S150JA说明书
1300A使用说明书[详细讲解]
![1300A使用说明书[详细讲解]](https://img.taocdn.com/s3/m/ea899cb50129bd64783e0912a216147917117e22.png)
目录1、产品简介2、产品特点3、应用范围4、型号意义5、结构说明6、产品安装7、运转前的准备工作8、试运转及正常操作9、特别注意事项10、设备维护和保养11、机组日常检查项目12、电路图13、电器元件清单14、机组使用说明书1、产品简介:BYWC系列一体化水冷式冷水机组是我公司自行设计制造的一种新型制冷产品。
其技术先进、品质优良、安全可靠、系统性强。
具有风冷机组的结构水冷机组的效率，填补了中央空调产品线的空白，为用户提供了安装使用简单、方便、可靠中央空调产品。
2、产品特点:2.1 本系列产品是我公司的国家专利技术产品,它将冷站机房、冷水机组、冷却器、冷冻水泵、冷却水泵及配套管道设备和控制元件(检测仪表及断水保护器等)安装在同一基座上集成为一整体装置。
可直接安装于楼顶、室外等空旷场所不需任何防护外壳。
2.2采用国际名牌螺杆压缩机,质量可靠、效率高。
2.3比现有风冷冷水机组能效比高,更省电、寿命更长。
2.4配有远控箱,可在200米范围内对机组进行开、停机操作。
2.5 控制电器选用国际品牌产品，确保产品可靠性。
3、应用范围:本系列产品适用于宾馆、商场、办公楼、实验室、文娱场所、医院、影院、工厂、工艺冷源、多室家庭、豪华别墅等楼堂馆所需要空调的环境,也适用于改造工程,局部空调工程之需要,不需要专门机房,设计快捷、安装方便、投入应用周期极短。
4、型号意义：R22：代表制冷剂为134A：代表低温机组（常温不标）(KW)5、结构说明:正面示意图：在正面右边有一扇检修门,打开后可进行以下工作：可观测机组的高压及低压压力。
右下方有加氟阀，可进行机组的加氟操作右面示意图：机房右侧有检修门,打开进入可作机组维护、检修、检查工作；门内左侧有照明控制开关；左面示意图：左侧有一扇操作门。
打开该门,上方有机组电控箱，可进行机组的开停机等操作;右边电控箱上有一旋钮, 分别是（“冷”、“泵”两位置)；设置机组的制冷运行选“冷”位置；设置机组的冷冻水管道清洗选“泵”位置。
SINAMICS S150 产品说明书
Answers for industry./sinamics-s150SINAMICS S150The Drive Solution for Sophisticated High-Rating Single Motor Drives*Exception: V20 – does not require a selection and configuration tool; G180 is commissioned using the IMS software (Inverter Management Software)2SINAMICS – the optimum drive for each and every applicationThe drive family for drive solutions that are fit for the futureThe SINAMICS family offers the optimum drive for each and every drive application – and all of the drives can be engineered, parameterized, commissioned and operated in a standard fashion.SINAMICS –fit for every application•Wide range of power ratings from 0.12 kW to 120 MW•Available in low-voltage and medium- voltage versions•Standard functionality using a common hardware and software platform •All of the drives can be engineered using just two tools: SIZER – for engineeringSTARTER – for parameterizing and commissioning•High degree of flexibility and combinability3High precision and dynamic response SINAMICS S150 cabinet units are espe-cially suited for variable-speed, single-axis drives with high demands placed on the performance, i.e. drives with •High requirements regarding the dynamic performance•Frequent braking cycles with high-braking energies•Four-quadrant operation•SINAMICS S150 offers high-perfor-mance closed-loop speed control with •high precision and dynamic response.Reliable solution for many applications Variable-speed drives for high-perform- ance process operations are especially applicable for machinery and plant construction in the process and produc- tion industries: Food and beverage, auto- mobile and steel industries, underground/ open-cast mining, marine engineering and cranes/conveyor technology profitCompetitive advantages for plant and machine buildersThe self-commutated, pulsed infeed/regenerative feedback units employing IGBT technology in conjunction with a Clean Power filter guarantee an extraor-dinary line-friendly behavior, which sets itself apart as a result the following properties:•Negligible line harmonics as a result of the innovative Clean Power filter (<< 1 %)•The stringent limit values laid down in IEEE 519-1992 are maintained without any exceptions •Energy recovery(four-quadrant operation)•Tolerant with respect to line voltage fluctuations•Operation on weak line supplies•Reactive power compensation is pos-sible (inductive or capacitive) •High drive dynamic performance Simple drive handling – from engineering through to operation as a result of the •Compact and modular design withoptimum service friendliness •Straightforward engineering•Simple installation, as the units are ready to be connected•Fast, menu-prompted commissioning without complex parameterization Significantly reduced:Space requirement and noise level The SINAMICS S150 drive converter in a standard cabinet is especially quiet and compact because of its state-of-the-art IGBT power semiconductors togetherwith an innovative cooling concept.The new drive qualitySINAMICS S150 drive converter4Consequentially line-friendlyBy impressing almost sinusoidal line currents, the har- monic losses known from conventional drive converters in the line transformer, low-voltage distribution and line feeder cables are avoided. Further, SINAMICS S150 does not cause any basic fundamental reactive power. This is because the line power supply factor cos φ is 1 independent of the load. However, SINAMICS S150 has an especially interesting positive feature as it can feed inductive or capacitive reactive current into the line supply over wide limits. This allows loads caus- ing reactive power that are operating in parallel to be compensated, thus reducing expensive reactive power drawn from the public utility company.As standard, SINAMICS S150 is supplied with anintegrated EMC filter for the second environment (C3) according to EN 61800-3. This means that the drive converter doesn’t result in any inadmissible noise even in the high-frequency range.SINAMICS S150 – precision drive withenergy-saving and line-friendly technologyTo efficiently use energyFor applications where the associated drives operate regeneratively as a result of frequent braking cycles and with high energy levels when braking, then it makes a lot of economic sense to regenerate this energy into the line supply. This is significantly more cost-effective than to convert the energy into heat, for example, using a braking chopper. SINAMICS S150 offers the best prerequisites because not only is it capable of regenerative feedback without any restric- tions, but it does this with the highest precision and dynamic response.5Precision and force for every productionThe optimized inverter functionality of the SINAMICS S150 allows high-precision closed-loop speed and torque control with and without an encoder. Further, the DC link voltage of the SINAMICS S150 is controlled to maintain it at a constant level.This decouples the motor from the effects of the line supply voltage. This means that the highest machine precision is guaranteed, even when the drive system is connected to weak line supplies. This makes this drive the ideal solution, for example, for test stands, centrifuges, elevators, crosscutters,shears, conveyor belts, presses and cable winches.Completely seamless:Totally Integrated AutomationHigh precision and fast processes profit because the intelligence has been shifted into the drive – even for large drives! This is because as the degree of automation increases, then it is essential that the drive system is integrated into the higher- level automation environment. It goes without saying that SINAMICS S150 is part of Totally Integrated Automation (TIA), the unique, common automation platform from Siemens. Totally Integrated Automation sets standards regarding integrated engineering, data manage- ment and communications.6SIZER –minimizes engineering costsThe SIZER for Siemens Drives engineering software decisively simplifies the engi-neering of low-voltage drive systems: Starting from your application, the tool supports you step-by-step when defining the mechanical system as well as when selecting and dimensioning converters, motors and gear units. The tool also allows additional system components to be configured along with the open-loop/closed-loop control.The new level of simplicityPlanning, commissioning and operator control the easy wayDigital DRIVE CLiQ interface: Simply connect up!Seamless communications between the various components is a prerequisite for a modular drive system. The standard digital interface is known as DRIVE CLiQ and connects, as serial interface, the components in the cabinet and the motors.STARTER –speeds up commissioningThe STARTER commissioning tool sup-ports you when parameterizing, com-missioning, troubleshooting and when service is required. A real highlight:Using STARTER, you can import all of the relevant data from the electronic type plates of the drive components. This speeds up parameterization, helps avoid possible incorrect entries and therefore significantly reduces your costs. You can check your parameterization and auto-matically optimize it using the integrated test functions. Setpoints and actual values can be traced and displayed in the and frequency domains. Further, STARTER offers a graphic configuring interface. This provides a good over-view, simple handling and allows safety acceptance reports to be automatically generated.accessibility so that parts and compo- nents can be quickly replaced. This means the highest degree of service friendliness but at the same time an extremely small footprint.1) R ated power of a typical 6-pole standard induction motor based on IL for 3-ph. 500 or 690 V AC,50 Hz.2) T he cabinet height is increased by 250 mm for degree of protection IP21, by 400 mm for degree ofprotection IP23, IP43, IP54 and by 405 mm for the options for line or motor connection from the top.7Follow us on:/siemensindustry /siemensThe information provided in this brochure contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of furtherdevelopment of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners.Siemens AG Industry Sector Large Drives P.O. Box 474390327 NUREMBERG GERMANY Subject to change without prior notice Order No.: E20001-A140-P570-V2-7600 DISPO 21503GD.LD.XX.SISX.52.2.01 WS 10113. Printed in Germany © Siemens AG 2013。
S150,S300系列纯正波变压器用户手册说明书
