusion,protrude 抽孔﹐抽凸extruded tapped hole 抽牙孔,fastener 緊固件﹐鉚釘,finish 表面處理flared (rivet)﹐punch rivet﹐integral rivet,stake,swage 抽孔鉚合fllush 平齊,foam 泡沫,fracture 斷裂,gasket 墊圈﹐墊片,graining 拉絲,hardware 五金件hatchet 壓三角補強,hem 折彎,hexagon 六邊形,hot dip galvanized steel 熱浸鍍鋅板hot-rolled,cold-rolled 熱軋,/冷軋,insulation 絕緣,leveler 軋平機masking (area)﹔free of fog of lacquer 烤漆保護（區域）,MO﹕Manufacture Order 制令mount(ing) 安裝,nearside/farside 正/反面,nickel (鍍)鎳,oblong hole 橢園形孔﹐OB孔ODC'S﹕Ozone Deleting Chemicals 破壞臭氧層的化學物,ODM﹕Original Design&Manufacture 委託設計與製造OEM﹕Original Equipment Manufacture 委託代工,oil,grease 油﹐脂,outsourcing 外購,委外加工overpainting﹔varnish fog 溢漆,painting﹐varnish 烤漆PCI﹕Peripheral Component Interface 周邊元件擴展接口,PCS﹕Pieces ...片﹐...個peel (off),flaking 脫落,perforation 貫通,permanent 不變的；耐久的phosphate treatment 磷化處理,pin,pin standoff 銷,定位銷,PLS﹕places ...處PO﹕Purchase Order 訂單,project 凸出,PS﹕PowerSupport 電源punch direction,stamping direction 沖裁方向,REF.﹕reference 參考,rivet 鉚釘﹐抽孔鉚合﹐拉鉚﹐壓鉚,rusty 生銹,sag side 壓毛邊面,SaltSprayTest 鹽霧測試scratch 刮傷,screw 螺釘,scribe,concave,recess,mark,engrave 刻蝕self-tapping 自攻牙silkscreen,silk print,pad print 絲網印刷slot 縫, 狹槽, 細長的孔SPEC﹕specification 說明〔書〕,規格書,規范spot weld 點焊,stamp 壓印,standoff 支柱﹐螺柱,step standoff 階梯形螺柱stud (壓鉚)螺釘,tab 凸肩,tack weld 縫焊tap(ping) 攻牙tear 拉裂Typ.﹕typical 具有…特征的UNC﹕UniversalNamingConversion 通用命名標准vendor 供應商vent hole 通風孔。
五金中英对照表
SS41、SUS304 FCMB SALE SWRM12、SUS304 BsBM SK-5 SS41、S45C、SUS304 SWRM3、BS SWRH62B、SUS304 SS41 SS41、SUS304 SS41、SUS304 S45C-D S35C、SUS304 S45C-D SS41、SUS304 SALE BsBM BsBM SALE SS41(镀锌)、SUS304 SS41 SS41
平垫圈 塞头 压力计 十字圆头螺丝 铜管接头-扣环 扣环 直销 开口销 弹簧垫圈 四角固定螺栓 螺桩 T型螺帽 单斜边健 斜销 单斜边带头健 U型螺栓 防松螺帽 铜管接头-套接L字型 铜管接头-套接T字型 真空计 碟型螺帽 轴承环扣 轴承垫圈
PLAIN WASHER PLUG PRESSURE GAUGES ROUND HEAD SCREW SLEEVE RETAINING RING S. PIN SPLIT PIN SPRING WASHER SQUARE HEAD SET SCREW STUD-BOLT T NUT TAPER KEY TAPER PIN TAPER-G-KEY U BOLT U NUT UNION ELBOW UNION TEE VACUUM GAUGE WING-UNT B. R. G. LOCK B. R. G. WASHER
零件-中英文对照表
输入中文名称 气压控制元件 轴承环扣 轴承螺帽 轴承垫圈 球塞凡而 90°弯头 环首螺栓 内牙直型铜管接头 内牙铜管接头-L型 法兰 平头螺栓 平行单圆键 平行双圆键 基础螺栓 油杯 油嘴 六角螺栓 六角沈头螺栓 内六角固定螺丝 六角螺帽 铰螺栓 软管接头 铰鍊 键板 敲击螺栓 锁紧卡 锁紧垫圈 直型铜管接头 铜管接头-L型 立布 O环 销 KEY English Name AIR CONTROL UNITS B. R. G. LOCK B. R. G. UNT B. R. G. WASHER BALL VAVEL 90°ELBOW EYE-BOLT FAMALE CONNECTOR FAMALE ELBOW FLANGE FLAT HEAD BOLT FLAT KEY FLAT-R-KEY FOUNDATION BOLT GREASE CUP GREASE NIPPLE HEX. BOLT HEX. SOCKET BOLT HEX. SOCKET SET SCREW HEX. NUT HINGED BOLT HOSE NECK HINGES KEY PLATE KNOCK BOLT LOCK LOCK WASHER MALE CONNECTOR MALE ELBOW NIPPLE O-RONG PIN 依型录 SS41 S35C SS41 依型录 SS或SUS(焊接) 、FC或SCS S25C(锻造) BsBM BsBM FC20、SS41 SWRM12、SUS304 S45C-D S45C-D SS41 BsBM SUS304、BsBM SS41、S45C、SUS304 SCM、SUS304 SS41、SUS304 STPG、SUS304TP SS41、SUS304 SS41、SUS304 S35C、SUS304 SALE SALE BsBM BsBM BsBM RUBBER SS41、S45C、SUS304 材质
五金工具产品中英文对照
两用扳手COＮBINATION ＳPＡNNER两用扳手套装ＣOMBIＮAＴIＯN SPANNＥＲSET加长型两用扳手COＭBＩＮATIOＮＳPANＮEＲEXTＲA LONG梅花棘轮开口扳手ＯPＥN ENDED SPＡＮNEＲWＩTH RIＮG ＲATCＨEＴ梅花棘轮开口扳手套装OPＥN EＮDED SPAＮNＥR WITＨRING ＲAＴCHEＴSＥT ﻫ两用棘轮扳手COMBINＡTＩＯN ＲAＴCＨET ＳPＡNNER ﻫ两用棘轮扳手套装COMBＩNAＴIＯＮRAＴCHET SPＡNNEＲSＥT ﻫ１/４’连接物AＤAＰTＯR １/4' ﻫ组合支架工具COＭＢＩNATION HOLD ＩNG TOＯL ﻫ小型发光二极管MINＩATURE LED ＬAMP ﻫ活动扳手SＩＮGLE ＯPＥN ＥＮDＥD SPANNＥR扳手套装MＡGNETO SPANNER SＥＴﻫ单开口扳手/呆扳手ＳINGLE ＥNDED OPＥN JAW SPANNE R双开口扳手DＯＵＢLE OＰEN ENＤＥD ＳPAＮNER双开口扳手套装DＯＵＢLＥOPEN ＥNDED SPANNER SET扩口螺母扳手ＰLARE ＮＵT SPANＮER（OPＥN）半月型梅花扳手ＨＡLＦ—MＯON RING SPAＮNER ﻫ双头梅花扳手（短)DOUＢLE ENDED SＰＡNNE R（SHORT）ﻫ双头梅花扳手(长)DＯUBLＥEＮDED SPANＮＥＲ（LＯNG) ﻫ平头梅花扳手（直）FLA T RING SPANNER SＴRAIＧHT ＰATTERN ﻫ开口敲击扳手OPEN ＥNDEＤSLOＧGIＮG SPＡNNE R梅花敲击扳手RING SLＯＧＧIＮG ＳPANNER高颈梅花敲击扳手DEEP ＡFＦSET RINＧSLＯGGING SＰＡNＮER直头梅花扳手ＤEEＰＲIＮG SＰANNER（STRAIGHT PATＴERN）延长管EXＴEＮSION TUＢＥﻫ爪型扳手CROＷＦOOT SPＡNNEＲﻫ两用活头扳手CＯMBINATIOＮSWIVEL HEAD ＷRＥＮCH ﻫ活结T型扳手SWIVEL HＡNDＬE WITH SLＩDINＧT ﻫ套筒扳手SOCＫEＴWＲＥNCH ﻫ弯头套筒扳手ANGLＥD ＳＯＣKET WＲＥNCH ﻫ双头套筒扳手DＯUＢLE ＥＮDED SOＣKEＴWRENＣＨﻫ旋棒ＴOＭMＹBAR分节旋棒ＳTEPPＥＤＴOMMＹBAＲ3C把手套筒扳手SOCKEＴWＲEＮCH ＷIＴH 3Ｃ－HANDLE ﻫT型及磁性套筒扳手SＯCＫET WRE ＮCH WITH Ｔ—HＡNDLＥAND ＭAGNET钩头扳手HOCK SPANＮＥR WＩTH LUG带销扳手PIN SＰANＮER ﻫ可调式两爪钩扳手CALIＰER ＦAＣE SPANNEＲWＩＴＨＡDJＵSTA BLＥ1/4’标准六角套筒HEＸAＧON SOCKＥT ﻫ1/4'加长六角套筒HＥXＡGＯN LONG PATTEＲN SOC ＫET ﻫ棘轮扳手RATＣＨEＴS ﻫ套筒ＳＯCKＥＴS ﻫ套筒套装ＳOCKETS SETS摩擦棘轮扳手FＲICTＩON RATCHETS ﻫ冲击工具IMPAＣT ＴOOLS旋具头BITS扭矩扳手TORQUE WＲENCHES1/４梅花套筒SOCKET ＵD ＰROＦＩＬE ﻫ１/4六角套筒ﻫ星型套筒ＳOCKEＴFOR PROTＲUＤIN1/4’双向棘轮套筒扳手1/4'ＲEＶＥＲG HEAD SCREWS ﻫ1/4一字，十字,星型,内六角旋具套筒ﻫSIBＬE RATCHET ﻫT柄棘轮扳手RATCＨET WＩＴH Ｔ—HANDLE ﻫ手用棘轮头HAＮD RAＴCＨＥT WITHOUT HANDLE ﻫ１/4转3／8转换接头CONＶERTEＲ１／4 TO 3／８ﻫＴ型滑动头手柄ＴOMMY BAR WITH SLIDING T ﻫ活动延长杆FＬEXＩＢＬE ＥＸTＥNＳION1/4四方驱动连接头SQUAＲE－DRIＶE COUPＬER 通用延长杆UNIVEＲSＡL-JＯIＮＴEXTENSION ﻫﻫ1/4万向接头ＵNIVERＳAＬJOＩNT ﻫ活动头手柄SWIＶEL HＡＮDＬE ﻫ套筒固定夹SＯCＫEＴR3/8一字，十字,星型,内六角旋具套筒ＡＩＬWIＴH MAGＮＥTＩC ﻫ3／8六角套筒SOCＫET HEXAGOＮ3/８3/8梅花套筒ＳOCKET UD ＰＲOFＩLＥ3/4' 。
五金中英文对照
