外贸产品不良描述中英文对照
产品不良名称中英文对照
PC膜 不良
少切 Under cut 过切 Over Cut 剥离 Delamination 波纹 Wrinkle 压伤 Breaking 原物料不良 Material NG
刮伤 Scratch 透光 Dead Color, Transparency 黑点 Black Dot 起苍 Silver Streak 剥离 Delamination 冲墨 Wash out IMD冲膜 Wash out 缩水 Shrinkage 变形 Transfingeration / Deform 缺料 Void 折痕 Silver Break 脏污 Dirty / Contamination 偏位 Offset 凹点 Dented / Concave
Dirty / Contamination Scratch Distressed / Breaking Dented / Concave Convex Offset Deform Void Silver Break Split Abrade,grind
透光 Dead Color, Transparency
不良项中英文对照
制程
不良项
刮伤 Scratch 手痕 Finger Print
毛屑 Fiber
印刷点 Printing Dot
透光 Dead Color, Transparency
偏位 Biased, Offset
锯齿 Saw, Zigzag
色差 Discoloration
气泡 Bubble
折痕 Silver Break
模 Sticking 过火 BOuvrenr Size / Dimension out of 尺寸不符 spec. 压伤 Breaking 刮伤 Scratch 透光 Dead Color,Transparency 偏位 Deform 脏污 Dirty/Contamination 残胶 Adhensive Out/Glue Residual 溢胶 Glue Smear/Over Glue
验货缺陷中英文对译明
电机不转
motordead无接地电阻Earthyresistancetestfailed
41
高压击穿
Highvoltagetestfailed高High/电压voltage/测试test/失败failed
42
接触不良
Switchpoorconnecting连接connecting
43
焊线虚焊
linefalseWeld线line/假的false/焊接Weld
44
标签翘起
Cnotstickedwell/labelbadsticked/标签Label粘贴sticked好well
45
开关推钮
Switchbutton
46
印刷脱落
PoorPrinting印刷Printing
47
内锅破裂
Innerpotbroken内部的Inner/锅pot/破裂的broken
48
61
配件遗漏
Accessoryismissed附件Accessory/遗漏omitted/错过missed
62
PTC不工作
PTCfunctiondead
63
后盖装配不良
Rearcoverpoorassembling后方Rear/盖cover/装配assembling/前方front
64
有效长度
Effectivelength有效的Effective/长度length
加热元件发黑
Heatingelementblack力口热Heating/兀件elemen/黑black
28
加热元件发红
Heatingelementred红red
29
加热元件发热不均匀
Heatingelementheatinequable热heat不均匀inequable
验货缺陷中英文对照
验货缺陷中英文对照DanWang 发表于: 2008-6-06 19:03 来源: 外贸验货员网carton marking wrong/箱唛错carton was damaged/箱烂carton wrinkle/箱邹poor printing on carton/箱唛印刷不良carton marking illegible/箱唛不清楚carton too tight/箱太紧bar code wrong/电脑纹错wrong printing on carton/箱印刷错bar code illegible/电脑纹模糊missing date code/漏日期贴纸missing bar code/漏电脑纹missing vendor code/漏厂编号missing product inside carton./漏装产品carton joint opened/箱驳口开裂carton unsealed/外箱无密封glue mark on carton/外箱胶水印gift box unseal/彩盒无密封gift box crushed/彩盒压烂压皱master carton/外箱shipping carton/落货箱inner carton/内箱blister pack/吸塑袋gift box pack/彩盒袋display box pack/开口彩盒solid pack/独立装assortment pack/混合装bulk pack/散包装cable tie/扎线带shrink warp/吸塑包装whole pack/完整包装bilingual pack/两种语言装gift box dirty/soil/彩盒污糟gift box wrinkle/彩盒皱gift box scratched/彩盒刮伤gift box deformed/dent/彩盒变形/凹陷gift box illegible/彩盒字迹模糊gift box wet/彩盒湿gift box poor sealing/彩盒封口不良gift box unsealed/彩盒无封口gift box flap seam opened/彩盒盖破裂tape poor sticking/胶纸粘贴不良gift box color deviation/彩盒颜色偏差poor printing on gift box/彩盒印刷不良gift box abrasion/彩盒擦伤gift box adhesion/彩盒相粘window box film damaged/彩盒胶窗烂window box film stress/彩盒胶窗顶白window box film dent/彩盒胶窗凹陷window box film detach/彩盒胶窗脱落window box film poor sealing/彩盒胶筒粘合不良window box film poor transparency/彩盒胶袋透明度不够foreign brand model/错型号wrong destination label/错目的地贴纸no suffoca tion warring on poly bag/胶袋无警告字语no recycling mark/无环保贴纸missing serial number/漏号码贴纸serial number don’t correspond/号码与彩盒不符missing label/漏贴纸missing manual/漏说明书missing accessories/漏附件gift box slightly damage/彩盒轻微损坏uneven coloring/颜色不平均illegible printing/印刷模糊wrong/missing coloring/错/漏颜色missing printing/漏印刷字句missing caution tags for transit漏搬运小心贴纸blister card was dirty/soil卡片是肮脏的/土壤insert(cardboakd)wrinkle 皱纹blister card damaged卡片损害blister card incorrect 备置卡片不正确的cardboard color deviationcardboard 彩色偏离shrinkage缩水deformed变形flash/gate remnantmatted无光泽flow line/stress mark夹水纹/顶白poor molding喷塑不良contamination mark混色,混料mark 痕迹,污点,标记colourized 混色color deviation 颜色偏差color mismatched 颜色不配合burnt mark 烧焦痕damaged 烂/损坏poor trimming 修整不良dull surface 哑色poor spraying 喷油不良over spraying 飞油paint under coverage油太薄paint chipped off脱油orange peel painting油面呈橙皮壮foreign painting染油poor re-painting touchup补油不良missing spraying漏喷油dirty on paint surface油面有尘点paint bubbles油泡paint color deviation油颜色偏差paint color mismatched喷油颜色不配合paint abrasion fail油漆被擦paint adhesion fail油漆被甩paint dirty油面污糟spraying scratched喷油刮花dull of paint surface喷油哑色paint matted/frayed喷油无光泽/磨损yellowish painting油面发黄paint peel off油面起皮spraying uneven喷油不整齐paint damped油漆不干paint abrasion甩油bubble冒泡,气泡uneven paint coverage 喷油厚薄,不均paint misregistration错色poor coating油漆外层不良。
产品缺陷中英文对照表
入水管漏水
Leaking on input water tube
MA
漏斗不能止水
No drip stop on filter basket
MA
漏斗披峰
Flashing on filter cone
MI
底座与底盖离拉
Gap between base and bottom cover
MI
底座与底盖错位
MI
指示管弹起
Water level tube out the position
MI
保温瓶盖漏装单向阀
Missing valve of carafe cover
MA
保温瓶盖漏装密封圈
Missing seal ring on carafe cover
MA
水箱入水口波珠不动
Quiescent ball of water inlet
Missing marking on carton
MA
漏贴电压贴纸
Missing rating label
MA
电线烫伤表皮
Damaged power inside lid
MA
用错面包桶
Wrong bake pan
MA
纤维线露出窗外
Fiber wire out the shutter on housing
MI
指示管丝印不良
Poor silk-screen on water level tube
MI
漏斗丝印花
Poor silk-screen on basket
MI
指示管漏丝印
Water level tube missing silk-screen
MA
产品缺陷名词中英文对照表
串劃 字劃孌暗 顯示不通過 DB不良 晶片損傷 晶片脫落 晶片偏位 焊盤髒 背光源 電極氧化 電極破損 銀膠裂開
64 Reflector press on the dice 65 Sagging wire 66 Soldering broken 67 Solder risidual caused short circuit 68 Solder risidual on PCB 69 Row-thread broken Scratched on Reflector Seep segment(1/3 Segment) Short circuit Second stitch peeling off Bur
防水油
混機種與等級 節死 開路(斷路) Opening of Row-thread exposed metal wire 排線開口處露金屬線 外形尺寸 數量短少 蝕刻過度 上 弧倒 爛焊 錫渣短路 PCB上有錫渣 排線爛 反射蓋劃傷 字劃滲透(1/3字劃) 短路 第二焊點脫落 批峰
產品缺陷名詞中英文對照表
項目
Update date:Aug,30,2006
1 2 3 4 5 6 7 8 9
英文 Poor adhesive force Aluminium-wire broken Basic(Raw) material failure Poor plating Bur
中文 粘力差(膠紙 鋁線爛 基材不良 電鍍不良 毛刺
Epoxy on surface Epoxy on wall Epoxy overfill Epoxy QTY low /Epoxy underfill 30 Electromigration(Micro 微短路 PCB短路 75 Short circuit on PCB short circuit) 銀膠短路 76 Poor silk screen 絲印不良 31 Epoxy caused short circuit 銀膠浮起 77 Sop sponge wheel adhere Cu-power 吸水海棉轆沾有銅粉 32 Epoxy floating up 33 Foreign material /object /body異物 78 Solder Bridge 連錫 34 Fiberglass uneven 纖維布不均 79 The durability of epoxy is insufficient 銀膠膠力不夠 第一焊點脫落 Uneven brightness 80 亮度不均 35 First stitch peeling off 36 High Vf 正向壓降高 81 Uneven color 顏色不均 37 Highly viscosity/highly chance 太粘/很大可能 82 Highly toxic gase/highly suspect 巨毒氣體/很懷疑 IC管孌形 83 Void 白點 38 IC tube warpage 39 Inner carton&shipping box 內外包裝箱 84 Water cleaning insufficient 水洗不充分 40 INT 不穩定 85 Warp/Transform 孌形 41 IR/Reverse current 反向電流 86 White(Green) masking 白(綠)油 光強 打不上線 42 IV 87 Wire Bonding fails 泄光 88 Wrong bin grade 亮度等級錯 43 Light leakage 背光板不良 89 Wrong dice 用錯晶片 44 Back Light board failure 45 Marking permancy 印章永久性 89 Wrong label 標簽錯 46 Marking out of position 印章位置錯 90 Wrong mark 印章錯 Missing dice 46 91 Wrong pole and bining cop 極性與等級印章錯 漏上晶片 可以表示不良的英文詞有:failure,defect,poor,imperfect,fault,flaw,weak,insufficent,not well,problem,,shortcoming, Failure:含义包括,失败、失效、故障、事故、中断、损坏、折断、衰退、缺少、不足等 prepared by: Patrick Chu Confirmed by: Donald Mok
产品不良 英文作文