S150,S300 Series Pure Sine Wave Inverter User’s ManualList of contents1. Important Safety Instructions (3)1-1 General Safety Precautions (3)1-2 Precautions When Working With Batteries (3)2. Features (4)2-1 Electrical Performance 150W (4)2-2 Electrical Performance 300W (5)2-3 Mechanical Drawings 150W (6)2-4 Mechanical Drawings 300W (7)3. Introduction (8)3-1 Front Panel Operations (8)3-2 Rear Panel Operations (8)3-3 AC Safety Grounding (9)3-4 Installation (10)3-5 DC Input (Outlet sockets available) (11)3-6 AC output (Outlet sockets available) (11)4. Troubleshooting guide (12)5. Maintenance (13)6. Warranty (13)1. Important Safety Instructions1-1. General Safety Precautions1-1-1. Do not expose the Inverter to rain, snow, spray, bilge or dust.To reduce risk of hazard, do not obstruct the ventilationopenings. Do not install the Inverter in a zero-clearancecompartment. Overheating may result.1-1-2. To avoid a risk of fire and electric shock. Make sure that existing wiring is in good electrical conditions and the size is not undersized.Do not operate the Inverter with damaged or substandard wiring.1-1-3. This equipment contains components which can produce arcs or sparks. To prevent fire or explosion, do not install in compartmentscontaining batteries or Flammable materials or in locations whichrequire ignition protected equipment. This includes any spacecontaining gasoline-powered machinery, fuel tanks, or joints, fittings,or other connection between components of the fuel system.1-2. Precautions When Working with Batteries1-2-1. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with runningcold water for at least 20 minutes and get medical attentionimmediately.1-2-2. Never smoke or allow a spark or flame in vicinity of battery or Engine.1-2-3. Do not drop a metal tool on the battery. The resulting spark or short-circuit on the battery of other electrical part may cause anexplosion.1-2-4. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery.A lead-acid battery can produces a short-circuit current high enoughto weld a ring or the like to metal, causing severe burns.2.Features2-1. Electrical Performance 150WSpecification Model No.Item S150-112 S150-124 S150-212 S150-224 Continuous OutputPower150WSurge Rating 200WInput Voltage 12V 24V 12V 24V Input Voltage Range 10.5 – 15.0 21.0 – 30.0 10.5 – 15.0 21.0 – 30.0 Output Voltage 110 VAC ±5% 230 VAC ±5%Frequency 50 / 60Hz ± 0.3%Max. Efficiency 87% 88% 87% 88% No Load Current Draw 0.20A 0.16A 0.22A 0.16A Output Waveform Pure Sine Wave ( THD 5.0% Typical )Power Factor Allowed cosθ-90° ~ cosθ+90°Protection Overload, Short Circuit, Reverse Polarity (Fuse), Over / Under Input Voltage, Over Temperature.Remote Control Yes, On/Off controlled by external switch Safety UL458 EN60950EMC FCC Class B EN55022：1997EN61000-3-2：1998EN61000-3-3：1995EN55024：2001e-Marke13-022025Operating Temperature 0 – 40 ℃Storage Temperature -30℃ to 70℃Fan Cooling Thermostatically controlled Dimensions (L x W x H) 200 x 132 x 72 mm / 7.87 x 5.20 x 2.83 inch Weight 2.7 kgs. / 5.4 Lbs.2-2. Electrical Performance 300WSpecification Model No.Item S300-112 S300-124 S300-212 S300-224 Continuous OutputPower300WSurge Rating 400WInput Voltage 12V 24V 12V 24VInput Voltage Range 10.5 – 15.0 21.0 – 30.0 10.5 – 15.0 21.0 – 30.0 Output Voltage 110 VAC ±5% 230 VAC ±5%Frequency 50 / 60Hz ± 0.3%Max. Efficiency 89% 89% 89% 89%No Load Current Draw 0.24A 0.28A 0.26A 0.28A Output Waveform Pure Sine Wave ( THD 5% Typical )Power Factor Allowed cosθ-90° ~ cosθ+90°Protection Overload, Short Circuit, Reverse Polarity (Fuse), Over / Under Input Voltage, Over Temperature.Remote Control Yes, On/Off controlled by external switch Safety UL458 EN60950EMC FCC Class B EN55022：1997EN61000-3-2：1998EN61000-3-3：1995EN55024：2001e-Marke13-022078Operating Temperature 0 – 40 ℃Storage Temperature -30℃ to 70℃Fan Cooling Thermostatically controlled Dimensions (L x W x H) 237 x 155 x 72 mm / 9.33 x 6.10 x 2.83 inch Weight 3.5 kgs. / 7.7 Lbs.2-3. Mechanical Drawing2-4. Mechanical Drawing3. IntroductionThis series models are the most, reliable, multi protections, compact size, puresine wave inverters that used in wide range of applications including Mobile, Officeequipments, Home entertainments, electronics hold equipments.To get the most out of the power inverter, it must be installed and usedproperly. Please read the instructions in this manual before installationand operation this model.3-1. Front Panel Operations：3-1-1. ON / OFF/ REMOTE switch：Leave the Power ON / OFF / REMOTE switch in the OFF positionduring installation.3-1-2 LED display indicates Power StatusStatusLED ConditionsSolid Green AC Power OKBlinked Red fast OVPBlinked Red slowly UVPBlinked Red intermittently OTPSolid Red OLP3-1-3. Remote Port: Placing 0.75mm2 and Screw type cable betweenremote port and panel.3-2. Rear Panel Operations3-2-1. Ventilation window: Do not obstruct, allow at least 3 inch ofclearance for airflow.3-2-2. Input terminals：Connect 12V / 24V batteries or other 12V / 24V powersources. 【＋】is positive,【－】is negative.Reverse polarity connection will blow internal fuseand may damage inverter permanently.3-2-3. Using # 8 AWG wire to connects Chassis ground with Vehicle Chassis.3-3. AC Safety Grounding：During the AC wiring installation, AC input and output ground wires areconnected to the inverter. The AC input ground wire must connect to the incoming ground of your AC utility source.The AC output ground wire should go to the grounding point for your loads ( for example, a distribution panel ground bus ).3-3-1. Neutral Grounding (GFCI’S)：110V models：The neutral conductor of the AC output circuit of theInverter is automatically connected to the safety ground during inverteroperation. This conforms to National Electrical Code requirementsthat separately derived AC sources (such as inverter and generators)have their neutral conductors tied to ground in the same way that theneutral conductor from the utility is tied to ground at the AC breakerpanel. For models configured with a transfer relay, while AC utilitypower is presenting and the Inverter is in bypass mode, this connection(neutral of the Inverter’s AC output to input safety ground) is not presentso that the utility neutral is only connected to ground at your breakerpanel, as required. Cotek has tested the following GFCI – protected20A receptacles and found that they functioned properly whenconnected to the output of the Inverter3-4. InstallationBefore connect your applications to the inverter, always check the power draw of your appliances. The inverter is affordable to supply surge power for a short time so as to start up the electrical equipments such as motor, pumps…that need more power while starting up.When all the above requirements are checked OK and satisfied and allconnections are made, it’s the time to turn on your inverter by pushing thepower switch to the ‘ I ’ position. The sine wave shaped output voltagegently rises from AC outlet.When the inverter is not supplying power to an application for a longer time, it’s recommended to turn off the inverter to save your batteries since it stilldraws a small amount of current in the “ no load ” condition.DC input voltage status as follows:DC Input Over Voltage DC Input UnderVoltageModelShut-down Restart Shut-down Restart 12Vmodels15.3 14.8 10.5 12.5 24Vmodels30.6 29.6 21.0 25.03-5. DC Input (Outlet sockets available)：CIGARET CLAMP TERMINAL3-6. AC output (Outlet sockets available)：Australia / New Zealand4. Troubleshooting guide：Problems and Symptoms Possible Cause Solutions No output voltage, the LED glows RED light.a. Power status light isblinked red fast. Over input voltage. Check input voltage.Reduce input voltage.b. Power status light isblinked red slowly. Low input voltage. Recharge battery.Check connectionsand cable.c. Power status light isblinked redIntermittently. Thermal shutdown Improve ventilation.Make sure ventilationopenings in inverterare not obstructed.Reduce ambienttemperature.d. Power status light is glowed red steadily. Short circuit, Wiringerror,Over LoadCheck AC wiringfor short circuit.Remove load.5. Maintenance：Very little maintenance is required to keep your inverter operating properly.You should clean the exterior of the unit periodically with a damp cloth toprevent accumulation of dust and dirt.At the same time, tighten the screws on the DC input terminals.6. Warranty：We warrant this product against defects in materials and workmanship for a period of 24 months from the date of purchase and will repair or replace any defective Power Inverter when directly returned, postage paid, to us.This warranty will be considered void if the unit has suffered any obviousphysical damage or alteration either internally or externally and does notcover damage arising from improper use such as plugging.The unit into an unsuitable power sources attempts to operate products with excessive power consumption requirements, or use in unsuitable environments.This is the only warranty that the company makes.No other warranties express or imply including warranties of merchantability and fitness for a particular purpose.Repair and replacement are your sole remedies and the company shall not be liable for damages, whether direct, incidental, special or consequential, even though caused by negligence or other fault.。
产品说明书_CN_多功能频有源专业扬声器系统_全U-Meline S15-2018
CN产品说明书S15多功能频有源专业扬声器系统全U M -M e l i n e S 15-20180403 v e r A感谢您购买 产品！请仔细阅读本手册，它将帮助你妥善设置并运行您的系统，使其发挥卓越的性能。
并保留这些说明以供日后参照。
警告：为了降低火灾与电击的风险，请不要将产品暴露在雨中或潮湿环境中。
警告：为了降低电击的风险，非专业人士请勿擅自拆卸该系统。
仅供专业人士操作。
等边三角形中的闪电标记，用以警示用户该部件为非绝缘体，系统内部存在着电压危险，电压。
可能足以引起触电。
可能足以引起触电如系统标有带惊叹号的等边三角形，则是为提示用户严格遵守本用户指南中的操作与维护规定。
注意：请勿对系统或附件作擅自的改装。
未经授权擅自改装将造成安全隐患。
警告：燃不得将明火源(如点的蜡烛)放在器材上面。
1. 请先阅读本说明。
2. 保留这些说明以供日后参照。
3. 注意所有警告信息。
4. 遵守各项操作指示。
5. 不要在雨水中或潮湿环境中使用本产品。
6. 不要将产品靠近热源安装，例如暖气管、加热器、火炉或其它能产生热量的装置（包括功放机 ）。
7. 不要破坏极性或接地插头的安全性设置。
如果提供的插头不能插入插座，则应当请专业人员更换插座。
8. 保护好电源线和信号线，不要在上面踩踏或拧在一起（尤其是插头插座及穿出机体以外的部分 ）。
9. 使用厂商规定及符合当地安全标准的附件。
10.雷电或长时间不使用时请断电以防止损坏产品。
12. 不要让物体或液体落入产品内——它们可能引起火灾或触电。
13. 请注意产品外罩上的相关安全标志。
. 仅与厂商指定或与电器一同售出的推车、架子、三脚架、支架或桌子一起使用。
推动小车/电器时，应谨防翻倒。
11注意事项产品的安装调试须由专业人士操作。
在使用非本厂规定的吊装件时，要保证结构的强度并符合当地的安全规范。
警告：1扬声器及扬声器系统的产品有限保修期为自正式购买日起的3年。
由于用户不合理的应用而导致音圈烧毁或纸盆损坏等故障，不包含于产品保修项目。
佳木斯EBZ150A掘进机电气说明书
⒌安全标志 生产许可证： 操作箱防爆合格证：1072197 操作箱煤安标志号：200702826 操作箱防爆标志：ExdⅠ 开关箱防爆合格证：10621428 开关箱煤安标志号：200702031 开关箱防爆标志：Exd〔ib〕Ⅰ
掘进机用（或矿用） 额定电压（V） 额定功率（W） 设计序号 隔爆型 操作箱
警示语
1． 开关箱所有关联设备必须符合本开关箱控制元件参数要求，用 户不得更改开关箱、关联设备的结构及电气参数。
2． 使用时应避免淋水。 3． 未经培训人员不得操作和维护本机。 4． 定期检查各负载电缆是否磨损。 5． 电缆引入装置的密封胶圈、金属垫圈、压板不得缺损。 6． 在维护和使用中，不得改变本安电路的元器件的型号和参数。 7． 安标控制元件必须具有安全标志证书且在有效期内。 8． 必须定期检查整个电气系统，不得带故障运行。 9. 在维修、维护时严禁带电开盖！严禁损伤隔爆面。
3.2. 油泵电动机M1：掘进机用隔爆型三相异步电动机，型号：YBU-75，额定电压：
AC1140V/660V，额定电流： 47A/82A.，绝缘等级：H级。冷却方式：风冷（IC411）
3.3. 二运输电机M3：为隔爆型油冷式电滚筒，型号：BYD11-160-8050，额定电压：
AC1140V/660V，额定电流：8.2A/14.2A。
由关联设备KXJ4-236/1140（660）E开关箱供电，配套本安电源：为本安型，型号： DXJ-18 本安输出最高开路电压： DC19.8V 本安输出最大电流：680mA
3.8. 操作箱：为隔爆型，型号：CXB4-10/24E，额定电压：DC24V，额定功率：<10W。 3.9. 开关箱：为隔爆兼本质安全型，型号：KXJ4-236/1140（660）E，额定电压：
自动洗板机使用说明书
用户安全提示请您在仪器使用之前，仔细阅读本《使用说明书》后再进行仪器的使用。
表示保护接地端子。
任何人不许拆卸、更换，否则有可能出现触电或火灾，不要进行用户手册描述的维护操作以外的任何操作。
确认采用了指定电源,若采用非指定电源，可能会出现火灾或触电。
应该采用独立电源。
如果和其他电器设备同用一个电源插座，在插座处会格外热，容易引发火灾。