五金中英文对照门控五金专业术语Terminologies for door control hardware一、地弹簧Floor hinge （Floor spring）Adjustable creep speed 缓行速度Adjust detection sensibility 检测灵敏度调整Adjustment style 调速方式Two-section adjustment 两端调节Buffer 缓冲区Closing section 关门阶段Opening section 开门阶段Center pivoted arm 中心摇臂Top pivot seat 上枢轴座Pivot bottom seat 枢轴底座Offset pivot arm 偏心摇臂Closing force 紧闭力Closing speed 闭门运行速度Opening speed 开门运行速度Non-hold 无驻持Hold 驻持Economic model 经济型Floor hinge （Floor spring）地弹簧Hydraulic control 液压控制Cover plate. 盖板Cam spindle 凸轮轴Sealing compound 密封化合物Environmental-Protection floor hinge 环保型地弹簧Insect prevention 防虫Water proof 防水Keep warm 保温Antirust 防锈Maximum opening angle 最大开启角度Maximum loading 最大门重Maximum loading capacity 最大承重Maximum opening force 最大开门力Non-antomatic pivot hinge 地轴Pivot hinge 地轴Door axial 门轴Top pivot 顶轴Upper pivot 上轴Adjust gasket 调整垫片Bottom Pivot 下轴二、玻璃门夹、驳接件、铰链类Precision-cast door handle 精铸门拉手Precision-cast zinc alloy handle精铸锌合金拉手Precision-cast stainless steel handle精铸不锈钢拉手Single handle单支拉手Wooden handle木质拉手Marble handle大理石拉手卫浴产品术语Terminologies for Bathroom Hardware一、水龙头（Faucet）1.1 水龙头种类1.1.1 Cleaner Faucet 净身器龙头1.1.2 Concealed Faucet 暗式龙1.1.3 Double Handle Faucet 双把龙头1.1.4 Fast On Faucet 快开龙头1.1.5 Kitchen Faucet 厨房龙头1.1.6 Lavatory Faucet 脸盆龙头1.1.7 Pedaled Faucet 脚踏式龙头1.1.8 Shower Faucet 淋浴龙头1.1.9 Shower Nozzle 淋浴喷头1.1.10 Single Handle Faucet 单把龙头1.1.11 Thermostat Faucet 恒温龙头1.1.12 Time-lapse Faucet 延时龙头1.1.13 Versatility Faucet 多功能龙头1.1.14 single hole basin mixer 单孔脸盆龙头1.1.15 double hole basin mixer 双孔脸盆龙头1.1.16 bathtub mixer with shower head 挂墙式浴缸龙头1.1.17 wall-in bathtub mixer 入墙式沐浴龙头1.1.18 Automatic Faucet 感应龙头1.1.19 Basin Faucet 台式龙头1.2 水龙头配件1.2.1 Angle Valve 角阀1.2.2 Cold-water tap 水嘴1.2.3 Shower mixer 淋浴水龙头1.2.4 faucet, mixer tap 明三联式浴缸水嘴1.2.5 shower 淋浴喷头1.2.6 shower curtain 浴盆帘1.2.7 Lever handle 一字型把手1.2.8 Cross handle 十字把手1.2.9 Handle assembly 把手组件1.2.10 Cap 把手上盖1.2.11Post 基座二、化妆镜（Cosmetic Mirror）2.1 安装情况2.1.1 bathroom cabinet 卫生间镜箱2.1.2 round front model 圆形设计2.1.3 oval shape design 椭圆形设计2.1.4 countertop installation 圆台面上安装2.1.5 fixing with back to wall 背靠墙式安装2.1.6 above counter mounting 台上安装2.1.7 under counter mounting 台下安装2.1.8 fixing above table board 柜上安装2.1.9 玻璃门合页（Glass Door Hinge）三、卫浴配件（Bathroom accessory）3.1 挂式配件3.1.1 Fix Clamp 固定夹3.1.2 Support Bar 浴室支撑杆3.1.3 Glass Clamp玻璃夹3.1.4 Connector连接件3.1.5 Mounting 固定座3.1.6 Rail Connecting Block 导轨支撑件3.1.7 Handle 拉手3.1.8 Robber Hook 衣钩3.1.9 towel ring毛巾环3.1.10 towel bar毛巾杆3.1.11 robe hook衣勾3.1.12 paper holder卫生纸架3.1.13 toilet brush holder马桶刷架3.1.14 double towel bar 双档毛巾架3.1.15 soap dish & bath lotion rack 皂碟和洗剂架3.1.16 towel shelf浴巾架3.2 其他配件3.2.1 Position Block 限位器3.2.2 Wheel 导轮3.2.3 Guide Rail 导轨3.2.4 Mounting 固定座3.2.5 Guide track 导槽3.2.6 Mounting Bracket 支撑脚3.2.7 Mount Header Bracket 吊码3.2.8 Hinge 合页3.2.9 Header Corner 角码3.2.10 Indicator Lock 指示锁3.2.11 Grab Bar For the Disabled 残弱人扶手3.2.12 Strip胶条3.2.13 Sink地漏3.2.14 Indicator指示牌3.2.15 crystal水晶3.2.16 shelf架子3.2.17 lamp灯3.2.18 metal grid金属网3.2.19 soap dispenser皂液器3.2.20 glass shelf玻璃平台3.2.21 tumbler holder 牙刷杯架3.2.22 soap holder肥皂架3.2.23 wall mount shower caddy挂墙式花洒3.2.24 shower caddy花洒3.2.25 soap dish皂碟3.2.26 paper towel storage container3.2.27 Paper handkerchief box纸巾盒3.2.28 safety grab bar 安全扶杆3.2.29 tooth brush holder 牙刷架3.2.30 mirror镜子3.2.31 corner shelf 转角架3.2.32 stainless steel push down3.2.33 bin 不锈钢脚踩垃圾桶3.2.34 column basin立柱盆3.2.35 desk basin台盆3.2.36 bathtub浴缸3.2.37 Butt joint对接接头3.2.38 basket 篮子3.2.39 bath towel 浴巾3.2.40 bathrobe 浴袍3.2.41 bathtub 浴缸四、马桶（toilet）4.1 按种类分4.1.1w.c. pan大便器4.1.2 squatting w.c.pan蹲式便器4.1.3 sitting w.c.pan坐式便器4.1.4 wash down w.c.pan 冲落式便器4.1.5 siphonic w.c.pan虹吸式便器4.1.6 siphon jet w.c.pan喷射虹吸式便器4.1.7 siphon vortex w.c.pan旋涡虹吸式便器4.1.8 integral sitting w.c.pan连体式坐便器4.1.9 urinal小便器4.1.10 wall hung urinal壁挂式小便器4.1.11 stall urinal落地式小便器4.1.12 One-Piece Toilet 连体座便器4.1.13 Two-piece toilet 分体座便器4.2 相关配件4.2.1 toilet, lavatory 恭桶。
五金行业中英文对照
五金行业中英对照一、表面处理中英文对照Finish:表面处理Aluminium coloured铝本色Antique black青古铜色Antique pewter古典白Antique silver coloured仿古银色Black nickel plated镀黑镍Blue matt蓝色亚光Brass plated镀铜Bright亮色Bright black亮黑色Bronzed and brushed棕色磨亚光Chrome coloured亮铬色Chrome plated镀铬Chrome plated matt镀铬拉丝Chrome plated polished镀铬抛光Clear透明Copper tinge lightened淡色调亮铜Galvanized电镀Gold coloured matt金色，拉丝Gold coloured polished金色，抛光Lacquered涂漆Matt拉丝Matt black黑色亚光Matt brushed拉丝,亚光Matt fluorescent拉丝，亮光Natural天然的Nickel coloured Natural coloured 镍色本色Nickel plated 镀镍Nickel plated brushed镀镍拉丝Nickal plated matt镀亚光Nickel plated matt brushed镀镍磨砂效果Nickel plated polished镀镍抛光Pewter coloured白蜡色Polished抛光Red matt红色亚光Silver coloured银色Silver coloured anodized银色，阳极电镀Silver coloured matt银色，拉丝Silver coloured matt anodized银色，拉丝，阳极电镀Silver metallized金属银色Stainless steel coloured不锈钢色Stainless steel coloured matt不锈钢色，拉丝Tinted染色Transparent透明White bright亮白色二、材料中英文对照Material:材料Aluminium铝Beech榉木Brass黄铜Carbon碳Cherry樱桃木Glass玻璃Maple枫木Leather 皮革Metal金属Mirror glass镜面玻璃Oak橡木Plastic 塑料Polycarbonate共聚聚乙烯塑料(聚碳酸脂) Rubber橡胶Procelain白瓷Soft rubber软橡胶Stainless steel 不锈钢Steel 钢质Wood 木质Walnut 胡桃木Wenge 柞木Zebrano斑马木Zinc alloy锌合金Stainless steel,quality 1.4301不锈钢1.4301型Stainless steel,quality1.4305不锈钢1.4305型三、安装中英文对照Installation:安装For clamp fixing用夹具安装For clip fixing 用夹子安装For drilling of doors给门打孔安装(开槽安装) For drilling of flaps 打孔安装上翻门For drilling of front panels打孔安装前面板For glue fixing 用胶固定For gluing in胶粘For hooking in 用钩安装For screw fixing 螺丝固定For screwing in 螺丝固定Wall mounting 墙式安装。
五金中英文对照
