发动机中英文术语

汽车发动机专业术语

汽车发动机专业术语发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V 形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engine W形发动机w-engine I形发动机I-engine L形发动机L-engine F形发动机F-engine。

发动机性能术语英汉对照

发动机性能术语英汉对照（1）Two-stroke cycle 二冲程循环Four-stroke cycle 四冲程循环Diesel cycle 狄塞尔循环Otto cycle 奥托循环Mixed cycle 混合循环Constant volume cycle 定容循环Constant pressure cycle 等压循环Working cycle 工作循环Ideal cycle 理想循环Thermodynamic cycle 热力循环Stroke 冲程，行程Piston stroke 活塞行程Long stroke 长行程Up stroke 上行程Down stroke 下行程Intake stroke 吸气行程Charging stroke 充气行程Compression stroke 压缩行程Working stroke 工作行程Explosion stroke 爆炸行程Expansion stroke 膨胀行程Power stroke 动力行程Exhaust stroke 排气行程Expansion-exchange stroke 膨胀-换气行程Exchange-compression stroke 换气-压缩行程Dead center 止点Top dead center 上止点Lower dead center 下止点Before top dead center 上止点前After top dead center 上止点后Before bottom dead center 下止点前After bottom dead center 下止点后Cylinder bore 缸径Bore and stroke 缸径与冲程Air-cell 空气室Cylinder clearance volume 气缸余隙容积Combustion chamber volume 燃烧室容积Maximum cylinder volume 气缸最大容积Compression chamber 压缩室Displacement (swept volume) 排气量Engine displacement 发动机排量Piston displacement 活塞排量Cylinder capacity 气缸容量Single-chamber capacity 单室容量Volumetry 容积法Compression ratio 压缩比Critical compression ratio 临界压缩比Expansion ratio 膨胀比Surface to volume ratio 面容比Stroke-bore ratio 行程-缸径比Mixture ratio 混合比Compression pressure 压缩压力Brake mean effective pressure (BMEP) 制动平均有效压力Air fuel ratio 空燃比Fuel air ratio 燃空比Fuel equivalence ratio 燃料当量比Torque 扭矩Power per cylinder 单缸功率Power per liter 升功率Torque per liter 升扭矩Mass per liter 升质量Derating power 减额功率Output power 输出功率Gross power 总功率Net power 净功率Fuel consumption 燃油消耗量Specific fuel consumption 比燃料消耗量Air consumption 空气消耗量Oil consumption 机油消耗量Rated power 额定功率Brake power 制动功率Brake thermal efficiency 制动热效率Indicted thermal efficiency 指示热效率Overall efficiency 总效率Smoke limiting power 排烟极限功率Power curve 功率曲线Mechanical loss 机械损失Mechanical efficiency 机械效率Effective thermal efficiency 有效热效率Volumetric efficiency 容积效率Excess air coefficient 过量空气系数Adaptive coefficient 适应性系数Torque adaptive coefficient 扭矩适应性系数Speed adaptive coefficient 转速适应性系数Intensification coefficient 强化系数Correction factor 校正系数Conversion factor 换算系数Mean piston speed 活塞平均速度Engine speed 发动机速度Idling speed 怠速转速Economic speed 经济转速Starting speed 起动转速Lowest continuous speed with load 最低稳定工作转速Lowest idling temperature 发动机怠速转动最低温度Maximum torque speed 最大转矩转速Maximum noload governed speed 受控最高空转转速Speed governing调速Overspeed超速Idling怠速Speed fluctuation rate转速波动率Working condition (operating condition)工况Rated working condition额定工况Variable working condition变工况Steady working condition稳定工况No –load空载Full load 全负荷Over load 超负荷Part load 部分负荷Charge 充量（进气）Direction of rotation 旋转方向Clockwise 顺时针Anticlockwise 逆时针Left-hand rotation 左转Right-hand rotation 右转Major diameter 外径Pitch diameter 中径Minor diameter 内径Radial clearance 径向间隙Engine performance 发动机性能Loading performance 加载性能Starting performance 起动性能Acceleration performance 加速性能Power performance 动力性能Emission performance 排放性能No load characteristics 空转特性Partial throttle characteristics 负荷特性Governor control characteristics 调速特性Mapping characteristics 万有特性Steady-state speed governing rate 稳定调速率发动机性能专业术语英汉对照（2）Working medium 工质Practical cycle 实际循环Firing order 点火次序Timing 定时Stroke-bore ratio 行程缸径比Number of cylinders 气缸数Piston area 活塞面积Connecting rod length 连杆长度Crank radius 曲柄半径Crank radius-connecting rod length ratio 曲柄连杆比Working medium volume 气缸体积Piston swept volume 气缸工作体积Effective piston swept volume 气缸有效工作体积Cylinder clearance volume 气缸余隙体积Maximum cylinder volume 气缸最大体积Effective cylinder volume 气缸有效体积Engine swept volume 发动机排量Engine cylinder volume 发动机气缸总体积Clearance 余隙高度Injector protrusion 喷嘴端伸出量Intake process 进气过程Intake temperature 进气温度Intake pressure 进气压力Natural aspiration 自然进气Stratified charge 层状充气Intake advance angle 进气提前角Intake lag angle 进气迟后角Intake duration angle 进气持续角Intake swirl 进气涡流Intake turbulence 进气紊流Helical duct intake 螺旋进气道进气Tangential duct intake 切向进气道进气Masked inlet valve intake 导流屏进气Time-area value 时面值Valve lift 气阀升程Scavenging port area 气阀开度Gas exchange process 换气过程Scavenging process 扫气过程Scavenging duration 扫气持续期Scavenging pressure 扫气压力Uniflow scavenging 直流扫气Loop scavenging 回流扫气Cross scavenging 横流扫气Crankcase scavenging 曲轴箱扫气Scavenging by blower 扫气泵扫气Piston underside pump scavenging 活塞底泵扫气Exhaust-pulse scavenging 排气脉冲扫气Coefficient of scavenging 扫气系数Trapping efficiency 扫气利用系数Scavenging efficiency 扫气效率Coefficient of scavenging loss 扫气漏失系数Delivery ratio 给气比Valve timing 配气定时Valve overlap 气阀重叠Swirl rate 涡流比Compression process 压缩过程Compression pressure 压缩压力Compression beginning pressure 压缩始点压力Compression beginning temperature 压缩始点温度Compression end pressure without combustion 压缩终点压力Compression end temperature without combustion 压缩终点温度Fuel injection starting compression pressure 喷油始点压缩压力Ignition starting compression pressure 着火始点压缩压力Ratio of pressure rise 压力升高比Effective compression ratio 有效压缩比发动机性能专业术语英汉对照（3）Polytropic index of compression 压缩多变指数Compression swirl 压缩涡流Injection process 喷油过程Direct injection 直接喷射Indirect injection 间接喷射Electronic-controlled injection 电控喷射Fuel supply advance angle 供油提前角Fuel injection advance angle 喷油提前角Injection lag 喷油延迟角Injection duration 喷油持续角Nozzle hole area 喷孔面积Total area of nozzle holes 喷孔总面积Ratio of nozzle hole length-nozzle hole diameter 喷孔长径比Nozzle hole cone 喷孔锥体Nozzle hole cone angle 喷孔锥角Needle lift 针阀升程Sac volume 针阀压力室体积Retraction volume of delivery valve 出油阀卸载体积Injection pressure 喷油压力Injection starting pressure 启喷压力Injection peak pressure 喷油峰值压力Inject back pressure 喷油背压Spray 喷注Spray penetration 喷注贯穿距离Spray penetration curve 喷注贯穿规律Spray penetration ratio 喷注贯穿率Fuel delivery per cycle per cylinder 循环喷油量Minimum fuel delivery per cycle per cylinder 最小循环喷油量Fuel supply rate 供油率Fuel injection rate 喷油率Accumulated fuel delivery rate 累计喷油率Fuel supply rate curve 供油规律Fuel injection rate curve 喷油规律Fuel delivery curve at constant speed 喷油泵负荷特性Fuel delivery curve at fixed rack 喷油泵速度特性Nozzle flow characteristic 喷嘴流通特性Nozzle hydrokinetic characteristic 喷嘴液力特性Spray characteristic 喷雾特性Spray cone angle 喷雾锥角Atomization 雾化Sauter mean diameter (SMD) 索特平均直径Abnormal injection 异常喷油Secondary injection 二次喷油Fluctuating injection 波动喷油Intermittent injection 间断喷油Disorder injection 不齐喷油Nozzle dribbing 喷油滴漏Mixture formation process 混合气形成过程Mixture concentration 混合气浓度Mixture ratio 混合比Volumetric mixture ratio 体积混合比Mole mixture ratio 摩尔混合比Theoretical mixture ratio 理论混合比Theoretical mixture gas 理论混合气Film mixture 油膜混合Combustible mixture 可燃混合气Total air-fuel ratio 总空燃比Total excess air ratio 总过量空气系数Air untilization ratio 空气利用系数Chamber mixture 雾化混合Compound mixture 复合混合Peripheral mixture 周边混合Thermo-mixture effect 热混合效应Thermo-hamper effect 热束缚效应Micro swirl 微涡流发动机性能专业术语英汉对照（4）Combustion chamber 燃烧室Divided combustion chamber 分开式燃烧室Semi-open combustion chamber 半开式燃烧室Open combustion chamber 开式燃烧室Direct injection combustion chamber 直喷式燃烧室Piston chamber 活塞顶内燃烧室M-process chamber 球型燃烧室Basin shaped combustion chamber 盆形燃烧室Swirl combustion chamber 涡流燃烧室Prechamber 预燃燃烧室Pre-swirl combustion chamber 涡流预燃室Heat-reserve combustion chamber 储能燃烧室Main combustion chamber 主燃室Subsidiary combustion chamber 副燃室L-combustion chamber L形燃烧室Wedge shaped combustion chamber 楔型燃烧室Bathtub shaped combustion chamber 盆形燃烧室Hemispherical combustion chamber 半球形燃烧室Volume ratio of combustion chamber 燃烧室体积比Calibre ratio of combustion chamber 燃烧室口径比Surface-volume ratio of combustion chamber 燃烧室面容比Area ratio of combustion chamber passage 燃烧室通道面积比Ignition 着火Ignition process 着火过程Ignition temperature 着火温度Compression ignition 压燃Spark ignition 点燃Cold flame 冷焰Blue flame 蓝焰Hot flame 热焰Pre-flame reaction 焰前反应Chain reaction 链反应Pre-mixing combustion 预混合燃烧Diffusion combustion 扩散燃烧Lean mixture combustion 稀薄燃烧Stratified combustion 层状燃烧Ignition delay period 滞燃期Rapid combustion period 速燃期Main combustion period 主燃期Normal combustion period 缓燃期After combustion period 后燃期Combustion duration 燃烧持续期Heat release beginning 放热始点Heat release end 放热终点Duration of heat release 放热持续期Combustion rate 燃烧率Heat release rate 放热率Heat release rate curve 放热规律Heat utilization ratio 热量利用率Spark advance angle 点火提前角Spark lag 点火延迟Pre-ignition 早燃Surface ignition 热面点火Miss-fire 失火Back fire 回火Flame propagation velocity 火焰传播速度Detonation 爆燃Squish area 挤气面积Quench effect 冷激效应Combustion swirl 燃烧涡流Squish swirl 挤压涡流Anti-squish swirl 反挤压涡流Maximum combustion pressure 最高燃烧压力Maximum combustion temperature 最高燃烧温度Pressure rise rate 压力升高率发动机性能专业术语英汉对照（5）Alternative fuel 代用燃料Emulsified fuel 乳化燃料Main fuel 主燃料Pilot-ignition fuel 引燃燃料Basic fuel 基础燃料Lower calorfic value of fuel 燃料低热值Cetane number 十六烷值Octane number 辛烷值Antiknock quality index 抗爆指数Antiknock sensitivity 抗爆敏感度Antiknock quality 抗爆性Polytropic index of expansion 膨胀多变指数Coefficient of molecular change 分子变更系数Initial exhaust 先期排气Free exhaust 自由排气Forced exhaust 强制排气Supercritical exhaust 超临界排气Subcritical exhaust 亚临界排气Exhaust advance angle 排气提前角Exhaust lag angle 排气迟后角Exhaust duration 排气持续期Exhaust pressure 排气压力Exhaust back pressure 排气背压Exhaust temperature 排气温度Residual gas 残余废气Coefficient of residual gas 残余废气系数Exhaust purification 排气净化Poisonous exhaust composition 排气有害万分Emission 排放物Concentration of emission 排放浓度Emission rate 排放分数Exhaust pollution 排气污染Exhaust smoke 排气烟度Soot 黑烟Exhaust particulate 排气微粒Exhaust gas recirculation 废气再循环Indicated work 指示功Indicated power 批示功率Mean indicated pressure 平均指示压力Indicated thermal efficiency 指示热效率Indicated specific fuel consumption 指示油耗率Indicated specific energy consumption 指示能耗率Indicator diagram 示功图Motoring indicator diagram 拖动示功图Low pressure indicator diagram 低压示功图Heat balance 热平衡Exhaust heat loss 排气热损失Cooling heat loss 冷却热损失Remainder heat loss 余项热损失Supercharging 增压Supercharging level 增压度Pressure ratio 增压比Boost pressure 增压压力Low pressure-charging 低增压Medium pressure-charging 中增压High pressure-charging 高增压Super high pressure-charging 超高增压Mechanical supercharging 机械增压Turbo-charging 废气涡轮增压Combined supercharging 复合增压Pulse turbo-charging 脉冲增压Constant-pressure turbo-charging 定压增压Inertia supercharging 惯性增压Intake fluctuation effect supercharging 气波增压器增压Two stage supercharging 两级增压发动机性能专业术语英汉对照（6）pulse converter supercharging 脉冲转换增压sequential turbocharging 相继涡轮增压tuned intake supercharging 谐波增压modular pulse converter supercharging 模件式脉冲转换增压inter-cooling 增压中冷inter-cooling level 中冷度exhaust expansion ratio through turbine 涡轮膨胀比equivalent area of turbine nozzle 涡轮当量喷嘴面积surge 喘振surge line 喘振线supercharger speed 增压器转速supercharger outlet temperature 增压器出口温度starting speed 起动转速declared speed 标称转速idling speed 最低空载转速maximum no-load speed 最高空载转速lowest continues speed with load 最低工作稳定转速economic speed 经济转速speed at maximum torque 最大转矩转速right-hand rotation 右转left-hand rotation 左转overspeed 超速coefficient of speed reserve 转速储备系数speed governing 调速coefficient of speed fluctuation 转速波动率maximum transient speed 最高瞬时转速minimum transient speed 最低瞬时转速speed recovery time 转速稳定时间transient speed regulation 瞬时调速率steady-state speed regulation 稳定调速率hunting 游车load 负荷full load 全负荷partial load 部分负荷overload 超负荷no-load 空载working condition 工况steady working condition 稳定工况variable working condition 变工况transient working condition 过渡工况declared working condition 标定工况economic working condition 经济工况mechanical loss 机械损失功率brake power 有效功率declared power 标称功率15-minute rated power 15 min功率one hour rated power 1h功率12-hour rated power 12h功率continues power 持续功率power per piston area 活塞面积功率power per cylinder 单缸功率power to bulk ratio 体积功率economic power 经济功率normal power 常用功率maximum power 最大功率gross power 总功率net power 净功率smoke limit power 冒烟极限功率derating power 减额功率power take-off 功率分支输出power reserve 储备功率adjusted power 修正功率standard power 标准功率coefficient of power reserve 功率储备系数mechanical power 机械功率汽车和半挂车车辆类型术语（英汉对照）机动车motor vehicle载货车truck微型货车mini truck轻型货车light truck中型货车medium truck重型货车heavy truck越野车off-road vehicle轻型越野车 light off-road vehicle中型越野车medium off-road vehicle重型越野车heavy off-road vehicle超重型越野车extra heavy off-road vehicle 自卸车dump truck/dumper轻型自卸车light dump truck中型自卸车medium dump truck重型自卸车heavy dump truck矿用自卸车mining dump truck牵引车towing vehicle半挂牵引车semi-trailer towing vehicle全挂牵引车full-trailer towing vehicle专用汽车special purpose vehicle厢式车van罐式车tanker起重举升车crane/lift truck专用自卸车special tipper仓栅式车/栅栏车箱式载货车stake truck 特种结构车special construction vehicle客车bus微型客车mini bus轻型客车light bus中型客车medium bus中型城市客车medium city bus中型长途客车medium intercity bus中型旅游客车 medium sight-seeing bus 中型团体客车medium private bus大型客车large bus大型城市客车large city bus大型长途客车large intercity bus大型旅游客车large sight-seeing bus 大型团体客车large private bus特大型客车extra bus铰接客车articulated bus双层客车double-deck bus轿车passenger car微型轿车mini car普通级轿车subcompact car中级轿车compact car中高级轿车intermediate car高级轿车limousine car半挂车semi-trailer轻型半挂车light semi-trailer中型半挂车medium semi-trailer重型半挂车heavy semi-trailer超重型半挂车extra heavy semi-trailer。