拔下插头时，不应拉电源线,应该用手指支撑着插头把它拔下来，否则，可能会触电或短路引发火灾。
不要用湿手插拔电源,可能会触电。
不要损坏电线和连接电缆等，不要踩踏、扭曲、拉扯电线和电缆，如果电线和电缆折断会发生触电或引发火灾。
不要用已经损坏的电线和连接电缆等，可能会发生触电、或引发火灾。
不要用设计要求以外的其他电线和电缆，如果电容量小，会引发火灾。
有异常动作时，应立即停止操作。
当感觉到有烧焦味或异味等，异常错误时，立刻关掉电源，拔下电源线。
必须使用有良好接地的电源插座，否则当仪器出现漏电时，会引起触电。
使用和操作时应遵照“用户使用手册”的规定或指导。
不要用松脂油、笨等化学试剂清洁外部的污滓，因为它可能引起颜色和形状的变化，用软布或湿布擦洗，对于严重的污渍，用清洗剂或75%的酒精清洁。
如遇到螺钉或金属物掉进仪器内，以立即停止操做作，请有资质的维修人员将金属物取出后再开始操作，否则可能会引起仪器故障。
不要把试剂和水等放到仪器台面上，避免液体漏进仪器内部，对仪器造成损坏。
目录一、概述 (1)二、技术性能 (1)2.1输入功率 (1)2.2熔断器 (1)2.3工作条件 (1)2.5技术参数及功能 (1)2.6工作原理图 (2)2.7产品结构组成 (2)2.8外形示意图 (3)三、安装 (4)3.1开箱 (4)3.2电源及环境要求 (4)3.3管路连接 (4)3.4开机调验 (5)四、键盘功能简介 (6)五、仪器操作 (7)5.1清洗板路 (7)5.2冲洗管路 (14)5.3压力调节 (15)六、注意事项 (15)七、日常维护与保养 (16)7.1维护与保养 (16)7.2清洁 (16)7.3消毒 (16)7.4更换熔断器 (16)7.5周期性检查 (16)八、故障排除 (17)8.1开启电源，仪器无显示 (17)8.2接通电源，仪器有显示，但仪器不自检，按键无反应 (17)8.3洗板机工作时，清洗头短针无清洗液喷出，或出液量偏少 (17)8.4洗板完毕后，酶标板孔内残液量偏多 (17)8.5每次洗板时，清洗头短针注到酶标板微孔中的洗液量超标，洗液溢出 (17)8.6洗板机工作时，清洗头短针不停的出液 (17)8.7洗板机开机以后，仪器后部的排气嘴喷水或仪器底部漏水 (18)8.8清洗头与酶标板的位置不对，清洗头、托盘运动不灵活 (18)8.9仪器开机后，清洗头或托架运动不止 (18)九、维修服务 (19)十、附件 (19)一、概述DG3090型自动洗板机是配合我公司生产的DG5033系列酶联免疫检测仪而设计的产品，该产品具有操作简便、可靠性高、洗涤干净、适应多种规格酶标板的特点，其主要用途是在进行酶联免疫实验时清洗酶标板，实现酶联免疫实验过程中结合相与游离相的分离。
EBZ150掘进机
本掘进机由截割部、铲板部、第一运输机、本体部、行走部、后支承、液压系统、水系统、润滑系统、电气系统构成，总体结构见图1(第3页),液压原理见图2（第4页）
图1 总图
图2 液压原理图
2.2主要部Βιβλιοθήκη 的结构作用及工作原理2.2.1截割部由截割头、伸缩部、截割减速机、截割电机组成，见图3
图3截割部
2.2.2截割头为圆锥台形，在其圆周螺旋分布41把截齿。截割头通过花键套和2个M30的高强度螺栓与截割头轴相联，使主轴带动截割头旋转，见图4
图4截割头
2.2.3伸缩部位于截割头和截割减速机中间，通过伸缩油缸使截割头具有550mm的伸缩行程，见图5
图5伸缩部
2.2.4截割减速机是两级行星齿轮传动，它和伸缩部用26个M24的高强度螺栓相联。见图6
3.2.3 截割急停、总急停按钮
型式： 矿用隔爆型
规格型号： BZA1-10/24-1ZS 附带锁紧装置
额定电压： DC24V
额定电流： 10A 内部按钮为常开
用 途： 总急停按钮： 用于紧急停机
截割急停按钮： 用于截割电机停止
3.2.4 电铃：
型 式： 矿用隔爆型
规格型号： BAL1-36/127-150
(6).油泵电机和截割电机、二运电机之间启、停顺序，在电控系统中有闭锁装置；
(7).液压系统有过滤装置，还设有压力、油温、油位显示等保护装置；
(8).电控系统设有紧急切断和闭锁装置，在司机座位另一侧还装有紧急停止按钮；
(9).掘进机设有内、外喷雾系统，并有过滤装置、漏水检测及保护功能。
2.EBZ150A（S150JA）掘进机结构特征与工作原理
3.1.2 截割范围：
掘进机培训教材PPT课件
一 掘进机的发展历程及方向 二 掘进机概论 三 掘进机整机构成及各部功能 四 各部详细结构 五 液压系统 六 水系统和润滑系统 七 解体与运输 八 组装及调试 九 操作 十 维护与保养 十一 故障判断及排除 十二 检修
1
发展历程及方向
1951年，在匈牙利形成了现代掘进机 的雏 形。20世纪60 年代后，掘进机获得了飞速 发展。我国在1962年以后，定型生产了几 种掘进机，1979年大量引进（共100台）。
驱动链轮及履带实现行走。履带采用油脂缸涨紧，
用高压油脂枪向涨紧油缸注油脂涨紧嘴，泄除缸
内压力后拧紧油嘴，使涨紧油缸活塞杆不受涨紧
力。履带架通过键及高强度螺栓固定在本体两侧，
在其侧面开有方槽,以便涨紧油缸的拆卸。行走减
速机用高强度螺栓与履带架联接。
行走部的功能是带动机器前进、后退或转弯。
26
PARKER高压胶管
通径标记与公制尺寸换算
05 — 7.9375 φ8 5/16×25.4=7.9375
06 — 9.525 φ9.5
08 — 12.7
φ12.7
10 — 15.875 φ16
12 — 19.05 φ19
16 — 25.4
φ25.4
20 — 31.75 φ 32
达和油缸。共有13个油缸，其中截割头升降油缸、
铲板升降油缸、后支撑器的升降油缸均设有安全
型平衡阀。刮板涨紧油缸、履带涨紧油缸安装了
液压锁。液压系统还为液压锚杆钻机提供接口。
2、操纵台上设有各种换向阀，通过手柄完
成油缸及液压马达的动作，在其上还装有旋阀、
压力表、压力式温度计。转动旋阀可观擦各系统
的压力值，压力式温度计可直接读出油箱内的油
2023年Hyundai Motor India限量版产品介绍说明书
Hyundai Motor India Ltd.Plot C-11, City Center, Sector-29Gurugram, Haryana Pin Code - 122 001Visit us at www.hyundai.co.in or call us at 1800-11-4645 (Toll Free) 098-7356-4645.For more details,please consult your Hyundai dealer.Dealer’s Name & AddressALCAZARC o p y r i g h t © 2023. H y u n d a i M o t o r I n d i a L i m i t e d . A l l R i g h t s R e s e r v e d .M a r -A p r , 2023Some of the equipment illustrated or described in this leaflet may not be supplied as standard equipment and may be available at extra cost. • Hyundai Motor India reserves the right to change specifications, schemes and equipment without prior notice. • Functionality of Bluelink depends on adequate power supply and uninterrupted network connectivity to infotainment system. The Bluelink system is designed in such a way that it makes vehicle theft difficult if its circuit and battery connection is uninterrupted • Hyundai Motor India recommends you to avoid using backcovers for mobiles while charging your phone on the wireless charger • ^Upto 7 years extended warranty is applicable only for petrol variants. Hyundai ALCAZAR (Petrol) has lowest average yearly periodic maintenance service cost in its segment of ₹ 3 442 for 5 years in Delhi. Source: . • The colour plates shown may vary slightly from the actual colours due to the limitations of the printing process. Please consult your dealer for full information and availability on colours and trim. *Terms & conditions apply.Peace of mind3 Years Bluelink subscriptionmyHyundaiappWelcome to the grand life.For those with a passion for the refined things in life and those who want to explore for themselves, presenting to you the new Hyundai ALCAZAR.For those who dare to be different, who want finer experiences and never compromise on quality, the Hyundai ALCAZAR ushers in a new dimension of driving sophistication. Drawing its inspiration from the royal lineage of castles and palaces, denoting grandeur, spaciousness, and solidity, this SUV has been crafted as the SUV of choice for the visionaries and leaders of tomorrow. A true testament to its regal inspiration, the Hyundai ALCAZAR stands tall as the embodiment of premiumness.Tough, yet graceful. Dominating, yet elegant. Hyundai ALCAZAR pairs a bold and tall stance with the elegant design that is unmistakably premium. A haven of refinement, where aesthetic design meets supreme craftsmanship. For people with an exquisite palate, equipped with features that add a sophisticated touch to the bold and solid exterior.The Hyundai ALCAZAR features contemporary trio beam LED headlamps and tail lamp design flowing into the lines of the body. The superior poise of the stylish chrome radiator grille and the expertly styled twin tip exhaust adds a sense of grace to the Hyundai ALCAZAR’s effortless stature.Elegance from every angle.Other features: LED positioning lamps I Crescent glow LED DRLs I Trio beam LED headlamps Dark front chrome grille I LED fog lamps I Shark fin antennaOther features: Large day light opening (DLO) area I Side foot step (1st in segment)R18 (D=462 mm) Diamond cut alloys Honey-comb inspired LED tail lampsPuddle lamps with logo projectionDark front chrome grille*Turbo emblem*Twin tip exhaust *Available in 1.5 l petrol turbo variantThe interior of the Hyundai ALCAZAR immerses you in uncluttered design. Complete with premium dual tone cognac brown interiors, the 64 colours ambient lighting offers a regal touch to the cabin. Carefully selected materials accentuate the aesthetic, complete with Hyundai ALCAZAR’s advanced technology, ensuring that your entertainment knows no bounds. Experience serenity thanks to a voice controlled panoramic sunroof and an auto healthy air purifier. The tranquil sanctuary is also outfitted with an HD touchscreen system with powerful Bose premium sound system, immersing you in a richand balanced premium audio experience.Premium dual tone cognac brown interiors Panoramic sunroof26.03 cm (10.25”) HD touchscreen system Auto healthy air purifier with AQI displayBose premium sound system (8 speakers)26.03 cm (10.25”) Multi display digitalcluster with personalized themesExtravagant comfort. Plush ride.Leather pack: Perforated D-cut steering wheel I Perforated gear knob I Cognac brown and black seat upholstery IDoor armrest Power driver seat – 8 wayInside the Hyundai ALCAZAR, you always travel first class. For short jaunts or epic getaways, envelope yourself in sublime comfort with immersive front row ventilated seats. Extravagantly comfortable captain seats in the second row (6 seater) complete with the versatility to tip, tumble, slide and recline let you sit back in pure comfort. Relax, lean back and unwind in the tranquility of the Hyundai ALCAZAR.Adore your private palatial retreat on wheels wherever the journey takes you.Fluidly adapts to your needs.Multiple seating designsFront row sliding sunvisor 4 USB chargers for 3 rowsFront row seatback table with retractable cup-holder and IT device holder2nd row - one touch tip tumble captain & split seats3rd row AC vents with speed control (3-stage)2nd row headrest cushion1st & 2nd row smartphone wireless charger2nd row captain seats with premium console armrestEach element of the Hyundai ALCAZAR has been designed to provide excellence in comfort and in safety. Complete with highly accurate front & rear parking sensors and state-of-the-art security alerts like speed alert system, you’re always one step ahead of unexpected events on the road. Each journey in the Hyundai ALCAZAR inspires awe and admiration as it carries passengers in uncompromised safety.A new paradigm in safety.Other features: Emergency stop signal I Speed alert system I Speed sensing auto door lock I Driver rear view monitor Impact sensing auto door unlock I Child seat anchor (ISOFIX) IElectric parking brake with auto holdStrong body structure with AHSSWith ESC Without ESCParking assist: Front and rear parking sensors6 Airbags Hill start assist control (HAC)Rear disc brakes Tyre pressure monitoring system (Highline)Surround view monitor (SVM)Electronic stability control (ESC)Vehicle stability managment (VSM)Blind view monitor (BVM)Standard across all variants6 AirbagsESC VSM HACISOFIXOther features: Cruise control I Paddle shifters (1st in segment)Desert sands. Mountain slopes. Rugged river valleys. No frontier is out of bounds for the Hyundai ALCAZAR. The power to control your drive is at your fingertips. Equipped with powerful petrol or diesel engines that give you the perfect balance between performance and efficiency, the Hyundai ALCAZAR conquers every landscape with effortless ease.Whether you’re taking to the road or exploring out into the unknown you’ll always have a great drive.Conquer any horizon.Max torque 253Nm (25.8 kgm)/1500 – 3500 r/min1.5 l petrol Turbo GDi engine1.5 l diesel CRDi engine6-speed manual & 7-speed dual clutch transmission options available for petrol turbo engine and 6-speed manual & automatic transmission options available for diesel engine.Max power117.5 kW (160 PS)/ 5 500 r/minMax torque 250 Nm (25.5 kgm) / 1 500-2 750 r/minMax power85 kW (116 PS) / 4 000 r/minWe’ve created technology to serve you and make your life easier, intuitively and simply. Stay seamlessly connected with your Hyundai ALCAZAR and the world, with Bluelink. The Hyundai ALCAZAR offers outstanding capability on and off the road. Choose between driving modes for everyday driving or traction modes for any terrain you need to conquer.Technology that takes you further.Drive mode select Traction control modesAdvanced Bluelink with OTA map updatesOther features: Welcome greetings I Voice recognition commands (I want to see the sky / What’s the Indian cricket score? / When is the soccer match?) I Bluelink integrated smartwatch appwith 60+ features and OTA map updatesKey featuresTechnical specificationsDimensions Overall length (mm) 4 500 Overall width (mm) 1 790 Overall height (mm) 1 675^^ Wheelbase (mm) 2 760 Fuel tank capacity (l)50EngineConfiguration 4 Cylinders,16 Valves4 Cylinders, 16 ValvesCam typeDOHC Displacement (cm ) 1 4821 493Fuel system GDiCommon rail direct injection (CRDi)Max power 117.5 kW (160 PS)/ 5 500r/min 85 kW (116 PS) / 4 000 r/min Max torque 253 Nm(25.8 kgm)/1500 –3500 r/min 250 Nm (25.5 kgm) / 1 500-2 750 r/minTransmission6-speed manual6-speed manual Type7-speed DCT6-speed automaticSuspension Front McPherson strut with coil spring RearCoupled torsion beam axle (CTBA) BrakesFront Disc Rear Disc Tyre215/60 R17 (D=436.6 mm) alloy (prestige)Size215/55 R18 (D=462 mm) alloy (platinum, signature)Spare wheel215/60 R17 (D=436.6 mm) steel (all trims)Items1.5 l petrol turbo GDi engine1.5 l diesel CRDi engineVariantPlatinum Prestige (O)PrestigePlatinum (O)Signature Signature(O)VariantPlatinum Prestige(O)PrestigePlatinum (O)Signature Signature(O)Engine & trim plan 1.5 l petrol turbo 6 seater - - - DCT - DCT GDi engine 7 seater MT - MT DCT - DCT 1.5 l diesel 6 seater - - - AT MT AT CRDi engine 7 seater MT AT MT AT - AT Safety Rear disc brakes S S S S S S ABS with EBD S S S S S S Electronic stability control (ESC) S S S S S S Vehicle stability management (VSM) S S S S S S Hill start assist control (HAC) S S S S S S Automatic headlamps S S S S S S LED fog lamps S S S S S S Tyre Pressure Monitoring System S S S S S S Electro chromic mirror (ECM) S S S S S S Emergency stop signal (ESS) S S S S S S Speed alert system S S S S S S Standard safety Speed sensing auto door lock S S S S S S Lane change indicator flash adjustment S S S S S S Rear defogger with timer S S S S S S Driver rear view monitor S S S S S S Rear parking sensors S S S S S S Rear camera with steering adaptiveS S S S S Sparking guidelines Seatbelt reminder (all seats) S S S S S S Front seat belts with pretensioner S S S S S S 3 Point seat belts (all seats) S S S S S S Impact sensing auto door unlock S S S S S S Child seat anchor (ISOFIX) S S S S S S Driver & passenger airbags S S S S S S Burglar alarm S S S S S S Front parking sensors - - - - S S Side & curtain airbags S S S S S S Surround view monitor (SVM) - - S S S S Blind view monitor (BVM) - - S S S S Height adjustable front seatbelts - driver & passenger S S S S S S Exterior Trio beam LED headlamps S S S S S S LED positioning lamps S S S S S S Crescent glow LED DRLs S S S S S S Honey-comb inspired LED tail lamps S S S S S S Puddle lamps with logo projection - - S S S S LED turn indicators on outside mirrors S S S S S S Front grille S S S S S S Dark chrome Fog lamp garnish S S S S S S exterior finish Outside door handles S S S S S S Tailgate garnish S S S S S S Body colour dual tone bumpers S S S S S S Front & rear skid plate S S S S S SORVM Body colour S S S S S SBlack - - - - Dual Tone Dual Tone A-Pillar piano black finish S S S S S S B-Pillar black-out tape^ S S S S S S C-Pillar garnish piano black finish S S S S S S Integrated Silver S S S S S S roof rails Matte Black - - - - Dual Tone Dual Tone Shark fin Body colour S S S S S S antenna Black - - - - Dual Tone Dual ToneRear spoiler Body colour S S S S S SBlack - - - - Dual Tone Dual Tone Twin tip exhaust S S S S S SWheelsR17 (D=436.6 mm) Diamond cut alloys S S - - - - R18 (D=462 mm) Diamond cut alloys - - S S S S Side foot step - - - S - S Dual-tone exterior - - - - O 6S Interior Premium dual tone cognac brown interiors S S S S S S 17.78 cm (7”) Supervision cluster S S - - - -26.03 cm (10.25”) Multi display digital cluster - - S S S S Piano-black interior finish S S S S S S Perforated D-cut steering wheel S S S S S SLeather packPerforated gear knob S S S S S S Cognac brown & black seat upholstery - - S S S S Door armrest - - S S S S Metal finish inside door handles S S S S S S 64 Colours Crashpad S S S S S S ambient lighting Front & rear doors S S S S S S Metallic door scuff plates S S S S S SComfort and conveniencePanoramic sunroof S S S S S S Electric parking brake with auto hold - S S S S S Smart key with push button start S S S S S S Remote engine start with smart key S S S S S S Tilt & telescopic steering S S S S S S Front row ventilated seats - - - - S S Front row sliding sunvisor S S S S S S Auto healthy air purifier with AQI display - S S S S S Drive mode select (comfort | eco | sport) - S - S - S Traction control modes (snow | sand | mud) - S - S - S Paddle shifters - S - S - S Cruise control S S S S S SAir conditioning Fully automatic temperature control S S S S S Swith eco coating S S S S S SOutside mirror Electrically adjustable & foldable S S S S S Swith auto folding S S S S S S Front smartphone wireless charger S S S S S S Front console armrest with storage S S S S S S Front row seatback tablewith retractable cup-holder & IT device holder S S S S S SFront seat back pocket S S S S S S 2 row headrest cushion - - S S S S Rear centre armrest 7S 7S 7S 7S - 7S Premium 2 row console with smartphone wirelesscharger, storage & cup holders - - - 6S 6S 6SRear window sunshade S S S S S S 2row AC vents S S S S S S 3 row AC vents with speed control (3-stage) S S S S S S 1 row S S S S S SUSB charger 2 row S S S S S S 3 row 1 unit 1 unit 2 units 2 units 2 units 2 units Front power outlet S S S S S S Rear wiper and washer S S S S S S LED map & reading lamps S S S S S S Luggage lamp S S S S S SPower windows Front & rear S S S S S SDriver side auto up-down (safety) S S S S S S Sunglass holder S S S S S S Passenger vanity mirror S S S S S S Glove box cooling S S S S S S Roof assist handle S S S S S S Tinted glass S S S S S S Electric tailgate release S S S S S S Battery saver S S S S S S Follow-me-home headlamps S S S S S S Inside door handle override: driver S S S S S S Idle stop & go (ISG) S S S S S S Seating Height adjustable driver seat S S S S S S Power driver seat - 8 way - - S S S S Height adjustable headrest - all 3 rows S S S S S S Captain seats - - - 6S 6S 6S2 row 60:40 split seat 7S 7S 7S 7S - 7S Sliding & reclining seat S S S S S S One touch tip and tumble S S S S S S3 row 50:50 split seat S S S S S SReclining seat S S S S S S Infotainment and connectivityInfotainment 26.03 cm (10.25”) HD touchscreen S S S S S Ssystem Navigation S S S S S S Bluetooth S S S S S S Smartphone Apple CarPlay S S S S S S connectivity Android Auto S S S S S S Steering Audio control S S S S S S mounted Voice recognition S S S S S S controls Bluetooth handsfree S S S S S S Bose premium sound system (8 speakers) - - S S S S Front & rear door speakers S S S S S SSpeaker System Front tweeters S S S S S SFront central speaker - - S S S S Sub-woofer - - S S S S Advanced Hyundai Bluelink (connected-car technology) S S S S S S Over-the-air (OTA) map updates S S S S S S Bluelink integrated smartwatch app S S S S S S ^^With roof railsDimensionsunit : mmExterior coloursSingle toneDual toneStarry nightTitan greyTyphoon silverS - Standard O - Optional Leatherette ^Except abyss black colour6S - 6 Seater 7S - 7 SeaterAbyss blackAtlas whiteTaiga brownTitan grey + abyss blackAtlas white+ abyss black2 7604 5001 7901 675Disclaimer : Dual tone colour option is available in signature 6S trim only.。
S150说明书
KXJ2-148/1140E矿用隔爆兼本质安全型掘进机用电控装置使用说明书兖矿集团有限公司机械制修厂二OO二年八月二十日目录1、概述---------------------------------12、电气系统的工作原理-------------------43、电气控制系统操作方法及过程-----------54、各种显示及其内容---------------------85、电控箱上腔接线说明-------------------96、电机参数及要求-----------------------97、使用及注意事项-----------------------98、故障的排除及维护---------------------109、维护保养-----------------------------1110、运输与储存---------------------------1111、定货须知-----------------------------1112、附图一 ------------------------------1213、附图二 ------------------------------1314、操作箱接线图 ------------------------1415、控制器布线图 ------------------------1516、显示板布线图 ------------------------1617、继电器板布线图 ----------------------1718、安装板布线图 ------------------------181、概述KXJZ-148/1140E矿用隔爆兼本质安全型掘进机用电控装置是S150掘进机的控制核心，它控制着掘进机电动机的运转、停止、行走以及提供照明电源和各种保护等。
该说明书针对掘进机电控装置（以下简称电控装置）的使用、维修等加以简要说明。
该装置包括KXJZ-148/1140E矿用隔爆兼本质安全型掘进机用电控箱（以下简称电控箱）和TJ1-24E矿用隔爆兼本质安全型掘进机用操作箱（以下简称操作箱）。
综掘机150A技术规格书[1]
![综掘机150A技术规格书[1]](https://img.taocdn.com/s3/m/7cc248f2112de2bd960590c69ec3d5bbfc0ada44.png)
综掘机150A技术规格书[1]EBZ150A掘进机技术规格书一技术要求本次掘进机配套要求所有零部件与原供长平公司同型号产品保持一致。
机体总长： 9.34 m机高： 1.65m(不含临时支护的高度)机重：约50T铲板宽度： 2.9m履带外宽： 2.52m截割宽度： 5.5m截割高度： 4.8m截割面积： 26㎡爬坡能力：±16o铲板卧底深度： 216mm截割头底深度： 220mm(截割头伸出时)龙门高度： 450mm截割硬度≤65mpa接地比压 0.14mpa液压系统压力最大18mpa总功率 236kw供电电压 1140V/660V1)．技术参数：截割头形状圆锥台形截割轴形式纵轴式截割头转数 46/23截割头伸缩量 500mm截割电机YBUD150/80KW-4/8P隔爆型双速水冷1台喷雾内、外喷雾方式2)．铲板部装载形式星轮装载宽度 2.9m星轮转数 33转/min装载能力 4.2m3/min3)．一运输机形式边双链刮板式溜槽宽度 540mm（宽）*370mm(高)链速 61m/min运输能力 6m3/min第一运输机驱动方式液压马达涨紧形式弹簧丝杠涨紧4)．走部形式履带式 2条履带宽度 520mm制动方式一体式多片制动器（减速机内置）接地比压 0.14mpa行走速度 0－6m/min行走马达 2台行走减速 2台涨紧形式油缸涨紧、卡板琐紧5）.第二运输机形式桥式转载机驱动方式 11kw电滚筒运输能力 5m3/min带宽 800mm胶带阻燃皮带6）．压力系统压力 18mpa柱塞变量双泵(ml/r) A11VO130/130 1台液压马达排量行走部ml/r: A2FE125铲板部ml/r： LAM1200.H4第一运输机部ml/r: LAM400.H2油箱容量L 500油泵电动机 YUS-75 隔爆风冷 1台换向阀手动式 2台油冷却器水冷却式 1台油泵电机隔爆风冷式DYB-75KW 1台7）.系统外来水量L/min 100外喷雾水压Mpa 1.5内喷雾水压Mpa 3.0内喷雾泵 PQ-40 1台内喷雾泵马达 ME36 1台8）．电器部分主回路额定电压 AC 1140V/660V额定电流≤300额定频率 50HZ输出分路数 4额定功率 236KW照明电压 AC24V-50HZ9）.截割电机型式：掘进机用隔爆型三项异步电动机水冷式规格型号 YUB-150/80-4/8H级绝缘等级：H级工作方式：S1 额定电压AC1140V/660V Y/⊿额定电流高速 90A/156A 低60A/104A油泵电机：型式：掘进机用隔爆型三项异步电动机风冷式规格型号 YUB-75 级绝缘等级：H级工作方式：S1额定电压AC1140V/660V Y/⊿额定电流 47.1A/81.5A10）.截割急停、总急停按钮、电铃、照明灯：型式：矿用隔爆型规格型号 BZA1-10/24-1ZS附带锁紧装置额定电压 DC24V额定电流 10A内部按钮为常开用途总急停按扭：用于紧急停机；截割急停按钮：用于截割电机停止电铃型式：矿用隔爆型规格型号：BAL-36/127/150矿用隔爆型电铃额定电压 AC127V额定电流 0.35A用途开机信号，启动报警。
胜家SE9150 SE9155 SE9180 SE9185 操作说明书
重要安全说明使用本电器时，务必遵守以下基本安全预防措施：请在使用此缝纫机前阅读所有说明。
将说明置于机器附近。
如将机器给予第三方，请确保将手册一并送予。
危险 - 要降低电击风险：缝纫机插上电源时，不得无人看管。
机器所插入的电源插座应该容易接近。
在使用后，清洁、打开机盖、润滑前，或者在进行说明手册中提到的其他任何维护调整时，请拔掉电源。
警告 - 要降低烫伤、火灾、电击或人身伤害风险：• 此设备供成人使用。
本电器可供（i） 8 至 12 岁的儿童以及（ii）身体、感官或心理能力较弱或缺乏经验和知识的人士在获得监督或指导安全使用电器的方法并明白相关危险的情况下使用。
在没有监督的情况下，儿童不可清洁和维修本电器。
不允许任何人玩这台机器。
8 岁以下的儿童不得使用本设备。
• 请勿将机器用作玩具。
缝纫机由儿童操作或在儿童附近使用时需特别注意。
• 仅按本手册所述指定用途来使用本缝纫机。
仅使用手册中制造商推荐附件。
• 切勿操作电源线或插头损坏、无法正常工作、跌落或损坏或者落入水中的缝纫机。
将缝纫机送至最近的授权经销商或维修中心进行检查、维修、电气或机械调整。
• 切勿在通风孔堵塞的情况下操作缝纫机。
保持缝纫机通风孔和脚踏控制器清洁，避免棉绒、灰尘和碎布积聚。
• 手指应远离所有活动部件。