门控五金专业术语Terminologiesfordoorcontrolhardware一、地弹簧Floorhinge（Floorspring）Adjustablecreepspeed缓行速度Adjustdetectionsensibility检测灵敏度调整Adjustmentstyle调速方式Two-sectionadjustment两端调节Buffer缓冲区Closingsection关门阶段Openingsection开门阶段Centerpivotedarm中心摇臂Toppivotseat上枢轴座Pivotbottomseat枢轴底座Offsetpivotarm偏心摇臂Closingforce紧闭力Closingspeed闭门运行速度Openingspeed开门运行速度Non-hold无驻持Hold驻持Economicmodel经济型Floorhinge（Floorspring）地弹簧Hydrauliccontrol液压控制Coverplate.盖板Camspindle凸轮轴Sealingcompound密封化合物Environmental-Protectionfloorhinge环保型地弹簧Insectprevention防虫Waterproof防水Keepwarm保温Antirust防锈Maximumopeningangle最大开启角度Maximumloading最大门重Maximumloadingcapacity最大承重Maximumopeningforce最大开门力Non-antomaticpivothinge地轴Pivothinge地轴Dooraxial门轴Toppivot顶轴Upperpivot上轴Adjustgasket调整垫片BottomPivot下轴二、玻璃门夹、驳接件、铰链类Bottompatchfitting下夹Upperpatchfitting上夹Toppatchfitting顶夹Bendingpatchfitting曲夹TpatchfittingT形夹FpatchfittingF形夹Lockerpatchfitting锁夹Lockcasepatchfitting锁盒LongPatchfitting长门夹Bottompatchfittingwithlock带锁下夹Bottombracket下驳接件Upperbracket上驳接件Topbracket顶驳接件Bendingbracket曲形驳接件ZBracketZ形驳接件LbracketL形驳接件Glassdoorhinge玻璃门铰链Openingangle开启角度Arcprecise-castpatchfitting弧形精铸门夹Bendingprecise-castpatchfitting曲形精铸门Heavyprecise-castpatchfitting重型精铸门夹Precise-castpatchfitting精铸门夹系列三、门锁类DoorlockseriesFramelessdoorlock、Latchseries无框门锁、插销系列Framedoorlock、latchseries有框门锁、插销系列Profiledoorlockamong型材门中间锁Glassdoorlock玻璃门锁Glassdoorlatch玻璃门插销Closedevice地锁Latch插销四、电锁类ElectriclockseriesControlcenter管理中心Cardreader读卡器Protocolconverter协议转化器Powercontroler电源控制器Electromagneticlock磁力锁Force拉力Actuationcurrent启动电流Inputvoltage输入电压Workingcurrent工作电流Signaldetection侦测信号Electromagneticlockforsingle-leafdoor单门磁力锁Electromagneticlockfordouble-leafdoor双门磁力锁Lockbodysize锁体尺寸ConcealedElectromagneticlockforsingle-leafdoor暗装式单门磁力锁Water-proofelectromagneticlockforsingle-leafdoor单门防水磁力锁Electriclockseries电插销系列Cutoutvoltage断电Controlsignal控制信号Electricbolt电插销Shearlock剪力锁Lockafterpower-off断电上锁Shear剪力Bracket支架Electromagneticdoorsuck电磁门吸Releaseafterpowe-off断电释放Switch开关Max.Current最大电流Securitylevel安全标准Remotecontrol遥控器Remoteoperatingrange遥控距离CardCapacity卡容量RecordCapacity记录量Alarmfunction报警功能WorkingFrequency工作频率Automaticdoordrive自动门机Microwavesensor微波感应器Controller控制器Entensiontemplate扩展模板Safetylight安全光线Sparebattery备用电池Motor马达Creditcard刷卡器Semi-automaticdoor半自动门机Guideraillength导轨长度Sashwidth门扇宽度Recommendbearing推荐重量Topsideinstallation顶部安装Besideinstallation侧面安装Applicablebraket适用支架Anti-jamming抗干扰性能Automaticdoordrivesystem自动门机Datastorage资料存储Detectionarea检测区域Detectionareaadjustment检测区域调整Detectionmethod检测模式Detectiontheory检测原理Delayduration保持延时Delayfunction延时功能Densityoftransimissionfrequency发射频率密度Devicename配件名称Doorbell门铃Doorcoordinator顺位器Doppler信息处理Electricbolt电插锁Electromagneticlock电磁锁Electromagneticlockfordouble-leafdoor双门磁力锁Electromagneticlockforsingle-leafdoor单门磁力锁Extensiontemplate扩展模块Lockinpoweroff断电关门锁Magnetismsignal门磁信号Microwavesensor微波感应器Min.detectionmovementspeed最小检测运动速度Moduleoffunction功能模块Motor马达Multi-functionextentionmodule多功能扩展模块Numberofinfraredbeam光束数Outputwatt输出功率Power电源Powercontroler电源拉制器Programmedmicrocomputer微电脑程序控制器Publiccode公共密码Rateoftransmission传输速率Safetyinfraredbeams安全光线开关Sensorrange感应距离Signaldetection信号侦测Swipecard刷卡Swipecard+code刷卡+密码五、推拉移门类SlidingdoorseriesAutomaticdoordrive制动门机Automaticslidingdoor自动平移门Automaticrevolvingdoor自动旋转门Telescopicslidingdoor伸缩推拉门Concealedslidingdoor隐藏式推拉门Automaticslidingdooroperator自动推拉门自动启闭装置Selfmonitoringradarmotiondetector自我监测雷达运动检测器六、拉手类HandleStainlesssteelhandle不锈钢拉手Roundpipehandle圆型执手Squarepipehandle方型执手Special—sharpedpipehandle异型执手Precision-castdoorhandle精铸门拉手Precision-castzincalloyhandle精铸锌合金拉手Precision-caststainlesssteelhandle精铸不锈钢拉手Singlehandle单支拉手Woodenhandle木质拉手Marblehandle大理石拉手卫浴产品术语TerminologiesforBathroomHardware一、水龙头（Faucet）1.1水龙头种类1.1.1CleanerFaucet净身器龙头1.1.2ConcealedFaucet暗式龙1.1.3DoubleHandleFaucet双把龙头1.1.4FastOnFaucet快开龙头1.1.5KitchenFaucet厨房龙头1.1.6LavatoryFaucet脸盆龙头1.1.7PedaledFaucet脚踏式龙头1.1.8ShowerFaucet淋浴龙头1.1.9ShowerNozzle淋浴喷头1.1.10SingleHandleFaucet单把龙头1.1.11ThermostatFaucet恒温龙头1.1.12Time-lapseFaucet延时龙头1.1.13VersatilityFaucet多功能龙头1.1.14singleholebasinmixer单孔脸盆龙头1.1.15doubleholebasinmixer双孔脸盆龙头1.1.16bathtubmixerwithshowerhead挂墙式浴缸龙头1.1.17wall-inbathtubmixer入墙式沐浴龙头1.1.18AutomaticFaucet感应龙头1.1.19BasinFaucet台式龙头1.2水龙头配件1.2.1AngleValve角阀1.2.2Cold-watertap水嘴1.2.3Showermixer淋浴水龙头1.2.4faucet,mixertap明三联式浴缸水嘴1.2.5shower淋浴喷头1.2.6showercurtain浴盆帘1.2.7Leverhandle一字型把手1.2.8Crosshandle十字把手WORD格式1.3Handleassembly把手组件1.4Cap把手上盖1.5Post基座二、化妆镜（CosmeticMirror）1.1.20安装情况1.2.9bathroomcabinet卫生间镜箱1.2.10roundfrontmodel圆形设计1.2.11ovalshapedesign椭圆形设计1.2.12countertopinstallation圆台面上安装1.2.13fixingwithbacktowall背靠墙式安装1.2.14abovecountermounting台上安装1.2.15undercountermounting台下安装1.2.16fixingabovetableboard柜上安装1.2.17玻璃门合页（GlassDoorHinge）三、卫浴配件（Bathroomaccessory）3.1挂式配件3.1.1FixClamp固定夹3.1.2SupportBar浴室支撑杆3.1.3GlassClamp玻璃夹3.1.4Connector连接件3.1.5Mounting固定座3.1.6RailConnectingBlock导轨支撑件3.1.7Handle拉手3.1.8RobberHook衣钩3.1.9towelring毛巾环3.1.10towelbar毛巾杆3.1.11robehook衣勾3.1.12paperholder卫生纸架3.1.13toiletbrushholder马桶刷架3.1.14doubletowelbar双档毛巾架3.1.15soapdish&bathlotionrack皂碟和洗剂架3.1.16towelshelf浴巾架3.2其他配件3.2.1PositionBlock限位器3.2.2Wheel导轮3.2.3GuideRail导轨3.2.4Mounting固定座3.2.5Guidetrack导槽3.2.6MountingBracket支撑脚3.2.7MountHeaderBracket吊码3.2.8Hinge合页3.2.9HeaderCorner角码WORD格式1.6IndicatorLock指示锁1.7GrabBarFortheDisabled残弱人扶手1.8Strip胶条1.9Sink地漏1.10Indicator指示牌1.11crystal水晶1.12shelf架子1.13lamp灯1.