汽车发动机相关中英文对照

汽车发动机相关中英文对照发动机 engine燃机 intenal combusitonengine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine 往复式燃机 reciprocating internal combustion engine化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机 two-strokeengine四冲程发动机 four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooledengine油冷式发动机 oil-cooledengine水冷式发动机 water-cooled engine自然进气式发动机naturally aspirated engine煤气机 gas engine液化石油气发动机liquified petroleum gasengine柴油煤气机 diesel gas engine 多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine 双燃料发动机 duel fuel engine 热球式发动机 hot bulb engine 多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine 星型发动机 radial engine筒状活塞发动机trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquareengine长冲程发动机 undersquareengine等径程发动机 square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engineV形发动机 V-engine顶置气门发动机valve in-head engine侧置气门发动机 side valveengine无气门发动机 valveless engine多气门发动机 multi-valveengine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical engineW形发动机 w-engineI形发动机 I-engineL形发动机 L-engineF形发动机 F-engine二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volumecycle工作循环 working cycle等压循环 constant pressurecycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点 dead center上止点top dead center(upper deadcenter)下止点lower dead center(bottom deadcenter)上止点前budc(before upper deadcenter)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom deadcenter)下止点后abdc(after bottom deadcenter)缸径 cylinder bore缸径与行程 bore and stroke空气室 energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室 compression chamber排气量 displacement发动机排量 enginedisplacement活塞排量 piston swept volume气缸容量 cylinder capacity单室容量 single-chambercapacity容积法 volumetry压缩比 compression ratio临界压缩比critical compression ratio膨胀比 expansion ratio面容比 surface to volumeratio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力 brake meaneffective pressure(bmep)空燃比 air fuel ratio燃空比 fuel air ratio页脚燃料当量比 fuel equivalence ratio扭矩 torque单缸功率 power per cylinder 升功率 power per liter升扭矩 torque per liter升质量 mass per liter减额功率 derating power输出马力 shaft horsepower马力小时，马力时horsepower-hour总马力 gross horse power总功率 gross power净功率 net power燃油消耗量 fuel consumption 比燃料消耗率specific fuel consumption空气消耗率 air consumption 机油消耗量 oil consumption 有效马力 net horse power额定马力 rated horse power 马力重量系数horsepower-weight factor制动功率 brake horse power 制动热效率brake thermal efficiency总效率 overall efficiency排烟极限功率smoke limiting horsepower功率曲线 power curve机械损失 mechanical loss机械效率 mechanicalefficiency有效热效率effective thermal efficiency 充气系数 volumetricefficiency过量空气系数coefficient of excess air适应性系数 adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient 强化系数coefficient ofintensification校正系数 correction factor 换算系数 conversion factor 活塞平均速度 mean piston speed发动机转速engine speed (rotational frequency)怠速转速 idling speed 经济转速 economic speed起动转速 starting speed最低稳定工作转速 lowestcontinuous speed with load最大扭矩转速speed at maximum torque最高空转转速maximum no load governedspeed调速 speed governing超速 overspeed怠速 idling转速波动率 speed fluctuationrate工况working condition(operatingmode)额定工况declared working condition变工况 variable workingcondition稳定工况 steady workingcondition空载 no-load全负荷 full load超负荷 overload部分负荷 part load充量（进气） charge旋转方向 direction ofrotation顺时针 clockwise逆时针 counter-clockwise左转 left-hand rotation右转 right-hand rotation外径 major diameter中径 pitch diameter径 minor diameter径向间隙 radial clearance发动机性能 engine performance加载性能 loading performance起动性能 starting performance加速性能 accelerationperformance动力性能 power performance排放性能 emission performance空转特性 no loadcharacteristics负荷特性part throttle characteristics调速特性governor controlcharacteristics万有特性 mappingcharacteristics稳定调速率steady state speed governingrate气缸体和气缸盖cylinder block and head气缸体 cylinder block整体铸造cast inblock (cast enblock)发动机罩 engine bonnet气缸体加强筋engine block stiffening rib气缸 cylinder（转子机）缸体 stator缸径 cylinder bore气缸体机架 cylinder blockframe气缸盖 cylinder head配气机构箱valve mechanism casing气缸体隔片 cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片 cylinder headgasket气缸套cylinder liner(cylindersleeve)干式缸套 dry cylinder liner湿式缸套 wet cylinder liner气缸水套 water jacket膨胀塞 expansion plug防冻塞 freeze plug气缸壁 cylinder wall环脊 ring ridge排气口 exhaust port中间隔板 intermediate bottum导板 guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱 column燃烧室 combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室 prechamber涡流燃烧室`swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustionchamber浴盆形燃烧室 bathtub sectioncombustion chamber页脚L形燃烧室 L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室 closed spray chamber活塞顶燃烧室 piston chamber 爆发室 explosion chamber燃烧室容积比 volume ratio of combustion chamber燃烧室口径比 surface-volume ratio of combustion chamber 通道面积比 area ratio of combustion chamber passage曲轴箱通气口 crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖 crankcase door 曲轴箱防爆门crankcase explosion proofdoor主轴承盖 main bearing cap气缸盖罩 valve mechanismcover飞轮壳 flywheel cover扫气储器 scavenging air receiver活塞 piston裙部开槽活塞 split skirt pistonU形槽活塞 U-slot piston滚花修复活塞 knurled piston 圆顶活塞 dome head piston平顶活塞 flat head piston凸顶活塞 crown headpiston(convex head piston)凹顶活塞 concave head piston 阶梯顶活塞 step-head piston 筒形活塞 trunk piston椭圆形活塞 oval piston抗热变形活塞 autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞 invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞 slipper piston 活塞速度 piston speed活塞顶部 piston head活塞裙部 piston skirt整体活塞裙 solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙 slipper skirt隔热槽 heat dam活塞标记 piston mark活塞销 piston pin活塞销孔 piston pin boss活塞销衬套 piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环 piston ring组合式活塞环compound piston ring同心活塞环 concentric pistonring偏心活塞环 eccentric pistonring自由环 free ring闭合环 closed ring梯形环 keystone ring半梯形环 half keystone ring矩形环 rectangular ring油环 oil control ring开槽油环 slotted oil controlring螺旋弹簧加载双坡口油环 coilspring loaded slotted oilcontrol ring涨环 expander双坡口油环double bevelled oil controlring上坡口 internal bevel top下坡口 internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环 scrapper ring钩形环 napier ring镀铬活塞环chrome plated piston ring活塞衬环 piston ring expander活塞环槽 piston ring groove活塞环区 ring zone活塞环岸 piston ring land活塞环表面 back of ring曲柄连杆机构 connecting rod中心曲柄连杆机构central-located connectingrod偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆 connecting rod连杆小头 connecting rod smallend连杆大头 connnecting rod bigend连杆杆身 connecting rod shank副连杆 slave connecting rod叉形连杆fork-and-blade connecting rod主连杆 main connecting rod方形连杆 boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖 connecting rod cap连杆轴承 connecting rodbearing曲轴 crankshaft整体式曲轴 one-piececrankshaft组合式曲轴 assembledcrankshaft右侧曲轴 right-handcrankshaft左侧曲轴 left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端 crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度 shaft journaloverlap圆角 fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦 thin wall bearingshell曲轴油道 crankshaft oilpassage曲柄 crank曲柄臂 crank arm曲柄销 crank pin轴套 bush曲柄转角 crank angle曲柄半径 crank radius抛油圈 oil slander角度轮 degree wheel动平衡机 dynamic balancer平衡重 balancer weight扭振减振器torsional vibration damper页脚扭振平衡器 torsion balancer 谐振平衡器 harmonic balancer 振动平衡器 vibration balancer 曲轴链轮 crankshaft sprocket 转子轴颈 rotor journal偏心轴 eccentric shaft曲轴箱 crankcase闭式曲轴箱通风装置closed-crankcase ventilating system飞轮 flywheel飞轮齿圈 flywheel ring gear 飞轮芯棒 cantilever飞轮芯轴 flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记 flywheel mark当量系统 equivalent system当量轴长 equivalent shaft length一级往复惯性力reciprocating inertiaforce,1st order二级往复贯性力 reciprocating inertia force, 2nd order离心惯性力 centrifugalinertia force配气机构 valve gear凸轮轴 camshaft凸轮 cam整体式凸轮轴 one-piece camshaft组合式凸轮轴 assembled camshaft凸轮轴驱动机构 camshaft drive 赛车用凸轮轴 race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承 camshaft bearing 凸轮轴偏心轮 camshaft eccentric凸轮轴链轮 camshaft sprocket 凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮 camshaft gear wheel进口凸轮 inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam 凸轮轮廓 cam contour凸轮包角 cam angle凸轮升程 cam-lobe lift凸轮尖 cam nose凸轮从动件 cam follower齿轮传动机构gear drive 正时齿轮 timing gear链传动机构 chain drive链轮 sprocket wheel链轮盘 chain sprocket正时链条 timing chain带齿皮带 toothed timing belt链条紧轮 chain tension gear半速齿轮 half speed gear正时齿轮刻印记号timing gear punch mark气门 valve进气过程 intake process换气过程 gas exchange process扫气过程 scavenging process给气比 delivery ratio分层充气 stratified charge充量系数 volumetricefficiency涡流比 swirl rate进气涡流 intake swirl螺旋进气道进气 helical ductintake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流 intake trubulence进气提前角 intake advanceangle进气持续角 intake durationangle进气迟后角 intake lag angle进面值 time-area value气门升程 valve lift气门正时 valve timing扫气口面积 scavenging portarea菌形气门mashroom valve, poppet valve钠冷却气门 sodium filledvalve(natrium cooled valve)双气门 dual valve进气门 intake valve (suctionvalve,inlet valve)排气门 exhaust valve顶置气门 overhead valve侧置气门 side valve倾斜气门 inclined overheadvalve直立气门 vertical overheadvalve套筒式滑阀 sleeve valve气门机构 valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆 valve stem加大气门杆 oversize valvestem气门头 valve head气门工作面 valve face气门边限 valve margin气门弹簧座 valve-springretainer气门锁片 valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器 valve rotator气门室 valve cage气门油封 valve oil seal气门口 valve port气门座 valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seatring)气门座锥角 valve seat angle气门座宽度 valve seat width气门挺杆 valve tappet(valvelifter)液力挺杆 hydraulictappet(lifter)无间隙挺杆 zero-rush tappet(non-clearance tappet)筒形挺杆 barrel type tappet油压挺杆 ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位 tappet rotation排气门挺杆 exhaust valvelifter气门导管 valve guide气门杆导管 stem guide气门重叠度 stem overlap气门开启持续时间 valveduration气门正时标记 valve timingsign气门弹簧 valve spring气门弹簧 inner valve spring气门外弹簧 outer valve spring刚性缓冲弹簧 stiff bufferspring上紧弹簧 energizing spring防振气门弹簧 non-surgingspring弹簧座圈 spring retainer蝶形弹簧 belleville spring滚柱 roller气门室盖 valve chamber cover摇臂 rocker arm高升程摇臂 high lift rockerarm摇臂轴 rocker arm shaft推杆 push-rod页脚摇臂支架 rocker arm bracket 气门摇臂室罩valve rocker chamber cover导向轮 guide wheel导杆 slide bar导轨 slide rail紧轮 tensioning wheel链条紧调节装置assembly chain tension adjuster紧带轮 tensioning pulley传动带紧装置 belt tensioner 同步驱动皮带 synchronous belt 同步驱动皮轮synchronous belt pulley供油系 fuel system控制燃烧系统controlled combustion system 反湿气装置 antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管 constant purgeline碳罐净化管 canister purgeline供油量 fuel delivery循环供油量 fuel delivery per cycle额定供油量 rated fueldelivery怠速供油量idling speed fuel delivery供油规律 fuel supply rate curve油量调节装置 fuel controlunit供油提前角fuel supply advance angle进油计量 inlet metering几何供油行程geometric fuel deliverystroke供油率 fuel supply rate燃油通道 fuel gallery有效行程 effective stroke剩余行程 remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载 variable volume unloading收缩容积 retraction volume燃油喷油装置fuel injection equipment燃油喷射泵 fuel injectionpump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵 in-line fuelinjection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuelinjection pump上部安装燃油喷射泵 highflanged-mounted fuelinjection pump侧向安装燃油喷射泵side-mounted fuel injectionpump端部突缘安装式燃油喷射泵end flange-mounted fuelinjection pumpV形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injectionpump蓄能式燃油喷射泵accumulator fuel injectionpump往复式燃油喷射泵reciprocating fuel injectionpump驱动轴式燃油喷射泵driveshaft fuel injectionpump单缸式燃油喷射泵single cylinder fuelinjection pump圆柱式燃油喷射泵cylindrical fuel injectionpump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injectionpump多缸燃油喷射泵multicylinder fuel injectionpump框架安装式燃油喷射泵cradle mounted injection pump喷油始点 fuel injectionbeginning喷油终点 fuel injection end喷油持续角fuel injection duration angle喷油延迟 injection delay引燃喷射 pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目 number ofcylinders of an injectionpump无气喷射 solid injection喷射正时 injection timing集中喷射 group injection喷油器 injector整体式喷油器 unit injector喷嘴 nozzle轴针式喷嘴 pintle type nozzle环槽式喷嘴 annular slotnozzle孔式喷嘴 hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴 orifice platenozzle开式喷嘴 open nozzle闭式喷嘴 closed nozzle喷油提前器 timing advanceunit喷射泵壳体 injection pumphousing针阀 needle芯轴 central spindle喷嘴壳体 nozzle body针阀升程 needle lift喷嘴盖形螺母 nozzle cap nut喷油器壳体 nozzle holder突缘安装喷油器壳体 flanged-mounted injection nozzleholder燃油喷射泵传动装置transmision of an injectionpump喷嘴锥体 nozzle hole cone柱塞 plunger柱塞套 barrel柱塞行程 plunger stroke喷孔 spray orifice海拔控制器 altitude control提前器飞锤 flyweight喷孔长径比 ratio of nozzlehole length nozzle diameter页脚喷嘴液动力特性nozzle hydrokinetic characteristics动态相位 dynamic phase喷孔面积 nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压 injection back pressure高压油管 high pressure pipe 平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程 prestroke收缩行程 retraction stroke燃油箱 fuel tank油箱盖 fuel tank油位表 fuel level gauge注油控制装置 fill control system汽油箱 gasoline tank( petrol tank)汽油供给管 gasoline feed pipe 加油管 filler tube放油螺塞 drain plug吸油管 suction pipe刚性燃油管 rigid fuel pipe进油孔 fuel feed hole供油管 supply pipe通气管 bleeding pipe通气管 bleeding pipe泄油阀 spill valve泄油孔口 spill port进油阀 inlet valve最大油量限制器maximum fuel stop滴油 dribble燃油表 fuel gauge输油泵 feed pump燃油泵 fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump 齿轮式输油泵gear fuel supply pump电动燃油泵 eletric fuel pump 带真空泵的汽油泵vacuum pump with fuel pump起动加油器 primer起动给油杆 primer lever燃油泵上体 fuel pump body燃油泵下体 fuel pump base燃油泵盖 bowl cover进油口接头fuel inlet neck出油口接头 fuel dischargeport输出阀 delivery valve泵油元件 pump element回油阀部件fuel return valve assembly化油器 carburetor化油器系统 carburetor circuit简单化油器 elementarycarburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器 four-barrelcarburetor上吸式化油器 updaughtcarburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensatingcarburetor化油器附加器 adaptorcarburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头 carburetor adaptor阻风门 choke valve阻风活塞 choke piston阻风板 choke plate自动阻风门 automatic choke阻风门拉钮 choke button电控自动阻风门electric-assisted choke阻风管 choke tube喉管 venturi双重或三重喉管double & triple venturi阻风门拉线 choke cable化油器小喉管 booster venturi浮子系 float system浮子 float环形浮子 annular float同心式浮子 concentric float浮子支销 float hinge pin浮子针阀 float needle valve阀针 valve needle浮子油面 float level浮子臂 float arm侧置浮子室式 side float type怠速阀 idle valve怠速针阀 idle needle省油器 economizer省油器阀 economizer valve辅助空气阀 auxiliary air-valve加速油井 accelerating well加速泵 accelerating pump加速泵喷嘴accelerating pump nozzle油门 throttle手油门 hand throttle节气门操纵手柄throttle control lever真空加浓器 vacuum booster加浓器 excess fuel device量孔体 jet block怠速量孔 idle metering jet主量孔 main metering jet剂量阀活塞 dosage valvepiston空气量孔 air jet燃油滤清器 fuel filter沉淀杯 sediment bowl串联过滤器 in-line filter燃油箱装过滤器 in-tank filter调速器 governor飞球式调速器 flyball governor调速器 governor飞球式调速器 flyball governor液压调速器 hydraulic governor真空转速调速器vacuum speed governor惯性调速器 inertia governor离心调速器 centrifugalgovernor调速器重锤 governor weight空气滤清器及进排气系统air cleaner and intake andexhaust sytem空气滤清器 air filter冲压式空气滤清器 ram airclearner页脚恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器 paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯 filter element空气滤清器壳体 air filter housing空气滤清器盖 air filter cover 滤清器密封圈 filter seal ring 滤网 sieve滤纸盘或膜filter paper disc or membrane 进气和排气系统intake and exhaust system排气管 exhaust pipe排气抽气管 exhaust extraction duct扫气泵 scavenging pump进气预热装置 intake preheater 进气歧管 intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管 cold manifold冲压式进气歧管ram intake manifold排气歧管 exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve超高度歧管 high-rise manifold 升温横跨管道 heat crossover 排气横跨管道 exhaustcrossover预热点 hot spot阻风门加热器 choke heater热空气导流管 hot air duct隔热板 heat shield排气再循环阀exhaust -gas-recirculation消声器 silencer进气消声器 intake silencer排气消声器 exhaust silencer 金属垫片式消声器steel pack muffler玻璃丝消声器 glass pack muffler空洞消声器 gutted muffler 前排气管 front exhaust pipe尾管 tail pipe消声器联接管 intermediatepipe热空气管 hot air pipe曲轴箱通风管 crankcase bleedpipe隔声罩 acoustic hood进气消声器元件 silencerelement真空泵 vacuum pump指示功率 indicated power指示热效率indicated thermal efficiency指示油耗率 indicated specificenergy consumption示功图 indicator diagram冷却系 cooling system风冷 air cooling水冷 water-cooling循环流冷却系cooling recovery system自然循环液冷却系统 naturalcirculation type coolingsystem热流循环液冷却系统thermo-siphon circulationtype cooling system温差循环液冷却系统 gravitycirculation water coolingsystem压力式水冷却系统 positivecirculation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation coolingsystem强制循环式化冷系统 forced-feed water circulation system封闭式液冷系统sealed cooling system散热器 radiator片式散热器 finned radiator管式散热器 tubular radiator蜂窝式散热器 cellularradiator哈里逊式散热器Harrison type radiator带板式散热器 ribbon typeradiator上水箱 upper tank下水箱 lower tank涨溢箱 expansion tank散热器芯 radiator core之字形管散热器芯 film core管-片式散热器芯 fin and tubecore散热器加水口盖 radiatorfilter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩 radiator cowl散热器百叶窗 radiator shutter散热器保温帘 radiator rollerblind散热片 cooling fin缸盖散热片 cylinder head fin缸体散热片 cylinder block fin控温装置temperature regulating device恒温器 thermostat恒温器主阀 thermostat mainvalve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵 water pump水泵体 pump casing水泵叶轮 water pump impeller旁通进水口water by-pass inlet neck循环泵 circulating pump主进水口 water main inletport出水口 water outlet port自调式水封 self-adjustingseal unit溢流管 overflow pipe导流板 deflector风扇 fan(blower)轴流式风扇 axial flow fan离心式风扇 centrifugal fan风扇壳体 blower casing风扇导流罩 fan cowl风扇毂 fan hub风扇叶片 fan blade风扇叶轮 blower impeller风扇导流定子 blower stator风扇皮带轮 fan pulley三角皮带 v-belt风扇护罩 fan shroud风扇叶轮叶片 impeller vane冷却用空气 cooling air风扇导流叶片 stator vane强制风冷 forced-air cooling自然风冷 natural air cooling页脚风道 air ducting润滑系 lubrication system润滑 lubrication气缸上部润滑upper cylinder lubrication压力润滑 pressure-feed lubrication压力润滑法 forced lubrication 自动润滑 automaticlubrication飞溅润滑 splash lubrication 润滑周期 lubrication interval 边界润滑 borderlinelubrication曲轴箱机油油盘 crankcase oil pan油底壳 oil pan机油盘放油塞 sump plug集油器 oil collector机油泵 oil pump计量式机油泵 metering oil pump齿轮式机油泵 gear type oil pump转子式机油泵 rotor-type oil pump机油泵出油管 oil pump outlet pipe放油口 oil drain hole油道 oil duct断油开关 cut-off cock机油散热器 oil cooler机油滤清器 oil filter机油粗滤器 primary oil filter 机油精滤器 secondary oilfilter全流式机油滤清器full-flow oil filter分流式机油滤清器 by-pass oil filter离心式机油滤清器centrifugal oil filter整体式滤芯integral filtering element细滤器滤芯 filter element滤清器壳 filter box滤片filtering disc机油减压器 oil pressurerelief valve旁通阀 by-pass oil filter机油滤网 oil strainer加机油孔 oil filter cap滤芯轴 filter shaft刮片组件 cleaning edge机油量尺 dipstick机油滤网 oil strainer增压器 supercharger 增压和扫气装置 pressure-charging and scavenging unit增压装置 supercharging device涡轮增压器 turbo-charger气波增压器 comprex pressurewave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass增压器叶轮 superchargerimpeller惯性增压 inertiasupercharging机械增压mechanical supercharging涡轮增压 turbo-charging增压比 supercharge ratio增压压力 boost pressure增压中冷 inter-cooling中冷度 inter-cooling level增压度 supercharging level喘振 surge喘振线 surge line轴流式涡轮 axial-flow turbine脉冲进气 ram charging发动机试验 engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmosphericconditions大气压力 atmospheric pressure进气温度 inlet airtemperature进气温度 inlet airtemperature功率校正 power correction功率标定 power rating功率换算 power conversion校正系数 correction factor换算系数 performance test性能试验 performance test起动性能试验 starting abilitytest怠速试验 idle running test道路负荷试验 road load test各缸工作均匀性试验cylinder variation test背压试验 back pressure test最低稳定工作转速试验 lowestcontinuous speed test withload背部泄漏试验 back-leakagetest调整试验 adjustment test热平衡试验 heat balance test快速磨损试验accelerated wear test热冲击试验 thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验 cylinder fuel-cuttest增压机匹配试验turbo-charger matching test排气分析试验 exhaust analysistest突变负荷试验sudden load change test稳定性试验 stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验 verification test鉴定试验 approval test可靠性试验 reliability test耐久性试验 durability test定型试验 type approval test验收试验 acceptance test现场试验 field test出厂试验 delivery test抽查试验 spot check test复查试验 re-check test台架试验 bench test强化试验 hop-up test发动机试验台 engine test bed底盘测功机 chassisdynamometer测功机 dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机 electricdynamometer扭矩仪 torque meter转速表 tachometer温度测量 thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪 hot wireanemometer电子示功仪 electronicindicator燃烧分析仪 combustionanalyzer页脚压力传感器 pressuretransducer精密声级计precision sound level meter 排放 emission排放物 emission排气污染物 gaseous pollutant 蒸发排放物 evaporative emission曲轴箱排放物 crankcase emission漏气 blowby gas氨氧化物 oxids of nitrogen一气化碳 carbon monoxide碳氢化合物 hydrocarbon甲烷 methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons微粒物 particulated matter黑烟 black smoke蓝烟 blue smoke白烟 white smoke碳烟 soot光化学烟雾smog臭味 odor丙烷 propane排放浓度 concentration of emission排气烟度 exhaust smoke先期排气 initial exhaust亚临界排气 subcritical exhaust超临界排气 supercritical exhaust强制排气 forced exhaust自由排气 free exhaust排气提前角 exhaust advance angle排气迟后角 exhaust lag angle 排气热损失 exhaust heat loss 排气净化 exhaust purification 排气背压 exhaust backpressure残余废气 residual gas排气有害成分poisonous exhaust composition 柴油机排烟 diesel smoke综合排放浓度 composite concentration of exhaust emission综合排放质量 composite massof exhaust emission排放系数 emission factor排放率emission index 质量排放量 mass emission比排放量 brake specificemission排放物控制系统emission control system排气排放物控制系统exhaust emission controlsystem二次空气 secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve二次空气转流阀secondary air diverter valve二次空气喷射装置secondary air injectionsystem二次空气喷射管secondary air injection tube二次空气喷射减速压阀secondary air injectionrelief valve脉动空气装置 pulsating airsystem二次空气泵 secondary air pump曲轴箱排放物控制系统crankcase emission controlsystem曲轴箱双通风系统crankcase closed system曲轴箱单通风系统crankcase sealed system曲轴箱强制通风装置positive crankcaseventilationPCV阀 PCV valve蒸发排放物控制系统evaporative emission controlsystem活性碳罐贮存装置charcoal canister storagesystem活性碳罐 charcoal canister曲轴箱贮存装置crankcase storage system空气滤清器贮存装置air filter storage system燃油箱止回阀 fuel tank checkvalve油气分离器fuel and vapor separator清除阀 furge valve催化转化系统catalytic converting system催化燃烧分析仪catalytic combustion analyzer催化剂 catalyst转化器 converter催化转化器 catalyticconverter轴流式转化器AXIAL FLOW TYPE CONVERTER径流式转化器RADIAL FLOW TYPE CONVERTER下流式转化器down flow type converter上流式转化器up flow type converter双床式转化器 dual bedconverter单床式转化器 single bedconverter氧化型催化剂 oxidationcatalyst还原型催化剂 reductioncatalyst三元催化剂 three-way catalyst贵金属催化剂 noble metalcatalyst普通金属催化剂base metal catalyst稀土催化剂 rare earthcatalyst催化剂耗损 catalyst attrition催化剂收缩 catalyst shrinkage催化剂中毒 catalyst poisoning比表面积 specific surfacearea空速 space velocity载体涂料 washcoat双重催化系统 dual -catalystsystem催化箱 catalyst container载体 substrate整体式载体 monolithicsubstrate颗粒式载体 pelleted substrate转化效率 conversionefficiency熄灯温度 light-offtemperature热态反应系统thermal reacting system热反应器 thermal reactor反应式歧管 reactive manifold过热保护装置over heating protectionsystem过热警报装置over heating warning system排气口衬套 exhaust port liner页脚。

发动机专业英语词汇.

发动机engine内燃机internal combustion engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前BTDC(before top dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力每小时，马力/时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumptioneffective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacketpower performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion chamber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve)双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump 无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice燃油滤清器fuel filter增压器supercharger增压装置supercharging device涡轮增压器turbo-charger机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging levelelectronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission 空燃比反馈控制系统air-fuel ratio feedback control system理论配比stoichiometric高效带window氧传感器oxygen sensor稀混合气lean mixture浓混合气rich mixture分层充气stratified charge温度补偿temperature compensating温度传感器temperature sensor压力传感器pressure sensor位置传感器position sensor转速传感器speed sensor机械磨损mechanical wear化学磨损chemical wear热磨损thermic wear疲劳磨损fatigue wear腐蚀性磨损corrosion wear故障磨损failure wear故障malfunctioning断裂breakdown损坏damage更换（零件）replacing擦伤scratching刮伤scoring摩托车motorcycle轻便摩托车moped轿车passenger car微型轿车minicar普通级轿车subcompact car中级轿车compact car中高级轿车intermediate car高级轿车limousine (pullman saloon)活顶轿车convertible saloon旅行轿车station wagon短头轿车forward control passenger car 小型轿车coupe敞蓬小轿车drop head coupe跑车sports car赛车racer (racing car)单座小客车one-seater七座小客车seven-seater越野车off-road vehicle轻型越野车light-off-road vehicle中型越野车medium off-road vehicle重型越野车heavy off -road vehicle超重型越野车extra heavy off- road vehicle 吉普车jeep硬顶吉普车hard top jeep客车bus微型客车minibus轻型客车light bus中型客车medium bus大型客车large bus客货两用小客车estate car (estate)多用途客车multipurpose vehicle厢式小客车closed car出租小客车taxicar城市客车urban bus大客车coach城间大客车intercity bus长途大客车long distance coach旅游客车sightseeing bus(touring bus)铰接客车articulated bus无轨客车trolley bus双层客车double-deck bus团体客车private coach货车truck(lorry)微型货车mini-truck轻型货车light truck中型货车medium truck重型货车heavy truck公路货车highway vehicle小型货车pick-up平板货车platform truck(flat bed truck)通用货车general -purpose vehicle短轴距货车short-wheel base truck长轴距货车long-wheelbase truck集装箱运输货车container carrier客货两用车cargo-bus厢式货车van牵引汽车towing vehicle全挂牵引汽车towing vehicle牵杆式牵引车full-trailer towing vehicle半挂牵引车semi-trailer towing vehicle道路列车road train客用道路列车passenger road train铰接式道路列车articulated road train双挂式道路列车double road train混合式道路列车composite road train天然气车辆natural gas vehicle(NGV)压缩天然气车辆compressed natural gas vehicle 液化天然气车辆liquid petroleum gas vehicle液化石油气车辆liquid petroleum gas vehicle双燃料车辆duel fuel vehicle单燃料车辆single fuel vehicle专用车special vehicle垃圾车dust car (refuse collector)冷藏车refrigerated van洒水车street sprinkler (street flusher)囚车prison van殡仪车hearse售货车mobile store(mobile shop)图书馆车mobile library宣传车mobile louderspeaker商业广告车spiel truck展览汽车demonstration car博览会专用车fairground vehicle流动艺术展览车artmobile邮政车mobile post office运油车fuel tanker加油车refueller飞机牵引车aircraft tractor救护车ambulance (medical vehicle)病院汽车clinic car医疗急救车rescue ambulanceX射线诊断车mobile-x-ray clinic防疫监测车mobile epidemic control vehicle计划生育车mobile family -planning clinic伤残者运送车handicapped person carrier炊事车kitchen vehicle餐车mobile canteen沐浴车mobile shower bath保温车insulated van电视转播车TV relaying vehicle电视录像车video recording vehicle摄影车mobile photographic studio电影放映车film projection vehicle邮件运输车mail carrier农用车farm vehicle种子检测车plant seeds inspection van植物保护车plant pest control vehicle计量检测车metrology inspection vehicle环境检测车mobile environment monitor畜禽防疫车mobile animal eqidemic control交通监理车traffic control car刑事勘察车mobile crime investigation vehicle气卸散装水泥车bulk-cement pneumatic delivery tanker气卸散装煤粉车bulk-coal powder pneumatic delivery tanker气卸散装电石粉车bulk-calcium carbide pneumatic delivery tanker 气卸散装化学粉粒车bulk-chemicals pneumatic delivery tanker食用植物油运油汽车edible oil tanker食用植物油加油车edible oil pump delivery tanker活鱼运输车life fish carrier气卸散装面粉车bulk-flour pneumatic delivery tanker吸尘车vacuum sweeper高压清洗车high-pressure sewer flushing vehiclechart of automotive model后驱动汽车rear drive automobile前驱动汽车前轮距track front后轮距track rear双胎间距space between twin wheels前悬front overhang后悬rear overhang离地间隙ground clearance纵向通过角ramp angle接近角approach angle离出角departure angle车架高度height of chassis above ground驾驶室后车架最大可用长度maximum usable length of chassis behind cab 车身长度货厢容积loading surface门高door height门宽door width车架有效长度chassis frame useful length比功率power/mass ratio比扭矩torque/maximum total mass ratio。