在缝纫机针周围需要特别注意。
• 务必使用正确的针板。
错误的针板会导致机针折断。
• 请勿使用弯曲的机针。
• 请勿在缝纫时推拉布料。
否则可能会使机针偏斜，导致机针折断。
• 佩戴安全眼镜。
• 在机针区域进行机针穿线、换针、换底线或更换压脚等调整时，应转至“0”关闭机器。
• 切勿将任何物体丢进或插入通风口。
• 请勿在室外使用。
• 请勿在使用喷雾（喷撒）产品或氧气含量受控的环境下操作。
• 要断开机器，应将所有控制装置转至 (“0”) 位置，然后从插座中拔下插头。
• 拔下插头时请勿拉扯电源线。
要拔下插头，应抓住插头，而非电源线。
• 脚踏控制器用于操作机器。
FastTrak S150 TX2plus 快速入门指南说明书
Version 1.2FastTrak S150 TX2plusCopyright© 2003 Promise Technology, Inc. No part of this manual may be reproduced or transmitted in any form without the expressed, written permission of Promise Technology.TrademarksPromise, and the Promise logo are registered in U.S. Patent and TrademarkOffice.All other product names mentioned herein may be trademarks or registeredtrademarks of their respective companies.Important Data Protection InformationYou should back up all data before installing any drive controller or storageperipheral. Promise Technology is not responsible for any loss of data resulting from the use, disuse or misuse of this or any other Promise Technology product. NoticeAlthough Promise Technology has attempted to ensure the accuracy of thecontent of this manual, it is possible that this document may contain technical inaccuracies, typographical, or other errors. Promise Technology assumes no liability for any error in this publication, and for damages, whether direct, indirect, incidental, consequential or otherwise, that may result from such error, including, but not limited to loss of data or profits.Promise Technology provides this publication “as is” without warranty of anykind, either express or implied, including, but not limited to implied warranties of merchantability or fitness for a particular purpose.The published information in the manual is subject to change without notice.Promise Technology reserves the right to make changes in the product design, layout, and driver revisions without notification to its users.ContentsStep 1: Unpack Your FastTrak Card (3)Step 2: Install the FastTrak Card (4)Step 3: Install the Hard Drives (5)Step 4: Create Your Disk Array (7)Creating a Performance Array (8)Creating a Security Array with New Drives (9)Creating a Security Array with an Existing Data Drive (11)Creating a Security Array with Quick Initialization (14)Step 5: Install Software Drivers (16)Quick Start Guide Step 1: Unpack Your FastTrak Card When you receive the FastTrak S150 TX2plus card, the package should contain the items listed below:• FastTrak S150 TX2plus RAID Controller Card• Quick Start Guide• FastTrak S150 TX2plus driver diskette• Two internal 4-wire Serial ATA hard drive data cables• One internal 40-pin Parallel ATA data cable• One Y power splitter cable• CD with Drivers, Promise Array Management (PAM) utility, PAM User Manual and FastTrak S150 TX2plus User ManualIf ANY of the contents are missing or appear to be damaged, please contactyour dealer or distributor immediately.WarningBefore installing the adapter into an existing system, backup anyimportant or useful data. Failure to follow this accepted PCpractice could result in data loss.WarningThe FastTrak S150 TX2plus Ultra ATA/Serial ATA RAIDController card, like other parts of your system, is subject todamage by static electricity. Be sure that you’re properlygrounded (Promise recommends that you wear an anti-staticstrap or touch a grounded object) and that you unplug yoursystem before installing FastTrak.FastTrak S150 TX2plusStep 2: Install the FastTrak CardThe FastTrak TX2plus Serial ATA RAID card fits into any available PCI slot on your PC’s motherboard (see Figure 1, below):• 32-bit PCI slot (must be PCI 2.2 or 2.3 compliant)• The 32-bit portion of a 64-bit PCI slot1. Remove the cover of your system.2. Remove the inside slot cover of an available 32-bit PCI slot on themotherboard.3. Install the FastTrak Serial ATA RAID card into the open slot (see Figure 1below). Secure the bracket to the system’s frame.4. Attach your system case’s 2- or 4-pin LED cable to the LED connector onthe FastTrak S150 TX2plus RAID card (see Figure 2, on page 6). Makesure that pin 1 on the connector is aligned with pin 1 of the cable.5. Fasten the controller card bracket to the system case (see below).Figure 1. Insert the FastTrak card into an open PCI slotQuick Start Guide Step 3: Install the Hard DrivesImportantIf you wish to include your current bootable Serial ATA driveusing the Windows NT 4.0, Windows 2000, or Windows XPoperating system as part of a bootable Mirrored (RAID 1) arrayon your FastTrak Serial ATA RAID card, do NOT connect thehard drive to the FastTrak yet.You MUST install the Windows NT4, 2000, or XP driver softwarefirst onto this drive while it is still attached to your existing harddrive controller.The FastTrak Serial ATA RAID card supports up to two Serial ATA hard drives and up to two Ultra ATA/133 drives. For optimal performance, install twoidentical Serial ATA drives and two identical Ultra ATA drives of the same model and capacity. The drives’ matched performance allows the array to functionbetter as a single drive.If you are striping (RAID 0) for performance, use up to four new drives. Ifmirroring (RAID 1) for protection, you can use two new drives OR use anexisting drive and a new drive (the new drive must be the same size or larger than the existing drive).1. Install the hard drives into the hard drive bays of your system, including thepower cables.CautionUse of removable hard drive enclosures other than PromiseTechnology’s SuperSwap is not supported and may result inperformance loss or other undesired results.2. Attach one Serial ATA data cable to each Serial ATA hard drive. Thenattach the other ends of the cables to the connectors on the FastTrakTX2plus RAID card.3. Attach a black connector of the Ultra ATA cable to each Parallel ATA harddrive.4. Attach the blue cable connector to the Port 3 Parallel connector on theFastTrak S150 TX2plus controller card. The colored edge of the cable(s)indicates pin 1 (see Figure 2).FastTrak S150 TX2plusFigure 2. FastTrak S150 TX2plus card5. Attach the Y-cable power splitters to the Serial ATA hard drives.6. Use existing power cables for the Parallel ATA hard drives.NoteThe FastTrak S150 TX2plus RAID controller is a PCI Plug-n-Play (PnP) device. No changes are necessary in the Motherboard CMOS Setup for resources or drive types in most applications.Quick Start GuideStep 4: Create Your Disk ArrayYou will now use the onboard FastBuild™ BIOS utility to create your array using the attached drives. There are three different scenarios in creating this array.You can create an array for:• Performance• Security, using new hard drives (recommended)• Security, using an existing hard drive and a new one• Security, using Quick InitializationThe first three steps are the same for all three choices. After that, follow thesteps for the array you want to create.1. Boot your system. If this is the first time you have booted with the FastTrakS150 TX2plus card and drives installed, the Promise onboard BIOS willdisplay the following screen.FastTrak S150 TXx (tm) BIOS Version 1.aa (Build xxxx)(c) 2002-2005 Promise Technology, Inc. All Rights ReservedNo array defined . . .Press <Ctrl-F> to ender FastBuild (tm) UtilityOr press <ESC> key to continue booting the system2. Press the Ctrl-F keys to display the FastBuild Utility Main Menu.3. Press “1” to display the Auto Setup Menu below. This is the fastest andeasiest method to creating your first array.FastTrak S150 TX2plusFastBuild (tm) Utility 2.xx(c) 2002-2005 Promise Technology, Inc.[Auto Setup Options Menu]Optimize Array for: Performance[ Auto Setup Configuration ]Mode.......................................................................StripeDrive 0SpareDrives used in Array (2)Array Disk Capacity (160048)[ Keys Available ][↑] Up [↓] Down [←, →, Space] Change Option [ESC] Exit [Ctrl-Y] Save Creating a Performance ArrayFastTrak S150 TX2plus enables you to create striped or mirrored arrays with 1, 2, 3, or 4 drives.To create an array for best performance, follow these steps:1. Press the Spacebar to choose Performance under the Optimize Array forsection.2. Press Ctrl-Y to Save and create the array.3. Reboot your system.4. Once the array has been created, you will need to FDISK and format thearray as if it were a new single hard drive.5. Once the arrayed drives have been formatted, proceed to Chapter 4 of thisManual to install your operating system and/or FastTrak driver.Quick Start Guide Creating a Security Array with New DrivesCautionWith some models of hard drives, if the Master hard drive fails, itmay cause the Slave hard drive to be unrecognized by thecomputer's operating system. Where a RAID 1 (Mirroring) arrayexists on the Master/Slave pair, this condition may cause theoperating system to freeze.Do NOT create a RAID 1 (Mirroring) array with two Parallel ATAhard drives using the Master/Slave arrangement on Channel 3(the Parallel ATA port).You can create a RAID 1 (Mirroring) array by combining harddrives on:•Channels 1 and 2 (Serial ATA only)•Channels 1 and 3 (one Serial, one Parallel)•Channels 2 and 3 (one Serial, one Parallel)Under the Security setting, FastTrak S150 TX2plus permits two drives to beused for a single Mirrored array or four drives to be used for a Mirrored/Striped array in Auto Setup.NoteWhen creating a Security array with new drives, a feature calledGigabyte Boundary will automatically be set to ON. For adescription of this feature, see page 27 of the User Manual onthe software CD.To create an array for data protection using new hard drives, follow these steps:1. Press the Spacebar to choose Security under the Optimize Array forsection.2. Press Ctrl-Y to Save your selection.3. The window below will appear.Do you want the disk image to beduplicated to another or do quickinitialize or create only?Y - Create and DuplicateN - Create OnlyI - Create and Quick Initialize4. Press N for the Create Only option.FastTrak S150 TX2plus5. A window will appear almost immediately confirming that your Security arrayhas been created. Press any key to reboot the system.Array has been created.