诺基亚设备告警代码的含义翻译

合集下载

常用告警说明(诺西)

序号 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
29 36 39 28 30
告警 VSWR minor alarm(1838) Failure in optical RP3 interface(3030) Configuration error: Not enough HW for LCR(3070) Connection lost Failure in replaceable baseband unit(3003) VSWR alarm(1837) Baseband bus failure(3020) RF module failure(3010) System module failure(3000) Temperature alarm(3040) Fan failure(3050) Fan failure during fan test(3050) BTS reference clock missing(3080) BTS reset required(4001) Failure In Optical Interface 1(3012) Failure In Optical Interface 0(3012) BTS is uncommissioned(4030) Incompatible SW version detected Commissioning error: Invalid Configuration file(3060) SW fallback(4082) Transport layer connection failure in S1 interface(6202) VSWR major alarm(1837) TX failure in MIMO(4003) BTS master clock tuning failure(1818) BTS synchronization is missing during startup(4160) BTS time not corrected Cell configuration data distribution failed(6253) Error in file server during SW download GPS Receiver alarm: Control Interface not available(4011) GPS Receiver alarm: EEPROM segments status(4126) NE disconnected before upload finished PPS reference clock missing in startup(4153) S1 interface setup failure(6308) Configuration error: Unit initialization failure(3070) Firmware SW mismatch(2056) Parallel RP3-01 link length mismatch(4072) TD-SCDMA minor alarm(4179) BTS internal SW management problem(3090) Cell power failure(4090) Configuration error: Unknown HW resource(3070) RF Loss of secondary optical interface(1930) System module failure F Failure In Optical Interface RRU optical/eletrical module absence 1(3012) RF BB bus connection transmission error(1906) Validation of signed file failed(4145) Failure in optical RP3 interface Unit blocked High memory consumption(6502) Failure In Optical Interface Abnormal CPRI interface to next hop 1(3012) 1935转速高 1932、33风扇坏

NOKIA基站告警代码详细解析

7960 7961 7962 7963 7968 7969 7971 7972 7973 7974 7975 7976 7990 7991 7995 7996 7997 7998 7999 8000 8020 8048 8050 8066 8081 8086 8096 8099 8102 8112 8125 8141 8159 8179
7590 7600 7601 7602 7603 7604 7606 7607 7608 7609 7615 7616 7620 7622 7700 7701 7702 7704 7705 7706 7711 7712 7714 7715 7716 7719 7722 7723 7724 7725 7728 7729 7730
** * ** ** ** *** *** * * * * * * * * * * * * * * * * ** *** ** * * ** * ** *
7128 7129 7132 7139 7157 7159 7160 7161 7162 7163 7164 7172 7177 7190 7193 7194 7195 7198 7199 7200 7201 7203 7204 7208 7209 7210 7211 7220 7221 7251 7255 7256 7257 7260 7262
7834 7835 7836 7838 7839 7840 7841 7842 7860 7863 7870 7872 7873 7874 7879 7882 7890 7900 7939 7941 7942 7943 7944 7945 7946 7947 7948 7949 7950 7952 7953 7954 7955 7956
*** ** ** ** ** ** ** *** ** * * *** *** ** ** *** * *** ** ** *** ** ** ** ** ** ** ** *** ** ** *** *** ***

诺基亚核心告警汇总

NOKiA 常见告警列表1252--数据连接错误率过多--EXCESSIVE ERROR RATE ON DATA LINK CONNECTION--不通知1569--安全报告达到临界极限--CRITICAL LIMIT IN SECURITY REPORTING REACHED--不通知2007--文件更新到备份储存器失败--FILE UPDATING ON AUXILIARY STORAGE IS NOT PROCEEDIN--通知（用DUQ查询是否更新成功，0为正常）2015-- MB单元通讯错误--MB COMMUNICATION ERROR--通知2017--文件分配错误--FILE DISTRIBUTION ERROR--不通知2018--标志池满--DYNAMIC FLAGPOOL FULL--如果附加信息为告警号0003、0004、0026、0691、0860、1001、1007、1014、1016、1020、1023、1024、1071、1072、1078、1559，1571、1645、1677、1860引起的告警，立即通知话务室，其他不通知（由附加信息第一项的告警产生过多引起，一般不会自动消失，需手动清除）2039--ET时钟失败--ET CLOCK FAILURE--通知2054--CHECKSUM ERROR IN BOOT PROM--通知2055--VANG FAILURE--通知2056--CHECKSUM ERROR IN VANG SAMPLE--不通知2064--ROUTE SEA无效--ROUTE SET UMAVAILABIE--通知---用NRI指令查看路由状态，正常状态为AV-EX或AV-SP2068--文件分配失败--FILE DISTRIBUTION FAILURE2069--信令检验失败--SIGNALLING LINK TEST FAILED--通知（一般由传输环路引起）---用NEL指令查LINK状态2070--LINK SET异常--LINK SET UNAVAILABLE--通知---用NSI指令查看状态，正常状态为AV2072--LINK激活或恢复失败--FAILURE IN SIGNALLING LINK ACTIVATION OR RESTORATION--通知---用NEL指令查LINK状态2099--不成功的呼叫率超过门限—忙时需重视（白天很重要，发单）——TUT：SER查询未接通率2122--多功能缺少--MULTIFRAE MISSING--不通知2123--REMOTE END MULTIFRAME MISSING--不通知2130—CCS电路错误状态CCS CIRCUIT IN FAILURE STA TE--不通知2137--插件单元位置错误--PLUG-IN UNIT LOCATION ERROR--通知2138--软件包插件单元校验错误--PLUG-IN UNIT SOFTWARE PACKAGE CHECK SUM ERROR--通知2139--软件包插件单元装载失败--OFTWARE PACKAGE LOAD FAILURE--通知2153--CIRCUIT RELEASING FAILED IN CAS--不通知2160--预处理单元重启失败--PREPROCESSOR UNIT RESTART FAILURE--通知2163--线路信号反常--ABNORMAL LINE SIGNAL RECEIVED --不通知2184--OSI CLNS MANAGEMENT INFORMA TION CORRUPTED--不通知2186--不通知2185--路由操作失败--ROUTING OF OSI OUTGOING CALL FAILED--不通知2205--传输告警--ET2 FAILURE--不通知（个别时隙不好）2224--ERROR IN MSU HANDLING--不通知2227--事件日志保留错误--EVENT LOG SAVING ERROR--不通知2234--计费文件缓存器已满--HOT BILLING RAM-BUFFER IS FILLING UP--不通知2241--SCCP子系统被禁止--SCCP SUBSYSTEM PROHIBITED--通知---用NHI查看子系统状态，正常状态为AV-EX2246--SCCP路由失败--SCCP ROUTING FAILURE--不通知2247--信令消息错误--SS7 ERRONEOUS SIGNALLING MESSAGE--不通知2250--D信道激活或恢复失败--FAILURE IN D-CHANNEL ACTIVATION OR RESTORATION--通知（附加信息最后一位是ET号）ZDTF：ET，ET号；2252--主要存取终端上的循环测试失败--LOOP TEST FAILED IN PRIMARY RATE ACCESS TERMINAL--通知2254--网络中的SCCP没有定义--SCCP NOT DEFINED FOR NETWORK--不通知2259--数据库不一致--DATABASE IS INCONSISTE NT--通知，发单2262--OSI子系统界面状态不好--OSI SUBNETWORK INTERFACE OUT OF ORDER--不通知（一般伴随3053告警，大量闪断时通知，重要时需发单）2269--错误的磁盘缓存尺寸--ERRONEOUS DISK CACHE SIZE--通知2272--BOOT LOADING ERROR2274--SOMAFI文件错误--SOMAFI ERROR--通知（SOMFI文件很重要）2381--空闲存储空间减少--AMOUNT OF FREE MEMORY CRITICALLY REDUCED 2386—VDS设备数据文件写入过多而无法转移--OVERWRITING UNTRANSFERREDVDS-DEVICE DATA FILE--不通知2390--时钟外同步信号丢失--EXTERNAL CLOCK SYNCHRONIZATION SIGNAL MISSING--不通知2393--FALLBACK COPYING TERMINATED IN ERROR--通知（ZZ所有HLR通知）2397—数据库文件将满--DATABASE FILE IS IN DANGER TO GET FULL--通知,发单2398--订户操作被阻止--SUBSCRIBER HANDLING BATCH JOB INTERRUPTED--不通知2399--数据库无法更新--DATABASE DISK UPDATES ARE PREVENTED--通知2402--AFS板连接故障--AFS CONNECTION FAILURE--通知2403--连续的信道错误--SERIAL CHANNEL FAILURE--通知2410--A口电路连接失败--CONNECTION OF A CIRCUIT HAS FAILED IN THE SWITCHING NETWORK2424--记录数据和位图内容不一致--DISCREPANCY BETWEEN RECORD DATA AND BITMAP----不通知2439--MSC和短信中心无连接--NO LINK BETWEEN MSC AND SMSC--通知并发单（MSC至SMSC断连，会影响短信收发，重要告警）2445--单元类型无冗余--UNIT TYPE HAS NO REDUNDANCY--通知2449--MSRN操作错误--MSRN HANDLING ERROR--2494—MSRN保留率--MSRN RESERVATION RATIO—立刻通知2503--计费丢失--DETAILED CHARGING LOST--2504--计费文件满--CHARGING FILE FILLING UP—2518--系统备份未完成--NO VALID FALLBACK COPY FOR DEFAULT RACKAGE--通知对端备份---用WQO：CR；查软件包状态，看FB包时间是否是最新2525--计费数据存储失败--FAILURE IN STORING OF DETAILED CHARGING DATA--2532--网络适配器丢失--ANALYSIS FOR NETWORK GENRATED NBR OR FOR CHA CASE IS MISSING--不通知2533--路由数字丢失--ROUTING NUMBER MISSING FROM RZN TABLE--通知2536--VLR上用户数据满--SUBSCRIBER DATABASE FILE IN VLR IS FULL--2547--调制解调器错误--MODEM FAILURE--2549--不可用的VDS存储器数据文件达到首要告警界限--FIRST ALARM LIMIT FOR UNAVAILABLE VDS-DEVICE DATA FILES REACHED--通知---用IFO:CHU:GSMCHA:，FULL；查询---用IFS:CHO:GSMCHA:号码&&号码：T；改状态ZIFS：STU：GSMCHA：3,TRANS,：T：；2550--不可用的VDS存储器数据文件达到第二告警界限--SECOND ALARM LIMIT FOR UNAVAILABLE VDS-DEVICE DATA FILES REACHED2551--可用的VDS存储器数据文件溢出--OUT OF AVAILABLE VDS-DEVICE DATA FILES 2558--回声抑制器连接失败--ECHO CANCELLER CONNECTION FAILURE-- （附加信息第一位为ET号）2559--数据访问出错--DATA CALL ERROR RATIO EXCEEDED-不通知2562--NUMBER NOT FOUND FROM HRNFIL OR INVALID DATA--通知(一般由于单元重启引起，可能不会自动消失，需手动清除)2568--ERROR IN GSAPRB ANALYSIS FILE--通知2590--ERROR IN OPENING OUTPUT FILE--通知2595--时隙失败--EC/IWF TIME SLOT FAILURE--不通知2596--SCCP登记错误--SCCP REGISTRATION ERROR--通知2618--计数器更新错误--UPDATING ERROR OF ACCOUNTING COUNTERS--附加信息第二项为FFFFFFFF第五项为 9999d的不用通知，若出现其他信息则需通知2621--时隙测试失败--FAULTY TIME SLOT IN TESTING OF TIME SLOT BASED UNIT--不通知2632--时钟震荡器故障--OSCILLATOR FAILURE--通知2638--同步单元故障--FAILURE IN BUS BETWEEN SYNCHRONIZATION UNITS --通知2639--FAILURE IN SYNCHRONIZATION UNIT SWITCHOVER--通知2641--同步输入信号失败--FAILURE IN SYNCHRONIZATION SIGNAL--通知，需发单（若为传输引起，查询传输不会显示局向）---用DRI查询看哪个2M不好（TUT：SER查呼叫失败率，20％为正常）2646--路由协议失败--PROTOCOL ROUTING FAILURE--不通知2650--硬盘数据存储失败--STORING OF THE DATA FAILED ON ONE DISK--通知2651--双方硬盘数据存储失败--STORING OF THE DATA FAILED ON BOTH DISKS--通知2653--管理文件操作失败--FAILURE IN THE HANDLING OF CONTROL FILES--不通知2654--核心网触发键无服务包--NO SERVICE PACKAGE FOR CORE INAP TRIGGER KEY--通知（该告警的出现是因为对端HLR中参数所引起，当用户漫游到河南时，用户数据里插入的有SSET参数，河南的SSET参数为20，当双方不一致时候产生该告警）2658--第二路由的计费数字丢失--CHARGED NUMBER FOU THE SECOND LEG OFREROUTING IS MISSING—根据附加信息是否通知一般不用处理2659--ERROR IN POOL CONTROLLER MESSAGE TRAFFIC--不通知2661--硬盘数据库拷贝不一致--NO CONSISTENT COPY OF DATABASE ON DISK--不通知2663--数据管理器堆积错误--DUMPING ERROR IN DATABASE MANAGER--不通知2664--同一硬盘数据库拷贝停留在不一致状态--DATABASE COPY STAYS INCONSISTENT ON SAME DISK--通知2666--数据更新停留在活动单元--DBSMAN STOPPED IN ACTIVE UNIT--不通知2668--呼叫建立失败--CALL ESTABL IS HMENT FALLURE----不通知2671--数据服务单元不可用--DATA SERVICE UNIT IS NOT AVAILABLE--通知2673--MAXIMUM NUMBER OF EX ECUTED DIGIT A NALYSIS EXCEEDED--不通知2683--MML命令日志访问错误--ERROR IN MML COMMAND LOG ACCESS--通知2692--相关单元或I/O设备工作状态异常--INCORRECT WORKING STATE--通知（CTU和FDU单元不用处理）---用USI查单元状态，在变为测试状态时系统会自动诊断，用UDH查诊断结果，结果为3999表示已通过，若状态仍未恢复，则需手动恢复2693--WO-EX单元错误--WO-EX UNIT FAULTY-通知2733--NO FREE RING DISK FILE--不通知2734--事件缓冲器溢出--EVENT BUFFER OVERFLOW--通知2735--事件缓冲器溢出--EVENT BUFFER OVERFLOW--通知2737--回声道删除失败--ECHO CANCELLER CHANNEL FAILURE--通知2740--呼叫指数保留有过多干扰--EXCESSIVE DISTURBANCES IN CALL INDEX RESERVATION2742--BSC退出服务--BSC/MGW(REL99) OUT OF SERVICE IN MSC--通知2744--MSC上的BSC或BTS状态错误--BSC/MGW(REL99) OR BTS/SAC IN WRONG STATE IN MSC--不通知2745--网络结构错误--CELLULAR NETWORK CONFIGURATION ERROR--通知地市（一般因相邻小区数据做错或未做引起）---用EDO或EPO查，LAC和CI号需转换为10进制2748--短信中心地址未分析--NO ANALYSIS FOR SMSC ADDRESS-2749--NO ANALYSIS FOR SMSC AEN--不通知2750--DC/DC CONVERTER FAILURE--通知2751--插件单元丢失--PLUG-IN UNIT MISSING--通知---WTI查插板2754--保险丝断连--FUSE FAILURE--通知2755--时钟创建失效--CARTRIDGE CLOCK FAILURE--通知2757--备用电源故障--CARTRIDGE NON-REDUNDANT POWER SUPPLY FAILURE--通知2758--电源故障--POWER SUPPLY ADAPTER FAILURE--通知，需发单2759--电源保险丝故障--POWER SUPPLY FUSE FAILURE--通知2760--HWAT板故障--HWAT FAILURE--通知2764-- CLS FAILURE2773--自BSC的电路重启确认失败--RESET CIRCUIT ACKNOWLEDGEMENT MISSING FROM BSC--不通知（一般由于传输引起，附加信息第三项为ET号）2777--CDSU CHANNEL SUPERVISION FAILED--不通知2778-- MOST OF CDSU CHANNELS ARE IN FAULTY STATE--通知2779--CDSU PIU SOF TWARN LOADING FAILED--不通知2802--CTU DISK BUFFERING INTERRUPTED--不通知2806--SOMAFI文件更新错误--SOMAFI UPDATE ERROR--通知（索玛菲文件很重要）2827--EMT协议失败--EMT PROTOCOL FAILURE--通知2860--硬盘故障--DISK FAILURE-通知2861--硬盘无法存取--NO ACCESS TO DISK--通知（注：硬盘系统严重故障，不能正常读写数据）2862--硬盘错误--DISK CHECKSUM ERROR--通知2883--磁带满--TAPE MEDIA FULL--不通知2900--引起信号丢失--MULTIFRAME MISSING--通知2909--传输告警--AIS RECEIVED--通知2915--传输告警--FAULT RATE MONITORING--通知地市RCI：SEA=4：CRCT=ET号-1&&-31；看局向发单2925--滑码超过界限--SLIP FREQUENCY LIMIT EXCEEDED-3053--以太网界面错误--ETHERNET INTERFACE FAILURE--通知（大量闪断时需发单，一般伴随2262告警）3083--回声抑制故障--ECHO CANCELLER FAILURE--通知3084--回声抑制信道故障--ECHO CANCELLER CHANNELS FAILURE--通知（可能是ET的某个时隙不好引起，也可能是由于硬件故障引起，一般重启ET后告警就能恢复）3126--用户数据库即将达到满容量门限--DATABASE FILE FOR NORMAL SUBSCRIBERS IS IN DANGER TO GET FULL--无需通知即发单至对端3146--风扇故障--FAN UNIT FAILURE--通知，发单话务3263--CALL ESTABLISHMENT FAILURE IN USER PLANE CONTROL--不通知（由于版本升级引起）3294--容量告警--LICENCE CAPACITY WARNING--通知,发单7404--AIR-CONDITION ABNORMAL7410--WATER7723--FAILURE IN SENDING SYSTEM7724--CONFLICT BETWEEN BSS RADIO NET WORK DATAB7406--TEMPERATURE OUER THE THRESHOLD7408-RECTIFIER ABNORMAL8050--LOSS OF INCOMING 2M SIGNAL8086--LOSS OF CRC MULTIFRAME ALIGNMENT8099--RECEIVED BIT ERROR RATIO（BER）〉IE-39108--通信链路失败--FAILURE IN OMC-NE COMMUNIC ATION LINK--通2494—MSRN RESERVATION RATIO注：漫游号保留的比率，可能引起限呼2099—LIMIT FOR UNSUCCESFUL CALLS EX CEEDED 注：成功的呼叫率低，在忙时需引起重视2397—DATABASE FILE IS IN DANGER TO GET FULL 注：在HLR中出现过，数据库文件满，需在附加信息中确定是哪一个数据库文件满。

