cita词汇

脱胎off jig 横梁beam 纵桁girder 面板face plate 对接缝butt weld 角焊缝fillet weld 对称焊symmetrical weld 搭焊overlapping weld 分段退焊法step weld 缓焊=后焊舱壁扶强材/结构加强筋stiffener 驾驶室顶柱灯masthead lantern 超速停车overspeed shutdown吊环lifting lug 垂直度squareness 防火风闸fire damper 火工hot work 拼接，拼装splicing装配assembly 坡口groove 对角线diagonal line 毛刺burr 去毛刺deburring艉管滑油stern tube lube oil 磁粉探伤magnetic inspection 丝米decimillimetre 灰罐dry bulk tank微米micron 舵从中间位置向右舷偏转10度并保持不变，直到船的航线偏离原航线至右舷10度The rudder is turned from its neutral position to 10°starboard, and held until the course of the vessel changes an angle of 10°starboard to the original course. 通经ND (norminal diameter) 外径OD 磷化处理phosphated 实习轮机员apprentice engineer 实习驾驶员apprentice officer 电助assistant eletrical engineer 轮助assistant engineer 驾助assistant officer A.B.L=above base line 距基线报助assistant radio officer 水手长boatswian/bosun 见习生cadet 船长captain/master 副水手长cassab 报务主任chief radioofficer 轮机长chief engineer 大副chief officer 事务长chief steward 舵工/艇长coxswain 吊臂托架jib rest post 钢索套环thimble 压紧器装置snap lock assembly 端部止动装置end stopper assembly组合件assembly 支承块support plate 压紧扁钢compression FB 排水阀check valve 撬棒handspike方钢square bar 止动板stopper plate 开坡口be chamfered 机架stand post 立柱column 撇缆heaving line 翻梯装置rotatable davit 绑扎孔lashing hole 吊梯索wire rope 轻压载水线light ballast water line 声光信号布置图arr. Of mast rigging and signal 电笛ele. Whistle 汽笛air whistle 锚钟anchor bell 旗钩flag hook 信号索滑车block for engine rope 墨球black ball 前桅灯fore masthead light 横档bar 防磨材fender 羊角cleat 救生索life line 带自亮浮灯with self-ignating light 救生服immersion suit 抛绳装置lifeline throwing appliance 火箭降落伞烟火信号rocket parachute flare 消防员装备储存箱fireman’s outfitting 水龙带箱fire hose box 紧急逃生呼吸器emergency escape breathing device 干粉灭火器dry powder fire ex. 安全斧fire axe 带抓钩和消防绳的腰带belt with snaphook and lifeline 通导设备间com. & nav. Equipment 满焊full weld 吊舵lifting rudder 眼板eye plate 车叶propeller 垫板mat plate 钢丝夹头steel wire collet 水煤气管G.S.P water & gas pipe 螺旋扣turnbuckle 拉索pulling wire 抽风机exhaust fan 通风栅grille 六角螺栓hex screw 弹簧垫圈spring washer 可调楔块adjustable chock 环氧垫片epoxide chock 双面连续焊double continuous welding 三角板：bracket 最大允许径向跳动和端面跳动为0.10MM The maximum allowable radio run out and axial run out is normaly 0.10MM.对舱壁板横向加排（球钢）Add “BF” on the bulkhead plate 倒角=将角切除衬板lining 风暴盖storm cover 对舱壁进行火工矫正，并将矫正后壁板与加排点焊固定支架shelf 舷外标志hull markingAdjust the plates, and then weld them with “BF” by button-spot weld. U.N.O=unless noted otherwise 除非另有说明辅机操作工donkeyman 电机员electrical engineer 舵手helmsman 机工motorman 舵工quartermaster 大管轮second engineer 二副second officer 定员complement 物料管理员store keeper 额外人员supernumerary 沉头螺钉flat-head screw 橡胶垫rubber band 花钢板floor plate HV AC RM 烟囱栅架funnel grid扁钢flat steel 调试commissioning 回油管return pipe 泄放阀bleed valve 本锻件完成后应进行正火回火处理the forging should be normalized and tempered 残余元素residual element 屈服强度yield strength 抗拉强度tensile strength 断面收缩率shrinkage of section 冲击能量charpy 磁粉探伤magnetic detection超声波探伤ultrasonic test 干涉配合interference fit 塞龙thorden 调质处理normalized & tempered 不同心度non-concentricity 调整垫片安装拂配后的色油检查，其接触斑点应分布均匀，接触面应大于70%Paint color oil on the treated adjustment pad. The contact point should be distributed uniformly. The contact area should be larger then 70%. 舵机安装螺栓紧固力矩rudder setting tightening torque 扁螺母lock nut 铰质螺栓fit bolt 活动垫铁flexible steel pad 铰孔ream 无卤halogen free 阻燃型low smoke&zero helogen=LSZH导缆器fairlead 现场拉线running a line at site 羊角滚轮cleat roller 底座高度应予留足切割余量The seat need to have enough remainder for cutting.