量具中英文对照表
量具中英文对照
量具中英文对照量具 Measuring Tools板规 plate gauge比例规 proportional dividers标准规 standard gauge齿轮规 gear tooth gauge丁字尺 T-square分线规 divider;dividers钢尺 steel rule工作量规 working gauge厚薄规 feeler(gauge)角尺 angle square角规 angle gauge金属卷尺 metallic tape卡尺 calipers;caliper刻度尺 graduation ruler块规 gauge(block)量规 gauge螺距规 screw pitch gauge螺纹千分尺 screw micrometer内径千分尺 micrometer inside caliper;inside micrometer 内卡钳 inside caliper皮尺 tape(/measure)平面规 surface gauge千分表 dial indicator千分尺 micrometer曲尺carpenter’s square三角尺 set square深度千分尺 micrometer depth gauge; depth micrometer椭圆规 ellipsograph外径千分尺 outside micrometer外卡钳 outside caliper隙规 gap(/clearance) gauge线规 wire gauge斜角规 bevel square游标卡尺 vernier caliper圆规 compasses折尺 folding pocket measure(/ruler)直尺 straight edge中心规 centre gauge锥度规 taper gauge组合角尺 combination set可调的磁力架----Magnetic stand with fine adjustment点接触杠杆千分表 ---Lever dial indicator point contact length 卡钳式内径千分尺－Internal quick caliper dial gauge孔的轮廓量规－Bore profile gauge KT磁性吸座－－Magnetic stand花岗岩平台（精度1极）Granite table, accuracy 1外径千分尺标准棒――micrometer standard装有T型槽的平台-Tenon and T-slot incl. installation。
测量工具中英文对照表大全
测量工具中英文对照表大全测量工具中英文对照表heodolite 经纬仪Water Level 水位仪Level Ruler 水平尺Casing gradienterCoating thicknessMeasurer 涂层测厚仪Ultrasonic thicknessmeasurer 超声波测厚仪Ultrasonic crackdetector 超声波裂纹测试仪Digital thermometer 数字温度计radiation thermometer 辐射温度计Gradient Reader 坡度读数器Volometer 万用表MegaOhmmeter 兆欧表Earthing resistanceReader 接地电阻读数表Plug gauge 圆柱塞规Magnifying glass 放大镜Plummet 铅锤Profile projector 投影仪Pin Gauge 针规(不知道和plug gauge 的区别在哪里,知道的请指正)Gauge block 块规Bore gauge 百分表A vernier caliper 游标卡尺Coordinate Measureing Machine(CMM) 三尺元Pressure gague寸压力计电度厚度测试仪(Electroplating THK.Tester)转(扭)力仪(Twisting Meter)螺纹规(Thread Gauge)块规(Block Gauge)环规(Ring Gauge)力矩计(Torque Meter)塞规(Plug gage)高度仪(Altitude gauge)塞尺/间隙规(Clearance gauge)千分卡尺(Micrometer Calipers )“过” -- “不过” 验规(通-止规) [go-no-go gauge]游标卡尺(Vernier Caliper)电子卡尺(Digital caliper)深度千分尺(Depth Micrometer)销(针)规(Pin Gauge)投影仪(Projector )数字高度测量仪(Digital Height Gauge)表面处理测试仪(Surface Finish Tester)内/外径千分尺(Inside/outer Micrometer)洛(威)氏硬度仪[(HRC/HV) Hardness Tester)]温度计(Thermometer)孔规(Bore Gauge)电子称(Electric/digital Balance)三坐标测试仪 (CMM)万用表(Multimeter)1.刀口型直尺:knife straigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪 imaging level meter7铸铁平板 cast iron surface plate 8.岩石平板 granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪 roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens cast surface14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparisonspecimens-ground,turned,bored,mi lled,shape and planed15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machining surfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓 traced profile20.基准轮廓 reference profile21.总轮廓 total profile22.原始轮廓 primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storing stylus instrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profilefiltering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument41.静测力的变化change of static measuring force 42.静态测力 static measuring force43.动态测量力 dynamic measuring force44.滞后hysteresis45.测头的测量范围 transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力 instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输 vertical profile component transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blasted surfaces54产品结构几何量计术规范（GPS）geometrical productspecifications(GPS)55表面结构 surface texture56接触式仪器的标称特性 nominal characteristics of contact instruments57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差 maximum permissible error59圆柱直齿渐开线花键量规 gauges for straight cylindrical involute splines60齿厚游标卡尺 Gear tooth verniercalipers61齿轮渐开线样板the involute master of gear62齿轮螺旋线样板 the helix master of gear63矩形花键量规 gauges for straight –sided splines64测量蜗杆 master worm65万能测齿仪 universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机 Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument 70便携式齿轮齿距测量仪 manual gear circular pitch measuring instrument71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuring instrument75梯形螺纹量规 gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸 Types and dimensions of metric trapezoidal screw threads79.普通螺纹量规型式与尺寸 Types and dimensions of gauges purpose screw threads80.非螺纹密封的管螺纹量规 Gauges for pipe threads prcessure-tight joints are not made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差 maximum permissible error83.间隙螺纹量规 Clearance screw gauge84.量针Bar gauge85.螺纹样板 Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made on the threads87.刀具预调测量仪? 精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator一般术语：1.几何量 geometrical product2.量值value(of a quantity)3.真值true value(of a quantity)4.约定真值 conventional true value(of a quantity)5.单位unit(of measurement)6.测量measurement7.测试measurement and test8.检验inspecte9.静态测量static measurement10.动态测量dynamic measurement11.测量原理principle of measurement12.测量方法method of measurement13.测量程序measurement procedure14.被测量measurand15.影响量influence quantity16.变换值transformed value(of a measurand)17.测量信号measurement signal18.直接测量法direct method of measurement19.间接测量法indirect method of measurement20.定义测量法definitive method of measurement21.直接比较测量法direct-comparison method of measurement22.替代测量法substitution method of measurement23.微差测量法differential method of measurement24.零位测量法nulll method of measurement25.测量结果result of a measurement26.测得值measured value27.实际值actual value28.未修正结果uncorrected result （of a measurement）29.已修正结果corrected result(ofa measurement)30.测量的准确度accuracy of measurement 31.测量的重复性repeatability of measurement32.测量复现性reproducibility of measurements33.实验标准偏差experimental standard deviation34.测量不确定度uncertainty of measurement35.测量绝对误差 absolute error of measurement36.相对误差 relative error37.随机误差random error38.系统误差 systematic error39.修正值correction40.修正系数correction factor41.人员误差personal error42.环境误差environmental error43.方法误差error of method44.调整误差adjustment error45.读数误差reading error46.视差parallax error47.估读误差 interpolation error48.粗大误差parasitic error49.检定verification50.校准calibration51.调准gauging52.调整adjustment几何量测量器具术语1.几何量具测量器具dimensional measuring instruments2.长度测量器具length measuring instruments3.角度测量器具angle measuring instruments4.坐标测量机coordinate measuring machine5.形状和位置误差测量器具form and position error measuring instruments6.表面质量测量器具surface quality measuring instruments7.齿轮测量器具gear measuring instruments8.实物量具（简称“量具”）material measure9.测量仪器（简称“量仪”）measuring instruments10.测量链measuring chain11.测量装置measuring system12.指示式测量仪器indicating(measuring )instrument13.记录式测量仪器recording （measuring）instrument14.累计式测量仪器totalizing(measuring)instrument 15.积分式测量仪器integrating(measuring)instrument16.模拟式测量仪器analogue(measuring)instrument17.数字式测量仪器digital(measuring)instrument18.测量变换器measuring transducer19.传感器sensor20.指示装置indicating device21.记录装置recording device22.记录载体recording medium23.标尺标记scale mark24.指示器index25.标尺scale26.度盘dail测量器具术语1.标称值nominal value2.示值indication(of a measuring instrument)3.标尺范围scale range4.标称范围nominal range5.标尺长度scale length6.标尺分度scale division7.分度值value of a scale division8.标尺间距scale spacing9.线性标尺linear scale10.非线性标尺non-linear scale11.标尺标数scale numbering12.测量仪器的零位zero of a measuring instrument13.量程span14.测量范围measuring range15.额定工作条件vated operating conditions16.极限条件reference condition17.标准条件reference condition18.仪器常数instrument constant19.响应特性response characteristic20.灵敏度senstivity21.鉴别力discrimination22.分辨力resolution（of an indicating device）23.死区dead band24.准确度accuracy of a measuring instruments25.准确度等级accuracy class26.重复性repeatability of a measuring instrument27.示值变动性varation of indication28.稳定度stability 29.可靠性reliability30.回程hysteresis31.漂移drift32.响应时间response time33.测量力（简称“测力”）measuring force测量器具术语1.实物量具示值误差error of indication of a material measure2.测量仪器示值误差error of indication of a measuring instrument3.重复性误差repeatability error of a measuring instrument4.回程误差hysteresis error5.测量力变化variation of measuring force6.测量力落差hysteresis of measuring force7.偏移误差bias error (of a measuring instrument)8.允许误差maximum permissible errors(of measuring instruments)9.跟踪误差tracking error (of a measuring instrument)10.响应率误差response-law error (of a measuring instrument)11.量化误差quantization error (ofa measuring instrument)12.基值误差datum error (of a measuring instrument)13.零值误差zero error (of a measuring instrument)14.影响误差influence error15.引用误差fiducial error16.位置误差position error17.线性误差linear error18.响应特性曲线response characteristic curve19.误差曲线error curve20.校准曲线calibration curve21.修正曲线correction curve长度测量器具量具类1.量块gauge block2.光滑极限量规plain limit gauge3.塞规plug gauge4.环规ring gauge卡规snap gauge5.塞尺feeler gauge6.钢直尺steel gauge7.精密玻璃线纹尺precision glass linear scale8.精密金属线纹尺precision metal linear scale9.半径样板radius template卡尺类1.游标卡尺vernier caliper2.带表卡尺dial caliper3.电子数显卡尺calliper with electronic digital display4.深度标游卡尺depth vernier caliper5.电子数显深度卡尺depth caliper with electronic digital display6.带表高度卡尺dial height calliper7.高度游标卡尺height vernier caliper8.电子数显高度卡尺height caliper with electronic digital display9.焊接检验尺calliper for welding inspection千分尺类1.测微头micrometer head2.外径千分尺external micrometer3.杠杆千分尺micrometer with dial comparator4.带计数器千分尺micrometer with counter5.电子数显外径千分尺micrometer with electronic digital display6.小测头千分尺small anvil micrometer7.尖头千分尺point micrometer8.板厚千分尺sheet metal micrometer9.壁厚千分尺tube micrometer10.叶片千分尺blade micrometer11.奇数沟千分尺odd fluted micrometer12.深度千分尺depth micrometer13.内径千分尺internal micrometer14.单杆式内径千分尺single-body internal micrometer15.表式内径千分尺 dail internal micrometer16.三爪式内径千分尺three point internal micrometer17.电子数显三爪式内径千分尺three point internal micrometer18.内测千分尺inside micrometer 指示表类1.指示表 dial indicator2.深度指示表depth dial indicator3.杠杆指示表dial test indicator4.内径指示表bore dial indicator5.涨弹簧式指示表 expanding head bore dial indicator6.钢球式内径指示表ball type bore dial indicator7.电子数显指示表dial indicator with electronic digital display8.杠杆卡规indicating snap gauge9.带表卡规dial snap gauge10.带表外卡规outside dial snap gauge11.带表内卡规inside dial snap gauge12.测厚规thickness gauge13.扭簧比较仪microcator14.杠杆齿轮比较仪mechanical dial comparator15.电子量规electronic gauge16.电感式传感器inductance type transducer17.指示装置indicating device18.电感测微仪inductance micrometer19.峰值电感测微仪peak inductance micrometer个20.电感内径比较仪inductance bore comparator21.瞄准传感器aiming transducer页脚内容11。
量具中英文对比表[推荐]
![量具中英文对比表[推荐]](https://img.taocdn.com/s3/m/2bfdbe352bf90242a8956bec0975f46526d3a75d.png)
量具中英文对照表(机械专业)游标卡尺－――Vernier Caliper数显卡尺――Digital Caliper带表卡尺――Digital Slide Caliper深度――depth gauge数显深度尺――Digital depth gauge卡尺――Caliper角尺――angle square钢尺――steel rule外径千分尺――external micrometer,平面规surface gauge外径千分尺――external micrometer外径千分尺标准棒――micrometer standard外径千分尺架子――micrometer stand带表外径千分尺――Indicator dial micrometer千分表外径规―――Dial indicator snap gauges外径深度尺――depth micrometer内径千分尺――Internal micrometer花岗岩平台（精度1极）Granite table, accuracy 1装有T型槽的平台-Tenon and T-slot incl. installation 千分表-Dial indicator 数显千分表-Digital indicator 磁性吸座－－Magnetic stand孔的轮廓量规－Bore profile gauge KT卡钳式内径千分尺－Internal quick caliper dial gauge点接触杠杆千分表---Lever dial indicator point contact length 可调的磁力架----Magnetic stand with fine adjustment游标高度尺---Vernier height gauge游标高度尺Digital height gauge尺规\刀规－Straight edge直尺－steel ruler角尺－Square卷尺Locking tape measure。
常用量具中英文对照.