诺基亚 760x告警集

一、告警信息分析经过对现网中存在的7607 告警的总结，发现7607 告警主要有以下几种：1 、7607 TRX OPERATION DEGRADEDTRX test result antenna connection faulty.注解：载频检测到天线连接失败2 、7607 TRX OPERATION DEGRADEDRx levels differ too much between main and diversity antennas.注解：主分级接收差异过大3 、7607 TRX OPERATION DEGRADEDEXxx TRX module cooling fan(s) report no rotation注解：载频风扇不转4 、7607 TRX OPERATION DEGRADEDCommissioning file dimate control profile mismatch ,On fans detected注解：风扇配置与实际不符5 、7607 TRX OPERATION DEGRADEDECxx RTC module has detected VSWR above minor limit atantenna注解：RTC 模块检测到天线驻波比值超出门限6 、7607 TRX OPERATION DEGRADEDEXxx TRX module detected only one Rx aignal during RF Cable autodetection注解：射频电缆检测到只有一路接收7 、7607 TRX OPERATION DEGRADEDRSSI detected Rx signal difference exceeding threshold注解：RSSI 检测两路接收信号差值超出门限二、告警处理思路：（一）告警 1 －2 处理这两种7607 告警大多出现在NOKIA METROSITE 中。

NOKIA 基站告警

10
© Nokia Siemens Networks
TBBP530数据配置
处理7607案例案例-2 处理案例
•
第二行RTC2的连线数据库错误，导致RTC2的信号无法传到RTC1，造成RTC1相连的6个载频都缺少一路输入，从而造成6个载频7607告警
11
© Nokia Siemens Networks
12
© Nokia Siemens Networks
TBBP530数据配置
处理7745告警的办法及建议告警的办法及建议-2 处理告警的办法及建议
Hale Waihona Puke • 天线的驻波比正常，但是天线的方位角或下倾角差异过大，例如一幅天线方位角朝东，一
幅朝西，两者接收同一用户信号时必然存在很大差异，导致7607
• 机柜内的Rx连线有误、连接不可靠、接头松动弹起或者连线损坏等会造成7607，原因是
天线的接收信号最终通过这些Rx线进入RTC或DDU，接收通路上的任何问题都会导致 7607
•
7
© Nokia Siemens Networks
TBBP530数据配置
处理7607 （RSSI detected Rx signal difference exceeding threshold）告警的主处理）要方法-2 要方法
主要思路：主要思路：通过观察RSSI测量值，分析RSSI值的特点，可以逐步缩小范围，确定故障点 7607告警的主要原因告警的主要原因 • 天馈线性能可以直接导致该告警，例如两幅天线中的一幅驻波比高，接收性能差，这将导致这幅天线接收的信号电平弱，另一幅天线接收电平正常，两者差值超过10dB
TBBP530数据配置
处理7745（CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD）（处理）告警的办法及建议-1 告警的办法及建议

NOKIA TDD-LTE NodeB告警中英文

FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY FAULTY
FAULTY FAULTY FAULTY OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION
BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE BASE

诺基亚设备告警代码的含义翻译资料

诺基亚设备告警代码的含义翻译告警号星级网优级别告警描述告警解释及处理建议7523 ** 2 TRX TEMPERATURE DANGEROUSLY HIGH TRX 单元中的温度高于80 摄氏度(必须关闭TX 电源以防止组件损坏7524 ** 2 TX FREQUENCY TUNER OUT OF ORDER 某个TX 锁相合成器（PLLI 或PLL2 ）出现故障7525 ** 2 TX MAIN FREQUENCY TUNER OUT OF ORDER TRX 参考频率合成器未锁7526 ** 2 RX FREQUENCY TUNER OUT OF ORDER 某个RX 锁相合成器出现故障7527 ** 2 RX MAIN FREQUENCY TUNER OUT OF ORDER RX 参考频率合成器未锁（PLL3 ）7528 ** 3 TEST LOOP TUNING OUT OF ORDER TRX 环路合成器未锁并可能发生故障7529 ** 2 RECEIVER FAULT 该告警表示某个RX 模块合成器中有故障7530 ** 2 TX OUTPUT POWER LEVEL DECREASED 因为RFU 中的HW 发生故障，TX 功率电平低于给定的值(发射功率电平下降7531 ** 2 TX OUTPUT POWER LOST 如果发送器电源的测量指出断电（尽管传输应该是活的）, TRX 软件产生该告警。

7532 ** 2 TRANSMITTER OUT OF CONTROL 如果发送器电源的测量指出有电（尽管传输应该被关闭）, TRX 软件产生该告警7533 ** 2 TX ANTENNA OR COMBINER CONNECTION FAULTY 该告警指出在TRXTX 接口中的SWR 太高,发射天线或合路器连接失败7535 ** 2 RECEIVING FAULT IN BASEBAND MODULE 使用了分集，则两条EQDSP接收线路都有故障。

诺基亚设备告警代码的含义翻译资料

诺基亚基站设备主要告警中文详细说明处理方案

jk23/0T4`a5f[tuv.
/012345678N .
/0123459: ;#$<=8 ?
16 (31)
Nokia Networks Oy
DN00195563
è×éêìê /í
yB !"(}67(#$?
8IB!9:;[-.!hi#$o!<=>4?_4 #$[ DER >4#$[T DP DE ?@TA @?
¤
ef°±HIZ[ " lA NL{{{ z ;!o 1K @ "¨A"J ~. L@ " Y@ 51 ;.
HI"§
efgh°§H I.|}"~
cd@
^HIcXef"gh
j-.o !"~=ù[,- =(mnI?
DN00195563
Nokia Networks Oy
15 (31)
{{;!S jM pqr stu"^_ ;! ^_"vw xy ;;L; èkMM é ê HI"§
Z[ ìêxyíêZ[.
¤ @ 5"Z[ìêxy &à"ìêxyZ[1zX 5ìêxy.
ìêxyíòêZ[.
@ 5"Z[ìêxy &à"ìêxyZ[1zX 5ìêxy.
ìêxy5.
@ 5"Z[ìêxy &à"ìêxyZ[1zX 5ìêxy.
BCF
BTS 1
TRX 1
TRX 2
TRX 2
BTS 2
TRX 3
BTS 2
TRX 3
TRX 4
TRX 4
3 7606 TRX FAULTY (TRX 1) 7606 TRX FAULTY (TRX 2) 7603 BTS FAULTY (BTS 1) 7606 TRX FAULTY (TRX 3) 7606 TRX FAULTY (TRX 4) 7600 BCF FAULTY (BCF) BTS 1 TRX 1

NOKIA告警宝典

ID alarm_number severitymeans means_c可能的原因1可能的原因2处理方法14924272MMI SYSTEMFILE ERROR MMI系统文件错误人机接口系统检测到磁盘文件如内容出错.如一些人机接口文件出错.用户无法打开人机会话拷贝恢复相应的程序块.5024302ERROR INCOMMANDCALENDAR 指令作业计划错误OMU的硬盘太满,导致日历文件丢失.OMU切换过程中日历命令文件丢失.用ZIWX 查看系统盘和备用盘的空间,用ZIWD将不用的文件删除.5124452UNIT TYPEHAS NOREDUNDANCY 单元没有备份对于需要N+1替换型的功能单元,如SU单元,当所有单元均为WO-EX时,无冗余单元存在.在创建信令系统的过程中,将控制该信令链路的信令单元设为SP的CSSU.用ZUSC将某一单元置为SP-EX状态.5224942MSRNRESERVATION RATIO 漫游号预留比率当交换机的来话话务量很高,VLR分配的MSRN号码达到门限值80%/100%时,系统产生告警.扩大MSRN的号码范围(ZWVM)5325182NO VALIDFALLBACKCOPY FORDEFAULTPACKAGE 默认软件包中无有效的FB备份系统认为默认包无有效的最新的安全备份包.用ZWKS做一系统安全备份.5425251FAILURE INSTORING OFDETAILEDCHARGINGDATA 存入详细计费数据失败系统在将计费数据从CHU的内存写入硬盘时可能由于控制文件TTLOFI的问题导致计费数据丢失特别注意若需对CHU单元进行切换,切换之前千万不要对备用CHU进行重启,否则计费数据可能丢失!保证VDS的连接指向,保存计费数据,先进行主备切换后再对备用单元进行重启5525322ANALYSISFORNETWORKGENERATEDNBR OR FORCHA. CASEIS MISSING NG号或CHARGINGCASE丢失在CM数字分析中却失NETWORKGENERATED的分析在CHARGINGORIGINANALYSIS中却失CHARGINGCASE的分析用ZRDC创建遗漏的NETWORKGENERATED5625482COCA EC1PFAILURE COCA卡故障COCA/ECIP插板检测到错误的定时信号,故导致该插板功能失效.检查M的CLB到COCA/ECIP的插板之间的电缆,或对相关的插板进行检查.5725492FIRSTALARMLIMIT FORUNAVAILABLE VDS-DEVICEDATA FILESREACHED 不可用VDS数据文件数超过门限存储到VDS的数据突增从VDS传送到BC的数据链路失败或被限制修改VDS存储容量的告警门限.当VDS中积压太多的FULL状态的数据文件,可对积压数据文件进行磁带备份后将FULL状态的文件该为TRANSFERRED状态.5825592DATA CALLERRORRATIOEXCEEDED 数据呼叫失败率过高数据业务相关单元故障或半永久连接问题故障对相关数据单元进行诊断,分析处理.5925902ERROR INOPENINGOUTPUTFILE 打开输出文件失败报告生成程序块RFGPRB无法打开将报告输出指向I/O系统.检查逻辑文件指向或查看LOGS,然后按照ERROR CODE 进行处理.6025962SCCPREGISTRATION ERROR SCCP登记错误SCCP或SCCP子系统无定义或状态不对.用NFI/NFJ/ZNHI查询;有错.漏则用ZNFB.ZNFD定义后用ZNGC.ZNHC激活.6126142ERROR INREPORTFORMING 报告格式错误装载模块出错或从硬盘装载报告生成代码出错用ZIWX查询软件包的BLCODE中是否存在该装载模块.用ZAHO查看是否有相应的硬盘告6226202OMUCONNECTIONFAILURE 操作维护单元连接故障OMU单元的负荷过载ASS链路或GSW或SSW的连接或插板故障.由辅助信息的第4字段的故障定位进行诊断判断.6326212FAULTYTIME SLOTIN TESTINGOF TIMESLOT BASEDUNIT 单元使用的时隙在两次连续的测试中不通过在测试中由于测试中断出现的告警提示用ZUSC将单元置为TE状态,然后开始测试.根据测试报告的提示进行处理。