产品不良英文作文英文:As a consumer, I have encountered the problem of receiving defective products several times. This is really frustrating because I have already paid for the product and I expect it to be in good condition. In such situations, I usually contact the customer service of the company and explain the problem. Sometimes they offer to send a replacement or refund, but other times they ask me to send the defective product back to them for inspection.One time, I ordered a pair of shoes online and when they arrived, I noticed that there was a tear on the side of one of the shoes. I contacted the customer service and they immediately offered to send a replacement pair. I was satisfied with their response and appreciated their quick action.However, there was another time when I received adefective phone charger. I contacted the customer service and they asked me to send the charger back to them for inspection. After a few days, they informed me that the charger was not covered by the warranty and they could not offer a replacement or refund. I was disappointed withtheir response and felt like I had wasted my time and money.Overall, I think it is important for companies to take responsibility for their defective products and offer a solution to their customers. Good customer service can make a big difference and create loyal customers.中文:作为一名消费者,我曾多次遇到收到不良产品的问题。
常见产品不良英文词汇
Scratch 刮花Peel off 剝落Dent 凹陷Dent 撞凹Flash (塑膠)披鋒insufficient 不足Burr (金屬)披鋒excessive 過度Deformation 變形off indication 指示位置不正確Shrinkage 縮水off center 不正中Mix color 混色sink mark 縮水Poor plating 電鍍不良incomplete moulding/punching productPoor assembly 裝配不良不完整制程品Rust 生銹folding slot location shift 切口不良Tight 緊poor ultrasonic-welding 超聲波焊接不良Loose 松screw thread strip 螺紋不良Damage 損壞missing artwork 漏絲印Concave 凹incomplete screw-threads 絲印不完整Convex 凸pin-mark project 頂針位不平Dirty 髒tilt posted 斜貼Bend 彎曲white mark of mould eject pin impact 頂白Crack 裂water leakage 漏水Mismatch段差wrinkle 皺紋Poor silk-screen絲印不良Dimension out of specification 尺寸不合規格Poor print 絲印不良Poor adhered 貼附不良Missing parts 漏件Wrong parts 錯件Color mismatch 顏色不配(色差)Blister 起泡Gap/interval間隙Shape edge 銳邊Poor surface finishing 表面不良Poor spraying 噴油不良Poor hot-tamping 熔接不良Poor lacquer coating 噴漆不良Copper clip expose 銅片外露Artwork failed on tape-pulling test絲印測試失敗Artwork location shifted絲印位置不正確poor legible marking(Date code)標記不清晰(Date code)Unsmooth-turning 轉動不良Poor hot-welding 熱熔接不良Crease 摺痕ComplaintBasket-other complaint 過濾槽-其它客訴incomplete brew 未完成煮水not brew 不煮水Brews-slowly 煮水-慢Clock-other complaint 時鐘-其它客訴Coffee-not hot enough 咖啡-不夠熱Control panel-other complaint 控制面板-其它客訴Control setting skipping控制裝置失效Decanter-not pouring correctly 玻璃杯-倒水不良Display-hard to read 顯示-難以閱讀Noise 噪音Parts damaged 零件損壞Risk-management 危險操作Timer-malfunction 計時器-無功能Coating peeling 塗層脫落Unit-condensation 產品凝結物Excessive steam/condensation 蒸氣過多/凝結物Unit-Leaks 產品-遣漏Unit-leaks from bottom 產品-從底部洩漏No power 無功率Not hot enough 不夠熱Overflow 溢流Rust/corrosion 生銹/腐蝕Stops during use 使用時中止Warming plate-cracked 保溫片-破裂Warming plate-not heating 保溫片-不供熱Water deposits 水沉澱1.the shower head can’t have rough burrs 蓮蓬頭不可有毛邊the showerhead had rough burrs蓮蓬頭有毛邊2.dual water windows can’t have the fingerprint 視窗內不可有指紋dual water windows had the fingerprint 視窗內有指紋3.the buckling of housing and the base can’t have intervals 本體與底座扣合不可有間隙the buckling of housing and the base had intervals 本體與底座扣合有間隙4. the carafes can’t have be dirty 玻璃杯不可有髒污the carafes had be dirty 玻璃杯有髒污5.between the heat shield and the base can’t have intervals 隔熱墊與底座不可有間隙between the heat shield and the base had intervals 隔熱墊與底座有間隙6.the decorative board can’t be dirty 飾板不可有髒污the decorative board was dirty 飾板有髒污7.the warming plate can’t have gravel sand 保溫片不可有砂粒the warming plate had gravel sand 保溫片有砂粒8.the heat shield can’t have intervals 隔熱墊不可有間隙the heat shield had intervals 隔熱墊有間隙9.the housing can’t have scraped 本體不可有刮花the housing have scraped 本體有刮花10.the front decorative board was dirty 前飾板有髒污11.the carafe lid deformation 杯蓋變形12.the up lid had scraped 上蓋刮花13.the base cover was dirty 底蓋有髒污14.the heat shield had rough burrs 隔熱墊有毛邊15.the heat shield had scraped 隔熱墊刮花16.the right decorative/plaque board had scraped 右飾板刮花Common use English of word日期時間類年Year月Month日Day 上午Morning 下午Afternoon 晚上Night星期一Monday 星期二Tuesday 星期三Wednesday 星期四Thursday 星期五Friday 星期六Saturday 星期日Sunday一月January 二月February 三月March四月April 五月May 六月June 七月July 八月August九月September 十月October 十一月November 十二月December常用零件把手handle 保險絲fuse 蓋cover 電源線power cord 溫控thermostat 電熱管heater 插頭plug水位視窗water level tube 內配線lead wire 氖燈lamp 過濾槽filter basket 漏斗filter cone 保溫片warming plate 電木圈insulation ring 開關switch 底蓋bottom cover 底座base 按鍵button 銘牌Logo 入水蓋inlet cover 玻璃杯decanter/carafe 控制面板control panel 腳粒rubber foot/bet 上本體up house下本體lower house 保溫毯warming blanket 發熱管/發熱線/雲母片heating tube/heating element/sheet mica 噴霧spray mist電源線鉗cord clamp柱boss/post(pillar/column 一般用於建築)恆溫器/恆溫保險絲thermostat/thermo fuse(TCO)膠腳rubber foot電源線長度power cord length電木phenolic骨rid腳leg 托架element bracket圈ring密封圈seal ring防逆閥check valve保險絲thermal cutoff 定時器timer包裝類保證卡guaranty card 警告卡warranty card 規格標rating label 螺絲screw PE袋PE film 說明書instruction book 彩盒gift box/color box 外箱carton 毛重gross weight 淨重net weight 尺寸size正麥front mark 側麥side mark條碼bar code其它見備注see remark 日期碼date code 只PCS 退貨Reject 客戶Customer 數量quantity 不合格failed 合格pass 嚴重major 輕微minor 接受Accept 型號Model NO干燒時間dry time煮水時間brew time 水溫water temperature 噪音noise 溢出overflow 打開或拆開分析teardown analysis 螺絲扭力screw torque 輕微slightly銷售地芬蘭Finland 法國France 德國Germany 印度India 意大利Italy 日本Japan 科威特Kuwait 澳門Macao 蒙古Mongolia 荷蘭Netherlands 尼日利亞Nigeria 挪威Norway 秘魯Peru 菲律賓Philippines 波蘭Poland 葡萄牙Portugal羅馬尼亞Romania 新加坡Singapore南非South Africa 西班牙Spain瑞典Sweden瑞士Switzerland 台灣Taiwan阿根廷Argentina澳大利亞Australia 巴西Brazil 加拿大Canada 智利Chile哥倫比亞Colombia 哥斯達黎加Costa Rico 古巴Cuba 丹麥Denmark 美國American/United States 委內瑞拉Venezuela拉丁美洲Latin America 邁阿密Miami。
产品不良名称中英文对照
缺料 折痕 拉裂 擦伤 透光 少切 过切 剥离 波纹 压伤
组装
残胶 溢胶
PC膜 不良
原物料不良 Material NG
刮伤 透光 黑点 起苍 剥离 冲墨 缩水 变形 缺料 折痕 脏污 偏位 凹点 流痕 雾面 凸点
Scratch Dead Color, Transparency Black Dot Silver Streak Delamination Wash out Shrinkage Transfingeration / Deform Void Silver Break Dirty / Contamination Offset Dented / Concave Flow Mark Cloudy / Haze Convex Flash / Fiber Parting Line Flash / Flash Finger Print Others
不良项中英文对照
制程
刮伤 手痕 毛屑 印刷点 透光 偏位 锯齿 色差 气泡 折痕 收缩 溢墨 缺印 断线 鬼影 不全 污秽 字体 边缘裂 银点 缺墨 脏污 阴影 虚线 针孔 视窗偏位 视窗变形 凸点
不良项
Scratch Finger Print Fiber Printing Dot Dead Color, Transparency Biased, Offset Saw, Zigzag Discoloration Bubble Silver Break Shrinkage Wash out Lose Print Dot Line Double print Void Stain Word Problem Edge Crack Sliver Dot Lose Printing / Void Contamination Doule Print / Shadow Mark Dot Line Acicular Hole Window offset Window deform Convex
外贸产品不良描述中英文对照