常用量具中英文对照及检查比例序号量具名(中文)量具名(英文)测量精度车床检查比例FQC检查比例1三座标CMM1pcs/6hours C=0,AQL:0.42数字比较仪DIGITAL COMPARATOR5pcs/2hours C=0,AQL:0.43TESA SCANPLUS TESA2pcs/6hours C=0,3pcs/lot4镭射(LASER MICROMETER)0.25m m5pcs/2 Hours C=0,AQL:0.45基准尺SNAP MICROMETER1m m5pcs/2 Hours C=0,AQL:0.46电子千分尺MICROMETER3m m5pcs/4 Hours C=0,AQL:1.07坑卡BLADE MICROMETER10m m5pcs/4 Hours C=0,AQL:1.08深度表DEPTH GAUGE3m m5pcs/4 Hours&2pcs/6Hours C=0,AQL:1.0&C=0,10pcs/lot 9高度尺HEIGHT GAUGE2m m5pcs/4 Hours C=0,AQL:1.010塞规PIN GAUGE 5pcs/4 Hours C=0,AQL:1.011六角塞规HEX GAUGE5pcs/4 Hours C=0,AQL:1.012气动测位仪 AIR GAUGE0.1/0.2/0.5/1m m5pcs/2 Hours C=0,AQL:0.413内径量表BORE GAUGE10m m5pcs/4 Hours C=0,AQL:1.014内径千分尺INSIDE MICROMETER3m m5pcs/4 Hours C=0,AQL:1.015槽规GAUGE BLOCK5pcs/4 Hours C=0,AQL:1.016内牙规THREAD PLUG GAUGE5pcs/4 Hours C=0,30pcs/lot17外牙规THREAD RING GAUGE5pcs/4 Hours C=0,30pcs/lot18同轴度仪CONCENTRICITY GAUGE1m m5pcs/4 Hours C=0,10pcs/lot19专用治具FIXTURE5pcs/4 Hours C=0,30pcs/lot20圆度仪ROUNDNESS TESTER±0.1m m1pcs/6hours C=0,3pcs/lot21投影PROJECTOR15m m2pcs/6hours&1pcs/12hours C=0,3pcs/lot22锯开投影PROJECTOR(CUTTING)1pcs/12hours-23轮廓仪CONTRACER±0.1m m1pcs/12hours-24锯开轮廓仪CONTRACER(CUTTING)1pcs/12hours-25光洁度仪SURFACE ROUGHESS±0.1m m2pcs/6hours&1pcs/6hours C=0,3pcs/lot26工具显微镜MICROSCOPE1pcs/6hours主要测量部位三座标主要用于测量那些体积较大而形状又不规则的零件.只要是用离散性取点来组成线,面(包括曲面),所以只要是可以用点,线,面关联起来的尺寸基本都可以量数字比较仪测量原理与量基准尺一样,不同的是它除了量外径之外还可以测深度,两者都需要与被测尺寸相接近的基准做比较,且基准越接近被测尺寸越好.当然所有测量还得在外径/外牙牙中径和牙底径外径(公差小于等于0.002)外径(公差0.002~0.005)外径(公差大于0.005)外径(槽宽0.7~3.0之间的外径)深度(0~25之间)深度(25以上)内孔(不用做CPK)六角内孔内孔(要做CPK,且公差比较小)内孔(要做CPK)内孔(要做CPK)槽宽内牙外牙h j r bc所有形位公差都可用圆度仪内倒角/公差小的外倒角/孔内无法测量的用轮廓仪测不到的光洁度Ra,Rz,Ry量还得在量具测量量程之内方可.。
各种量具中英文简写对照表
中文
材质 外观 外径 内径 直径 半径 宽度 长度 深度 高度 螺纹 角度 沟 沟宽 沟径 沟位置 倒角 圆角 面粗度 同轴度 平行度 直线度 垂直度 圆度 平面度 位置度 跳动度 对称度 距离 技术要求 钝化 镀镍 镀铬
塞尺
英文
material appearance out diameter inside diameter diameter radius width length depth height thread angle groove groove wide groove diameter groove position chamfer fillet surface roughness concentricity parallelism straightness perpendicularity roundness flatness position runout symmetry distance Note passivation nickle plating chrome plating feeler gauge
英文
英文简写
VIS C. H.C Cen.L.C OFF.C MIC. B.MIC I. MIC O.MIC G.T.MIC GRO.M D.T.IND. D.D.IND S.P.G S.R.G P.G S.P.GUGE C-G R-G ANG.G B.G S.G CER.B D.C.G THR.W V-B CMM L.H.G R.T SUR.T MIC.S ANOD. d.c.g
height caliper center line caliper offset caliper micrometer blade micrometer inside micrometer outside micrometer gear tooth micrometer groove micrometer depth dial indicator screw plug gauge screw ring gauge pin gauge screw pitch guage c-gauge r-gauge angle gauge snap gauge cera block dial caliper gauge three wires v-block CMM Linear Height Gauge roundness test surf test microscope anodization dial caliper gauge
量具中英文对照
量具中英文对照卡规snap gauge5.塞尺feeler gauge 卡尺类6.钢直尺 steel gauge7.1.游标卡尺vernier caliper 精密玻璃线纹尺precision glass linear scale8.精密金属线纹尺2.带表卡尺dial caliper precision metal linear scale9. 半径样板radius template 3.电子数显卡尺测量器具术语calliper with electronic digital display深度标游卡尺depth vernier caliper 4.1.实物量具示值误差error of indication of a 5.电子数显深度卡尺material measuredepth caliper with electronic digital display2.测量仪器示值dial height calliper 误差error of indication of a 6.带表高度卡尺measuring instrumentheight vernier caliper7.高度游标卡尺3.caliper with 重复性误差repeatability error of a measuring height 高8.电子数显度卡尺instrumentelectronic digital display4.回程误差calliper for welding inspection hysteresis error9.焊接检验尺5.千分尺类测量力变化 variation of measuring force6. 测量力落差hysteresis of measuring force7.偏移误差bias error micrometer head1.测微头(of a measuring instrument)8.允许外径千分尺2.external micrometer误差maximum permissible errors(ofmeasuring instruments)3.杠杆千分尺micrometer with dial comparator9.跟踪误差tracking error 带计数器千分尺4.micrometer with counter (of a measuring instrument)电子数显外径千分尺 5.10.micrometer with electronic digital display 响应率误差response-law error (of a measuringinstrument)小测头千分尺small anvil micrometer 6.11.7.量化误差quantization error (of a measuring 尖头千分尺point micrometerinstrument)板厚千分尺sheet metal micrometer 8.12.基值误差datum error 壁厚千分尺9.tube micrometer (of a measuringinstrument)blade micrometer10.叶片千分尺13.零值误差zero 奇数沟千分尺11.odd fluted micrometer error (of a measuringinstrument)12.深度千分尺depth micrometer14.影响误差internal micrometer influence error 内径千分尺13.15.引用误差 14.单杆式内径千分尺fiducial error16.single-body internal micrometer位置误差position error17.线性误差 dail internal micrometer 15.表式内径千分尺linear error18. 响应特性曲线response characteristic curve 三爪式内径千分尺16.19.误差曲线error curvethree point internal micrometer20.电子数显三爪式内径千分尺17. 校准曲线calibration curve21.修正曲线three point internal micrometer correction curve测量器具术语inside micrometer 内测千分尺18.1.标称值nominal value长度测量器具2. 量具类示值indication(of a measuring instrument)3.gauge block标尺范围scale range 量块1.4.plain limit gauge 光滑极限量规2.标称范围nominal range 5.标尺长度scale length plug gauge 塞规3.scale division标尺分度6.ring gauge环规4.7.分度值value of a scale division 13.记录式测量仪器recording（scale spacing measuring）instrument 8.标尺间距14.9.线性标尺linear scale 累计式测量仪器totalizing(measuring)instrument 非线性标尺non-linear scale10.15.scale numbering11.标尺标数积分式测量仪器integrating(measuring)instrumentof a measuring instrument 12.测量仪器的零位zero16.模拟式测量仪器13.量程spananalogue(measuring)instrument17.数字式测量仪器14.测量范围measuring rangedigital(measuring)instrument18.测量变换器measuring transducer 15.额定工作条件vated operating conditions19.传感器sensor极限条件16.reference condition20.指示装置reference condition indicating device 17.标准条件21.18.仪器常数instrument constant 记录装置recording device22.记录载体response characteristic recording medium 19.响应特性23.20.灵敏度senstivity 标尺标记scale mark24.鉴别力指示器discriminationindex 21.25.22.分辨力resolution标尺scale （of an indicating device）26.度盘dail 23.死区dead band一般术语：准确度24.accuracy of a measuring instruments1.几何量 geometrical product accuracy class 25.准确度等级2.量值value(of a quantity) 26.重复性3.真值repeatability of a measuring instrument true value(of a quantity)4.约定真值示值变动性varation of indication 27.conventional true value(of a quantity) 28.稳定度stability5.单位可靠性29.reliability unit(of measurement)6.hysteresis 30.回程测量measurement7.测试measurement and test 漂移31.drift8.response time 响应时间检验inspecte32.9.33.静态测量measuring force 测量力（简称“测力”）static measurement10. 几何量测量器具术语动态测量dynamic measurement11. 测量原理principle of measurement12.测量方法 1.几何量具测量器具method of measurement13.测量程序dimensional measuring instrumentsmeasurement procedure14.被测量length measuring instruments 2.长度测量器具measurand15.影响量influence quantity角度测量器具3.angle measuring instruments16.变换值transformed value(of a measurand) coordinate measuring machine4.坐标测量机17.测量信号error and 形状和位置误差测量器具5.form position measurement signal18.直接测量法direct method of measurement measuring instruments19.间接测量法indirect method of measurement 6.表面质量测量器具20.surface quality measuring instruments 定义测量法definitive method of measurement21.gear measuring instruments 齿轮测量器具直接比较测量法 7.direct-comparison method of measurement）material measure 实物量具（简称“量具”8.22.替代测量法substitution measuring instruments 测量仪器（简称“量仪”9.）method of measurement23.微差测量法differential measuring chain 测量链10.method of measurement24.零位测量法nulll method of measurement measuring system 测量装置11.25.测量结果指示式测量仪器12.result of a measurementmeasured value测得值26.indicating(measuring )instrument27.实际值actual value 15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion 28.未修正结果machining surfaces （of a measurement） uncorrected result16.表面粗糙度比较样块抛光加工表面measurement) 29.已修正结果corrected result(of a roughness 30.测量的准确度accuracy of measurementcomparison specimens pollshed surfaces17.接触式仪器的标称特性 31.测量的重复性repeatability of measurement18.轮廓reproducibility of measurements profiles32.测量复现性19.实验标准偏差轨迹轮廓experimental standard deviation traced profile33.20.34.测量不确定度uncertainty of measurement 基准轮廓 reference profile21.总轮廓35.测量绝对误差 absolute error of measurement total profile22.原始轮廓相对误差36. relative error primary profile23.残余轮廓37.随机误差random errorresidual profile24.触针式仪器stylus instrument38.系统误差 systematic error25.感应位移数39.修正值correction字存储触针式量仪displacementsensitive,digitally storing stylus instrument 修正系数40.correction factor26.触针式仪器的部件stylus personal error41.人员误差instrument components27.environmental error 测量环measurement loop 环境误差42.28.导向基准renfence guide 43.方法误差error of method29.驱动器drive unit调整误差44.adjustment error30.测头(传感器)probe(pick-up) reading error 45.读数误差31.拾取单元tracing element 46.视差parallax error32.针尖 interpolation error 47.估读误差stylus tip33.parasitic error 转换器transducer 粗大误差48.34.49.检定放大器amplifier verification35.模校准50.calibration /数转换器analog-to-digital converter36.数据输入51.调准gauging data input37.adjustment数据输出data output 调整52.38.:knife straigjht edge 刀口型直尺轮廓滤波和评定1.profile filtering and evaluation2.刀口尺: knife straigjht edge39.轮廓记录器profile recorder three edges straigjht edge 3.三棱尺40.four edges straigjht edge 仪器的计量特性四棱尺4.metrological characteristics of the instrument 条式和框式水平仪 5.41.静测力的变化change bar form and square levelsof static measuring force42.静态测力 imaging level meter 6.合像水平仪 static measuring force43.动态测量力 dynamic measuring force 铸铁平板7 cast iron surface plate44.滞后 granite surface plate 岩石平板8.hysteresis45.测头的测量范围 cast iron straigjht edge 铸铁平尺9.transmission function for the sine waves 10.钢平尺和岩石平尺46.steel and granite straigjht edge仪器的测量范围measuring range of the instrument 圆度仪11. roundness measuring instrument47.模数转换器的量化步距电子水平仪12.electronic level meterquantization step of the ADC表面粗糙度比较样块铸造表面13.48.仪器分辨力 instrument resolutionroughness comparison specimens cast surface49.量程分辨力比表面粗糙度比较样块磨、车、铣、插及刨加工表面14.range-to-resolution ratioRoughness comparisonspecimens-ground, turned, 50.测头线性偏差probe linearity deviation 短波传输界限51.,shape and planed bored,milledshort-wave transmission limitation 76工作螺纹量规work gauges for metric trapezoidal screw threads 52.轮廓垂直成分传输77校对螺纹量规vertical profile component transmission check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸表面粗糙度比较样块抛丸、喷砂加工表面53 Types anddimensionsof metric trapezoidal screw threadsroughness comparison specimens shot blasted and79.普通螺纹量规型式与尺寸blasted surfacesTypes and dimensionsof gauges purpose screw threads54产品结构几何量计术规范80.非螺纹密封的管螺纹量GPS（）geometrical product specifications(GPS) 规 Gauges for pipethreads prcessure-tight joints are not made on the 55表面结构 surface texture threads接触式仪器的标称特性 nominal characteristics 5681.of contact instruments螺纹千分尺Screw thread micrometer57公法线千分尺micrometer for mearsuring root82.最大允许误差tangent lenghths of gear teethmaximum permissible error83.间隙螺纹量规 maximum permissible error58最大允许误差 Clearance screw gauge84.量针圆柱直齿渐开线花键量规 gauges for straight Bar gauge5985.cylindrical involute splines螺纹样板 Screw thread template86. Gear tooth vernier calipers 用螺纹密封的管螺纹量规 60齿厚游标卡尺Gauges for pipe threads where pressure-tight 齿轮渐开线样板the involute master of gear 61joints are made on the threads 62齿轮螺旋线样板 the helix master of gear87.刀具预调测量仪 sided straight 规键形63矩花量 gauges for –精度Accuracy of the presetting instrument splines88.64测量蜗杆 master worm 薄膜式气动量仪Membrane type pneumatic measuring instrument 万能测齿仪6589.光栅线位移测量系统universal gear measuring instrumentGrating linear displacement measuring system 万能渐开线检查仪6690.光栅角位移测量系统universal involute measuring instrumentGrating angular displacement measuring system 齿轮齿距测量仪6791.