<Press Any Key to Reboot>6. Proceed with normal FDISK and format procedures as if you had justinstalled a new hard drive.7. Once the arrayed drives have been formatted, proceed to Chapter 4 of thisManual to install your operating system and/or FastTrak driver.Creating a Security Array with an Existing Data DriveCautionWith some models of hard drives, if the Master hard drive fails, itmay cause the Slave hard drive to be unrecognized by thecomputer's operating system. Where a RAID 1 (Mirroring) arrayexists on the Master/Slave pair, this condition may cause theoperating system to freeze.Do NOT create a RAID 1 (Mirroring) array with two Parallel ATAhard drives using the Master/Slave arrangement on Channel 3(the Parallel ATA port).You can create a RAID 1 (Mirroring) array by combining harddrives on:•Channels 1 and 2 (Serial ATA only)•Channels 1 and 3 (one Serial, one Parallel)•Channels 2 and 3 (one Serial, one Parallel)Under the Security setting, FastTrak S150 TX2plus permits two drives to be used for a single Mirrored array or four drives to be used for a Mirrored/Striped array in Auto Setup.You would use this method if you wish to use a drive that already contains data and/or is the bootable system drive in your system. You will need another drive of identical or larger storage capacity.WarningIf you are creating a Security array using an existing hard drive,backup any important data. Failure to do so could result in dataloss.ImportantIf you wish to include your current bootable drive using theWindows NT 4.0, Windows 2000, or Windows XP operatingsystem as part of a bootable Mirrored (RAID 1) array on yourFastTrak S150 TX2plus, do NOT connect the hard drive to theFastTrak yet.You MUST install the Windows NT4, 2000, or XP driver softwarefirst to this drive while it is still attached to your existing harddrive controller. See chapter 4 of this Manual.Follow these steps:1. Press the Spacebar to choose Security under the Optimize Array forsection.2. Press Ctrl-Y to Save your selection. The window below will appear.Do you want the disk image to beduplicated to another or do quickinitialize or create only?Y - Create and DuplicateN - Create OnlyI - Create and Quick Initialize3. Press Y for the Create and Duplicate option. The window below will appearasking you to select the Source drive to use. FastBuild will copy all datafrom the Source drive to the Target drive.Source DiskChannel:ID Drive Model Capacity (MB)----- ----------Target DiskChannel:ID Drive Model Capacity (MB)----- ---------- [Please Select A Source Disk]Channel:ID Drive Model Capacity (MB)1 : SEAGATE S380023AS 800242 : SEAGATE S380023AS 80024[↑] Up [↓] Down [ESC] Exit [Ctrl-Y] Save4. Use the arrow keys to choose which drive contains the existing data to becopied.5. Press Ctrl-Y to Save selection and start duplication. The following progressscreen will appear.Start to duplicate the image . . .Do you want to continue? (Yes/No)Y – Continue N - Abort6. Select Y to continue. If you choose N, you will be returned to step 1.7. Once complete, the following screen will appear confirming that yourSecurity array has been created. Press any key to reboot the system.Array has been created.<Press Any Key to Reboot>8. Once the arrayed drives have been formatted, proceed to Chapter 4 of thisManual to install your operating system and/or FastTrak driver.Creating a Security Array with Quick InitializationCautionWith some models of hard drives, if the Master hard drive fails, itmay cause the Slave hard drive to be unrecognized by thecomputer's operating system. Where a RAID 1 (Mirroring) arrayexists on the Master/Slave pair, this condition may cause theoperating system to freeze.Do NOT create a RAID 1 (Mirroring) array with two Parallel ATAhard drives using the Master/Slave arrangement on Channel 3(the Parallel ATA port).You can create a RAID 1 (Mirroring) array by combining harddrives on:•Channels 1 and 2 (Serial ATA only)•Channels 1 and 3 (one Serial, one Parallel)•Channels 2 and 3 (one Serial, one Parallel)Under the Security setting, FastTrak S150 TX2plus permits two drives to beused for a single Mirrored array or four drives to be used for a Mirrored/Striped array in Auto Setup.You would use this method if you wish to create a mirrored array and erase the early block from your existing drives.WarningUsing the Quick Initialization option on existing drives will resultin the loss of all data on those drives.NoteWhen creating a Security array with new drives, a feature calledGigabyte Boundary will automatically be set to ON. For adescription of this feature, see page 27 of the User Manual onthe software CD.To create an array for data protection using new hard drives, follow these steps:1. Press the Spacebar to choose Security under the Optimize Array forsection.2. Press Ctrl-Y to Save your selection.3. The window below will appear.Do you want the disk image to beduplicated to another or do quickinitialize or create only?Y - Create and DuplicateN - Create OnlyI - Create and Quick Initialize4. Press I for the Create and Quick Initialize5. A window will appear almost immediately confirming that your Security arrayhas been created. Press any key to reboot the system.Array has been created.<Press Any Key to Reboot>6. Proceed with normal FDISK and format procedures as if you had justinstalled a new hard drive.7. Once the arrayed drives have been formatted, proceed to Chapter 4 of thisManual to install your operating system and/or FastTrak driver.Step 5: Install Software DriversDrivers for the Windows operating systems are included on the software CD and driver diskette that came with your FastTrak S150 TX2plus Controller.Windows systems usually recognize the FastTrak Controller, prompt you for the CD or diskette and perform the driver installation automatically.If you are installing the FastTrak Controller at the same time as your operating system or you prefer to read step-by-step directions, see Chapter 4 of the User Manual on the software CD.Drivers and installation instructions for other Operating Systems aredownloadable from the Promise website at .。
可调速驱动器S15（重型）低压说明书
ADJUSTABLE SPEED DRIVES S15 (HEAVY DUTY)L O W V O L T A G EEXTREME PERFORMANCE MICRO-DRIVECOMMUNICATION OPTIONS The S15 drive offers a wide array of easily installed option boards. These boards allow the user to communicate with a wide variety of systems . Options include:ADVANCED FEATURES FOR MAXIMUM DRIVE PERFORMANCEBuilt-In LED Interface allows for quick, user-friendly programming and easy modification of the S15’s expanded parameter set. Additional remote-mount keypads are also available. The parameter write and simple fault tracking functionality of these optional keypads make setup and troubleshooting quick and simple.My Function , Toshiba’s Proprietary Programming Feature, allows the user to utilize logic-type programming without the expense of a micro PLC. The user is able to read all analog and digital inputs and outputs as well as monitor and compare data. When programmed in a user-defined logic sequence, the use of this data will allow for a higher level of process control not normally seen in an adjustable speed drive. These functions, along with timers, counters, and comparators, allow the S15 to not only meet but exceed performance expectations .S15’s Easy Key is a configurable key that simplifies startup and operation. The easy key quickly accesses commonly changed parameters. In addition, the easy key can also function as a simple local/remote key for easy operation switching.Improved PID Control Algorithm provides regulation of critical processes. High and low speed limits, deviation limits, online switching, and a built-in sleep function are included to enhance the flexibility and reliability of PID process control. Improved control is possible with the S15’s enhanced PID algorithm, making it easier than ever to dial in your process control application.Toshiba’s Proprietary Windows ®-Based ASD Pro Software is available at no additional cost. This easy-to-use software is designed to provide a full range of programming and monitoring tools for all Toshiba low voltage drives, including the S15. ASD Pro offers parameter reading, trending, and logging features that allow the user to save and transfer parameters and export data and graphs to an electronic file. Parameter groups and trending data can be easily converted into spreadsheets or graphs for field and validation reports.OTHER SPECIAL FEATURES ADDITIONAL OPTIONS The S15 can be supplied with additional options to expand control, allow greater flexibility, and provide better protection for a user’s application. Options include:• CANopen • D eviceNet • E therCAT • E thernet/IP • M odbus TCP • P rofibus DP • P ROFINET • S afe Torque Off (STO) Compliant • T en Year Long-Life Design • Rotary Encoder • R educed Energy Consumption • U L Listed & Labeled• Parameter Writer • I P54 Packaged Unit (Consult Factory)• I nput Reactor • D V/dt Long Lead Filter • N etPac™ Wireless Connection • R emote Mountable Keypads • D IN Rail Mounting essors mps FansLifts INDUSTRIES SERVED • Food & Beverage Processing • HVAC • Mining & Minerals • Oil & Gas • Water & Wastewater • Agribusiness APPLICATIONS • Blowers & Compressor • Machine Tools • Conveyors • Irrigation • Mixers • Pumps • Fans •© 2019 Toshiba International Corporation Motors & Drives Division 13131 West Little York Road Houston, Texas 77041 USA Tel +713-466-0277 US 1-800-231-1412 /ticTOSHIBA MOTORS & DRIVES DIVISIONAdjustable Speed Drives • Motors • Motor ControlsB-52 This diagram shows a standard wiring of the main circuit.Standard connection diagram – SINK (Negative) (common: CC)Main circuit power supply Braking resistor (Option) P0 PA/+ PB PC/- 3ph-240V class: three-phase 200-240V-50/60Hz1ph-240V class: single-phase 200-240V-50/60Hz3ph-500V class: three-phase380-480(UL)/500V - 50/60Hz3ph-600V class: three-phase 525V-600V- 50/60Hz Single phase powersupplyMCCB DC reactor (DCL)*2 (option)*1, *9 R/L1 S/L2 T/L3 Protective functionactivation output Low-speed signal output MCCB(2P)R/L1 S/L2/N Control power supply *5 VF-S15 Control circuit FLAFLBFLC Operation panel SW1 *6SINK SOURCEPLCRS485 connector SW2VIBPTC S4 S3 FM CC VIC VIB VIA PP RY RC Meter 1mA (or 0(4)-20mA/0-10V) External potentiometer (1k-10k Ω) (or voltage signal between VIA and CC: 0-10V) F R RES S1S2S3CC Forward run command Reverse run command Reset Preset-speed command 1 Preset-speed command 2 Preset-speed command 3 Common Speed reach Signal output Noise filter Power circuit Motor U/T1 V/T2 W/T3 MCurrent signal: 4(0)-20mAVoltage signal: 0-+10V (or -10-+10V) *3 *4 *4 STO+SU Ry *1: The T/L3 terminal is not provided for single-phase models. Use the R/L1 and S/L2/N terminals as input terminals. *2: The inverter is supplied with the PO and thePA/+ terminals shorted by means of ashorting bar.Before installing the DC reactor (DCL),remove the bar. *3: When using the OUT output terminal in sink logic mode, short the NO and CC terminals. *4: When VIA or VIB terminal is used as logic input terminal, refer to section 7.2.1. *5: When backing up the control power supply, an external DC24V power supply is required. When using a communication option with theexternal DC24V power supply, add a diodebetween the external DC24V power supplyand +SU terminal. (Diode rating: 400V –1.5A or more)Refer to section 2.3.2. *6: Set the slide switch SW1 to SINK side.Refer to section 2.3.2 for details.Default setting is PLC side. *7: When STO terminal is used as compliancewith safety standards, refer to Safetyfunction manual (E6581860).