外贸产品不良描述中英文对照Sewing/Textile Product - 缝制品/纺织品bag flap袋盖handle手挽buckle扣clip夹子snap劈啪扣clothes布料drawn string拉绳embroidery刺绣fabric织料hem包边,摺皱key holder锁匙扣lining内衬trap stitches埋线magic sticher魔术贴metal rivet铆钉pocket门袋pocket flap门袋盖rim车边seam缝sew-in label缝内标牌sewing line止口处车线shoulder strap背带strap带zip tie拉链吊尾zipper拉链zipper end拉链尾端zipper head拉链头zipper teeth拉链齿eyelet金属圈/孔眼/透气孔sweat strap(cap)汗带(帽)tail belt(cap)尾带(帽)tail belt buckle(cap)尾带扣(帽)top button(cap)顶珠(帽)visor(cap)帽舌harsh handfeel from dyeing染色不良造成手工粗糙foreign fiber混毛burn out烧焦poor embroidery刺绣不良insufficient stitcher per inch alonghems缝线针脚不够每英寸沿着摺边sewing label incrrect or missing布标固定不良或缺失holes or needle chew scar onsurface表面有碎针孔zipper no function or functionintermittent拉链无功能或功能间歇stitches not straight/wavystitching缝线不直zip sewed in reverse order拉链车反puckered起皱seam open爆口skip stitches跳针broken needle段针back stitches回针broken stitches断车线double/overlapped stitching重车loose stitching车线松missing stitches漏车线poor stitching车线不良stitches of different color thread缝线不同色insufficient stitches per inch along缝线不够密poor thread tension causingpucker缝线过紧引起起皱separation at seam where threadwas visible车缝开裂,缝线可见uneven borders边沿不平整poor trimming修正不良drawn yarn抽纱fabric broken布料烂holes on fabric布料有洞flaws on fabric布料有瑕疵tears on fabric布料破处fabric frayed布料磨损uneven/loose weaving of fabric布料编织不匀称tough to the touch due toexcessive dye染料过多,手感粗糙coarse yarn粗纱needle scar针痕poor hemming包边不良uneven hems包边不平thread color mismatched to fabric线与布料的颜色不搭配care label missing缺说明标签missing promotionaladvertisement paper (if缺广告宣传纸(如果可用)slide snap button no function orfunction intermittent滑动按扣无功能或功能间歇uneven or pulled loops (uncutterry)毛圈不均匀(针对不须切除的毛圈)missing label缺商标dye streaks within fabric布染色条痕slubs on frbric布上有粗结crocking of color磨擦褪色uncut loops (cut terry)毛圈未切除(对需要切的毛圈)General - 家具通用door门drawer抽屉floor地板mirror镜子peg木栓seat cushion座垫rack贮物/冒架shelf架子wood divide分隔木板wood slat木条solid wood实心木plywood / veneer board胶合板vanity带镜的梳妆台staples小钉子rivet铆钉arm rest扶手back rest后靠背castor脚轮gross beam横梁hinge铰链joint / tenon榫头mortise榫眼support stem支柱knot木结back panel后面板side panel侧面板steel seat plate铁座板toe kick脚后座gas lift气动升降装置height adjustable arm高度调节臂ladder梯/梯状物moisture content test湿度测试Wood Product - 木制品bug holes / rodent infestation蛀虫眼moisture content out of limit湿度含量超标bloating发涨poor or missing lacquering喷漆不良/木喷漆Wood T oilet Seat - 木厕座rust or excessive grease on metalcomponents and hardware金属部件生锈或有多余油脂hinges function not smooth铰链滑动不顺rust or poor plating on hinges,rivets or other materials铰链,铆钉或其它金属部件生锈或电镀不良gap between lid seat after closed盖,座间有缝隙(盖下盖后)missing mounting hardware缺装备部件hinges, knobs, bolts, nuts missingor not fit properly铰链,旋钮,门闩,螺帽缺,或不合适Ttools list - 工具列表large slotted screw driver大一字螺丝刀cross screw driver十字螺丝刀small slotted screw driver小一字螺丝刀razor剃刀medium knife中型刀small knife小型刀fish scaler刮鳞刀nail file指甲锉can opener开罐器pliers钳子ceramic stoneware - 陶瓷制品dirt / hair / trash embedded inglaze瓷层内有赃物/毛发/费品sharp points/edge锋利的尖端/锐边non-smooth welds焊接处不光滑excessive visible polishing lines过多的可见抛光纹weld marks a weld points焊接点有焊痕poor finishing at welds焊接表面处理不良rusty spots锈斑weld spark wire residue焊接火星残渣polishing compound residueespecially under the rim and rivets抛光混合物残渣(特别在镶边和铆钉处)unsecured rivets铆钉不牢misalign seam or joint接合处未对齐/对准improper alignment of handles手柄未对齐/对准improper fit of insert pieces to theset一套内置各件大小不合适leakage through the rivets铆钉处渗漏non-stick film thickness exceeded+/-5%不黏膜厚度不符 +/-5%irregullar or rough coating表面涂层粗糙不规则improper or unsecure bonding ofbase底座黏合不适/不牢unsecured fastening未系牢lids fit badly盖子大小不适overburn过烧overlapped重叠poor decal贴花不良poor glazing上釉不良crimping of curves not smooth褶线不平滑individual pieces of sets notmatching in pattern and color每套的单件产品之间图案/颜色不一致design not consistent in pattern ,size and color within and between每套产品的样式,尺寸及颜色设计不一致brass components tarnished (ifapplicable)铜制部件(若有)失去光泽finish not even and with bubblesor flaws抛光不平整,有气泡或瑕疵decorative patterns not consistentincluding color, size andplacement of design修饰图案不一致,包括颜色,尺寸及图案位置decals breakage釉面破裂decals incorrect color花釉颜色错误decals-broken, fizzle, scratch,mis-print花釉有破损,粘花微弱,刮伤,印错decals off position花釉移位/错位pin holes on the item产品上有针孔missinng items缺件missing glaze未上釉glaze not even and with bubblesor flaws釉面不平整,有气泡,瑕疵uneven painting喷涂不均匀damage no the ceramic瓷表面有破损handle not secured in place把手位置不适当unit bottom not polished产品底部未抛光pitted surface, depression onsurface表面有麻点,凹陷thickness of stoneware not eventhroughout the item瓷制产品厚度不均black spots黑斑decal贴花glazing上釉ignition button点火按钮lighter holder打火机固定器Ashtray - 烟灰缸cigarette slot deformed烟槽变形decal off center花釉偏离中心位置unglazed未上釉missing or incomplete decal缺花釉或花釉不全Cutlery - 刀具dinnerware - 餐具dinnerware list餐具列表ceramic dinnerware (pls.refer toceramic product)瓷制餐具(请参考瓷制品缺陷)stainless steel dinnerware不锈钢餐具cookware - 炊具kettle水煲coffee maker咖啡机electrical cookware电炊具Masher/Garlic press - 捣碎器plastic parts do not match intexture or gloss or color塑料部件的文理/光泽/颜色不一致welding lines焊接痕spot weld marks not properlycleaned or polished焊点不整洁/表面处理不良poor fitting of parts , especiallyon the handle and spout部件装配不良,尤其在把手及出口处rusty or corrosive rivets铆钉生锈/已腐蚀handle attachment not in-line withspout手柄和出口不在一条线上rotating handle not rotatedsmoothly手柄旋转不顺畅rotating handle placed in itsupright position not remain手柄不能保持直立Dehumidifier - 干燥器/除湿pre-filter damaged/deformed预滤器(粗滤器)损坏/变形foreign material inside cabinet内有异物poor fitness of water tank水箱大小不合适poor fitness of water hose水龙带大小不合适abnormal noise during operation操作时不正常噪音motor/condenser no function电机/冷凝器无功能indicating lamp no function指示灯无功能Hi-pot test failed高压不过polarity reversed极性接反fuse no function保险丝无功能ground wire discontinuous接地线中断temperature sensing cutoff testfailed温度感应断电测试失败no dehumidifier function无除湿功能live and neutral wires shortage incircuit火线和中线短路tensile pull test for carryinghandle failed把手张力测试失败gap between two halves of theplastic housing塑料机架两半有缝隙brass wire in power cord exposed电源线铜丝外露water full sensing cutoff testfailed水箱满水断电测试失败water tank sensor no function水箱感应器无功能barbecue tools - 烧烤用具lifting pump提升管inlet入水管spout出水管lock nut螺母housing外壳handle手柄poor laser printing激光打印不良deformed of water spouting 出水口变形loose thread螺纹松water leakage漏水failure of the thread test螺纹测试失败failure of the pressure test耐压测试失败handle assembled not in properposition手柄位置安装不当missing sensormatic tag缺防盗标split of water spouting出水偏3failure of the leakage test渗漏测试失败shower head/hand shower - 花office chair - 办公椅caster轮脚arm rest扶手back rest靠背gas lift气棒seat cushion坐垫back support后背支架adjustive handle调节手柄butterfly plate蝴蝶盘leg脚fabric布leather皮stationery - 办公文具caculator计算器ball pen圆珠笔pencil铅笔refill笔芯nib笔头pen holder笔杆pen rack笔架pen cap笔帽pen container笔筒barrel笔身loop hole插笔孔ruler尺stencil镂空尺scissors剪刀cutter裁纸刀tape胶纸tape holder胶纸座glue胶水rubber橡皮擦pencil sharper铅笔消eraser板擦punch打孔机stapler钉书机ridge holderinner sheet内页cover封面memo pad便笺本paper clip纸夹clip board书写板copy holderwhite board白板letter pad信纸本printed film印刷薄膜CE sticker CE标签button closure关闭钮helmet头盔2# HB yellow pencil - 2#HB 黄铅笔burr or scratch on rubber wing橡皮边翼有刮伤和毛刺color of pencil not pantone 123c铅笔颜色对不上色卡号123C poor assembly between twohalves of wood / gap found on木头两半装配不良/铅笔顶端有缝隙graphite center in the wood木头中有石墨missing silkscreen of logo缺丝印标识rubber head assembled in theother end橡皮头装错头paint removed掉漆pin hole on body笔身有针孔wrong logo / name plate mixed inshipment同一船货的标识错误/名称图板相混eraser leaving marks like a red orpink crayon橡皮擦过后留有粉(红)色粉笔似印记pencil lead loose铅笔芯松lead broken铅笔芯断missing core缺铅笔芯Ball Point Pen -圆珠笔obvious shrinkage or deformationon the surface of plastic or metal塑料或金属部件表面有明显的萎缩或变形gap between two halves of theplastic housing塑料笔筒两半之间有缝隙difficult to assemble (ifapplicable)组装困难(若需组装)incorrect instruction / missinginstruction说明书错误/缺失metal and / or mechanical partsrusted金属及/或机械部件生锈pan cap unfit pen body笔帽不配笔身ink not fully filledinterpage corner rolled页卷角line not straight线不直insufficient page页数不够identification lines illegible标识线模糊不清inner sheet torn内页撕裂sheets edge not smooth页边缘不光滑/齐整handle loose out把手松incorrect material composition材料合成不对cannot fit standard size binders不配标准尺寸的活页封cannot open and close smoothly开关不顺/不灵活lock operation not smooth锁功能不顺inner sheet loosened out内页松垮/掉落inner sheet folded内页折叠impurities inside sheet纸内有赃物/杂物sheet surface not smooth页面不光滑Assorted 100 Count ClamshellBox - 哈壳式挖泥机盒blister edge broken吸塑边缘破裂holes on clamshell哈壳上有洞眼sharp edge on clamshell哈壳有锐边incorrect color assortment颜色组合不对excessive gap between cover andbase盖,座间间隙过大steel oxidized钢被氧化Imitation Jewellery - 仿真珠宝necklace项链bracelet手镯brooch胸针beads珠子flat sided beads平边珠子stone石头pearl珍珠pendant坠子snake chain蛇形链ear clip耳夹clasp扣子hook clasp钩扣knot结brooch pin胸针别针link环rubber stop橡皮塞set unevenly not flush to eachother(珠子等)设置不均匀,不整齐resin from... in plating…树脂从...