发动机中英文术语 ( Carrot Download) 2007-3-14发动机 engine内燃机 intenal combusiton engine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发动机 compression ignition engine往复式内燃机 reciprocating internal combustion engine 化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机 water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 multiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead camshaft engine V形发动机 V-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical engineW形发动机 w-engineI形发动机 I-engineL形发动机 L-engineF形发动机 F-engine二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程 expansion-exchange stroke换气压缩行程 exchange-compression stroke止点 dead center上止点 top dead center(upper dead center)下止点 lower dead center(bottom dead center)上止点前 budc(before upper dead center)上止点后 atdc(after top dead cetner)下止点前 bbdc(before bottom dead center)下止点后 abdc(after bottom dead center)缸径 cylinder bore缸径与行程 bore and stroke空气室 energy chamber气缸余隙容积 cylinder clearance volume燃烧室容积 combustion chamber volume气缸最大容积 maximum cylinder volume压缩室 compression chamber排气量 displacement发动机排量 engine displacement活塞排量 piston swept volume气缸容量 cylinder capacity单室容量 single-chamber capacity容积法 volumetry压缩比 compression ratio临界压缩比 critical compression ratio膨胀比 expansion ratio面容比 surface to volume ratio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio燃空比 fuel air ratio燃料当量比 fuel equivalence ratio扭矩 torque单缸功率 power per cylinder升功率 power per liter升扭矩 torque per liter升质量 mass per liter减额功率 derating power输出马力 shaft horsepower马力小时，马力时 horsepower-hour总马力 gross horse power总功率 gross power净功率 net power燃油消耗量 fuel consumption比燃料消耗率 specific fuel consumption空气消耗率 air consumption机油消耗量 oil consumption有效马力 net horse power额定马力 rated horse power马力重量系数 horsepower-weight factor制动功率 brake horse power制动热效率 brake thermal efficiency总效率 overall efficiency排烟极限功率 smoke limiting horsepower功率曲线 power curve机械损失 mechanical loss机械效率 mechanical efficiency有效热效率 effective thermal efficiency充气系数 volumetric efficiency过量空气系数 coefficient of excess air适应性系数 adaptive coefficient扭矩适应性系数 coefficient of torque adaptibility 转速适应性系数 speed adaptive coefficient强化系数 coefficient of intensification校正系数 correction factor换算系数 conversion factor活塞平均速度 mean piston speed发动机转速 engine speed (rotational frequency)怠速转速 idling speed经济转速 economic speed起动转速 starting speed最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque最高空转转速 maximum no load governed speed调速 speed governing超速 overspeed怠速 idling转速波动率 speed fluctuation rate工况 working condition(operating mode)额定工况 declared working condition变工况 variable working condition稳定工况 steady working condition空载 no-load全负荷 full load超负荷 overload部分负荷 part load充量（进气） charge旋转方向 direction of rotation顺时针 clockwise逆时针 counter-clockwise左转 left-hand rotation右转 right-hand rotation外径 major diameter中径 pitch diameter内径 minor diameter径向间隙 radial clearance发动机性能 engine performance加载性能 loading performance起动性能 starting performance加速性能 acceleration performance动力性能 power performance排放性能 emission performance空转特性 no load characteristics负荷特性 part throttle characteristics调速特性 governor control characteristics 万有特性 mapping characteristics稳定调速率 steady state speed governing rate 气缸体和气缸盖 cylinder block and head气缸体 cylinder block整体铸造 cast inblock (cast enblock)发动机罩 engine bonnet气缸体加强筋 engine block stiffening rib气缸 cylinder（转子机）缸体 stator缸径 cylinder bore气缸体机架 cylinder block frame气缸盖 cylinder head配气机构箱 valve mechanism casing气缸体隔片 cylinder spacer气缸盖密封环 cylinder head ring gasket气缸盖垫片 cylinder head gasket气缸套 cylinder liner(cylinder sleeve)干式缸套 dry cylinder liner湿式缸套 wet cylinder liner气缸水套 water jacket膨胀塞 expansion plug防冻塞 freeze plug气缸壁 cylinder wall环脊 ring ridge排气口 exhaust port中间隔板 intermediate bottum导板 guideway创成半径（转子机） generating radius缸体宽度（转子机） operating width机柱 column燃烧室 combustion chamber主燃烧室 main combustion chamber副燃烧室 subsidiary combustion chamber预燃室 prechamber涡流燃烧室` swirl combustion chamber分开式燃烧室 divided combustion chamber涡流式燃烧室 turbulence combustion chamber半球形燃烧室 hemispherical combustion chamber浴盆形燃烧室 bathtub section combustion chamberL形燃烧室 L-combustion chamber楔形燃烧室 wedge-section combustion chamber开式燃烧室 open combustion chamber封闭喷射室 closed spray chamber活塞顶内燃烧室 piston chamber爆发室 explosion chamber燃烧室容积比 volume ratio of combustion cahmber燃烧室口径比 surface-volume ratio of combustion chamber 通道面积比 area ratio of combustion chamber passage曲轴箱通气口 crankcase breather凸轮轴轴承座 camshaft bearing bush seat定时齿轮室罩 camshaft drive(gear)cover曲轴箱检查孔盖 crankcase door曲轴箱防爆门 crankcase explosion proof door主轴承盖 main bearing cap气缸盖罩 valve mechanism cover飞轮壳 flywheel cover扫气储器 scavenging air receiver活塞 piston裙部开槽活塞 split skirt pistonU形槽活塞 U-slot piston滚花修复活塞 knurled piston圆顶活塞 dome head piston平顶活塞 flat head piston凸顶活塞 crown head piston(convex head piston)凹顶活塞 concave head piston阶梯顶活塞 step-head piston筒形活塞 trunk piston椭圆形活塞 oval piston抗热变形活塞 autothermic piston不变间隙活塞 constant clearance piston镶因瓦钢片活塞 invar strut piston直接冷却式活塞 direct-cooled piston间接冷却式活塞 indirect cooled piston滑裙活塞 slipper piston活塞速度 piston speed活塞顶部 piston head活塞裙部 piston skirt整体活塞裙 solid skirt活塞裙扩大衬簧 piston skirt expander滑履式活塞裙 slipper skirt隔热槽 heat dam活塞标记 piston mark活塞销 piston pin活塞销孔 piston pin boss活塞销衬套 piston pin bushing全浮式活塞销 full-floating piston pin半浮式活塞销 semifloating piston pin固定螺钉式活塞销 set screw piston pin活塞环 piston ring组合式活塞环 compound piston ring同心活塞环 concentric piston ring偏心活塞环 eccentric piston ring自由环 free ring闭合环 closed ring梯形环 keystone ring半梯形环 half keystone ring矩形环 rectangular ring油环 oil control ring开槽油环 slotted oil control ring螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander双坡口油环 double bevelled oil control ring内上坡口 internal bevel top内下坡口 internal bevel bottom边缘坡口油环 bevelled-ege oil control ring刮油环 scrapper ring钩形环 napier ring镀铬活塞环 chrome plated piston ring活塞衬环 piston ring expander活塞环槽 piston ring groove活塞环区 ring zone活塞环岸 piston ring land活塞环内表面 back of ring曲柄连杆机构 connecting rod中心曲柄连杆机构 central-located connecting rod偏心曲柄连杆机构 offset connecting rod铰接曲柄边杆机构 hinged connecting rod连杆 connecting rod连杆小头 connecting rod small end连杆大头 connnecting rod big end连杆杆身 connecting rod shank副连杆 slave connecting rod叉形连杆 fork-and-blade connecting rod 主连杆 main connecting rod方形连杆 boxed rod绞链式连杆 hinged type connecting rod 活节式连杆 articulated connecting rod 连杆盖 connecting rod cap连杆轴承 connecting rod bearing曲轴 crankshaft整体式曲轴 one-piece crankshaft组合式曲轴 assembled crankshaft右侧曲轴 right-hand crankshaft左侧曲轴 left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端 crankshaft front end曲轴主轴颈 crankshaft main journal轴颈重叠度 shaft journal overlap圆角 fillet主轴承main bearing曲轴止推轴承 crankshaft thrust bearing 薄臂轴瓦 thin wall bearing shell曲轴油道 crankshaft oil passage曲柄 crank曲柄臂 crank arm曲柄销 crank pin轴套 bush曲柄转角 crank angle曲柄半径 crank radius抛油圈 oil slander角度轮 degree wheel动平衡机 dynamic balancer平衡重 balancer weight扭振减振器 torshional vibration damper 扭振平衡器 torsion balancer谐振平衡器 harmonic balancer振动平衡器 vibration balancer曲轴链轮 crankshaft sprocket转子轴颈 rotor journal偏心轴 eccentric shaft曲轴箱 crankcase闭式曲轴箱通风装置 closed-crankcase ventilating system 飞轮 flywheel飞轮齿圈 flywheel ring gear飞轮芯棒 cantilever飞轮芯轴 flywheel spindle飞轮的惯量矩 flywheel moment of inertia飞轮标记 flywheel mark当量系统 equivalent system当量轴长 equivalent shaft length一级往复惯性力 reciprocating inertia force,1st order 二级往复贯性力 reciprocating inertia force, 2nd order 离心惯性力 centrifugal inertia force配气机构 valve gear凸轮轴 camshaft凸轮 cam整体式凸轮轴 one-piece camshaft组合式凸轮轴 assembled camshaft凸轮轴驱动机构 camshaft drive赛车用凸轮轴 race camshaft凸轮轴轴颈 camshaft bearing journal凸轮轴轴承 camshaft bearing凸轮轴偏心轮 camshaft eccentric凸轮轴链轮 camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮 camshaft gear wheel进口凸轮 inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓 cam contour凸轮包角 cam angle凸轮升程 cam-lobe lift凸轮尖 cam nose凸轮从动件 cam follower齿轮传动机构gear drive正时齿轮 timing gear链传动机构 chain drive链轮 sprocket wheel链轮盘 chain sprocket正时链条 timing chain带齿皮带 toothed timing belt链条张紧轮 chain tension gear半速齿轮 half speed gear正时齿轮刻印记号 timing gear punch mark气门 valve进气过程 intake process换气过程 gas exchange process扫气过程 scavenging process给气比 delivery ratio分层充气 stratified charge充量系数 volumetric efficiency涡流比 swirl rate进气涡流 intake swirl螺旋进气道进气 helical duct intake导流屏式气门进气 masked valve intake切向进气道进气 tangential duct intake进气紊流 intake trubulence进气提前角 intake advance angle进气持续角 intake duration angle进气迟后角 intake lag angle进面值 time-area value气门升程 valve lift气门正时 valve timing扫气口面积 scavenging port area菌形气门 mashroom valve, poppet valve钠冷却气门 sodium filled valve(natrium cooled valve) 双气门 dual valve进气门 intake valve (suction valve,inlet valve)排气门 exhaust valve顶置气门 overhead valve侧置气门 side valve倾斜气门 inclined overhead valve直立气门 vertical overhead valve套筒式滑阀 sleeve valve气门机构 valve gear直接式气门驱动机构 direct valve gear间接式气门驱动机构 indirect valve gear气门杆 valve stem加大气门杆 oversize valve stem气门头 valve head气门工作面 valve face气门边限 valve margin气门弹簧座 valve-spring retainer气门锁片 valve key气门间隙调节螺钉 valve lash adjusting screw气门旋转器 valve rotator气门室 valve cage气门油封 valve oil seal气门口 valve port气门座 valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角 valve seat angle气门座宽度 valve seat width气门挺杆 valve tappet(valve lifter)液力挺杆 hydraulic tappet(lifter)无间隙挺杆 zero-rush tappet (non-clearance tappet)筒形挺杆 barrel type tappet油压挺杆 ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位 tappet rotation排气门挺杆 exhaust valve lifter气门导管 valve guide气门杆导管 stem guide气门重叠度 stem overlap气门开启持续时间 valve duration气门正时标记 valve timing sign气门弹簧 valve spring气门内弹簧 inner valve spring气门外弹簧 outer valve spring刚性缓冲弹簧 stiff buffer spring上紧弹簧 energizing spring防振气门弹簧 non-surging spring弹簧座圈 spring retainer蝶形弹簧 belleville spring滚柱 roller气门室盖 valve chamber cover摇臂 rocker arm高升程摇臂 high lift rocker arm摇臂轴 rocker arm shaft推杆 push-rod摇臂支架 rocker arm bracket气门摇臂室罩 valve rocker chamber cover导向轮 guide wheel导杆 slide bar导轨 slide rail张紧轮 tensioning wheel链条张紧调节装置 assembly chain tension adjuster张紧带轮 tensioning pulley传动带张紧装置 belt tensioner同步驱动皮带 synchronous belt同步驱动皮轮 synchronous belt pulley供油系 fuel system控制燃烧系统 controlled combustion system反湿气装置 antipercolator电子燃油喷射 electronic fuel injection蒸气回收装置 vapor recovery system燃油蒸气回收系统 fuel vapor recovery system液体回收装置 liquid withdrawal system恒量净化管 constant purge line碳罐净化管 canister purge line供油量 fuel delivery循环供油量 fuel delivery per cycle额定供油量 rated fuel delivery怠速供油量 idling speed fuel delivery供油规律 fuel supply rate curve油量调节装置 fuel control unit供油提前角 fuel supply advance angle进油计量 inlet metering几何供油行程 geometric fuel delivery stroke供油率 fuel supply rate燃油通道 fuel gallery有效行程 effective stroke剩余行程 remainder stroke变行程计量 variable stroke metering等容卸载 constant volume unloading变容卸载 variable volume unloading收缩容积 retraction volume燃油喷油装置 fuel injection equipment燃油喷射泵 fuel injection pump滚轮式燃油喷射泵 roll fuel injection pump凸轮轴式燃油喷射泵 camshaft fuel injection pump直列式燃油喷射泵 in-line fuel injection pump伺服式燃油喷射泵 servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵 high flanged-mounted fuel injection pump侧向安装燃油喷射泵 side-mounted fuel injection pump端部突缘安装式燃油喷射泵 end flange-mounted fuel injection pump V形燃油喷射泵 vee fuel injection pump脉动式燃油喷射泵 jerk fuel injection pump螺纹安装燃油喷射泵 screw-mounted fuel injection pump蓄能式燃油喷射泵 accumulator fuel injection pump往复式燃油喷射泵 reciprocating fuel injection pump驱动轴式燃油喷射泵 driveshaft fuel injection pump单缸式燃油喷射泵 single cylinder fuel injection pump圆柱式燃油喷射泵 cylindrical fuel injection pump旋转式燃油喷射泵 rotary fuel injection pump分配式燃油喷射泵 distributor fuel injection pump多缸燃油喷射泵 multicylinder fuel injection pump框架安装式燃油喷射泵 cradle mounted injection pump喷油始点 fuel injection beginning喷油终点 fuel injection end喷油持续角 fuel injection duration angle喷油延迟 injection delay引燃喷射 pilot injection启喷压力 injection starting pressure峰值喷油扭矩 peak injection torque峰值喷油压力 peak injection pressure喷油泵油缸数目 number of cylinders of an injection pump 无气喷射 solid injection喷射正时 injection timing集中喷射 group injection喷油器 injector整体式喷油器 unit injector喷嘴 nozzle轴针式喷嘴 pintle type nozzle环槽式喷嘴 annular slot nozzle孔式喷嘴 hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴 orifice plate nozzle开式喷嘴 open nozzle闭式喷嘴 closed nozzle喷油提前器 timing advance unit喷射泵壳体 injection pump housing针阀 needle芯轴 central spindle喷嘴壳体 nozzle body针阀升程 needle lift喷嘴盖形螺母 nozzle cap nut喷油器壳体 nozzle holder突缘安装喷油器壳体 flanged-mounted injection nozzle holder 燃油喷射泵传动装置 transmision of an injection pump喷嘴锥体 nozzle hole cone柱塞 plunger柱塞套 barrel柱塞行程 plunger stroke喷孔 spray orifice海拔控制器 altitude control提前器飞锤 flyweight喷孔长径比 ratio of nozzle hole length nozzle diameter喷嘴液动力特性 nozzle hydrokinetic characteristics动态相位 dynamic phase喷孔面积 nozzle hole area喷嘴流通特性 nozzle flow characteristic喷油背压 injection back pressure高压油管 high pressure pipe平均喷油扭矩 mean injection torque喷油总效率 overall pumping efficiency峰值喷油压力 injection peak pressure预行程 prestroke收缩行程 retraction stroke燃油箱 fuel tank油箱盖 fuel tank油位表 fuel level gauge注油控制装置 fill control system汽油箱 gasoline tank( petrol tank)汽油供给管 gasoline feed pipe加油管 filler tube放油螺塞 drain plug吸油管 suction pipe刚性燃油管 rigid fuel pipe进油孔 fuel feed hole供油管 supply pipe通气管 bleeding pipe通气管 bleeding pipe泄油阀 spill valve泄油孔口 spill port进油阀 inlet valve最大油量限制器maximum fuel stop滴油 dribble燃油表 fuel gauge输油泵 feed pump燃油泵 fuel pump附装燃油箱中的电动燃油泵 tank-mounted eletric fuel pump 机械式燃油泵 mechanical fuel pump膜片式燃油泵 diaphragm fuel supply pump叶片式供油泵 vane fuel supply pump活塞式输油泵 piston type fuel supply pump齿轮式输油泵 gear fuel supply pump电动燃油泵 eletric fuel pump带真空泵的汽油泵 vacuum pump with fuel pump起动加油器 primer起动给油杆 primer lever燃油泵上体 fuel pump body燃油泵下体 fuel pump base燃油泵盖 bowl cover进油口接头fuel inlet neck出油口接头 fuel discharge port输出阀 delivery valve泵油元件 pump element回油阀部件 fuel return valve assembly化油器 carburetor化油器系统 carburetor circuit简单化油器 elementary carburetor单腔化油器 single-barrel carburetor双腔并动化油器 two-barrel dual carburetor双腔分动化油器 two-barrel duplex carburetor四腔化油器 four-barrel carburetor上吸式化油器 updaught carburetor下吸式化油器 downdraught carburetor平吸式化油器 horizontal carburetor侧吸式化油器 side-draft-carburetor高海拔补偿式化油器 altitude compensating carburetor 化油器附加器 adaptor carburetor双腔式化油器 twin-choke carburetor固定喉管式化油器 fixed venturi carburetor可变喉管化油器 variable venturi carburetor化油器接头 carburetor adaptor阻风门 choke valve阻风活塞 choke piston阻风板 choke plate自动阻风门 automatic choke阻风门拉钮 choke button电控自动阻风门 electric-assisted choke阻风管 choke tube喉管 venturi双重或三重喉管 double & triple venturi阻风门拉线 choke cable化油器小喉管 booster venturi浮子系 float system浮子 float环形浮子 annular float同心式浮子 concentric float浮子支销 float hinge pin浮子针阀 float needle valve阀针 valve needle浮子油面 float level浮子臂 float arm侧置浮子室式 side float type怠速阀 idle valve怠速针阀 idle needle省油器 economizer省油器阀 economizer valve辅助空气阀 auxiliary air-valve加速油井 accelerating well加速泵 accelerating pump加速泵喷嘴 accelerating pump nozzle油门 throttle手油门 hand throttle节气门操纵手柄 throttle control lever真空加浓器 vacuum booster加浓器 excess fuel device量孔体 jet block怠速量孔 idle metering jet主量孔 main metering jet剂量阀活塞 dosage valve piston空气量孔 air jet燃油滤清器 fuel filter沉淀杯 sediment bowl串联过滤器 in-line filter燃油箱内装过滤器 in-tank filter调速器 governor飞球式调速器 flyball governor调速器 governor飞球式调速器 flyball governor液压调速器 hydraulic governor真空转速调速器 vacuum speed governor惯性调速器 inertia governor离心调速器 centrifugal governor调速器重锤 governor weight空气滤清器及进排气系统 air cleaner and intake and exhaust sytem 空气滤清器 air filter冲压式空气滤清器 ram air clearner恒温控制式空气滤清器 thermostatic controlled air cleaner油浴式空气滤清器 oil bath air cleaner纸质空气滤清器 paper air clearner旋流管式空气滤清器 swirl tube air filter滤清器滤芯 filter element空气滤清器壳体 air filter housing空气滤清器盖 air filter cover滤清器密封圈 filter seal ring滤网 sieve滤纸盘或膜 filter paper disc or membrane进气和排气系统 intake and exhaust system排气管 exhaust pipe排气抽气管 exhaust extraction duct扫气泵 scavenging pump进气预热装置 intake preheater进气歧管 intake manifold进气歧管真空度 intake manifold vacuum冷式进气歧管 cold manifold冲压式进气歧管 ram intake manifold排气歧管 exhaust manifold脉冲式排气歧管 pulse exhaust manifold等压排气歧管 constant pressrue exhaust manifold排气歧管热量控制阀 exhaust manifold heat control valve超高度歧管 high-rise manifold升温横跨管道 heat crossover排气横跨管道 exhaust crossover预热点 hot spot阻风门加热器 choke heater热空气导流管 hot air duct隔热板 heat shield排气再循环阀 exhaust -gas-recirculation消声器 silencer进气消声器 intake silencer排气消声器 exhaust silencer金属垫片式消声器 steel pack muffler玻璃丝消声器 glass pack muffler空洞消声器 gutted muffler前排气管 front exhaust pipe尾管 tail pipe消声器联接管 intermediate pipe热空气管 hot air pipe曲轴箱通风管 crankcase bleed pipe隔声罩 acoustic hood进气消声器元件 silencer element真空泵 vacuum pump指示功率 indicated power指示热效率 indicated thermal efficiency指示油耗率 indicated specific energy consumption示功图 indicator diagram冷却系 cooling system风冷 air cooling水冷 water-cooling循环流冷却系cooling recovery system自然循环液冷却系统 natural circulation type cooling system热流循环液冷却系统 thermo-siphon circulation type cooling system 温差循环液冷却系统 gravity circulation water cooling system压力式水冷却系统 positive circulation cooling system加压式冷却法 pressure type cooling水泵循环冷却系统 pump circulation cooling system强制循环式化冷系统 forced-feed water circulation system封闭式液冷系统 sealed cooling system散热器 radiator片式散热器 finned radiator管式散热器 tubular radiator蜂窝式散热器 cellular radiator哈里逊式散热器 Harrison type radiator带板式散热器 ribbon type radiator上水箱 upper tank下水箱 lower tank涨溢箱 expansion tank散热器芯 radiator core之字形管散热器芯 film core管-片式散热器芯 fin and tube core散热器加水口盖 radiator filter cap压力式水箱盖 radiator-pressure cap蒸气-空气泄放阀 vapor-air release valve散热器护罩 radiator cowl散热器百叶窗 radiator shutter散热器保温帘 radiator roller blind散热片 cooling fin缸盖散热片 cylinder head fin缸体散热片 cylinder block fin控温装置 temperature regulating device恒温器 thermostat恒温器主阀 thermostat main valve恒温器旁通阀 thermostat by-pass valve恒温器挠性波纹筒 thermostat flexible bellows液体冷却设备 liquid cooling equipment水泵 water pump水泵体 pump casing水泵叶轮 water pump impeller旁通进水口 water by-pass inlet neck循环泵 circulating pump主进水口 water main inlet port出水口 water outlet port自调式水封 self-adjusting seal unit溢流管 overflow pipe导流板 deflector风扇 fan(blower)轴流式风扇 axial flow fan离心式风扇 centrifugal fan风扇壳体 blower casing风扇导流罩 fan cowl风扇毂 fan hub风扇叶片 fan blade风扇叶轮 blower impeller风扇导流定子 blower stator风扇皮带轮 fan pulley三角皮带 v-belt风扇护罩 fan shroud风扇叶轮叶片 impeller vane冷却用空气 cooling air风扇导流叶片 stator vane强制风冷 forced-air cooling自然风冷 natural air cooling风道 air ducting润滑系 lubrication system润滑 lubrication气缸上部润滑 upper cylinder lubrication 压力润滑 pressure-feed lubrication压力润滑法 forced lubrication自动润滑 automatic lubrication飞溅润滑 splash lubrication润滑周期 lubrication interval边界润滑 borderline lubrication曲轴箱机油油盘 crankcase oil pan油底壳 oil pan机油盘放油塞 sump plug集油器 oil collector机油泵 oil pump计量式机油泵 metering oil pump齿轮式机油泵 gear type oil pump转子式机油泵 rotor-type oil pump机油泵出油管 oil pump outlet pipe放油口 oil drain hole油道 oil duct断油开关 cut-off cock机油散热器 oil cooler机油滤清器 oil filter机油粗滤器 primary oil filter机油精滤器 secondary oil filter全流式机油滤清器 full-flow oil filter分流式机油滤清器 by-pass oil filter离心式机油滤清器 centrifugal oil filter整体式滤芯 integral filtering element细滤器滤芯 filter element滤清器壳 filter box滤片filtering disc机油减压器 oil pressure relief valve旁通阀 by-pass oil filter机油滤网 oil strainer加机油孔 oil filter cap滤芯轴 filter shaft刮片组件 cleaning edge机油量尺 dipstick机油滤网 oil strainer增压器 supercharger增压和扫气装置 pressure-charging and scavenging unit 增压装置 supercharging device涡轮增压器 turbo-charger气波增压器 comprex pressure wave supercharger增压器阻风阀 supercharger blast gate增压器调节容气量的旁通阀 supercharger control bypass 增压器叶轮 supercharger impeller惯性增压 inertia supercharging机械增压 mechanical supercharging涡轮增压 turbo-charging增压比 supercharge ratio增压压力 boost pressure增压中冷 inter-cooling中冷度 inter-cooling level增压度 supercharging level喘振 surge喘振线 surge line轴流式涡轮 axial-flow turbine脉冲进气 ram charging发动机试验 engine test发动机试验规程 engine test procedure发动机技术要求 engine technical requirements标准大气状况 standard atmospheric conditions大气压力 atmospheric pressure进气温度 inlet air temperature进气温度 inlet air temperature功率校正 power correction功率标定 power rating功率换算 power conversion校正系数 correction factor换算系数 performance test性能试验 performance test起动性能试验 starting ability test怠速试验 idle running test道路负荷试验 road load test各缸工作均匀性试验 cylinder variation test背压试验 back pressure test最低稳定工作转速试验 lowest continuous speed test with load 背部泄漏试验 back-leakage test调整试验 adjustment test热平衡试验 heat balance test快速磨损试验 accelerated wear test热冲击试验 thermo-shock test空载特性试验 no-load characteristic test模拟增压试验 simulated supercharging test停缸试验 cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验 exhaust analysis test突变负荷试验 sudden load change test稳定性试验 stability test单缸熄火试验 one cylinder shut off test例行检查试验 routine inspection test验证试验 verification test鉴定试验 approval test可靠性试验 reliability test耐久性试验 durability test定型试验 type approval test验收试验 acceptance test现场试验 field test出厂试验 delivery test抽查试验 spot check test复查试验 re-check test台架试验 bench test强化试验 hop-up test发动机试验台 engine test bed底盘测功机 chassis dynamometer测功机 dynamometer水力测功机 hydraulic dynamometer电涡流测功机 eddy current dynamometer电力测功机 electric dynamometer扭矩仪 torque meter转速表 tachometer温度测量 thermometry温度测量仪器 thermometric instruments空气流量测量 air flow measurement热线风速仪 hot wire anemometer电子示功仪 electronic indicator燃烧分析仪 combustion analyzer压力传感器 pressure transducer精密声级计 precision sound level meter排放 emission排放物 emission排气污染物 gaseous pollutant蒸发排放物 evaporative emission曲轴箱排放物 crankcase emission漏气 blowby gas氨氧化物 oxids of nitrogen一气化碳 carbon monoxide碳氢化合物 hydrocarbon甲烷 methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物 photochemically reactive hydrocarbons 微粒物 particulated matter黑烟 black smoke蓝烟 blue smoke白烟 white smoke碳烟 soot光化学烟雾smog臭味 odor丙烷 propane排放浓度 concentration of emission排气烟度 exhaust smoke先期排气 initial exhaust亚临界排气 subcritical exhaust超临界排气 supercritical exhaust强制排气 forced exhaust自由排气 free exhaust排气提前角 exhaust advance angle排气迟后角 exhaust lag angle排气热损失 exhaust heat loss排气净化 exhaust purification排气背压 exhaust back pressure残余废气 residual gas排气有害成分 poisonous exhaust composition柴油机排烟 diesel smoke综合排放浓度 composite concentration of exhaust emission 综合排放质量 composite mass of exhaust emission排放系数 emission factor排放率emission index质量排放量 mass emission比排放量 brake specific emission排放物控制系统 emission control system排气排放物控制系统 exhaust emission control system二次空气 secondary air二次空气分配歧管 secondary air distribution二次空气控制阀 secondary air control valve二次空气转换阀 secondary air switching valve二次空气转流阀 secondary air diverter valve二次空气喷射装置 secondary air injection system二次空气喷射管 secondary air injection tube二次空气喷射减速压阀 secondary air injection relief valve 脉动空气装置 pulsating air system二次空气泵 secondary air pump曲轴箱排放物控制系统 crankcase emission control system曲轴箱双通风系统 crankcase closed system曲轴箱单通风系统 crankcase sealed system曲轴箱强制通风装置 positive crankcase ventilationPCV阀 PCV valve蒸发排放物控制系统 evaporative emission control system活性碳罐贮存装置 charcoal canister storage system活性碳罐 charcoal canister曲轴箱贮存装置 crankcase storage system空气滤清器贮存装置 air filter storage system燃油箱止回阀 fuel tank check valve油气分离器 fuel and vapor separator清除阀 furge valve催化转化系统 catalytic converting system催化燃烧分析仪 catalytic combustion analyzer催化剂 catalyst转化器 converter催化转化器 catalytic converter轴流式转化器 AXIAL FLOW TYPE CONVERTER径流式转化器 RADIAL FLOW TYPE CONVERTER下流式转化器 down flow type converter上流式转化器 up flow type converter双床式转化器 dual bed converter单床式转化器 single bed converter氧化型催化剂 oxidation catalyst还原型催化剂 reduction catalyst三元催化剂 three-way catalyst贵金属催化剂 noble metal catalyst。

(整理)发动机专业英语单词.