磁栅线位移测量系统 gear circular pictch measuring instrumentMagnet-grid linear displacement measuring 万能齿轮测量机68 system92.量块附件 Universal gear measuring machineAccessories for gauge blocks 齿轮螺旋线测量仪6993.Vgear helix measuring instrument 形架Vee blocks 便携式齿轮齿距测量仪7094.manual gear circular pitch measuring instrument 比较仪座Comparator stand 71 便携式齿轮基节测量仪95.manual gear base pitch measuring instrument 磁性表座Magnetic stand 立式滚刀测量仪7296.万能表座 vertical hob measuring instrument Universal stand for dial indicator 齿轮双面啮合综合测量仪73Gear dual-flank measuring instrument1. 齿轮单面啮合整体误差测量仪74刀口型直尺:knife straigjht edge2.刀口尺Gear single-flank meshing integrated error : knife straigjht edge3.measuring instrument 三棱尺three edges straigjht edge4.75四棱尺four edges straigjht edge梯形螺纹量规bar form and square levels条式和框式水平仪5.gauges for metric trapezoidal screw threads6.合像水平仪imaging level meter 41.静测力的变化change of static measuring force42.7铸铁平板cast iron surface plate 静态测力static measuring force43.动态测量力dynamic measuring force 8.岩石平板granite surface plate44.滞后9.铸铁平尺cast iron straigjht edgehysteresis45.steel and granite straigjht 测头的测量范围transmission function for the 10.钢平尺和岩石平尺sine wavesedge46.仪器的测量范围圆度仪11.roundness measuring instrument measuring range of the instrumentelectronic level meter12.电子水平仪47.模数转换器的量化步距造粗13.表面糙度比较样块铸表面roughness quantization step of theADCcomparison specimens cast surface48.仪器分辨力instrument resolution14.表面粗糙度比较样块磨、车、铣、插及刨加工表面49.量程分辨力比range-to-resolution ratio comparison roughness50.测头线性偏差and probe linearity deviationspecimens-ground,turned,bored,milled,shape51.planed短波传输界限short-wave transmissionlimitation表面粗糙度比较样块电火花加工表面roughness 15.52.spark-erostion machining 轮廓垂直成分传输vertical profile component specimens comparisontransmission1surfaces53表面粗糙度比较样块抛丸、喷砂加工表面16.表面粗糙度比较样块抛光加工表面roughness roughnesscomparison specimens shot comparison specimens pollshed surfaces blasted and blasted surfaces17.接触式仪器的标称特性54轮廓18.profiles产品结构几何量计术规范(GPS)geometricalproduct specifications(GPS) 轨迹轮廓traced profile 19.5520.表面结构surface texture 基准轮廓reference profile56接触式仪器的标称特性nominal characteristics 21.总轮廓total profileof contact instrumentsprimary profile 原始轮廓22.57公法线千分尺micrometer for mearsuring root residualprofile 23.残余轮廓tangent lenghths of gear teethstylus instrument触针式仪器24.58仪最大允许误差displacement maximum permissible error量针储字移应25.感位数存触式59sensitive,digitally storing stylus instrument 圆柱直齿渐开线花键量规gauges for straightcylindrical involute splinescomponents stylus 26.触针式仪器的部件instrument60齿厚游标卡尺测量环27.measurement loop Gear tooth vernier calipers6128.齿轮渐开线样板renfence guide 导向基准the involute master of gear62驱动器29.drive unit齿轮螺旋线样板the helix master of gear63传感器(30.测头矩形花键量规) probe(pick-up)gauges for straight拾取单元31.tracing element –sided splines64测量蜗杆stylus tip 32.针尖master worm65万能测齿仪转换器33.transducer universal gear measuring instrument6634.amplifier放大器万能渐开线检查仪universal involute measuringinstrument35./模数转换器analog-to-digital converter6736.data input 数据输入齿轮齿距测量仪gear circular pictchmeasuring instrument 37.data output 数据输出6838. 轮廓滤波和评定万能齿轮测量机Universal gear measuring machine profile filtering and evaluation69profile recorder轮廓记录器39.齿轮螺旋线测量仪gear helix measuring instrument 仪器的计量特性40.metrological characteristics便携式齿轮齿距测量仪70of the instrumentmanual gear circular pitch measuring instrument71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flankmeshing integrated error measuring instrument75梯形螺纹量规gauges for metric trapezoidalscrew threads76工作螺纹量规work gauges for metric trapezoidalscrew threads77校对螺纹量规check gauges for metrictrapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensionsof metric trapezoidal screw threads79.普通螺纹量规型式与尺寸Types and dimensionsof gauges purpose screw threads80.非螺纹密封的管螺纹量规Gauges for pipethreads prcessure-tight joints are not made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差maximum permissible error83.间隙螺纹量规Clearance screw gauge84.量针Bar gauge85.螺纹样板Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipethreads where pressure-tight joints are made on the threads87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic standUniversal stand for dial indicator 万能表座96.。
量具量仪中英文对照
67齿轮齿距测量仪gear circular pictch measuring instrument
68万能齿轮测量机 Universal gear measuring machine
69齿轮螺旋线Biblioteka 量仪gear helix measuring instrument
值transformed value(of a measurand)
17. 测量信号measurement signal
18. 直接测量法direct method of measurement
19. 间接测量法indirect method of measurement
Gauges for pipe threads where pressure-tight joints are made on the threads
87.刀具预调测量仪 精度
Accuracy of the presetting instrument
88.薄膜式气动量仪
Membrane type pneumatic measuring instrument
58最大允许误差 maximum permissible error
59圆柱
直齿渐开线花键量规 gauges for straight cylindrical involute splines
60齿厚游标卡尺 Gear tooth vernier calipers
92.量块附件
Accessories for gauge blocks
93.V形架
Vee blocks
量具中英文对照
量具Measuring Tools 计量Gauging卡尺――Caliper 0.02游标卡尺－――Vernier Caliper数显卡尺――Digital Caliper带表卡尺――Digital Slide Caliper CA=Calipers卡尺深度尺――depth gauge 0.02数显深度尺――Digital depth gauge 外径深度尺――depth micrometerDI=Depth Indicator深度测试仪千分尺micrometer 0.01外径千分尺――external micrometer, 外径千分尺outside micrometer内径千分尺――Internal micrometer内径千分尺micrometer inside caliper;inside micrometer 深度千分尺micrometer depth gauge; depth micrometer卡钳式内径千分尺－Internal quick caliper dial gauge外径千分尺标准棒――micrometer standard外径千分尺架子――micrometer stand带表外径千分尺――Indicator dial micrometer MI=Micrometer千分尺千分表-Dial indicator数显千分表-Digital indicator千分表外径规―――Dial indicator snap gauges平面规surface gauge磁性吸座－－Magnetic stand孔的轮廓量规－Bore profile gauge KT点接触杠杆千分表---Lever dial indicator point contact length可调的磁力架----Magnetic stand with fine adjustment高度尺height gauge 0.02游标高度尺---Vernier height gauge数显游标高度尺Digital height gaugeMH=Height tester高度测试仪尺规\刀规－Straight edge板规plate gauge中心规centre gauge锥度规taper gauge比例规proportional dividers标准规standard gauge齿轮规gear tooth gauge分线规divider;dividers工作量规working gauge厚薄规feeler(gauge)角规angle gauge块规gauge(block)量规gauge螺距规screw pitch gauge螺纹千分尺screw micrometer内卡钳inside caliper外卡钳outside caliper圆规compasses椭圆规ellipsograph隙规gap(/clearance) gauge线规wire gauge斜角规bevel square折尺folding pocket measure(/ruler)曲尺carpenter’s square钢尺――steel rule刻度尺graduation ruler丁字尺T-square三角尺set square直尺straight edge皮尺tape(/measure)卷尺Locking tape measure金属卷尺metallic tape角尺――angle square组合角尺combination set花岗岩平台（精度1极）Granite table, accuracy 1装有T型槽的平台-Tenon and T-slot incl. InstallationGage计量器Dial Bore 3 Point Gauge 0.01 三点内径百分表Plug 止通棒Go No/Go Plug PG=pin Gauge针规VISUAL 目测BARE-EYEDial Caliper刻度卡尺Dial Indicator 0.01百分表ID Groove Gage内沟槽尺Thread Gage螺纹止通规Plug Guage塞规TRIMIC三点内测千分尺CMM三坐标检测ROUGHNESS GAGE粗糙度样板R=Rough of surface tester表面粗糙测试仪Profile Projector投影仪PJ=Profile projector侧面投影仪CM=Coordinate measuring machine协调测量机器VM=Vision measuring machine目测机器TM=Tool microscope显微镜EW=Electron Weigh电子称。
计量器具中英文对照
1. 量块gaugeblock2. 光滑极限量规plainlimit gauge3. 塞规pluggauge4. 环规ringgauge卡规snap gauge5. 塞尺feelergauge6. 钢直尺steelgauge7. 精密玻璃线纹尺precision glass linear scale8. 精密金属线纹尺precision metal linear scale9. 半径样板radiustemplate卡尺类1. 游标卡尺verniercaliper2. 带表卡尺dialcaliper3. 电子数显卡尺calliperwith electronic digital display4. 深度标游卡尺depthvernier caliper5. 电子数显深度卡尺depthcaliper with electronic digital display6. 带表高度卡尺dialheight calliper7. 高度游标卡尺heightvernier caliper8. 电子数显高度卡尺heightcaliper with electronic digital9. 焊接检验尺calliperfor welding inspection千分尺类1. 测微头micrometerhead2. 外径千分尺externalmicrometer3. 杠杆千分尺micrometer with dial comparator4. 带计数器千分尺micrometer with counter5. 电子数显外径千分尺micrometer with electronic digital display6. 小测头千分尺smallanvil micrometer7. 尖头千分尺pointmicrometer8. 板厚千分尺sheetmetal micrometer9. 壁厚千分尺tubemicrometer10. 叶片千分尺blademicrometer11. 奇数沟千分尺oddfluted micrometer12. 深度千分尺depthmicrometer13. 内径千分尺internalmicrometer14. 单杆式内径千分尺single-body internal micrometer15. 表式内径千分尺dailinternal micrometer16. 三爪式内径千分尺threepoint internal micrometer17. 电子数显三爪式内径千分尺three point internal micrometer18. 内测千分尺insidemicrometer指示表类1. 指示表dialindicator2. 深度只是表depthdialindicator3. 杠杆指示表dialtestindicator4. 内径指示表boredialindicator5. 涨弹簧式指示表expanding head bore dial indicator6. 钢球式内径指示表balltype bore dial indicator7. 电子数显指示表dialindicator with electronic digital display8. 杠杆卡规indicatingsnap gauge9. 带表卡规dialsnapgauge10. 带表外卡规outsidedial snap gauge11. 带表内卡规insidedial snap gauge12. 测厚规thicknessgauge13. 扭簧比较仪microcator14. 杠杆齿轮比较仪mechanical dial comparator15. 电子量规electronicgauge16. 电感式传感器inductance type transducer17. 指示装置indicatingdevice18. 电感测微仪inductance micrometer19. 峰值电感测微仪peakinductance micrometer20. 电感内径比较仪inductance bore comparator21. 瞄准传感器aimingtransducer角度测量器具1. 角度块angleblockgauge2. 正多面棱体regularpolygon mirror3. 刀具角度样板cutterangular template4. 直角尺square5. 平行直角尺parallelsquare6. 宽座直角尺wide-stand square7. 刀口形直角尺edgesquare8. 矩形直角尺squaresquare9. 三角形直角尺threeangle square10. 圆柱直角尺cylindersquare11. 方形角尺squareguage12. 万能角度尺universalbevel protractor13. 游标式万能角度尺vernier universal bevel protractor14. 表式万能角度尺dialuniversal bevel protractor15. 光学分度头opticaldividing head16. 目镜式光学分度头optical dividing head with microscope reading17. 投影式光学分度尺optical dividing head with projection reading18. 光电分度头optical-electronic dividing head19. 多齿分度台multi-tooth division table20. 分度转台divisionrotary table21. 正炫规sinebar22. 普通正炫规generalsine bar23. 铰链式正炫规hingetype sine bar24. 双向正炫规dual-directional sine bar25. 圆锥量规conegauge26. 圆锥塞规plugconegauge27. 圆锥环规ringconegauge28. 直角尺测量仪squaremeasuring instrument 计量器具中英文对照汇总表-形位误差测量器具1. 平晶opticalflat2. 单面平晶opticalflat3. 双面平晶paralleloptical flat4. 刀口形直尺knifestraight edge5. 刀口尺knifestraight edge6. 三棱尺threeedgesstraight edge7. 四棱尺fouredgesstraight edge8. 平尺straightedge9. 矩形平尺squarestraight edge10. 工字形平尺i-beamstraight edge11. 角形平尺anglestraight edge12. 桥形平尺bridgetypestraight edge13. 平板surfaceplate14. 铸铁平板castironsurface plate15. 岩石平板granitesurface plate16. 方箱squarebox17. 水准器式水平仪levelmeter18. 条式水平仪barlevelmeter19. 框式水平仪framelevel meter20. 合像水平仪imaginglevel meter21. 光学倾斜仪opticalinclinometer22. 电子水平仪electronic level meter23. 指针式电子水平仪electronic level meter with indicator24. 数显式电子水平仪electronic level meter with digital display25. 平直度测量仪straightness measuring instrument26. 光学式平直度测量仪optical straightness measuring instrument27. 光电式平直度测量仪photoelectrical straightnessmeasuringinstrument28. 圆度测量仪roundnessmeasuring instrument29. 转轴式圆度测量仪spindle-rotating type roundnessmeasuringinstrument30. 转台式圆度测量仪table-rotating type roundnessmeasuringinstrument计量器具中英文对照汇总表1.刀口型直尺:knifestraigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪imaging level meter7铸铁平板cast iron surface plate8.岩石平板granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens castsurf ace14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparison specimens-ground,turned,bored,milled,shapeandpla ned15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machiningsurfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓traced profile20.基准轮廓reference profile21.总轮廓total profile22.原始轮廓primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storin gstylusinstrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profile filtering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument41.