流到…solid bubble in plating电镀表面有固体泡泡porosity on areas of plating电镀区域多孔clasp not open or close properly钩扣开关不顺clasp shift钩扣僵硬不灵blackened surface caused bysolder process焊接过程中造成表面黑话beads not matching in color珠子颜色不匹配beads slided over the knots andhit the next bead珠子滑过接头撞到下一个beads too loosely knotted珠子间间隔太松shading within the beads珠子表面有阴影pin not sharp enough别针不够锋利Clear/colored PlasticBeverageware - 透明/彩色饮料瓶caps/lids帽/盖bases座inner and outer shells内壳/外壳handles手柄thickwalls厚壁bubbles泡泡bubbles grouped in one area泡泡集中在一个区域bubble on lip area嘴唇区域有气泡burned mark烧痕blush脸红carbon spots碳斑carbon spots grouped in one area碳斑集中在一个区域carbob spots on light area碳斑在光亮区域carbon spots on lip area嘴唇区域有碳斑cloudy appearance云彩效果distorted歪曲color streaks/swirls彩色斑纹/旋斑cracking/chipped破裂/有缺口visible dragmark可见的拖痕flow lines on lip area流动线在嘴唇区域flash闪烁sprues注料口oily film油膜orange peel橙色皮orange peel on lip area橙色皮在嘴唇区域yellow tint黄色调warpage战争页Glassware - 玻璃器具glaze not even with bubble orflaws上釉不均,有气泡或瑕疵missing glaze未上釉item did not sitflush(wobbleing/rocking)产品站立不稳(摇晃)decal off position贴花釉位置不对glass shade玻璃灯罩Outdoor articles - 户外用品sleeping bag睡袋Paper Product - 纸制品cover page or inner sheets poorlyglued封面和内页粘贴不良page corner rolled页角卷边flash inside punched holescolor shading difference ondifferent sheets不同页上有不同的彩色阴影line not straight线不直insufficient pages页数不够identification line illegible标识线模糊不清inner sheet torn内页撕裂extra glue residue on sheetsurface表面残留胶水太多inner sheets loosened out内页松垮/掉落wrinkled mark on sheet surface页表面有皱痕distance between lines notidentical行距不一致inner sheet folded内页有摺皱blurred ink mark模糊的墨水印impurities inside sheet纸内有杂斑UPC printed on cover pagescratched封面上的条码有刮伤sheet surface not smooth纸表面不光滑no watermark无水印sheets poorly heat-sealed热收缩密封不良sharp point or sharp edge (injuryto the user)锋利的点或边(会伤害用户)paper chipped纸缺口wrinkled on paper/paper box有皱纹fold line on paper/paperbox/playing card有摺皱pattern on back not consistent(playing card)背面图案组成不对(扑克牌)missing ornaments ontree/poinsettia树/猩猩木上缺装饰物foreign particles inside the base底座内有异物brass wire in power cord exposed电源线铜丝外露motor cannot rotate马达不转abnormal noise in music box (ifapplicable)音乐盒(若有)有异常噪音light cannot extend to fiber opticend灯不能照及光纤末端conduction wires inside thehousing too loose or wire poorly机座内导线过松或整理不良melody/rhythm incorrect旋律/节奏不对bulb broken灯泡破transformer no output变压器无输出功能motor movement too loose马达机芯过松Headset/Earphone - 耳机/听excessive noise噪音过大microphone adjusting arm麦克风调节臂mute button静音钮switch/control开关/控制键bottom foot底角blister broken吸塑破Candle - 蜡烛wax蜡flame火焰peppermint薄荷油wick灯芯scent香味white snowflake like spots点状白色雪片frost mark on surface表面有霜状痕迹caved in on one side一边凹焰wick smoked excessively灯芯冒烟严重flame was small and died out火焰小,逐渐熄灭unscented无香味air bubbles on surface表面有气泡cracked inside内部裂flame burned a tunnel火焰中间烧出一条道wick drowned in melted wax灯芯浸入熔化蜡中wax left on the insides of container容器内粘有蜡Mini blinds - 百叶窗double slats双重窗叶light leakage漏光gap between slats too large窗叶间缝隙太大lock function intermittent锁不住basket ball/foot ball/volleyball/tennis ball - 篮球/足球/排球/网球too much air inside the ball (toohard)气过足ball does not inflate properly充气不良damage no the item/nap no tidy表面绒毛不整齐gift box did not stand in verticalmanner礼篮不能垂直站立not enough air inside the ball (too soft)气不足bouncing height too low/too high球弹高度过底/过高hole in rubber橡皮上有洞poor stitching缝制不良。
产品不良描述-详细中英文对照
CHINESE/中文
間歇功能 貼紙 大聲 其中一功能不良 漏或不足顯示 漏配件 混色 混點 無功能 氧化 剝落 顏料 電鍍 電鍍脫落 毛絨布 角/點 正負极 裝配不良 電鉻不良 電鍍不良 搪膠植毛不良 功能不良 熱燙不良 手腳能動公仔 補油 后面 抵抗 轉動 粗糙 摩擦 走了 生銹 刮花 網/螢幕 螺絲鬆 粘合 線口 車縫 鐵輪 形狀 銳邊/利邊 利角 短電路 縮水 絲 劃形狀 皮 薄的 裂片 細小 弄髒 布類玩具 沾污 焊錫 溶劑 穩定 編法 皮帶鬆 壓力 粘住不能動 塞滿 膨脹 織物結構 穿孔 緊
CATEGORY/分類
GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般 GENERAL/一般
验货缺陷中英文对照
验货缺陷中英文对照DanWang 发表于: 2008-6-06 19:03 来源: 外贸验货员网carton marking wrong/箱唛错carton was damaged/箱烂carton wrinkle/箱邹poor printing on carton/箱唛印刷不良carton marking illegible/箱唛不清楚carton too tight/箱太紧bar code wrong/电脑纹错wrong printing on carton/箱印刷错bar code illegible/电脑纹模糊missing date code/漏日期贴纸missing bar code/漏电脑纹missing vendor code/漏厂编号missing product inside carton./漏装产品carton joint opened/箱驳口开裂carton unsealed/外箱无密封glue mark on carton/外箱胶水印gift box unseal/彩盒无密封gift box crushed/彩盒压烂压皱master carton/外箱shipping carton/落货箱inner carton/内箱blister pack/吸塑袋gift box pack/彩盒袋display box pack/开口彩盒solid pack/独立装assortment pack/混合装bulk pack/散包装cable tie/扎线带shrink warp/吸塑包装whole pack/完整包装bilingual pack/两种语言装gift box dirty/soil/彩盒污糟gift box wrinkle/彩盒皱gift box scratched/彩盒刮伤gift box deformed/dent/彩盒变形/凹陷gift box illegible/彩盒字迹模糊gift box wet/彩盒湿gift box poor sealing/彩盒封口不良gift box unsealed/彩盒无封口gift box flap seam opened/彩盒盖破裂tape poor sticking/胶纸粘贴不良gift box color deviation/彩盒颜色偏差poor printing on gift box/彩盒印刷不良gift box abrasion/彩盒擦伤gift box adhesion/彩盒相粘window box film damaged/彩盒胶窗烂window box film stress/彩盒胶窗顶白window box film dent/彩盒胶窗凹陷window box film detach/彩盒胶窗脱落window box film poor sealing/彩盒胶筒粘合不良window box film poor transparency/彩盒胶袋透明度不够foreign brand model/错型号wrong destination label/错目的地贴纸no suffoca tion warring on poly bag/胶袋无警告字语no recycling mark/无环保贴纸missing serial number/漏号码贴纸serial number don’t correspond/号码与彩盒不符missing label/漏贴纸missing manual/漏说明书missing accessories/漏附件gift box slightly damage/彩盒轻微损坏uneven coloring/颜色不平均illegible printing/印刷模糊wrong/missing coloring/错/漏颜色missing printing/漏印刷字句missing caution tags for transit漏搬运小心贴纸blister card was dirty/soil卡片是肮脏的/土壤insert(cardboakd)wrinkle 皱纹blister card damaged卡片损害blister card incorrect 备置卡片不正确的cardboard color deviationcardboard 彩色偏离shrinkage缩水deformed变形flash/gate remnantmatted无光泽flow line/stress mark夹水纹/顶白poor molding喷塑不良contamination mark混色,混料mark 痕迹,污点,标记colourized 混色color deviation 颜色偏差color mismatched 颜色不配合burnt mark 烧焦痕damaged 烂/损坏poor trimming 修整不良dull surface 哑色poor spraying 喷油不良over spraying 飞油paint under coverage油太薄paint chipped off脱油orange peel painting油面呈橙皮壮foreign painting染油poor re-painting touchup补油不良missing spraying漏喷油dirty on paint surface油面有尘点paint bubbles油泡paint color deviation油颜色偏差paint color mismatched喷油颜色不配合paint abrasion fail油漆被擦paint adhesion fail油漆被甩paint dirty油面污糟spraying scratched喷油刮花dull of paint surface喷油哑色paint matted/frayed喷油无光泽/磨损yellowish painting油面发黄paint peel off油面起皮spraying uneven喷油不整齐paint damped油漆不干paint abrasion甩油bubble冒泡,气泡uneven paint coverage 喷油厚薄,不均paint misregistration错色poor coating油漆外层不良。
外贸专业术语的中英文对照