阿尔卡特告警信息

LOSS-OF-SDCCH BER-10E-4 INC-REP WRONG-CONFIGURATION LOSS-OF-TCH LAPD MSG DISTRIBUTION PROBLEM AUDIT-FAIL
67 载频丢失SDCCH告警，由载频故障引起 132 传输误码告警 59 N7信令中断告警 50 基站AN模块配置信息错误告警，一般为基站配置修改时产生 48 丢失话音信道告警，一般为载频故障引起 41 提示级告警，LAPD信令传输异常告警 40 由于O&M引起基站数据读取失败
460 提示级告警,告警系统发现单元存在告警 412 天线驻波比告警 290 传输远端告警,一般为告警单元的上一端出现问题,同FAR-END-ALARM 249 TC信道时隙出现问题 226 提示级告警,错误和失败信息提示 237 传输对端告警,在OMC-R侧观察一般为基站侧中断 233 传输远端告警,一般为告警单元的上一端出现问题
重要
同FAR-END-ALARM
告警类别
告警数
告警说明
AIS NO RESPONSE TO UNIT SUPERVISION MESSAGE
832 传输对端告警,在OMC-R侧观察一般为基站侧中断,同AIS-2-MB 460 提示级告警,指设备在规定时间无信息反馈
UNIT FOUND FAULTY BY ALARM SYSTEM ANTENNA-VSWR-WARNING RAI UNIT FOUND FAULTY BY ALARM SYSTEM CONFUSION IN BSSMAP SIGNALING AIS-2-MB FAR-END-ALARM
23 基站外部告警的提示告警 22 提示级告警，基站AN单元配置出错 20 模块配置错误告警，一般为其他告警的伴随告警 19 基站外部告警 16 提示级外部告警 14 设备停电告警 13 基站重启告警

常见NOKIA告警

一．NOKIA告警概述1.告警查看方法ZEOL:BCF; 查看当前BCF告警;ZEOH：YYYY-MM-DD：BCF= BCF号；查看从输入日期至今的告警;ZAHO；查看BSC当前告警;ZAHP；查看BSC历史告警;2.告警格式我们平时主要关注BTS级别的告警，常见的告警格式如下输出类型：ALARM 故障状态CANCEL 故障结束DISTUR 干扰NOTICE 通知告警级别：*** 需要立即处理** 在一段时间范围内处理* 一般不需处理事件类型：COMM ： communication failureQUAL ： quality of servicePROCES： processing failureEQUIPM： equipment failureENVIR ： environmental failure告警号：7000# ~ 7999# 告警是针对 BTS 出的告警，是我们日常需要关注的。

8000# ~ 8999# 告警是针对传输出的告警2000# ~ 2999# 告警是针对 BSC 级出的告警二．某市NOKIA告警概况为了对NOKIA告警有更形象的认识，2012年2月24日早提取FBSC01、FBSC02、FBSC07、FBSC08、FBSC28五个BSC共2406小区的BTS级当前告警，具体情况如下：按告警级别分：按告警类型分：从以上数据，不难发现，从告警级别看，现网两星告警较多，约占所有告警数的75%；从告警类型看，全网存在最多的告警为7743、7745，两者约占全部告警的40%左右。

这些告警具体表现是什么、该如何消除?下面将对现网中，常见的告警进行分析。

三.常见告警1.信道失败1.1.7743告警告警内容：FBSC01 BCF-0481 BTS-0482 QUAL 2012-02-24 04:25:17.53** ALARM TRX -003 TENGFEIQICXL2D(20176) 7743 MEAN HOLDING TIME BELOW DEFINED THRESHOLD00 00 00 01 01 01 01 01 03 02 3d告警解释：在测量时段内，在指定信道上的平均占用时间低于最小值。

NOKIA 常见告警处理-LN 2010-07

NOKIA告警处理告警级别：按告警号作如下划分0～999 notice 提示◆1000～1999 disturbance 干扰◆2000～2999 MSC 告警（按级别定义为1星★，2星★★，3星★★★）3000～3999 诊断报告号◆4000～5999 外部告警◆6000以上为基站告警。

输出信息：一，常见告警和处理命令：1.查看告警⑴查看当前告警—ZAHO—①CLS=告警级别（AL3，AL2，AL1，not，dis）②NR=告警号例：ZAHO：：CLS=AL3；ZAHO：：NR=2915；⑵查看历史告警—ZAHP—①CLS=告警级别（AL3，AL2，AL1，not，dis）②NR=告警号例：ZAHO：：CLS=AL3：YYYY-MM-DD(年月日用－分隔)，HH-MM-SS(时分秒用－分隔)；ZAHO：：NR=2915：YYYY-MM-DD，HH-MM-SS；2.紧急故障★★★2064ROUTE SET UNA V AILABLE信令路由全阻，导致目的信令点不可达。

1)登录网元，使用命令【ZAHO】核实告警是否存在。

2)核实是否为工程引起。

步骤1 查询故障BSC下是否有基站数据？步骤2 查询A口信令是否为人工闭塞？步骤3 查询故障BSC的历史话务量数据？用命令：【ZNRI：NA0，对应信令点编码；】（NA0到MSC核心网，NA1到BSC方向，用哪一个要根据告警信息中的对端信令点编码判断，4位以下的到BSC，5位以上的到MSC）查看到某一局向的所有路由状态；如果路由状态是UA-INS请检查是否出现#2070 告警，＃2070处于活跃状态则按照＃2070告警处理；如果路由状态是UA-INR请用【ZNRT】查询STP接入，看从STP到相关的信令点是否有信令路由；（可以看到对端的局向名，电话联系分公司或者专业室确定是否有工程）一般是对端设备坏了。

如果是到BSC方向的用【ZEDO：NAME=局向名；】看BSC下挂了多少基站，或者用【ZCEL：NCGR=局向名；】看两个局向间开了多少电路，判断BSC是否在用。