14metalgrid金属网1.15soapdispenser皂液器1.16glassshelf玻璃平台1.17tumblerholder牙刷杯架1.18soapholder肥皂架1.19wallmountshowercaddy挂墙式花洒1.20showercaddy花洒1.21soapdish皂碟1.22papertowelstoragecontainer1.23Paperhandkerchiefbox纸巾盒1.24safetygrabbar安全扶杆1.25toothbrushholder牙刷架1.26mirror镜子1.27cornershelf转角架1.28stainlesssteelpushdown1.29bin不锈钢脚踩垃圾桶1.30columnbasin立柱盆1.31deskbasin台盆1.32bathtub浴缸1.33Buttjoint对接接头1.34basket篮子1.35bathtowel浴巾1.36bathrobe浴袍1.37bathtub浴缸四、马桶（toilet）1.1.21按种类分1.2.18w.c.pan大便器1.2.19squattingw.c.pan蹲式便器1.2.20sittingw.c.pan坐式便器1.2.21washdownw.c.pan冲落式便器1.2.22siphonicw.c.pan虹吸式便器1.2.23siphonjetw.c.pan喷射虹吸式便器1.2.24siphonvortexw.c.pan旋涡虹吸式便器1.2.25integralsittingw.c.pan连体式坐便器WORD格式1.38urinal小便器1.39wallhungurinal壁挂式小便器1.40stallurinal落地式小便器1.41One-PieceToilet连体座便器1.42Two-piecetoilet分体座便器1.1.22相关配件1.2.26toilet,lavatory恭桶。
五金模具常用专业术语中英文对照表
五金模具常用专业术语中英文对照表上模座upperdieset成型公formpunch脱料板stripper垫板subplate/backupplate下模座dieplate滑块CAMslider垫脚parallel误检misfeeder托板mountingplate顶料销kickoff初始管位firststartpin带肩螺丝shoulderscrew两用销lifterpin氮气汽缸gasspring弹簧护套springcage拔牙螺丝jackscrew侧冲组件camsection导正装置guideequipment漏废料孔slughole刀口trimline加强装置enhanceequipment入子insert护套bushing整形公restrikeformingpunch止挡板stopplate挂台head扣位pocketofhead导柱guidepost导套guidebushing油嘴oilnipple接刀口mismatch/cookiebites限位块stopblock挡块stopper浮块lifter压块keeper靠块heel对正块alignmentblock简易模prototypetooling检具gage/checkingfixture料带图striplayout闭合高度shuthight俯视图topview料带strip公差tolerance正视图frontview走位travel避位/空pocket退磁demagnetization间隙clearance真空热外理vacuumheattreatment镗孔millhole表面外理surfacecoasting镀钛TDcoasting沉头countersink精锣finishmill线割wirecutting穿丝孔firstwirehole斜度taper镭射laser-cut上夹板/固定座holder/retainer下模座lowerdieset成刑母公formingdie电火花EDM码模槽mountingslot球锁紧固定座ball-lock导尺rail球锁紧凸模BALL--LOCK送料板railplate外购outsourcing倒角chamfer清角SCRAPCHOPPER销钉dowel尖角sharp--angle普通弹簧coilspring展开图EXPENSINgDWG三打螺丝spool镶件insert毛刺burr键销key插针pilotpin顶杆lifterbolt结构图dielayout/design起吊孔handinghole侧视图cross-sectionview垫片shim/wear-plate退磁DEMAGNETIZATION键槽keyslot沉孔counterhole储运块storageblock电火花EDM导正块thrustblock剪口直深位trimland手板件prototypeunit/part装备MAURTIG规格spec有效AVAILABILITY五金模具常用专业术语中英文对照表上模座upperdieset下模座lowerdieset上夹板holder脱料板stripper镶件insert夹板/固定座retainer下模板dieplate成型公formpunch成型母公formdie垫脚parallel垫板sub-plate/backupplatebackingplate码模槽mountingslot托板mountingplate滑块camslider导尺rail初始管位firststartpin误检装置misfeeder送料板railplate两用销lifterpin顶料销kickoff键销key止付螺丝setscrew带肩螺丝shoulderscrew销钉dowel弹簧护套springcage氮气汽缸gasspring普通弹簧coilspring侧冲组件camsections拔牙螺孔jackscrew三打螺丝spool漏废料孔slughole导正装置guideequipment毛刺burr加强装置enhanceequipment刀口trimline插针pilotpin护套bushing入子insert顶杆lifterbolt止挡板stopplate整形公restrikeformingpunch起吊孔handinghole扣位pocketofhead挂台head垫片shim/wear-plate导套guidebushing导柱guidepost键槽keyslot接刀口mismatch/cookiebites油嘴oilnipple靠刀：Heelofcuttingpunch固定冲头公夹板：commonpunchholer非标易损件：non-standardwearingparts挡块stopper限位块（柱）stopblock储运块storageblock压块keeper浮块lifter导正块thrustblock对正块alignmentblock靠块heel耐磨块：WearPlateoncuttingsteel检具gage/checkingfixture简易模prototypetooling板件prototypeunit/part料带strip料带图striplayout结构图dielayout/design正视图frontview俯视图topview侧视图：cross-sectionview避位/空pocket间隙clearance公差tolerance走位travel行程stroke镗孔millhole真空热处理vacuumheattreatment退磁demagnetization镀钛TDcoating表面处理surfacecoating倒角chamfer精锣（缩）finishmill沉头countersink沉孔counterhole穿丝孔firstwirehole线切割（缩）wirecutting电火花（缩）EDM镭射（缩）laser-cut斜度taper剪口直深位trimland常用工序名称1.pilotpierce导正冲孔2.trim飞边/切边3.idle空步4.draw拉伸5.flange翻边/围边6.forge/coin镦薄7.repress回压8.restrike整形9.reel卷圆10.ribbon压筋11.drawhole翻孔/抽牙nce切舌刺破13.flatten拍平14.coinburr压毛刺/拍披锋/面压15.cutoff切断/切离铭牌信息ToolNo.(模具编号)PartNo.(产品编号)Partname(产品名称)Stockthickness(材料厚度)Stockwidth(料宽)Progression(步距)Shutheight(闭合高度)Feedheight(送料高度）Tonnage (吨位)Totaldieweight(模具总重量)Upperdieweight(上模重量)。
五金类词汇中英文对照
五金类词汇中英文对照钳类PLIERS钢丝钳COMBINATION PLIERS多用钳MULTI-PURPOSE PLIERS鲤鱼钳COMBINATION PLIERS SLIP JOINT水泵钳GROOVE JOINT PLIERS钓鱼钳FISHING PLIERS斜咀钳DIAGONAL SIDE CUTTING NIPPERS尖咀钳LONG FLAT NOSE PLIERS弯咀钳BENT NOSE PLIERS剥线器WIRE STRIPPERS大力钳LOCK WRENCH雷管夹钳CRIMPING PLIERS断线钳或者螺栓切割器BOLT CUTTERS台型断线钳BOLT CUTTERS BENCH TYPE重型拆链期HEAVY DUTY CHAIN CUTTERS拉铆枪HAND RIVETERS焊条钳ECECTRODE HOLDER瓷砖钳TILE NIPPERS篱笆钳FENCE PLIERS旋转打眼钳revolving punch pliers扳手SPANNERS & WRENCHES活络扳手ADJUSTABLE WRENCHES两用扳手COMBINATION WRENCHES双头扳手DOUBLE OPEN END WRENCHES套筒扳手SOCKET WRENCH SET锤类HAMMERS羊角锤CLAW HAMMERS泥工锤MASON'S HAMMERS钳工锤MACHINIST'S HAMMERS八角锤DOUBLE-FACED BLACKSMITH'S HAMMERS 木工锤JOINER'S HAMMERS奶子锤ENGINEER'S BALL-PEIN HAMMERS扁尾锤ENGINEER'S CROSS PEIN HAMMERS安装锤RUBBER HAMMERS螺丝批SCREW DRIVERS水管工具PLUMBING TOOLS管子钳PIPE WRENCHES管子台虎钳HINGED PIPE VICES管子铰板RATCHET DIE STOCKS管子割刀PIPE CUTTERS泥木工具TOOLS FOR MASONRY & WOOD WORKING 切削工具CUTTING TOOLS钢锉STEEL FILES锯SAWS手摇钻HAND DRILLS量刃具MEASURING AND CUTTING TOOLS钢卷尺STEEL TAPE ROLLERS游标卡尺VERNIER CALIPERS直柄麻花钻HSS TWIST DRILL BITS其他工具OTHER TOOLS千斤顶JACKS钢丝刷STEEL WIRE BRUSHES压胶枪CAULKING GUNS农具AGRICULTURAL TOOLS刀类KNIVES剪类SCISSORS园林工具GARDEN TOOLS金属网METAL MESHES镀锌方眼网GALVANIZED SQUARE MESH镀锌电焊网GALVANIZED WELDED WIRE MESH菱形网HEXAGON MESH紧固件FASTENERS螺杆BOLT地脚螺丝ANCHOR BOLT双头螺丝DOUBLE HEAD BOLTS连板螺丝BOLTS WITH PLATE螺母STEEL NUT基础件COMPONENT PARTS轴承BEARING工业链条INDUSTRIAL CHAIN建筑小五金CONSTRUCTION HARDWARES木螺丝WOOD SCREW合页HINGE门锁DOOR LOCK插销BOLT门拉手DOOR