《互换性与技术测量》之表面粗糙度
合集下载
相关主题
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
The surface is treated by removing the material. 用去除表层金属方法获得
The surface is obtained without removing the material. 用不去除表层金属的方法获得
请点击鼠标左键显示后面内容
(2)The location for specifying the surface finishes and related symbols 表面粗糙度数值及有关规定在符号中注写的位置
+ (Ymax 谷 1+ Ymax 谷 2 + Ymax 谷 3+ Ymax 谷 4 + Ymax 谷 5)/5
3 Maximum contour height Ry 轮廓最大高度Ry Ry is defined as the distance within the sample length from the peak line to the bottom line. Ry是在取样长度内,轮廓峰顶线和轮廓谷底线之间 的距离。
4 Surface Finishes 表面粗糙度
Surface finishes 表面粗糙度概念 Evaluation parameters for surface finishes 表面粗糙度评定参数 Symbols of surface finishes 表面粗糙度的符号 Marking the finishes 表面粗糙度在图样中的标注 Selecting the finishes value 表面粗糙度数值的选用 Exercises 练习题
(2)形状误差 :零件表面中峰谷的波长和波高之比大于 1000的 不平程度属于形状误差,无明显的周期性变化,波距在10mm 以上。 (3)表面粗糙度:零件表面所具有的微小峰谷的不平程度,大 体呈周期性变化,其波长和波高之比一般小于 50,波距小于 1mm。属于微观几何形状误差。
Surface Finishes 表面粗糙度概念
请点击鼠标左键显示后面内容
Marking the finishes 表面粗糙度在图样中的标注
1) In the same drawing, one be surface isthe only marked once with related 3) symbol should moveable or revolvable inmost accordance 2) If Roughness 4) 5) The If there various tip are of surfaces various roughness requirements require symbol the should same on roughness, point same to surface, the the surface fine from solid common line symbol (code). should be marked oncontours. contours, dimension lines, with positionto variation, but shouldn’t be turned over orrelated be distorted. The is required outside symbols and can represent should beItmarked touch their on boundary the the surface topright lines, corner and and with symbol ‘The (code) rest’. dimension boundaries or their extension linesas and should be as number size of roughness value should be the same that of and close dimension should be shown. asItpossible to related dimension lines. with roughness 粗糙度符号的尖端必须从材料外指向零件表面,并与表面轮廓接触上。 dimensions. is moveable or revolvable in accordance 多个表面具有相同粗糙度要求时,对其中使用最多的一种代(符)号, 在同一图样中 , 每一表面一般只标注一次粗糙度代(符)号 , 应注在可见 symbol and is in accordance with its dimension direction. 可以统一标注在图纸的右上角,并加注“其余”字样。 一表面上有不同要求时,需用细实线画出其分界线,并标注相应粗糙度代
The microscopic geometrical property formed by the small clearance and the rise and fall on the machined surface is called surface finishes.
