SP101E_RF-11键控制器

SP101E无线遥控控制器使用说明
一、特点：
1、RF射频无线控制，距离可达15M，操作灵敏人性化，接线简单方便；
2、支持定制市面上常见的单线或双线的LED驱动IC；
3、自带125种花样效果，炫丽灵动；
4、最多可带多达2450个像素点；
5、电源具有防反接功能。

二、遥控器部分
1、按键功能：
ON/OFF控制灯具亮灭NUM+增加每一段的点数
MODE+向前选择花样效果NUM-减少每一段的点数
MODE-向后选择花样效果SEC+增加分段数
SPEED+加快效果的跑动速度SEC-减少分段数
SPEED-减慢效果的跑动速度MATCH遥控器与接收器配对
AUTO自动循环跑全部花样效果
2、灯具测试功能和配对：
连续按AUTO键4-6次直到灯具熄灭，放开AUTO键，跳转到红、绿、蓝、黄、紫、青、白七色跳变效果，方便灯具测试；连续按MATCH键4-6次可以与接收控制器进行一对一配对，配对后其它控制器不能对该接收控制器进行操作，连续按MATCH 键4-6次可以与接收控制器解绑，此时该控制器可以接受其它遥控器控制命令。

默认出厂时是一对多模式。

3、分段：
有些花样效果设置成了分段跑动，每一段的跑动的效果是一样的。

若是整体跑动的效果段，同样可以选择分段数，和每段的点数。

段数可选：5、10、15、20、25、30、35；每段点数可选：20、30、40、50、60、70。

总点数=段数x每段的点数
4、掉电保存：
本控制器会把用户的每一次按键设置自动保存下来，断电后，下次上时电控制器会按原来设置跑动，避免断电后要重新设置的麻烦。

三、接收部分
支持定制市面上常见的单线或双线的LED驱动IC；用户可以在发货前说明要用于支持哪种IC，我们设置好后发货，也可以后面自行修改PCB板子上的R5,R6,R7,R8四个电阻的短接或断开状态来选择支持哪种IC：
修改动作改动后支持IC
不短接R5，R6，R7，R8任何电阻WS2811
短接R5，断开R6，R7，R8WS2801
短接R6，断开R5，R7，R8LPD6803
短接R7，断开R5，R6，R8LPD8806
短接R8，断开R5，R6，R7UCS9812
短接R5，R6，断开R7，R8UCS1903，APA104
短接R6，R7，断开R5，R8APA102
短接R7，R8，断开R5，R6TM1804，TM1809
本产品可选择5V供电和12V两种供电电压。

注意：上电前请确认供电电压。

四、应用接线图
SP101E Wireless controller operating instructions
1.Features:
1.RF Remote control,with long distance,wire connection is simple and very easy to use;
2.Support almost every kind of one-wire or two-wire LED-DRIVER-IC;(Can be customized)
3.With125kinds of patterns,which are vivid and beautiful;
4.Each controller can control up to2450pixels;
5.Preventing reverse connection of power supply.
2.Remote Control
1.Functions Of Each Button:
ON/OFF ON or OFF
MODE+Switching patterns forwardly
MODE-Switching patterns backwardly
SPEED+Switching speed forwardly
SPEED-Switching speed backwardly
AUTO Run internal patterns automatically
NUM+Add the number of pixels on each section
NUM-Decreased the number of pixels on each section
SEC+Add number of section.
SEC-Decreased number of section.
MATCH Match the Remote control with the receiving controller
2.Testing and Matching:
Pressing the AUTO button for up to4times until LED is out,release the AUTO button to into the mode of switching in red,green,blue,yellow,purple,cyan and white,witch to test the your LED.
Pressing the MATCH button for up to4times to match the Remote control with the receiving controller.Pressing the MATCH button for up to4times to un-match.
3.Sections:
Some of the patterns run in several sections,each section is the er can make the number of sections as follow:5,10,15, 20,25,30,35.Pixel number of each section can be chosen as follow:20,30,40,50,60,70.
Sum of pixels=Sections*Number per section
er Setting Saving:
User’s each pressing on the button can be saved by the controller automatically.When the controller is power off,next time power up,it will work the way as the same as before.
3.Receiving Controller：
Can be customized to support almost every kind of one-wire or two-wire er can specify to support which IC before our delivery,and also,user can modify the status of R5,R6,R7,R8on the PCB to meet their needs:
Actions To support IC
Short none of R5,R6,R7,R8WS2811
Short R5,breakR6,R7,R8WS2801
Short R6,breakR5,R7,R8LPD6803
Short R7,breakR5,R6,R8LPD8806
Short R8,breakR5,R6,R7UCS9812
Short R5,R6,breakR7,R8UCS1903,APA104
Short R6,R7,breakR5,R8APA102
Short R7,R8,breakR5,R6TM1804,TM1809
The receiver controller has two kinds of working voltage:5V-supply-voltage and12V-supply-voltage.
Cautions:Please make sure the power supply voltage is match to your controller before you power it.
4.Wire Connection：。