贝加莱伺服报警
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
NC Error Text Table : acpex
acpex.waf [NC Error Text Table]
ID Text
acp10 version 1.050
Error strings
1、Parameter ID invalid
参数ID号无效。
2、Parameter can not be read (value is not available at the moment)
参数不能读(数值在当时不能用)。
3、Write access for a read only parameter
对只读参数进行写操作。
4 、Read access for a write only parameter
对只写参数进行读操作。
5 、Value of parameter is invalid
参数数值无效。
REAL Value of Parameter
参数的实数值。
6 、Value of parameter is invalid
参数数值无效。
UDINT Value of Parameter
参数的无符号长整数值。
7、Value of parameter is invalid
参数数值无效。
DINT Value of Parameter
参数的长整数值。
8 、Data block read access already initialized
读数据块操作,已经初始化了。
9 、Data block write access already initialized
写数据块操作,已经初始化了。
10 、Data block read access not initialized
读数据块操作,还没有初始化。
11 、Data block write access not initialized
写数据块操作,还没有初始化。
12、Data block write access still active (INIT for read access not possible)
数据块正在进行写操作,(初始化读操作不允许)
13 、Data block read access still active (INIT for write access not possible)
数据块正在进行读操作,(初始化写操作不允许)
14 、Timeout for Read Response
读响应超时
15 、Timeout for Write Response
写响应超时
16 The Data segment at data block read is already the last
要读的数据段已经是数据块的尾部。
17 The Data segment at data block write is already the last
要写的数据段已经是数据块的尾部。
18 The Data segment at data block read is not yet the last
要读的数据段没有在数据块的尾部。
UDINT Data block offset
数据段在数据块的偏移地址。
19 The Data segment at data block write is not yet the last
要写的数据段没有在数据块的尾部。
UDINT Data block offset
数据段在数据块的偏移地址。
20 Checksum after data block read is invalid
读数据块后,校验和无效。
21 Checksum after data block write is invalid
写数据块后,校验和无效。
22 Parameter ID in data block is invalid (data block read)
在数据块中参数ID号无效(读数据块时)
'PARID' Parameter ID
错误的参数ID号
23 Parameter ID in data block is invalid (data block write)
在数据块中参数ID号无效(写数据块时)
'PARID' Parameter ID
错误的参数ID号
24 System module download not allowed in this boot state
在引导状态不允许下载系统模块
UINT Boot state
引导状态号
25 Burn system module only allowed immediately after download
将系统模块烧到EEROM,必须在下载后立即执行
26 Requested change of boot state is not allowed in this boot state
在该引导状态下不允许修改引导状态
UINT Boot state
当前引导状态
27 Start of operating system not possible (operating system is not on the FPROM)
不能启动操作系统(FPROM没有操作系统)
28 Read parameter not allowed in this drive state
在当前驱动状态,不能读参数
UINT Drive state
当前驱动状态
29 Write parameter not allowed in this drive state
在当前驱动状态,不能写参数
UINT Drive state
当前驱动状态
30 Read parameter not possible because of hardware error
由于硬件错误,不能读参数。
UINT Hardware error
当前硬件错误
31 Write parameter not possible because of hardware error
由于硬件错误,不能写参数。
UINT Hardware error
当前硬件错误
32 Command parameter is invalid
命令参数无效
'PARID' Parameter ID
无效的命令参数
40 Value of parameter higher than maximum value
参数数值超过最大值。
REAL Maximum value
该参数最大值(实数)
41 Value of parameter higher than maximum value
参数数值超过最大值。
UDINT Maximum value
该参数最大值(无符号长整型)
42 Value of parameter higher than maximum value
参数数值超过最大值。
DINT Maximum value
该参数最大值(长整型)