NOKIA告警大全

交换网告警梳理——诺基亚分册目录一.诺基亚设备告警概述 (10)1.1原始告警格式 (10)1.2告警列表格式 (11)二.告警列表 (12)2.13ACCESS SERVICE IS OVERLOADED (12)2.24ACCESS SERVICE REJECT RATE LIMIT EXCEEDED (13)2.333FILE UPDATES TO DISK PREVENTED (13)2.4557STATISTICAL REPORTS LOST (14)2.5690WORKING STATE CHANGE (15)2.61001UNIT RESTARTED (15)2.71007RESTARTED PROGRAM BLOCK (16)2.81016MB INTERFACE FAILURE (17)2.91021PROGRAM BLOCK REWARMING STARTED (18)2.101022PROGRAM BLOCK WARMUP FAILURE (19)2.111024HAND PROCESS ERROR IN PROGRAM BLOCK (19)2.121044ERROR IN SWITCH COMPARE TEST (20)2.131072SIGNALLING LINK OUT OF SERVICE (21)2.141078PROCESS EXCEPTION (23)2.151088CONNECTION ERROR BETWEEN MSC AND SMSC (24)2.161103SIGNALLING MEASUREMENT REPORT LOST (25)2.171183HMS LINE CONNECTION LOST (27)2.181186NO RESPONSE TO HMN SUPERVISION (27)2.191195USSD SERVICE INFORMATION NOT FOUND (28)2.201425OVERFLOW IN ALARM BUFFERING (28)2.211559A-INTERFACE CIRCUIT ALLOCATION FAILURE (29)2.221569CRITICAL LIMIT IN SECURITY REPORTING REACHED (30)2.231574DATA ERROR FOUND BY PROTOCOL (30)2.241575COMPONENT NOT ACCEPTED BY REMOTE END (31)2.251645PROTOCOL MESSAGE QUEUE FULL (32)2.261647OPERATION TIMER EXPIRY (32)2.271667UNHANDLED MESSAGES OVERFLOW (33)2.281860DISK DISTURBANCE (34)2.292005CHECKSUM ERROR IN LOAD MODULE (34)2.302007FILE UPDATING ON AUXILIARY STORAGE IS NOT PROCEEDI (35)2.312012ERROR IN FILE OPENING (36)2.322015MB COMMUNICATION ERROR (37)2.332017FILE DISTRIBUTION ERROR (37)2.342018OVERFLOW IN HANDLING ALARM EVENTS (38)2.352023MAIN CLOCK FAILURE (39)2.362024MAIN CLOCK NEEDS ADJUSTMENT (39)2.372031MB CLOCK FAILURE (40)2.382032SSU CLOCK FAILURE (40)2.392033GSW CLOCK FAILURE (41)2.402034SWI CLOCK FAILURE (42)2.412035SUB CLOCK FAILURE (42)2.422036AONU CLOCK FAILURE (43)2.432037CLG-S FAILURE (44)2.442038MFR CLOCK FAILURE (44)2.452050PLUG-IN UNIT MISSING IN SWITCHING NETWORK (45)2.462051POWER FAILURE IN SWITCHING NETWORK (46)2.472052SWITCH CLOCK FAILURE (46)2.482064ROUTE SET UNAVAILABLE (47)2.492069SIGNALLING LINK TEST FAILED (47)2.502070LINK SET UNAVAILABLE (48)2.512071SIGNALLING LINK TERMINAL FAULTY (49)2.522072FAILURE IN SIGNALLING LINK ACTIVATION OR RESTORATION (50)2.532075COMMUNICATION FAILURE BETWEEN SIGNALLING TERMINAL (51)2.542079LOOP TEST FAILED IN SIGNALLING LINK TERMINAL (52)2.552087LOW TRAFFIC CAPACITY ON CIRCUIT GROUP (53)2.562092AVERAGE SEIZURE TIME BELOW THRESHOLD (53)2.572098CALL OVERLOAD IN EXCHANGE (54)2.582099LIMIT FOR UNSUCCESFUL CALLS EXCEEDED (55)2.592114FR VIRTUAL CONNECTION FAILED (55)2.602115FR USER LINK INTEGRITY VERIFICATION FAILED (56)2.612133SEND BUFFER OVERFLOW IN SIGNALLING TERMINAL (57)2.622137PLUG-IN UNIT LOCATION ERROR (58)2.632138PLUG-IN UNIT SOFTWARE PACKAGE CHECK SUM ERROR (58)2.642139PLUG-IN UNIT SOFTWARE PACKAGE LOAD FAILURE (59)2.652142PLUG-IN UNIT SUPERVISION FAILURE (60)2.662160PREPROCESSOR UNIT RESTART FAILURE (60)2.672171NO USER FOR OSI CLNS (61)2.682175OSI CLNS LINKAGE NOT AVAILABLE (61)2.692185ROUTING OF OSI OUTGOING CALL FAILED (62)2.702186CALL CONTROL ANALYSIS MISSING (63)2.712194ANNOUNCEMENT ID ANALYSIS ERROR (64)2.722202ET FAILURE (64)2.732205ET2FAILURE (65)2.742224ERROR IN MSU HANDLING (65)2.752241SCCP SUBSYSTEM PROHIBITED (67)2.762246SCCP ROUTING FAILURE (67)2.772247SS7ERRONEOUS SIGNALLING MESSAGE (69)2.782250FAILURE IN D-CHANNEL ACTIVATION OR RESTORATION (71)2.792252LOOP TEST FAILED IN PRIMARY RATE ACCESS TERMINAL (72)2.802254SCCP NOT DEFINED FOR NETWORK (72)2.812262OSI SUBNETWORK INTERFACE OUT OF ORDER (74)2.822269ERRONEOUS DISK CACHE SIZE (74)2.832272BOOT LOADING ERROR (75)2.842274SOMAFI ERROR (76)2.852285SIGNALLING TERMINAL FAULTY (77)2.862304TONE GENERATOR FAILURE (78)2.872339SP-CIC->PCM-TSL CONVERSION TABLE UPDATE ERROR (78)2.882347POWER SUPPLY FAILURE IN CPU (79)2.892386OVERWRITING UNTRANSFERRED VDS-DEVICE DATA FILE (79)2.902393FALLBACK COPYING TERMINATED IN ERROR (80)2.912394ERROR IN FINISHING FALLBACK COPYING (81)2.922397DATABASE FILE IS IN DANGER TO GET FULL (82)2.932399DATABASE DISK UPDATES ARE PREVENTED (82)2.942402AFS CONNECTION FAILURE (83)2.952403SERIAL CHANNEL FAILURE (83)2.962410CONNECTION OF A CIRCUIT HAS FAILED IN THE SWITCHING (84)2.972411RELEASING OF A CIRCUIT HAS FAILED IN THE SWITCHING (85)2.982414MISSING ACC REJECTION PERCENTAGES (86)2.992424DISCREPANCY BETWEEN RECORD DATA AND BITMAP (87)2.1002426CHECKSUM ERROR IN FILE BLOCK (88)2.1012439NO LINK BETWEEN MSC AND SMSC (88)2.1022445UNIT TYPE HAS NO REDUNDANCY (89)2.1032477GLOBAL RESET MESSAGE RECEIVED (89)2.1042478MOBILE ACCESS CLASSES ABNORMAL (90)2.1052494MSRN RESERVATION RATIO (91)2.1062503DETAILED CHARGING LOST (91)2.1072504CHARGING FILE FILLING UP (92)2.1082518NO VALID FALLBACK COPY FOR DEFAULT PACKAGE (93)2.1092525FAILURE IN STORING OF DETAILED CHARGING DATA (93)2.1102532ANALYSIS FOR NETWORK GENERATED NBR OR FOR CHA (94)2.1112536SUBSCRIBER DATABASE FILE IN VLR IS FULL (95)2.1122549FIRST ALARM LIMIT FOR UNAVAILABLE VDS-DEVICE (95)2.1132558ECHO CANCELLER CONNECTION FAILURE (96)2.1142562NUMBER NOT FOUND FROM HRNFIL OR INVALID DATA (97)2.1152568ERROR IN GSAPRB ANALYSIS FILE (98)2.1162590ERROR IN OPENING OUTPUT FILE (99)2.1172621FAULTY TIME SLOT IN TESTING OF TIME SLOT BASED UNIT (99)2.1182623TOTAL FAILURE OF TIME SLOT BASED UNIT (100)2.1192624FAULTY TIME SLOT IN TESTING OF MFST (101)2.1202632OSCILLATOR FAILURE (102)2.1212634POWER FAILURE IN SYNCHRONIZATION UNIT (102)2.1222636FAILURE IN OUTGOING CLOCK SIGNAL (103)2.1232638FAILURE IN BUS BETWEEN SYNCHRONIZATION UNITS (104)2.1242639FAILURE IN SYNCHRONIZATION UNIT SWITCHOVER (104)2.1252641FAILURE IN SYNCHRONIZATION SIGNAL (105)2.1262646PROTOCOL ROUTING FAILURE (106)2.1272650STORING OF THE DATA FAILED ON ONE DISK (107)2.1282651STORING OF THE DATA FAILED ON BOTH DISKS (107)2.1292652PHYSICAL DISK IS FULL (108)2.1302653FAILURE IN THE HANDLING OF CONTROL FILES (109)2.1312654NO SERVICE PACKAGE FOR CORE INAP TRIGGER KEY (109)2.1322656CIRCUIT POOL INFORMATION CONFLICT BETWEEN MSC (110)2.1332658CHARGED NUMBER FOR THE SECOND LEG OF REROUTING (111)2.1342661NO CONSISTENT COPY OF DATABASE ON DISK (111)2.1352662NO CONSISTENT DATABASE ANYWHERE (112)2.1362664DATABASE COPY STAYS INCONSISTENT ON SAME DISK (113)2.1372666DBSMAN STOPPED IN ACTIVE UNIT (114)2.1382668CALL ESTABLISHMENT FAILURE (114)2.1392671DATA SERVICE UNIT IS NOT AVAILABLE (116)2.1402675SS7GROUP RESET MESSAGE RECEIVED TO UNUSED CIRCUIT (117)2.1412683ERROR IN MML COMMAND LOG ACCESS (118)2.1422687SYSTEM RESTART IN PROGRESS (120)2.1432692INCORRECT WORKING STATE (121)2.1442693WO-EX UNIT FAULTY (121)2.1452703MAP PROCEDURE FAILURE–HIGH (122)2.1462720TELECOM LINK OVERLOAD (123)2.1472725ADJACENT CELL IDENTIFIER CONFIGURATION ERROR (124)2.1482733OUT OF AVAILABLE VDS-DEVICE DATA FILES (125)2.149273480%OF THE EVENT BUFFER USED (126)2.1502737ECHO CANCELLER CHANNEL FAILURE (126)2.1512740EXCESSIVE DISTURBANCES IN CALL INDEX RESERVATI (127)2.1522741NO SUCCESSFUL CALLS (127)2.1532742BSC/MGW(REL99)OUT OF SERVICE IN MSC (128)2.1542744BSC/MGW(REL99)OR BTS/SAC IN WRONG STATE IN MSC (129)2.1552745CELLULAR NETWORK CONFIGURATION ERROR (130)2.1562748NO ANALYSIS FOR SMSC ADDRESS (131)2.1572751PLUG-IN UNIT MISSING (132)2.1582754FUSE FAILURE (132)2.1592755CARTRIDGE CLOCK FAILURE (133)2.1602756CARTRIDGE POWER SUPPLY FAILURE (134)2.1612757CARTRIDGE NON-REDUNDANT POWER SUPPLY FAILURE (134)2.1622758POWER SUPPLY ADAPTER FAILURE (135)2.1632759POWER SUPPLY FUSE FAILURE (135)2.1642760HWAT FAILURE (136)2.1652761CLAB FAILURE (137)2.1662762SUPERVISION BUS FAILURE (138)2.1672763FAILURE IN BUS BETWEEN CLAB UNITS (138)2.1682764CLS FAILURE (139)2.1692767FEATURE NOT SUPPORTED (139)2.1702770PREPROCESSOR UNIT FAILURE (140)2.1712772BSC/MGW(REL99)CONTINUOUSLY OUT OF SERVICE IN MSC (140)2.1722773RESET CIRCUIT ACKNOWLEDGEMENT MISSING FROM BSC (141)2.1732777CDSU CHANNEL SUPERVISION FAILED (142)2.1742779CDSU PIU SOFTWARE LOADING FAILED (142)2.1752799FRAUD REPORTING NOT SUCCESSFUL (143)2.1762802CTU DISK BUFFERING INTERRUPTED (144)2.1772806SOMAFI UPDATE ERROR (145)2.1782809MASS MEMORY DEVICE POWER SUPPLY FAILURE (145)2.1792812PRINTER SPOOLER ALMOST FULL (146)2.1802818INCORRECT OPERATING STATE (147)2.1812827EMT PROTOCOL FAILURE (147)2.1822843ALARM DIFFERENCE BETWEEN BSC AND OMC (148)2.1832860DISK FAILURE (148)2.1842861NO ACCESS TO DISK (149)2.1852862DISK CHECKSUM ERROR (150)2.1862870MASS MEMORY POWER SUPPLY FAILURE (150)2.1872883TAPE MEDIA FULL (151)2.1882900INCOMING SIGNAL MISSING (151)2.1892902PCM LINE REMOTE END ALARM (152)2.1902908CODE ERROR RATE OVER LIMIT (153)2.1912909AIS RECEIVED (153)2.1922910FRAMING ERROR (154)2.1932911EXCESSIVE CODE ERROR RATE (155)2.1942912BIT ERROR RATE OVER LIMIT (155)2.1952915FAULT RATE MONITORING (156)2.1962923CRC BIT ERROR RATIO OVER LIMIT (157)2.1972925SLIP FREQUENCY LIMIT EXCEEDED (157)2.1982950TRCO FAILURE (158)2.1992952TRANSCODER PLUG-IN UNIT FAILURE (158)2.2002954NO TRAU FRAME SYNCHRONIZATION (159)2.2012955TRANSCODER CHANNEL FAILURE (160)2.2022992BTS AND TC UNSYNCHRONIZATION CLEAR CALLS ON A (161)2.2032993BTS AND TC UNSYNCHRONIZATION CLEAR CALLS ON AB (162)2.2043019NETWORK SERVICE ENTITY UNAVAILABLE (163)2.2053020NETWORK SERVICE VIRTUAL CONNECTION UNAVAILABL (164)2.2063022NETWORK SERVICE VIRTUAL CONNECTION BLOCK PROCEDURE165 2.2073023NETWORK SERVICE VIRTUAL CONNECTION RESET PROCEDURE 165 2.2083024NETWORK SERVICE ENTITY CONFIGURATION MISMATCH (166)2.2093025NETWORK SERVICE VIRTUAL CONNECTION TEST PROCEDURE (167)2.2103026NETWORK SERVICE VIRTUAL CONNECTION PROTOCOL ERROR.. 168 2.2113027.UPLINK CONGESTION ON THE NETWORK SERVICE VIRT (168)2.2123032BSSGP VIRTUAL CONNECTION PROTOCOL ERROR (169)2.2133050NO RESPONSE FROM PLUG-IN UNIT (169)2.2143053ETHERNET INTERFACE FAILURE (170)2.2153084ECHO CANCELLER CHANNELS FAILURE (171)2.2163118UNDERVOLTAGE IN POWER SUPPLY BRANCH UB1OF THE SYS (171)2.2173126DATABASE FILE FOR NORMAL SUBSCRIBERS IS IN DANG (172)2.2183146FAN UNIT FAILURE (173)2.2193156ASSOCIATION ROUTING FAILURE (173)2.2203159SCTP ASSOCIATION LOST (174)2.2213216CONNNECTION BETWEEN MSC AND SMSC FAILED (174)2.2223263CALL ESTABLISHMENT FAILURE IN USER PLANE CONTROL (175)2.2233273(E)GPRS TERRITORY FAILURE (178)2.2243293SCTP PRIMARY PATH NOT AVAILABLE (179)2.2253295LICENCE CAPACITY EXCEEDED (180)2.2263296IWF IP CONNECTION LOST (181)2.2273799MESSAGE BUS FAILURE (181)2.2283937H.248.IP CONNECTION LOST (182)2.2293947VIRTUAL MEDIA GATEWAY IS OUT OF SERVICE (183)2.2304000POWER FAILURE ALARM（外部告警） (184)2.2315001VMS（外部告警） (184)2.2325002VMS（外部告警） (185)2.2335003VMS（外部告警） (185)2.2347208LOCAL BLOCK (185)2.2357220RADIO LOOP OR RX ANTENNA TEST EXECUTION (186)2.2367524TX FREQUENCY TUNER OUT OF ORDER (186)2.2377526RX FREQUENCY TUNER OUT OF ORDER (187)2.2387528TEST LOOP TUNING OUT OF ORDER (188)2.2397530TX OUTPUT POWER LEVEL DECREASED (188)2.2407533TX ANTENNA OR COMBINER CONNECTION FAULTY (189)2.2417549INTERNAL DATA TRANSFER FAILURE (190)2.2427600BCF FAULTY (190)2.2437601BCF OPERATION DEGRADED (191)2.2447602BCF NOTIFICATION (192)2.2457604BTS OPERATION DEGRADED (193)2.2467606RX FAULTY (193)2.2477607TRX OPERATION DEGRADED (194)2.2487608TRX NOTIFICATION (194)2.2497609TRE FAULTY (195)2.2507616OSCILLATOR ADJUSTING TEMPORARILY INTERRUPTED (196)2.2517622CABINET OPEN (196)2.2527700BTS OMU INITIALIZATION (197)2.2537701BCF INITIALIZATION (197)2.2547704PCM FAILURE (198)2.2557705LAPD FAILURE (198)2.2567706BTS O&M LINK FAILURE (199)2.2577711WORKING FULL RATE TCH RATIO BELOW THRESHOLD (199)2.2587715CONTINUOUS RESTARTS OF BCF/TRX (200)2.2597716ACTIVE BCF HW DATABASE DIFFERENCE (200)2.2607717WORKING HALF RATE TCH RATIO BELOW THRESHOLD (201)2.2617723FAILURE IN SENDING SYSTEM INFORMATION TO BTS SIT (201)2.2627724CONFLICT BETWEEN BSS RADIO NETWORK DATABASE A (202)2.2637725TRAFFIC CHANNEL ACTIVATION FAILURE (204)2.2647730CONFIGURATION OF BCF FAILED (204)2.2657735TRX TEST FAILED (206)2.2667736ABIS LOOP TEST FAILED (207)2.2677738BTS WITH NO TRANSACTIONS (208)2.2687740BEATING BTS ALARM (208)2.2697741MEAN HOLDING TIME ABOVE DEFINED THRESHOLD (209)2.2707743MEAN HOLDING TIME BELOW DEFINED THRESHOLD (210)2.2717744EXCESSIVE TCH INTERFERENCE (211)2.2727745CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD (212)2.2737746CH CONGESTION IN CELL ABOVE DEFINED THRESHOLD (213)2.2747753TRX LOOP TEST FAILED (214)2.2757767BCCH MISSING (215)2.2767801MMI CONNECTED TO BASE STATION (216)2.2777805UNIT TEMPERATURE HIGH (216)2.2787808FAULT IN Q1-INTERFACE OF BCF (217)2.2797840SW DOWNLOAD TO UNIT FAILED (217)2.2807861SERVICE TERMINAL CONNECTED TO ABIS TRANSMISSIO (218)2.2817870CABINET DOOR OPEN (219)2.2827890FAULT IN COOLING FAN (219)2.2837900NO CONNECTION TO TRX (220)2.2847939FORWARD POWER TOO LOW AT TX ANTENNA (220)2.2857941TX ANTENNA PERFORMANCE DEGRADED (221)2.2867944MAIN BRANCH LNA OUT OF ORDER IN ANTENNA FILTER UNI (222)2.2877949DIFFERENCE IN RX LEVELS OF MAIN AND DIVERSITY ANTE (222)2.2887990MAINS BREAKDOWN WITHOUT BATTERY BACK-UP (223)2.2897991POWER SUPPLY FAULT (224)2.2908000POWER SUPPLY FAULT (224)2.2918050LOSS OF INCOMING2M SIGNAL (225)2.2928066ALARM INDICATION SIGNAL(AIS)RECEIVED (226)2.2938081LOSS OF FRAME ALIGNMENT (226)2.2948086LOSS OF CRC MULTIFRAME ALIGNMENT (227)2.2958099RECEIVED BIT ERROR RATIO(BER)>1E-3 (228)2.2968102RECEIVED BIT ERROR RATIO(BER)>1E-6 (229)2.2978112FREQUENCY ERROR (229)2.2988179FAR-END ALARM (230)2.2999011FAILURE IN DATA COMMUNICATION NETWORK (231)2.3009041PROCESS RECOVERY IS NEEDED REPEATEDLY (232)2.3019047ALARMS FROM NETWORK ELEMENT NOT ARRIVING (232)2.3029108FAILURE IN OMC-NE COMMUNICATION LINK (233)2.3039112THE MINIMUM NUMBER OF PROCESSES REQUIRED IS NO (234)2.3049122MEASUREMENT DATA HAS NOT ARRIVED FROM THE NE (234)2.3059205FILE SYSTEM IS BECOMING FULL (235)2.3069207NE CLOCK TIME DEVIATION EXCEEDS THE ALARM (236)2.3079212NO CONNECTION TO DATABASE CONNECTION SUPERVIS (236)2.3089224SUPERVISION PROGRAM FAILED (237)2.3099228ALARM DATABASE UPLOAD IN PROGRESS (238)2.3109450CONNECTION FAILURE TO AN SNMP HOST (238)2.3119451SNMP AGENT NOT RESPONDING (239)2.31219800CONNECTION LOST (240)2.31332333CAN NOT INITIALISE CHARGING (240)一. 诺基亚设备告警概述1.1 原始告警格式 ZMMSC2_I OMU-1SWITCH 2006-01-12 16:13:31.98**ALARM OMU-1 1A004-08SAVDAT FILE UPDATING ON AUXILIARY STORAGE IS NOT PROCEEDING 00 10053d 07670000 02A0 4402(1531)2007 交换机名称发送告警单元告警设备类型日期时间告警级别告警输出序列号告警号输出类型出现问题单元告警单元位置告警软件模块告警正文附加信息交换机名称：产生告警的设备名称告警设备类型：SWITCH 交换单元 O&M 操作维护单元 TRANSM 传输单元 POWER 电源设备 EXTERN 外部设备日期时间：告警的发生时间告警级别：*** 需要立即处理** 在一段时间范围内处理 * 一般不需处理 (?). 未知的告警级别以？标识输出类型：ALARM 故障状态 CANCEL 故障结束 DISTUR 干扰 NOTICE 通知出现问题单元：产生告警的功能单元。

诺西GSM基站常见告警及处理建议

诺西GSM常见告警处理建议一、 UltraSite BTS常见告警1、7600 BCF FAULTY 基站故障(1) Crystal oscillator damage 晶体振荡器损坏 Oven oscillator is broken 晶体振荡器故障处理建议：更换BOIA单元。

(2) Base station synchronous failure 基站同步失败处理建议：①检查同步线及接头②检查传输设置的同步设置③更换BOIA单元并重启BCF。

(3) BIOA unit to the temperature too high BIOA 单元温度太高处理建议：①确保周围环境温度在允许的范围内②检查机柜风扇单元③更换BOIA单元。

1、7601 BCF OPERATION DEGRADED 基站性能下降告警(1)Power unit output voltage fault./Power unit input voltage fault./No connection to power unit电源单元输入或输出电压故障，或者无法连接到电源单元处理建议：更换所有出故障的电源单元。

(2)Power unit temperature is dangerously high电源单元温度太高处理建议：①确保周围环境温度在限定范围内②检查机柜风扇③更换电源单元(3)Difference between PCM and base station frequency reference.PCM链路和基站的频率参考有差异处理建议：①检查2M线和2M头子②调整基站主时钟，观察时钟是否稳定③更换BOIA。