零件加工表面上具有的较小间距和峰谷所形成的微观几 何形状特性称为表面粗糙度。
请点击相应标题显示其内容
4.1 Introduction 1. The concept of surface finish
• 1)surface luction :λ from 1 to 10 mm
•
表面波纹度
• 2)macro-figure error is figure error : λ>10 mm
请点击鼠标左键显示后面内容
2. Surface finish affect the function of works
(1) surface finish affect wearability (耐磨性): surface finish↑ → friction ↑ → wearability ↓ but surface finish↓ → wearability ↓↓ (2) surface finish affect rigidity (接触刚度): surface finish↑→ S ↓ → deformation(变形) ↑ → rigidity ↓ (3) surface finish affect fit : surface finish↑ → the clearance of clearance fit ↑ surface finish↑ → the interference of interference fit ↓ surface finish↑ → the clearance of transition fit ↑ the interference of cross fit ↓ (4) surface finish affect fatigure strength(疲劳强度) : surface finish↑ → stress focus on ↑ →fatigure strength ↓ (5) surface finish↑ → corrosion (耐腐蚀性)by gases or liquid ↑
若全部表面的粗糙 度相同,则可直接 在图的右上角注明
国外图例
0.8
请点击鼠标左键显示后面内容
4.5 Selecting the finishes value 表面粗糙度数值的选用
(1)Ra values and their corresponding machining methods 表面粗糙度的表面特征及其经济加工方法
Ra/µ m Microcosmic surface features 表面微观特征
50 25 Obviously visible tool marks明显见刀痕 Visible tool marks可见刀痕 Occasional tool marks微见刀痕 Visible machining marks可见加工痕迹 Occasional machining marks微见加工痕迹 Invisible machining marks看不见加工痕迹 Recognizable machining veins 可辨加工痕迹方向 Occasional machining veins微辨加工痕迹方向 Invisible machining veins不辨加工痕迹方向
4.3 Evaluation parameters for surface finishes
表面粗糙度评定参数
1Contour arithmetic mean deviation Ra 轮廓算术平均偏差Ra Ra is the absolute arithmetic mean of contour deviated distance (distance between each point of the contour surface and the base line) within a sample range of the part surface. Ra是在零件表面的一段取样长度内,轮廓偏 距y(表面轮廓上点至基准线Ox的距离)的绝对值的算术平均值。
a e b c/f d
图片
a: Code and value of finishes height (unit: µ m); Ra的最大允许值,若写 为a1/a2则为最大允许值/最小允许值; Ra字母可省,若是Rz或Ry时, 应在数值前注明Rz或Ry(单位:m)。 b: Machining requirements, plating, coating, surface treatment, or other requirements.加工方法代号(如:车、铣、镀涂或其他表面处理等) c: Sample length(unit: mm)or waves (unit: µ m);取样长度(单位:mm)。 d: Symbol of machining veins; 加工纹理方向符号(如: M等)。 e: Allowance(unit: mm) ;加工余量(单位:mm)。 f: Clearance value of finishes (unit: mm) or contour supporting length rate. 粗糙度间距参数值(单位:mm)或轮廓支承长度率。
Ra =1/L
Y
|Y(x) | dx 1/n | Yi |
0
1
n
i 1
Yi
Ra
X
0
L
请点击鼠标左键显示后面内容
Yn
Evaluation parameters for surface finishes
表面粗糙度评定参数
2 Ten-point height average Rz 微观不平度十点高度Rz Rz is defined as the sum of average of 5 contour peak heights and the average of 5 contour bottom depths. Rz是在取样长度内,5个最大轮廓 峰高的平均值与5个最大轮廓谷深的平均值之和。 Rz= (Ymax 峰 1+ Ymax 峰 2 + Ymax 峰 3+ Ymax 峰 4 + Ymax 峰 5)/5
•
宏观几何形状误差(几何形状误差)
• 3)micro-figure error is surface finish : λ <1mmwk.baidu.com
• •
微观几何形状误差(表面粗糙度)
(1)表面波纹度:零件表面中峰谷的波长和波高之比等于 50~ 1000的不平程度称为波纹度,呈周期性变化,波距在1~10mm 之间。会引起零件运转时的振动、噪声,特别是对旋转零件 (如轴承)的影响是相当大,目前表面波纹度还没有制定国家 标准。
轮廓线、尺寸线、尺寸界线或它们的延长线上, 并尽可能靠近有关尺寸线。 粗糙度符号可随加工表面的位置不同平移或旋转,但不能翻转和变形; (符)号和尺寸。 粗糙度数值中数字的大小应与同一图样的尺寸数字一致,可随粗糙度符号旋 转而旋转,但应与该处尺寸标注的方向一致。
0.8
1.6
6.3 6.3
其余
12.5
Rz3.2
Y
Ry = Y 峰 max + Y 谷 max
Ry
Rz
X
0
L
请点击鼠标左键显示后面内容
4.4 Symbols of surface finishes 表面粗糙度的符号 (1)The surface finishes symbol 表面粗糙度的符号
2H
H
60°
60°
Basic symbol 基本符号