Para 1 基本原理Notes:Para.1.appreciate: understand fully，评价，估价，理解unsuitability :不适合，不相称，不匹配present:submit,offer,give，提出，设置2.patent: n,专利v,取得…专利athodyd: 航空热力管道，冲压式喷气发动机ram jet: 冲压喷气发动机3.turbo-propeller engine: 涡轮螺桨发动机viscount aircraft: 子爵式飞机twin-spool: 双转子triple-spool: 三转子by-pass: 双涵式，内外涵ducted fan: 管道风扇式,涵道风扇式4.piston engine: 活塞发动机solely:单独地,独自地,只是5.pulse jet: 脉动式发动机turbo/ram jet: 涡轮/冲压喷气发动机6.momentum: 动量issue:流出,放出impart…to…:give，给予jet: 喷嘴8.sprinkler: 喷水器by virtue of: 凭借，利用firefighting: 消防hose: 软管carnival: 狂欢节9.resultant: 合成的，总的10.convert…into…:change…into，11.convergent: 收敛的divergent: 发散的target vehicle: 耙机12.intermittent: 间歇的，周期性的static：静止的，静态的dynamic：动力的，动态的aero-：空气的aerodynamic：空气动力学的robust：坚固的，强壮的spring-loaded：绷有弹簧的(图1-7)：shutter valve：薄片式，快门式阀门，节气活门depression：下降rotor：旋翼helicopter：直升机dispense with：免去，不用resonate：共振，谐振13.decompose：分解14.inherent：内在的，固有的up to：直至，高达（上限）15.somewhat：比较，有点blade：叶片16.blade-tip：翼尖departure from:偏离，违背17.offset：补偿，弥补，冲淡18.Mach number：马赫数19.variable intake：可调进气道afterburner：加力燃烧室shut down：停车，关闭guide vane：导向叶片divert：redirectsustained：stable，稳定的，持续的cruise condition：巡航状态20.alternative：另一种结构型式21.kerosine：煤油multi-stage：多级in the order of ：数量级22.interceptor：截击机space-launcher：航天飞机high altitude：高空short duration：短的巡航时间Part 2工作循环和空气流动1.efflux：射流，流出，涌（迸）出2.stroke：冲程reciprocate：往复式的3.fabricated：板金焊接的（板料）4.remainder：剩余物5.assembly：组件7. embody：包含（contain）product：乘积extract：取出（功），吸收（功）9.trace through：追踪，指示10.attain：到达（achieve）11.adiabatic：绝热的friction：摩擦conduction：导热，热传导turbulence：湍流，扰动12.propelling nozzle：推进喷管deceleration：减速acceleration：加速13.convert(convertion)…to(into)…supersonic：超音速的transonic：跨音速的subsonic：压音速的encounter：遭遇，遇到14.failure：损坏，失效vibration：振动eddy：旋涡15.straight-through flow system：直流系统frontal area：迎风面积subsequent：后续的（following）17.conducive：有助（益）于，促进…的specific：单位的，比的（如specific heat，比热）specific fuel consumption：耗油率18.configuration：机构，构造，结构型式19.overboard：出去，向…外variation：变形Part 3 压气机Para.1.centrifugal：离心的axial：轴向的shaft：轴2.impeller：叶轮diffuser：扩压器3.with regard to：关于，对于，论及，提及4.specific thrust：单位推力5.casing：机匣plenum chamber：稳压腔6.radially：辐射地，径向地initially whirl：预旋8. tip speed：叶尖速度9.leakage：泄露clearance：间隙，公差10.ball bearing：滚珠轴承roller bearing：滚棒（柱）轴承ease of detachment：易于拆卸11.forged disc：铸造盘，铸件sweep back：回弯12.all-round efficiency：圆周效率surge：喘振ram effect：冲压效应13.tangential：切向的aerodynamic buffeting impulses：气动抖振14.aerofoil：气动翼型angular setting of the vanes：叶片安装角inlet guide vanes：进口导流片15.air annulus area：空气环形流道面积tapering：作成锥形17. operating flexibility：最佳速度20.correct the deflection：工作适应性air straightener：空气整流器21.air breakaway：气流分离blade stall：叶片失速22.tortuous：曲折的，扭曲的culminate：vi，达到顶点，以…告终25.alignment：准直，对中26.drum-type：鼓筒式disc-dype：盘式spline：花键，用花键连接spacer rings：垫圈blade platform：叶片榫缘27. rock：摇动，摇摆28. angle of incidence：倾角，迎角29.retaining rings ：?固定环，保持环in packs：成组，成批shroud：叶冠，加叶冠32.blade profile：叶片型面flight manoeuvre：飞行机动，飞行动作ingestion：吸入外物34. off design speed：非设计转速35.cough：咳嗽a bang of varying severity：忽强忽弱的放炮声36.safety margin：安全裕度37.bleeding：放气，以…抽气减压38.pneum(o)-：[词头]空气，气动，呼吸pneumonia：肺炎pneumatic：气动的choking：阻塞39.actuator：作动筒，促动筒r.p.m.= revolution per minute40.fatigue resistance：耐疲劳42. titanium：钛carbon or glass fiber composite：碳或玻璃纤维复合材料43.magnesium：镁44.engines designed entirely for lift：升力发动机45.balancing：平衡in view of：由于，鉴于，考虑到Part 4 燃烧室Para.mercial aircraft traffic：民用航空exhaust smoke：排气烟带4.normal：额定的blow away：吹熄5.flame tube：火焰筒liner：套筒（管）meter：量度，测量，定量multi-meter：万用表-meter：仪表，仪器6.snout：主进气口，飞机头部swirl vane：扰流器（叶片）perforated flare：多孔漏斗recirculation：回流air casing：燃烧室外套7.toroidal vortex：环形涡流anchor：驻定，抛锚8.break up：破碎，弄细9.nozzle guide vanes of the turbine：涡轮导向器叶片dilution：稀释10.igniter plug：电嘴点火器self-sustained：自行保持的13.atomizer jets：雾化喷嘴vaporizing principle：汽化原理，蒸发原理baffle plate：隔板14.multiple chamber：单管燃烧室tube-annular chamber：环管燃烧室annular chamber：环型燃烧室17. interconnector：联焰管18.overhaul：大（翻）修compactness：结构紧凑21.decrease by：减小了decrease to：减小到22.air spray type burner：气动喷嘴aerate：充（通）气，吹气over-rich pockets of fuel vapour：过富的燃油蒸气，油兜，油井（穴），油带24. flame extinctior：熄火25.incur：招致，遭受（损失，坏结果）30.glide：滑翔dive：俯冲idling：慢车rich limit：富油极限weak limit：贫油极限mixture strength：混合物浓度31.loop：包线33. negligible：可忽略的35.creep failure：蠕变stress：应力strain：应变Part 5 涡轮Para.2.torque：力矩stationary：静止的，固定的moving：运动的with the advent of：随着…到来，出现3.shaft-power engine：涡（轮）轴发动机free-power turbine：动力涡轮reduction gear：减速齿轮（器）interpose：介入，插入promise：妥协，协调，调和power/weight ratio：功重比patible with：与…相适应的，相容的juxtaposition：排列位置pure impulse turbine：纯冲击式涡轮pure reaction turbine：纯反作用式涡轮incorporated：合并，加入，包含，包括，采用cartridge and air starters：火药式和空气式起动机7. discharge：流出8. detrimental：有害的exhaust cone supports and struts：排气锥支座与支板9.stagger angle：叶片扭转角-安装角10.degree of reaction：反力度12. self-aligning coupling：自调联轴器15.machined forging：机加铸件flange：安装边，法兰盘perimeter：周长18.permitted stress：许用应力trailing edge：后缘leading edge：前缘crack：裂纹19.has an important bearing on：对…有重要影响，关系limiting rim speed：极限轮缘速度de laval bulb root fixing：特拉瓦球形叶根固定（法）be superseded by：以…代替（取代）…‘fir-tree’ fixing：枞树形固定（法），枞树形榫齿serration：榫齿，锯齿stiffen：拉紧，加强hollow：空心的20.segment：扇形段peripheral：圆周的，周边的peri-：圆周的，周边的22. flow characteristics：流量特性back pressure：反压，背压24. creep life：蠕变寿命creep characteristics：蠕变特性26.bending loads：弯曲载荷thermal shock：热冲击high frequency fluctuations：高频振荡28. foregoing = above, preceding29ferritic：铁素体的，三价铁的ferro-：亚铁的austenitic：奥氏体的nickel：镍Part 6 排气系统Para.3.thrust reverser：反推力装置noise suppressor：消音器mixer unit：混合器4.support fairings：整流支板7. longitudinal axis：纵轴9. flap：折叶，片状物，调节片nozzle aperture：喷口孔板10. r.p.m. = revolutions per minute：每分钟转速12. special heat-resisting steels：特殊耐高温钢lag：铺设，包上insulating blanket：绝热层fibrous：纤维dimple：起皱纹，生微涡13.engine nacelle：发动机短舱14.streamlined fairings：整流支板vent hole：通气孔15.chute：进气漏斗Part 7 消音器Para.1.annoyance level：扰人程度perceived noise decibel(PNdB)：能听到的噪音，分贝pitch：音调2.to some power：成幂次关系x to the power nthe nth power of x4. wake：尾流，涡流discrete：断续的，离散的harmonics：谐波5.approach thrust：进场推力6.obviate：排除，免除，事先预防7.lobe-type：叶瓣形9. weight penalty：重量损失11. optimum mean noise level：最佳平均噪音强度12. the pilot’s master switch：驾驶员主控开关pneumatic rams：气动作动筒charge-over：转换13. honeycomb backing：蜂窝芯14. provision：装置（调整机构）15. noise radiation：噪音传播16. sintered fibrous-metallic materials：烧结的纤维金属材料Part 8Para.1. wheel brake：机轮刹车braking parachutes：阻力伞2. landing run：着陆滑跑距离(图) I.S.A.= International Standard Atmosphere：国际标准大气4. pitch：安装角throttle lever：油门杆（操纵杆）7. clamshell-type：蛤壳形retractable ejector：伸缩式作动器bucket-type：库斗式blocked doors：阻塞门9. cascade vanes：叶栅10. linkage：连杆11. latch：锁住12. divert：使转向，使变换方向13. flexible drives：钢索传动，挠性传动装置screwjack：丝杠translating：平移变换，移动cowl：整流罩flush：齐平地fairing：整流罩16. safety features：安全（特性）措施crew compartment：驾驶舱17. pitch control system：桨距调节系统trim：调节，微调malfunction：失灵，出故障20. hinged：铰接22. in segments：成组roller：滚轮23. rod：连杆buffet：冲击stiffen：加强Para.1. afterburning：补燃加力3. afterburner：加力燃烧室burner：喷嘴（喷灯）(图) sleeve：套筒6. stabilizer：火焰稳定器interconnection：联焰7. normal：额定的lit：light的过去分词8. catalytic：催化的platinum-based dement：铂基原件hot streak of flame：热射流hot-shot ignition：热射式点火9. cool flame：冷焰at sea levelat altitude13. boost：增加，提高15. pressure ratio control unit：压比调节器16. gear type pump：齿轮泵17. be relayed to：传给，中继degree of afterburning：加力程度20. eyelid：喷口21. struts：支板22. circular heat shield：环形隔热屏perforated：钻孔Para.1. with the exception of：except, apart from，除了…以外shut-off valve(cock)：截止阀，截止开关throttle or power lever：油门杆或功率杆2. prevent…for…：防止3. pitch：螺距，桨距overspeeding：超转，超速governor：调节器，控制器4. ancillary function：辅助功能7. gear-type pump：齿轮泵variable-stroke：可变行程multi-plunger：多柱塞式图10-1：knot：结，海里/小时8. free-power turbine：自由动力涡轮11. spill valve：溢流阀，泄流阀14. bleed：放，泄（油，气，水），回油capsule：膜片I.S.A.：国际标准大气15. centrifugal：离心的rotor radial drilling：转子径向孔diaphragm：膜片F.C.U. = flow control unit：流量控制装置16. safety relief valve：安全回油活门regardless of：不论，不管17. dashpot throttle unit：阻尼油门装置ported sleeve：有开孔的套筒rack and pinion：齿轮齿条副（传动）20. annulus：环形通道restrictor：限制器spray nozzle：喷嘴22. capsule assembly：膜片组件evacuated capsule：真空膜片pump stroke：油泵行程23. specific gravity：比重24. centrifugal loading：离心载荷26. solenoid valve：电磁阀27. starting nozzle：起动喷嘴igniter plug：火花塞28. back pressure valve：反压阀门30. trimming device：微调装置31. opposing jets：对置喷嘴interrupter blade：遮断叶片33.proportioning valve：比例活门35. equalize：使…相等37. surge：喘振inertia：惯性time lag：时间滞后override：占优势，超控38. metering plunger：节流柱塞overfuelling：过量供油45. L.P. side of the drum：鼓筒的低压端46. rocker arm：摇臂48. idling speed governor：慢车转速调节器49. overstressing：过应力50. relight：再点火51. all-speed：全转速fuel flow regulator：燃油流量调节器main burner：主喷嘴52. gear train：齿轮泵variable metering sleeve：可变节流套筒cam：凸轮stirrup arm：托架臂58. stop：止动销60. thermocouple：热电偶rotary actuator：旋转作动筒62. main burner manifold：主燃油喷嘴总管flyweight：配重63. main and primary flows：主燃油和初级燃油64. water injection：喷水reset cam：重调凸轮72. trimmer valve：微调活门75. air off-take：空气取出，空气提取77. vapour locking：气阻（汽化阻塞）cavitation：气穴ice crystal：冰晶filter：过滤器oil cooler：滑油散热器transmitter：传感器78. plunger-type pump：柱塞式泵constant-delivery gear-type pump：等排量齿轮泵81. camplate：凸轮盘inclination：斜度84. atomize：使…雾化swirl chamber：旋涡室85. simplex：单油路喷嘴lubbock：可调进口喷嘴duplex or duple：双油路喷嘴86. square law：平方律91. exhaust smoke：排气冒烟92. flow distributor：流量分配器gravity head：重力压头94. fuel-cooled oil cooler：燃油冷却的滑油散热器thermostatically：恒温的，热静力学的98. buoyant material：轻浮材料100. conform to：与…一致overhaul：翻修wide-cut gasoline-type fuel：宽馏分汽油型燃油102. viscosity or thickness：粘度或稠度anti-icing additives：防冰添加剂103. volatility：挥发性104. British Thermal Unit：英热单位calorific value：热值105. sulphurous acid：硫酸107. distillation：蒸馏flash point：闪点110. inert gas：惰性气体112. tank drain check：油箱放油检查Part 11 Para.1. methanol：甲醇methane：甲烷5. metering valve：量孔，计量阀门servo：伺服，随动，助力capsule assembly：膜盒组件6. oil cock：滑油开关throttle：油门7. feed arm：供油臂swirl vane：扰流器governor：调节器8. pressure difference：压差9. non-return valve, one-way valve：单向阀门Part 13 Para.1. main bearing housings：主轴承座drive-shaft seals：传动轴封严装置2. disperse：分散，散开vent：排出，泄放，通风overboard：机外ventilate：通风4. interstage：级间multi-groove construction：齿结构5. pre-swirl feed：预旋供气6. clearance：间隙7. de-aerator system：油气分离系统breather：通风器9. thermo-couple：热电偶temperature gauge：温度表10. intake louvres：进口导风板cowling：整流罩11. undercarriage：起落架12. engine bay or pad：发动机短舱extinguishant：灭火剂13. bulkhead：隔舱15. drain pipe：漏油管，泄油管。

发动机专业英语词汇

发动机分类1 往复式内燃机reciprocating internal combustion engine2 化油器式发动机carburetor engine3 转子发动机rotary engine4 旋轮线转子发动机rotary trochoidal engine5 二冲程发动机two-stroke engine6 四冲程发动机four-stroke engine7 增压式发动机supercharged engine8 风冷式发动机air-cooled engine9 油冷式发动机oil-cooled engine10 水冷式发动机water-cooled engine11 自然进气式发动机naturally aspirated engine12 煤气机gas engine13 液化石油气发动机liquified petroleum gas engine14 柴油煤气机diesel gas engine15 多种燃料发动机multifuel engine16 石油发动机hydrocarbon engine17 双燃料发动机duel fuel engine18 热球式发动机hot bulb engine19 多气缸发动机multiple cylinder engine20 对置活塞发动机opposed piston engine21 对置气缸式发动机opposed-cylinder engine22 十字头型发动机cross head engine23 直列式发动机in-line engine24 星型发动机radial engine25 筒状活塞发动机trunk-piston engine26 斯特林发动机stirling engine27 套阀式发动机knight engine28 气孔扫气式发动机port-scavenged engine29 倾斜式发动机slant engine30 前置式发动机front-engine31 后置式发动机rear-engine32 中置式发动机central engine33 左侧发动机left-hand engine34 右侧发动机right-hand engine35 短冲程发动机oversquare engine36 长冲程发动机undersquare engine37 等径程发动机square engine38 顶置凸轮轴发动机overhead camshaft engine39 双顶置凸轮轴发动机dual overhead camshaft engine40 V形发动机V-engine41 顶置气门发动机valve in-head engine42 侧置气门发动机side valve engine43 无气门发动机valveless engine44 多气门发动机multi-valve engine45 卧式发动机horizontal engine46 斜置式发动机inclined engine47 立式发动机vertical engine48 W形发动机w-engine49 I形发动机I-engine50 L形发动机L-engine51 F形发动机F-engine52 原机Engine prototype发动机性能53 二冲程循环two-stroke cycle54 四冲程循环four-stroke cycle55 狄塞尔循环diesel cycle56 奥托循环otto cycle57 混合循环mixed cycle58 定容循环constant volume cycle59 工作循环working cycle60 等压循环constant pressure cycle61 理想循环ideal cycle62 热力循环thermodynamic cycle63 冲程stroke64 活塞行程piston stroke65 长行程long stroke66 上行程up stroke67 下行程down stroke68 进气行程intake stroke69 充气行程charging stroke70 压缩行程compression stroke71 爆炸行程explosion stroke72 膨胀行程expansion stroke73 动力行程power stroke74 排气行程exhaust stroke75 膨胀换气行程expansion-exchange stroke76 换气压缩行程exchange-compression stroke77 上止点top dead center(upper dead center)78 下止点lower dead center(bottom dead center)79 上止点前budc(before upper dead center)80 上止点后atdc(after top dead cetner)81 下止点前bbdc(before bottom dead center)82 下止点后abdc(after bottom dead center)83 排气量displacement84 发动机排量engine displacement85 活塞排量piston swept volume86 气缸容量cylinder capacity87 单室容量single-chamber capacity88 容积法volumetry89 压缩比compression ratio90 临界压缩比critical compression ratio91 膨胀比expansion ratio92 面容比surface to volume ratio93 行程缸径比stroke-bore ratio94 混合比mixture ratio95 压缩压力compression pressure96 制动平均有效压力brake mean effective pressure(bmep)97 空燃比air fuel ratio98 燃空比fuel air ratio99 燃料当量比fuel equivalence ratio100 扭矩torque101 单缸功power per cylinder102 升功率power per liter103 升扭矩torque per liter104 升质量mass per liter105 减额功率derating power106 输出马力shaft horsepower107 马力小时，马力时horsepower-hour108 总马力gross horse power109 总功率gross power110 净功率net power111 燃油消耗量fuel consumption112 比燃料消耗率specific fuel consumption113 空气消耗率air consumption114 机油消耗量oil consumption115 有效马力net horse power116 额定马力rated horse power117 马力重量系数horsepower-weight factor118 制动功率brake horse power119 制动热效率brake thermal efficiency120 总效率overall efficiency121 排烟极限功率smoke limiting horsepower122 功率曲线power curve123 机械损失mechanical loss124 机械效率mechanical efficiency125 有效热效率effective thermal efficiency126 充气系数volumetric efficiency127 过量空气系数coefficient of excess air128 适应性系数adaptive coefficient129 扭矩适应性系数coefficient of torque adaptibility130 转速适应性系数speed adaptive coefficient 131 强化系数coefficient of intensification132 校正系数correction factor133 换算系数conversion factor134 活塞平均速度mean piston speed135 发动机转速engine speed (rotational frequency) 136 充量（进气）charge137 旋转方向direction of rotation138 顺时针clockwise139 逆时针counter-clockwise140 左转left-hand rotation141 右转right-hand rotation142 发动机性能engine performance143 加载性能loading performance144 起动性能starting performance145 加速性能acceleration performance146 动力性能power performance147 排放性能emission performance148 燃油经济性Fuel economy149 排放Exhaust emissions150 大的燃烧噪声Large combustion noise151 预混合燃烧Premixed combustion152 扩散燃烧Diffusion combustion153 大的EGR率Heavy EGR154 推迟喷油时间Retarding the injection timing, 155 推迟喷油时间Delaying the fuel injection timing, 156 燃烧激振力Combustion excitation forces (CPL) 157 CO2排放Carbon dioxide (CO2) emissions158 温室气体Greenhouse gas159 热效率Thermal efficiency160 辅助涡流室Auxiliary swirl chamber161 黑烟Black smoke162 Nox氮氧化物Nitrogen oxides163 PM颗粒物Particulate matter164 EGR废气再循环Exhaust gas recirculation165 燃油供给系统The fuel injection system166 在低负荷区In the low load region167 气缸压力The cylinder pressure level168 曲轴转角The crank angle169 1/3倍频程1/3 octave band of the frequency 170 全负荷Full load171 部分负荷Partial load172 声压级Sound pressure level173 发动机扭矩Engine torque174 燃烧噪声Combustion noise175 机械噪声Mechanical noise176 涡轮增压的Turbocharged177 涡轮增压器Turbocharger178 着火燃迟期The ignition delay period179 喷油泵The fuel injection pump180 增压中冷柴油机Intercooled turbocharged diesel181 碳化氢Hydrocarbon (HC)182 进气管几何尺寸Intake port geometry183 水平轴Horizontal axis184 声功率Sound power level185 竖直轴Vertical axis186 辐射噪声Radiation noise187 发动机测功机engine dynamometer188 零负荷到中等负荷Idling to a medium-load189 振幅Amplitude190 气缸体振动Cylinder block vibration191 声压级Sound pressure level192 随着曲轴转角In relation to the crank angle193 最大汽缸压力The maximum cylinder pressure194 最大汽缸压力升高率The cylinder pressure gradient195 共轨系统Common-rail system196 可变喷嘴涡轮增压器variable nozzle turbocharger197 引导喷射pilot injection198 4气门DOHC系统4-valve DOHC system199 计算机辅助工程CAE computer-aided engineering200 固有噪声Born noise201 侧面挠度lateral bending202 排气岐管exhaust manifold203 进气岐管intake manifold204 交流发电机alternator205 齿轮箱gear case206 供油泵supply pump207 起动机starter208 共振频率resonance frequency209 气缸压力快速升高率the rapid rising rate of cylinder pressure 210 主喷量和主喷时间main injection volume, timing211 共轨油压fuel pressure in a common-rail212 放热率heat release ratio213 步进电机step-motor214 频谱图frequency spectrum map215 油膜oil film216 机械噪声mechanical noise217 识别identify218 变量variable219 隔离声音的传播途径Isolate sound transmission routes 220 衰减Attenuation221 半消声室Semi-ane choic chamber222 系数Coefficient223 正时带Timing belt224 台架实验Bench test225 气门驱动凸轮Valve-drive cam226 传递系数Transfer coefficient227 矢量vector228 气穴现象Cavitation229 微处理器microprocessor230 执行器actuator231 电控泵electronically controlled pump构造232 气缸盖cylinder head233 气缸体cylinder block234 整体铸造cast inblock (cast enblock)235 发动机罩engine bonnet236 气缸体加强筋engine block stiffening rib237 气缸cylinder238 示功图indicator chart/diagram239 缸体（转子机）stator240 缸径cylinder bore241 气缸体机架cylinder block frame242 配气机构箱valve mechanism casing243 气缸体隔片cylinder spacer244 气缸盖密封环cylinder head ring gasket245 气缸盖垫片cylinder head gasket246 气缸套cylinder liner(cylinder sleeve)247 干式缸套dry cylinder liner248 湿式缸套wet cylinder liner249 气缸水套water jacket250 膨胀塞expansion plug251 防冻塞freeze plug252 气缸壁cylinder wall253 环脊ring ridge254 排气口exhaust port255 中间隔板intermediate bottum256 导板guideway257 创成半径（转子机）generating radius258 缸体宽度（转子机）operating width259 燃烧室combustion bowl260 浅盆形缩口燃烧室shallow reentrant combustion chamber 261 主燃烧室main combustion chamber262 副燃烧室subsidiary combustion chamber263 预燃室prechamber264 涡流燃烧室` swirl combustion chamber265 分开式燃烧室divided combustion chamber266 涡流式燃烧室turbulence combustion chamber267 半球形燃烧室hemispherical combustion chamber268 浴盆形燃烧室bathtub section combustion chamber269 L 形燃烧室L-combustion chamber270 楔形燃烧室wedge-section combustion chamber271 开式燃烧室open combustion chamber272 封闭喷射室closed spray chamber273 活塞顶内燃烧室piston chamber274 爆发室explosion chamber275 燃烧室容积比volume ratio of combustion cahmber276 发动机托架engine holding frame engine277 动力机装置power unit278 直喷柴油机DI（direct-injection）diesel engine279 非直喷柴油机IDI（Indirect-injection）diesel engine 280 动力传动系power train281 连杆connecting rod282 油底壳oil pan283 活塞销piston pin284 气缸套cylinder bore285 凸轮齿cam gear286 空气室energy chamber287 气缸余隙容积cylinder clearance volume288 燃烧室容积combustion chamber volume289 气缸最大容积maximum cylinder volume290 压缩室compression chamber291 外径major diameter292 中径pitch diameter293 内径minor diameter294 径向间隙radial clearance295 两极调速器limiting_speed governor296 特性297 空转特性no load characteristics298 负荷特性part throttle characteristics（汽油机）load characteristics299 调速特性governor control characteristics300 万有特性mapping characteristics301 稳定调速率steady state speed governing rate工况302 怠速转速idling speed303 经济转速economic speed304 起动转速starting speed305 最低稳定工作转速lowest continuous speed with load306 最大扭矩转速speed at maximum torque307 最高空转转速maximum no load governed speed308 调速speed governing309 超速overspeed310 怠速idling311 转速波动率speed fluctuation rate312 工况working condition(operating mode)313 额定工况declared working condition314 变工况variable working condition315 稳定工况steady working condition316 空载no-load317 全负荷full load318 超负荷overload319 部分负荷part load320 怠速控制idling-speed control321 怠速工况idling condition322 起动工况starting condition323 起动转速cranking speed324 急减速工况abrupt decreasing condition325 加速工况accelerating condition326 驻车park327 调速Speed governing328 应急[跛行]模式limp-in mode排放329 Emission Standards in the EU 欧洲排放标准330 Fuel Quality 燃油质量331 Conformity of Production (COP) 生产一致性检测332 Fuel Consumption 燃油消耗333 Exhaust Emission Measurement 排放检测334 tailpipe 排气管335 Carbon monoxide 一氧化碳336 emissions of crankcase gases 曲轴箱燃油蒸发排放量337 Ageing test 耐久性试验338 EPEFE = European Program on Emssions, Fuels and Engine Technologies 欧洲的排放、燃油及发339 动机技术项目340 fuel properties 燃油质量341 Car Manufacturers 汽车制造商342 Impact of vehicle emissions on air quality 排放对空气质量的影响343 Cetane no. 十六烷值344 Evaporation characteristic 蒸发特性345 Sulfur-free Fuels 无硫燃油346 Testcycle 测试循环347 NEDC = New European Driving Cycle 新的欧洲标准测试循环348 Loading of charcoal canister 炭罐吸附349 preconditioning (PC) 预处理350 ESC=European steady state cycle 稳态循环351 ELR=European load response test 负荷烟度试验352 ETC=European transient cycle瞬态循环353 EEV=Enhanced Environmentally Friendly Vehicle 环境友好汽车354 ambient temperature 环境温度355 λ-sensor λ传感器356 exceeding emission limits) 排放超出限值357 Roadworthiness-Tests 道路适应性检测358at free acceleration 在自由加速工况下359 catalyst 催化转化器360 natural aspirated 自然吸气机型361 turbo charged 涡轮增压机型362 Emission Control Technologies 排放控制技术363 Three-way catalyst 三元催化转化器364 catalyst coating 催化转化器涂层365 secondary air injection 二次空气喷366 exhaust gas recirculation 排气再循环系统367 oxidation catalyst 氧化催化转化器368 piezo injection valves 压电式喷油阀369 PowerStations 发电机组370 Anthropogenic 人为因素371 ACEA = European Car Manufacturer Association 欧洲汽车制造商协会372 Target corridor 标范围373 Target value目标值374 CFV 临界流量文丘里管（Critical flow venturi）375 CLD 化学发光检测器（Chemiluminescent detector）376 FID 氢火焰离子化检测器（Flame ionisation detector）377 GC 气相色谱仪（Gas chromatograph）378 HCLD 加热式化学发光检测器（Heated chemiluminescent detector）379 HFID 加热式氢火焰离子化检测器（Heated flame ionisation detector）380 LPG 液化石油气（Liquefied petroleum gas）381 NDIR 不分光红外线分析仪（Non-dispersive infrared analyzer）382 NG 天然气（Natural gas）383 NMC 非甲烷截止器（Non-methane cutter）384 Rated power 额定功率。

航空发动机常用汉英词汇.