(4) Flash operation failed in BOI or TRX BOI或者TRX闪存操作失败处理建议：更换BOIA。

(5)POWER SUPPLY FAULT 电源模块故障处理建议：电源模块（PSUX）没有输出电压，电源模块坏或没有输入电压，更换电源模块或提供电源给电源模块3、7602 BCF NOTIFICATION 基站提示告警(1) Temperature inside the TRX is high 载频高温告警处理建议：①检查风扇单元告警是否处于激活状态②检查并确保没有异物堵塞③确保基站环境温度在允许范围内(2) Temperature inside the TRX is low 载频低温告警处理建议：①确保环境温度在允许的范围内②检查风扇单元。

NOKIA告警宝典

6726362FAILURE IN OUTGOINGCLOCK SIGNAL输出时钟信号失败6826411FAILURE INSYNCHRONIZATION SIGNAL同步信号失败7026462PROTOCOL ROUTINGFAILURE路由协议错误7126501STORING OF THE DATAFAILED ON ONE DISK一个磁盘上数据存储失败7226511STORING OF THE DATAFAILED ON BOTH DISKS一对磁盘上数据存储失败7326531FAILURE IN THEHANDLING OF CONTROLFILES处理控制文件失败7426542NO SERVICE PACKAGE FORCORE INAP TRIGGER KEY 在用户的登记数据中发现有智能英文触发值，但是没有相应的服务包功能7526682CALL ESTABLISHMENTFAILURE呼叫建立失败7626832ERROR IN MML COMMANDLOG ACCESS存取MML指令记录失败7726921INCORRECT WORKINGSTATE错误的工作状态7926931WO-EX UNIT FAULTY主用单元故障8027201TELECOM LINK OVERLOAD电信链路过载8327332NO FREE RING DISK FILE无空余的磁盘循环文件842734280% OF THE EVENTBUFFER USED80％事件缓存被使用8527352EVENT BUFFER OVERFLOW事件缓存溢出8627402EXCESSIVE DISTURBANCESIN CALL INDEXRESERVATION过多干扰在保留呼叫标识时8727411NO SUCCESSFUL CALLS没用成功的呼叫8827421BSC OUT OF SERVICE INMSCMSC中的BSC不可用8927442BSC OR BTS IN WRONGSTATE IN MSCMSC中BSC或BTS状态错误9027452CELLULAR NETWORKCONFIGURATION ERROR无线网络配置错误9227502DC CONVERTER FAILURE直流逆变器故障9327512PLUG-IN UNIT MISSING板卡丢失9527572CARTRIDGE NON-REDUNDANT POWER SUPPLYFAILURE子框无备用电源9627572CARTRIDGE POWER SUPPLYFAILURE机框电源故障ID alarm_number severity means means_c 8227252ADJACENT CELLIDENTIFIERCONFIGURATION ERROR临近小区标志配置错误75152FAILURE IN CONNECTIONTO FREQUENCY HOPPING20375492INTERNAL DATA TRANSFERFAILURE基站内部数据传输故障20475522FAULT IN TRX NON-VOLATILE MEMORYTRX NVRAM内存故障20575602E-CELL ADJUSTMENTFAILEDE-CELL扩展小区调整失败20675912ANTENNA FAULTY天线故障20776031BTS FAULTY BTS故障20876062TRX FAULTY TRX故障20976091TRE FAULTY TRE（传输设备）故障21076172SEVERAL CALLS DROPPEDDUE TO PROBLEM WITHTRANSCODERTRANSCODER问题造成掉话21177042PCM FAILURE PCM故障21277062BTS O&M LINK FAILURE BTS操作维护链路故障21377111WORKING FULL RATE TCHRATIO BELOW THRESHOLD 正常工作的全速率信道比率低于门限21477121WORKING SDCCH CHANNELRATIO BELOW THRESHOLD 正常工作的信令信道比率低于门限21677231FAILURE IN SENDINGSYSTEM INFORMATION TOBTS SITE向BTS送系统信息失败21777252TRAFFIC CHANNELACTIVATION FAILURE话务信道激活失败21877302CONFIGURATION OF BCFFAILEDBCF配置失败21977312BCF SW PACKAGE MAY BEDIFFERENT AS DEFINEDAS A DEFAULT IN BSC BCF软件与BSC中定义的不一致22077342BCCH IS NOT ATPREFERRED BCCH TRXBCCH不在首选的BCCHTRX上22177352TRX TEST FAILED MetroSite TRX测试失败22277372INCONSISTENT DATA INRADIO RESOURCEMANAGEMENT STATE FILES 无线资源管理状态文件中有冲突数据22377382BTS WITH NOTRANSACTIONSBTS没有话务22477412MEAN HOLDING TIMEABOVE DEFINEDTHRESHOLD平均占用时长高于门限22577432MEAN HOLDING TIMEBELOW DEFINEDTHRESHOLD 话务信道平均占用时长低于门限22677442EXCESSIVE TCHINTERFERENCE过大的信道干扰22777452CHANNEL FAILURE RATEABOVE DEFINEDTHRESHOLD TCH和SDCCH信道掉话率高于门限22877462CH CONGESTION IN BTSABOVE DEFINEDTHRESHOLD信道阻塞率高于门限22977522TRX TEST FAILED TRX测试失败23077532TRX LOOP TEST FAILED TRX环路测试失败23177671BCCH MISSING基站阻断23278061UNIT TEMPERATUREDANGEROUSLY HIGH单元温度过高达到危险程度23378091FAULT IN DBUS DETECTEDBY BCFBCF不能和DBUS正常通讯23478122FAULT IN BCF NON-VOLATILE MEMORYBCF NVRAM（内存）故障23578211FRAME CLOCK IS MISSINGFROM MASTER CLOCKGENERATOR 从主时钟发出的时钟信号帧丢失2367825113 MHZ SOURCE CLOCKMISSING FROM MASTERCLOCK OSCILLATOR 从主时钟振荡器发出的13MHZ信号丢失23778282ERROR IN FRAME NUMBERIN MASTER CLOCKGENERATOR时钟单元产生的帧号错误23878311ERROR IN BOOT SOFTWAREDOWNLOADING INFREQUENCY HOPPING 跳频单元启动软件下载错误，无法启动调频功能23978322TEST FAILED ININTERNAL MEMORY OFFREQUENCY HOPPING 调频控制器自检不通过－内存坏24078341FREQUENCY HOPPINGPROCESSOR RESET跳频处理器重启2417838213 MHZ SOURCE CLOCKADJUSTMENT REACHINGTHE LIMIT VALUE13MHZ时钟偏差过大24278392DIFFERENCE INFREQUENCIES BETWEENPCM AND BTS MASTERCLOCK 内部时钟和外部PCM线上的时钟信号不一致24378412INITIALIZATION OF THEUNIT FAILED单元初始化失败24478421NO BCCH TRANSMISSIONACTIVATEDBCCH发射未激活24578602NO CONNECTION TOTRANSMISSION UNITTRU传输单元没有连接24678702CABINET DOOR OPEN柜门打开24778721CABINET TEMPERATURETOO HIGH柜内温度过高24878742TEMPERATURECONTROLLING DEVICEFAULTY温度控制装置故障24979001NO CONNECTION TO TRX TRX无连接25079391FORWARD POWER TOO LOWAT TX ANTENNA送往发射天线的功率太低25279412TX ANTENNA PERFORMANCEDEGRADED发射天线性能下降25379421TX ANTENNA FAULTY发射天线故障25479432FAULT IN MAIN BRANCHLNA OF ANTENNA FILTERUNIT 天线滤波单元的一个主支路LNA故障25579442MAIN BRANCH LNA OUT OFORDER IN ANTENNAFILTER UNIT 天线滤波单元的两个主支路LNA都不可用25679452FAULT IN DIVERSITYBRANCH LNA OF ANTENNAFILTER UNIT 天线滤波单元的分集支路LNA故障25779492DIFFERENCE IN RXLEVELS OF MAIN ANDDIVERSITY ANTENNA 主天线与分集天线接收功率不一致25879501NO CONNECTION TOREMOTE TUNE COMBINERRTC无连接25979522TUNING FAILED INCAVITY OF REMOTE TUNECOMBINERRTC谐振腔调整失败26079532TX ANTENNA PERFORMANCEDEGRADED发射天线性能下降9727582POWER SUPPLY ADAPTERFAILURE电源适配器故障9827592POWER SUPPLY FUSE FAILURE保险丝故障10027612CLAB FAILURE CLAB故障10127622SUPERVISION BUS FAILURE管理总线故障10227702PREPROCESSOR UNIT FAILURE预处理单元故障10327992FRAUD REPORTING NOTSUCCESSFUL FRAUD报告失败10428042SCDFLE DISK UPDATEFAILURE SCDFLE磁盘更新失败10528061SOMAFI UPDATE ERROR SOMAFI更新失败10628092MASS MEMORY DEVICE POWERSUPPLY FAILURE海量存储设备电源故障10728432ALARM DIFFERENCE BETWEENBSC AND OMC BSC和OMC告警不一致10828602DISK FAILURE磁盘故障10928611NO ACCESS TO DISK无法读写磁盘11028622DISK CHECKSUM ERROR磁盘校验和错误11128702MASS MEMORY POWER SUPPLYFAILURE海量存储设备电源故障11228991FAILURE IN O&M CHANNEL操作维护通道故障11329001INCOMING SIGNAL MISSING输入信号丢失11429021PCM LINE REMOTE END ALARM PCM远端告警11529091AIS RECEIVED收AIS11729101FRAMING ERROR帧错误11829121BIT ERROR RATE OVER LIMIT比特误码率超过门限11929151FAULT RATE MONITORING监测到线路故障12129231CRC BIT ERROR RATIO OVERLIMIT CRC比特误码率超过门限12229522TRANSCODER PLUG-IN UNITFAILURE TRANSCODER板卡故障12329541NO TRAU FRAMESYNCHRONIZATION TRAU帧不同步12429551TRANSCODER CHANNELFAILURE TC通道故障12629821TRANSCODER UNIT TRC15CHANNEL EQUIPMENT ORMEMORY FAULT TC的TRC15或内存故障12829921BTS AND TCUNSYNCHRONIZATION CLEARCALLS ON A INTERFACE BTS与TC不同步致A接口掉话13029931BTS AND TCUNSYNCHRONIZATION CLEARCALLS ON ABIS INTERFACEBTS与TC不同步致ABIS接口掉话13230032INCORRECT MEASUREMENTDATA错误的测量数据13330192NETWORK SERVICE ENTITYUNAVAILABLE网络服务实体不可用13430832ECHO CANCELLER FAILURE回声抑制器故障13530842ECHO CANCELLER CHANNELSFAILURE回声抑制器通道故障136322261OPENVIEW PROCESS CRASHED:OVTOPMD OPENVIEW进程崩溃137325022LINK DOWN链路138325101NODE DOWN节点13940001BATTERY DISCHARGED电池放电14240021DISTRIBUTION FUSE FAILURE分布保险丝故障14340031LOW VOLTAGE低电压14440081PDF 2 SYSTEM UNDER VOLTAGEID alarm_number severity means means_c 26179541TX ANTENNA FAULTY发射天线故障26379551SYNTHESIZER OUT OF ORDERIN REMOTE TUNE COMBINER RTC合成器不可用26479612TUNING CARRIER NOT PRESENT IN REMOTE TUNE COMBINER26579682CONTROLLER FAULTY INREMOTE TUNE COMBINER RTC控制器故障26679901MAINS BREAKDOWN WITHOUTBATTERY BACK-UP无备份电池26879912POWER SUPPLY FAULT电源模块故障26979952MAINS BREAKDOWN WITH BATTERY BACK-UP27080001POWER SUPPLY FAULT电源模块故障27280501LOSS OF INCOMING 2MSIGNAL2M输入信号丢失27380661ALARM INDICATION SIGNAL(AIS) RECEIVED收AIS27580811LOSS OF FRAME ALIGNMENT帧定位丢失27780861LOSS OF CRC MULTIFRAMEALIGNMENT CRC复帧定位丢失27880991RECEIVED BIT ERROR RATIO(BER) > 1E-3接收比特误码率> 1E-327981022RECEIVED BIT ERROR RATIO(BER) > 1E-6接收比特误码率> 1E-628081792FAR-END ALARM远端告警28190031BSS MEASUREMENTDATABASE ERRORBSS测量数据库错误28290061DATABASE TABLE ISBECOMING FULL数据表空间将满28490111FAILURE IN DATACOMMUNICATIONNETWORK.数据通信网故障28590151DATABASE CONNECTIONFAILURE数据库连接失败28690301FAILURE IN PASSINGDATA THROUGH THEBUFFER SERVICE缓冲模块传递数据失败28790351MESSAGE SERVICENETWORK FAILURE消息服务网络故障28890411PROCESS RECOVERY ISNEEDED REPEATEDLY进程需要多次恢复28990441PRIMARY CONNECTIONTO INTERMEDIATESYSTEM FAILED主用连接故障29090471ALARMS FROM NETWORKELEMENT NOT ARRIVING网元的告警未送达29191022DATABASE TABLE ISBECOMING FULL数据库表将满29291042FILE SYSTEM ISBECOMING FULL文件系统将满29391082FAILURE IN OMC-NECOMMUNICATION LINK网元与OMC间通信链路故障29491122THE MINIMUM NUMBEROF PROCESSES REQUIREDIS NOT RUNNING运行的进程数量低于最低要求29591132UNABLE TO UPDATEOBJECTCREATION EVENTINTO NMS DATABASENMS数据库中网元创建更新失败29691132UNABLE TO UPDATESTATECHANGE EVENTINTO NMS DATABASENMS数据库中网元状态更新失败29791222MEASUREMENT DATAHAS NOT ARRIVED FROMNETWORK ELEMENT网元测量数据未上传29891242AN INDEX TABLESPACEHAS BECOME FULL.索引表空间将满29991312EFR LICENCE VIOLATION EFR许可证损坏30091362ftp data collection failure FTP数据采集失败30191422GB INTERFACE LICENCEVIOLATIONGB接口许可证损坏30291432HIGH CAPACITY LICENCEVIOLATION高容量许可证损坏30391452MML Command Control EventCollector has failed to parse aMML c控制程序无法解析MML指令30494501CONNECTION FAILURE TOA SNMP HOST连接SNMP主机失败30594512SNMP AGENT NOTRESPONDINGSNMP代理无响应30694792COMMUNICATION LINKFAILURE通信链路故障30795001SMSC Kernel: State DOWN短信内核DOWN 30895031TCP01 link: State DOWN短信与网络链路状态31395041NMS2000 link: State DOWN NMS2000链路中断31496002RPC CLIENT HAS NOTSENT HEARTBEATMESSAGERPC客户端无心跳消息31596462RPC CONNECTION FAILEDTO CNDWNTCNDWNT的RPC连接失效由于CLSU自身的硬件故障导致时钟输出信号失效.与时钟同步相关的单元故障导致输出时钟失效诊断.定位.更换故障插板.时钟同步输入信号失效或丢失检查时钟采集电路及所在的ET及电缆连接.SCCP子系统无定义GT翻译或信令路由地址出错检查信令系统的完整性及正确性.由于某一硬盘故障导致VDS 中的数据只存入一个硬盘.排除硬盘故障后保证双硬盘均为WO-BU状态,然后将当前OPEN状态的文件置为FULL,将故障期间的文件拷入该硬盘,以保证数据文件的正确传送.由于硬盘系统故障导致数据存储失败严格按照NED的步骤进行硬盘系统修复,数据备份,正确设置数据传送的路径.由于硬盘系统故障或硬盘空间已满导致VDS设备无法进行数据读写严格按照NED的步骤进行硬盘系统修复,数据备份,正确设置数据传送的路径.特别注意在故障修复之前不要重启主用单元,以避免数据重写.智能业务触发设置出错用ZRGI查询;用ZRGS修改.话务量剧增导致漫游号码使用完CELL的routing zone设置出错密切关注话务量,及时进行疏忙限流的操作.LOG文件长度不够由于瞬间的故障导致存取MML文件失败.重新设定LOG文件的长度用户操作切换时出现的告警,一般伴随0691的告警系统监测到单元故障,进行复原动作后产生的告警用ZUSI/ZISI查看单元或I/O设备的状态.当2N或N+1替换型的备用单元处于TE-EX状态,此时主用单元故障,系统产生的告警.N+1负荷分担型或无冗余的主用单元发生故障时系统产生的告警.对备用单元进行诊断然后判断是否具备工作条件,若是,则将备用单元进行单元状态改变(TE-SP),然后进行主备倒换.Abis接口的LAPD信令负荷过大。