PULL滑轮ROLLER阀门VALVES家俱小五金HOUSEHOLD HARDWARES铝合金货架GOODS SHELVES脚轮CASTOR金属椅脚垫GLIDE长管LEG ASSY. PAINTED UPPER/CHROME LOWER WITH GLIDE 短管785 LOWER LEG NON-ADJ. GLIDE CHROME金属底座BASE METAL日用五金HABERDASHERY & HARDWARES小刀KNIFE指甲钳NAIL CLIPPERS汽灯KEROSENE HEATER索具RIGGINGS金属制品METAL PRODUCTS镀镍铁丝NICKEL PLATED IRON WIRE镀锌铁丝GALVANIZED WIRE钢丝STEEL WIRE法兰盘FLANGE杜美丝DUMET WIRE杂项小五金OTHER HARDWARES电工产品ELECTRIC PRODUCTS 电源配电箱POWER DISTRIBUTION BOX 机床电器MACHINE TOOL ELECTRIC ARTICLES继电器RELAY电动机MOTOR变压器TRANSFORMER电动工具POWER-DRIVEN TOOL电焊机ELECTRIC WELDER电焊条WELDING ROD电线ELECTRICAL WIRE花电线FLEX铅酸蓄电池LEAD-ACID STORAGY BATTERY凸轮开关HAND OPERATED STARTER纺织品TEXTILES棉坯布COTTON FABRICS色织布YARN-DYED COYYON FABRICS棉涤纶布POLYSTER/COYYON BLENDED FABRICS毛巾FACE TOWELS餐巾NAPAINS方巾FACE CLOTHS擦机布CLEAN CLOTHS丝绸制品SILK PRODUCTS领带NECKTIES绣品EMBROIDERED PRODUCTS和服腰带KIMONOS & BELTS服装GARMENTS衬衫SHIRTS绣衣EMBROIDERED SHIRTS长西裤WESTERN-STYLE TROUSERS短西裤WESTERN-STYLE SHORTS运动短裤SPORT SHORTS浴衣BATH ROBES睡袍NIGIT GOWNS茄克JACKETST恤衫 T-SHIRTS背心(马甲) VESTS牛仔裤JEANS自行车BICYCLE自行车BICYCLE 16",28"童车BMX 12",16",20"自行车零件BICYCLE PARTS外胎TYBE 26",28"内胎TYBE 26",28"飞轮FREE WHEEL 16T,18T,20T,22T前叉FRONT FORK 26",28"车把HANDLE-BAR 26",28"泥板MUDGUARDS 26",28"链条CHAIN 114L,112L打气筒FOOT PUMP摩电灯DYNAMO LIGHT SET 12V/5.5W 鞍座SADDLE PVC TOP车铃BELL 21/4",25/16",3" 脚蹬PEDALS C.P.4"车锁BICYCLE FRAME LOCK铜丝锁WIRE LOCK 23",27" 缝纫机SEWING MACHINE缝纫机马达SEWING MOTORtoolbox 工具箱bench 工作台vice, clamp 虎钳(美作:vise)saw 锯bow saw 弓锯circular saw 圆锯(美作:buzzsaw) compass saw, scroll saw 钢丝锯fretsaw 细锯handsaw 手锯chisel 口凿cold chisel, burin 冰凿gouge, firmer gouge 半圆凿plane 刨子moulding plane 型刨jack plane 粗刨rabbet plane 槽刨drawknife 刮刀scraper 三角刮刀rasp 粗锉file 锉square 尺miter 斜槽规scriber 近线尺set square, triangle 三角板brace 手拉曲柄锉hand drill 手钻drill, bit 钻,有柄钻gimlet, auger 钻,无柄钻countersink 锥口钻gauge, marking gauge 量规hammer 锤mallet 木槌nail 钉brad 平头钉tack, stud 圆头钉screw 螺丝钉screwdriver 螺丝刀,改锥screw tap 螺丝攻nail puller 拔钉器ruler 尺tape measure 卷尺folding ruler 折尺sandpaper, emery paper 砂纸toolbox 工具箱bench 工作台vice, clamp 虎钳(美作:vise) saw 锯bow saw 弓锯circular saw 圆锯(美作:buzzsaw) compass saw, scroll saw 钢丝锯fretsaw 细锯handsaw 手锯chisel 口凿cold chisel, burin 冰凿gouge, firmer gouge 半圆凿plane 刨子moulding plane 型刨jack plane 粗刨rabbet plane 槽刨drawknife 刮刀scraper 三角刮刀rasp 粗锉file 锉square 尺miter 斜槽规scriber 近线尺set square, triangle 三角板brace 手拉曲柄锉hand drill 手钻drill, bit 钻,有柄钻gimlet, auger 钻,无柄钻countersink 锥口钻gauge, marking gauge 量规hammer 锤mallet 木槌nail 钉brad 平头钉tack, stud 圆头钉screw 螺丝钉screwdriver 螺丝刀,改锥screw tap 螺丝攻nail puller 拔钉器ruler 尺tape measure 卷尺folding ruler 折尺sandpaper, emery paper 砂纸stepladder 高凳,折梯trestle 支架trowel 灰泥镘子float 抹子spatula 抹刀,刮铲brush 刷子paintbrush, brush 画刷roller 滚子scissors 剪子spade 锄fork 叉子shovel 铁锹,铲rake 耙roller 滚压器,碌碡dibble 掘穴机wheelbarrow 小车,独轮车watering can 喷壶garden hose, hosepipe 橡胶软管lawnmower 剪草机shears, garden shears 园艺剪刀pruning shears 修枝剪pruning knife 修枝刀sickle 镰刀scythe 钐刀,钐镰trowel 镘weeding hoe 除草耙seed drill 条播机penknife 铅笔刀glass cutter 玻璃刀plumb line 铅垂线spirit level 水平仪pickaxe 鹤嘴锄(美作:pickax)the axe 斧子(美作:the ax)sledgehammer 长柄大锤bushhammer 石工锤rammer 撞针anvil, beakiron, bickiron, two-beaked anvil 砧,砧子bellows 弹簧awl 锤子beam compass, trammel 长圆规lever 杠杆tyre lever 轮胎撬杠crank 柄soldering iron 焊铁,烙铁blowlamp 吹嘴,吹炬(美作:blowtorch)die 冲模diestock 螺丝攻machine tools 工作母机lathe 车床turret lathe 六角车床milling cutter 铣刀milling machine 铣床electric drill, power drill 电钻grinder, crusher 粉碎机riveter 打铆机rolling mill 轧板机press 压床,冲床drop hammer pile hammer, drop hammer 蒸汽汽锤air hammer, pneumatic hammer 气锤pile hammer 打桩机螺丝类Bolts and Nuts商品名称: Item:BS916 英制六角螺丝带母(丝闩) BS916 Hex Bolts & NutsDIN931-933 (8.8) 拉力公制六角头螺丝DIN931-933 Hex Head Bolt G8.8(8.8) 镀锌公制拉力六角头螺丝DIN931-933 Hex Head Bolt G8.8 Electrogalvanized (8.8) 热浸沿水公制六角头螺丝DIN931-933 Hex Head Bolt G8.8 Hot-Dip Galvanized (10.9)级高强度拉力公制六角头螺丝DIN933-931 Hex Head Bolt G10.9(8.8) 拉力公制六角螺丝母DIN934 (8.8) Hex Nuts(8.8) 镀锌公制拉力六角螺丝母DIN934 Hex Nuts G8.8 Electrogalvanized(8.8) 热浸沿水公制拉力六角螺丝母DIN934 Hex Nuts G8.8 Hot-Dip Galvanized (8.8) 公制幼牙六角螺丝母“8.8”Hex Nuts镀锌公英制牙条长驳母Connectors (Long Huts)镀锌公英制拉力埃砵(拉令) DIN580 Lifting Eye Bolts ZINC镀锌水喉“U”型螺丝带母Electrogalvanized “U”Bolts & Nuts304 (A2) 不锈钢英制六角头螺丝A-2 Stainless Steel Hex Head Bolts304 (A2) 不锈钢英制六角头螺丝A-2 DIN931-933 Stainless Steel Hex Head Bolts 316 (A4) 不锈钢英制六角头螺丝A-4 Stainless Steel Hex Head Screws304 (A2) 不锈钢英制六角螺丝母A-2 Stainless Steel Hex Nuts316 (A4) 不锈钢英制六角螺丝母A-4 Stainless Steel Hex Nuts304 (A2) 不锈钢英制尼龙保险螺母A-2 Stainless Steel Hex Nylon Lock Nuts304 DIN580 不锈钢公英制拉令Lifting Eye Bolts Stainless Steel “DIN580”304 不锈钢水喉“U”型螺丝带母A-2 Stainless Steel “U”Bolts and Nuts普通圆铁钉Common Round Iron NailsDIN934 透明塑料六角螺母DIN934 Nylon Hex Nut NatureDIN125 透明塑料平介子Nylon Flat Washers Nature日本锅盖塑料拉手螺母Stainless Steel G-Type Knob Nuts Black (KG-N) Japan手工具类: Tools:商品名称: Item:炼钳Pipe Chain Wrench喉钳Pipe Wrench平咀钳Combination Plier尖咀钳Long-Nose Plier斜咀钳Diagonal-Cutting Plier鲤鱼钳Combination Slip-Joint Plier大力钳Vise Grips敲锈锤Chipping Hammer w/handle羊角锤Claw Hammer w/handle圆头锤Ball Pein Hammer w/handle八角大锤Sledge Hammer w/handle木工锤Carpenter Hammer w/handle木锤柄Wood Hammer Handle大木锤柄Standard Wood Sledge Hammer Handle粗平扁锉Flat File (1st)中平扁锉Flat File (2nd)幼平扁锉Flat File (3rd)粗?锉Half-Round File (1st)中?锉Half-Round File (2nd)幼?