汉英分类词汇航空发动机类型Aero-Engine Models超高涵比发动机ultra high bypass engine超音速冲压喷气发动机scramjet engine冲压喷气发动机ram-jet engine带推力转向系统的发动机engine with thrust deflector system带自由涡轮双轴涡轮轴喷气发动机twin-spool turbo-shaft with free-power turbine单轴涡轮喷气发动机single-spool turbo-jet engine低涵比发动机low bypass turbofan反向旋转发动机contra-rotation engine高涵比发动机high bypass turbofan后风扇涡轮喷气发动机aft fan turbo-jet engine 活塞式发动机piston(-and-cylinder) engine // piston-driven engine桨扇发动机prop-fan engine离心涡轮喷气发动机centrifugal turbo-jet engine 脉冲喷气发动机pulse jet engine前风扇涡轮喷气发动机front fan turbo-jet engine 燃气轮机gas turbine engine三轴桨扇发动机three-shaft prop-fan engine三轴涡轮前风扇涡轮发动机triple-spool front fan turbo-jet双轴外涵涡轮喷气发动机twin-spool by-pass turbo-jet双轴涡轮风扇发动机twin-spool turbo-fan engine 同向旋转发动机co-rotation engine外骨架发动机exo-skeletal engine涡轮冲压喷气发动机turbo/ram jet engine涡轮风扇发动机turbofan engine涡轮火箭发动机turbo-rocket engine涡轮螺旋桨发动机turboprop engine涡轮喷气发动机turbojet engine涡轮轴发动机turbo-shaft engine轴流涡轮喷气发动机axial flow turbo-jet engine 型面profile型面座标图aerofoil ordinate chart型式form轴流式压气机axial (flow) compressor函道duct函道比by-pass函道风扇ducted-fan中介机匣intermediate case燕尾形样dovetail root叶片vane（一般指静子叶片）压气机compressor压气机机匣compressor case效率efficiency压气机盘compressor disc压缩比compression ratio牙底root涡轮导向器turbine nozzle涡轮盘turbine disc燃烧室burner // combustion chamber //combustor燃烧室外套combustion outer case燃油导管discharge nozzle燃油滤fuel filter燃油喷咀fuel atomizer // fuel spray nozzle燃油消耗量fuel consumption火焰筒liner扩散器机匣diffuse case加力燃烧室afterburner航空发动机叶片术语Terms of Aero-Engine Airfoils叶片类型Type of Airfoils动叶blade // bucket静叶vane空心叶片hollow blade // core blade实心叶片solid blade涡轮导向器turbine nozzles涡轮导向器扇形段turbine nozzle segment涡轮导向器叶片turbine nozzle vane // nozzleguide vane (ngv)涡轮工作叶片turbine blade // bucket涡轮静子叶片turbine nozzle vane // nozzle guidevane (ngv)涡轮叶轮turbine wheel涡轮叶片turbine blades & vanes // buckets涡轮转子叶片turbine blade // bucket压气机定子叶片compressor vane // vane压气机工作叶片compressor blade // blade压气机叶轮compressor impeller // compressorwheel压气机叶片compressor blades & vanes压气机整流叶片compressor vane // vane压气机转子叶片compressor blade // blade叶片的结构特点Characteristics of Airfoil Structure283基体部分base榫头tip // cog // fir-tree // root // tenon叶根blade root // root // vane tang叶冠shroud // tip platform // tip shroud叶身blade body叶型部分aerofoil // profile缘板platform // shroud叶片的主要名称Key Terms of Airfoil Body基体base进气边/前缘leading edge理论叶型theoretical developed airfoil/profile排气边/后缘trailing edge // exhaust edge弦chord型线airfoil curve叶背blade back // convex side // blade convex叶盆blade basin // vane basin // blade/vane concave叶片阻尼台blade damper // clapper // mid-span 叶身blade body叶型公差airfoil tolerance叶型理论airfoil theory叶型剖面airfoil section中弧线airfoil mean line工装Tooling标准件master piece // standard part // tool master 标准块master block // reference block测具gauge // measuring fixture // measuring tool 测头feeler // gauge head measuring head // stylus 车床夹具lathe fixture车刀lathe tool// cutter// turning tool吊具lifting tool夹具fixture饺孔夹具reaming fixture // reaming jig孔位置度测具hole true position gauge拉刀broach (Bro.) // broaching cutter拉削夹具broaching fixture刨削夹具planner fixture钳工工具bench-work tool丝套insert // thread insert丝锥taper // (screwing）tap镗刀boring cutter镗杆boring bar (B/bar) // boring spindle镗孔夹具boring fixture // boring jig铣槽工具grooving tool铣床夹具milling jig铣床铣槽刀milling machine // miller铣铣槽刀刀milling cutter // milling tool铣削夹具milling fixture钻铰刀drill reamer钻铰复合刀具combined drill and reamer钻具jig钻孔铰孔夹具drilling and tapping fixture钻孔样板drill template （DRT）// drillingtemplate钻模(drill) jig钻模板drill plate （DRP）钻模与夹具jigs and fixtures钻套jig bush钻套jig bush(ing)钻头bit // drill // drilling bit机械加工术语Terms for Machining半精加工semi-finishing // semifinishingmachining插slotting车turning车床lathe// turning machine车床研磨lathe lapping车端面facing车螺纹thread turning车螺纹/螺纹加工thread/threading车削turning车削螺纹cut thread成形法forming冲头blanking ram // piercer // punch // ram head //slider冲压(punch) pressing冲压加工stamping冲压件pressing //stamping穿孔/套孔trepan/trepanning粗加工roughing machining锉file倒角deburr // chamfer倒角/去毛刺deburr(ing)倒棱chamfer电解抛光electrochemical polishing // electrolyticpolishing // electro-polishing电解蚀刻与抛光electrolytic etching andpolishing调整法machining on preset machine tool定位locating // location对刀to size // tool setting仿形法copying夹紧clamping饺reaming饺孔reaming饺孔机reaming machine饺孔钻reamer drill饺铆钉孔ream a rivet hole284精加工finishing // finish machining锯sawing锯背back of the saw锯槽kerf锯齿serration锯齿铣sawtooth milling拉削broaching冷装shrinkage fitting铆rivet(ing)铆钉rivet磨床grind // grinding machine磨端面face grinding磨料abraser // abrasive material // grinding compound磨削加工abrasive machining抛polish抛光buffing // burning // polish (Pol.)刨planing// shapering刨槽fillister // slot shaping刨齿gear shaper cutting // gear-shaping刨床planer // planing machine// shaper刨削shaping去毛刺deburring // fin cutting镗boring镗车两用机床boring lathe镗床borer // boring machine镗孔boring // borizing （金刚石）镗磨联合机床combined boring and honing machine镗钻两用机床boring and drilling machine铣mill // milling铣槽slot milling铣镗床milling-borer // milling and boring machine铣钻联合机床combined drill and mill machine铣钻两用机床milling and drilling machine旋spin旋锻spin forging // rotary forging // rotary swaging旋锻机spin forging machine // rotary forging machine // rotary swaging machine旋压spinning旋压成型stretch planishing // spin forming压装press fitting研lapping研齿gear lapping研磨lapping找正aligning // to center align装夹set-up装配assembly钻drill(ing)钻床drilling machine钻孔drilling钻埋头孔countersink表面处理（镀层、涂漆和金属喷镀）Surface treatment（Plating，Paining & Metal sparying）涂层不良imperfectly coated spots涂层过厚thickening涂层凸起lifting of the coating, protrusion, orlifting冲压Punch尺寸检验dimension inspecting基准datum技术条件technical condition加工fabricate夹clamping夹紧面clamping surface夹具fixture钻孔drill钻头drill图纸及工艺规程常用词汇EverydayVocabularies on Working Drawings &W.P.S尺scale尺寸dimension // size尺寸单向极限single of size尺寸过大oversize尺寸过小undersize尺寸极限limit of size尺寸最大极限maximum of size尺寸最大余量极限maximum metal of size尺寸最小极限minimum of size齿根root处理treatment吹砂blast // abrasive blasting垂直度perpendicularity // squareness垂直度公差squareness tolerance单位燃油消耗量specific fuel consumption单位压力unit pressure单位装配件assembly unit单向公差unilateral tolerance单向公差域bilateral tolerance zone氮化nitriding当量equivalent挡块stop285刀柄holder刀杆cutter bar刀痕scar // tool mark等离子喷镀plasma spray等值equivalent低压压气机LP compressor地面试车ground run典型加工typical operation防锈rust protection // rust proof仿形copy仿形铣床copying milling machine // duplicator 仿型加工form machine高速钢high speed steel高速工具钢high speed tool steel高温合金high temperature alloy高压压气机HP compressor根root根切undercut公差tolerance公差带tolerance band公称尺寸nominal size功能function功能尺寸function dimension功能要求functional requirement构造尺寸constructional dimension固定fasten固定工具fastening tool故障defect // blemish // failure // fault // imperfection // trouble故障分析trouble shooting关键零件critical part观点view过盈interference过盈配合interference fit过载overload互换性interchangeability互换性组件interchangeable assembly花键splined shaft花键轴splined shaft火裂fire cracks机床machine (tool)机匣case // casing基本尺寸base dimension // basic size基本公差basic tolerance基本数basic member基本锥体basic taper基孔制hole basis limit system基线basic line基轴制shaft basis基轴制shaft basis limit system基准data // reference基准尺寸datum dimension基准点datum point基准件basic member基准角basic angle基准面datum face // datum plane基准线datum line // zero line基准叶片master vane几何公差geometrical tolerance几何精度accuracy geometrical加工制造fabricate夹紧fastening夹具clamping apparatus // dogging tool // fixture// holding device // jig检验装置checker节径pitch diameter精度accuracy // precision精锻precision forging精加工finishing精磨precision ground精确长度exact length精调fine adjustment // accurate adjustment//precision adjustment孔bore // hole框flame拉床broacher // broaching machine拉刀broacher拉销broach离心式压气机centrifugal compressor离心铸造centrispum casting iron立式车床vertical lathe立式钻床upright drill螺母nut螺栓bolt名义尺寸base size // nominal size内径inner diameter内裂internal crack内外函发动机by-pass engine内应力internal stress内圆磨床internal grinding machine耐磨性resistance to wear耐热钢heat resisting steel耐热合金heat-resisting啮合mesh啮合线action line扭转twisting排气边trailing edge排气喷口exhaust nozzle盘disc抛光polishing抛光机polisher // burnishing wheel刨平plane泡疤blister配合fit // matching // mating286配合等级classes of fit // grade of fit配合间隙class of fit配合类型types of fit配合容差fitting allowance配合直径snap diameter配合制system of fits配件mating piece喷口nozzle喷丸peening // shot-blasting喷丸处理shot peening喷雾器atomizer喷嘴nozzle批生产mass production疲劳断裂fatigue fracture匹配matching片sheet偏心的eccentric偏心距eccentric distance偏心轮eccentric偏心套eccentric bushing偏心轴eccentric axis偏心装置eccentric偏移deviation漆paint切断parting切面cutting切切削深度depth of cut切头cropping切削cut切削工具cutter切削加工machining轻合金light alloy轻微的slight清楚的clear清理cleaning清漆层不好poorly varnished film区域zone曲度curve曲面curved surface曲线curve屈服yield屈服点yield point屈服强度yield strength屈服应力proof stress // yield stress缺口敏感性notch sensitivity缺陷blemish // defect // failure // fault // imperfection热脆性red shortness热裂hot crack热裂纹clink热损heat waste容差allowance熔化smelt (ing)蠕变creep设计design设计草图rough plan设计尺寸design size设计角design angle伸长elongation伸长率elongation失速stall（飞机）湿吹砂vapour blast时间表schedule时效ag(e)ing时效处理seasoning识别号identification number实际尺寸actual size实际有效直径virtual effective diameter式样form // manner事故accident // failure视图view试车test run // trial run试件test piece试验examine // test试验参数test data试样coupon // (test) sample // test specimen试样长度sample释放release手册manual手段means寿命limit of life数number数据data数量quantity说明书description // specification榫头root调正adjustment调质improvement跳动量runout凸起overfill凸台boss凸缘collar // flange图scheme图板drawing board图号drawing number图形机体feature图样draft // drawing图纸drawing (sheet)图纸比例drawing scale图纸技术要求drawing call-out涂层不良imperfectly coated spots涂层过厚thickening涂层凸起lifting of the coating, protrusion, or lifting287涂漆paint推荐尺寸preferred size推力thrust推力比thrust ratio椭圆度ovality外部检查visual inspection外函道by-pass duct外螺纹external screw thread外形outline外圆磨床circular grinding machine位置location位置公差positional tolerance蜗杆worm蜗轮work wheel卧式钻镗床horizontal boring & drilling machine 误差error习惯表示法conventional representation铣床milling machine铣刀milling现场site // spot相当的equivalent相应值equivalent消除应力stress relieved // stress released消耗consumption销钉pin销孔bore // pin hole销子pin斜度angularity (tolerance)压板clamp (plate)氩弧焊argon-arc welding应变strain应变时效strain ageing应力stress应力腐蚀裂纹stress corrosion crack应力消除stress relieving应力-应变曲线stress strain curve应力-应变图stress strain diagram圆度circularity // roundness圆滑smoothness圆心center of circle圆柱度cylindricity直径diameter制度system制造manufacture质量quality质量验收标准quality acceptance standard中心距center distance中心孔center hole轴shaft轴承bearing轴线axis轴线axis主喷咀main nozzle铸造casting铸造组织casting iron structure专门技术know-how专门铣床planomilling machine专用工具special tool专用工装special tooling专用设备special purpose machine专用铣床production machine转换reset转子叶片blade装备device装夹mount装配assembly // mount装配车间assembling shop // assembly shop //erecting shop // fitting shop装配间隙fit clearance装配件assembly装配图assembly drawing // erection drawing装箱退火close annealing装置device锥齿轮bevel gear锥度taper锥螺纹taper thread锥面conical surface锥体slow object // taper总尺寸外形尺寸overall dimension总体布置图general layout总装车间assembly department总装件assembly // general assembly总装图general layout组合件joint组件assembly组装件sub assembly钻drill钻床drill machine钻具jig钻孔drill钻套drill jig bush钻头号drill number最大长度max length最大间隙major clearance最大推力full thrust // top thrust最大直径major diameter最小长度min length最小间隙minor clearance最小直径minor diameter缺陷解释Interpretation of Defects凹陷undercutting （在母材上沿焊接边的沟槽或288充填不足）变形deformation （在加工时未能保持住形状不变或与相邻部有不顺滑转接）电解腐蚀electrolytic action（不同金属间的电蚀作用造成的缺陷）断裂fracture（受力过大造成的破坏）开裂flaw外贸常用词语和术语Everyday Vocabularies of Foreign Trade询盘Inquiry把某物交付给某人to deliver sth to sb把询价记录在卷to keep the inquiry on file办理交货to effect delivery // to make delivery还盘Counter Offer还盘counter offer享有盛誉enjoy great popularity与某人达成交易conclude business with sb.达成交易close business // close a deal // close atransaction // close a bargain价格Price成本加保险费运费价cost, insurance & freight(C.I.F.)成本加运费价cost & freight (CFR)船上交货free on board (F.O.B)底价floor price货币currency价格偏低on the low side价格条件price terms廉价出售 a bargain sale市场价market price讨价还价bargain为某事拼命讨价还价drive a hard bargain oversth.与某人成交make a bargain with sb最低价rock-bottom price289290。

航空发动机常用汉英词汇

汉英分类词汇航空发动机类型Aero-E ngine Models超高涵比发动机ultra high bypass engine超音速冲压喷气发动机scramjet engine冲压喷气发动机ram-jet engine带推力转向系统的发动机engine with thrust deflector system带自由涡轮双轴涡轮轴喷气发动机twi n-spool turbo-shaft with free-power turbi ne单轴涡轮喷气发动机sin gle-spoolturbo-jet engine低涵比发动机low bypass turbofa n 反向旋转发动机con tra-rotati on engine高涵比发动机high bypass turbofa n 后风扇涡轮喷气发动机aft fan turbo-jet engine活塞式发动机pist on (-a nd-cyli nder) engine // pist on-drive n engine桨扇发动机prop-fa n engine离心涡轮喷气发动机ce ntrifugal turbo-jet engine脉冲喷气发动机pulse jet engine前风扇涡轮喷气发动机front fan turbo-jet engine燃气轮机gas turb ine engine三轴桨扇发动机three-shaft prop-fa n engine三轴涡轮前风扇涡轮发动机triple-spool front fan turbo-jet双轴外涵涡轮喷气发动机twi n-spool by-pass turbo-jet双轴涡轮风扇发动机twi n-spool turbo-fan engine同向旋转发动机co-rotatio n engine 夕卜骨架发动机exo-skeletal engine涡轮冲压喷气发动机turbo/ram jet engine涡轮风扇发动机turbofa n engine涡轮火箭发动机turbo-rocket engine 涡轮螺旋桨发动机turboprop en gi ne 涡轮喷气发动机turbojet engine涡轮轴发动机turbo-shaft engine轴流涡轮喷气发动机axial flow turbo-jet engine型面profile型面座标图aerofoil ordin ate chart 型式form轴流式压气机axial (flow) compressor函道duct函道比by-pass函道风扇ducted-fa n中介机匣in termediate case燕尾形样dovetail root叶片vane (—般指静子叶片)压气机compressor压气机机匣compressor case效率efficie ncy 压气机盘compressor disc压缩比compressi on ratio 牙底root 涡轮导向器turbi ne no zzle涡轮盘turb ine disc 燃烧室bur ner // combustio n chamber //combustor燃烧室外套combusti on outer case燃油导管discharge no zzle燃油滤fuel filter燃油喷咀fuel atomizer // fuel spray no zzle 燃油消耗量fuel con sumpti on火焰筒liner扩散器机匣diffuse case 加力燃烧室afterburner航空发动机叶片术语Terms of Aero-E ngine Airfoils叶片类型Type of Airfoils动叶blade // bucket静叶vane空心叶片hollow blade // core blade实心叶片solid blade涡轮导向器turbi ne no zzles涡轮导向器扇形段turbi ne no zzle segme nt 涡轮导向器叶片turbi ne no zzle vane // no zzle guide vane (n gv)涡轮工作叶片turbi ne blade // bucket涡轮静子叶片turbi ne no zzle vane // no zzle guide vane (n gv) 涡轮叶轮turbi ne wheel 涡轮叶片turb ine blades & vanes // buckets 涡轮转子叶片turbi ne blade // bucket压气机定子叶片compressor vane // vane压气机工作叶片compressor blade // blade 压气机叶轮compressor impeller //compressor wheel压气机叶片compressor blades & vanes压气机整流叶片compressor vane // vane压气机转子叶片compressor blade // blade叶片的结构特点Characteristics of Airfoil Structure 基体部分base榫头tip // cog // fir-tree // root // tenon 叶根blade root // root // vane tang 叶冠shroud // tip platform // tip shroud 叶身blade body 叶型部分aerofoil // profile缘板platform // shroud叶片的主要名称Key Terms of Airfoil Body基体base 进气边/前缘leadi ng edge 理论叶型theoretical developedairfoil/profile 排气边/ 后缘traili ng edge // exhaust edge 弦chord 型线airfoil curve 叶背blade back // con vex side // blade convex叶盆blade bas in // vane bas in // blade/va ne concave叶片阻尼台blade damper // clapper // mid-spa n叶身blade body叶型公差airfoil tolera nee叶型理论airfoil theory叶型剖面airfoil secti on中弧线airfoil mean line工装Tooli ng标准件master piece // sta ndard part // tool master标准块master block // refere nee block 测具gauge // measuri ng fixture //measuri ng tool测头feeler // gauge head measuri ng head // stylus车床夹具lathe fixture车刀lathe tool// cutter// turni ng tool 吊具lifti ng tool夹具fixture饺孔夹具reaming fixture // reaming jig孑L位置度测具h ole true positi on gauge拉刀broach (Bro.) // broach ing cutter 拉削夹具broachi ng fixture刨削夹具pla nner fixture钳工工具ben ch-work tool 丝套in sert // thread in sert丝锥taper // (screwing) tap镗刀bori ng cutter 镗杆bori ng bar (B/bar) // bori ng spin dle 镗孔夹具bori ng fixture // bori ng jig铣槽工具grooving tool铣床夹具milli ng jig铣床铣槽刀milli ng machi ne // miller 铣铣槽刀刀milli ng cutter // milli ng tool铣削夹具milli ng fixture钻铰刀drill reamer 钻铰复合刀具comb ined drill and reamer钻具jig 钻孔铰孔夹具drilli ng and tapp ing fixture 钻孔样板drill template (DRT) // drillingtemplate钻模(drill) jig钻模板drill plate (DRP) 钻模与夹具jigs and fixtures 钻套jig bush 钻套jig bush( ing)¥ 占头b it // drill // drilli ng bit机械加工术语Terms for Machi ning半精加工semi-fi ni shi ng // semifi ni shi ng machi ning插slotti ng 车turni ng 车床lathe// turni ng machi ne 车床研磨lathe lapp ing车端面facing车螺纹thread tur ning车螺纹/螺纹加工thread/threadi ng车肖U turni ng车削螺纹cut thread成形法formi ng冲头bla nking ram // piercer // punch // ram head // slider冲压(pun ch) press ing冲压加工stampi ng冲压件press ing //stamp ing 穿孑L / 套孑L trepa n/trepa nning 粗加工rough ing machi ning锉file 倒角deburr // chamfer 倒角/去毛刺deburr(i ng)倒棱chamfer 电解抛光electrochemical polishi ng //electrolytic polish ing // electro-polishi ng 电解蚀刻与抛光electrolytic etchi ng and polish ing调整法machi ning on preset mach ine tool 定位locat ing // locati on对刀to size // tool sett ing仿形法copy ing夹紧clampi ng饺reami ng饺孑L reaming饺孔机reaming machi ne饺孔钻reamer drill饺铆钉孑L r eam a rivet hole精加工fin ishi ng // fin ish machi ning锯saw ing锯背back of the saw锯槽kerf锯齿serrati on锯齿铣sawtooth milli ng拉肖U broachi ng 冷装shri nkage fitt ing 铆rivet(i ng) 铆钉rivet磨床grind // grinding machi ne磨端面face grinding磨料abraser // abrasive material // grinding compo und磨削加工abrasive machi ning抛polish抛光buffi ng // burni ng // polish (Pol.)刨pla ning// shaperi ng刨槽fillister // slot shap ing刨齿gear shaper cutt ing // gear-shap ing 刨床pla ner // pla ning mach ine// shaper 刨肖U shap ing去毛刺deburri ng // fin cutt ing镗bori ng镗车两用机床bori ng lathe镗床borer // bori ng mach ine镗孑L bori ng // boriz ing (金冈H石)镗磨联合机床comb ined bori ng and honing mach ine镗钻两用机床bori ng and drilli ng mach ine 铣mill // milli ng铣槽slot milli ng铣镗床milli ng-borer // milli ng and bori ng mach ine铣钻联合机床comb ined drill and mill mach ine铣钻两用机床milli ng and drilli ng mach ine 旋spi n旋锻spi n forgi ng // rotary forgi ng // rotaryswagi ng旋锻机spi n forgi ng mach ine // rotary forgi ng mach ine // rotary swagi ng mach ine 旋压spinning旋压成型stretch pla nishi ng // spi n formi ng 压装press fitt ing研lapp ing研齿gear lapp ing研磨lapp ing找正alig ning // to cen ter alig n装夹set-up装酉己assembly钻drill(i ng)钻床drilli ng mach ine钻孔drilli ng钻埋头孑L coun ters ink表面处理(镀层、涂漆和金属喷镀)Surface treatme nt(Plating , Paining & Metal sparying )涂层不良imperfectly coated spots涂层过厚thicke ning涂层凸起lifti ng of the coat ing, protrusi on, or lifting冲压Punch尺寸检验dime nsion in spect ing基准datum技术条件tech ni cal con diti on力卩工fabricate 夹clampi ng 夹紧面clampi ng surface 夹具fixture 钻孔drill 钻头drill 图纸及工艺规程常用词汇EverydayVocabularies on Worki ng Draw ings &W.P.S尺scale 尺寸dime nsion // size 尺寸单向极限si ngle of size尺寸过大oversize尺寸过小un dersize尺寸极限limit of size尺寸最大极限maximum of size尺寸最大余量极限maximum metal of size 尺寸最小极限mi nimum of size齿根root 处理treatme nt吹砂blast // abrasive blasti ng 垂直度perpe ndicularity // square ness垂直度公差square ness tolera nee单位燃油消耗量specific fuel con sumpti on 单位压力unit pressure单位装配件assembly unit单向公差un ilateral tolera nee 单向公差域bilateral tolera nee zone氮化n itrid ing 当量equivale nt 挡块stop 刀柄holder 刀杆cutter bar 刀痕scar // tool mark 等离子喷镀plasma spray等值equivale nt低压压气机LP compressor地面试车ground run典型加工typical operatio n防锈rust protect ion // rust proof 仿形copy仿形铣床copy ing milli ng mach ine // duplicator仿型加工form machi ne高速钢high speed steel 高速工具钢high speed tool steel高温合金high temperature alloy高压压气机HP compressor根root 根切un dercut 公差tolera nee 公差带tolera nee band公称尺寸nominal size功能fun cti on 功能尺寸function dime nsion 功能要求functional requireme nt构造尺寸eon structi onal dime nsion固定faste n 固定工具faste ning tool故障defect // blemish // failure // fault // imperfectio n // trouble 故障分析trouble shoot ing 关键零件critical part观点view 过盈in terfere nee 过盈配合i n terfere nee fit过载overload 互换性in tercha ngeability互换性组件in tercha ngeable assembly花键spli ned shaft 花键轴spli ned shaft火裂fire cracks 机床machi ne (tool) 机匣case // cas ing基本尺寸base dimension // basic size基本公差basic tolera nee基本数basic member 基本锥体basic taper 基孔希9 h ole basis limit system基线basic line 基轴制shaft basis 基轴制shaft basis limit system 基准data // refere nee 基准尺寸datum dime nsion基准点datum point基准件basic member 基准角basic an gle 基准面datum face // datum pla ne 基准线datum line // zero line 基准叶片master vane 几何公差geometrical tolera nee几何精度accuracy geometrical力卩工制造f abricate夹紧faste ning 夹具clampi ng apparatus // dogg ing tool // fixture // holdi ng device // jig 检验装置checker节径pitch diameter 精度accuracy // precisi on 精锻precisi on forgi ng 精加工fini shi ng 精磨precisi on ground 精确长度exact len gth精调fine adjustme nt // accurate adjustme nt //precisi on adjustme nt孑L bore // hole框flame拉床broacher // broach ing mach ine 拉刀broacher 拉销broach离心式压气机cen trifugal compressor离心铸造cen trispum casti ng iron立式车床vertical lathe立式钻床upright drill螺母nut 螺栓bolt名义尺寸base size // nominal size内径inner diameter 内裂in ternal crack内外函发动机by-pass engine内应力in ternal stress 内圆磨床in ternal grinding machi ne耐磨性resista nee to wear耐热钢heat resisti ng steel耐热合金heat-resist ing啮合mesh 啮合线acti on line扭转twisti ng 排气边traili ng edge排气喷口exhaust no zzle盘disc抛光polish ing 抛光机polisher // bur nishing wheel 刨平pla ne 泡疤blister配合fit // match ing // mat ing 配己合等级classes of fit // grade of fit配合间隙class of fit配合类型types of fit配合容差fitti ng allowa nee配合直径snap diameter酉己合制system of fits配件mati ng piece 喷口no zzle喷丸pee ning // shot-blasti ng喷丸处理shot pee ning喷雾器atomizer 喷嘴nozzle 批生产mass producti on 疲劳断裂fatigue fracture匹配matchi ng片sheet 偏心的ecce ntric偏心距ecce ntric dista nee 偏心轮ecce ntric 偏心套ecce ntric bush ing 偏心轴ecce ntric axis 偏心装置ecce ntric偏移deviati on漆pai nt 切断part ing切面cutt ing切切削深度depth of cut 切头cropp ing切削cut 切削工具c utter切削加工machi ning轻合金light alloy 轻微的slight 清楚的clear 清理clea ning 清漆层不好poorly varni shed film区域zone 曲度curve 曲面curved surface 曲线curve屈服yield 屈服点yield point 屈服强度yield stre ngth屈服应力proof stress // yield stress缺口敏感性n otch sen sitivity缺陷blemish // defect // failure // fault // imperfectio n热脆性red short ness 热裂hot crack 热裂纹cli nk 热损heat waste 容差allowa nee 熔化smelt (ing) 蠕变creep 设计desig n 设计草图rough pla n设计尺寸desig n size设计角desig n an gle伸长elon gati on 伸长率elon gati on失速stall (飞机) 湿吹砂vapour blast 时间表schedule 时效ag(e)i ng 时效处理seas oning 识别号ide ntificati on nu mber 实际尺寸actual size实际有效直径virtual effective diameter 式样form // manner 事故accide nt // failure 视图view 试车test run // trial run 试件test piece 试验exam ine // test 试验参数test data试样coup on // (test) sample // test specime n 试样长度sample释放release 手册manual 手段means 寿命limit of life 数nu mber 数据data 数量qua ntity 说明书descripti on // specificati on榫头root 调正adjustme nt 调质improveme nt跳动量runout 凸起overfill 凸台boss 凸缘collar // flange 图scheme 图板draw ing board 图号draw ing nu mber 图形机体feature 图样draft // draw ing 图纸draw ing (sheet) 图纸比例draw ing scale图纸技术要求drawi ng call-out 涂层不良imperfectly coated spots 涂层过厚thicke ning 涂层凸起lifti ng of the coat ing, protrusi on, or lifting 涂漆p ai nt推荐尺寸preferred size推力thrust 推力比thrust ratio 椭圆度ovality 夕卜部检查v isual in specti on夕卜函道b y-pass duct夕卜螺纹e xter nal screw thread外形outl ine夕卜圆磨床circular grinding mach ine 位置locati on位置公差positi onal tolera nee蜗杆worm 蜗轮work wheel 卧式钻镗床horiz on tal bori ng & drilli ng mach ine 误差error习惯表示法conven ti onal represe ntati on 铣床milli ng mach ine 铣刀milli ng 现场site // spot 相当的equivale nt相应值equivale nt消除应力stress relieved // stress released 消耗con sumpti on 销钉pin 销孑L bore // pin hole销子pin斜度an gularity （tolera nee）压板elamp （plate）氩弧焊argon-are weldi ng应变strain 应变时效strain age ing应力stress 应力腐蚀裂纹stress eorrosi on eraek应力消除stress relievi ng应力-应变曲线stress strain curve应力-应变图stress strain diagram圆度circularity // roundn ess 圆滑smooth ness 圆心een ter of circle 圆柱度eyli ndricity 直径diameter 希9度system 希9造manu faeture 质量quality 质量验收标准quality aeeepta nee sta ndard中心距een ter dista nee中心孑L e en ter hole轴shaft 轴承beari ng 轴线axis 轴线axis 主喷咀mai n no zzle铸造east ing 铸造组织east ing iron structure 专门技术kno w-how专门铣床pla no milli ng maeh ine专用工具special tool专用工装special tooli ng专用设备special purpose maeh ine专用铣床product ion maeh ine转换reset 转子叶片blade装备device 装夹mount装酉己assembly // mount装配车间assembli ng shop // assembly shop // erect ing shop // fitti ng shop装配间隙fit eleara nee装配件assembly 装配图assembly draw ing // erectiondraw ing装箱退火close ann eali ng装置device 锥齿轮bevel gear 锥度taper 锥螺纹tap er thread 锥面coni cal surface 锥体slow object // taper 总尺寸外形尺寸overall dime nsion总体布置图gen eral layout总装车间assembly departme nt总装件assembly // general assembly 总装图gen eral layout 组合件joi nt 组件assembly 组装件sub assembly 钻drill 钻床drill maeh ine 钻具jig 钻孔drill 钻套drill jig bush 钻头号drill nu mber 最大长度max len gth最大间隙major eleara nee最大推力full thrust // top thrust最大直径major diameter最小长度min len gth最小间隙minor eleara nee最小直径minor diameter缺陷解释In terpretati on of Defects凹陷un dereutti ng （在母材上沿焊接边的沟槽或充填不足）变形deformation （在加工时未能保持住形状不变或与相邻部有不顺滑转接）电解腐蚀electrolytic action （不同金属间的电蚀作用造成的缺陷）断裂fracture （受力过大造成的破坏）开裂flaw外贸常用词语和术语Everyday Vocabularies of Foreig n Trade询盘In quiry把某物交付给某人to deliver sth to sb把询价记录在卷to keep the in quiry on file 办理交货to effect delivery // to make delivery还盘Cou nter Offer还盘coun ter offer享有盛誉enjoy great popularity与某人达成交易con elude bus in ess with sb.达成交易close bus in ess // close a deal // close a tran sacti on // close a barga in价格Price成本加保险费运费价cost, i nsura nee & freight (C.I.F.)成本加运费价cost & freight (CFR)船上交货free on board (F.O.B)底价floor price货币curre ncy价格偏低on the low side价格条件price terms廉价出售 a barga in sale市场价market price讨价还价bargain为某事拼命讨价还价drive a hard bargain over sth.与某人成交make a barga in with sb最低价rock-bottom price。