专业术语翻译辅料ACCESSORY 辅料BINDING TAPE 捆条(包边)BOW 蝴蝶BOW-TIE 蝴蝶结BUTTON 钮扣CARE LABEL 洗水唛CONCEAL ZIPPER 隐形拉链CONTENT LABEL 成分唛ELASTIC 橡筋EYELET 鸡眼LACE 花边LINING 里布MAIN LABEL/BRAND LABEL 主唛PLASTIC STRING 胶针RIBBING 罗纹RUBBER STRING 橡筋SIZE LABEL 尺码唛SMOCKING (装饰用的)缩褶SNAP 急钮, 按钮, 揿钮STICKER 贴纸STRIPE 带条, 绳子THREAD 线VELCRO 魔术贴ZIPPER 拉链ZIPPER PULLER 拉链头车缝(车位:machinist)BACK STITCH 回针/返针BASTING 挑缝BINDING 包边BLIND STITCH 暗线BLIND STITCH MACHINE 盲缝车BLINDING 挑脚BREAK STITCH 断线BUTTONING 钉钮BUTTONING MACHINE 钉钮车DART (死)褶EMBROIDERY 绣花/车花FINAL INSPECTION 尾期检查IN-PROCESS INSPECTION 中期检查IRONING 熨烫LABOUR COST 劳工成本MATERIAL 物料OVERHEAD 厂皮(企业一般管理费)OVERTIME WORKING 加班PIECE RATE 记件工资PRODUCTION SCHEDULE 生产排期PUCKERING 起皱TRIMMING 剪线WRINKLE 不平服,皱褶裁床BIAS CUT 斜纹裁/纵纹裁C.M.T. 来料加工CUTTING TABLE 裁床DIE 刀模DIE CUTTING MACHINE 冲床DRAFTING 绘图DRILLING 钻孔位DRINKING 缩水GRAIN 布纹HAND SHEAR 剪刀SHADING 色差SIZE SPECIFICATION 尺码表QCBROKEN STITCHES 断线BROKEN YARN 断纱COLOR SHADING 色差COLOR THREAD LEFT INSIDE 藏色线COLOR YARN 色纱CREASE MARK 摺痕DIRTY DOT (较小的)污点DIRTY MARK 污渍DIRTY SPOT (较大的)污点DRAW YARN 抽纱FABRIC DEFECTS 布疵KNOT 结头LINING TOO FULL/TIGHT 里布太多/太紧MISMATCH CHECKS/STRIPES 格仔/条子不对称NEEDLE HOLE 针孔OFF GRAIN 布纹歪OIL STAIN 油渍OPEN SEAM 爆口OVERPRESS 熨烫过度OVERWASH 洗水过度PLEATED 打褶POOR BACK-STITCHES 回针不佳POOR IRONING 烫工不良PUCKER 起皱RUBBLING 起泡SCRIMP 印花裂痕SKIPPED STITCHES 跳线THICK YARN 粗纱THREAD VISIBLE OUTSIDE 缝线外露UNCUT THREAD ENDS 线头UNDER THREAD VISIBLE 底线露出UNEVEN COLOR 深浅色WRONG COMBO 颜色组合错误WRONG PATTERN 图案错误WRONG SIZE INDICATED 错码缩写ADL ACCEPTABLE DEFECT LEVEL允许疵点标准AQL ACCEPTABLE QUALITY LEVEL验收合格标准ATTN. ATTENTION 注意AUD. AUDIT 稽查B. BACK 后BK. BLACK 黑色BTN. BUTTON 钮扣C.V.C. CHIEF VALUE OF COTTON 棉为主的混纺物C/B (C.B.) CENTER BACK 后中C/F (C.F.) CENTER FRONT 前中CAD COMPUTER AIDED DESIGN电脑辅助设计CAE COMPUTER AIDED ENGINEERING电脑辅助工程CAL COMPUTER AIDED LAYOUT电脑辅助排料CAM COMPUTER AIDED MANUFACTURE电脑辅助制造CAP COMPUTER AIDED PATTERN电脑辅助画样CI CORPORATE IDENTIFY 企业标识CIF COST, INSURANCE & FREIGHT 到岸价CLR. COLOR 颜色CMT CUTTING, MAKING, TRIMMING 来料加工COL. COLOR 颜色CORD. CORDUROY 灯心绒CS COMMERCIAL STANDARDS 商业标准CTN. COTTON 棉CTN. NO. CARTON NO. 纸箱编号D. & K. DAMAGED & KEPT 染厂对疵布的认赔D.B. DOUBLE-BREASTED 双襟D/Y DELIVERY 出货, 交付DBL DOUBLE 双DBL NDL DOUBLE NEEDLE 双针DEPT. DEPARTMENT 部门DIP 深石洗DK. DARK 深色DOZ. DOZEN 打E.G. EXAMPLI GRATIA / FOR EXAMPLE 例如EMB. EMBROIDERY 绣花, 车花ETC. ET CETERA=AND SO FORTH 等等EXP. EXPORT 出口F. FRONT 前FAB. FABRIC 布料FAQ FAIR AVERAGE QUALITY 中等品FB FREIGHT BILL 装货清单FOB FREE ON BOARD 离岸价FQC FIELD QUALITY CONTROL 现场质量控制FTY. FACTORY 工厂G. GREEN 绿色G.W. GROSS WEIGHT 毛重GL GRAIN LINE 布纹IN. INCH 英寸K KNIT 针织L. LARGE 大号L. LINE 莱尼/号(纽扣大小单位)L. LENGTH 长度L. LEFT 左L.G. LENGTH GRAIN 经向, 直纹LB. POUND 磅LBL LABEL 唛头, 商标LHD LEFT HAND SIDE 左手边LOA LENGTH OVER ALL 全长M MEDIUM 中码M/B MUST BE 必须M/C MACHINE 机械MAT. MATERIAL 物料MEAS. MEASUREMENT 尺寸MKT. MARKET 市场MMTS. MEASUREMENTS 尺寸NDL. NEEDLE 针NIL NOTHING 无O/N ORDER NO. 定单号OS OVER SIZE 超大号OVRLK. OVERLOCK 及骨, 包缝P. PURPLE 紫色P.O. NO. PRODUCTION ORDER NO. 生产制造单编号P.O.B. POST OFFICE BOX 邮箱P.P. PAPER PATTERN 纸样P.S.I. PER SQUARE INCH 每平方英寸P/C POLYESTER/COTTON 涤棉混纺织物PA POLYAMIDE 聚酰胺PB PRIVATE BRAND 个人商标PC. PRICE 价格PCS. PIECES 件, 个PKG. PACKAGE 包装PKT. POCKET 口袋PLS. PLEASE 请PNT POINT 点POS. POSITION 位置PP POLY PROPYLENE 聚丙烯PV POLYVINYL FIBRE 聚乙烯纤维PVC POLYVINYL CHLORIDE 聚氯乙烯QC QUALITY CONTROL 质量控制QLY. QUALITY 质量QPL QUALIFIED PRODUCTS LIST合格产品目录QTY. QUANTITY 数量R. RIGHT 右R.S. RIGHT SIDE 正面R.T.W. READY TO WEAR 成衣REF. REFERENCE 参考, 参照REJ. REJECT 拒绝RM. ROOM 场所S SMALL 小码S/B SHOULD BE 应该SC SHOPPING CENTER 购物中心SGL NDL SINGLE NEEDLE 单针SLV. SLEEVE 袖子SMPL SAMPLE 样板SNL SINGLE 单线SNP SIDE NECK POINT 颈侧点SPEC. SPECIFICATION 细则SQ. FT. SQUARE FEET 平方英尺STY. STYLE 款式SZ. SIZE 尺码T/C TERYLENCE/COTTON 涤棉织物T/S TOP STITCHES 间面线TQC TOTAL QUALITY CONTROL全面质量控制TQM TOTAL QUALITY MANAGEMEN T 全面质量管理V. VIOLET 紫色W WOVEN 梭织W. WAIST 腰围W. WIDTH 宽度WIP半成品W.L. WAIST LINE 腰线W.S. WRONG SIDE 反面WMSP. WORKMANSHIP 手工, 车工WT. WEIGHT 重量X KING SIZE 特大号XL EXTRA LARGE 特大号XXL EXTRA EXTRA LARGE 超特大号Y. YELLOW 黄色YD. YARDAGE 码数面料英语(一)原料纺织原料textile raw materials天然纤维natural fibre化学纤维chemical fibre植物纤维vegetable fibre纺织纤维textile fibre人造纤维man made fibre动物纤维animal fibre(二)面料1.机织物服装面料平纹布plain cloth牛津布oxford斜纹布drill线卡ply-yarn drill哔叽serge灯芯绒corduroy起绒布fleece泡泡纱seersucker麻纱hair cords亚麻布linen cloth绸silk粗纺毛织物woolen cloth全毛单面华达呢woolen one-side gabardine 凡立丁valitine啥味呢twill coating精纺花呢worsted fany suiting法兰绒flannel大衣呢overcoat suiting交织物mixed fabric府绸poplin青年布chambray纱卡single yarn drill华达呢gabardine牛仔布denim平绒velveteen绉布crepe巴厘纱voile苎麻布ramie fabric电力纺habotai精纺毛织物worsted fabric全毛华达呢pure wool gabardine 驼丝锦doeskin女士呢ladies cloth粗花呢tweed2.针织物面料纬编针织物weft-knitted fabric单面针织物single knit fabric纬平针织物plain knit fabric双罗纹针织物interlock fabric起绒针织物interlock fabric毛圈针织物terry knitted fabric 双梳栉经编针织物two-bar fabric 经编针织物warp-knitted fabric双面针织物double knit fabric罗纹针织物rib knit fabric双反面针织物purl fabric长毛绒针织物high pile knitted fabric提花针织物jacquard knitted fabric多梳栉经编针织物multi-bar fabric服装专业英语9(辅料)衬树脂衬resin interlining麻布胸衬breast canvas树脂领衬resin collar interlining绒布胸衬breast fleece热熔衬fusible interlining粘合衬adhesive-bonded interlining双面粘合衬double-faced adhesive interlining 无纺布衬non-woven interlining无纺粘合衬non-woven adhesive interlining 有纺粘合衬adhesive woreninterlinging黑炭衬hair interlining马尾衬horsehair interlining化纤衬chemical fibre interlining针织衬knitted interlining填料棉花cotton人造棉artificial cotton喷胶棉polyester wadding丝棉silk wadding腈纶棉acrylic staple fibre羽绒down3.线、扣、拉链线thread棉线cotton thread丝线silk thread尼龙线nylon thread装饰线ornamental thread钮button四目扣four-hole button装饰纽扣decorative button异形扣special-shaped button塑料扣plastic button玻璃扣glass button子母扣,四合扣snap button拉链zipper尼龙拉链nylon zipper涤纶拉链polyester zipper双头拉链zipper with double sliders 装饰带fashion tape罗纹rib缝纫用线twist麻线flax thread绣花线embroidery thread涤纶线polyester thread宝塔线cone of thread两目扣two-hole button包扣covered button羊角扣claw button金属扣metal button树脂扣resin button木扣wood button尼龙搭扣nylon fastener tape金属拉链metal zipper塑料拉链plastic zipper领钩collar clasp搭钩agraffe橡筋elastic ribbon弹力罗纹elastic ribThe type and name of zipper is given on the basis of the material used in zi pper teeth.拉链类型主要由拉链牙的材质决定Teeth size is expressed by #3-#10 and onwards. #3 representing smaller size t eeth and #10 the larger.牙的尺寸通常是3号-10号,数字越小,尺寸越小。
不良现象中英文对照表
良现象中英文对照表不良现象中英文对照表1.缺件(MISSING PARTS)…missing parts2.错件(WRONG PARTS) wrong parts3.多件(EXCESSIVE PARTS…excessive parts4.短路(SHORT…short5.断路(OPEN)-open6.线短(WIRE SHORT…wire short7.线长(WIRE LONG)…wire long8.拐线(WIRE POOR DDRESS)-wire poor adress9.冷焊(COLD SOLDER)…cold solder10.包焊(EXCESS SOLDER)-excess solder11.空焊(MISSING SOLDER)- missing solder12.锡尖(SOLDER ICICLE) … icicle13.锡渣(SOLDER SPLASH)-• solder splash14.锡裂(SODER CRACK)-solder crack15.锡洞(PIN HOLE)..solder hole16.锡球(SOLDER BALL)..sloder ball17.锡桥(SOLDER BRIDGE…solder bridge18.滑牙(SCREW LOOSE)-screw loose19.氧化(RUST) … rust20.异物(FOREIGNER MATERIAL)-• foreigner material21.溢胶(EXCESSIVE GLUE)22.锡短路(SOLDER BRIDGE)23.锡不足(SOLDER INSUFFICIENT)24.极性反(WRONG POLARITY)25.脚未入(PIN UNSEATED)26.脚未出(PIN UNVISIBLE)27.脚未剪(PIN NO CUT)28.脚未弯(PIN NOT BENT)29.缺盖章(MISSING STAMP)30.缺标签(MISSING LABEL) … missing label31.缺序号(MISSING S/N)32.序号错(WRONG S/N)33.标签错(WRONG LABEL)34.标示错(WRONG MARK)35.脚太短(PIN SHORT)36.J1 不洁(J1 DIRTY)37.锡凹陷(SOLDER SCOOPED)38.线序错(W/L OF WIRE)39.未测试(NO TEST)40.VR 变形(VR DEFORMED]・deformel43.零件沾胶(GLUE ON PARTS)41.PCB 翘皮(PCB PEELING)42.PCB 弯曲(PCB TWIST)44.零件脚长(PARTS PIN LONG)45.浮件(PARTS LIFT)46.零件歪斜(PARTS TILT) ] tilt47.零件相触(PARTS TOUCH)48.零件变形(PARTS DEFORMED)49.零件损坏(PARTS DAMAGED)50.零件脚脏(PIN DIRTY)51.零件多装(PARTS EXCESS)52.零件沾锡(SOLDER ON PARTS)53.零件偏移(PARTS SHIFT)54.包装错误(WRONG PACKING)55.印章错误(WRONG STAMPS)56.尺寸错误(DIMENSION WRONG)57.二极管坏(DIODE NG)58.晶体管坏(TRANSISTOR NG)59.振荡器坏(X'TL NG)60.管装错误(TUBES WRONG)61.阻值错误(IMPEDANCE WRONG])impedance62.版本错误(REV WRONG)63.电测不良(TEST FAILURE)] test failure64.版本未标(NON REV LEBEL)65.包装损坏(PACKING DAMAGED)66.印章模糊(STAMPS DEFECTIVE)67.标签歪斜(LABEL TILT)68.外箱损坏(CARTON DAMAGED])carton damaged69.点胶不良(POOR GLUE)70.IC 座氧化(SOCKET RUST)71.缺UL 标签(MISSING UL LABEL)72.线材不良(WIRE FAILURE)73.零件脚损坏(PIN DAMAGED)74.金手指沾锡(SOLDER ON GOLDEN FINGERS)75.包装文件错(RACKING DOC WRONG)76.包装数量错(PACKING Q'TY WRONG)77.零件未定位(PARTS UNSEATED)78.金手指沾胶(GLUE ON GOLDEN FINGERS)79.垫片安装不良(WASHER UNSEATED])unseat80.线材安装不良(WIRE UNSEATED)81.立碑(TOMBSTONE)。