锉Half-Round File (3rd)粗方锉Square File (1st)中方锉Square File (2nd)幼方锉Square File (3rd)粗圆锉Round File (1st)中圆锉Round File (2nd)幼圆锉Round File (3rd)中三角锉Three-Square File板锯Hand Saw铁锯片Hacksaw Blade铁锯架Hacksaw Frame铁锯连铁锯片Hacksaw Frame w/blade石矢尖凿Concrete Chisel石矢扁凿Flat Concrete Chisel铁柄番铲Shovel w/steel handle木柄番铲Shovel w/wooden handle胶辘石矢车仔Single Rubber Wheel Barrow斧头柄Axe Handle细斧头Lumberjack Axe (mini.)中斧头Lumberjack Axe (med.)大斧头Lumberjack Axe (max.)番钉柄Picks Handle番钉头Clay Picks Head番钉连柄Clay Picks w/handle锄头柄Dick Handle锄头Dick铁笔Wrecking Bar白铁剪Tinman Snip蛇头剪Bolt Cutter威也钳Cable Cutter水泵钳Pump Plier锯路钳Saw Set通头丝批Screw Driver磁批Magnetic Hand Screw Driver防滑批High-Torque Screwdriver卜批Nutdriver细他笔Screwdriver Tester大他笔Screwdriver Tester细钢头他笔Steel Head Screwdriver Tester中钢头他笔Steel Head Screwdriver Tester大钢头他笔Steel Head Screwdriver Tester石矢钻咀Masonry Shank Drill锋钢钻咀High Speed Drill套庄锋钢钻咀High Speed Drill Set油压钻咀SDS Plus Shank Drill长身小林式钻咀Auger Bit套庄六角匙Hex Key Set加长套庄六角匙Hex Key Set (extra-long)加长波头套庄六角匙Ball Point Hex Key Set (extra-long) 白叻套庄六角匙S/S Hex Key Set昔士Adjustable Wrench Spanner平身钢凿Flat Steel Chisel木凿Wood Chisel弹弓凿Spring Chisel令梗Combination Wrench套庄令梗Combination Wrench Set令士Offset Box Wrench套庄令士Offset Box Wrench Set六角卜士 6 Point Standard Drive Socket十二角卜士12 Point Standard Drive Socket40T 钻石介木碟Circular Saw Blade (Carbide Tipped) 60T 钻石介木碟Circular Saw Blade (Carbide Tipped) 80T 钻石介木碟Circular Saw Blade (Carbide Tipped) 100T 钻石介木碟Circular Saw Blade (Carbide Tipped) 120T 钻石介木碟Circular Saw Blade (Carbide Tipped) 湿介碟Wet-Cutting Saw Blade干介碟Dry-Cutting Saw Blade云石介碟Masonry Cutter Blade磨碟Abrasive Grinding Wheel拮碟Abrasive Cutting Wheel油辘Paint Roller尼龙辘Nylon Caster有掣尼龙辘Nylon Caster w/brake生铁辘Heavy-Duty Caster平底波辘Ball Caster薄身油扫Economic Paint Brush厚身油扫Delux Paint Brush油灰刀Standrad Scraper细灰池Small Steel Trowel中灰池Medium Steel Trowel大灰池Large Steel Trowel胶泥斗Plastic Bucket铁泥斗Steel Bucket3行钢丝刷Steel Wire Brush4行钢丝刷Steel Wire Brush5行钢丝刷Steel Wire Brush4行铜丝刷Brass Wire Brush5行铜丝刷Brass Wire Brush油石Sharpening Stone扁型钢丝辘Wire Wheel Brush扁型有柄钢丝辘Shank-Mounted Wire Wheel Brush碗型有柄钢丝辘Cup Shank-Mounted Wire Wheel Brush 油灰鎗Caulking Gun铜喉拮打Copper Pipe Cutter胶喉剪PVC Pipe Cutter2脚啤令乍2-legs Gear Puller3脚啤令乍3-legs Gear Puller锋钢令梳High Speed Steel Hole Saw钻石钢令梳Diamond Steel Hole Saw尖尾卜Ratchet Wrench1A 玻璃笔Diamond Glass Cutter2A 玻璃笔Diamond Glass Cutter3A 玻璃笔Diamond Glass Cutter火水笔Oil Cutter细尖凿Standard Bull Point Chisel细平凿Standard Cold Chisel细扁凿Standard Pneumetic Chisel加长尖凿Long Bull Point Chisel中尖凿Extra-Long Bull Point Chisel大尖凿Heavy Duty Bull Point Chisel绿色胶塞Plastic Plug (Green Color)红色胶塞Plastic Plug (Red Color)蓝色胶塞Plastic Plug (Blue Color)。
五金模俗语中英文对照表
五金模俗语中英文对照表1 上模座PUNCH SET2 下模座DIE SET3 上垫板PUNCH PAD4 下垫板DIE PAD5 上夹板PUNCH HOLDER6 下夹板DIE HOLDER7 打背板STRIPPER PAD8 上打板UP STRIPPER9 下打板DOWN STRIPPER10 上模板UP PLATE11 下模板LOWER PLATE12 下垫脚BOTTOM BLOCK13 上垫脚TOP BLOCK14 结构图DIE STRUCTURE DWG15 展开图EXTENSION DWG16 简易模PLAIN DIE17 成形模FORMING DIE18 复合模GANG DIE19 铆合模RIVETING DIE20 冲孔模PIERCE DIE21 连续模FOLLOW DIE22 切边模SHEARING DIE23 冲孔PIERCE24 抽孔DRAW HOLE25 切边TRIM26 折弯BENGING27 凸点EMBOSS28 半剪SEMI-SHEARING29 压毛边DEBURROR COIN30 侧冲压平SIDE STRETCH31 压线GROOVE32 刻印STAMP LETTER33 剪断SHEARING34 下料BLANKING35 铆合RIVETING36 反面压印TICK-MARK NEARSIDE37 正面压印TICK-MARK FARSIDE38 材料MATERIAL39 料厚MATERIAL THICKNESS40 系数FACTOR41 向上UPW ARD42 向下DOWNW ARD43 毛边BURR44 间隙GAP45 正面TOP46 反面BOT（BOTTOM）47 贯穿THR48 沉头CB49 攻牙TAP50 斜度，直边S EDGE51 冲头PUNCH52 入块INSERT53 垫片SPACER54 定位销DOWEL PIN55 浮升销LIFT PIN56 对称形SYM57 同基准/同类型TYP58 CNC线切割W/C59 研磨加工M60 下极点lower dead center61 下模die62 下模座lower bolster/lower shor63 上件feeding/loading64 上件装置feed/feeding equipment65 上极点top dead center66 上模punch67 上模座upper shoe/upper bolster68 工件finished part69 工序件work70 刃口斜度draft angle71 切开lancing72 切边trimming73 切舌lancing74 切断cutoff/cropping75 中性层neutral axis76 中性层系数neutral axis location77 气垫air cushion78 毛刺burr79 毛刺面burr side80 毛面break/fracture81 反拉深reverse redrawing82 反侧压块heel block83 双面间隙total clearanc84 凸模punch85 凹模die/die block/ matrix/die section86 出件unloading87 出件装置unloading device88 闭合高度shut height89 冲孔piercing/punching/perforating90 冲件stamping91 冲缺notching92 冲裁cutting93 冲模die94 冲槽slotting95 夹持送料装置grip feed96 扩口expanding97 压凸swaging98 压花stamping99 压料板（圈）pressure pad/binder/blank holder 100 压料筋（槛）locking bead /raw bead101 压筋beading102 成形forming103 光洁冲裁finish blanking/smooth-edge blanking 104 光面cut band/burnish105 回弹spring-back106 行程stroke107 导正销pilot108 导板guide plate/wear plate109 导柱guide post/guide pin/leader pin/guide pillar110 导柱模架plain guide die set111 导料板stock guide/material guide/guide plate112 导套guide-post bushing/guide-pin bushing113 防护板barrier guard114 间隙clearance115 寿命die life116 扭弯twisting117 连续拉深progressive draw/multi-stage drawing118 连续模（级进模）progressiv die/follow-ontool/multi-stag drawing 119 步距pitch/progression120 条料strip121 定位销（板）gage/pin gage/locating pin/nest plate122 变薄拉深ironing123 废料切刀scrap cutter。
五金工具产品中英文对照