*8: Calibration is needed before using themeter. Refer to section 5.1.*9: When using 600V class, be sure to connectan input reactor (ACL). *10: 600V class have no built-in noise filter.*7 P24OUT NO CC *8*10B-62Standard connection diagram – SOURCE (Positive) (common: P24)Main circuit power supplyBraking resistor (Option)P0 PA/+ PB PC/-3ph-240V class: three-phase 200-240V-50/60Hz1ph-240V class: single-phase 200-240V-50/60Hz3ph-500V class: three-phase380-480(UL)/500V - 50/60Hz3ph-600V class: three-phase 525V-600V- 50/60HzSinglephasepowersupplyMCCBDC reactor (DCL)*2 (option)*1, *9R/L1S/L2T/L3Protective functionactivation outputLow-speedsignal outputMCCB(2P)R/L1S/L2/NControl powersupply*5VF-S15 ControlcircuitFLAFLBFLCOperation panelSW1 *6SINK SOURCEPLC RS485connectorSW2VIBPTCS4S3FM CC VIC VIB VIA PPRYRCMeter1mA(or 0(4)-20mA/0-10V)External potentiometer (1k-10kΩ)(or voltage signal between VIA and CC: 0-10V)FRRESS1S2S3P24Forward run commandReverse run commandResetPreset-speed command 1Preset-speed command 2Preset-speed command 3CommonSpeed reachSignal outputNoisefilterPower circuitMotorU/T1V/T2W/T3MCurrent signal: 4(0)-20mAVoltage signal: 0-+10V(or -10-+10V)*3*4 *4STO+SUCCRy*1: The T/L3 terminal is not provided forsingle-phase models.Use the R/L1 and S/L2/N terminals asinput terminals.*2: The inverter is supplied with the PO andthe PA/+ terminals shorted by means ofa shorting bar.Before installing the DC reactor (DCL),remove the bar.*3: When using the NO output terminal insource logic mode, short the P24 andOUT terminals.*4: When VIA or VIB terminal is used aslogic input terminal, refer to section7.2.1.*5: When backing up the control powersupply, an external DC24V power supplyis required. When using acommunication option with the externalDC24V power supply, add a diodebetween the external DC24V powersupply and +SU terminal. (Diode rating:400V – 1.5A or more)Refer to section 2.3.2.*6: Set the slide switch SW1 to SOURCEside.Refer to section 2.3.2 for details.Default setting is PLC side.*7: When STO terminal is used ascompliance with safety standards, referto Safety function manual (E6581860).*8: Calibration is needed before using themeter. Refer to section 5.1.*9: When using 600V class, be sure toconnect an input reactor (ACL).*10: 600V class have no built-in noise filter.*7OUTNOCC*8*10。
新力川伺服驱动说明书
请将接地端口连接到100Ω以下的接地，接地不良可能会造成触电或火灾。
请勿连接三相电源至U、V、W马达输出端口，否则可能会造成人员受伤或者导致火灾。
请锁紧电源与马达输出端口的默写螺丝，否则可能会因为接触短路造成爆炸引起火灾。
操作注意
当机械设备开始运行前，须配合其使用者参数调整设定值。若未调整到相符的正确设定值，可能会导致机械设备运行失去控制或发生故障。
维护或检查人员
在使用前，请您仔细详读本手册以确保使用上的正确。此外，请将它妥善保存在安全的地点以便随时查阅。下列在您尚未读完本手册时，务必遵守事项：
安装的环境必须没有水气，腐蚀性气体或可燃性气体。
接线时，禁止将三相电源接至马达U、V、W的连接器，因为一旦接错时将损坏伺服驱动器。
接地工程必须确实实施。
LCDA系列可使用于工业应用场合上，且建议安装于使用手册中的配线（电）箱环境（驱动器、线材与电机都必须安装于符合环境等级的安装环境最低要求规格）。
在按收检验、安装、配线、操作、维护与检查时，应随时注意以下安全注意事项。
标志[危险]、[警告]与[禁止]代表的含义：
意指可能潜藏危险，若未遵守要求可能会对人员造成严重伤或致命
即使关闭电源，伺服驱动器内部仍可能会滞留高电源，请暂时（20分钟内）不要触摸电源端口。并确认D1电源指示灯完全熄灭后，再进行检查作业。
请勿频繁地开关电源。若需要连续开关电源时，请控制在5分钟一次以下。
主电路端口座配线
端口座的一个电线插入口，请仅插入一根电线。
在插入电线时同，请不要使芯线与邻近的电线短路。
标高
海拔1000m以下
海拔1000m以下
振动
小于0.5G（4.9m/s2）10 Hz -60Hz（非连续运行）
SL1500电控系统说明书
SL1500系列风力发电机组电控系统说明书华锐风电科技有限公司2007年6月第2版目录前言 (4)第一章 SL1500 风机电控系统简介 (9)1.1 SL1500风力发电机组电控系统的组成 (9)1.2 SL1500风力发电机组电控系统的主要特点 (9)第二章 SL1500 风机电源系统 (10)2.1 箱式变压器参数 (10)2.2 辅助变压器的参数 (10)2.3 箱式变电站的系统图 (11)第三章 SL1500 变速恒频控制系统 (12)3.1 双馈异步发电机 (12)3.1.1 介绍 (12)3.1.2 风机电能的模型 (12)3.1.3 技术条件 (15)3.2 变频器 (16)3.2.1 整套的转换器系统组成 (16)3.2.2 特征电气参数 (16)3.2.3 变频器系统的连接图 (17)3.3 传感器 (19)3.4 其他功能 (19)第四章 SL1500 偏航控制系统 (20)4.1 介绍 (20)4.1.1 偏航驱动系统 (20)4.1.2 制动器是盘式制动器 (20)4.1.3 限位保护 (20)4.2 电机参数 (20)4.3 制动器参数 (21)4.4 偏航变频器 (21)第五章 SL1500 变桨控制系统 (22)5.1 变桨系统介绍 (22)5.2 变桨齿轮箱 (22)5.3 变桨电气系统 (23)5.3.1 变桨电动机 (23)5.3.2 变桨变频器 (23)5.3.3 电池系统 (23)5.3.4 传感器 (24)5.4 雷电保护 (24)5.5 控制接口 (24)5.5.1 软件接口 (24)5.5.2 硬连线信号 (24)5.5.3 软件 (25)第六章 SL1500 PLC控制系统 (26)6.1 PLC控制系统描述 (26)6.2 PLC程序结构 (26)第七章 SL1500 风机的保护 (27)7.1 防雷保护系统 (27)7.2 接地系统保护 (27)7.3 电路及控制保护系统 (28)第八章 SL1500风机主要配件 (29)8.1 轮毂滑环简介 (29)8.1.2 电气性能 (29)8.1.3 加热 (29)8.2 WT502操作屏 (30)8.2.1 说明 (30)8.2.2 正视图 (30)8.2.3 按钮描述 (30)附件1 主要控制柜的主要内容及功能介绍 (32)附件2 电气原理图纸 (33)附件3 互连接线表 (33)附件4 电气故障清单 (33)本文件基本信息：本文件修改信息：本文件所涉及的参考文件：前言SL1500风力发电机组采用变桨矩、变速恒频等技术，是当今世界风力发电最先进的技术代表，具有发电量大、发电品质高、结构紧凑等优点。
金城圣甲虫150说明书
金城圣甲虫150说明书金城圣甲虫150自动洗衣机分为波轮的滚筒两种，使用方法如下：1、金城圣甲虫150全自动波轮洗衣机连接好电源，保证你家的电源线路安装漏保和接地，否则可能发生严重的触电事故。
还有就是安装好自动水龙头，保证地面平稳。
把要洗涤的衣物和洗衣粉及添加剂（软化剂、漂白剂等）故入洗衣机内，并将机盖关上。
1）你需要启动电源按钮，让洗衣机可以接受控制。
2）根据需要洗涤衣物的多少加水量。
3）选择洗衣流程：有浸泡、洗涤、漂洗、脱水四个流程。
可以根据自己的需要做出选择。
当你做出选择时，相应的过程指示灯就会亮，它亮多少个，说明它这些程序都要做，如果按到脱水，说明它只完成脱水程序，其他一概不动．你每按一下按钮它就会有相应的程序。
4）还有标准和柔和选项，这个是指洗衣的力度，快速还是慢速，这是指洗衣的时间长短。
5）按一下开始按键洗衣机就按照你的指定要求自动完成全部洗衣过程。
2、金城圣甲虫150全自动滚筒洗衣机相对于波轮产品，滚筒洗衣机不止在洗衣原理上与波轮洗衣机不同，滚筒洗衣机的操作模式大相径庭。
当然首先也是先放进衣服和洗衣粉，打开电源再调好洗衣程序，按开始键开始洗涤，不过相对于波轮式洗衣机。
滚筒洗衣机在使用的过程中有一些注意事项：（1）放好衣物之后，电脑根据衣物的多少会自动控制水量，水够了以后上水自动停止。
洗衣的时间是不可以自定义的，洗的是什么材料的衣物，就选到那个挡位。
（2）滚筒洗衣机一定要使用低泡洗衣粉，并且量要非常少，用量过多时会产生泡沫，泡沫会从门圈和皂盒中溢出，洗衣机会发出警报，所以只要使用低泡洗涤剂并减少洗涤剂的用量就可以解决。
（3）滚筒洗衣机洗衣服时，可能看不到水流，这是因为滚筒洗衣机的洗涤原理是靠摔打，当水量过多时不仅浪费水，还无法形成有效的摔打。
但在漂洗时会增加水量，所以不用担心最终的洗净效果。
金城圣甲虫150滚筒洗衣机怎么用洗衣的预备滚筒洗衣机的料盒有三个槽，从左至右分别用于投放主洗剂、柔顺剂和预洗剂。
智能优势动力系统ISX15和Fuller优势系列自动挡转速箱说明书
SmartAdvantage™Powertrain ISX15 And Fuller Advantage® Series Automated Transmission The Most Fuel-Efficient Powertrain You Can Buy.2%3-6%ADEPT ™ with SmartCoast ™Downspeeding,Combustion Improvement and Reduced ParasiticLossesSmartAdvantage Powertrain20142015Since its introduction in 2013, the SmartAdvantage ™ Powertrain has proven to be the most fuel-efficientpowertrain in the trucking industry. Continuous improvements and innovative technology have yielded significant gains every year. Today we are utilizing downspeeding to get up to 7% better fuel economy than competitive integrated powertrains.To get the highest mpg possible, the SmartAdvantagePowertrain is configured using Cummins ISX15 engine with SmartTorque2 (ST2) and the SmartCoast ™ option, pairedIn response to customer needs, Cummins and Eaton have expanded the ISX15 SmartAdvantage Powertrain lineup to include the original small-step overdrive transmission, plus a new direct drive version that delivers exceptional fuel economy in less-than-truckload (LTL) and regional linehaul operations. This addition will help fleets achieve productivity challenges across a broader spectrum of operating conditions with specific duty cycles.The ISX15 SmartAdvantage Powertrain is the only integrated powertrain in the industry to offer bothsmall-step overdrive and direct drive options. This choice allows trucking fleets to spec the best ratio for their application, cruise speed and terrain.More Ways More Trucking Fleets Can Save More Fuel.The Power Of Choice: Overdrive Or Direct Drive.with an Eaton Fuller Advantage ® 10-speed automated manual transmission (AMT). The engine and transmission share critical data, determining the torque required to deliver the power level that drivers demand.The ISX15 SmartAdvantage Powertrain optimizes shifting based on grade, vehicle weight, engine torque and throttle position. The result is error-free, guess-proof shifting, making every driver in your fleet as efficient as your best driver.When you spec the ISX15 SmartAdvantage Powertrain, you can choose between a small-step overdrive or direct drive Eaton Fuller Advantage10-speed automated transmission. Small-Step Overdrive technology combines downspeeding in overdrive (10th gear) with efficiency in direct drive(9th gear). A 26% step from 9th to 10th allows the transmission to move quickly and seamlessly between the two upper gears, in response to changing terrain and load demand. Customers benefit from downspeeding (cruising at a lower rpm for better fuel economy) through fully integrated electronic control of the engine and transmission as a complete unit. This will be the optimal choice for about 80% of North American linehaul trucking fleets.Direct Drive has a 1:1 gear ratio in 10th gear. This reduces friction losses, delivering up to as much as 4% better fuel economy than small-step overdrive transmissions when operating on flat terrain with an average road speed not exceeding 62 mph. About 20% of trucking fleets fit this profile. The SmartAdvantage Powertrain with direct drive has recently been approved for 2.26, 2.28 and 2.39 axle ratios,providing additional downspeeding for enhanced efficiency.The Eaton Fuller Advantage 10-speed automated transmission makes strategic use of lightweight components to reduce weight and increase payload by82 lb. Precision Lubrication technology eliminates theoil cooling system, uses 33% less oil than conventional transmissions while further enhancing fuel economy. Cummins is continually setting new benchmarks for the trucking industry. Major technological advancements in the ISX15 platform include ADEPT™ with SmartCoastand SmartTorque2, along with Vehicle Acceleration Management.n S T2 automatically senses vehicle weight, grade and operating gear, and then selects the optimum torque for the best fuel economy and performance in every gear. Higher torque is delivered earlier in the rpm range, so you can cruise at 1150-1240 rpm and still get the torque and power needed to match real-time load demand.n S martCoast is an optional feature within the ADEPT suite of Cummins electronic engine features that senses when a vehicle is descending