静测力的变化change of static measuring force42.静态测力static measuring force43.动态测量力dynamic measuring force44.滞后hysteresis45.测头的测量范围transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输vertical profile component transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blastedsurfaces54产品结构几何量计术规范（GPS）geometricalproduct specifications(GPS) 55表面结构surface texture56接触式仪器的标称特性nominal characteristics of contact instruments 57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差maximum permissible error59圆柱直齿渐开线花键量规gauges for straight cylindricalinvolute splines60齿厚游标卡尺Gear tooth verniercalipers61齿轮渐开线样板the involute master of gear62齿轮螺旋线样板the helix master of gear63矩形花键量规gauges for straight –sided splines64测量蜗杆master worm65万能测齿仪universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument70便携式齿轮齿距测量仪manual gear circular pitch measuring instrument 71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integratederrormeasuring instrument75梯形螺纹量规gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensions of metric trapezoidalscrewthreads79.普通螺纹量规型式与尺寸Types and dimensions of gauges purposescrewthreads80.非螺纹密封的管螺纹量规Gauges for pipe threadsprcessure-tight joints arenot made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差maximum permissible error83.间隙螺纹量规Clearance screw gauge84.量针Bar gauge85.螺纹样板Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made onthethreads 87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator计量器具中英文对照汇总表一般术语：1. 几何测量geometrical product2. 量值value(ofaquantity)3. 真值truevalue(ofa quantity)4. 约定真值conventional true value(of aquantity)5. 单位unit(ofmeasurement)6. 测量measurement7. 测试measurementand test8. 检验inspecte9. 静态测量staticmeasurement10. 动态测量dynamicmeasurement11. 测量原理principleof measurement12. 测量方法methodofmeasurement13. 测量程序measurement procedure14. 被测量measurand15. 影响量influencequantity16. 变换值transformedvalue(of a measurand)17. 测量信号measurement signal18. 直接测量法directmethod of measurement19. 间接测量法indirectmethod of measurement20. 定义测量法definitive method of measurement21. 直接比较测量法direct-comparison method of measurement22. 替代测量法substitution method of measurement23. 微差测量法differential method of measurement24. 零位测量法nulllmethod of measurement25. 测量结果result ofameasurement26. 测得值measuredvalue27. 实际值actualvalue28. 未修正结果uncorrected result（ofameasurement）29. 已修正结果correctedresult(of a measurement)30. 测量的准确度accuracyof measurement31. 测量的重复性repeatability of measurement32. 测量复现性reproducibility of measurements33. 实验标准偏差experimental standard deviation34. 测量不确定度uncertainty of measurement35. 测量绝对误差absoluteerror of measurement36. 相对误差relativeerror37. 随机误差randomerror38. 系统误差systematicerror39. 修正值correction40. 修正系数correctionfactor41. 人员误差personalerror42. 环境误差environmental error43. 方法误差errorofmethod44. 调整误差adjustmenterror45. 读数误差readingerror46. 视差parallaxerror47. 估读误差interpolation error48. 粗大误差parasiticerror49. 检定verification50. 校准calibration51. 调准gauging52. 调整adjustment计量器具中英文对照汇总表-几何量测量器具术语1. 几何量具测量器具dimensional measuring instruments2. 长度测量器具lengthmeasuring instruments3. 角度测量器具anglemeasuring instruments4. 坐标测量机coordinate measuring machine5. 形状和位置误差测量器具form and position error measuring instruments6. 表面质量测量器具surface quality measuring instruments7. 齿轮测量器具gearmeasuring instruments8. 实物量具（简称“量具”）materialmeasure9. 测量仪器（简称“量仪”）measuringinstruments10. 测量链measuringchain11. 测量装置measuringsystem12. 指示式测量仪器indicating(measuring )instrument13. 记录式测量仪器recording（measuring）instrument14. 累计式测量仪器totalizing(measuring)instrument15. 积分式测量仪器integrating(measuring)instrument16. 模拟式测量仪器analogue(measuring)instrument17. 数字式测量仪器digital(measuring)instrument18. 测量变换器measuringtransducer19. 传感器sensor20. 指示装置indicatingdevice21. 记录装置recordingdevice22. 记录载体recordingmedium23. 标尺标记scalemark24. 指示器index25. 标尺scale26. 度盘dail计量器具中英文对照汇总表-测量器具术语1. 标称值nominalvalue2. 示值indication(of a measuring instrument)3. 标尺范围scalerange4. 标称范围nominalrange5. 标尺长度scalelength6. 标尺分度scaledivision7. 分度值value ofascale division8. 标尺间距scalespacing9. 线性标尺linearscale10. 非线性标尺non-linear scale11. 标尺标数scalenumbering12. 测量仪器的零位zeroofa measuring instrument13. 量程span14. 测量范围measuringrange15. 额定工作条件vatedoperating conditions16. 极限条件referencecondition17. 标准条件referencecondition18. 仪器常数instrumentconstant19. 响应特性responsecharacteristic20. 灵敏度senstivity21. 鉴别力discrimination22. 分辨力resolution（ofanindicating device）23. 死区deadband24. 准确度accuracyofa measuring instruments25. 准确度等级accuracyclass26. 重复性repeatability of a measuring instrument27. 示值变动性varationof indication28. 稳定度stability29. 可靠性reliability30. 回程hysteresis31. 漂移drift32. 响应时间responsetime33. 测量力（简称“测力”）measuringforce计量器具中英文对照汇总表-测量器具术语1. 实物量具示值误差errorof indication of a material measure2. 测量仪器示值误差errorof indication of a measuring instrument3. 重复性误差repeatability error of a measuring instrument4. 回程误差hysteresiserror5. 测量力变化variationof measuring force6. 测量力落差hysteresis of measuring force7. 偏移误差biaserror(of a measuring instrument)8. 允许误差maximumpermissible errors(of measuringinstruments)9. 跟踪误差trackingerror (of a measuring instrument)10. 响应率误差response-law error (of a measuring instrument)11. 量化误差quantization error (of a measuring instrument)12. 基值误差datumerror(of a measuring instrument)13. 零值误差zeroerror(of a measuring instrument)14. 影响误差influenceerror15. 引用误差fiducialerror16. 位置误差positionerror17. 线性误差linearerror18. 响应特性曲线responsecharacteristic curve19. 误差曲线errorcurve20. 校准曲线calibration curve21. 修正曲线correctioncurve计量器具中英文对照汇总表-表面质量测量器具表面粗糙度比较样块surface roughness comparison specimen铸造表面粗糙度比较样块surface roughness comparison specimen forcastsurface磨、车、镗、铣、插及刨加工表面粗糙度比较样块surface roughness comparison specimenforground,turned,bored,milled,shaped andplanedsurface电火花加工表面粗糙度比较样块surface roughness comparison specimenforspark-erosion machined surface抛（喷）丸、喷砂加工表面粗糙度比较样块surface roughness comparison specimen forshotblasted and grit blasted surface抛光加工表面粗糙度测量仪portable surface roughness comparison specimenforpolished surface便携式表面粗糙度测量仪portable surface roughessmeasuringinstrument驱动箱drivingbox台式表面粗糙度测量仪bench type surface roughnessmeasuringinstrument。
计量器具中英文对照
1. 量块gaugeblock2. 光滑极限量规plainlimit gauge3. 塞规pluggauge4. 环规ringgauge卡规snap gauge5. 塞尺feelergauge6. 钢直尺steelgauge7. 精密玻璃线纹尺precision glass linear scale8. 精密金属线纹尺precision metal linear scale9. 半径样板radiustemplate卡尺类1. 游标卡尺verniercaliper2. 带表卡尺dialcaliper3. 电子数显卡尺calliperwith electronic digital display4. 深度标游卡尺depthvernier caliper5. 电子数显深度卡尺depthcaliper with electronic digital display6. 带表高度卡尺dialheight calliper7. 高度游标卡尺heightvernier caliper8. 电子数显高度卡尺heightcaliper with electronic digital9. 焊接检验尺calliperfor welding inspection千分尺类1. 测微头micrometerhead2. 外径千分尺externalmicrometer3. 杠杆千分尺micrometer with dial comparator4. 带计数器千分尺micrometer with counter5. 电子数显外径千分尺micrometer with electronic digital display6. 小测头千分尺smallanvil micrometer7. 尖头千分尺pointmicrometer8. 板厚千分尺sheetmetal micrometer9. 壁厚千分尺tubemicrometer10. 叶片千分尺blademicrometer11. 奇数沟千分尺oddfluted micrometer12. 深度千分尺depthmicrometer13. 内径千分尺internalmicrometer14. 单杆式内径千分尺single-body internal micrometer15. 表式内径千分尺dailinternal micrometer16. 三爪式内径千分尺threepoint internal micrometer17. 电子数显三爪式内径千分尺three point internal micrometer18. 内测千分尺insidemicrometer指示表类1. 指示表dialindicator2. 深度只是表depthdialindicator3. 杠杆指示表dialtestindicator4. 内径指示表boredialindicator5. 涨弹簧式指示表expanding head bore dial indicator6. 钢球式内径指示表balltype bore dial indicator7. 电子数显指示表dialindicator with electronic digital display8. 杠杆卡规indicatingsnap gauge9. 带表卡规dialsnapgauge10. 带表外卡规outsidedial snap gauge11. 带表内卡规insidedial snap gauge12. 测厚规thicknessgauge13. 扭簧比较仪microcator14. 杠杆齿轮比较仪mechanical dial comparator15. 电子量规electronicgauge16. 电感式传感器inductance type transducer17. 指示装置indicatingdevice18. 电感测微仪inductance micrometer19. 峰值电感测微仪peakinductance micrometer20. 电感内径比较仪inductance bore comparator21. 瞄准传感器aimingtransducer角度测量器具1. 角度块angleblockgauge2. 正多面棱体regularpolygon mirror3. 刀具角度样板cutterangular template4. 直角尺square5. 平行直角尺parallelsquare6. 宽座直角尺wide-stand square7. 刀口形直角尺edgesquare8. 矩形直角尺squaresquare9. 三角形直角尺threeangle square10. 圆柱直角尺cylindersquare11. 方形角尺squareguage12. 万能角度尺universalbevel protractor13. 游标式万能角度尺vernier universal bevel protractor14. 表式万能角度尺dialuniversal bevel protractor15. 光学分度头opticaldividing head16. 目镜式光学分度头optical dividing head with microscope reading17. 投影式光学分度尺optical dividing head with projection reading18. 光电分度头optical-electronic dividing head19. 多齿分度台multi-tooth division table20. 分度转台divisionrotary table21. 正炫规sinebar22. 普通正炫规generalsine bar23. 铰链式正炫规hingetype sine bar24. 双向正炫规dual-directional sine bar25. 圆锥量规conegauge26. 圆锥塞规plugconegauge27. 圆锥环规ringconegauge28. 直角尺测量仪squaremeasuring instrument 计量器具中英文对照汇总表-形位误差测量器具1. 平晶opticalflat2. 单面平晶opticalflat3. 双面平晶paralleloptical flat4. 刀口形直尺knifestraight edge5. 刀口尺knifestraight edge6. 三棱尺threeedgesstraight edge7. 四棱尺fouredgesstraight edge8. 平尺straightedge9. 矩形平尺squarestraight edge10. 工字形平尺i-beamstraight edge11. 角形平尺anglestraight edge12. 桥形平尺bridgetypestraight edge13. 平板surfaceplate14. 铸铁平板castironsurface plate15. 岩石平板granitesurface plate16. 方箱squarebox17. 水准器式水平仪levelmeter18. 条式水平仪barlevelmeter19. 框式水平仪framelevel meter20. 合像水平仪imaginglevel meter21. 光学倾斜仪opticalinclinometer22. 电子水平仪electronic level meter23. 指针式电子水平仪electronic level meter with indicator24. 数显式电子水平仪electronic level meter with digital display25. 平直度测量仪straightness measuring instrument26. 光学式平直度测量仪optical straightness measuring instrument27. 光电式平直度测量仪photoelectrical straightnessmeasuringinstrument28. 圆度测量仪roundnessmeasuring instrument29. 转轴式圆度测量仪spindle-rotating type roundnessmeasuringinstrument30. 转台式圆度测量仪table-rotating type roundnessmeasuringinstrument计量器具中英文对照汇总表1.刀口型直尺:knifestraigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪imaging level meter7铸铁平板cast iron surface plate8.岩石平板granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens castsurf ace14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparison specimens-ground,turned,bored,milled,shapeandpla ned15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machiningsurfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓traced pro.基准轮廓reference pro.总轮廓total pro.原始轮廓primary pro.残余轮廓residual pro.触针式仪器stylus instrument 25.感应位移数字存储触针式量仪displacement sensitive,digitally storin gstylusinstrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定pro and evaluation39.轮廓记录器pro40.仪器的计量特性metrological characteristics of the instrument41.静测力的变化change of static measuring force42.静态测力static measuring force43.动态测量力dynamic measuring force44.滞后hysteresis45.测头的测量范围transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输vertical pro transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blastedsurfaces54产品结构几何量计术规范（GPS）geometricalproduct specifications(GPS) 55表面结构surface texture56接触式仪器的标称特性nominal characteristics of contact instruments 57公法线千分尺micrometer for mearsuring root tangent lenghths of gearteeth58最大允许误差maximum permissible error59圆柱直齿渐开线花键量规gauges for straight cylindricalinvolute splines60齿厚游标卡尺Gear tooth verniercalipers61齿轮渐开线样板the involute master of gear62齿轮螺旋线样板the helix master of gear63矩形花键量规gauges for straight –sided splines64测量蜗杆master worm65万能测齿仪universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument70便携式齿轮齿距测量仪manual gear circular pitch measuring instrument 71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integratederrormeasuring instrument75梯形螺纹量规gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensions of metric trapezoidalscrewthreads79.