发动机专业英语单词

Para 1 基本原理Notes:Para.1.appreciate: understand fully，评价，估价，理解unsuitability :不适合，不相称，不匹配present:submit,offer,give，提出，设置2.patent: n,专利v,取得…专利athodyd: 航空热力管道，冲压式喷气发动机ram jet: 冲压喷气发动机3.turbo-jet engine:涡轮喷气发动机turbo-propeller engine: 涡轮螺桨发动机viscount aircraft: 子爵式飞机twin-spool: 双转子triple-spool: 三转子by-pass: 双涵式，内外涵ducted fan: 管道风扇式,涵道风扇式4.piston engine: 活塞发动机solely:单独地,独自地,只是5.pulse jet: 脉动式发动机turbo/ram jet: 涡轮/冲压喷气发动机6.momentum: 动量issue:流出,放出impart…to…:give，给予jet: 喷嘴8.sprinkler: 喷水器by virtue of: 凭借，利用firefighting: 消防hose: 软管carnival: 狂欢节9.resultant: 合成的，总的10.convert…into…:change…into，11.convergent: 收敛的divergent: 发散的target vehicle: 耙机12.intermittent: 间歇的，周期性的static：静止的，静态的dynamic：动力的，动态的aero-：空气的aerodynamic：空气动力学的robust：坚固的，强壮的spring-looded：绷有弹簧的(图1-7)：shutter valve：薄片式，快门式阀门，节气活门depression：下降rotor：旋翼helicopter：直升机dispense with：免去，不用resonate：共振，谐振13.decompose：分解14.inherent：内在的，固有的up to：直至，高达（上限）15.somewhat：比较，有点blade：叶片16.blade-tip：翼尖departure from:偏离，违背17.offset：补偿，弥补，冲淡18.Mach number：马赫数19.variable intake：可调进气道afterburner：加力燃烧室shut down：停车，关闭guide vane：导向叶片divert：redirectsustained：stable，稳定的，持续的cruise condition：巡航状态20.alternative：另一种结构型式21.kerosine：煤油multi-stage：多级in the order of ：数量级22.interceptor：截击机space-launcher：航天飞机high altitude：高空short duration：短的巡航时间Part 2工作循环和空气流动notes:para.:1.efflux：射流，流出，涌（迸）出2.stroke：冲程reciprocate：往复式的3.fabricated：板金焊接的（板料）4.remainder：剩余物5.assembly：组件7. embody：包含（contain）product：乘积extract：取出（功），吸收（功）9.trace through：追踪，指示10.attain：到达（achieve）11.adiabatic：绝热的friction：摩擦conduction：导热，热传导turbulence：湍流，扰动12.propelling nozzle：推进喷管deceleration：减速acceleration：加速13.convert(convertion)…to(into)…supersonic：超音速的transonic：跨音速的subsonic：压音速的encounter：遭遇，遇到14.failure：损坏，失效vibration：振动eddy：旋涡15.straight-through flow system：直流系统frontal area：迎风面积subsequent：后续的（following）17.conducive：有助（益）于，促进…的specific：单位的，比的（如specific heat，比热）specific fuel consumption：耗油率18.configuration：机构，构造，结构型式19.overboard：出去，向…外variation：变形Part 3 压气机Para.1.centrifugal：离心的axial：轴向的shaft：轴2.impeller：叶轮diffuser：扩压器3.with regard to：关于，对于，论及，提及4.specific thrust：单位推力5.casing：机匣plenum chamber：稳压腔6.radially：辐射地，径向地initially whirl：预旋8. tip speed：叶尖速度9.leakage：泄露clearance：间隙，公差10.ball bearing：滚珠轴承roller bearing：滚棒（柱）轴承ease of detachment：易于拆卸11.forged disc：铸造盘，铸件sweep back：回弯12.all-round efficiency：圆周效率surge：喘振ram effect：冲压效应13.tangential：切向的aerodynamic buffeting impulses：气动抖振14.aerofoil：气动翼型angular setting of the vanes：叶片安装角inlet guide vanes：进口导流片15.air annulus area：空气环形流道面积tapering：作成锥形17. operating flexibility：最佳速度20.correct the deflection：工作适应性air straightener：空气整流器21.air breakaway：气流分离blade stall：叶片失速22.tortuous：曲折的，扭曲的culminate：vi，达到顶点，以…告终25.alignment：准直，对中26.drum-type：鼓筒式disc-dype：盘式spline：花键，用花键连接spacer rings：垫圈blade platform：叶片榫缘27. rock：摇动，摇摆28. angle of incidence：倾角，迎角29.retaining rings ：定位环，固定环，保持环in packs：成组，成批shroud：叶冠，加叶冠32.blade profile：叶片型面flight manoeuvre：飞行机动，飞行动作ingestion：吸入外物34. off design speed：非设计转速35.cough：咳嗽a bang of varying severity：忽强忽弱的放炮声36.safety margin：安全裕度37.bleeding：放气，以…抽气减压38.pneum(o)-：[词头]空气，气动，呼吸pneumonia：肺炎pneumatic：气动的choking：阻塞39.actuator：作动筒，促动筒r.p.m.= revolution per minute40.fatigue resistance：耐疲劳42. titanium：钛carbon or glass fiber composite：碳或玻璃纤维复合材料43.magnesium：镁44.engines designed entirely for lift：升力发动机45.balancing：平衡in view of：由于，鉴于，考虑到Part 4 燃烧室Para.mercial aircraft traffic：民用航空exhaust smoke：排气烟带4.normal：额定的blow away：吹熄5.flame tube：火焰筒liner：套筒（管）meter：量度，测量，定量multi-meter：万用表-meter：仪表，仪器6.snout：主进气口，飞机头部swirl vane：扰流器（叶片）perforated flare：多孔漏斗recirculation：回流air casing：燃烧室外套7.toroidal vortex：环形涡流anchor：驻定，抛锚hasten: 加速，促进8.break up：破碎，弄细9.nozzle guide vanes of the turbine：涡轮导向器叶片dilution：稀释10.igniter plug：电嘴点火器self-sustained：自行保持的13.atomizer jets：雾化喷嘴vaporizing principle：汽化原理，蒸发原理baffle plate：隔板14.multiple chamber：多个单管燃烧室tubo-annular chamber：环管燃烧室annular chamber：环型燃烧室17. interconnector：联焰管18.overhaul：大（翻）修compactness：结构紧凑21.decrease by：减小了decrease to：减小到22.air spray type burner：气动喷嘴aerate：充（通）气，吹气over-rich pockets of fuel vapour：过富的燃油蒸气，油兜，油井（穴），油带24. flame extinctior：熄火25.incur：招致，遭受（损失，坏结果）30.glide：滑翔dive：俯冲idling：慢车rich limit：富油极限weak limit：贫油极限mixture strength：混合物浓度31.loop：包线33. negligible：可忽略的35.creep failure：蠕变stress：应力strain：应变Part 5 涡轮Para.2.torque：力矩stationary：静止的，固定的moving：运动的with the advent of：随着…到来，出现3.shaft-power engine：涡（轮）轴发动机free-power turbine：动力涡轮reduction gear：减速齿轮（器）interpose：介入，插入promise：妥协，协调，调和power/weight ratio：功重比patible with：与…相适应的，相容的juxtaposition：排列位置pure impulse turbine：纯冲击式涡轮pure reaction turbine：纯反作用式涡轮incorporated：合并，加入，包含，包括，采用cartridge and air starters：火药式和空气式起动机7. discharge：流出8. detrimental：有害的exhaust cone supports and struts：排气锥支座与支板9.stagger angle：叶片扭转角-安装角10.degree of reaction：反力度12. self-aligning coupling：自调联轴器15.machined forging：机加铸件flange：安装边，法兰盘perimeter：周长18.permitted stress：许用应力trailing edge：后缘leading edge：前缘crack：裂纹19.has an important bearing on：对…有重要影响，关系limiting rim speed：极限轮缘速度de laval bulb root fixing：特拉瓦球形叶根固定（法）be superseded by：以…代替（取代）…‘fir-tree’ fixing：枞树形固定（法），枞树形榫齿serration：榫齿，锯齿stiffen：拉紧，加强hollow：空心的20.segment：扇形段peripheral：圆周的，周边的peri-：圆周的，周边的22. flow characteristics：流量特性back pressure：反压，背压24. creep life：蠕变寿命creep characteristics：蠕变特性26.bending loads：弯曲载荷thermal shock：热冲击high frequency fluctuations：高频振荡28. foregoing = above, preceding29ferritic：铁素体的，三价铁的ferro-：亚铁的austenitic：奥氏体的nickel：镍Part 6 排气系统Para.2. impact n碰撞, 冲击, 冲突, 影响, 效果give an impact to 对....起冲击作用make/have a strong/great/full impact on 对....有巨大影响This accident made a full impact on his life.match n. 火柴, 比赛, 竞赛, (足球, 捧球, 蓝球)比赛, 匹配v. 相配, 相称, 比赛, 相比, 匹配The curtains do not match with the decoration.窗帘与室内装璜不相配。

发动机英语

汽车发动机中英文对照R-直列多缸排列发动机V-V型汽缸排列发动机B-水平对置式排列多缸发动机WA-汪克尔转子发动机W-W型汽缸排列发动机Fi-前置发动机（纵向）Fq-前置发动机（横向）Mi-中置发动机（纵向）Mq-中置发动机（横向）Hi-后置发动机（纵向）Hq-后置发动机（横向）OHV-顶置气门，侧置凸轮轴OHC-顶置气门，上置凸轮轴DOHC-顶置气门，双上置凸轮轴CVTC-连续可变气门正时机构VVT-i--气门正时机构VVTL-i--气门正时机构ES-单点喷射汽油发动机EM-多点喷射汽油发动机SDi-自然吸气式超柴油发动机TDi-Turbo直喷式柴油发动机ED-缸内直喷式汽油发动机PD-泵喷嘴D-柴油发动机（共轨）DD-缸内直喷式柴油发动机TA-Turbo（涡轮增压）SFI-连续多点燃油喷射发动机FSI-直喷式汽油发动机气门Valve 顶置凸轮轴Over Head Camshaft（OHC）顶置双凸轮轴Double Over Head Camshaft（DOHC）或称Twin Camshaft 直列四缸Inline4 水平对置发动机(Boxer Engine)四冲程汽油机(Reciprocating 4Stroke Cycle Engine)柴油机(Diesel Engine)转子发动机(Rotary Engine)气缸体(Cylinder Block)气缸套(Cylinder Liner)连杆(Connecting Rod)曲轴(Crank Shaft)油底壳(Oil Pan)活塞(Piston)活塞销(Piston Pin)活塞环(Piston Ring平衡机构(Balancer)气缸盖(Cylinder Head)进气门和排气门(Intake Valve/Exhaust Valve)气门座(Valve Seat)气门弹簧(Valve Spring)气门锁块(Cotter)气门间隙调节垫片(Shim)凸轮轴(Camshaft)摇臂(Rocker Arm)摇杆(Swing Arm)齿形皮带(Timing Belt)气门间隙调节器(又称液压挺杆)(Valve Lash Adjuster)配气相位(气门开闭角度)(Valve Timing)可变进气系统(Variable Induction System)化油器(Carburetor) 喉管(Venturi)可变喉管(Variable Venturi)汽油泵(Fuel Pump)惯性增压(Inertia Change)进气管(Intake Manifold)节气门(Throttle Valve)空气滤清器(Air Cleaner)汽油喷射系统(Fuel Injection) 空气流量计(Air Flow Meter)节气门体(Throttle Body)汽油喷嘴(Injector)单点喷射(Single Point Injection) 自然进气(Natural Aspiration) 涡轮增压器(Turbo Charger) 中冷器(Inter Cooler)爆振(Knocking)爆振传感器(Knock Sensor) 机械增压器(Super Charger)。

(整理)发动机相关中英文对照

汽车发动机相关中英文对照发布日期:2008/06/02 信息来源:环球汽配资源汽车发动机相关中英文对照发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室` swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston)凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated piston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod 连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod big end连杆杆身connecting rod shank副连杆slave connecting rod叉形连杆fork-and-blade connecting rod 主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod 活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing 薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper 扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibration balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order二级往复贯性力reciprocating inertia force, 2nd order离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece camshaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle凸轮升程cam-lobe lift凸轮尖cam nose凸轮从动件cam follower齿轮传动机构gear drive正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve) 双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门side valve倾斜气门inclined overhead valve直立气门vertical overhead valve套筒式滑阀sleeve valve气门机构valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆valve stem加大气门杆oversize valve stem气门头valve head气门工作面valve face气门边限valve margin气门弹簧座valve-spring retainer气门锁片valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器valve rotator气门室valve cage气门油封valve oil seal气门口valve port气门座valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角valve seat angle气门座宽度valve seat width气门挺杆valve tappet(valve lifter)液力挺杆hydraulic tappet(lifter)无间隙挺杆zero-rush tappet (non-clearance tappet)筒形挺杆barrel type tappet油压挺杆ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位tappet rotation排气门挺杆exhaust valve lifter气门导管valve guide气门杆导管stem guide气门重叠度stem overlap气门开启持续时间valve duration气门正时标记valve timing sign气门弹簧valve spring气门内弹簧inner valve spring气门外弹簧outer valve spring刚性缓冲弹簧stiff buffer spring上紧弹簧energizing spring防振气门弹簧non-surging spring弹簧座圈spring retainer蝶形弹簧belleville spring滚柱roller气门室盖valve chamber cover摇臂rocker arm高升程摇臂high lift rocker arm摇臂轴rocker arm shaft推杆push-rod摇臂支架rocker arm bracket气门摇臂室罩valve rocker chamber cover导向轮guide wheel导杆slide bar导轨slide rail张紧轮tensioning wheel链条张紧调节装置assembly chain tension adjuster张紧带轮tensioning pulley传动带张紧装置belt tensioner同步驱动皮带synchronous belt同步驱动皮轮synchronous belt pulley供油系fuel system控制燃烧系统controlled combustion system反湿气装置antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管constant purge line碳罐净化管canister purge line供油量fuel delivery循环供油量fuel delivery per cycle额定供油量rated fuel delivery怠速供油量idling speed fuel delivery供油规律fuel supply rate curve油量调节装置fuel control unit供油提前角fuel supply advance angle进油计量inlet metering几何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载variable volume unloading收缩容积retraction volume燃油喷油装置fuel injection equipment燃油喷射泵fuel injection pump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵in-line fuel injection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵high flanged-mounted fuel injection pump侧向安装燃油喷射泵side-mounted fuel injection pump端部突缘安装式燃油喷射泵end flange-mounted fuel injection pump V形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injection pump蓄能式燃油喷射泵accumulator fuel injection pump往复式燃油喷射泵reciprocating fuel injection pump驱动轴式燃油喷射泵driveshaft fuel injection pump单缸式燃油喷射泵single cylinder fuel injection pump圆柱式燃油喷射泵cylindrical fuel injection pump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing针阀needle芯轴central spindle喷嘴壳体nozzle body针阀升程needle lift喷嘴盖形螺母nozzle cap nut喷油器壳体nozzle holder突缘安装喷油器壳体flanged-mounted injection nozzle holder 燃油喷射泵传动装置transmision of an injection pump喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice海拔控制器altitude control提前器飞锤flyweight喷孔长径比ratio of nozzle hole length nozzle diameter喷嘴液动力特性nozzle hydrokinetic characteristics动态相位dynamic phase喷孔面积nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压injection back pressure高压油管high pressure pipe平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程prestroke收缩行程retraction stroke燃油箱fuel tank油箱盖fuel tank油位表fuel level gauge注油控制装置fill control system汽油箱gasoline tank( petrol tank)汽油供给管gasoline feed pipe加油管filler tube放油螺塞drain plug吸油管suction pipe刚性燃油管rigid fuel pipe进油孔fuel feed hole供油管supply pipe通气管bleeding pipe通气管bleeding pipe泄油阀spill valve泄油孔口spill port进油阀inlet valve最大油量限制器maximum fuel stop滴油dribble燃油表fuel gauge输油泵feed pump燃油泵fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump 机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump齿轮式输油泵gear fuel supply pump电动燃油泵eletric fuel pump带真空泵的汽油泵vacuum pump with fuel pump起动加油器primer起动给油杆primer lever燃油泵上体fuel pump body燃油泵下体fuel pump base燃油泵盖bowl cover进油口接头fuel inlet neck出油口接头fuel discharge port输出阀delivery valve泵油元件pump element回油阀部件fuel return valve assembly化油器carburetor化油器系统carburetor circuit简单化油器elementary carburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器four-barrel carburetor上吸式化油器updaught carburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensating carburetor 化油器附加器adaptor carburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头carburetor adaptor阻风门choke valve阻风活塞choke piston阻风板choke plate自动阻风门automatic choke阻风门拉钮choke button电控自动阻风门electric-assisted choke阻风管choke tube喉管venturi双重或三重喉管double & triple venturi阻风门拉线choke cable化油器小喉管booster venturi浮子系float system浮子float环形浮子annular float同心式浮子concentric float浮子支销float hinge pin浮子针阀float needle valve阀针valve needle浮子油面float level浮子臂float arm侧置浮子室式side float type怠速阀idle valve怠速针阀idle needle省油器economizer省油器阀economizer valve辅助空气阀auxiliary air-valve加速油井accelerating well加速泵accelerating pump加速泵喷嘴accelerating pump nozzle油门throttle手油门hand throttle节气门操纵手柄throttle control lever真空加浓器vacuum booster加浓器excess fuel device量孔体jet block怠速量孔idle metering jet主量孔main metering jet剂量阀活塞dosage valve piston空气量孔air jet燃油滤清器fuel filter沉淀杯sediment bowl串联过滤器in-line filter燃油箱内装过滤器in-tank filter调速器governor飞球式调速器flyball governor调速器governor飞球式调速器flyball governor液压调速器hydraulic governor真空转速调速器vacuum speed governor惯性调速器inertia governor离心调速器centrifugal governor调速器重锤governor weight空气滤清器及进排气系统air cleaner and intake and exhaust sytem 空气滤清器air filter冲压式空气滤清器ram air clearner恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯filter element空气滤清器壳体air filter housing空气滤清器盖air filter cover滤清器密封圈filter seal ring滤网sieve滤纸盘或膜filter paper disc or membrane进气和排气系统intake and exhaust system排气管exhaust pipe排气抽气管exhaust extraction duct扫气泵scavenging pump进气预热装置intake preheater进气歧管intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管cold manifold冲压式进气歧管ram intake manifold排气歧管exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve 超高度歧管high-rise manifold升温横跨管道heat crossover排气横跨管道exhaust crossover预热点hot spot阻风门加热器choke heater热空气导流管hot air duct隔热板heat shield排气再循环阀exhaust -gas-recirculation消声器silencer进气消声器intake silencer排气消声器exhaust silencer金属垫片式消声器steel pack muffler玻璃丝消声器glass pack muffler空洞消声器gutted muffler前排气管front exhaust pipe尾管tail pipe消声器联接管intermediate pipe热空气管hot air pipe曲轴箱通风管crankcase bleed pipe隔声罩acoustic hood进气消声器元件silencer element真空泵vacuum pump指示功率indicated power指示热效率indicated thermal efficiency指示油耗率indicated specific energy consumption示功图indicator diagram冷却系cooling system风冷air cooling水冷water-cooling循环流冷却系cooling recovery system自然循环液冷却系统natural circulation type cooling system热流循环液冷却系统thermo-siphon circulation type cooling system 温差循环液冷却系统gravity circulation water cooling system压力式水冷却系统positive circulation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation cooling system强制循环式化冷系统forced-feed water circulation system封闭式液冷系统sealed cooling system散热器radiator片式散热器finned radiator管式散热器tubular radiator蜂窝式散热器cellular radiator哈里逊式散热器Harrison type radiator带板式散热器ribbon type radiator上水箱upper tank下水箱lower tank涨溢箱expansion tank散热器芯radiator core之字形管散热器芯film core管-片式散热器芯fin and tube core散热器加水口盖radiator filter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩radiator cowl散热器百叶窗radiator shutter散热器保温帘radiator roller blind散热片cooling fin缸盖散热片cylinder head fin缸体散热片cylinder block fin控温装置temperature regulating device恒温器thermostat恒温器主阀thermostat main valve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵water pump水泵体pump casing水泵叶轮water pump impeller旁通进水口water by-pass inlet neck循环泵circulating pump主进水口water main inlet port出水口water outlet port自调式水封self-adjusting seal unit溢流管overflow pipe导流板deflector风扇fan(blower)轴流式风扇axial flow fan离心式风扇centrifugal fan风扇壳体blower casing风扇导流罩fan cowl风扇毂fan hub风扇叶片fan blade风扇叶轮blower impeller风扇导流定子blower stator风扇皮带轮fan pulley三角皮带v-belt风扇护罩fan shroud风扇叶轮叶片impeller vane冷却用空气cooling air风扇导流叶片stator vane强制风冷forced-air cooling自然风冷natural air cooling风道air ducting润滑系lubrication system润滑lubrication气缸上部润滑upper cylinder lubrication 压力润滑pressure-feed lubrication压力润滑法forced lubrication自动润滑automatic lubrication飞溅润滑splash lubrication润滑周期lubrication interval边界润滑borderline lubrication曲轴箱机油油盘crankcase oil pan油底壳oil pan机油盘放油塞sump plug集油器oil collector机油泵oil pump计量式机油泵metering oil pump齿轮式机油泵gear type oil pump转子式机油泵rotor-type oil pump机油泵出油管oil pump outlet pipe放油口oil drain hole油道oil duct断油开关cut-off cock机油散热器oil cooler机油滤清器oil filter机油粗滤器primary oil filter机油精滤器secondary oil filter全流式机油滤清器full-flow oil filter分流式机油滤清器by-pass oil filter离心式机油滤清器centrifugal oil filter整体式滤芯integral filtering element细滤器滤芯filter element滤清器壳filter box滤片filtering disc机油减压器oil pressure relief valve旁通阀by-pass oil filter机油滤网oil strainer加机油孔oil filter cap滤芯轴filter shaft刮片组件cleaning edge机油量尺dipstick机油滤网oil strainer增压器supercharger增压和扫气装置pressure-charging and scavenging unit 增压装置supercharging device涡轮增压器turbo-charger气波增压器comprex pressure wave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass 增压器叶轮supercharger impeller惯性增压inertia supercharging机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging level喘振surge喘振线surge line轴流式涡轮axial-flow turbine脉冲进气ram charging发动机试验engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmospheric conditions大气压力atmospheric pressure进气温度inlet air temperature进气温度inlet air temperature功率校正power correction功率标定power rating功率换算power conversion校正系数correction factor换算系数performance test性能试验performance test起动性能试验starting ability test怠速试验idle running test道路负荷试验road load test各缸工作均匀性试验cylinder variation test背压试验back pressure test最低稳定工作转速试验lowest continuous speed test with load 背部泄漏试验back-leakage test调整试验adjustment test热平衡试验heat balance test快速磨损试验accelerated wear test热冲击试验thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验exhaust analysis test突变负荷试验sudden load change test稳定性试验stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验verification test鉴定试验approval test可靠性试验reliability test耐久性试验durability test定型试验type approval test验收试验acceptance test现场试验field test出厂试验delivery test抽查试验spot check test复查试验re-check test台架试验bench test强化试验hop-up test发动机试验台engine test bed底盘测功机chassis dynamometer测功机dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机electric dynamometer扭矩仪torque meter转速表tachometer温度测量thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪hot wire anemometer电子示功仪electronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission综合排放质量composite mass of exhaust emission排放系数emission factor排放率emission index质量排放量mass emission比排放量brake specific emission排放物控制系统emission control system排气排放物控制系统exhaust emission control system二次空气secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve二次空气转流阀secondary air diverter valve二次空气喷射装置secondary air injection system二次空气喷射管secondary air injection tube二次空气喷射减速压阀secondary air injection relief valve 脉动空气装置pulsating air system二次空气泵secondary air pump曲轴箱排放物控制系统crankcase emission control system 曲轴箱双通风系统crankcase closed system曲轴箱单通风系统crankcase sealed system曲轴箱强制通风装置positive crankcase ventilationPCV阀PCV valve蒸发排放物控制系统evaporative emission control system 活性碳罐贮存装置charcoal canister storage system活性碳罐charcoal canister曲轴箱贮存装置crankcase storage system空气滤清器贮存装置air filter storage system燃油箱止回阀fuel tank check valve油气分离器fuel and vapor separator清除阀furge valve催化转化系统catalytic converting system催化燃烧分析仪catalytic combustion analyzer催化剂catalyst转化器converter催化转化器catalytic converter轴流式转化器AXIAL FLOW TYPE CONVERTER径流式转化器RADIAL FLOW TYPE CONVERTER下流式转化器down flow type converter上流式转化器up flow type converter双床式转化器dual bed converter单床式转化器single bed converter氧化型催化剂oxidation catalyst还原型催化剂reduction catalyst三元催化剂three-way catalyst贵金属催化剂noble metal catalyst普通金属催化剂base metal catalyst稀土催化剂rare earth catalyst催化剂耗损catalyst attrition催化剂收缩catalyst shrinkage催化剂中毒catalyst poisoning比表面积specific surface area空速space velocity载体涂料washcoat双重催化系统dual -catalyst system催化箱catalyst container载体substrate整体式载体monolithic substrate颗粒式载体pelleted substrate转化效率conversion efficiency熄灯温度light-off temperature热态反应系统thermal reacting system热反应器thermal reactor反应式歧管reactive manifold过热保护装置over heating protection system过热警报装置over heating warning system排气口衬套exhaust port liner后燃器after burner排气再循环系EGR system排气再循环exhaust gas recirculation节气门前EGR系统above throttle valve EGR system节气门后EGR 系统below throttle valve EGR system空气比例式EGR系统air proportional EGR system负荷比例式EGR系统load proportional EGR system孔口真空控制式EGR 系统ported vacuum controlled EGR system喉管真空控制式EGR系统venturi vacuum controlled EGR system排气压力控制式EGR系统exhaust pressure controlled EGR system声速控制式EGR系统sonic controlled EGR system电子控制式EGR系统electronic controlled EGR system EGR冷却器EGR cooler EGR过滤器GER filter EGR控制阀EGR control valve EGR调压阀EGR pressure regulator再循环排气EGR gas再循环排气率EGR rate点火和喷油时刻控制系统ignition and injection timing control system 点火时刻控制系统ignition timing control system减速点火提前控制装置deceleration spark advance control推迟喷油时刻控制系统retarded injection timing control system。