五金工具产品中英文对照两用扳手CONBINA TION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RA TCHET梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET 两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINA TION RATCHET SPANNER SET1/4'连接物ADAPTOR 1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET 钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RA TCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS1/4一字，十字，星型，内六角旋具套筒1/4’双向棘轮套筒扳手1/4’REVERSIBLE RA TCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RA TCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER 1/4 TO 3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，内六角旋具套筒3/8六角套筒SOCKET HEXAGON 3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET3/4' ..旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RA TCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS1'.....风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RA TCHET WITH RING WITH BI-HEXAGON 摩擦式四方棘轮扳手FRICTION TYPE RA TCHET WITH SQUARE RING安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手HEXAGON SOCKET KEY加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER 6-24V150-250伏测电笔VOLTAGE TESTER 150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE 小钢丝钳SMALL COMBINA TION PLIERS钢丝钳（德式）COMBINA TION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINA TION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PA TTERN）电工剪钳ELECTRICIAN’S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PA TTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳电话钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH 30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN’S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMA TIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES 同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING V ARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER 高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4 W AY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具V ALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器V ALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS’S BALL PEIN HAMMER钳工锤ENGINEERS’S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS’BALL PEIN HAMMER胡桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS’HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS 大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PA VING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH’S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP冲子组套DRIFT PUNCH SET铆钉装配器RIVET SETTER字母及数字冲子LETTER AND NUMBER PUNCHES装配冲子SETTING PUNCH撬杆PRVBAR起钉器NAIL FIFER OCTAGONAL撬棍CROWBAR通用拉马UNIVERSAL PULLER两爪拉马PULLER 2-ARM PATTERN三爪拉马PULLER 3-ARM PATTERN防腐蚀拉马COROSTOP PULLER PATTERN快速拉马QUICK-ACTION PULLER两爪液压拉马UNIVERSAL 2-ARM PULLER拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL 2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET内提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBL Y FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜W ARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPL Y PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLL YE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶W ASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS 存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINA TION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER’S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE 固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY分类垃圾收集站WASTE-COLLECTION STATION CONTAINER立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扳手Wrenches/套筒Sockets开口扳手 Open End Wrenches梅花扳手 Spline End Wrenches块扳手 Crowfoot Wrenches开口/梅花扳手 Combination Wrenches内六角扳手 Hex Wrenches平板棘轮扳手 Slab Ratchet棘轮扳手 Ratchet Wrenches力矩扳手 Torque Wrenches管钳 Pipe Wrenches活动扳手 Adjustable Wrenches六角套筒 Six Point Sockets梅花套筒 Twelve Point Sockets万向套筒 Universal Sockets转接头 Adaptor套筒接杆 Socket Extension万向转接头 Universal Joint螺刀Screwdrivers快速螺刀 Fast Screwdrivers仪表螺刀 Electronic miniature Screwdrivers十字头螺刀 PILLIPS Screwdrivers磁性螺刀 Magnetic Screwdrivers一字头螺刀 Flat Tip Screwdrivers摇把 Speeders钳Pliers尖嘴钳 Needle Nose Pliers大力钳 Locking Pliers保险丝钳 Safety Wire Twisters鹰嘴钳 Adjustable Joint Pliers插头钳 Connector Plug剥线钳 Wire Strippers鱼口钳 Combination Slip-Joint Pliers卡环钳 Convertible Snap Ring Pliers剪线钳 Diagonal Cutters压线钳 Wire Crimpers电气工具Electronic Tools矿灯 Safety Lamb (Miner’s Lamb)手电 Flashing Light对讲机 Interphone电烙铁 Electronic Iron耳机 Earphone防静电手腕 Static Wrist电池 Battery充电器 Charger扬声器 Speaker电源插座 Receptacle电枪 Electronic Runner电钻 Electronic Drills指挥棒 Flashing Emergency Light超声波 Ultrasonic测量工具Measuring Tools钢板尺 Steel Rulers卷尺 Tape Rulers螺旋卡尺 Outside Micrometer塞尺 Feeler (Thickness) Gauges量杯 Measuring Cup游标卡尺 Dial Caliper表 Gauges三用表 Multi Meter兆欧表 Meg Ohm Meter杂项Diversiform反光镜 Inspection Mirror放大镜 Magnifier软杆双爪式机械手 Flexible Two_claw Pick Up Tool 软杆磁棒 Flexible Magnetic Pick Up Tool划刀 Utility Knife刮刀 Scraper Knife剪刀 Snip (Scissor)锯 Saw凿子 Chisels錾子 Punch三脚架 Tripod (Spider)铜榔头 Copper Hammer铁榔头 Iron Hammer胶榔头 Rubber Hammer弯勾 Hook锉 File镊子 Nipper (Pliers)销钉插拔工具 Pin Removal Tools 气枪 Pneumatic Runner气钻 Pneumatic Drills铆钉枪 Rivet Gun注射器 Injector (Squirt)滑油加油车 Oil Cart液压油加油车 Hydraulic Fluid Cart 注油枪 Grease Gun抹布 Dishcloth手套 Glove绳索 Rope工具箱 Tools Kit工具架 Tools Rack千斤顶 Jack撬棒 Tommy Bar工作梯 Work Ladder砂轮 Grinding wheel砂纸 Sand paper胶带 Adhesive Tape焊锡 Soldering Tin拖把 Tow Bar发光背心 Flashing Vest护目镜 Goggle (Blinkers)安全带 Life Belt(Safety Belt)。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