普通螺纹量规型式与尺寸Types and dimensions of gauges purposescrewthreads80.非螺纹密封的管螺纹量规Gauges for pipe threadsprcessure-tight joints arenot made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差maximum permissible error83.间隙螺纹量规Clearance screw gauge84.量针Bar gauge85.螺纹样板Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made onthethreads 87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator计量器具中英文对照汇总表一般术语：1. 几何测量geometrical product2. 量值value(ofaquantity)3. 真值truevalue(ofa quantity)4. 约定真值conventional true value(of aquantity)5. 单位unit(ofmeasurement)6. 测量measurement7. 测试measurementand test8. 检验inspecte9. 静态测量staticmeasurement10. 动态测量dynamicmeasurement11. 测量原理principleof measurement12. 测量方法methodofmeasurement13. 测量程序measurement procedure14. 被测量measurand15. 影响量influencequantity16. 变换值transformedvalue(of a measurand)17. 测量信号measurement signal18. 直接测量法directmethod of measurement19. 间接测量法indirectmethod of measurement20. 定义测量法definitive method of measurement21. 直接比较测量法direct-comparison method of measurement22. 替代测量法substitution method of measurement23. 微差测量法differential method of measurement24. 零位测量法nulllmethod of measurement25. 测量结果result ofameasurement26. 测得值measuredvalue27. 实际值actualvalue28. 未修正结果uncorrected result（ofameasurement）29. 已修正结果correctedresult(of a measurement)30. 测量的准确度accuracyof measurement31. 测量的重复性repeatability of measurement32. 测量复现性reproducibility of measurements33. 实验标准偏差experimental standard deviation34. 测量不确定度uncertainty of measurement35. 测量绝对误差absoluteerror of measurement36. 相对误差relativeerror37. 随机误差randomerror38. 系统误差systematicerror39. 修正值correction40. 修正系数correctionfactor41. 人员误差personalerror42. 环境误差environmental error43. 方法误差errorofmethod44. 调整误差adjustmenterror45. 读数误差readingerror46. 视差parallaxerror47. 估读误差interpolation error48. 粗大误差parasiticerror49. 检定verification50. 校准calibration51. 调准gauging52. 调整adjustment计量器具中英文对照汇总表-几何量测量器具术语1. 几何量具测量器具dimensional measuring instruments2. 长度测量器具lengthmeasuring instruments3. 角度测量器具anglemeasuring instruments4. 坐标测量机coordinate measuring machine5. 形状和位置误差测量器具form and position error measuring instruments6. 表面质量测量器具surface quality measuring instruments7. 齿轮测量器具gearmeasuring instruments8. 实物量具（简称“量具”）materialmeasure9. 测量仪器（简称“量仪”）measuringinstruments10. 测量链measuringchain11. 测量装置measuringsystem12. 指示式测量仪器indicating(measuring )instrument13. 记录式测量仪器recording（measuring）instrument14. 累计式测量仪器totalizing(measuring)instrument15. 积分式测量仪器integrating(measuring)instrument16. 模拟式测量仪器analogue(measuring)instrument17. 数字式测量仪器digital(measuring)instrument18. 测量变换器measuringtransducer19. 传感器sensor20. 指示装置indicatingdevice21. 记录装置recordingdevice22. 记录载体recordingmedium23. 标尺标记scalemark24. 指示器index25. 标尺scale26. 度盘dail计量器具中英文对照汇总表-测量器具术语1. 标称值nominalvalue2. 示值indication(of a measuring instrument)3. 标尺范围scalerange4. 标称范围nominalrange5. 标尺长度scalelength6. 标尺分度scaledivision7. 分度值value ofascale division8. 标尺间距scalespacing9. 线性标尺linearscale10. 非线性标尺non-linear scale11. 标尺标数scalenumbering12. 测量仪器的零位zeroofa measuring instrument13. 量程span14. 测量范围measuringrange15. 额定工作条件vatedoperating conditions16. 极限条件referencecondition17. 标准条件referencecondition18. 仪器常数instrumentconstant19. 响应特性responsecharacteristic20. 灵敏度senstivity21. 鉴别力discrimination22. 分辨力resolution（ofanindicating device）23. 死区deadband24. 准确度accuracyofa measuring instruments25. 准确度等级accuracyclass26. 重复性repeatability of a measuring instrument27. 示值变动性varationof indication28. 稳定度stability29. 可靠性reliability30. 回程hysteresis31. 漂移drift32. 响应时间responsetime33. 测量力（简称“测力”）measuringforce计量器具中英文对照汇总表-测量器具术语1. 实物量具示值误差errorof indication of a material measure2. 测量仪器示值误差errorof indication of a measuring instrument3. 重复性误差repeatability error of a measuring instrument4. 回程误差hysteresiserror5. 测量力变化variationof measuring force6. 测量力落差hysteresis of measuring force7. 偏移误差biaserror(of a measuring instrument)8. 允许误差maximumpermissible errors(of measuringinstruments)9. 跟踪误差trackingerror (of a measuring instrument)10. 响应率误差response-law error (of a measuring instrument)11. 量化误差quantization error (of a measuring instrument)12. 基值误差datumerror(of a measuring instrument)13. 零值误差zeroerror(of a measuring instrument)14. 影响误差influenceerror15. 引用误差fiducialerror16. 位置误差positionerror17. 线性误差linearerror18. 响应特性曲线responsecharacteristic curve19. 误差曲线errorcurve20. 校准曲线calibration curve21. 修正曲线correctioncurve计量器具中英文对照汇总表-表面质量测量器具表面粗糙度比较样块surface roughness comparison specimen铸造表面粗糙度比较样块surface roughness comparison specimen forcastsurface磨、车、镗、铣、插及刨加工表面粗糙度比较样块surface roughness comparison specimenforground,turned,bored,milled,shaped andplanedsurface电火花加工表面粗糙度比较样块surface roughness comparison specimenforspark-erosion machined surface抛（喷）丸、喷砂加工表面粗糙度比较样块surface roughness comparison specimen forshotblasted and grit blasted surface抛光加工表面粗糙度测量仪portable surface roughness comparison specimenforpolished surface便携式表面粗糙度测量仪portable surface roughessmeasuringinstrument驱动箱drivingbox台式表面粗糙度测量仪bench type surface roughnessmeasuringinstrument。
量具中英文对照表
BEVEL PLANK SCREW PITCH GAGE
斜板 螺距规
中文 气动量规 角铁 量角器 棒规 卡尺 三坐标 比较图 粗糙度样板 等高块 组合坐标尺正弦规 指示表 牙模 内径量表 测隙规 量块 槽宽规 测长仪 高度尺 S.T.I螺纹规 检验平板 外径千分尺 千分尺校对棒 尖头千分尺 管壁千分尺 刀刃千分尺 杠杆千分尺 盘形千分尺 深度千分尺 轮毂千分尺 内径千分尺 三爪千分尺 千分表 百分表 光学投影仪 外径样板 百分式卡钳 光面塞规 平行块 角度规 R规/园角规 转台 粗糙度仪 光面环规 找边投影仪 专用检具 杠杆表 螺纹塞规 螺纹环规 大量程指示表 测温计 高度仪 刀口直角尺 伸缩规
English AIR GAGE ANGLE IRON ANGLE PLATE BAR GAGE CALIPER CMM COMPARATOR CHART ROUGHNESS CONTRAST CONTOUR GAGE BLOCK COMBINATION SQUARE SET COMPOUND SINE PLATE DROP INDICATOR DENTAL & MOLD DIAL BORE FEELET GAGE GAGE BLOCK GROOVE WIDTH GAGE GAGE MAKER HEIGHT GAGE HELI-COIL THD.PLUG INSPECTION PLATE O.D MICROMETER O.DMICROMETER STANDARDS O.D MICROMETER(SHARP OIINTED) O.D MICROMETER(TUBE ) O.D MICROMETER(BLADE) O.D MICROMETER(LEVER) O.D MICROMETER(DISK) O.D MICROMETER(DEPTH) O.D MICROMETER(HUBCAP) O.D MICROMETER（INSIDE） O.D MICROMETER（INTRA ） MB-.0001" MB-.0005" OPTICAL COMPARATOR O.D SET MASTER O.D TEST PLUG GAGE PARALLEL SET PROTRACTOR RADIUS GAGE ROTATE TABLE ROUGHNESS METER SET RINGE SIDE VIEW COMPARATOR SPECIAL GAGE TEST INDICATOR THREAD PLUG GAGE THREAD RING GAGE TRAVEL INDICATOR TEMPERATURE PROBES TRIMOS VERTICAL KNIFE-EDGE SQUARE TELESCOPING GAGES
量具中英文对照
量具中英文对照卡尺类1.游标卡尺vernier caliper2.带表卡尺dial caliper3.电子数显卡尺calliper with electronic digital display4.深度标游卡尺depth vernier caliper5.电子数显深度卡尺depth caliper with electronic digital display6.带表高度卡尺dial height calliper7.高度游标卡尺height vernier caliper8.电子数显高度卡尺height caliper with electronic digital display9.焊接检验尺calliper for welding inspection千分尺类1.测微头micrometer head2.外径千分尺external micrometer3.杠杆千分尺micrometer with dial comparator4.带计数器千分尺micrometer with counter5.电子数显外径千分尺micrometer with electronic digital display6.小测头千分尺small anvil micrometer7.尖头千分尺point micrometer8.板厚千分尺sheet metal micrometer9.壁厚千分尺tube micrometer10.叶片千分尺blade micrometer11.奇数沟千分尺odd fluted micrometer12.深度千分尺depth micrometer13.内径千分尺internal micrometer14.单杆式内径千分尺single-body internal micrometer15.表式内径千分尺 dail internal micrometer16.三爪式内径千分尺three point internal micrometer17.电子数显三爪式内径千分尺three point internal micrometer18.内测千分尺inside micrometer长度测量器具量具类1.量块gauge block2.光滑极限量规plain limit gauge3.塞规plug gauge4.环规ring gauge 卡规snap gauge5.塞尺feeler gauge6.钢直尺steel gauge7.精密玻璃线纹尺precision glass linear scale8.精密金属线纹尺precision metal linear scale9.半径样板radius template测量器具术语1.实物量具示值误差error of indication of a material measure2.测量仪器示值误差error of indication of a measuring instrument3.重复性误差repeatability error of a measuring instrument4.回程误差hysteresis error5.测量力变化variation of measuring force6.测量力落差hysteresis of measuring force7.偏移误差bias error (of a measuring instrument)8.允许误差maximum permissible errors(of measuring instruments)9.跟踪误差tracking error (of a measuring instrument)10.响应率误差response-law error (of a measuring instrument)11.量化误差quantization error (of a measuring instrument)12.基值误差datum error (of a measuring instrument)13.零值误差zero error (of a measuring instrument)14.影响误差influence error15.引用误差fiducial error16.位置误差position error17.线性误差linear error18.响应特性曲线response characteristic curve19.误差曲线error curve20.校准曲线calibration curve21.修正曲线correction curve测量器具术语1.标称值nominal value2.示值indication(of a measuring instrument)3.标尺范围scale range4.标称范围nominal range5.标尺长度scale length6.标尺分度scale division7.分度值value of a scale division8.标尺间距scale spacing9.线性标尺linear scale10.非线性标尺non-linear scale11.标尺标数scale numbering12.测量仪器的零位zero of a measuring instrument13.量程span14.测量范围measuring range15.额定工作条件vated operating conditions16.极限条件reference condition17.标准条件reference condition18.仪器常数instrument constant19.响应特性response characteristic20.灵敏度senstivity21.鉴别力discrimination22.分辨力resolution（of an indicating device）23.死区dead band24.准确度accuracy of a measuring instruments25.准确度等级accuracy class26.重复性repeatability of a measuring instrument27.示值变动性varation of indication28.稳定度stability29.可靠性reliability30.回程hysteresis31.漂移drift32.响应时间response time33.测量力（简称“测力”）measuring force几何量测量器具术语1.几何量具测量器具dimensional measuring instruments2.长度测量器具length measuring instruments3.角度测量器具angle measuring instruments4.坐标测量机coordinate measuring machine5.形状和位置误差测量器具form and position error measuring instruments6.表面质量测量器具surface quality measuring instruments7.齿轮测量器具gear measuring instruments8.实物量具（简称“量具”）material measure9.测量仪器（简称“量仪”）measuring instruments10.测量链measuring chain11.测量装置measuring system12.指示式测量仪器indicating(measuring )instrument 13.记录式测量仪器recording（measuring）instrument14.累计式测量仪器totalizing(measuring)instrument15.积分式测量仪器integrating(measuring)instrument16.模拟式测量仪器analogue(measuring)instrument17.数字式测量仪器digital(measuring)instrument18.测量变换器measuring transducer19.传感器sensor20.指示装置indicating device21.记录装置recording device22.记录载体recording medium23.标尺标记scale mark24.指示器index25.标尺scale26.度盘dail一般术语：1.几何量 geometrical product2.量值value(of a quantity)3.真值true value(of a quantity)4.约定真值conventional true value(of a quantity)5.单位unit(of measurement)6.测量measurement7.测试measurement and test8.检验inspecte9.静态测量static measurement10.动态测量dynamic measurement11.测量原理principle of measurement12.测量方法method of measurement13.测量程序measurement procedure14.被测量measurand15.影响量influence quantity16.变换值transformed value(of a measurand)17.测量信号measurement signal18.直接测量法direct method of measurement19.间接测量法indirect method of measurement20.定义测量法definitive method of measurement21.直接比较测量法direct-comparison method of measurement22.替代测量法substitution method of measurement23.微差测量法differential method of measurement24.零位测量法nulll method of measurement25.测量结果result of a measurement26.测得值measured value27.实际值actual value28.未修正结果uncorrected result （of a measurement）29.已修正结果corrected result(of a measurement)30.测量的准确度accuracy of measurement31.