告警中文解释——诺基亚BSC

交换网告警梳理——诺基亚目录一.诺基亚设备告警概述 (10)1.1原始告警格式 (10)1.2告警列表格式 (11)二.告警列表 (12)2.13ACCESS SERVICE IS OVERLOADED (13)2.24ACCESS SERVICE REJECT RATE LIMIT EXCEEDED (13)2.333FILE UPDATES TO DISK PREVENTED (13)2.4557STATISTICAL REPORTS LOST (14)2.5690WORKING STATE CHANGE (15)2.61001UNIT RESTARTED (16)2.71007RESTARTED PROGRAM BLOCK (16)2.81016MB INTERFACE FAILURE (17)2.91021PROGRAM BLOCK REWARMING STARTED (18)2.101022PROGRAM BLOCK WARMUP FAILURE (19)2.111024HAND PROCESS ERROR IN PROGRAM BLOCK (20)2.121044ERROR IN SWITCH COMPARE TEST (21)2.131072SIGNALLING LINK OUT OF SERVICE (22)2.141078PROCESS EXCEPTION (24)2.151088CONNECTION ERROR BETWEEN MSC AND SMSC (24)2.161103SIGNALLING MEASUREMENT REPORT LOST (26)2.171183HMS LINE CONNECTION LOST (27)2.181186NO RESPONSE TO HMN SUPERVISION (28)2.191195USSD SERVICE INFORMATION NOT FOUND (28)2.201425OVERFLOW IN ALARM BUFFERING (29)2.211559A-INTERFACE CIRCUIT ALLOCATION FAILURE (29)2.221569CRITICAL LIMIT IN SECURITY REPORTING REACHED (30)2.231574DATA ERROR FOUND BY PROTOCOL (31)2.241575COMPONENT NOT ACCEPTED BY REMOTE END (32)2.251645PROTOCOL MESSAGE QUEUE FULL (33)2.261647OPERATION TIMER EXPIRY (33)2.271667UNHANDLED MESSAGES OVERFLOW (34)2.281860DISK DISTURBANCE (34)2.292005CHECKSUM ERROR IN LOAD MODULE (35)2.302007FILE UPDATING ON AUXILIARY STORAGE IS NOT PROCEEDI (36)2.312012ERROR IN FILE OPENING (37)2.322015MB COMMUNICATION ERROR (37)2.332017FILE DISTRIBUTION ERROR (38)2.342018OVERFLOW IN HANDLING ALARM EVENTS (39)2.352023MAIN CLOCK FAILURE (39)2.362024MAIN CLOCK NEEDS ADJUSTMENT (40)2.372031MB CLOCK FAILURE (41)2.382032SSU CLOCK FAILURE (41)2.392033GSW CLOCK FAILURE (42)2.402034SWI CLOCK FAILURE (43)2.412035SUB CLOCK FAILURE (43)2.422036AONU CLOCK FAILURE (44)2.432037CLG-S FAILURE (45)2.442038MFR CLOCK FAILURE (45)2.452050PLUG-IN UNIT MISSING IN SWITCHING NETWORK (46)2.462051POWER FAILURE IN SWITCHING NETWORK (47)2.472052SWITCH CLOCK FAILURE (47)2.482064ROUTE SET UNAVAILABLE (48)2.492069SIGNALLING LINK TEST FAILED (49)2.502070LINK SET UNAVAILABLE (49)2.512071SIGNALLING LINK TERMINAL FAULTY (50)2.522072FAILURE IN SIGNALLING LINK ACTIVATION OR RESTORATION (51)2.532075COMMUNICATION FAILURE BETWEEN SIGNALLING TERMINAL (52)2.542079LOOP TEST FAILED IN SIGNALLING LINK TERMINAL (53)2.552087LOW TRAFFIC CAPACITY ON CIRCUIT GROUP (54)2.562092AVERAGE SEIZURE TIME BELOW THRESHOLD (55)2.572098CALL OVERLOAD IN EXCHANGE (56)2.582099LIMIT FOR UNSUCCESFUL CALLS EXCEEDED (56)2.592114FR VIRTUAL CONNECTION FAILED (57)2.602115FR USER LINK INTEGRITY VERIFICATION FAILED (58)2.612133SEND BUFFER OVERFLOW IN SIGNALLING TERMINAL (59)2.622137PLUG-IN UNIT LOCATION ERROR (59)2.632138PLUG-IN UNIT SOFTWARE PACKAGE CHECK SUM ERROR (60)2.642139PLUG-IN UNIT SOFTWARE PACKAGE LOAD FAILURE (61)2.652142PLUG-IN UNIT SUPERVISION FAILURE (61)2.662160PREPROCESSOR UNIT RESTART FAILURE (62)2.672171NO USER FOR OSI CLNS (62)2.682175OSI CLNS LINKAGE NOT AVAILABLE (63)2.692185ROUTING OF OSI OUT GOING CALL FAILED (64)2.702186CALL CONT ROL ANALYSIS MISSING (65)2.712194ANNOUNCEMENT ID ANALYSIS ERROR (66)2.722202ET FAILURE (66)2.732205ET2FAILURE (67)2.742224ERROR IN MSU HANDLING (67)2.752241SCCP SUBSYSTEM PROHIBITED (69)2.762246SCCP ROUTING FAILURE (69)2.772247SS7ERRONEOUS SIGNALLING MESSAGE (71)2.782250FAILURE IN D-CHANNEL ACTIVATION OR RESTORATION (73)2.792252LOOP TEST FAILED IN PRIMARY RATE ACCESS TERMINAL (73)2.802254SCCP NOT DEFINED FOR NETWORK (74)2.812262OSI SUBNETWORK INTERFACE OUT OF ORDER (75)2.822269ERRONEOUS DISK CACHE SIZE (76)2.832272BOOT LOADING ERROR (77)2.842274SOMAFI ERROR (78)2.852285SIGNALLING TERMINAL FAULTY (79)2.862304TONE GENERATOR FAILURE (80)2.872339SP-CIC->PCM-TSL CONVERSION TABLE UPDATE ERROR (80)2.882347POWER SUPPLY FAILURE IN CPU (81)2.892386OVERWRITING UNTRANSFERRED VDS-DEVICE DATA FILE (82)2.902393FALLBACK COPYING TERMINATED IN ERROR (82)2.912394ERROR IN FINISHING FALLBACK COPYING (83)2.922397DATABASE FILE IS IN DANGER TO GET FULL (84)2.932399DATABASE DISK UPDATES ARE PREVENTED (84)2.942402AFS CONNECTION FAILURE (85)2.952403SERIAL CHANNEL FAILURE (86)2.962410CONNECTION OF A CIRCUIT HAS FAILED IN THE SWITCHING (87)2.972411RELEASING OF A CIRCUIT HAS FAILED IN THE SWITCHING (88)2.982414MISSING ACC REJECTION PERCENTAGES (89)2.992424DISCREPANCY BETWEEN RECORD DATA AND BITMAP (89)2.1002426CHECKSUM ERROR IN FILE BLOCK (90)2.1012439NO LINK BETWEEN MSC AND SMSC (91)2.1022445UNIT TYPE HAS NO REDUNDANCY (91)2.1032477GLOBAL RESET MESSAGE RECEIVED (92)2.1042478MOBILE ACCESS CLASSES ABNORMAL (92)2.1052494MSRN RESERVATION RATIO (93)2.1062503DETAILED CHARGING LOST (94)2.1072504CHARGING FILE FILLING UP (95)2.1082518NO VALID FALLBACK COPY FOR DEFAULT PACKAGE (95)2.1092525FAILURE IN STORING OF DETAILED CHARGING DATA (96)2.1102532ANALYSIS FOR NETWORK GENERATED NBR OR FOR CHA (97)2.1112536SUBSCRIBER DATABASE FILE IN VLR IS FULL (97)2.1122549FIRST ALARM LIMIT FOR UNAVAILABLE VDS-DEVICE (98)2.1132558ECHO CANCELLER CONNECTION FAILURE (99)2.1142562NUMBER NOT FOUND FROM HRNFIL OR INVALID DATA (99)2.1152568ERROR IN GSAPRB ANALYSIS FILE (100)2.1162590ERROR IN OPENING OUTPUT FILE (101)2.1172621FAULTY TIME SLOT IN TESTING OF TIME SLOT BASED UNIT (102)2.1182623TOTAL FAILURE OF TIME SLOT BASED UNIT (103)2.1192624FAULTY TIME SLOT IN TESTING OF MFST (103)2.1202632OSCILLATOR FAILURE (104)2.1212634POWER FAILURE IN SYNCHRONIZATION UNIT (105)2.1222636FAILURE IN OUTGOING CLOCK SIGNAL (106)2.1232638FAILURE IN BUS BETWEEN SYNCHRONIZATION UNITS (107)2.1242639FAILURE IN SYNCHRONIZATION UNIT SWITCHOVER (107)2.1252641FAILURE IN SYNCHRONIZATION SIGNAL (108)2.1272650STORING OF THE DATA FAILED ON ONE DISK (110)2.1282651STORING OF THE DATA FAILED ON BOTH DISKS (111)2.1292652PHYSICAL DISK IS FULL (111)2.1302653FAILURE IN THE HANDLING OF CONTROL FILES (112)2.1312654NO SERVICE PACKAGE FOR CORE INAP TRIGGER KEY (112)2.1322656CIRCUIT POOL INFORMATION CONFLICT BETWEEN MSC (113)2.1332658CHARGED NUMBER FOR THE SECOND LEG OF REROUTING (114)2.1342661NO CONSISTENT COPY OF DATABASE ON DISK (114)2.1352662NO CONSISTENT DATABASE ANYWHERE (115)2.1362664DATABASE COPY STAYS INCONSISTENT ON SAME DISK (116)2.1372666DBSMAN STOPPED IN ACTIVE UNIT (117)2.1382668CALL ESTABLISHMENT FAILURE (118)2.1392671DATA SERVICE UNIT IS NOT AVAILABLE (120)2.1402675SS7GROUP RESET MESSAGE RECEIVED TO UNUSED CIRCUIT (121)2.1412683ERROR IN MML COMMAND LOG ACCESS (122)2.1422687SYSTEM RESTART IN PROGRESS (124)2.1432692INCORRECT WORKING STATE (124)2.1442693WO-EX UNIT FAULTY (125)2.1452703MAP PROCEDURE FAILURE–HIGH (125)2.1462720TELECOM LINK OVERLOAD (126)2.1472725ADJACENT CELL IDENTIFIER CONFIGURATION ERROR (128)2.1482733OUT OF AVAILABLE VDS-DEVICE DATA FILES (129)2.149273480%OF THE EVENT BUFFER USED (129)2.1502737ECHO CANCELLER CHANNEL FAILURE (130)2.1512740EXCESSIVE DISTURBANCES IN CALL INDEX RESERVATI (130)2.1522741NO SUCCESSFUL CALLS (131)2.1532742BSC/MGW(REL99)OUT OF SERVICE IN MSC (132)2.1542744BSC/MGW(REL99)OR BTS/SAC IN WRONG STATE IN MSC (132)2.1552745CELLULAR NETWORK CONFIGURATION ERROR (133)2.1562748NO ANALYSIS FOR SMSC ADDRESS (135)2.1572751PLUG-IN UNIT MISSING (135)2.1582754FUSE FAILURE (136)2.1592755CARTRIDGE CLOCK FAILURE (137)2.1602756CARTRIDGE POWER SUPPLY FAILURE (137)2.1612757CARTRIDGE NON-REDUNDANT POWER SUPPLY FAILURE (138)2.1622758POWER SUPPLY ADAPTER FAILURE (139)2.1632759POWER SUPPLY FUSE FAILURE (139)2.1642760HWAT FAILURE (140)2.1652761CLAB FAILURE (141)2.1662762SUPERVISION BUS FAILURE (142)2.1672763FAILURE IN BUS BETWEEN CLAB UNITS (142)2.1682764CLS FAILURE (143)2.1692767FEATURE NOT SUPPORTED (143)2.1712772BSC/MGW(REL99)CONTINUOUSLY OUT OF SERVICE IN MSC (144)2.1722773RESET CIRCUIT ACKNOWLEDGEMENT MISSING FROM BSC (145)2.1732777CDSU CHANNEL SUPERVISION FAILED (146)2.1742779CDSU PIU SOFTWARE LOADING FAILED (147)2.1752799FRAUD REPORTING NOT SUCCESSFUL (147)2.1762802CTU DISK BUFFERING INTERRUPTED (148)2.1772806SOMAFI UPDATE ERROR (149)2.1782809MASS MEMORY DEVICE POWER SUPPLY FAILURE (150)2.1792812PRINTER SPOOLER ALMOST FULL (150)2.1802818INCORRECT OPERATING STATE (151)2.1812827EMT PROTOCOL FAILURE (151)2.1822843ALARM DIFFERENCE BETWEEN BSC AND OMC (152)2.1832860DISK FAILURE (153)2.1842861NO ACCESS TO DISK (153)2.1852862DISK CHECKSUM ERROR (154)2.1862870MASS MEMORY POWER SUPPLY FAILURE (155)2.1872883TAPE MEDIA FULL (155)2.1882900INCOMING SIGNAL MISSING (156)2.1892902PCM LINE REMOTE END ALARM (156)2.1902908CODE ERROR RATE OVER LIMIT (157)2.1912909AIS RECEIVED (158)2.1922910FRAMING ERROR (158)2.1932911EXCESSIVE CODE ERROR RATE (159)2.1942912BIT ERROR RATE OVER LIMIT (160)2.1952915FAULT RATE MONITORING (160)2.1962923CRC BIT ERROR RATIO OVER LIMIT (161)2.1972925SLIP FREQUENCY LIMIT EXCEEDED (162)2.1982950TRCO FAILURE (162)2.1992952TRANSCODER PLUG-IN UNIT FAILURE (163)2.2002954NO TRAU FRAME SYNCHRONIZATION (164)2.2012955TRANSCODER CHANNEL FAILURE (164)2.2022992BTS AND TC UNSY NCHRONIZATION CLEAR CALLS ON A (166)2.2032993BTS AND TC UNSY NCHRONIZATION CLEAR CALLS ON AB (167)2.2043019NETWORK SERVICE ENTITY UNAVAILABLE (167)2.2053020NETWORK SERVICE VIRTUAL CONNECTION UNAVAILABL (168)2.2063022NETWORK SERVICE VIRTUAL CONNECTION BLOCK PROCEDURE169 2.2073023NETWORK SERVICE VIRTUAL CONNECTION RESET PROCEDURE 170 2.2083024NETWORK SERVICE ENTITY CONFIGURATION MISMATCH (171)2.2093025NETWORK SERVICE VIRTUAL CONNECTION TEST PROCEDURE (171)2.2103026NETWORK SERVICE VIRTUAL CONNECTION PROTOCOL ERROR.. 172 2.2113027.UPLINK CONGESTION ON THE NETWORK SERVICE VIRT (173)2.2123032BSSGP VIRTUAL CONNECTION PROTOCOL ERROR (173)2.2133050NO RESPONSE FROM PLUG-IN UNIT (174)2.2153084ECHO CANCELLER CHANNELS FAILURE (175)2.2163118UNDERVOLTAGE IN POWER SUPPLY BRANCH UB1OF THE SYS (176)2.2173126DATABASE FILE FOR NORMAL SUBSCRIBERS IS IN DANG (176)2.2183146FAN UNIT FAILURE (177)2.2193156ASSOCIATION ROUTING FAILURE (178)2.2203159SCTP ASSOCIATION LOST (178)2.2213188NO RESPONSE TO AAL5CHANNEL SUPERVISION (179)2.2223216CONNNECTION BETWEEN MSC AND SMSC FAILED (180)2.2233263CALL ESTABLISHMENT FAILURE IN USER PLANE CONT ROL (181)2.2243273(E)GPRS TERRITORY FAILURE (184)2.2253293SCTP PRIMARY PATH NOT AVAILABLE (185)2.2263295LICENCE CAPACITY EXCEEDED (186)2.2273296IWF IP CONNECTION LOST (186)2.2283799MESSAGE BUS FAILURE (187)2.2293937H.248.IP CONNECTION LOST (188)2.2303947VIRTUAL MEDIA GATEWAY IS OUT OF SERVICE (189)2.2314000POWER FAILURE ALARM（外部告警） (190)2.2325001VMS（外部告警） (190)2.2335002VMS（外部告警） (190)2.2345003VMS（外部告警） (191)2.2357208LOCAL BLOCK (191)2.2367220RADIO LOOP OR RX ANTENNA TEST EXECUTION (192)2.2377524TX FREQUENCY TUNER OUT OF ORDER (192)2.2387526RX FREQUENCY TUNER OUT OF ORDER (193)2.2397528TEST LOOP TUNING OUT OF ORDER (193)2.2407530TX OUTPUT POWER LEVEL DECREASED (194)2.2417533TX ANTENNA OR COMBINER CONNECTION FAULTY (195)2.2427549INTERNAL DATA TRANSFER FAILURE (195)2.2437600BCF FAULTY (196)2.2447601BCF OPERATION DEGRADED (197)2.2457602BCF NOTIFICATION (197)2.2467604BTS OPERATION DEGRADED (198)2.2477606RX FAULTY (199)2.2487607TRX OPERATION DEGRADED (199)2.2497608TRX NOTIFICATION (200)2.2507609TRE FAULTY (201)2.2517616OSCILLATOR ADJUSTING TEMPORARILY INTERRUPTED (201)2.2527622CABINET OPEN (202)2.2537700BTS OMU INITIALIZATION (203)2.2547701BCF INITIALIZATION (203)2.2557704PCM FAILURE (203)2.2567705LAPD FAILURE (204)2.2577706BTS O&M LINK FAILURE (204)2.2587711WORKING FULL RATE TCH RATIO BELOW THRESHOLD (205)2.2597715CONTINUOUS RESTARTS OF BCF/TRX (206)2.2607716ACTIVE BCF HW DATABASE DIFFERENCE (206)2.2617717WORKING HALF RATE TCH RATIO BELOW THRESHOLD (207)2.2627723FAILURE IN SENDING SYSTEM INFORMATION TO BTS SIT (207)2.2637724CONFLICT BETWEEN BSS RADIO NETWORK DATABASE A (208)2.2647725TRAFFIC CHANNEL ACTIVATION FAILURE (210)2.2657730CONFIGURATION OF BCF FAILED (210)2.2667735TRX TEST FAILED (211)2.2677736ABIS LOOP TEST FAILED (212)2.2687738BTS WITH NO TRANSACTIONS (213)2.2697740BEATING BTS ALARM (214)2.2707741MEAN HOLDING TIME ABOVE DEFINED THRESHOLD (215)2.2717743MEAN HOLDING TIME BELOW DEFINED THRESHOLD (215)2.2727744EXCESSIVE TCH INTERFERENCE (217)2.2737745CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD (217)2.2747746CH CONGESTION IN CELL ABOVE DEFINED THRESHOLD (219)2.2757753TRX LOOP TEST FAILED (220)2.2767767BCCH MISSING (221)2.2777801MMI CONNECTED TO BASE STATION (221)2.2787805UNIT TEMPERATURE HIGH (222)2.2797808FAULT IN Q1-INTERFACE OF BCF (222)2.2807840SW DOWNLOAD TO UNIT FAILED (223)2.2817861SERVICE TERMINAL CONNECTED TO ABIS TRANSMISSIO (224)2.2827870CABINET DOOR OPEN (224)2.2837890FAULT IN COOLING FAN (225)2.2847900NO CONNECTION TO TRX (225)2.2857939FORWARD POWER TOO LOW AT TX ANTENNA (226)2.2867941TX ANTENNA PERFORMANCE DEGRADED (226)2.2877944MAIN BRANCH LNA OUT OF ORDER IN ANTENNA FILTER UNI (227)2.2887949DIFFERENCE IN RX LEVELS OF MAIN AND DIVERSITY ANTE (228)2.2897990MAINS BREAKDOWN WITHOUT BATTERY BACK-UP (229)2.2907991POWER SUPPLY FAULT (229)2.2918000POWER SUPPLY FAULT (230)2.2928050LOSS OF INCOMING2M SIGNAL (231)2.2938066ALARM INDICATION SIGNAL(AIS)RECEIVED (231)2.2948081LOSS OF FRAME ALIGNMENT (232)2.2958086LOSS OF CRC MULTIFRAME ALIGNMENT (233)2.2968099RECEIVED BIT ERROR RATIO(BER)>1E-3 (233)2.2978102RECEIVED BIT ERROR RATIO(BER)>1E-6 (234)2.2988112FREQUENCY ERROR (235)2.2998179FAR-END ALARM (236)2.3009011FAILURE IN DATA COMMUNICATION NETWORK (236)2.3019041PROCESS RECOVERY IS NEEDED REPEATEDLY (237)2.3029047ALARMS FROM NETWORK ELEMENT NOT ARRIVING (238)2.3039108FAILURE IN OMC-NE COMMUNICATION LINK (239)2.3049112THE MINIMUM NUMBER OF PROCESSES REQUIRED IS NO (239)2.3059122MEASUREMENT DATA HAS NOT ARRIVED FROM THE NE (240)2.3069205FILE SYSTEM IS BECOMING FULL (241)2.3079207NE CLOCK TIME DEVIATION EXCEEDS THE ALARM (241)2.3089212NO CONNECTION TO DATABASE CONNECTION SUPERVIS (242)2.3099224SUPERVISION PROGRAM FAILED (243)2.3109228ALARM DATABASE UPLOAD IN PROGRESS (243)2.3119450CONNECTION FAILURE TO AN SNMP HOST (244)2.3129451SNMP AGENT NOT RESPONDING (245)2.31319800CONNECTION LOST (245)2.31432333CAN NOT INITIALISE CHARGING (246)一. 诺基亚设备告警概述1.1 原始告警格式 ZMMSC2_I OMU-1SWITCH 2006-01-12 16:13:31.98**ALARM OMU-1 1A004-08SAVDAT FILE UPDATING ON AUXILIARY STORAGE IS NOT PROCEEDING 00 10053d 07670000 02A0 4402(1531)2007 交换机名称发送告警单元告警设备类型日期时间告警级别告警输出序列号告警号输出类型出现问题单元告警单元位置告警软件模块告警正文附加信息交换机名称：产生告警的设备名称告警设备类型：SWITCH交换单元 O&M操作维护单元 TRANSM传输单元 POWER电源设备 EXTERN 外部设备日期时间：告警的发生时间告警级别：*** 需要立即处理 ** 在一段时间范围内处理* 一般不需处理(?). 未知的告警级别以？标识输出类型：ALARM 故障状态CANCEL 故障结束DISTUR 干扰NOTICE 通知出现问题单元：产生告警的功能单元。

