MDU配置举例脚本

说明：一个gemport匹配一个CVLAN，MDU的宽带CVLAN均是101-124，按端口分配；而且语音VLAN和网管VLAN均占用一个gemport，所以一台MDU需要在OLT上建立26个gemport，在同一个PON口下，gemport ID是唯一的。

GEMPORT从129开始计算，第一个给网管VLAN，第二个给语音VLAN，后24个给宽带VLAN，所以按不同MDU gemport计算可按公式，129+n*26+(0到25)，n可以做为ONTID。

场景设置:MA5680T下带MA5620G，ONTID为0；网管VLAN为100，语音VLAN为1000，宽带SVLAN为1421，CVLAN为101-124；MA5680T网管IP地址：192.168.1.1，MA5620G网管IP地址为192.168.1.2；MA5620G语音IP地址：192.168.2.3，PBX语音网关IP地址：192.168.2.1，SIP端口号均为5060；网管gemport id=129，语音gemport id=130，宽带gemport id=131-154宽带用户带宽为上行8M，下行16M；MA5680T：建立ONT模板：MA5680T(config)#ont-profile add gpon profile-id 17{ <cr>|profile-name<K> }:Command:ont-profile add profile-id 17Press 'Q' or 'q' to quit input> Number of uplink PON ports<1-2> [1]:1> IP config mode<0-Nonsupport, 1-Support, 2-DHCP only, 3-Static only> [1]:3> The type of MAC bridge<1-Single,2-Multi> [1]:1> Number of GEM ports<1-32> [32]: 32> Is UNI configuration concerned<1-not concern, 2-concern> [1]:1> Mapping mode<1-VLANID, 2-802_1pPRI, 3-VLANID_802_1pPRI, 9-IPTOS,10-VLANID_IPTOS> [1]:1> Number of T-CONTs<1-8> [1]:8> The type of flow control<1-PQ, 2-GEMPORT-CAR, 3-FLOW-CAR> [1]:3MA5680T(config)# ont resume resource resume//进行强制匹配MA5680T(config)#interface gpon 0/1MA5680T(config-if-gpon-0/1)#port{ portid<U><0,3> }:0{ range<K>|laser-switch<K>|ont-password-renew<K>|ont-auto-find<K>|fec<K> }:ont-a uto-find{ switch<E><enable,disable> }:enableCommand: port 0 ont-auto-find enable//打开0/1/0 PON口端口自动发现功能MA5680T(config-if-gpon-0/1)#! EVENT WARNING 2009-02-06 18:35:35 ALARM NAME :The Auto-find ONU's password is invalid PARAMETERS :FrameID: 0, SlotID: 1, PortID: 0, SN: 32303131B6072A41, Password(ASCII): FFFFFFFFFFFFFFFFFFFF MA5680T(config-if-gpon-0/1)#! EVENT WARNING 2009-02-06 18:35:35 ALARM NAME :ONU in Auto-find state alarm PARAMETERS :FrameID: 0, SlotID: 1, PortID: 0, SN: 32303131B6072A41, Password: - 如光路没问题，PON口ID为0的端口下带的MDU上电后会自动上报一个SN码，通过此码进行注册。