航空发动机常用汉英词汇

学而不思则惘，思而不学则殆汉英分类词汇航空发动机类型Aero-Engine Models超高涵比发动机ultra high bypass engine超音速冲压喷气发动机scramjet engine冲压喷气发动机ram-jet engine带推力转向系统的发动机engine with thrust deflector system带自由涡轮双轴涡轮轴喷气发动机twin-spool turbo-shaft with free-power turbine单轴涡轮喷气发动机single-spool turbo-jet engine低涵比发动机low bypass turbofan反向旋转发动机contra-rotation engine高涵比发动机high bypass turbofan后风扇涡轮喷气发动机aft fan turbo-jet engine 活塞式发动机piston(-and-cylinder) engine // piston-driven engine桨扇发动机prop-fan engine离心涡轮喷气发动机centrifugal turbo-jet engine 脉冲喷气发动机pulse jet engine前风扇涡轮喷气发动机front fan turbo-jet engine 燃气轮机gas turbine engine三轴桨扇发动机three-shaft prop-fan engine三轴涡轮前风扇涡轮发动机triple-spool front fan turbo-jet双轴外涵涡轮喷气发动机twin-spool by-pass turbo-jet双轴涡轮风扇发动机twin-spool turbo-fan engine 同向旋转发动机co-rotation engine外骨架发动机exo-skeletal engine涡轮冲压喷气发动机turbo/ram jet engine涡轮风扇发动机turbofan engine涡轮火箭发动机turbo-rocket engine涡轮螺旋桨发动机turboprop engine涡轮喷气发动机turbojet engine涡轮轴发动机turbo-shaft engine轴流涡轮喷气发动机axial flow turbo-jet engine 型面profile型面座标图aerofoil ordinate chart型式form轴流式压气机axial (flow) compressor函道duct函道比by-pass函道风扇ducted-fan中介机匣intermediate case燕尾形样dovetail root叶片vane（一般指静子叶片）压气机compressor压气机机匣compressor case 效率efficiency压气机盘compressor disc压缩比compression ratio牙底root涡轮导向器turbine nozzle涡轮盘turbine disc燃烧室burner // combustion chamber // combustor燃烧室外套combustion outer case燃油导管discharge nozzle燃油滤fuel filter燃油喷咀fuel atomizer // fuel spray nozzle燃油消耗量fuel consumption火焰筒liner扩散器机匣diffuse case加力燃烧室afterburner航空发动机叶片术语Terms of Aero-Engine Airfoils叶片类型Type of Airfoils动叶blade // bucket静叶vane空心叶片hollow blade // core blade实心叶片solid blade涡轮导向器turbine nozzles涡轮导向器扇形段turbine nozzle segment涡轮导向器叶片turbine nozzle vane // nozzle guide vane (ngv)涡轮工作叶片turbine blade // bucket涡轮静子叶片turbine nozzle vane // nozzle guide vane (ngv)涡轮叶轮turbine wheel涡轮叶片turbine blades & vanes // buckets涡轮转子叶片turbine blade // bucket压气机定子叶片compressor vane // vane压气机工作叶片compressor blade // blade压气机叶轮compressor impeller // compressor wheel压气机叶片compressor blades & vanes压气机整流叶片compressor vane // vane压气机转子叶片compressor blade // blade叶片的结构特点Characteristics of Airfoil Structure基体部分base榫头tip // cog // fir-tree // root // tenon叶根blade root // root // vane tang叶冠shroud // tip platform // tip shroud叶身blade body叶型部分aerofoil // profile缘板platform // shroud叶片的主要名称Key Terms of Airfoil Body基体base进气边/前缘leading edge理论叶型theoretical developed airfoil/profile排气边/后缘trailing edge // exhaust edge弦chord型线airfoil curve叶背blade back // convex side // blade convex叶盆blade basin // vane basin // blade/vane concave叶片阻尼台blade damper // clapper // mid-span 叶身blade body叶型公差airfoil tolerance叶型理论airfoil theory叶型剖面airfoil section中弧线airfoil mean line工装Tooling标准件master piece // standard part // tool master 标准块master block // reference block测具gauge // measuring fixture // measuring tool 测头feeler // gauge head measuring head // stylus 车床夹具lathe fixture车刀lathe tool// cutter// turning tool吊具lifting tool夹具fixture饺孔夹具reaming fixture // reaming jig孔位置度测具hole true position gauge拉刀broach (Bro.) // broaching cutter拉削夹具broaching fixture刨削夹具planner fixture钳工工具bench-work tool丝套insert // thread insert丝锥taper // (screwing）tap镗刀boring cutter镗杆boring bar (B/bar) // boring spindle镗孔夹具boring fixture // boring jig铣槽工具grooving tool铣床夹具milling jig铣床铣槽刀milling machine // miller铣铣槽刀刀milling cutter // milling tool铣削夹具milling fixture钻铰刀drill reamer 钻铰复合刀具combined drill and reamer钻具jig钻孔铰孔夹具drilling and tapping fixture钻孔样板drill template （DRT）// drilling template钻模(drill) jig钻模板drill plate （DRP）钻模与夹具jigs and fixtures钻套jig bush钻套jig bush(ing)钻头bit // drill // drilling bit机械加工术语Terms for Machining半精加工semi-finishing // semifinishing machining插slotting车turning车床lathe// turning machine车床研磨lathe lapping车端面facing车螺纹thread turning车螺纹/螺纹加工thread/threading车削turning车削螺纹cut thread成形法forming冲头blanking ram // piercer // punch // ram head // slider冲压(punch) pressing冲压加工stamping冲压件pressing //stamping穿孔/套孔trepan/trepanning粗加工roughing machining锉file倒角deburr // chamfer倒角/去毛刺deburr(ing)倒棱chamfer电解抛光electrochemical polishing // electrolytic polishing // electro-polishing电解蚀刻与抛光electrolytic etching and polishing调整法machining on preset machine tool定位locating // location对刀to size // tool setting仿形法copying夹紧clamping饺reaming饺孔reaming饺孔机reaming machine饺孔钻reamer drill饺铆钉孔ream a rivet hole精加工finishing // finish machining锯sawing锯背back of the saw锯槽kerf锯齿serration锯齿铣sawtooth milling拉削broaching冷装shrinkage fitting铆rivet(ing)铆钉rivet磨床grind // grinding machine磨端面face grinding磨料abraser // abrasive material // grinding compound磨削加工abrasive machining抛polish抛光buffing // burning // polish (Pol.)刨planing// shapering刨槽fillister // slot shaping刨齿gear shaper cutting // gear-shaping刨床planer // planing machine// shaper刨削shaping去毛刺deburring // fin cutting镗boring镗车两用机床boring lathe镗床borer // boring machine镗孔boring // borizing （金刚石）镗磨联合机床combined boring and honing machine镗钻两用机床boring and drilling machine铣mill // milling铣槽slot milling铣镗床milling-borer // milling and boring machine铣钻联合机床combined drill and mill machine铣钻两用机床milling and drilling machine旋spin旋锻spin forging // rotary forging // rotary swaging旋锻机spin forging machine // rotary forging machine // rotary swaging machine旋压spinning旋压成型stretch planishing // spin forming压装press fitting研lapping研齿gear lapping研磨lapping找正aligning // to center align装夹set-up装配assembly钻drill(ing)钻床drilling machine钻孔drilling钻埋头孔countersink表面处理（镀层、涂漆和金属喷镀）Surface treatment （Plating，Paining & Metal sparying）涂层不良imperfectly coated spots涂层过厚thickening涂层凸起lifting of the coating, protrusion, or lifting冲压Punch尺寸检验dimension inspecting基准datum技术条件technical condition加工fabricate夹clamping夹紧面clamping surface夹具fixture钻孔drill钻头drill图纸及工艺规程常用词汇EverydayVocabularies on Working Drawings &W.P.S尺scale尺寸dimension // size尺寸单向极限single of size尺寸过大oversize尺寸过小undersize尺寸极限limit of size尺寸最大极限maximum of size尺寸最大余量极限maximum metal of size尺寸最小极限minimum of size齿根root处理treatment吹砂blast // abrasive blasting垂直度perpendicularity // squareness垂直度公差squareness tolerance单位燃油消耗量specific fuel consumption单位压力unit pressure单位装配件assembly unit单向公差unilateral tolerance单向公差域bilateral tolerance zone氮化nitriding当量equivalent挡块stop刀柄holder刀杆cutter bar刀痕scar // tool mark等离子喷镀plasma spray等值equivalent低压压气机LP compressor地面试车ground run典型加工typical operation防锈rust protection // rust proof仿形copy仿形铣床copying milling machine // duplicator 仿型加工form machine高速钢high speed steel高速工具钢high speed tool steel高温合金high temperature alloy高压压气机HP compressor根root根切undercut公差tolerance公差带tolerance band公称尺寸nominal size功能function功能尺寸function dimension功能要求functional requirement构造尺寸constructional dimension固定fasten固定工具fastening tool故障defect // blemish // failure // fault // imperfection // trouble故障分析trouble shooting关键零件critical part观点view过盈interference过盈配合interference fit过载overload互换性interchangeability互换性组件interchangeable assembly花键splined shaft花键轴splined shaft火裂fire cracks机床machine (tool)机匣case // casing基本尺寸base dimension // basic size基本公差basic tolerance基本数basic member基本锥体basic taper基孔制hole basis limit system基线basic line基轴制shaft basis基轴制shaft basis limit system基准data // reference基准尺寸datum dimension基准点datum point基准件basic member 基准角basic angle基准面datum face // datum plane基准线datum line // zero line基准叶片master vane几何公差geometrical tolerance几何精度accuracy geometrical加工制造fabricate夹紧fastening夹具clamping apparatus // dogging tool // fixture // holding device // jig检验装置checker节径pitch diameter精度accuracy // precision精锻precision forging精加工finishing精磨precision ground精确长度exact length精调fine adjustment // accurate adjustment //precision adjustment孔bore // hole框flame拉床broacher // broaching machine拉刀broacher拉销broach离心式压气机centrifugal compressor离心铸造centrispum casting iron立式车床vertical lathe立式钻床upright drill螺母nut螺栓bolt名义尺寸base size // nominal size内径inner diameter内裂internal crack内外函发动机by-pass engine内应力internal stress内圆磨床internal grinding machine耐磨性resistance to wear耐热钢heat resisting steel耐热合金heat-resisting啮合mesh啮合线action line扭转twisting排气边trailing edge排气喷口exhaust nozzle盘disc抛光polishing抛光机polisher // burnishing wheel刨平plane泡疤blister配合fit // matching // mating配合等级classes of fit // grade of fit配合间隙class of fit配合类型types of fit配合容差fitting allowance配合直径snap diameter配合制system of fits配件mating piece喷口nozzle喷丸peening // shot-blasting喷丸处理shot peening喷雾器atomizer喷嘴nozzle批生产mass production疲劳断裂fatigue fracture匹配matching片sheet偏心的eccentric偏心距eccentric distance偏心轮eccentric偏心套eccentric bushing偏心轴eccentric axis偏心装置eccentric偏移deviation漆paint切断parting切面cutting切切削深度depth of cut切头cropping切削cut切削工具cutter切削加工machining轻合金light alloy轻微的slight清楚的clear清理cleaning清漆层不好poorly varnished film区域zone曲度curve曲面curved surface曲线curve屈服yield屈服点yield point屈服强度yield strength屈服应力proof stress // yield stress缺口敏感性notch sensitivity缺陷blemish // defect // failure // fault // imperfection热脆性red shortness热裂hot crack热裂纹clink热损heat waste容差allowance熔化smelt (ing)蠕变creep 设计design设计草图rough plan设计尺寸design size设计角design angle伸长elongation伸长率elongation失速stall（飞机）湿吹砂vapour blast时间表schedule时效ag(e)ing时效处理seasoning识别号identification number实际尺寸actual size实际有效直径virtual effective diameter式样form // manner事故accident // failure视图view试车test run // trial run试件test piece试验examine // test试验参数test data试样coupon // (test) sample // test specimen试样长度sample释放release手册manual手段means寿命limit of life数number数据data数量quantity说明书description // specification榫头root调正adjustment调质improvement跳动量runout凸起overfill凸台boss凸缘collar // flange图scheme图板drawing board图号drawing number图形机体feature图样draft // drawing图纸drawing (sheet)图纸比例drawing scale图纸技术要求drawing call-out涂层不良imperfectly coated spots涂层过厚thickening涂层凸起lifting of the coating, protrusion, or lifting涂漆paint推荐尺寸preferred size推力thrust推力比thrust ratio椭圆度ovality外部检查visual inspection外函道by-pass duct外螺纹external screw thread外形outline外圆磨床circular grinding machine位置location位置公差positional tolerance蜗杆worm蜗轮work wheel卧式钻镗床horizontal boring & drilling machine 误差error习惯表示法conventional representation铣床milling machine铣刀milling现场site // spot相当的equivalent相应值equivalent消除应力stress relieved // stress released消耗consumption销钉pin销孔bore // pin hole销子pin斜度angularity (tolerance)压板clamp (plate)氩弧焊argon-arc welding应变strain应变时效strain ageing应力stress应力腐蚀裂纹stress corrosion crack应力消除stress relieving应力-应变曲线stress strain curve应力-应变图stress strain diagram圆度circularity // roundness圆滑smoothness圆心center of circle圆柱度cylindricity直径diameter制度system制造manufacture质量quality质量验收标准quality acceptance standard中心距center distance中心孔center hole轴shaft轴承bearing轴线axis轴线axis主喷咀main nozzle 铸造casting铸造组织casting iron structure专门技术know-how专门铣床planomilling machine专用工具special tool专用工装special tooling专用设备special purpose machine专用铣床production machine转换reset转子叶片blade装备device装夹mount装配assembly // mount装配车间assembling shop // assembly shop // erecting shop // fitting shop装配间隙fit clearance装配件assembly装配图assembly drawing // erection drawing装箱退火close annealing装置device锥齿轮bevel gear锥度taper锥螺纹taper thread锥面conical surface锥体slow object // taper总尺寸外形尺寸overall dimension总体布置图general layout总装车间assembly department总装件assembly // general assembly总装图general layout组合件joint组件assembly组装件sub assembly钻drill钻床drill machine钻具jig钻孔drill钻套drill jig bush钻头号drill number最大长度max length最大间隙major clearance最大推力full thrust // top thrust最大直径major diameter最小长度min length最小间隙minor clearance最小直径minor diameter缺陷解释Interpretation of Defects凹陷undercutting （在母材上沿焊接边的沟槽或充填不足）变形deformation （在加工时未能保持住形状不变或与相邻部有不顺滑转接）电解腐蚀electrolytic action（不同金属间的电蚀作用造成的缺陷）断裂fracture（受力过大造成的破坏）开裂flaw外贸常用词语和术语Everyday Vocabularies of Foreign Trade询盘Inquiry把某物交付给某人to deliver sth to sb把询价记录在卷to keep the inquiry on file办理交货to effect delivery // to make delivery还盘Counter Offer还盘counter offer享有盛誉enjoy great popularity与某人达成交易conclude business with sb. 达成交易close business // close a deal // close a transaction // close a bargain价格Price成本加保险费运费价cost, insurance & freight (C.I.F.)成本加运费价cost & freight (CFR)船上交货free on board (F.O.B)底价floor price货币currency价格偏低on the low side价格条件price terms廉价出售 a bargain sale市场价market price讨价还价bargain为某事拼命讨价还价drive a hard bargain over sth.与某人成交make a bargain with sb最低价rock-bottom price学而不思则惘，思而不学则殆。