NOKiA 常见告警列表

NOKIA基站故障处理-告警处理

NOKIA基站故障处理-告警处理第三章基站常见告警及处理思路第一节 DE34告警1、7509 RADIO TIMESLOT FAILURE IN TRX――TRX的无线时隙失败。

告警说明：TRX的一些CHDSP中检测到错误情况。

所有的CHDSP时隙告警都用此告警表示。

处理思路：更换TRX。

2、7510 ABIS TESTLOOP FAILURE IN TRX。

――TRX－TRU环路测试中检测到故障。

告警说明：如果同时出现7516和7517告警，则可判断为TRX故障。

如果没有这两个告警，则可判断为TRU故障。

处理思路：检查载频是否同时发生7516和7517告警，如果有，更换TRX单元，如果没有，更换TRUA单元。

3、7514 13MHz CLOCK IS MISSING IN TRX――TRX内部13M时钟丢失。

告警说明：TRX检测到13M时钟发生故障。

该告警多出现在DE34基站重新启动过程中，多数为误告警。

处理思路：Reset出现该告警的TRX，必要时重新拔插一下，如果告警仍然出现，则更换该TRX。

4、7523 TRX TEMPERATURE DANGEROUSLY HIGH。

――TRX温度太高。

告警说明：TRX单元中的温度高于80 oC，必需关闭TX电源以防止组件损坏。

处理思路：当温度降低后， TRX能够正常运行，检查基站风扇单元和基站空调，如果TRX温度正常而告警仍然存在，则更换TRX。

5、7524 TX FREQUENCY TUNER OUT OF ORDER。

――TX频率不稳定告警说明：某个TX锁相合成器出现故障，如果不是跳频模式或者基带跳频模式，则TRX仍能工作，如果另一个合成器也未锁定，则TRX一定被闭锁。

在合成器调频模式下，基站时钟被扰乱或者TRX已坏，该告警是致命告警。

处理思路：检查相应的时钟和时钟线，如果都正常，则更换TRX。

6、7533 TX ANTENNA OR COMBINER CONNECTION FAULTY。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

诺基亚设备告警代码的含义翻译告警号星级网优级别告警描述告警解释及处理建议7523 ** 2 TRX TEMPERATURE DANGEROUSLY HIGH TRX 单元中的温度高于80 摄氏度(必须关闭TX 电源以防止组件损坏)7524 ** 2 TX FREQUENCY TUNER OUT OF ORDER 某个TX 锁相合成器（PLLI 或PLL2 ）出现故障7525 ** 2 TX MAIN FREQUENCY TUNER OUT OF ORDER TRX 参考频率合成器未锁7526 ** 2 RX FREQUENCY TUNER OUT OF ORDER 某个RX 锁相合成器出现故障7527 ** 2 RX MAIN FREQUENCY TUNER OUT OF ORDER RX 参考频率合成器未锁（PLL3 ）7528 ** 3 TEST LOOP TUNING OUT OF ORDER TRX 环路合成器未锁并可能发生故障7529 ** 2 RECEIVER FAULT 该告警表示某个RX 模块合成器中有故障7530 ** 2 TX OUTPUT POWER LEVEL DECREASED 因为RFU 中的HW 发生故障，TX 功率电平低于给定的值(发射功率电平下降)7531 ** 2 TX OUTPUT POWER LOST 如果发送器电源的测量指出断电（尽管传输应该是活的）, TRX 软件产生该告警。

未使用分集，则一条线路有故障。

7536 ** 2 FAILURE IN MAIN RECEIVING PATH OF BASEBAND MODULE 常用的EQDSP 接收线路有故障(使用分集时出现。

否则出现的是告警7535)7537 * 3 FAILURE IN DIVERSITY RECEIVING PATH OF BASEBAND MODULE EQDSP 分集线路有故障（该告警只在使用了分集的情况下出现）7538 ** 2 SIGNALLING ERROR IN ABIS INTERFACE Abis接口信令错误（在电信信令信息传输中TRX 发生故障）7539 ** 2 SIGNALLING ERROR IN DBUS 在内部D 总线信息传输中TRX 发生故障7540 ** 2 AIR INTERFACE DUMB BCCH TRX 报告TSO 未工作7542 * 2 LAPD LINK OFF LAPD 链路被释放7546 ** 2 SAVING OPERATION IN TRX FAILED 在TRX 中的快闪存储器中的保存操作失败7549 ** 2 INTERNAL DATA TRANSFER FAILURE I960 和DSP 之间的通信错误7552 ** 2 FAULT IN TRX NON-VOLATILE MEMORY TRX 软件的各份版本无效7553 ** 2 MEMORY FAULT IN DBUS INTERFACE OF TRX 存储器测试失败（TRX 处理器不能与D 总线通信）7560 ** 2 E-CELL ADJUSTMENT FAILED TRX收到E一CELL请求,当拒绝或超时，停止TRX的配置,则BSC和MMI发送此告警。