验货缺陷中英文对译明大全
开关不灵敏
Switch is not sensitive开关Switch /灵敏sensitive
51
指示灯不亮
Indicate lightdead指示Indicate明亮的light灯光lamplight
52
机内有异物
Other object found inside unit/别的Other/目标object/内部inside
71
隔热板掉漆
poor paint on backlite part不好的poor/油漆paint/隔热板backlite/部分part
72
喷水口(管)
spray nozzle喷嘴nozzle
73
装水口
water filling opening开口/洞opening充填物filling
74
旋钮
knob固定holding风叶(扇叶)Fan blades
53
裂缝
Crack明亮brightness
54
开关装配有裂缝
Switch assembly has crack开关Switch /装配assembly /缝隙crack
55
双向电压
Two-way voltage双向Two-way /电压voltage
56
壶漏水
Kettleleakage水壶Kettle /漏水leakage
措施measures /折叠fold /遮盖cover /装饰decorate
117
(坛子,壶)盖子
Lid部分part
118
旋转刀口
turning blade旋转turning /刀口blade布置layout
92
机体歪斜
产品不良英语对照表
产品不良英语对照表aberration 色差atomization ?化bank mark ?料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形 edge切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模。
不良描述中英文对照
不良描述中英文对照Goods Supplement补货1.Plastic parts 塑胶部件Abrasion/划痕、Bubbles/气泡、Burrs/毛刺、Bad Plating/电镀不良、Contamination/杂质、Crack/爆裂、Combine Lines/结合线、Deformation/变形、Flow Marks/流痕、GreasyDirt/油污、Haze/雾状、Jelly/泠胶、Mold Marks/模痕、Melange Color/混色、Oppilation Hole/盲孔、Pull White/拉白、Pour Hole uneven/浇口不平、Wrong Stamping/字麦不符、Short Shots/缺料、Shrinkage/缩水、Stripped Screw/螺丝滑牙、Top White/顶白、Weld Lines/夹水纹、Wrong Dimension/尺寸不符、Wrong Texture/纹理错误、Light/发亮,Gaps裂缝、Steps 披峰、表面有手指印Surface finger prints、丝印错误Wrong printing、丝印偏移Printing slanted、丝印重影Printing double image、丝印有污点,拖尾Printing smearing、丝印不平坦(多油或少油)Printing uneven ( thin / thick )、丝印对于中心偏位Printing off centre、压痕或凹痕Press mark 或dented mark、反光或毛刺Flashing 或 burr、镜片有针孔Pin hole on lens.光泽luster/白点white dot、黑点black dot、装配不合格assembled NG、缺口Nick裂split2.Metal Parts 五金部件Abrasion/划痕、Bad Weld/焊接不良、Burrs/毛刺、Bad Plating/电镀不良、Bend angle/折弯角度、Contamination/杂质、Crack/爆裂、Deformation/变形、Dents/凹痕、Greasy Dirt/油污、Mold Marks/模痕、Missing Stamp/漏冲压、Oppilation Hole/盲孔、Pressing Marks/压痕、Rust/生锈、Wrong Stamping/字麦错误、Short Shots/缺料、Stripped Screw/螺丝滑牙、Pits/疤痕、Specks/斑点、Wrong Texture/纹理错误、Wrong Dimension/尺寸不符3.Painting partsSilkScreen parts 喷油/丝印部件Inspection Points /检查要点 :Bleeding/渗色 ,Bad Painting/喷油不良 ,Contamination/杂质 ,deviate position/偏位 ,Flow Marks/流痕 ,Missing paint/漏喷,Over Paint/肥油 ,Pits/疤痕 ,Poor Adhesion/附着力差 ,Print Words Leans/印刷字体倾斜 ,Pooring Paint/薄油,Silkscreen Haze/丝印模糊 ,Silkscreen Stamping Inconsistency/丝印字样不一致 , Scratch/划伤 ,Speck/斑点 ,Uneven Surface Oil/表面油层不均匀 ,Words Break Off/字体断开 ,Wrong Color/错误颜色 ,Wrong Texture/纹理错误 ;4.PCB 印制线路板Open/开路;Short/短路;Weave Texture/板料席纹;Foreign Residue/外来杂物;Delamination/爆板,分层;Dent/凹陷;Dent on G/F/金手指凹陷;Scratch/擦花;Misregistration/对位不正;Board Damage/板子损坏;C/M Illegible/白字不清;C/M on pad/白字上垫;Copper expoure/露铜;Solder Mask on Pad/绿油上垫;Uneven Solder Mask/绿油不平均;Solder Mask peeling off/绿油脱落;Missing Hole/漏孔;Excess Hole/多孔;Wrong Hole Size/孔径错误;Hole Breakout/崩孔;Nick Trace/线路缺口;Void on Trace/线路铜穿;Diskdown/线路不良/狗牙;Solder Mask inside hole/绿油入孔; Discolouration under Solder Mask/绿油颜色不良; Foreign matter under Solder Mask/绿油下杂物; Solder Mask skipping/不过油;Solder on Gold Finger/金手指上锡;Poor Bevelling/斜边不良;Gold Finger burrs/金手指损坏;Ping Ring/粉红圈5.Electronic parts 电子元件No AVL/没AVL;not on AVL/不在AVL上;Mfg/Mfg P/N dis-match AVL/ 与AVL不符;D/C overdue/ D/C 过期;无D/C;wrong part/错料;no reel/无卷轴;bulk packing for chip/ 散装;No dry packing(HIC change color)/ 无真空包装(防潮卡变色); No ESD packing/无防静电包装;illegible marking/印字不清,wrong marking/印字错;deformation/变型 ;micro crack/裂料;damaged part/ 烂料 ;Lead bent(PTH/SMT)/脚弯;Solder balls damaged/锡球坏wrong lead form/脚型错;wrong pitch/脚距不符;coplanar problem/平整度不良;pad(lead) oxidization/锡垫(引脚)氧化;wrong direction in tape(tray)/带中(盘中)方向错;short pins/引脚短;failed in solderability/ 焊锡不良;size(dimensions) out of specification/ 尺寸超标;function fail/ 功能不良;no tolerance/无误差范围;contamination/杂质;wrong identification for pin1/ 第1脚标识错.Broker Buy/炒料;(巻装物料)巻带前无空余巻带No blank cover tape for feeder loading 巻带粘力不足Not enough adhesive for the cover tape. 料盘变形Reel Deforming/卷带变型.。
外贸验货瑕疵描述
1. Cleanliness(清洁)1 Dirt stains 灰尘污渍2 Oil stains 油污3 Spots 斑点4 Presence of mould or mildew 发霉5 Wet or damp 弄湿或潮湿6 Unpleasant odor 不良气味7 Infestation of insects 有虫子8 Foreign objects 外物9 Needle detected 发现针2. Appearance(外观)1 Poor appearance 外观不良2 Incorrect product 错误的产品3 Poor handfeel 手感不良4 Colour variation 颜色变异5 Inconsistent size 尺寸不一6 Different length 长度不一7 Improper fit 安装不正确8 Loose fit 装配松动9 Deformation of shape 外表变形10 Stress cracks 应力开裂11 Holes or cuts 破洞、切口12 Torn marks 撕裂痕迹13 Colour stains 颜色污渍14 Obvious creases 明显皱纹15 Abrasion marks 摩擦痕迹16 Excessive scuffing 过度插伤17 Excessive scratching 过度刮痕18 Excessive flashing 过度飞边19 Excessive warping 过度扭曲20 Excessive part lines 过度部件分离线21 Obvious wrinkle marks 接缝痕22 Contamination 污染3. Fabric & material1 Fabric flaws 布料瑕疵2 Material deformed 材料变形3 Accessory distorted 附件扭曲4 Frayed edges 破损边缘5 Broken yarns 断纱6 Missing yarns 缺纱7 Pulling yarns 拉纱8 Coarse yarns 粗纱9 Colour yarns 色纱10 Knitting flaws 针织缺陷11 Stop marks 折痕(停车档)12 Dropped needles 掉纱13 Dye streaks 染色痕14 White spots 白点15 Colour bleeding 渗色16 Conspicuously pilling 明显起球17 Bowing 卷边18 Excessive fibre loss 过多纤维损失(掉毛)19 Uneven thickness 厚薄不均4. Stitching1 Monofilament thread used 单丝使用2 Incorrect thread colour 色线颜色错误3 Uncut thread ends 线头4 Floating thread ends 浮动线头5 Poor stitching 不良车线6 Broken stitches 断线7 Missing stitches 漏缝8 Loose stitches 松动的缝线9 Tight stitches 太紧的缝线10 Skipped stitches 跳针11 Run-off stitches 落坑12 Crooked stitches 缝线弯曲13 Inlay stitches exposed 引线暴露14 Poor seaming 不良缝制15 Open seam 爆扣16 Inlay seam exposed 接缝暴露17 Inextensible seam 缝位打卷18 Twisted seam 缝位起扭19 Puckered seam 缝位起皱20 Pleated seam 缝位打褶21 Seams mismatched 错位缝22 Poor embroidery 绣花不良23 Poor buttonhole 锁眼不良5. Workmanship1 Poor workmanship 做工不良2 Missing body part 缺少配件3 Poorly cut 裁剪不良4 Poor fitting 装配不良5 Poor shape 形状不良6 Poor setting 设置不良7 Poorly positioned 位置偏移8 Asymmetrical positioned 错位9 Insecurely fastened 固定不安全10 Conspicuously roping 捆绳痕迹11 Excessive twisting 过多缠绕12 Excessive puckering 过多起褶、起皱13 Conspicuously damage 损坏14 Poor fusing interlining 粘衬不良15 Poor stuffing 填充不良16 Stuffing material exposed 填充物外露17 Incomplete brushing 刷涂不良6. Assembling1 Poor assembling 装配不良2 Cosmetic defects 外观缺陷3 Exposed sharp point or edge 锋利的边缘,尖状物4 Rough surface or edge 粗糙的表面5 Off position 移位6 Position mismatched 错位7 Excessive gap 缝隙过大8 Obvious skewing 明显的偏移9 Poor casting 铸造不良10 Poor cementing 上胶不良11 Poor gluing 点胶不良12 Weak adhesion 粘合不牢固13 Excessive glue marks 过多的胶水痕迹14 Split seams 裂层15 Poor molding 成型不良16 Obvious flow lines 明显的流线17 Gate marks 注塑口胶渍未清理18 Short shot 浇筑,塑胶不足19 Poor book binding 装幁不良20 Poor laminating 分层不良21 Poor welding 焊接不良22 Poor soldering 焊接处不良23 Excessive solder 过多焊接物24 Poor polishing 抛光不良25 Gritty surface 沙面26 Pitted