发动机中英文术语

发动机中英文术语 ( Carrot Download) 2007-3-14发动机 engine内燃机 intenal combusiton engine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发动机 compression ignition engine往复式内燃机 reciprocating internal combustion engine 化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机 water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 multiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead camshaft engine V形发动机 V-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical engineW形发动机 w-engineI形发动机 I-engineL形发动机 L-engineF形发动机 F-engine二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程 expansion-exchange stroke换气压缩行程 exchange-compression stroke止点 dead center上止点 top dead center(upper dead center)下止点 lower dead center(bottom dead center)上止点前 budc(before upper dead center)上止点后 atdc(after top dead cetner)下止点前 bbdc(before bottom dead center)下止点后 abdc(after bottom dead center)缸径 cylinder bore缸径与行程 bore and stroke空气室 energy chamber气缸余隙容积 cylinder clearance volume燃烧室容积 combustion chamber volume气缸最大容积 maximum cylinder volume压缩室 compression chamber排气量 displacement发动机排量 engine displacement活塞排量 piston swept volume气缸容量 cylinder capacity单室容量 single-chamber capacity容积法 volumetry压缩比 compression ratio临界压缩比 critical compression ratio膨胀比 expansion ratio面容比 surface to volume ratio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio燃空比 fuel air ratio燃料当量比 fuel equivalence ratio扭矩 torque单缸功率 power per cylinder升功率 power per liter升扭矩 torque per liter升质量 mass per liter减额功率 derating power输出马力 shaft horsepower马力小时，马力时 horsepower-hour总马力 gross horse power总功率 gross power净功率 net power燃油消耗量 fuel consumption比燃料消耗率 specific fuel consumption空气消耗率 air consumption机油消耗量 oil consumption有效马力 net horse power额定马力 rated horse power马力重量系数 horsepower-weight factor制动功率 brake horse power制动热效率 brake thermal efficiency总效率 overall efficiency排烟极限功率 smoke limiting horsepower功率曲线 power curve机械损失 mechanical loss机械效率 mechanical efficiency有效热效率 effective thermal efficiency充气系数 volumetric efficiency过量空气系数 coefficient of excess air适应性系数 adaptive coefficient扭矩适应性系数 coefficient of torque adaptibility 转速适应性系数 speed adaptive coefficient强化系数 coefficient of intensification校正系数 correction factor换算系数 conversion factor活塞平均速度 mean piston speed发动机转速 engine speed (rotational frequency)怠速转速 idling speed经济转速 economic speed起动转速 starting speed最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque最高空转转速 maximum no load governed speed调速 speed governing超速 overspeed怠速 idling转速波动率 speed fluctuation rate工况 working condition(operating mode)额定工况 declared working condition变工况 variable working condition稳定工况 steady working condition空载 no-load全负荷 full load超负荷 overload部分负荷 part load充量（进气） charge旋转方向 direction of rotation顺时针 clockwise逆时针 counter-clockwise左转 left-hand rotation右转 right-hand rotation外径 major diameter中径 pitch diameter内径 minor diameter径向间隙 radial clearance发动机性能 engine performance加载性能 loading performance起动性能 starting performance加速性能 acceleration performance动力性能 power performance排放性能 emission performance空转特性 no load characteristics负荷特性 part throttle characteristics调速特性 governor control characteristics 万有特性 mapping characteristics稳定调速率 steady state speed governing rate 气缸体和气缸盖 cylinder block and head气缸体 cylinder block整体铸造 cast inblock (cast enblock)发动机罩 engine bonnet气缸体加强筋 engine block stiffening rib气缸 cylinder（转子机）缸体 stator缸径 cylinder bore气缸体机架 cylinder block frame气缸盖 cylinder head配气机构箱 valve mechanism casing气缸体隔片 cylinder spacer气缸盖密封环 cylinder head ring gasket气缸盖垫片 cylinder head gasket气缸套 cylinder liner(cylinder sleeve)干式缸套 dry cylinder liner湿式缸套 wet cylinder liner气缸水套 water jacket膨胀塞 expansion plug防冻塞 freeze plug气缸壁 cylinder wall环脊 ring ridge排气口 exhaust port中间隔板 intermediate bottum导板 guideway创成半径（转子机） generating radius缸体宽度（转子机） operating width机柱 column燃烧室 combustion chamber主燃烧室 main combustion chamber副燃烧室 subsidiary combustion chamber预燃室 prechamber涡流燃烧室` swirl combustion chamber分开式燃烧室 divided combustion chamber涡流式燃烧室 turbulence combustion chamber半球形燃烧室 hemispherical combustion chamber浴盆形燃烧室 bathtub section combustion chamberL形燃烧室 L-combustion chamber楔形燃烧室 wedge-section combustion chamber开式燃烧室 open combustion chamber封闭喷射室 closed spray chamber活塞顶内燃烧室 piston chamber爆发室 explosion chamber燃烧室容积比 volume ratio of combustion cahmber燃烧室口径比 surface-volume ratio of combustion chamber 通道面积比 area ratio of combustion chamber passage曲轴箱通气口 crankcase breather凸轮轴轴承座 camshaft bearing bush seat定时齿轮室罩 camshaft drive(gear)cover曲轴箱检查孔盖 crankcase door曲轴箱防爆门 crankcase explosion proof door主轴承盖 main bearing cap气缸盖罩 valve mechanism cover飞轮壳 flywheel cover扫气储器 scavenging air receiver活塞 piston裙部开槽活塞 split skirt pistonU形槽活塞 U-slot piston滚花修复活塞 knurled piston圆顶活塞 dome head piston平顶活塞 flat head piston凸顶活塞 crown head piston(convex head piston)凹顶活塞 concave head piston阶梯顶活塞 step-head piston筒形活塞 trunk piston椭圆形活塞 oval piston抗热变形活塞 autothermic piston不变间隙活塞 constant clearance piston镶因瓦钢片活塞 invar strut piston直接冷却式活塞 direct-cooled piston间接冷却式活塞 indirect cooled piston滑裙活塞 slipper piston活塞速度 piston speed活塞顶部 piston head活塞裙部 piston skirt整体活塞裙 solid skirt活塞裙扩大衬簧 piston skirt expander滑履式活塞裙 slipper skirt隔热槽 heat dam活塞标记 piston mark活塞销 piston pin活塞销孔 piston pin boss活塞销衬套 piston pin bushing全浮式活塞销 full-floating piston pin半浮式活塞销 semifloating piston pin固定螺钉式活塞销 set screw piston pin活塞环 piston ring组合式活塞环 compound piston ring同心活塞环 concentric piston ring偏心活塞环 eccentric piston ring自由环 free ring闭合环 closed ring梯形环 keystone ring半梯形环 half keystone ring矩形环 rectangular ring油环 oil control ring开槽油环 slotted oil control ring螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander双坡口油环 double bevelled oil control ring内上坡口 internal bevel top内下坡口 internal bevel bottom边缘坡口油环 bevelled-ege oil control ring刮油环 scrapper ring钩形环 napier ring镀铬活塞环 chrome plated piston ring活塞衬环 piston ring expander活塞环槽 piston ring groove活塞环区 ring zone活塞环岸 piston ring land活塞环内表面 back of ring曲柄连杆机构 connecting rod中心曲柄连杆机构 central-located connecting rod偏心曲柄连杆机构 offset connecting rod铰接曲柄边杆机构 hinged connecting rod连杆 connecting rod连杆小头 connecting rod small end连杆大头 connnecting rod big end连杆杆身 connecting rod shank副连杆 slave connecting rod叉形连杆 fork-and-blade connecting rod 主连杆 main connecting rod方形连杆 boxed rod绞链式连杆 hinged type connecting rod 活节式连杆 articulated connecting rod 连杆盖 connecting rod cap连杆轴承 connecting rod bearing曲轴 crankshaft整体式曲轴 one-piece crankshaft组合式曲轴 assembled crankshaft右侧曲轴 right-hand crankshaft左侧曲轴 left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端 crankshaft front end曲轴主轴颈 crankshaft main journal轴颈重叠度 shaft journal overlap圆角 fillet主轴承main bearing曲轴止推轴承 crankshaft thrust bearing 薄臂轴瓦 thin wall bearing shell曲轴油道 crankshaft oil passage曲柄 crank曲柄臂 crank arm曲柄销 crank pin轴套 bush曲柄转角 crank angle曲柄半径 crank radius抛油圈 oil slander角度轮 degree wheel动平衡机 dynamic balancer平衡重 balancer weight扭振减振器 torshional vibration damper 扭振平衡器 torsion balancer谐振平衡器 harmonic balancer振动平衡器 vibration balancer曲轴链轮 crankshaft sprocket转子轴颈 rotor journal偏心轴 eccentric shaft曲轴箱 crankcase闭式曲轴箱通风装置 closed-crankcase ventilating system 飞轮 flywheel飞轮齿圈 flywheel ring gear飞轮芯棒 cantilever飞轮芯轴 flywheel spindle飞轮的惯量矩 flywheel moment of inertia飞轮标记 flywheel mark当量系统 equivalent system当量轴长 equivalent shaft length一级往复惯性力 reciprocating inertia force,1st order 二级往复贯性力 reciprocating inertia force, 2nd order 离心惯性力 centrifugal inertia force配气机构 valve gear凸轮轴 camshaft凸轮 cam整体式凸轮轴 one-piece camshaft组合式凸轮轴 assembled camshaft凸轮轴驱动机构 camshaft drive赛车用凸轮轴 race camshaft凸轮轴轴颈 camshaft bearing journal凸轮轴轴承 camshaft bearing凸轮轴偏心轮 camshaft eccentric凸轮轴链轮 camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮 camshaft gear wheel进口凸轮 inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓 cam contour凸轮包角 cam angle凸轮升程 cam-lobe lift凸轮尖 cam nose凸轮从动件 cam follower齿轮传动机构gear drive正时齿轮 timing gear链传动机构 chain drive链轮 sprocket wheel链轮盘 chain sprocket正时链条 timing chain带齿皮带 toothed timing belt链条张紧轮 chain tension gear半速齿轮 half speed gear正时齿轮刻印记号 timing gear punch mark气门 valve进气过程 intake process换气过程 gas exchange process扫气过程 scavenging process给气比 delivery ratio分层充气 stratified charge充量系数 volumetric efficiency涡流比 swirl rate进气涡流 intake swirl螺旋进气道进气 helical duct intake导流屏式气门进气 masked valve intake切向进气道进气 tangential duct intake进气紊流 intake trubulence进气提前角 intake advance angle进气持续角 intake duration angle进气迟后角 intake lag angle进面值 time-area value气门升程 valve lift气门正时 valve timing扫气口面积 scavenging port area菌形气门 mashroom valve, poppet valve钠冷却气门 sodium filled valve(natrium cooled valve) 双气门 dual valve进气门 intake valve (suction valve,inlet valve)排气门 exhaust valve顶置气门 overhead valve侧置气门 side valve倾斜气门 inclined overhead valve直立气门 vertical overhead valve套筒式滑阀 sleeve valve气门机构 valve gear直接式气门驱动机构 direct valve gear间接式气门驱动机构 indirect valve gear气门杆 valve stem加大气门杆 oversize valve stem气门头 valve head气门工作面 valve face气门边限 valve margin气门弹簧座 valve-spring retainer气门锁片 valve key气门间隙调节螺钉 valve lash adjusting screw气门旋转器 valve rotator气门室 valve cage气门油封 valve oil seal气门口 valve port气门座 valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角 valve seat angle气门座宽度 valve seat width气门挺杆 valve tappet(valve lifter)液力挺杆 hydraulic tappet(lifter)无间隙挺杆 zero-rush tappet (non-clearance tappet)筒形挺杆 barrel type tappet油压挺杆 ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位 tappet rotation排气门挺杆 exhaust valve lifter气门导管 valve guide气门杆导管 stem guide气门重叠度 stem overlap气门开启持续时间 valve duration气门正时标记 valve timing sign气门弹簧 valve spring气门内弹簧 inner valve spring气门外弹簧 outer valve spring刚性缓冲弹簧 stiff buffer spring上紧弹簧 energizing spring防振气门弹簧 non-surging spring弹簧座圈 spring retainer蝶形弹簧 belleville spring滚柱 roller气门室盖 valve chamber cover摇臂 rocker arm高升程摇臂 high lift rocker arm摇臂轴 rocker arm shaft推杆 push-rod摇臂支架 rocker arm bracket气门摇臂室罩 valve rocker chamber cover导向轮 guide wheel导杆 slide bar导轨 slide rail张紧轮 tensioning wheel链条张紧调节装置 assembly chain tension adjuster张紧带轮 tensioning pulley传动带张紧装置 belt tensioner同步驱动皮带 synchronous belt同步驱动皮轮 synchronous belt pulley供油系 fuel system控制燃烧系统 controlled combustion system反湿气装置 antipercolator电子燃油喷射 electronic fuel injection蒸气回收装置 vapor recovery system燃油蒸气回收系统 fuel vapor recovery system液体回收装置 liquid withdrawal system恒量净化管 constant purge line碳罐净化管 canister purge line供油量 fuel delivery循环供油量 fuel delivery per cycle额定供油量 rated fuel delivery怠速供油量 idling speed fuel delivery供油规律 fuel supply rate curve油量调节装置 fuel control unit供油提前角 fuel supply advance angle进油计量 inlet metering几何供油行程 geometric fuel delivery stroke供油率 fuel supply rate燃油通道 fuel gallery有效行程 effective stroke剩余行程 remainder stroke变行程计量 variable stroke metering等容卸载 constant volume unloading变容卸载 variable volume unloading收缩容积 retraction volume燃油喷油装置 fuel injection equipment燃油喷射泵 fuel injection pump滚轮式燃油喷射泵 roll fuel injection pump凸轮轴式燃油喷射泵 camshaft fuel injection pump直列式燃油喷射泵 in-line fuel injection pump伺服式燃油喷射泵 servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵 high flanged-mounted fuel injection pump侧向安装燃油喷射泵 side-mounted fuel injection pump端部突缘安装式燃油喷射泵 end flange-mounted fuel injection pump V形燃油喷射泵 vee fuel injection pump脉动式燃油喷射泵 jerk fuel injection pump螺纹安装燃油喷射泵 screw-mounted fuel injection pump蓄能式燃油喷射泵 accumulator fuel injection pump往复式燃油喷射泵 reciprocating fuel injection pump驱动轴式燃油喷射泵 driveshaft fuel injection pump单缸式燃油喷射泵 single cylinder fuel injection pump圆柱式燃油喷射泵 cylindrical fuel injection pump旋转式燃油喷射泵 rotary fuel injection pump分配式燃油喷射泵 distributor fuel injection pump多缸燃油喷射泵 multicylinder fuel injection pump框架安装式燃油喷射泵 cradle mounted injection pump喷油始点 fuel injection beginning喷油终点 fuel injection end喷油持续角 fuel injection duration angle喷油延迟 injection delay引燃喷射 pilot injection启喷压力 injection starting pressure峰值喷油扭矩 peak injection torque峰值喷油压力 peak injection pressure喷油泵油缸数目 number of cylinders of an injection pump 无气喷射 solid injection喷射正时 injection timing集中喷射 group injection喷油器 injector整体式喷油器 unit injector喷嘴 nozzle轴针式喷嘴 pintle type nozzle环槽式喷嘴 annular slot nozzle孔式喷嘴 hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴 orifice plate nozzle开式喷嘴 open nozzle闭式喷嘴 closed nozzle喷油提前器 timing advance unit喷射泵壳体 injection pump housing针阀 needle芯轴 central spindle喷嘴壳体 nozzle body针阀升程 needle lift喷嘴盖形螺母 nozzle cap nut喷油器壳体 nozzle holder突缘安装喷油器壳体 flanged-mounted injection nozzle holder 燃油喷射泵传动装置 transmision of an injection pump喷嘴锥体 nozzle hole cone柱塞 plunger柱塞套 barrel柱塞行程 plunger stroke喷孔 spray orifice海拔控制器 altitude control提前器飞锤 flyweight喷孔长径比 ratio of nozzle hole length nozzle diameter喷嘴液动力特性 nozzle hydrokinetic characteristics动态相位 dynamic phase喷孔面积 nozzle hole area喷嘴流通特性 nozzle flow characteristic喷油背压 injection back pressure高压油管 high pressure pipe平均喷油扭矩 mean injection torque喷油总效率 overall pumping efficiency峰值喷油压力 injection peak pressure预行程 prestroke收缩行程 retraction stroke燃油箱 fuel tank油箱盖 fuel tank油位表 fuel level gauge注油控制装置 fill control system汽油箱 gasoline tank( petrol tank)汽油供给管 gasoline feed pipe加油管 filler tube放油螺塞 drain plug吸油管 suction pipe刚性燃油管 rigid fuel pipe进油孔 fuel feed hole供油管 supply pipe通气管 bleeding pipe通气管 bleeding pipe泄油阀 spill valve泄油孔口 spill port进油阀 inlet valve最大油量限制器maximum fuel stop滴油 dribble燃油表 fuel gauge输油泵 feed pump燃油泵 fuel pump附装燃油箱中的电动燃油泵 tank-mounted eletric fuel pump 机械式燃油泵 mechanical fuel pump膜片式燃油泵 diaphragm fuel supply pump叶片式供油泵 vane fuel supply pump活塞式输油泵 piston type fuel supply pump齿轮式输油泵 gear fuel supply pump电动燃油泵 eletric fuel pump带真空泵的汽油泵 vacuum pump with fuel pump起动加油器 primer起动给油杆 primer lever燃油泵上体 fuel pump body燃油泵下体 fuel pump base燃油泵盖 bowl cover进油口接头fuel inlet neck出油口接头 fuel discharge port输出阀 delivery valve泵油元件 pump element回油阀部件 fuel return valve assembly化油器 carburetor化油器系统 carburetor circuit简单化油器 elementary carburetor单腔化油器 single-barrel carburetor双腔并动化油器 two-barrel dual carburetor双腔分动化油器 two-barrel duplex carburetor四腔化油器 four-barrel carburetor上吸式化油器 updaught carburetor下吸式化油器 downdraught carburetor平吸式化油器 horizontal carburetor侧吸式化油器 side-draft-carburetor高海拔补偿式化油器 altitude compensating carburetor 化油器附加器 adaptor carburetor双腔式化油器 twin-choke carburetor固定喉管式化油器 fixed venturi carburetor可变喉管化油器 variable venturi carburetor化油器接头 carburetor adaptor阻风门 choke valve阻风活塞 choke piston阻风板 choke plate自动阻风门 automatic choke阻风门拉钮 choke button电控自动阻风门 electric-assisted choke阻风管 choke tube喉管 venturi双重或三重喉管 double & triple venturi阻风门拉线 choke cable化油器小喉管 booster venturi浮子系 float system浮子 float环形浮子 annular float同心式浮子 concentric float浮子支销 float hinge pin浮子针阀 float needle valve阀针 valve needle浮子油面 float level浮子臂 float arm侧置浮子室式 side float type怠速阀 idle valve怠速针阀 idle needle省油器 economizer省油器阀 economizer valve辅助空气阀 auxiliary air-valve加速油井 accelerating well加速泵 accelerating pump加速泵喷嘴 accelerating pump nozzle油门 throttle手油门 hand throttle节气门操纵手柄 throttle control lever真空加浓器 vacuum booster加浓器 excess fuel device量孔体 jet block怠速量孔 idle metering jet主量孔 main metering jet剂量阀活塞 dosage valve piston空气量孔 air jet燃油滤清器 fuel filter沉淀杯 sediment bowl串联过滤器 in-line filter燃油箱内装过滤器 in-tank filter调速器 governor飞球式调速器 flyball governor调速器 governor飞球式调速器 flyball governor液压调速器 hydraulic governor真空转速调速器 vacuum speed governor惯性调速器 inertia governor离心调速器 centrifugal governor调速器重锤 governor weight空气滤清器及进排气系统 air cleaner and intake and exhaust sytem 空气滤清器 air filter冲压式空气滤清器 ram air clearner恒温控制式空气滤清器 thermostatic controlled air cleaner油浴式空气滤清器 oil bath air cleaner纸质空气滤清器 paper air clearner旋流管式空气滤清器 swirl tube air filter滤清器滤芯 filter element空气滤清器壳体 air filter housing空气滤清器盖 air filter cover滤清器密封圈 filter seal ring滤网 sieve滤纸盘或膜 filter paper disc or membrane进气和排气系统 intake and exhaust system排气管 exhaust pipe排气抽气管 exhaust extraction duct扫气泵 scavenging pump进气预热装置 intake preheater进气歧管 intake manifold进气歧管真空度 intake manifold vacuum冷式进气歧管 cold manifold冲压式进气歧管 ram intake manifold排气歧管 exhaust manifold脉冲式排气歧管 pulse exhaust manifold等压排气歧管 constant pressrue exhaust manifold排气歧管热量控制阀 exhaust manifold heat control valve超高度歧管 high-rise manifold升温横跨管道 heat crossover排气横跨管道 exhaust crossover预热点 hot spot阻风门加热器 choke heater热空气导流管 hot air duct隔热板 heat shield排气再循环阀 exhaust -gas-recirculation消声器 silencer进气消声器 intake silencer排气消声器 exhaust silencer金属垫片式消声器 steel pack muffler玻璃丝消声器 glass pack muffler空洞消声器 gutted muffler前排气管 front exhaust pipe尾管 tail pipe消声器联接管 intermediate pipe热空气管 hot air pipe曲轴箱通风管 crankcase bleed pipe隔声罩 acoustic hood进气消声器元件 silencer element真空泵 vacuum pump指示功率 indicated power指示热效率 indicated thermal efficiency指示油耗率 indicated specific energy consumption示功图 indicator diagram冷却系 cooling system风冷 air cooling水冷 water-cooling循环流冷却系cooling recovery system自然循环液冷却系统 natural circulation type cooling system热流循环液冷却系统 thermo-siphon circulation type cooling system 温差循环液冷却系统 gravity circulation water cooling system压力式水冷却系统 positive circulation cooling system加压式冷却法 pressure type cooling水泵循环冷却系统 pump circulation cooling system强制循环式化冷系统 forced-feed water circulation system封闭式液冷系统 sealed cooling system散热器 radiator片式散热器 finned radiator管式散热器 tubular radiator蜂窝式散热器 cellular radiator哈里逊式散热器 Harrison type radiator带板式散热器 ribbon type radiator上水箱 upper tank下水箱 lower tank涨溢箱 expansion tank散热器芯 radiator core之字形管散热器芯 film core管-片式散热器芯 fin and tube core散热器加水口盖 radiator filter cap压力式水箱盖 radiator-pressure cap蒸气-空气泄放阀 vapor-air release valve散热器护罩 radiator cowl散热器百叶窗 radiator shutter散热器保温帘 radiator roller blind散热片 cooling fin缸盖散热片 cylinder head fin缸体散热片 cylinder block fin控温装置 temperature regulating device恒温器 thermostat恒温器主阀 thermostat main valve恒温器旁通阀 thermostat by-pass valve恒温器挠性波纹筒 thermostat flexible bellows液体冷却设备 liquid cooling equipment水泵 water pump水泵体 pump casing水泵叶轮 water pump impeller旁通进水口 water by-pass inlet neck循环泵 circulating pump主进水口 water main inlet port出水口 water outlet port自调式水封 self-adjusting seal unit溢流管 overflow pipe导流板 deflector风扇 fan(blower)轴流式风扇 axial flow fan离心式风扇 centrifugal fan风扇壳体 blower casing风扇导流罩 fan cowl风扇毂 fan hub风扇叶片 fan blade风扇叶轮 blower impeller风扇导流定子 blower stator风扇皮带轮 fan pulley三角皮带 v-belt风扇护罩 fan shroud风扇叶轮叶片 impeller vane冷却用空气 cooling air风扇导流叶片 stator vane强制风冷 forced-air cooling自然风冷 natural air cooling风道 air ducting润滑系 lubrication system润滑 lubrication气缸上部润滑 upper cylinder lubrication 压力润滑 pressure-feed lubrication压力润滑法 forced lubrication自动润滑 automatic lubrication飞溅润滑 splash lubrication润滑周期 lubrication interval边界润滑 borderline lubrication曲轴箱机油油盘 crankcase oil pan油底壳 oil pan机油盘放油塞 sump plug集油器 oil collector机油泵 oil pump计量式机油泵 metering oil pump齿轮式机油泵 gear type oil pump转子式机油泵 rotor-type oil pump机油泵出油管 oil pump outlet pipe放油口 oil drain hole油道 oil duct断油开关 cut-off cock机油散热器 oil cooler机油滤清器 oil filter机油粗滤器 primary oil filter机油精滤器 secondary oil filter全流式机油滤清器 full-flow oil filter分流式机油滤清器 by-pass oil filter离心式机油滤清器 centrifugal oil filter整体式滤芯 integral filtering element细滤器滤芯 filter element滤清器壳 filter box滤片filtering disc机油减压器 oil pressure relief valve旁通阀 by-pass oil filter机油滤网 oil strainer加机油孔 oil filter cap滤芯轴 filter shaft刮片组件 cleaning edge机油量尺 dipstick机油滤网 oil strainer增压器 supercharger增压和扫气装置 pressure-charging and scavenging unit 增压装置 supercharging device涡轮增压器 turbo-charger气波增压器 comprex pressure wave supercharger增压器阻风阀 supercharger blast gate增压器调节容气量的旁通阀 supercharger control bypass 增压器叶轮 supercharger impeller惯性增压 inertia supercharging机械增压 mechanical supercharging涡轮增压 turbo-charging增压比 supercharge ratio增压压力 boost pressure增压中冷 inter-cooling中冷度 inter-cooling level增压度 supercharging level喘振 surge喘振线 surge line轴流式涡轮 axial-flow turbine脉冲进气 ram charging发动机试验 engine test发动机试验规程 engine test procedure发动机技术要求 engine technical requirements标准大气状况 standard atmospheric conditions大气压力 atmospheric pressure进气温度 inlet air temperature进气温度 inlet air temperature功率校正 power correction功率标定 power rating功率换算 power conversion校正系数 correction factor换算系数 performance test性能试验 performance test起动性能试验 starting ability test怠速试验 idle running test道路负荷试验 road load test各缸工作均匀性试验 cylinder variation test背压试验 back pressure test最低稳定工作转速试验 lowest continuous speed test with load 背部泄漏试验 back-leakage test调整试验 adjustment test热平衡试验 heat balance test快速磨损试验 accelerated wear test热冲击试验 thermo-shock test空载特性试验 no-load characteristic test模拟增压试验 simulated supercharging test停缸试验 cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验 exhaust analysis test突变负荷试验 sudden load change test稳定性试验 stability test单缸熄火试验 one cylinder shut off test例行检查试验 routine inspection test验证试验 verification test鉴定试验 approval test可靠性试验 reliability test耐久性试验 durability test定型试验 type approval test验收试验 acceptance test现场试验 field test出厂试验 delivery test抽查试验 spot check test复查试验 re-check test台架试验 bench test强化试验 hop-up test发动机试验台 engine test bed底盘测功机 chassis dynamometer测功机 dynamometer水力测功机 hydraulic dynamometer电涡流测功机 eddy current dynamometer电力测功机 electric dynamometer扭矩仪 torque meter转速表 tachometer温度测量 thermometry温度测量仪器 thermometric instruments空气流量测量 air flow measurement热线风速仪 hot wire anemometer电子示功仪 electronic indicator燃烧分析仪 combustion analyzer压力传感器 pressure transducer精密声级计 precision sound level meter排放 emission排放物 emission排气污染物 gaseous pollutant蒸发排放物 evaporative emission曲轴箱排放物 crankcase emission漏气 blowby gas氨氧化物 oxids of nitrogen一气化碳 carbon monoxide碳氢化合物 hydrocarbon甲烷 methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物 photochemically reactive hydrocarbons 微粒物 particulated matter黑烟 black smoke蓝烟 blue smoke白烟 white smoke碳烟 soot光化学烟雾smog臭味 odor丙烷 propane排放浓度 concentration of emission排气烟度 exhaust smoke先期排气 initial exhaust亚临界排气 subcritical exhaust超临界排气 supercritical exhaust强制排气 forced exhaust自由排气 free exhaust排气提前角 exhaust advance angle排气迟后角 exhaust lag angle排气热损失 exhaust heat loss排气净化 exhaust purification排气背压 exhaust back pressure残余废气 residual gas排气有害成分 poisonous exhaust composition柴油机排烟 diesel smoke综合排放浓度 composite concentration of exhaust emission 综合排放质量 composite mass of exhaust emission排放系数 emission factor排放率emission index质量排放量 mass emission比排放量 brake specific emission排放物控制系统 emission control system排气排放物控制系统 exhaust emission control system二次空气 secondary air二次空气分配歧管 secondary air distribution二次空气控制阀 secondary air control valve二次空气转换阀 secondary air switching valve二次空气转流阀 secondary air diverter valve二次空气喷射装置 secondary air injection system二次空气喷射管 secondary air injection tube二次空气喷射减速压阀 secondary air injection relief valve 脉动空气装置 pulsating air system二次空气泵 secondary air pump曲轴箱排放物控制系统 crankcase emission control system曲轴箱双通风系统 crankcase closed system曲轴箱单通风系统 crankcase sealed system曲轴箱强制通风装置 positive crankcase ventilationPCV阀 PCV valve蒸发排放物控制系统 evaporative emission control system活性碳罐贮存装置 charcoal canister storage system活性碳罐 charcoal canister曲轴箱贮存装置 crankcase storage system空气滤清器贮存装置 air filter storage system燃油箱止回阀 fuel tank check valve油气分离器 fuel and vapor separator清除阀 furge valve催化转化系统 catalytic converting system催化燃烧分析仪 catalytic combustion analyzer催化剂 catalyst转化器 converter催化转化器 catalytic converter轴流式转化器 AXIAL FLOW TYPE CONVERTER径流式转化器 RADIAL FLOW TYPE CONVERTER下流式转化器 down flow type converter上流式转化器 up flow type converter双床式转化器 dual bed converter单床式转化器 single bed converter氧化型催化剂 oxidation catalyst还原型催化剂 reduction catalyst三元催化剂 three-way catalyst贵金属催化剂 noble metal catalyst。

发动机的一些名词解释英文

发动机的一些名词解释英文发动机是现代汽车的核心设备之一，负责产生动力并驱动车辆运行。

了解发动机中的一些常见名词及其英文对应，有助于我们更好地理解和使用汽车。

本文将介绍发动机中的一些关键名词，并提供相应的英文解释。

1. 气缸（Cylinder）汽车发动机通常由多个气缸组成，每个气缸内都有一个活塞。

气缸是发动机燃烧室的一部分，用于容纳和压缩空气和燃料混合物，产生爆炸力来驱动活塞运动。

在发动机规模确定后，气缸的数量是一个关键参数。

2. 活塞（Piston）活塞是位于气缸内的一个圆柱形部件，负责产生往复运动。

活塞通过连接杆与曲轴相连，曲轴将活塞的直线运动转换为旋转运动，从而提供动力给汽车。

3. 曲轴（Crankshaft）曲轴是发动机中一个非常重要的部件，它将活塞的往复运动转换为连续的旋转运动。

曲轴能够将发动机的高速旋转动力输出到传动系统，驱动车辆行驶。

曲轴的工作原理可以视为一个平衡的重锤，可以抵消活塞产生的晃动力。

4. 燃烧室（Combustion chamber）发动机的燃烧室是气缸的一部分，用于容纳空气和燃料混合物的燃烧。

燃烧室的设计直接影响发动机的功率、燃烧效率和排放水平。

5. 点火系统（Ignition system）点火系统用于点燃气缸内的混合物，引起爆炸，从而推动活塞的运动。

点火系统中的重要组件包括点火线圈、火花塞和点火控制单元。

6. 进气歧管（Intake manifold）进气歧管是连接发动机气缸与空气滤清器之间的部件，用于输送空气和燃料混合物到燃烧室。

进气歧管的设计对发动机性能有着重要影响，如进气效率和动力输出。

7. 排气歧管（Exhaust manifold）排气歧管与进气歧管相对应，负责将燃烧产生的废气从燃烧室排出。

排气歧管的设计也会影响发动机效能，如排气效率和噪音水平。

8. 涡轮增压（Turbocharging）涡轮增压是一种提高发动机功率和扭矩输出的技术。

通过安装涡轮增压器，增加进气歧管中的压力，从而提高燃烧效率，实现更高的动力输出。

发动机中英文术语

汽车发动机专业术语

发动机性能术语 英汉对照

汽车发动机相关中英文对照

发动机专业英语词汇.

发动机中英文术语

(整理)发动机专业英语单词.

发动机专业英语词汇

航空发动机常用汉英词汇.

航空发动机常用汉英词汇

发动机专业英语单词

发动机英语

(整理)发动机相关中英文对照

航空发动机常用汉英词汇

发动机中英文术语

发动机的一些名词解释英文

发动机性能术语英汉对照