7590 ** 2 ANTENNA PERFORMANCE DEGRADED 天线驻波比超出了告警级别的下限（天线调节失衡）7600 *** 1 BCF FAULTY 在基站中出现一个或多个严重故障7601 ** 1 BCF OPERATION DEGRADED 在基站中出现一个或多个主要故障7602 * 3 BCF NOTIFICATION 在基站中出现一个或多个次要故障7603 *** 1 BTS FAULTY 告警代表的扇区内的某个（或某几个）单元出现了一个或多个严重故障7604 ** 1 BTS OPERATION DEGRADED 告警代表的扇区内的某个（或某几个）单元出现了一个或多个主要故障7606 ** 1 TRX FAULTY 在TRX中出现严重告警7607 ** 1 TRX OPERATION DEGRADED 在TRX中出现严重告警7608 * 3 TRX NOTIFICATION 在TRX中出现次要告警7609 *** 1 TRE FAULTY 发生了影响传输单元的一个或多个严重错误7615 * 3 RTS IS IN TEST USE 在TRX 环路测试期间，内部O&M软件正在测试时隙7616 * 3 OSCILLATOR ADJUSTING TEMPORARILY INTERRUPTED Abis频率太高或太低或它的波动幅度太大，使主时钟调谐不可靠造成振荡幅度过大7620 * 3 INCOMING POWER LOST 基站的电源单元失去了市电电源7622 * 3 CABINET OPEN 机柜门打开或机柜盖被卸下7700 * 3 BTS OMU INITIALIZATION BTS 的OMU 启动7701 * 3 BCF INITIALIZATION BCF启动7702 * 3 BCF INITIALIZATION DUE TO BSS RESET 该告警是BSS 启动的BCF 特有的通知7704 ** 1 PCM FAILURE 该告警涉及包含BCF链路的PCM7705 * 1 LAPD FAILURE 该告警涉及TRX的LAPD链路7706 ** 1 BTS O1 LINK FAILURE 基站的O&M链路未处于运行状态。

这将妨碍基站的O&M功能7711 * 3 WORKING FULL RATE TCH RATIO BELOW THRESHOLD 无线网络配置和故障管理检测到处于正常工作状态的全速率话务信道的数量与未闭锁全速率话务信道的数量的比率低于定义的门限7712 * 3 WORKING SDCCH CHANNEL RATIO BELOW THRESHOLD 无线网络配置和故障管理检测到处于正常工作状态的SDCCH 信道的数量和正常工作状态的话务信道的数量的比率低于定义的门限7714 * 3 BCF REMOTE MMI CONNECTION IS IN USE 正在使用BCF 远程MMI 连接7715 * 2 CONTINUOUS RESTARTS OF BCF/TRX BCF或TRX的O&M单元处于复位循环中（BCF 在30分钟之内至少接收到3次复位）7716 * 3 ACTIVE BCF HW DATABASE DIFFERENCE 基站中的HW 数据库不同于BSC HW 数据库的管理系统分配给此BCF 的活跃HW 数据库7719 * 3 TRX INITIALISATION TRX正在被初始化7722 *** 1 ERROR IN BSS RADIO NETWORK DATABASE UPDATE BSS无线网络的恢复或者配置管理系统，根据后台参数的变化或者影响无线网络的故障情况，在更新无线网络配置数据库时失败。

7723 *** 1 FAILURE IN SENDING SYSTEM INFORMATION TO BTS SITE 在恢复措施或BSS 无线网络配置修改后，再将系统信息发送至BTS 站时发生故障7724 *** 1 CONFLICT BETWEEN BSS RADIO NETWORK DATABASE AND CALL CONTROL BSS无线网络的故障恢复或者配置管理系统,根据后台参数的更改或者无线网络中的故障情况,更新了Bss BSDATA7725 ** 3 TRAFFIC CHANNEL ACTIVATION FAILURE 因为呼叫控制在启动话务信道时失败了多次，系统将无线时隙闭锁7728 * 3 OBJECT OUT OF USE BECAUSE OF ERROR IN BTS INTERNAL DIAGNOSTICS 故障恢复收到BTS 的诊断闭锁请求。

如果请求应用的对象处于WO 状态，故障恢复将它们闭锁7729 *** 1 RADIO NETWORK RECOVERY FAILED BSC 无线网络故障恢复失败7730 ** 2 CONFIGURATION OF BCF FAILED 配置BSC 的BCF 失败(BCF 不能发送话务)7731 ** 2 BCF SW PACKAGE MAY BE DIFFERENT AS DEFINED AS A DEFAULT IN BSC BCF 的默认软件包没有解决7733 ** 2 COMMUNICATION FAILURE WITH TRX 时间监控终止或者TRX 向BSC 发出了否定回答信号，而该BSC 中断了正在进行的信息交换方案7734 ** 3 BCCH IS NOT AT PREFERRED BCCH TRX BTS 至少有一个TRX 被定义为首选BCCH TRX ，但是BCCH 信道不在该TRX 上，因此BCCH 的覆盖范围可能减少7735 ** 3 TRX TEST FAILED 对Nokia Metrosite 基站进行的TRX 测试失败7737 ** 2 INCONSISTENT DATA IN RADIO RESOURCE MANAGEMENT STATE FILES BSC 的无线资源管理状态文件发生故障，因此，BTS 的话务容量可能降低7738 ** 2 BTS WITH NO TRANSACTIONS 在监控时段，BTS 没有成功终止的呼叫或者SDCCH 的事务7740 * 3 BEATING BTS ALARM 同一无线网络告警已经连续20 次更改了告警状态（启动／删除），而且都是在通知延迟或删除延迟期间更改的，因此，告警系统滤除了该告警7741 ** 2 MEAN HOLDING TIME ABOVE DEFINED THRESHOLD 在测量时段内，在指定信道上的平均占用时间超出操作员所定义的门限值7743 ** 1 MEAN HOLDING TIME BELOW DEFINED THRESHOLD 在测量时段内，在信道上的平均占用时间低于操作员所定义的最小值7744 ** 1 EXCESSIVE TCH INTERFERENCE 在监控时段内，TCH 时隙在空闲模式下遭受的干扰太大，已经等于或者超过操作员所定义的告警门限百分比(TCH干扰严重(7745 ** 1 CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD 在一个信道中，呼叫因失败而终止的比率超出了操作员设置的门限值7746 ** 2 CH CONGESTION IN BTS ABOVE DEFINED THRESHOLD 由于拥塞基站中的被拒绝信道占用请求与所有信道占用请求之间的百分比超过操作员所定义的告警门限7749 *** 1 E-RACH MISSING BTS 的扩展小区覆盖范围丢失7753 ** 3 TRX LOOP TEST FAILED 预定的或者单独的TRX 环路测试失败7767 *** 1 BCCH MISSING 基站系统出现故障，BSC 恢复无法为BTS 重新配置一个能够工作的BCCH7801 * 3 MMI CONNECTED TO BASE STATION MMI-PC 与BCF 单元的前面板连接器连接7805 * 3 UNIT TEMPERATURE HIGH BCF 单元的内部温度高于75 摄氏度7806 *** 2 UNIT TEMPERATURE DANGEROUSLY HIGH BCFA 单元的内部温度高于85 摄氏度7808 ** 2 FAULT IN Q1-INTERFACE OF BCF Q1 总线测试环路故障7809 *** 2 FAULT IN DBUS DETECTED BY BCF 在从属轮询序列的过程中，BCF 不能从任何从属插件单元接收到任何信息7810 ** 2 FAULT IN WATCH-DOG OF BCF 监视器无法复位BCF7812 ** 2 FAULT IN BCF NON 一VOLATILE MEMORY 快速闪存中，某个存储区中计算的校验和无效，或者保存的校验和已损坏7818 *** 1 FAULT IN MASTER CLOCK OVEN OSCILLATOR 恒温器振荡器发生故障7821 *** 1 FRAME CLOCK IS MISSING FROM MASTER CLOCK GENERATOR BCF 的主时钟发生器丢失了帧时钟输出信号7823 *** 1 2 MHZ REFERENCE CLOCK IS MISSING FROM MASTER CLOCK GENERATOR RF 单元的2MHz 基准时钟丢失7825 *** 1 13 MHZ SOURCE CLOCK MISSING FROM MASTER CLOCK OSCILLATOR 在13MHz 输入中检测到脉冲丢失7826 *** 1 13 MHZ CLOCK MISSING FROM MASTER CLOCK GENERATOR 在13MHz 输入中检测到脉冲丢失7828 ** 2 ERROR IN FRAME NUMBER IN MASTER CLOCK GENERATOR MCLG 缺少帧编号信号输出7829 *** 1 FAULT IN ABIS AND DBUS INTERFACE OF BCF BCF 单元无法控制连接到D 总线的其它BTS 单元7830 *** 1 FREQUENCY HOPPING OUT OF ORDER 跳频处理器初始化失败7831 *** 1 ERROR IN BOOT SOFTWARE DOWNLOADING IN FREQUENCY HOPPING 由于跳频处理器存储器的测试失败7834 *** 1 FREQUENCY HOPPING PROCESSOR RESET 跳频处理器已停止7835 ** 2 DATA ERROR IN FREQUENCY HOPPING BUS 跳频处理器没有接收到帧编号发生器发出的合适的帧编号7836 ** 2 TEST FAILED IN EXTERNAL MEMORY OF FREQUENCY HOPPING 跳频控制器已对外部存储器进行自检7838 ** 1 13 MHZ SOURCE CLOCK ADJUSTMENT REACHING THE LIMIT VALUE BCF将13MHz恒温器振荡器的频率控制在一定的范围内（此告警是由于BCF板时钟与PCM时钟差异所引起的；一般是BCF板时钟漂移所致；）7839 ** 1 DIFFERENCE IN FREQUENCIES BETWEEN PCM AND BTS MASTER CLOCK BCFA SW 比较了13MHZ 频率和PCM 参考7840 ** 2 SW DOWNLOAD TO UNIT FAILED 从BCF 将软件下载到基站其它单元的操作失败7841 ** 2 INITIALIZATION OF THE UNIT FAILED BCF 无法初始化基站的某些单元7842 *** 1 NO BCCH TRANSMISSION ACTIVATED 合路器没有检测到BCCH（广播控制信道）的载波信号7860 ** 1 NO CONNECTION TO TRANSMISSION UNIT 传输单元或者冗余TRUZ不响应Ql 总线上的BCFA 单元发出的轮询命令7863 * 3 FLOATING TRX SWITCHOVER 正在进行浮动TRX 切换操作7870 * 2 CABINET DOOR OPEN 机柜门打开7872 *** CABINET TEMPERATURE TOO HIGH BTS 的冷却系统不能将机柜的温度维护在适当水平7873 *** CABINET TEMPERATURE TOO LOW BTS 的加热系统不能将机柜的温度维护在适当水平7874 ** TEMPERATURE CONTROLLING DEVICE FAULTY 由于单元中的硬件发生故障，HCU（热控制单元）发生致命故障7879 ** 2 SW DOWNLOADING TO FREQ.HOPPING PROCESSOR FAILED 将软件下载到BCFA 单元的跳频处理器的操作失败7882 *** SMOKE DETECTED IN CABINET 检测到BTS 机柜冒烟7890 * FAULT IN COOLING FAN 冷却风扇链中的某个风扇单元不能工作7900 *** 1 NO CONNECTION TO TRX 与TRX连接发生错误7939 ** 1 FORWARD POWER TOO LOW AT TX ANTENNA 在AFE 单元的TX 天线连接处，没有发射功率7941 ** 2 TX ANTENNA PERFORMANCE DEGRADED TX 天线的驻波比高于可调的告警下限7942 *** 1 TX ANTENNA FAULTY TX 天线驻波比超出了告警级别的上限7943 ** 2 FAULT IN MAIN BRANCH LNA OF ANTENNA FILTER UNIT 在AFE 的主接收路径中，LNA （低噪声放大器）中的一个并联放大器发生故障7944 ** 2 MAIN BRANCH LNA OUT OF ORDER IN ANTENNA FILTER UNIT AFE 的主要接收路径中，LNA（低噪声放大器）中的两个放大器分支都已损坏7945 ** 2 FAULT IN DIVERSITY BRANCH LNA OF ANTENNA FILTER UNIT 在AFE 的分集接收路径中，LNA（低噪声放大器）中的一个并联放大器发生故障7946 ** 2 DIVERSITY BRANCH LNA OUT OF ORDER IN ANTENNA FILTER UNIT AFE 的分集接收路径中，LNA（低噪声放大器）中的两个放大器分支都已损坏7947 ** 2 MAIN BRANCH MAST HEAD PREAMPLIFIER OUT OF ORDER MHP（天线杆前置放大器）发生故障7948 ** 2 DIVERSITY BRANCH MAST HEAD PREAMPLIFIER OUT OF ORDER 分集MHP（天线杆前置放大器）的接收放大器发生故障7949 ** 2 DIFFERENCE IN RX LEVELS OF MAIN AND DIVERSITY ANTENNA / TRX 主天线和分集天线之间的Rx 信号强度之差大于限定值（默认为10dB ）7950 *** 1 NO CONNECTION TO REMOTE TUNE COMBINER RTC（远程调谐合路器）不能响应D 总线上的BCFA 单元发出的轮询命令7952 ** 1 TUNING FAILED IN CAVITY OF REMOTE TUNE COMBINER 对某一空腔谐振器的调谐失败7953 ** 2 TX ANTENNA PERFORMANCE DEGRADED TX 天线的驻波比高于可调的告警下限7954 *** 1 TX ANTENNA FAULTY TX 天线的驻波比高于告警上限7955 *** 1 SYNTHESIZER OUT OF ORDER IN REMOTE TUNE COMBINER RTC 的内部调谐合成器不能正常工作7956 *** 1 CONTROLLER OUT OF ORDER IN REMOTE TUNE COMBINER RTC 的内部控制器不能正常工作7960 *** FAULT IN +26V POWER SUPPLY OF REMOTE TUNE COMBINER RTC 的＋26V 电源的电压波动＞13 % （包括彻底损坏）7961 ** 2 TUNING CARRIER NOT PRESENT IN REMOTE TUNE COMBINER 己给RTC 发出调谐命令，但是所有必要的发送器都不能以适当功率级（级别8）发射RF 或者根本不能发射RF7962 * 2 PERIODICAL CAVITY TEST FAILED, CAVITY NOT AVAILABLE RTC 定期对未使用的空腔谐振器进行自检7963 ** 2 CAVITY RESET FAILED, CAVITY NOT AVAILABLE 向RTC 空腔谐振器发出了复位命令，但是RTC 不能使空腔谐振器复位7968 ** 1 CONTROLLER FAULTY IN REMOTE TUNE COMBINER 在RTC 的自测试中检测到故障（RTC 自动执行一些自测试，以保证正常运行）7969 ** 2 FORWARD POWER TOO LOW AT TX ANTENNA TX天线连接上没有传输功能（RTC 自动执行一些自测试，以保证正常运行）7971 ** 2 FAULT IN DIVERSITY BRANCH LNA OF RECEIVER MULTICOUPLER 在RMU 的分集接收路径中，LNA（低噪声放大器）中的一个并联放大器发生故障7972 ** 2 MAIN BRANCH LNA OUT OF ORDER IN RECEIVER MULTICOUPLER 在RMU 的主接收路径中，LNA（低噪声放大器）中两个并联放大器发生故障7973 ** 2 DIVERSITY BRANCH LNA OUT OF ORDER IN RECEIVER MULTICOUPLER 在RMU 的分集接收路径中，LNA（低噪声放大器）中两个并联放大器都发生故障7974 ** BOOSTER TEMPERATURE TOO HIGH 增强器单元的温度太高7975 ** BOOSTER TX CONNECTION FAULTY 增强器中的SWR 太高。