眼环lash eye 十字带缆桩cross bitt 流水管drain pipe 导缆孔座seat of panama chock 环氧树脂垫块epoxy chock 刹车支持负载break capacity 抓斗平台grab rest/platform 腹板web 垫板gasket 肘板bracket 筋板stiffener 回转角度slewing angle 功率output 横倾heel 纵倾trim 格栅架jib rest变幅时间luffing time 拧紧力pretension force 吊钩固定hook lashing 铰链gemel 二管轮third engineer电线工wireman 工种trade 钳工bench work 气焊工burner 凤铲工/缺陷修整工chipper 起重工crane operator 电镀工eletroplater 领班foreman 勤杂工janitorial 安装工joiner 细木工joinery 放样工loftsman 机修工mechanic 造型工moulder 作业长operation head 木模工patternmaker 索具装配工rigger钣金工/冷作工sheet metal work 装配工fitter 定位搭焊工tacker 定期货船cargo liner插座socket 发电机加热控制变压器transformer of DG heater controller 扬声器public address 火警探头fire detector 电工实验板electrical test panel 电源滤波器power filter 加强筋stiffener 泵筒附内芯pump barrel with plunger 泵壳pump housing 泵柱pump roller 切割工具cut off device 扳手spanner 管钳socket wrench 24球柄把手24 racket handel 轻柴油试验MGD 失电试验black out 电子海图辅助显示单元ECDIS LCD MONITOR 分配放大器distribution amplifier 接地板earth plate X波段雷达X-band radar 风速风向仪anemometer 解码器encoder 登船梯embarkation ladder 推车式灭火器wheeled fire extinguisher 橡胶圈rubber gasket 扶手hand support 柴油/轻柴增压模块机械密封泵MDO/MGO booster module mechanical seal pump变速箱gear box 燃油站bunker station 实习生cadet 油吊bunker crane 抛落艇吊艇架free fall davit冷库chiller box 彻底检查overhaul 液位计level gauge 肘板bracket 冷却水舱CWT 围栏cofferdam主配电板MSB 流量机Flowmeter 上部结构overstructure 进水报警water ingress alarm system UT=ultrasonic 注油泵filling pump 舵角rudder angle 转换面板change over panel 过桥cross 防滑漆anti-skid paint电磁阀solenoid valve 混油桶mixing tube 移货绞车tugger winch 消油剂oil dispesant 防水层watertight layer扶强材stiffener 衬板liner 踢脚板skirting plate 甲板敷料deck covering 隔声绝缘acoustic insulation拦水扁铁gutter bar 防滑地砖anti-slip tile 硅胶silicon 粘合剂adhesive 珍珠岩混凝土perlite concrete底座support 岩棉rock wool 综合屏蔽collective screen 驾控前台bridge control console forword复示器repeater panel 主显示器central unit 荧光舱顶灯fluorescent pendant light 荧光蓬顶灯fluorescent ceiling l. 双报双联开关two connection switch 荧光灯调光开关fluorescent light dimmer 投光灯flooding light启动空气减压阀starting air check valve 紫外线杀菌装置ultraviolet purifier 白炽舱顶灯incandescent pendant light 分电箱distribution panel 逃口ESC. 救生用品间safety locker 接线盒junction box 失电报警信号power lose alarm 自动舵autopilot 车床基座lathe foundation 砂轮机grinding machine 钻床基座drill foundation钳工桌work desk 顶板top plate 平面度flatness 扭曲度distortion degree 围壁开孔wall opening 错位misalignment 甲板敷料deck covering 畅通试验free flowing 锅炉给水boiler feed water 汽缸油cyl. Oil 探伤PT test 冷装配shrink fitting 轴系三线校中alignment of shafting three lines 柴油日用舱M.D,O service tank舵叶止跳块间隙测量measuring clearance of rudder blade jumping stopper 加热盘管heating coil 氧乙炔管系oxy-acetylene piping 镗孔前before boring 艉绞车液压管系aft. Winch hydraulic piping 串油oil flushing阴极保护电缆ICCP cable piping 气控百叶窗管air control window shutter piping 艉轴propeller shaft舵机止推块拂配blue-fitting of S/G stopper 低位海水箱low sea chest 主机滑油循环舱M/E L.O. SUMP TK.顶升负荷jack up load 拐档差crankshaft deflection 主机挠度测量M/E deflection 减震器压缩量compression of G/E shock absorber 地脚螺栓hold-down bolts 飞轮法兰flywheel flange 环氧浇注前before epoxy环氧浇注chockfast 拉线照光alignment of shaftline and rudder line 艉管定位检查center line of S/T 舷外管加强肘板焊前overboard pipe deep bracket B/W 热油总管thermal oil main pipe 锌块zinc slab 超压试验pressure test环氧硬度hardness of S/T epoxy 螺旋风管spiral duct 艉轴承间隙clearance between propeller shaft and bearing 艉轴下沉量wear-down of propeller shaft 塞龙尺寸测量dimension of thorden bush 报警点alarm point止推块蓝配blue-fitting of S/G