surface 麻面27 Poor screwing 拧螺丝不良28 Missing glitter 缺少闪烁彩粉29 Uneven glitter 彩粉不均匀30 Glitter coming off 彩粉脱落31 Sloppy glitter 闪亮不够32 Hair coming off 毛发脱落33 Uneven trimmed 切边不均匀34 Stiff control button 失效/僵硬的按钮35 Abnormal sound 不正常的声音36 Cords or wires broken 绒/线断开37 Bare wires exposed 裸露的电线38 Wire ends exposed 电线头裸露39 Excessive wobbling 不良摇摆40 Excessive incline 不良的倾斜7. Component & decoration1 Incorrect component 错误的组合2 Incorrect dimension 尺寸不对3 Rust or corrosion 生锈,腐蚀4 Missing components 少配件,少组件5 Decoration coming off 装饰品脱落6 Detached small parts 小部件脱落7 Insecurely fastened 不安全紧固/不牢固8 Conspicuous damage 明显的损坏9 Components deformed 部件变形10 Components misplaced 部件错位11 Components misaligned 部件不对齐12 Component jammed 部件卡塞13 Improper zipper setting 拉链安装不正确14 Visible flow marks 波纹痕迹15 Infestation of wooden parts 蛀虫的木头16 Splinters 碎片17 Dent marks 凹痕18 Burnt marks 烧焦痕19 Fold marks 折痕20 Crumpled marks 皱痕21 Air bubbles 气泡8. Finishing1 Poor finishing 不良完工2 Pressing marks 压痕3 Washing marks 洗水痕4 Poor heat sealing 不良热封胶袋5 Poor hot stamping 烫金不良6 Missing markings 缺少唛标7 Incorrect markings 错误的唛标8 Illegible markings 模糊的唛标9 Failure of plating finish 失败的电镀10 Plating tarnished 电镀失光11 Plating colour deviated 电镀颜色差异12 Flaking of plating 电镀层脱落13 Blisters 水泡14 Poor painting 油漆不良15 Failure of painting 失败的油漆/涂漆16 Paint colour deviated 油漆颜色偏离17 Paint peeling off 油漆层剥落18 Obvious touch-up painting 明显的修补油漆19 Failure of paint spraying 失败的喷漆20 Obvious scratched marks 明显的划痕21 Failure of coating finish 失败的涂层22 Sloppy coating 不良涂层23 Failure of varnishing finish 失败的扫油24 Failure of lacquering finish 失败的涂漆层25 Failure of printing 失败的印花26 Printing colour deviated 印花颜色偏离27 Printing colour blocked 印花网板被堵28 Vague printing 模糊印花29 Failure of glazing 失败的上釉30 Uneven glaze 上釉不均匀31 Failure of decal 釉花纸不良9. Performance1 Malfunction of mechanism 原理故障2 Intermittent function of mechanism 间接性故障3 Poor function of mechanism 功能不良4 Leakage 泄漏5 Temperature over heat 温度过热6 Poor connection 连接不良7 Poor adjustment 调节器不良8 Cannot hold position 不能固定位置10. Labeling & packaging1 Products mixed-up 混装2 Wrong packaging 错误的包装3 Missing or incorrect labels 错误的标签/贴标4 Soils 尘土5 Conspicuous damage 明显的损坏6 Poorly positioned 不良位置7 Insecure closure 不牢固的闭合8 Excessive crumpled marks 过多褶皱痕9 Missing printing or markings 漏印唛头10 Incorrect printing or markings 错印唛头11 Illegible printing or markings 模糊唛头12 Missing packaging material 缺少包装材料13 Poor presentation of packaging 错误包装方法。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
Sewing/Textile Product - 缝制品/纺织品bag flap袋盖handle手挽buckle扣clip夹子snap劈啪扣clothes布料drawn string拉绳embroidery刺绣fabric织料hem包边,摺皱key holder锁匙扣lining内衬trap stitches埋线magic sticher魔术贴metal rivet铆钉pocket门袋pocket flap门袋盖rim车边seam缝sew-in label缝内标牌sewing line止口处车线shoulder strap背带strap带zip tie拉链吊尾zipper拉链zipper end拉链尾端zipper head拉链头zipper teeth拉链齿eyelet金属圈/孔眼/透气孔sweat strap(cap)汗带(帽)tail belt(cap)尾带(帽)tail belt buckle(cap)尾带扣(帽)top button(cap)顶珠(帽)visor(cap)帽舌harsh handfeel from dyeing染色不良造成手工粗糙foreign fiber混毛burn out烧焦poor embroidery刺绣不良insufficient stitcher per inch alonghems缝线针脚不够每英寸沿着摺边sewing label incrrect or missing布标固定不良或缺失holes or needle chew scar onsurface表面有碎针孔zipper no function or functionintermittent拉链无功能或功能间歇stitches not straight/wavystitching缝线不直zip sewed in reverse order拉链车反puckered起皱seam open爆口skip stitches跳针broken needle段针back stitches回针broken stitches断车线double/overlapped stitching重车loose stitching车线松missing stitches漏车线poor stitching车线不良stitches of different color thread缝线不同色insufficient stitches per inch along缝线不够密poor thread tension causingpucker缝线过紧引起起皱separation at seam where threadwas visible车缝开裂,缝线可见uneven borders边沿不平整poor trimming修正不良drawn yarn抽纱fabric broken布料烂holes on fabric布料有洞flaws on fabric布料有瑕疵tears on fabric布料破处fabric frayed布料磨损uneven/loose weaving of fabric布料编织不匀称tough to the touch due toexcessive dye染料过多,手感粗糙coarse yarn粗纱needle scar针痕poor hemming包边不良uneven hems包边不平thread color mismatched to fabric线与布料的颜色不搭配care label missing缺说明标签missing promotionaladvertisement paper (if缺广告宣传纸(如果可用)slide snap button no function orfunction intermittent滑动按扣无功能或功能间歇uneven or pulled loops (uncutterry)毛圈不均匀(针对不须切除的毛圈)missing label缺商标dye streaks within fabric布染色条痕slubs on frbric布上有粗结crocking of color磨擦褪色uncut loops (cut terry)毛圈未切除(对需要切的毛圈)General - 家具通用door门drawer抽屉floor地板mirror镜子peg木栓seat cushion座垫rack贮物/冒架shelf架子wood divide分隔木板wood slat木条solid wood实心木plywood / veneer board胶合板vanity带镜的梳妆台staples小钉子rivet铆钉arm rest扶手back rest后靠背castor脚轮gross beam横梁hinge铰链joint / tenon榫头mortise榫眼support stem支柱knot木结back panel后面板side panel侧面板steel seat plate铁座板toe kick脚后座gas lift气动升降装置height adjustable arm高度调节臂ladder梯/梯状物moisture content test湿度测试Wood Product - 木制品bug holes / rodent infestation蛀虫眼moisture content out of limit湿度含量超标bloating发涨poor or missing lacquering喷漆不良/木喷漆Wood Toilet Seat - 木厕座rust or excessive grease on metalcomponents and hardware金属部件生锈或有多余油脂hinges function not smooth铰链滑动不顺rust or poor plating on hinges,rivets or other materials铰链,铆钉或其它金属部件生锈或电镀不良gap between lid seat after closed盖,座间有缝隙(盖下盖后)missing mounting hardware缺装备部件hinges, knobs, bolts, nuts missingor not fit properly铰链,旋钮,门闩,螺帽缺,或不合适Ttools list - 工具列表large slotted screw driver大一字螺丝刀cross screw driver十字螺丝刀small slotted screw driver小一字螺丝刀razor剃刀medium knife中型刀small knife小型刀fish scaler刮鳞刀nail file指甲锉can opener开罐器pliers钳子ceramic stoneware - 陶瓷制品dirt / hair / trash embedded inglaze瓷层内有赃物/毛发/费品sharp points/edge锋利的尖端/锐边non-smooth welds焊接处不光滑excessive visible polishing lines过多的可见抛光纹weld marks a weld points焊接点有焊痕poor finishing at welds焊接表面处理不良rusty spots锈斑weld spark wire residue焊接火星残渣polishing compound residueespecially under the rim and rivets抛光混合物残渣(特别在镶边和铆钉处)unsecured rivets铆钉不牢misalign seam or joint接合处未对齐/对准improper alignment of handles手柄未对齐/对准improper fit of insert pieces to theset一套内置各件大小不合适leakage through the rivets铆钉处渗漏non-stick film thickness exceeded+/-5%不黏膜厚度不符 +/-5%irregullar or rough coating表面涂层粗糙不规则improper or unsecure bonding ofbase底座黏合不适/不牢unsecured fastening未系牢lids fit badly盖子大小不适overburn过烧overlapped重叠poor decal贴花不良poor glazing上釉不良crimping of curves not smooth褶线不平滑individual pieces of sets notmatching in pattern and color每套的单件产品之间图案/颜色不一致design not consistent in pattern ,size and color within and between每套产品的样式,尺寸及颜色设计不一致brass components tarnished (ifapplicable)铜制部件(若有)失去光泽finish not even and with bubblesor flaws抛光不平整,有气泡或瑕疵decorative patterns not consistentincluding color, size andplacement of design修饰图案不一致,包括颜色,尺寸及图案位置decals breakage釉面破裂decals incorrect color花釉颜色错误decals-broken, fizzle, scratch,mis-print花釉有破损,粘花微弱,刮伤,印错decals off position花釉移位/错位pin holes on the item产品上有针孔missinng items缺件missing glaze未上釉glaze not even and with bubblesor flaws釉面不平整,有气泡,瑕疵uneven painting喷涂不均匀damage no the ceramic瓷表面有破损handle not secured in place把手位置不适当unit bottom not polished产品底部未抛光pitted surface, depression onsurface表面有麻点,凹陷thickness of stoneware not eventhroughout the item瓷制产品厚度不均black spots黑斑decal贴花glazing上釉ignition button点火按钮lighter holder打火机固定器Ashtray - 烟灰缸cigarette slot deformed烟槽变形decal off center花釉偏离中心位置unglazed未上釉missing or incomplete decal缺花釉或花釉不全Cutlery - 刀具dinnerware - 餐具dinnerware list餐具列表ceramic dinnerware (pls.refer toceramic product)瓷制餐具(请参考瓷制品缺陷)stainless steel