测量的重复性repeatability of measurement32.测量复现性reproducibility of measurements33.实验标准偏差experimental standard deviation34.测量不确定度uncertainty of measurement35.测量绝对误差 absolute error of measurement36.相对误差 relative error37.随机误差random error38.系统误差 systematic error39.修正值correction40.修正系数correction factor41.人员误差personal error42.环境误差environmental error43.方法误差error of method44.调整误差adjustment error45.读数误差reading error46.视差parallax error47.估读误差 interpolation error48.粗大误差parasitic error49.检定verification50.校准calibration51.调准gauging52.调整adjustment1.刀口型直尺:knife straigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪 imaging level meter7铸铁平板 cast iron surface plate8.岩石平板 granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪 roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens cast surface 14.表面粗糙度比较样块磨、车、铣、插及刨加工表面Roughness comparisonspecimens-ground, turned, bored,milled,shape and planed 15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machining surfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓 traced profile20.基准轮廓 reference profile21.总轮廓 total profile22.原始轮廓 primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storing stylus instrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profile filtering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument41.静测力的变化change of static measuring force42.静态测力 static measuring force43.动态测量力 dynamic measuring force44.滞后hysteresis45.测头的测量范围transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力 instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输vertical profile component transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blasted surfaces54产品结构几何量计术规范（GPS）geometrical product specifications(GPS) 55表面结构 surface texture56接触式仪器的标称特性 nominal characteristics of contact instruments57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差 maximum permissible error59圆柱直齿渐开线花键量规 gauges for straight cylindrical involute splines60齿厚游标卡尺 Gear tooth vernier calipers61齿轮渐开线样板the involute master of gear 62齿轮螺旋线样板 the helix master of gear63矩形花键量规gauges for straight –sided splines64测量蜗杆 master worm65万能测齿仪universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument70便携式齿轮齿距测量仪manual gear circular pitch measuring instrument 71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuring instrument75梯形螺纹量规gauges for metric trapezoidal screw threads 76工作螺纹量规work gauges for metric trapezoidal screw threads 77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸 Types and dimensions of metric trapezoidal screw threads79.普通螺纹量规型式与尺寸 Types and dimensions of gauges purpose screw threads80.非螺纹密封的管螺纹量规Gauges for pipe threads prcessure-tight joints are not made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差 maximum permissible error83.间隙螺纹量规 Clearance screw gauge84.量针Bar gauge85.螺纹样板 Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made on the threads87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument 89.光栅线位移测量系统Grating linear displacement measuring system 90.光栅角位移测量系统Grating angular displacement measuring system 91.磁栅线位移测量系统Magnet-grid linear displacement measuring system 92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator1.刀口型直尺:knife straigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪imaging level meter7铸铁平板cast iron surface plate8.岩石平板granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens cast surface14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparison specimens-ground,turned,bored,milled,shape and planed15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machining surfaces16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓traced profile20.基准轮廓reference profile21.总轮廓total profile22.原始轮廓primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storing stylus instrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器) probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profile filtering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument 41.静测力的变化change of static measuring force42.静态测力static measuring force43.动态测量力dynamic measuring force44.滞后hysteresis45.测头的测量范围transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输vertical profile component transmission153表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blasted surfaces54产品结构几何量计术规范(GPS)geometrical product specifications(GPS)55表面结构surface texture56接触式仪器的标称特性nominal characteristics of contact instruments57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差maximum permissible error59圆柱直齿渐开线花键量规gauges for straight cylindrical involute splines60齿厚游标卡尺Gear tooth vernier calipers61齿轮渐开线样板the involute master of gear 62齿轮螺旋线样板the helix master of gear63矩形花键量规gauges for straight–sided splines64测量蜗杆master worm65万能测齿仪universal gear measuring instrument 66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictchmeasuring instrument68万能齿轮测量机Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument70便携式齿轮齿距测量仪manual gear circular pitch measuring instrument 71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuring instrument 75梯形螺纹量规gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensions of metric trapezoidal screw threads79.普通螺纹量规型式与尺寸Types and dimensions of gauges purpose screw threads80.非螺纹密封的管螺纹量规Gauges for pipe threads prcessure-tight joints are not made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差maximum permissible error83.间隙螺纹量规Clearance screw gauge84.量针Bar gauge85.螺纹样板Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made on the threads87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument 89.光栅线位移测量系统Grating linear displacement measuring system 90.光栅角位移测量系统Grating angular displacement measuring system 91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator。
量具中英文对照
量具Measuring Tools 计量Gauging卡尺――Caliper 0。
02游标卡尺－――Vernier Caliper数显卡尺――Digital Caliper带表卡尺――Digital Slide CaliperCA=Calipers卡尺深度尺――depth gauge 0。
02数显深度尺――Digital depth gauge 外径深度尺――depth micrometerDI=Depth Indicator深度测试仪千分尺micrometer 0.01外径千分尺――external micrometer, 外径千分尺outside micrometer内径千分尺――Internal micrometer内径千分尺micrometer inside caliper；inside micrometer 深度千分尺micrometer depth gauge；depth micrometer卡钳式内径千分尺－Internal quick caliper dial gauge外径千分尺标准棒――micrometer standard外径千分尺架子――micrometer stand带表外径千分尺――Indicator dial micrometer MI=Micrometer千分尺千分表-Dial indicator数显千分表—Digital indicator千分表外径规―――Dial indicator snap gauges平面规surface gauge磁性吸座－－Magnetic stand孔的轮廓量规－Bore profile gauge KT点接触杠杆千分表—-—Lever dial indicator point contact length可调的磁力架-—--Magnetic stand with fine adjustment高度尺height gauge 0。
02游标高度尺—-—Vernier height gauge数显游标高度尺Digital height gaugeMH=Height tester高度测试仪尺规\刀规－Straight edge板规plate gauge中心规centre gauge锥度规taper gauge比例规proportional dividers标准规standard gauge齿轮规gear tooth gauge分线规divider；dividers工作量规working gauge厚薄规feeler(gauge)角规angle gauge块规gauge(block)量规gauge螺距规screw pitch gauge螺纹千分尺screw micrometer内卡钳inside caliper外卡钳outside caliper圆规compasses椭圆规ellipsograph隙规gap(/clearance）gauge线规wire gauge斜角规bevel square折尺folding pocket measure（/ruler）曲尺carpenter’s square钢尺――steel rule刻度尺graduation ruler丁字尺T—square三角尺set square直尺straight edge皮尺tape(/measure）卷尺Locking tape measure金属卷尺metallic tape角尺――angle square组合角尺combination set花岗岩平台（精度1极）Granite table, accuracy 1装有T型槽的平台-Tenon and T-slot incl。
常见量具中英文对照翻译
常见量具中英文对照翻译 数据处理装置 SPC 游标卡尺 Vernier caliper 深度卡尺 Depth gபைடு நூலகம்ge 高度尺 Height gage 外径千分尺 Micrometer 内径千分尺 Inside micrometer 微分头 Micrmeter head 百分表及内径量表 indicator 杠杆百分表 test indicator 线性测微计 gage head 量块 gauge block 量块附件 reference gage 大理石平板 surface plate 万能角度尺及其它 miscellaneous 光栅尺 linear scale 投影机 profile projector 显微镜 microscope 轮廓测定机 contracer 表面粗糙仪 surftest 组合测量系统 formtracer
真圆度仪 roundtest 硬度计 hardness testr 三坐标 CMM 简易三坐标 flexible measuring gage 2D 视像测量系统 vision measuring sysem 细微形状测量系统 detailed shape measuring system 激光扫描测量仪 laser scan micrometer 特种卡尺 DIY tools
计量器具中英文对照
1. 量块gaugeblock2. 光滑极限量规plainlimit gauge3. 塞规pluggauge4. 环规ringgauge卡规snap gauge5. 塞尺feelergauge6. 钢直尺steelgauge7. 精密玻璃线纹尺precision glass linear scale8. 精密金属线纹尺precision metal linear scale9. 半径样板radiustemplate卡尺类1. 游标卡尺verniercaliper2. 带表卡尺dialcaliper3. 电子数显卡尺calliperwith electronic digital display4. 深度标游卡尺depthvernier caliper5. 电子数显深度卡尺depthcaliper with electronic digital display6. 带表高度卡尺dialheight calliper7. 高度游标卡尺heightvernier caliper8. 电子数显高度卡尺heightcaliper with electronic digital9. 焊接检验尺calliperfor welding inspection千分尺类1. 测微头micrometerhead2. 外径千分尺externalmicrometer3. 杠杆千分尺micrometer with dial comparator4. 带计数器千分尺micrometer with counter5. 电子数显外径千分尺micrometer with electronic digital display6. 小测头千分尺smallanvil micrometer7. 尖头千分尺pointmicrometer8. 板厚千分尺sheetmetal micrometer9. 壁厚千分尺tubemicrometer10. 叶片千分尺blademicrometer11. 奇数沟千分尺oddfluted micrometer12. 深度千分尺depthmicrometer13. 内径千分尺internalmicrometer14. 单杆式内径千分尺single-body internal micrometer15. 表式内径千分尺dailinternal micrometer16. 三爪式内径千分尺threepoint internal micrometer17. 电子数显三爪式内径千分尺three point internal micrometer18. 内测千分尺insidemicrometer指示表类1. 指示表dialindicator2.深度只是表depthdialindicator3. 杠杆指示表dialtestindicator4. 内径指示表boredialindicator5. 涨弹簧式指示表expanding head bore dial indicator6. 钢球式内径指示表balltype bore dial indicator7. 电子数显指示表dialindicator with electronic digital display8. 杠杆卡规indicatingsnap gauge9. 带表卡规dialsnapgauge10. 带表外卡规outsidedial snap gauge11. 带表内卡规insidedial snap gauge12. 测厚规thicknessgauge13. 扭簧比较仪microcator14. 杠杆齿轮比较仪mechanical dial comparator15. 电子量规electronicgauge16. 电感式传感器inductance type transducer17. 指示装置indicatingdevice18. 电感测微仪inductance micrometer19. 峰值电感测微仪peakinductance micrometer20. 电感内径比较仪inductance bore comparator21. 瞄准传感器aimingtransducer角度测量器具1. 角度块angleblockgauge2. 正多面棱体regularpolygon mirror3. 刀具角度样板cutterangular template4.直角尺square5. 平行直角尺parallelsquare6. 宽座直角尺wide-stand square7. 刀口形直角尺edgesquare8. 矩形直角尺squaresquare9. 三角形直角尺threeangle square10. 圆柱直角尺cylindersquare11. 方形角尺squareguage12. 万能角度尺universalbevel protractor13. 游标式万能角度尺vernier universal bevel protractor14. 表式万能角度尺dialuniversal bevel protractor15. 光学分度头opticaldividing head16. 目镜式光学分度头optical dividing head with microscope reading17. 投影式光学分度尺optical dividing head with projection reading18. 光电分度头optical-electronic dividing head19. 多齿分度台multi-tooth division table20. 分度转台divisionrotary table21. 正炫规sinebar22. 普通正炫规generalsine bar23. 铰链式正炫规hingetype sine bar24. 双向正炫规dual-directional sine bar25. 圆锥量规conegauge26. 圆锥塞规plugconegauge27. 圆锥环规ringconegauge28. 直角尺测量仪squaremeasuring instrument计量器具中英文对照汇总表-形位误差测量器具1. 平晶opticalflat2. 单面平晶opticalflat3. 双面平晶paralleloptical flat4. 刀口形直尺knifestraight edge5. 刀口尺knifestraight edge6. 三棱尺threeedgesstraight edge7. 四棱尺fouredgesstraight edge8. 平尺straightedge9. 矩形平尺squarestraight edge10. 工字形平尺i-beamstraight edge11. 角形平尺anglestraight edge12. 桥形平尺bridgetypestraight edge13. 平板surfaceplate14. 铸铁平板castironsurface plate15. 岩石平板granitesurface plate16. 方箱squarebox17. 水准器式水平仪levelmeter18. 条式水平仪barlevelmeter19. 框式水平仪framelevel meter20. 合像水平仪imaginglevel meter21. 光学倾斜仪opticalinclinometer22. 电子水平仪electronic level meter23. 指针式电子水平仪electronic level meter with indicator24.