downhill (up to 4% grade), then disengages the driveline to take full advantage of gravity and momentum.W hen SmartCoast is active, the ISX15 returns to idle. In routes across hilly terrain, this feature together with ST2, can save [up to 3%] in fuel economy.n V AM maintains a smoother acceleration rate from the launch of the vehicle, maintaining a more consistent acceleration due to more efficient transition through the gears. This enhances the driving experience and reduces driveline wear while increasing fuel economy.Technology To Match Your Duty Cycle. Where Innovation Meets Integration.Direct DriveSmall Step≤62 mph average cruising speedHillyMountainous ≥63 mph average cruising speedWhether you run coast-to-coast at 80,000 lb, or stay close to home and make multiple stops on everyroute, there’s a SmartAdvantage ™ Powertrain that can help you reduce fuel use and lower your total cost of operation while maintaining road speeds and driver (800) 826-4357.Cummins Base Warranty for the ISX15 engine is 2 years/ 250,0000 miles (402,336 km), and includes parts and labor on warrantable failures for the engine andaftertreatment system, with no deductible. A wide range of extended coverage plans are available.Spec’ing To Win.The key is to spec your ISX15 SmartAdvantagePowertrain at the ideal horsepower and torque rating with the proper Eaton Fuller Advantage 10-speed automated transmission, utilizing the correct axle ratio and tires to deliver driver-pleasing performance with the best possible fuel economy.To learn more about the ISX15 SmartAdvantage Powertrain, call your local Cummins or Eaton Fuller representative, or check out our website at .Cummins Inc. Box 3005Columbus, IN 47202-3005 U.S.A.Phone: 1-800-DIESELS™ (1-800-343-7357)Internet: T /CumminsEngines /CumminsEnginesBulletin 4971525 Printed in U.S.A. 11/15©2015 Cummins Inc.EatonVehicle Group P .O. Box 4013Kalamazoo, MI 49003 USA 800-826-HELP (4357)/roadranger TRSL2529 1115。
M15 电子琴 用户说明书
注意事项请在操作使用前，首先仔细阅读以下内容 。
请将本使用手册妥善保管，以便将来随时查阅。
电源请将指定的电源适配器连接到一个电压正确的电源插座。
请勿使用电压与设备不匹配的电源。
设备不使用时，或在雷雨暴风期间，请断开电源。
连接在将本设备连接到其他设备之前，请关闭所有设备的电源开关。
这将有效防止设备故障或防止损坏其他设备。
位置请勿将设备放置于以下环境中，以免设备发生变形、变色或其他更严重的损害：阳光直射处、暖气旁多尘土、高温、高湿、可能产生强烈震动或冲击的位 置接近磁场处对其他设备的干扰将此设备放置在电视机、收音机的周围可能引起干扰。
使用此设备时，请与电视机和收音机保持适当的距离。
维护保养只能使用柔软的干布清洁此设备。
请勿使用涂料稀释剂、溶剂、清洁液或浸了化学物质的抹布。
处理请勿对开关或控制按钮用力过猛。
避免纸张、金属或其他杂物进入设备内部。
如果发生此类情况，请拔掉墙上电源插座中的插头。
然后请具有资格的维修人员对设备进行检查。
在移动设备之前，请断开所有的电源。
警告该产品的正常功能可能会遭受强电磁干扰。
如果出现这种情况，只需简单地按照用户手册将产品恢复初始设置。
当产品的功能无法恢复时，请在其他位置使用本产品。
装箱单尊敬的用户，当您选购本乐器后，请检查以下物品是否齐全： 琴体 外接电源琴谱架 说明书售后保修证书面板控制及显示说明前面板4后面板..........................................................................4显示.............................................................................5设置电源供电 (6)连接连接脚踏板...................................................................7连接耳机......................................................................7连接到音频设备...........................................................7连接麦克风...................................................................7连接到计算机...............................................................7播放示范曲...................................................................8演奏各种乐器音色选择并演奏音色(主音色)..............................................8演奏两种音色(双音色)..................................................8力度响应......................................................................9延音效果......................................................................9弯音效果......................................................................9数码效果......................................................................9移调设置....................................................................10八度设置....................................................................10演奏各种风格伴奏选择自动伴奏.............................................................11演奏插入段落.............................................................11演奏前奏/尾声段落.....................................................11同步启动....................................................................12渐强/渐弱...................................................................12伴奏音量设置. (12)..........................................................................速度控制12自动低音和弦.............................................................13单触键设置.................................................................14面板设置储存面板设置储存 (15)和弦字典 (15)节拍器打开节拍器.................................................................16节拍设置....................................................................16播放及控制歌曲欣赏歌曲....................................................................17学习模式....................................................................17录音及回放.................................................................18MIDI 功能什么是MIDI ?..............................................................19MIDI 连接....................................................................19故障排除....................................................................20技术规格....................................................................20附录音色一览表.................................................................21节奏一览表.................................................................23歌曲一览表.................................................................25和弦类型表.................................................................26MIDI 应用表. (27)....................................................................后面板6. 插入/主奏按钮B插入变奏，同时改变成主奏B 。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1.概述.1.1 产品特点:EBZ150A(S150JA)掘进机是在EBZ150(S150J)掘进机基础上升级开发设计的一种中型掘进机，整机具有以下特点:(1).截割部可伸缩，伸缩行程为550mm，内喷雾为后喷雾；(2).具有内、外喷雾，强化外喷雾，合理设计外喷雾形式；(3).内喷雾具有漏水检查设置；(4).铲板底部大倾角，整机地隙大，爬坡能力强；(5).中间运输机平直结构，与铲板搭接顺畅，龙门高、运输通畅；(6).本体、后支承箱体形式焊接结构，刚性好，可靠性高；(7).液压系统采用恒功率、压力切断、负载敏感控制；(8).电气系统采用新型综保，具有液晶汉字动态显示功能；(9).重心低，机器稳定性好。
1.2 主要用途及适用范围:该机主要用于煤岩硬度≤6.5的煤巷、半煤岩巷以及软岩的巷道、隧道掘进，能够实现连续切割、装载、运输作业。
最大定位截割断面24m2，最大截割硬度≤65Mpa，纵向工作坡度≤±16°执行标准: MT238-1991 悬臂式掘进机通用技术条件Q/JC-01-2006 EBZ150A（S150JA）掘进机产品标准1.3 产品型号、名称和型号含义1.3.1 名称: EBZ150A（S150JA）掘进机1.3.2 型号含义:E B Z 150 A (S150JA)系列化改进型截割电机功率KW纵轴式悬臂式掘进机1.4 使用环境条件EBZ150A（S150JA）在下列条件下可正常工作(1). 海拔不超过2000m;(2). 环境温度-20℃～+40℃;(3). 周围空气相对湿度不大于90%(+25℃);(4). 在有瓦斯、煤尘或其他爆炸性气体环境矿井中；(5). 与垂直面的安装斜度不超过16°；(6). 无破坏绝缘的气体或蒸气的环境中；(7). 无长期连续漏水的地方；(8). 污染等级：3级(9). 安装类别：Ⅲ类1.5 安全保护:EBZ150A（S150JA）具有下列安全保护性能:(1). 掘进机电控设备的设计、制造符合GB3836.1、GB3836.2和《煤矿安全规程》2004版规定；(2). 所有安标受控配套件均取得煤矿安全标志证；(3). 掘进机设有起动报警装置和前后照明灯；(4). 掘进机设有制动系统及防滑保护装置；(5). 截割机构和装运机构设有过载保护装置；(6). 油泵电机和截割电机、二运电机之间启、停顺序，在电控系统中有闭锁装置；(7). 液压系统有过滤装置，还设有压力、油温、油位显示等保护装置；(8). 电控系统设有紧急切断和闭锁装置，在司机座位另一侧还装有紧急停止按钮；(9). 掘进机设有内、外喷雾系统，并有过滤装置、漏水检测及保护功能。
2. EBZ150A（S150JA）掘进机结构特征与工作原理2.1 总体结构及工作原理本掘进机由截割部、铲板部、第一运输机、本体部、行走部、后支承、液压系统、水系统、润滑系统、电气系统构成，总体结构见图1(第3页),液压原理见图2（第4页）图1 总图图2 液压原理图2.2 主要部件的结构作用及工作原理2.2.1 截割部由截割头、伸缩部、截割减速机、截割电机组成，见图3图3 截割部2.2.2 截割头为圆锥台形，在其圆周螺旋分布41把截齿。
截割头通过花键套和2个M30的高强度螺栓与截割头轴相联，使主轴带动截割头旋转，见图4图4 截割头2.2.3 伸缩部位于截割头和截割减速机中间，通过伸缩油缸使截割头具有550mm的伸缩行程，见图5图5 伸缩部2.2.4截割减速机是两级行星齿轮传动，它和伸缩部用26个M24的高强度螺栓相联。
见图6图6 减速器2.2.5 截割电机为双速水冷电机，使截割头获得2种转速，它与截割减速机通过定位销和25个M24的高强度螺栓相联2.3 铲板部铲板部是由主铲板、侧铲板、铲板驱动装置、从动轮装置等组成。
通过两个液压马达带动弧形三齿星轮，把截割下来的物料装到第一运输机内。
2.3.1 铲板宽度为2.9m，由主铲板、侧铲板组成，用高强度螺栓连结，铲板在油缸作用下可向上抬起342mm，向下卧底356mm。
见图7。
2.3.2 铲板驱动装置是通过同一油路下的二个控制阀各自控制一个液压马达，对弧形三齿星轮进行驱动，并能够获得均衡的流量，确保星轮在平稳一致的条件下工作，提高工作效率，降低故障率。
驱动装置见图8。
图7 铲板部图8 铲板部驱动装置2.4 第一运输机第一运输机位于机体中部，是边双链刮板式运输机。
运输机分前溜槽、后溜槽。
前、后溜槽用高强度螺栓联接，运输机前端通过插口与铲板和本体销轴相连，后端通过高强度螺栓固定在本体上。
采用二个液压马达直接驱动链轮，带动刮板链组实现物料运输。
张紧装置采用丝杠加弹簧缓冲的结构，对刮板链的松紧程度进行调整。
驱动装置见图9，第一运输机见图11（见第8页）。
图9 第一运输机驱动装置2.5 本体部本体部位于机体的中部，是以厚钢板为主材焊接而成。
本体的右侧装有液压系统的泵站，左侧装有操纵台，前面上部装有截割部，下面装有铲板部及第一运输机。
在其左、右侧下部分别装有行走部,后部装有后支承部。
本体部见图10图10 本体部图11 第一运输机2.6 行走部行走部主要由定量液压马达、减速机、履带链、张紧轮组、张紧油缸、履带架等几部分组成。
定量液压马达通过减速机及驱动轮带动履带链实现行走。
支重形式采用滑动摩擦式。
2.6.1履带张紧机构是由张紧轮组和张紧油缸组成，履带的松紧程度是靠张紧油缸推动张紧轮组来调节的。
张紧油缸为单作用形式，张紧轮伸出后靠卡板锁定。
张紧油缸、卡板均在履带外测安装，方便实用，并均配有盖板以保证外形的美观。
2.6.2行走减速机用高强度螺栓与履带架联接。
履带架采用挂钩及一个竖平键与本体相联，用12个M30高强度螺栓紧固在本体的两侧。
行走部见图12图12 行走部2.7 后支承后支承的作用是减少在截割时机体的振动，提高工作稳定性并防止机体横向滑动，见图13。
在后支承支架两边分别装有升降支承器，利用油缸实现支承。
后支承支架用M24的高强度螺栓通过键与本体相联，后支承的后部与第二运输机联接。
电控箱、泵站都固定在后支承支架上。
图13 后支承2.8 液压系统液压系统是由油缸（包括：截割头升降油缸、截割头回转油缸、铲板油缸、后支承油缸、履带张紧油缸）、马达（包括：行走、运输、内喷雾马达）、操纵台、泵站以及相互联接的油管等组成。
各图见《EBZ150A（S150JA）掘进机装配图册》。
液压原理图见图2。
2.8.1 液压系统的功能(1). 行走马达驱动；(2). 星轮马达驱动；(3). 第一运输机马达驱动；(4). 内喷雾泵马达驱动；(5). 截割头的上、下、左、右、前、后移动；(6). 铲板的升降；(7). 后支承器的升降；(8). 履带的张紧；(9). 为锚杆机提供两个动力接口；2.8.2 油泵、液压马达和油缸泵站是由75KW电机驱动，组合变量油泵，通过油管和阀组，将压力油分别送到截割部、铲板部、第一运输机、行走部、后支承的各液压马达和油缸。
本机共有11个油缸，截割头升降油缸2个、铲板升降油缸2个，截割头回转油缸2个，后支承器的升降油缸2个，以上油缸均设有安全型平衡阀,截割头伸缩油缸1个，履带张紧油缸2个。
2.8.3 操纵台操纵台上装有换向阀,压力表，通过操作手柄完成各油缸及液压马达的动作，通过压力表开关的不同位置可以分别检测各回路油压状况。
2.8.4 油缸和马达的过负荷保护为防止油缸和马达过负荷而造成的损坏，液压系统有过载保护功能。
2.9 水系统水系统分内、外喷雾水路。
外来水经一级过滤后分为二路，第一路经进水直接通往喷水架，由雾状喷嘴喷出，第二路经二级过滤、减压、冷却（冷却液压系统用油）再分为二路，一路经截割电机（冷却电机）后喷出。
另一分路经水泵加压（3MPa）后，由截割头内喷出，起到冷却截齿及灭尘作用。
注意：截割头截割前，必须启动内喷雾，否则喷嘴阻塞，影响灭尘效果。
3. 技术特征3.1 整机参数3.1.1 型号：EBZ150A（S150JA）总体长度( m)： 9.30总体宽度(m)： 2.90总体高度(m)： 1.65总重 (t)： 42卧底深度(m)： 0. 216爬坡能力：±16°截割硬度(Mpa)：≤653.1.2 截割范围：高度(m)： 4.8宽度(m)： 5.5面积(m2 ): 243.1.3 截割部截割头形状：圆锥台形截割头转速(r/mim)： 46/23电动机： YBUD-150/80-4/8 隔爆水冷型 1台喷雾：内、外喷雾方式3.1.4 铲板部装载形式：弧形三齿星轮式装载宽度（m）： 2.90星轮转数（r/min）: 33装载能力m3/min（最大）: 4.2原动机(KW)：液压马达 10KW/台 2台3.1.5 第一运输机形式：边双链刮板式溜槽断面尺寸 (mm)： 540(宽)³370（高）链速m/min： 61张紧形式：弹簧、丝杠张紧运输能力m3/min： 6.0原动机KW：液压马达 10KW/台 2台3.1.6 行走部形式：履带式履带板宽度(mm)： 520制动方式：一体式多片制动器（减速机内置）对地压强（Mpa）： 0.14行走速度(m/min)： 0～6张紧形式：油缸张紧、卡板锁紧原动机（KW）液压马达+减速机 17KW/台各2台3.1.7 液压系统系统压力（Mpa） 18柱塞变量双泵(ml/r): A11VO130/130 1台液压马达排量行走部(ml/r): A2FE125 2台铲板部 (ml/r): IAM1200 .H4 2台第一运输机部 (ml/r): IAM400 .H2 2台油箱容量(L)： 500油泵电动机： YBU-75 隔爆风冷 1台换向阀：手动式 2组油冷却器: 水冷却式 1台3.1.8 水系统外来水量（L/min）： 100外喷雾水压(Mpa): 1.5内喷雾水压(Mpa): 3.03.2.电气部分:主回路：额定电压： AC1140/660V额定电流：≤300A额定频率： 50HZ输出分路数： 4路额定功率： 236KW3.2.1 截割电机型式：掘进机用隔爆型三相异步电动机水冷式规格型号： YBUD-150/80-4/8 绝缘等级:H级工作方式:S1 额定电压： AC1140/660V 双速Y/△额定电流：高速：90A/156A 低速：60A/104A3.2.2 油泵电机型式：掘进机用隔爆型三相异步电动机风冷式规格型号： YBU-75 绝缘等级：H级工作方式：S1额定电压： AC1140/660V Y/△额定电流： 47.1A/81.5A3.2.3 截割急停、总急停按钮型式：矿用隔爆型规格型号： BZA1-10/24-1ZS 附带锁紧装置额定电压： DC24V额定电流： 10A 内部按钮为常开用途：总急停按钮：用于紧急停机截割急停按钮：用于截割电机停止3.2.4 电铃：型式：矿用隔爆型规格型号： BAL1-36/127-150额定电压： AC127V额定电流： 0.35A用途：开机信号，启动报警3.2.5 照明灯： 3盏型式：矿用隔爆型规格型号： DGY35/24B额定电压： AC 24V额定电流： 3A3.2.6 电气控制部分相关参数详见《EBZ150A（S150JA）悬臂式掘进机电气系统使用说明书》4. 各部的安装与调整4.1 安全警示4.1.1有安全及防爆性能要求的外配套产品，必须按《EBZ150A（S150JA）安全标志控制件明细表》中所列配套厂家进行选配；4.1.2电气装置必须按其各处警示牌“严禁带电开盖”要求进行操作；4.1.3液压系统所有液压元件及接合处，严禁在泄漏状态下工作。