dinnerware不锈钢餐具cookware - 炊具kettle水煲coffee maker咖啡机electrical cookware电炊具Masher/Garlic press - 捣碎器plastic parts do not match intexture or gloss or color塑料部件的文理/光泽/颜色不一致welding lines焊接痕spot weld marks not properlycleaned or polished焊点不整洁/表面处理不良poor fitting of parts , especiallyon the handle and spout部件装配不良,尤其在把手及出口处rusty or corrosive rivets铆钉生锈/已腐蚀handle attachment not in-line withspout手柄和出口不在一条线上rotating handle not rotatedsmoothly手柄旋转不顺畅rotating handle placed in itsupright position not remain手柄不能保持直立Dehumidifier - 干燥器/除湿pre-filter damaged/deformed预滤器(粗滤器)损坏/变形foreign material inside cabinet内有异物poor fitness of water tank水箱大小不合适poor fitness of water hose水龙带大小不合适abnormal noise during operation操作时不正常噪音motor/condenser no function电机/冷凝器无功能indicating lamp no function指示灯无功能Hi-pot test failed高压不过polarity reversed极性接反fuse no function保险丝无功能ground wire discontinuous接地线中断temperature sensing cutoff testfailed温度感应断电测试失败no dehumidifier function无除湿功能live and neutral wires shortage incircuit火线和中线短路tensile pull test for carryinghandle failed把手张力测试失败gap between two halves of theplastic housing塑料机架两半有缝隙brass wire in power cord exposed电源线铜丝外露water full sensing cutoff testfailed水箱满水断电测试失败water tank sensor no function水箱感应器无功能barbecue tools - 烧烤用具lifting pump提升管inlet入水管spout出水管lock nut螺母housing外壳handle手柄poor laser printing激光打印不良deformed of water spouting出水口变形loose thread螺纹松water leakage漏水failure of the thread test螺纹测试失败failure of the pressure test耐压测试失败handle assembled not in properposition手柄位置安装不当missing sensormatic tag缺防盗标split of water spouting出水偏3failure of the leakage test渗漏测试失败shower head/hand shower - 花office chair - 办公椅caster轮脚arm rest扶手back rest靠背gas lift气棒seat cushion坐垫back support后背支架adjustive handle调节手柄butterfly plate蝴蝶盘leg脚fabric布leather皮stationery - 办公文具caculator计算器ball pen圆珠笔pencil铅笔refill笔芯nib笔头pen holder笔杆pen rack笔架pen cap笔帽pen container笔筒barrel笔身loop hole插笔孔ruler尺stencil镂空尺scissors剪刀cutter裁纸刀tape胶纸tape holder胶纸座glue胶水rubber橡皮擦pencil sharper铅笔消eraser板擦punch打孔机stapler钉书机ridge holderinner sheet内页cover封面memo pad便笺本paper clip纸夹clip board书写板copy holderwhite board白板letter pad信纸本printed film印刷薄膜CE sticker CE标签button closure关闭钮helmet头盔2# HB yellow pencil - 2#HB 黄铅笔burr or scratch on rubber wing橡皮边翼有刮伤和毛刺color of pencil not pantone 123c铅笔颜色对不上色卡号123Cpoor assembly between twohalves of wood / gap found on木头两半装配不良/铅笔顶端有缝隙graphite center in the wood木头中有石墨missing silkscreen of logo缺丝印标识rubber head assembled in theother end橡皮头装错头paint removed掉漆pin hole on body笔身有针孔wrong logo / name plate mixed inshipment同一船货的标识错误/名称图板相混eraser leaving marks like a red orpink crayon橡皮擦过后留有粉(红)色粉笔似印记pencil lead loose铅笔芯松lead broken铅笔芯断missing core缺铅笔芯Ball Point Pen -圆珠笔obvious shrinkage or deformationon the surface of plastic or metal塑料或金属部件表面有明显的萎缩或变形gap between two halves of theplastic housing塑料笔筒两半之间有缝隙difficult to assemble (ifapplicable)组装困难(若需组装)incorrect instruction / missinginstruction说明书错误/缺失metal and / or mechanical partsrusted金属及/或机械部件生锈pan cap unfit pen body笔帽不配笔身ink not fully filledinterpage corner rolled页卷角line not straight线不直insufficient page页数不够identification lines illegible标识线模糊不清inner sheet torn内页撕裂sheets edge not smooth页边缘不光滑/齐整handle loose out把手松incorrect material composition材料合成不对cannot fit standard size binders不配标准尺寸的活页封cannot open and close smoothly开关不顺/不灵活lock operation not smooth锁功能不顺inner sheet loosened out内页松垮/掉落inner sheet folded内页折叠impurities inside sheet纸内有赃物/杂物sheet surface not smooth页面不光滑Assorted 100 Count ClamshellBox - 哈壳式挖泥机盒blister edge broken吸塑边缘破裂holes on clamshell哈壳上有洞眼sharp edge on clamshell哈壳有锐边incorrect color assortment颜色组合不对excessive gap between cover andbase盖,座间间隙过大steel oxidized钢被氧化Imitation Jewellery - 仿真珠宝necklace项链bracelet手镯brooch胸针beads珠子flat sided beads平边珠子stone石头pearl珍珠pendant坠子snake chain蛇形链ear clip耳夹clasp扣子hook clasp钩扣knot结brooch pin胸针别针link环rubber stop橡皮塞set unevenly not flush to eachother(珠子等)设置不均匀,不整齐resin from... in plating…树脂从...流到…solid bubble in plating电镀表面有固体泡泡porosity on areas of plating电镀区域多孔clasp not open or close properly钩扣开关不顺clasp shift钩扣僵硬不灵blackened surface caused bysolder process焊接过程中造成表面黑话beads not matching in color珠子颜色不匹配beads slided over the knots andhit the next bead珠子滑过接头撞到下一个beads too loosely knotted珠子间间隔太松shading within the beads珠子表面有阴影pin not sharp enough别针不够锋利Clear/colored PlasticBeverageware - 透明/彩色饮料瓶caps/lids帽/盖bases座inner and outer shells内壳/外壳handles手柄thickwalls厚壁bubbles泡泡bubbles grouped in one area泡泡集中在一个区域bubble on lip area嘴唇区域有气泡burned mark烧痕blush脸红carbon spots碳斑carbon spots grouped in one area碳斑集中在一个区域carbob spots on light area碳斑在光亮区域carbon spots on lip area嘴唇区域有碳斑cloudy appearance云彩效果distorted歪曲color streaks/swirls彩色斑纹/旋斑cracking/chipped破裂/有缺口visible dragmark可见的拖痕flow lines on lip area流动线在嘴唇区域flash闪烁sprues注料口oily film油膜orange peel橙色皮orange peel on lip area橙色皮在嘴唇区域yellow tint黄色调warpage战争页Glassware - 玻璃器具glaze not even with bubble orflaws上釉不均,有气泡或瑕疵missing glaze未上釉item did not sitflush(wobbleing/rocking)产品站立不稳(摇晃)decal off position贴花釉位置不对glass shade玻璃灯罩Outdoor articles - 户外用品sleeping bag睡袋Paper Product - 纸制品cover page or inner sheets poorlyglued封面和内页粘贴不良page corner rolled页角卷边flash inside punched holescolor shading difference ondifferent sheets不同页上有不同的彩色阴影line not straight线不直insufficient pages页数不够identification line illegible标识线模糊不清inner sheet torn内页撕裂extra glue residue on sheetsurface表面残留胶水太多inner sheets loosened out内页松垮/掉落wrinkled mark on sheet surface页表面有皱痕distance between lines notidentical行距不一致inner sheet folded内页有摺皱blurred ink mark模糊的墨水印impurities inside sheet纸内有杂斑UPC printed on cover pagescratched封面上的条码有刮伤sheet surface not smooth纸表面不光滑no watermark无水印sheets poorly heat-sealed热收缩密封不良sharp point or sharp edge (injuryto the user)锋利的点或边(会伤害用户)paper chipped纸缺口wrinkled on paper/paper box有皱纹fold line on paper/paperbox/playing card有摺皱pattern on back not consistent(playing card)背面图案组成不对(扑克牌)missing ornaments ontree/poinsettia树/猩猩木上缺装饰物foreign particles inside the base底座内有异物brass wire in power cord exposed电源线铜丝外露motor cannot rotate马达不转abnormal noise in music box (ifapplicable)音乐盒(若有)有异常噪音light cannot extend to fiber opticend灯不能照及光纤末端conduction wires inside thehousing too loose or wire poorly机座内导线过松或整理不良melody/rhythm incorrect旋律/节奏不对bulb broken灯泡破transformer no output变压器无输出功能motor movement too loose马达机芯过松Headset/Earphone - 耳机/听excessive noise噪音过大microphone adjusting arm麦克风调节臂mute button静音钮switch/control开关/控制键bottom foot底角blister broken吸塑破Candle - 蜡烛wax蜡flame火焰peppermint薄荷油wick灯芯scent香味white snowflake like spots点状白色雪片frost mark on surface表面有霜状痕迹caved in on one side一边凹焰wick smoked excessively灯芯冒烟严重flame was small and died out火焰小,逐渐熄灭unscented无香味air bubbles on surface表面有气泡cracked inside内部裂flame burned a tunnel火焰中间烧出一条道wick drowned in melted wax灯芯浸入熔化蜡中wax left on the insides ofcontainer容器内粘有蜡Mini blinds - 百叶窗double slats双重窗叶light leakage漏光gap between slats too large窗叶间缝隙太大lock function intermittent锁不住basket ball/foot ball/volleyball/tennis ball - 篮球/足球/排球/网球too much air inside the ball (toohard)气过足ball does not inflate properly充气不良damage no the item/nap no tidy表面绒毛不整齐gift box did not stand in verticalmanner礼篮不能垂直站立not enough air inside the ball (toosoft)气不足bouncing height too low/too high球弹高度过底/过高hole in rubber橡皮上有洞poor stitching缝制不良。