数显式电子水平仪electronic level meter with digital display25. 平直度测量仪straightness measuring instrument26. 光学式平直度测量仪optical straightness measuring instrument27. 光电式平直度测量仪photoelectrical straightnessmeasuringinstrument28. 圆度测量仪roundnessmeasuring instrument29. 转轴式圆度测量仪spindle-rotating type roundnessmeasuringinstrument30. 转台式圆度测量仪table-rotating type roundnessmeasuringinstrument计量器具中英文对照汇总表1.刀口型直尺:knifestraigjht edge2.刀口尺: knife straigjht edge3.三棱尺three edges straigjht edge4.四棱尺four edges straigjht edge5.条式和框式水平仪bar form and square levels6.合像水平仪imaging level meter7铸铁平板cast iron surface plate8.岩石平板granite surface plate9.铸铁平尺cast iron straigjht edge10.钢平尺和岩石平尺steel and granite straigjht edge11.圆度仪roundness measuring instrument12.电子水平仪electronic level meter13.表面粗糙度比较样块铸造表面roughness comparison specimens castsurf ace14.表面粗糙度比较样块磨、车、铣、插及刨加工表面roughness comparison specimens-ground,turned,bored,milled,shapeandpl aned15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion machiningsurfaces 16.表面粗糙度比较样块抛光加工表面roughness comparison specimens pollshed surfaces17.接触式仪器的标称特性18.轮廓profiles19.轨迹轮廓traced profile20.基准轮廓reference profile21.总轮廓total profile22.原始轮廓primary profile23.残余轮廓residual profile24.触针式仪器stylus instrument25.感应位移数字存储触针式量仪displacement sensitive,digitally storin gstylusinstrument26.触针式仪器的部件stylus instrument components27.测量环measurement loop28.导向基准renfence guide29.驱动器drive unit30.测头(传感器)probe(pick-up)31.拾取单元tracing element32.针尖stylus tip33.转换器transducer34.放大器amplifier35.模/数转换器analog-to-digital converter36.数据输入data input37.数据输出data output38.轮廓滤波和评定profile filtering and evaluation39.轮廓记录器profile recorder40.仪器的计量特性metrological characteristics of the instrument41.静测力的变化change of static measuring force42.静态测力static measuring force43.动态测量力dynamic measuring force44.滞后hysteresis45.测头的测量范围transmission function for the sine waves46.仪器的测量范围measuring range of the instrument47.模数转换器的量化步距quantization step of the ADC48.仪器分辨力instrument resolution49.量程分辨力比range-to-resolution ratio50.测头线性偏差probe linearity deviation51.短波传输界限short-wave transmission limitation52.轮廓垂直成分传输vertical profile component transmission53表面粗糙度比较样块抛丸、喷砂加工表面roughness comparison specimens shot blasted and blastedsurfaces54产品结构几何量计术规范（GPS）geometricalproduct specifications(GPS) 55表面结构surface texture56接触式仪器的标称特性nominal characteristics of contact instruments57公法线千分尺micrometer for mearsuring root tangent lenghths of gear teeth58最大允许误差maximum permissible error59圆柱直齿渐开线花键量规gauges for straight cylindricalinvolute splines60齿厚游标卡尺Gear tooth verniercalipers61齿轮渐开线样板the involute master of gear62齿轮螺旋线样板the helix master of gear63矩形花键量规gauges for straight –sided splines64测量蜗杆master worm65万能测齿仪universal gear measuring instrument66万能渐开线检查仪universal involute measuring instrument67齿轮齿距测量仪gear circular pictch measuring instrument68万能齿轮测量机Universal gear measuring machine69齿轮螺旋线测量仪gear helix measuring instrument70便携式齿轮齿距测量仪manual gear circular pitch measuring instrument 71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integratederrormeasuring instrument75梯形螺纹量规gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensions of metric trapezoidalscrewthreads79.普通螺纹量规型式与尺寸Types and dimensions of gauges purposescrewthreads80.非螺纹密封的管螺纹量规Gauges for pipe threadsprcessure-tight joints arenot made on the threads81.螺纹千分尺Screw thread micrometer82.最大允许误差maximum permissible error83.间隙螺纹量规Clearance screw gauge84.量针Bar gauge85.螺纹样板Screw thread template86.用螺纹密封的管螺纹量规Gauges for pipe threads where pressure-tight joints are made onthethreads 87.刀具预调测量仪精度Accuracy of the presetting instrument88.薄膜式气动量仪Membrane type pneumatic measuring instrument89.光栅线位移测量系统Grating linear displacement measuring system90.光栅角位移测量系统Grating angular displacement measuring system91.磁栅线位移测量系统Magnet-grid linear displacement measuring system92.量块附件Accessories for gauge blocks93.V形架Vee blocks94.比较仪座Comparator stand95.磁性表座Magnetic stand96.万能表座Universal stand for dial indicator计量器具中英文对照汇总表一般术语：1. 几何测量geometrical product2. 量值value(ofaquantity)3. 真值truevalue(ofa quantity)4. 约定真值conventional true value(of aquantity)5. 单位unit(ofmeasurement)6. 测量measurement7. 测试measurementand test8. 检验inspecte9. 静态测量staticmeasurement10. 动态测量dynamicmeasurement11. 测量原理principleof measurement12.测量方法methodofmeasurement13. 测量程序measurement procedure14. 被测量measurand15. 影响量influencequantity16. 变换值transformedvalue(of a measurand)17. 测量信号measurement signal18. 直接测量法directmethod of measurement19. 间接测量法indirectmethod of measurement20. 定义测量法definitive method of measurement21. 直接比较测量法direct-comparison method of measurement22. 替代测量法substitution method of measurement23. 微差测量法differential method of measurement24. 零位测量法nulllmethod of measurement25. 测量结果result ofameasurement26. 测得值measuredvalue27. 实际值actualvalue28. 未修正结果uncorrected result（ofameasurement）29. 已修正结果correctedresult(of a measurement)30. 测量的准确度accuracyof measurement31. 测量的重复性repeatability of measurement32. 测量复现性reproducibility of measurements33. 实验标准偏差experimental standard deviation34. 测量不确定度uncertainty of measurement35. 测量绝对误差absoluteerror of measurement36. 相对误差relativeerror37. 随机误差randomerror38.系统误差systematicerror39. 修正值correction40. 修正系数correctionfactor41. 人员误差personalerror42. 环境误差environmental error43. 方法误差errorofmethod44. 调整误差adjustmenterror45. 读数误差readingerror46. 视差parallaxerror47. 估读误差interpolation error48. 粗大误差parasiticerror49. 检定verification50. 校准calibration51. 调准gauging52. 调整adjustment计量器具中英文对照汇总表-几何量测量器具术语1. 几何量具测量器具dimensional measuring instruments2. 长度测量器具lengthmeasuring instruments3. 角度测量器具anglemeasuring instruments4. 坐标测量机coordinate measuring machine5. 形状和位置误差测量器具form and position error measuring instruments6. 表面质量测量器具surface quality measuring instruments7. 齿轮测量器具gearmeasuring instruments 8.实物量具（简称“量具”）materialmeasure9. 测量仪器（简称“量仪”）measuringinstruments10. 测量链measuringchain11. 测量装置measuringsystem12. 指示式测量仪器indicating(measuring )instrument13. 记录式测量仪器recording（measuring）instrument14. 累计式测量仪器totalizing(measuring)instrument15. 积分式测量仪器integrating(measuring)instrument16. 模拟式测量仪器analogue(measuring)instrument17. 数字式测量仪器digital(measuring)instrument18. 测量变换器measuringtransducer19. 传感器sensor20. 指示装置indicatingdevice21. 记录装置recordingdevice22. 记录载体recordingmedium23. 标尺标记scalemark24. 指示器index25. 标尺scale26. 度盘dail计量器具中英文对照汇总表-测量器具术语1. 标称值nominalvalue2. 示值indication(of a measuring instrument)4.5. 标尺长度scalelength6. 标尺分度scaledivision7. 分度值value ofascale division8. 标尺间距scalespacing9. 线性标尺linearscale10. 非线性标尺non-linear scale11. 标尺标数scalenumbering12. 测量仪器的零位zeroofa measuring instrument13. 量程span14. 测量范围measuringrange15. 额定工作条件vatedoperating conditions16. 极限条件referencecondition17. 标准条件referencecondition18. 仪器常数instrumentconstant19. 响应特性responsecharacteristic20. 灵敏度senstivity21. 鉴别力discrimination22. 分辨力resolution（ofanindicating device）23. 死区deadband24. 准确度accuracyofa measuring instruments25. 准确度等级accuracyclass26. 重复性repeatability of a measuring instrument27. 示值变动性varationof indication28. 稳定度stability29. 可靠性reliability30.回程hysteresis31. 漂移drift32. 响应时间responsetime33. 测量力（简称“测力”）measuringforce计量器具中英文对照汇总表-测量器具术语1. 实物量具示值误差errorof indication of a material measure2. 测量仪器示值误差errorof indication of a measuring instrument3. 重复性误差repeatability error of a measuring instrument4. 回程误差hysteresiserror5. 测量力变化variationof measuring force6. 测量力落差hysteresis of measuring force7. 偏移误差biaserror(of a measuring instrument)8. 允许误差maximumpermissible errors(of measuringinstruments)9. 跟踪误差trackingerror (of a measuring instrument)10. 响应率误差response-law error (of a measuring instrument)11. 量化误差quantization error (of a measuring instrument)12. 基值误差datumerror(of a measuring instrument)13. 零值误差zeroerror(of a measuring instrument)14. 影响误差influenceerror15. 引用误差fiducialerror16. 位置误差positionerror17. 线性误差linearerror18. 响应特性曲线responsecharacteristic curve19. 误差曲线errorcurve20.校准曲线calibration curve21. 修正曲线correctioncurve计量器具中英文对照汇总表-表面质量测量器具表面粗糙度比较样块surface roughness comparison specimen铸造表面粗糙度比较样块surface roughness comparison specimen forcastsurface磨、车、镗、铣、插及刨加工表面粗糙度比较样块surface roughness comparison specimenforground,turned,bored,milled,shaped andplanedsurface电火花加工表面粗糙度比较样块surface roughness comparison specimenforspark-erosion machined surface抛（喷）丸、喷砂加工表面粗糙度比较样块surface roughness comparison specimen forshotblasted and grit blasted surface抛光加工表面粗糙度测量仪portable surface roughness comparison specimenforpolished surface便携式表面粗糙度测量仪portable surface roughessmeasuringinstrument驱动箱drivingbox台式表面粗糙度测量仪bench type surface roughnessmeasuringinstrument （素材和资料部分来自网络，供参考。
测量工具中英文对照表
18.轮廓profiles
19.轨迹轮廓 traced profile
20.基准轮廓 reference profile
21.总轮廓 total profile
22.原始轮廓 primary profile
23.残余轮廓residual profile
24.触针式仪器stylus instrument
深度千分尺(Depth Micrometer)
销(针)规(Pin Gauge)
投影仪(Projector )
数字高度测量仪(Digital Height Gauge)
表面处理测试仪(Surface Finish Tester)
内/外径千分尺(Inside/outer Micrometer)
81.螺纹千分尺
Screw thread micrometer
82.最大允许误差 maximum permissible error
83.间隙螺纹量规 Clearance screw gauge
84.量针
Bar gauge
85.螺纹样板 Screw thread template
86.用螺纹密封的管螺纹量规
46.仪器的测量范围measuring range of the instrument
47.模数转换器的量化步距quantization step of the ADC
48.仪器分辨力 instrument resolution
49.量程分辨力比range-to-resolution ratio
高度仪(Altitude gauge)
塞尺/间隙规(Clearance gauge)
量具中英文对照
量具中英文对照量具中英文对照卡规snap gauge5.塞尺feeler gauge 卡尺类6.钢直尺 steel gauge7.1.游标卡尺vernier caliper 精密玻璃线纹尺precision glass linear scale8.精密金属线纹尺2.带表卡尺dial caliper precision metal linear scale9. 半径样板radius template 3.电子数显卡尺测量器具术语calliper with electronic digital display深度标游卡尺depth vernier caliper 4.1.实物量具示值误差error of indication of a 5.电子数显深度卡尺material measuredepth caliper with electronic digital display2.测量仪器示值dial height calliper 误差error of indication ofa 6.带表高度卡尺measuring instrumentheight vernier caliper7.高度游标卡尺3.caliper with 重复性误差repeatability error ofa measuring height 高8.电子数显度卡尺instrumentelectronic digital display4.回程误差calliper for welding inspection hysteresis error9.焊接检验尺5.千分尺类测量力变化variation of measuring force6. 测量力落差hysteresis of measuring force7.偏移误差bias error micrometer head1.测微头(of a measuring instrument)8.允许外径千分尺2.external micrometer误差maximum permissible errors(ofmeasuring instruments)3.杠杆千分尺micrometer with dial comparator9.跟踪误差tracking error 带计数器千分尺4.micrometer with counter (of a measuring instrument)电子数显外径千分尺5.10.micrometer with electronic digital display 响应率误差response-law error (of a measuring instrument)小测头千分尺small anvil micrometer 6.11.7.量化误差quantization error (of a measuring 尖头千分尺point micrometer instrument)板厚千分尺sheet metal micrometer 8.12.基值误差datum error 壁厚千分尺9.tube micrometer (of a measuringinstrument)blade micrometer10.叶片千分尺13.零值误差zero 奇数沟千分尺11.odd fluted micrometer error (of a measuringinstrument)12.深度千分尺depth micrometer14.影响误差internal micrometer influence error 内径千分尺13.15.引用误差 14.单杆式内径千分尺fiducial error16.single-body internal micrometer位置误差position error17.线性误差 dail internal micrometer 15.表式内径千分尺linear error18. 响应特性曲线response characteristic curve 三爪式内径千分尺16.19.误差曲线error curvethree point internal micrometer20.电子数显三爪式内径千分尺17. 校准曲线calibration curve21.修正曲线three point internal micrometer correction curve测量器具术语inside micrometer 内测千分尺18.1.