stopper 主机下空仓M/E cofferdam 抛艇液压管freefall boat hydraulic pipe肿部吃水阀midship draft valve system 集控室浮动地板绝缘检查ECR floating floor 艉密封对中alignment of aft sealing device 上建汽笛管系air horn on SST 增压器supercharger 油底壳oil pan 上建杂用空气系统domestic air piping on superstructure 主机修正轴系顶升试验M/E shafting jack up load after epoxy 海水管sea water piping 透气孔air hole 锚链anchor chain 天线柱antenna pole 减摇水仓anti-rolling water tank 轴系shafting 舱室舾装cabin outfitting 舵叶rudder blade 偏差deviation 铰孔螺栓reaming bolt 螺栓孔圆柱度cylindricity of bolt hole 过盈量oversize 塞尺feeler 舵销pintle 锥体部分taper part 不锈钢衬套stainless steel sleeve舵钮gudgeon 酚醛树脂衬套phenol resin bush 舵柄tiller 与键的过盈量oversize with key 舵承rudder carrier 摩擦片接触面friction disc 垫块接触面contact ratio of chock liner 机对中steering gear alignment 轴系拉线alignment of shafting 粗糙度roughness 艉轴轴承的装配压入force fitting of tail shaft 接合面connection surface 艉轴锥面tail shaft cone surface 螺旋桨锥孔propeller tape hole 色油点color oil point 误差tolerance主机垫片M/E chock 浇注casting 底脚螺栓holding down bolt 曲轴甩挡crankshaft deflection 运转试验running t 垫块liner 基座base 可垫薄片shim plate 甲板行车deck travelling crane 导轨rail 门架型gantry type弯管bent pipe 支管branch pipe 贯通件penetration pipe 铜焊brass brazing 黄铜管al-brass pipe套管socket 椭圆度ellipticity 弯曲半径curvature radius 管子弯曲起皱和降起bending rumples and swells铜管copper pipe 异径reducer 管子边势准备edge preparation 封底焊接back bead 咬口undercut塑料夹具plastic clamp 惰性气体inert gas 管子护圈pipe coaming 落地插座floor plug 天线插座antenna p.蜂鸣器buzzer 侧移式side rolling type 对角线偏差diagonal difference 垂直挠曲度vertical deflection密封槽packing gutter/groove 压紧条compression bar 方趸型pontoon type 燃料舱bunker 船舱/房间cabin斜横梁cant beam 斜肋骨cant frame 绞盘capstan 狭窄的舷梯catwalk 中内龙骨center keelson隔离舱cofferdam tank 防撞舱壁collision bulkhead 舷梯companion ladder/gangway 槽型舱舭板corrugated bulkhead plating 航向记录仪course recorder 船员住所crew’s quarters 桅上瞭望台crow’s nest 暗室dark chamber 横梁beam 纵桁girder 纵骨longitudinal 甲板边板deck stringer 扫舱泵stripping pump 化学药剂柜Chemical dosing tk.盐水系统brine system 日用水系统hydrophone system 软管接头hose coupling valve 球阀ball valve止回阀non-return valve 盲板阀blind flange valve 压力传感器pressure transmitter 双联滤器duplex filter螺杆泵screw pump 泄油盘drip pan 水位自动控制automatic level control 绝缘电阻insulation resistance低硫柴油LSDO 转换试验changeover test 充气试验air charging test 分油机purifier 柴油MDO重油HFO 烟气风机flue gas fan 起跳压力relieving pressure 抽吸试验suction test 总用泵G.S.pump含油浓度模拟试验simulation oil content test 漏斗带盖funnel with cover 膨胀水箱expansion tank调节阀balancing valve L型艉推L-drive 干货空压dry bulk air compressor 变频器frequency converter线性电抗器line reactor 就地按钮local push button 船舶监测系统VMS 工字梁cross beam 挡货栏杆cargo rail 坡口groove 直通截止阀stop valve 通海阀sea valve 板式止回阀plate check valve 根阀root valve铸钢cast steel 铸铁cast iron 膨胀节expansion joint 温度计thermometer 喷淋头spray国际通岸接头international shore connector 单联滤器simplex filter 真空压力表及旋塞compound gauge with cock压力表pressure gauge 冲洗管flushing pipe 驾驶甲板bridge deck 油渣泄放口sludge outlet 液位开关level switch 垫片特力tesnit 凹槽recess 投油oil flushing 衬套sleeve 轴套bush 吊装眼板lifting eye 钢制搁架steel shelf 深肋板deep floor 深肋骨deep frame 吊杆derrick 侧向仪天线direction finder antenna 坞墩dock block值班船员餐厅duty mess 应急出口escape trunk 流线型板fashion plate 音响测深仪fathometer 减摇鳍fin stabilizer 灭火水龙带fire hose 折边flanged edge 舱口盖锁紧装置flip-flop 首垂线fore perpendicular前桅foremast 顺流fair current 逆流counter current 全速前进full speed ahead 锚机试验anchor and windlass 物料吊provision crane 液压回转软管吊hydraulic slewing crane 淤泥吊sludge handling davit舵角零位校准perform the calibration of rudder with angle at 0°。