五金中英文对照门控五金专业术语Terminologies for door control hardware一、地弹簧 Floor hinge （ Floor spring）Adjustable creep speed 缓行速度Adjust detection sensibility 检测灵敏度调整Adjustment style 调速方式Two-section adjustment 两端调节Buffer 缓冲区Closing section 关门阶段Opening section 开门阶段Center pivoted arm 中心摇臂Top pivot seat 上枢轴座Pivot bottom seat 枢轴底座Offset pivot arm 偏心摇臂Closing force 紧闭力Closing speed 闭门运行速度Opening speed 开门运行速度Non-hold 无驻持Hold 驻持Economic model 经济型Floor hinge （ Floor spring）地弹簧Hydraulic control 液压控制Cover plate. 盖板Cam spindle 凸轮轴Sealing compound 密封化合物Environmental-Protection floor hinge 环保型地弹簧Insect prevention 防虫Water proof 防水Keep warm 保温Antirust 防锈Maximum opening angle 最大开启角度Maximum loading 最大门重Document number：NOCG-YUNOO-BUYTT-UU986-1986UTMaximum loading capacity 最大承重Maximum opening force 最大开门力Non-antomatic pivot hinge 地轴Pivot hinge 地轴Door axial 门轴Top pivot 顶轴Upper pivot 上轴Adjust gasket 调整垫片Bottom Pivot下轴二、玻璃门夹、驳接件、铰链类Bottom patch fitting 下夹Upper patch fitting 上夹Top patch fitting 顶夹Bending patch fitting 曲夹T patch fittingT形夹F patch fittingF 形夹Locker patch fitting 锁夹Lock case patch fitting 锁盒Long Patch fitting 长门夹Bottom patch fitting with lock 带锁下夹Bottom bracket 下驳接件Upper bracket上驳接件Top bracket 顶驳接件Bending bracket 曲形驳接件Z BracketZ形驳接件L bracket L形驳接件Glass door hinge 玻璃门铰链Opening angle 开启角度Arc precise-cast patch fitting 弧形精铸门夹Bending precise-cast patch fitting 曲形精铸门Heavy precise-cast patch fitting 重型精铸门夹Precise-cast patch fitting 精铸门夹系列三、门锁类 Door lock seriesFrameless door lock、Latch series 无框门锁、插销系列Frame door lock 、latch series 有框门锁、插销系列Profile door lock among 型材门中间锁Glass door lock 玻璃门锁Glass door latch 玻璃门插销Close device 地锁Latch 插销四、电锁类 Electric lock seriesControl center 管理中心Card reader 读卡器Protocol converter 协议转化器Power controler 电源控制器Electromagnetic lock 磁力锁Force 拉力Actuation current 启动电流Input voltage 输入电压Working current 工作电流Signal detection 侦测信号Electromagnetic lock for single-leaf door 单门磁力锁Electromagnetic lock for double-leaf door 双门磁力锁Lock body size 锁体尺寸Concealed Electromagnetic lock for single-leaf door 暗装式单门磁力锁Water-proof electromagnetic lock for single-leaf door 单门防水磁力锁Electric lock series 电插销系列Cutout voltage 断电Control signal 控制信号Electric bolt 电插销Shear lock 剪力锁Lock after power-off 断电上锁Shear 剪力Bracket 支架Electromagnetic door suck 电磁门吸Release after powe-off 断电释放Switch 开关Max. Current 最大电流Security level 安全标准Remote control 遥控器Remote operating range 遥控距离Card Capacity 卡容量Record Capacity 记录量Alarm function 报警功能Working Frequency 工作频率Automatic door drive 自动门机Microwave sensor微波感应器Controller 控制器Entension template 扩展模板Safety light 安全光线Spare battery 备用电池Motor 马达Credit card 刷卡器Semi-automatic door 半自动门机Guide rail length 导轨长度Sash width 门扇宽度Recommend bearing 推荐重量Top side installation 顶部安装Beside installation 侧面安装Applicable braket 适用支架Anti-jamming 抗干扰性能Automatic door drive system 自动门机Data storage 资料存储Detection area 检测区域Detection area adjustment 检测区域调整Detection method 检测模式Detection theory 检测原理Delay duration 保持延时Delay function 延时功能Density of transimission frequency 发射频率密度Device name 配件名称Door bell 门铃Door coordinator 顺位器Doppler 信息处理Electric bolt 电插锁Electromagnetic lock 电磁锁Electromagnetic lock for double-leaf door 双门磁力锁Electromagnetic lock for single-leaf door 单门磁力锁Extension template 扩展模块Lock in power off 断电关门锁Magnetism signal 门磁信号Microwave sensor 微波感应器Min. detection movement speed 最小检测运动速度Module of function 功能模块Motor 马达Multi-function extention module 多功能扩展模块Number of infrared beam 光束数Output watt 输出功率Power 电源Power controler 电源拉制器Programmed microcomputer 微电脑程序控制器Public code 公共密码Rate of transmission 传输速率Safety infrared beams 安全光线开关Sensor range 感应距离Signal detection 信号侦测Swipe card 刷卡Swipe card + code 刷卡+密码五、推拉移门类 Sliding door seriesAutomatic door drive 制动门机Automatic sliding door 自动平移门Automatic revolving door 自动旋转门Telescopic sliding door 伸缩推拉门Concealed sliding door 隐藏式推拉门Automatic sliding door operator 自动推拉门自动启闭装置Self monitoring radar motion detector自我监测雷达运动检测器六、拉手类 HandleStainless steel handle不锈钢拉手Round pipe handle 圆型执手Square pipe handle方型执手Special—sharped pipe handle异型执手Precision-cast door handle 精铸门拉手Precision-cast zinc alloy handle精铸锌合金拉手Precision-cast stainless steel handle精铸不锈钢拉手Single handle单支拉手Wooden handle木质拉手Marble handle大理石拉手卫浴产品术语Terminologies for Bathroom Hardware一、水龙头（Faucet）水龙头种类Cleaner Faucet 净身器龙头Concealed Faucet 暗式龙Double Handle Faucet 双把龙头Fast On Faucet 快开龙头Kitchen Faucet 厨房龙头Lavatory Faucet 脸盆龙头Pedaled Faucet 脚踏式龙头Shower Faucet 淋浴龙头Shower Nozzle 淋浴喷头水龙头配件Angle Valve 角阀Cold-water tap 水嘴Shower mixer 淋浴水龙头faucet, mixer tap 明三联式浴缸水嘴shower 淋浴喷头shower curtain 浴盆帘Lever handle 一字型把手Cross handle 十字把手Handle assembly 把手组件二、化妆镜（Cosmetic Mirror）安装情况bathroom cabinet 卫生间镜箱round front model 圆形设计oval shape design 椭圆形设计countertop installation 圆台面上安装fixing with back to wall 背靠墙式安装above counter mounting 台上安装under counter mounting 台下安装fixing above table board 柜上安装玻璃门合页（Glass Door Hinge）三、卫浴配件（Bathroom accessory）挂式配件Fix Clamp 固定夹Support Bar 浴室支撑杆Glass Clamp玻璃夹Connector连接件Mounting 固定座Rail Connecting Block 导轨支撑件 Handle 拉手Robber Hook 衣钩towel ring毛巾环其他配件Position Block 限位器Wheel 导轮Guide Rail 导轨Mounting 固定座Guide track 导槽Mounting Bracket 支撑脚Mount Header Bracket 吊码Hinge 合页Header Corner 角码四、马桶（toilet）按种类分urinal小便器相关配件toilet, lavatory 恭桶。