标称值nominal value长度测量器具 2. 量具类示值indication(of a measuring instrument)3.gauge block标尺范围scale range 量块1.4.plain limit gauge 光滑极限量规2.标称范围nominal range 5.标尺长度scale length plug gauge 塞规3.scale division标尺分度6.ring gauge环规4.7.分度值value of a scale division 13.记录式测量仪器recording（scale spacing measuring）instrument 8.标尺间距14.9.线性标尺linear scale 累计式测量仪器totalizing(measuring)instrument 非线性标尺non-linear scale10.15.scale numbering11.标尺标数积分式测量仪器integrating(measuring)instrumentof a measuring instrument 12.测量仪器的零位zero16.模拟式测量仪器13.量程spananalogue(measuring)instrument17.数字式测量仪器14.测量范围measuring rangedigital(measuring)instrument18.测量变换器measuring transducer 15.额定工作条件vated operating conditions19.传感器sensor极限条件16.reference condition20.指示装置reference condition indicating device 17.标准条件21.18.仪器常数instrument constant 记录装置recording device22.记录载体response characteristic recording medium 19.响应特性23.20.灵敏度senstivity 标尺标记scale mark24.鉴别力指示器discriminationindex 21.25.22.分辨力resolution标尺scale （of an indicating device）26.度盘dail 23.死区dead band一般术语：准确度24.accuracy of a measuring instruments1.几何量 geometrical product accuracy class 25.准确度等级2.量值value(of a quantity) 26.重复性3.真值repeatability of a measuring instrument true value(ofa quantity)4.约定真值示值变动性varation of indication 27.conventional true value(of a quantity) 28.稳定度stability5.单位可靠性29.reliability unit(of measurement)6.hysteresis 30.回程测量measurement7.测试measurement and test 漂移31.drift8.response time 响应时间检验inspecte32.9.33.静态测量measuring force 测量力（简称“测力”）static measurement10. 几何量测量器具术语动态测量dynamic measurement11. 测量原理principle of measurement12.测量方法 1.几何量具测量器具method of measurement13.测量程序dimensional measuring instrumentsmeasurement procedure14.被测量length measuring instruments 2.长度测量器具measurand15.影响量influence quantity角度测量器具3.angle measuring instruments16.变换值transformed value(of a measurand) coordinate measuring machine4.坐标测量机17.测量信号error and 形状和位置误差测量器具5.form position measurement signal18.直接测量法direct method of measurement measuringinstruments19.间接测量法indirect method of measurement 6.表面质量测量器具20.surface quality measuring instruments 定义测量法definitive method of measurement21.gear measuring instruments 齿轮测量器具直接比较测量法7.direct-comparison method of measurement）material measure 实物量具（简称“量具”8.22.替代测量法substitution measuring instruments 测量仪器（简称“量仪”9.）method of measurement23.微差测量法differential measuring chain 测量链10.method of measurement24.零位测量法nulll method of measurement measuring system 测量装置11.25.测量结果指示式测量仪器12.result of a measurementmeasured value测得值26.indicating(measuring )instrument27.实际值actual value 15.表面粗糙度比较样块电火花加工表面roughness comparison specimens spark-erostion 28.未修正结果machining surfaces （of a measurement）uncorrected result16.表面粗糙度比较样块抛光加工表面measurement) 29.已修正结果corrected result(of a roughness 30.测量的准确度accuracy of measurementcomparison specimens pollshed surfaces17.接触式仪器的标称特性31.测量的重复性repeatability of measurement18.轮廓reproducibility of measurements profiles32.测量复现性19.实验标准偏差轨迹轮廓experimental standard deviation traced profile33.20.34.测量不确定度uncertainty of measurement 基准轮廓reference profile21.总轮廓35.测量绝对误差absolute error of measurement total profile22.原始轮廓相对误差36. relative error primary profile23.残余轮廓37.随机误差random errorresidual profile24.触针式仪器stylus instrument38.系统误差 systematic error25.感应位移数39.修正值correction字存储触针式量仪displacementsensitive,digitally storing stylus instrument 修正系数40.correction factor26.触针式仪器的部件stylus personal error41.人员误差instrument components27.environmental error 测量环measurement loop 环境误差42.28.导向基准renfence guide 43.方法误差error of method29.驱动器drive unit调整误差44.adjustment error30.测头(传感器)probe(pick-up) reading error 45.读数误差31.拾取单元tracing element 46.视差parallax error32.针尖 interpolation error 47.估读误差stylus tip33.parasitic error 转换器transducer 粗大误差48.34.49.检定放大器amplifier verification35.模校准50.calibration /数转换器analog-to-digital converter36.数据输入51.调准gauging data input37.adjustment数据输出data output 调整52.38.:knife straigjht edge 刀口型直尺轮廓滤波和评定1.profile filtering and evaluation2.刀口尺: knife straigjht edge39.轮廓记录器profile recorder three edges straigjht edge 3.三棱尺40.four edges straigjht edge 仪器的计量特性四棱尺4.metrological characteristics of the instrument 条式和框式水平仪5.41.静测力的变化change bar form and square levelsof static measuring force42.静态测力imaging level meter 6.合像水平仪static measuring force43.动态测量力 dynamic measuring force 铸铁平板7 cast iron surface plate44.滞后 granite surface plate 岩石平板8.hysteresis45.测头的测量范围cast iron straigjht edge 铸铁平尺9.transmission function for the sine waves 10.钢平尺和岩石平尺46.steel and granite straigjht edge仪器的测量范围measuring range of the instrument 圆度仪11. roundness measuring instrument47.模数转换器的量化步距电子水平仪12.electronic level meterquantization step of the ADC表面粗糙度比较样块铸造表面13.48.仪器分辨力instrument resolutionroughness comparison specimens cast surface49.量程分辨力比表面粗糙度比较样块磨、车、铣、插及刨加工表面14.range-to-resolution ratioRoughness comparisonspecimens-ground, turned, 50.测头线性偏差probe linearity deviation 短波传输界限51.,shape and planed bored,milledshort-wave transmission limitation 76工作螺纹量规work gauges for metric trapezoidal screw threads 52.轮廓垂直成分传输77校对螺纹量规vertical profile component transmissioncheck gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸表面粗糙度比较样块抛丸、喷砂加工表面53 Types anddimensionsof metric trapezoidal screw threadsroughness comparison specimens shot blasted and79.普通螺纹量规型式与尺寸blasted surfacesTypes and dimensionsof gauges purpose screw threads54产品结构几何量计术规范80.非螺纹密封的管螺纹量GPS（）geometrical product specifications(GPS) 规 Gauges for pipe threads prcessure-tight joints are not made on the 55表面结构 surface texture threads接触式仪器的标称特性 nominal characteristics 5681.of contact instruments螺纹千分尺Screw thread micrometer57公法线千分尺micrometer for mearsuring root82.最大允许误差tangent lenghths of gear teethmaximum permissible error83.间隙螺纹量规 maximum permissible error58最大允许误差 Clearance screw gauge84.量针圆柱直齿渐开线花键量规 gauges for straight Bar gauge5985.cylindrical involute splines螺纹样板 Screw thread template86. Gear tooth vernier calipers 用螺纹密封的管螺纹量规 60齿厚游标卡尺Gauges for pipe threads where pressure-tight 齿轮渐开线样板the involute master of gear 61joints are made on the threads 62齿轮螺旋线样板 the helix master of gear87.刀具预调测量仪 sided straight 规键形63矩花量 gauges for–精度Accuracy of the presetting instrument splines88.64测量蜗杆 master worm 薄膜式气动量仪Membrane type pneumatic measuring instrument 万能测齿仪6589.光栅线位移测量系统universal gear measuring instrument Grating linear displacement measuring system 万能渐开线检查仪6690.光栅角位移测量系统universal involute measuring instrumentGrating angular displacement measuring system 齿轮齿距测量仪6791.磁栅线位移测量系统gear circular pictch measuring instrumentMagnet-grid linear displacement measuring 万能齿轮测量机68 system92.量块附件 Universal gear measuring machineAccessories for gauge blocks 齿轮螺旋线测量仪6993.Vgear helix measuring instrument 形架Vee blocks 便携式齿轮齿距测量仪7094.manual gear circular pitch measuring instrument 比较仪座Comparator stand 71 便携式齿轮基节测量仪95.manual gear base pitch measuring instrument 磁性表座Magnetic stand 立式滚刀测量仪7296.万能表座vertical hob measuring instrument Universal stand for dial indicator 齿轮双面啮合综合测量仪73Gear dual-flank measuring instrument1. 齿轮单面啮合整体误差测量仪74刀口型直尺:knife straigjht edge2.刀口尺Gear single-flank meshing integrated error : knife straigjht edge3.measuring instrument 三棱尺three edges straigjht edge4.75四棱尺four edges straigjht edge梯形螺纹量规bar form and square levels条式和框式水平仪5.gauges for metric trapezoidal screw threads6.合像水平仪imaging level meter 41.静测力的变化change of static measuring force42.7铸铁平板cast iron surface plate 静态测力static measuring force43.动态测量力dynamic measuring force 8.岩石平板granite surface plate44.滞后9.铸铁平尺cast iron straigjht edgehysteresis45.steel and granite straigjht 测头的测量范围transmission function for the 10.钢平尺和岩石平尺sine wavesedge46.仪器的测量范围圆度仪11.roundness measuring instrument measuring range of the instrumentelectronic level meter12.电子水平仪47.模数转换器的量化步距造粗13.表面糙度比较样块铸表面roughness quantization step of theADCcomparison specimens cast surface48.仪器分辨力instrument resolution14.表面粗糙度比较样块磨、车、铣、插及刨加工表面49.量程分辨力比range-to-resolution ratio comparison roughness50.测头线性偏差and probe linearity deviationspecimens-ground,turned,bored,milled,shape51.planed短波传输界限short-wave transmissionlimitation表面粗糙度比较样块电火花加工表面roughness 15.52.spark-erostion machining 轮廓垂直成分传输vertical profile component specimens comparisontransmission1surfaces53表面粗糙度比较样块抛丸、喷砂加工表面16.表面粗糙度比较样块抛光加工表面roughness roughnesscomparison specimens shot comparison specimens pollshed surfaces blasted and blasted surfaces17.接触式仪器的标称特性54轮廓18.profiles产品结构几何量计术规范(GPS)geometricalproduct specifications(GPS) 轨迹轮廓traced profile 19.5520.表面结构surface texture 基准轮廓reference profile56接触式仪器的标称特性nominal characteristics 21.总轮廓total profileof contact instrumentsprimary profile 原始轮廓22.57公法线千分尺micrometer for mearsuring root residualprofile 23.残余轮廓tangent lenghths of gear teethstylus instrument触针式仪器24.58仪最大允许误差displacement maximum permissible error量针储字移应25.感位数存触式59sensitive,digitally storing stylus instrument 圆柱直齿渐开线花键量规gauges for straight cylindrical involute splinescomponents stylus 26.触针式仪器的部件instrument60齿厚游标卡尺测量环27.measurement loop Gear tooth vernier calipers6128.齿轮渐开线样板renfence guide 导向基准the involute master of gear62驱动器29.drive unit齿轮螺旋线样板the helix master of gear63传感器(30.测头矩形花键量规) probe(pick-up)gauges for straight拾取单元31.tracing element –sided splines64测量蜗杆stylus tip 32.针尖master worm65万能测齿仪转换器33.transducer universal gear measuring instrument6634.amplifier放大器万能渐开线检查仪universal involute measuringinstrument35./模数转换器analog-to-digital converter6736.data input 数据输入齿轮齿距测量仪gear circular pictchmeasuring instrument 37.data output 数据输出6838. 轮廓滤波和评定万能齿轮测量机Universal gear measuring machine profile filtering and evaluation69profile recorder轮廓记录器39.齿轮螺旋线测量仪gear helix measuring instrument 仪器的计量特性40.metrological characteristics便携式齿轮齿距测量仪70of the instrumentmanual gear circular pitch measuring instrument71便携式齿轮基节测量仪manual gear base pitch measuring instrument72立式滚刀测量仪vertical hob measuring instrument73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuring instrument 75梯形螺纹量规gauges for metric trapezoidal screw threads76工作螺纹量规work gauges for metric trapezoidal screw threads77校对螺纹量规check gauges for metric trapezoidal screw threads78.梯形螺纹量规型式与尺寸Types and dimensions of metric trapezoidal screw threads。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
量具中英文对照表(机械专业)
游标卡尺－――Vernier Caliper
数显卡尺――Digital Caliper
带表卡尺――Digital Slide Caliper
深度――depth gauge
数显深度尺――Digital depth gauge
卡尺――Caliper
角尺――angle square
钢尺――steel rule
外径千分尺――external micrometer,
平面规surface gauge
外径千分尺――external micrometer
外径千分尺标准棒――micrometer standard
外径千分尺架子――micrometer stand
带表外径千分尺――Indicator dial micrometer
千分表外径规―――Dial indicator snap gauges
外径深度尺――depth micrometer
内径千分尺――Internal micrometer
花岗岩平台（精度1极）Granite table, accuracy 1装有T型槽的平台-Tenon and T-slot incl. installation 千分表-Dial indicator 数显千分表-Digital indicator 磁性吸座－－Magnetic stand
孔的轮廓量规－Bore profile gauge KT
卡钳式内径千分尺－Internal quick caliper dial gauge
点接触杠杆千分表---Lever dial indicator point contact length 可调的磁力架----Magnetic stand with fine adjustment
游标高度尺---Vernier height gauge
游标高度尺Digital height gauge
尺规\刀规－Straight edge
直尺－steel ruler
角尺－Square
卷尺Locking tape measure。