MA5680T(config-if-gpon-0/1)# ont confirm{ portid<U><0,3> }:0{ all<K>|ontid<K>|password-auth<K>|sn-auth<K> }:sn-auth{ sn<S><13,16> }:32303131B6072A41 （上面上报的SN码）{ password-auth<K>|profile-id<K>|profile-name<K> }:profile-id{ profile-id<U><1,128> }:17{ <cr>|description<K>|manage-mode<K> }: Command: ont confirm 1 sn-auth 32303131B606ED41 profile-id 17 //针对SN码为32303131B6072A41的MDU，通过ONT能力集模板17来注册MDU正常注册后的MDU可以通过命令来查看是否正常MA5680T(config-if-gpon-0/1)#display ont info 0 all//查看0/1/0下所有ONT注册情况Command: display ont info 0 all ----------------------------------------------------------------------------- F/S/P ONT-ID MAC Control Run Config Match LoopBack Flag State State State State ----------------------------------------------------------------------------- 0/1/0 0 XXXXXXXXXXX active up normal match disable ----------------------------------------------------------------------------- In port 0, the total of ONTs are: 1配置Tcont模板：MA5680T(config)# dba-profile{ add<K>|delete<K>|modify<K> }:add{ profile-id<K>|profile-name<K>|type1<K>|type2<K>|type3<K>|type4<K>|type5<K> }:p rofile-id{ profile-id<U><10,512> }:10{ type1<K>|profile-name<K>|type2<K>|type3<K>|type4<K>|type5<K> }:type2{ assure<K> }:assure{ assure-bandwidth<U><512,1235456> }:24576Command: dba-profile add profile-id 10 type2 assure 24576 //配置宽带上行保证总带宽为24M，按一个用户上行6152K，24个用户，收敛比1：6MA5680T(config)#dba-profile add profile-id 11 type2 assure 2048//配置窄带上行保证带宽为2MMA5680T(config)#dba-profile add profile-id 12 type2 assure 2048//配置网管上行保证带宽为2M网管业务：OLT侧数据：MA5680T(config)#vlan 100 smart //配置网管VLAN 100MA5680T(config)#port vlan 100 0/20 0 //指定0/20/0端口允许VLAN 100上行通过MA5680T(config)#interface vlanif 100MA5680T(config-if-vlanif100)#ip address 192.168.1.1{ ip_addr<I><X.X.X.X>|integer<U><0,32> }:24{ <cr>|sub<K> }://配置网管IP地址MA5680T(config-if-gpon-0/1)#ont ipconfig 0{ ontid<U><0,63> }:0{ dhcp<K>|static<K> }:static{ ip-address<K>|gateway<K>|pri-dns<K>|slave-dns<K> }:ip-address{ ip-address<I><X.X.X.X> }:192.168.1.2{ mask<K> }:mask{ mask(A.B.C.D)<M><X.X.X.X> }:255.255.255.0{ <cr>|gateway<K>|pri-dns<K>|slave-dns<K> }:Command:ont ipconfig 0 0 static ip-address 192.168.1.4 mask 255.255.255.0MA5680T(config-if-gpon-0/1)#The configuration of ONT IP is successful//在MA5680T上远程配置MA5620G的网管IP地址MA5680T(config-if-gpon-0/1)#ont port vlan{ portid<U><0,3> }:0{ ontid<U><0,63> }:0{ iphost<K>|fe<K>|ge<K>|moca<K> }:iphost{ vlanid<U><0,4095> }:100Command:ont port vlan 0 0 iphost 100MA5680T(config-if-gpon-0/1)#Add ports to the VLAN, total: 1, discarded: 0, success: 1, failed: 0//在MA5680T上远程配置MA5620G网管VLAN 100MA5680T(config-if-gpon-0/1)#tcont bind-profile{ portid<U><0,3> }:0{ ontid<U><0,63> }:0{ tcont-list<S><1,13> }:1//id从1开始，0固定为OMCI通道占用{ profile-id<K>|profile-name<K> }:profile-id{ profile-id<U><1,512> }:12Command:tcont bind-profile 0 0 1 profile-id 12MA5680T(config-if-gpon-0/1)#Binding a DBA-profile succeeded//tcont绑定网管业务的DBA模板MA5680T(config-if-gpon-0/1)#gemport add{ portid<U><0,3> }:0{ gemportid<K>|gemport-num<K> }:gemportid{ gemportlist<S><3,159> }:129{ service-type<E><eth,tdm> }:eth{ <cr>|encrypt<K>|cascade<K> }:Command:gemport add 0 gemportid 129 ethMA5680T(config-if-gpon-0/1)#Adding a GEM port succeeded//建立gemportMA5680T(config-if-gpon-0/1)#ont gemport bind{ portid<U><0,3> }:0{ ontid<U><0,63> }:0{ gemport-list<S><3,159> }:129{ tcont-id<U><0,7> }:1{ priority-queue<K>|gemport-car<K>|flow-car<K> }:flow-carCommand:ont gemport bind 0 0 129 1 flow-carMA5680T(config-if-gpon-0/1)#The GEM port(s) bind the T-CONT successfully//配置gemport 129跟tcont id 1绑定，MA5680T(config-if-gpon-0/1)#ont gemport mapping{ portid<U><0,3> }:0{ ontid<U><0,63> }:0{ gemportid<U><128,3999> }:129{ vlan<K>|priority<K>|fe<K>|ge<K>|moca<K>|iphost<K>|e1<K> }:vlan { vlan-id<U><0,4095> }:100{ averband<U><64,1048576>|priority<K>|<cr> }:2048{ maxband<U><64,1048576> }:2048Command:ont gemport mapping 0 0 129 vlan 100 2048 2048MA5680T(config-if-gpon-0/1)#Add the GEM port mapping successfully//匹配id为129的gemport和MDU上行的网管VLAN 100MA5680T(config)#service-port vlan 100{ adsl<K>|shdsl<K>|vdsl<K>|atm<K>|eth<K>|gpon<K>|epon<K> }:gpon{ frameid/slotid/portid<S><1,15> }:0/1/0{ gemport<K> }:gemport{ gemportid<U><128,3999> }:129{ rx-cttr<K>|multi-service<K> }:multi-service{ user-vlan<K>|user-encap<K>|user-8021p<K> }:user-vlan{ untagged<K>|user-vlanid<U><1,4095>|priority-tagged<K>|other-all<K> }:100{ rx-cttr<K> }:rx-cttr 6 tx-cttr 6Command:service-port vlan 100 gpon 0/1/0 gemport 129 multi-service user-vlan 100 rx-cttr 6 tx-cttr 6//通过service port建立一个虚通道，透传MDU的网管VLAN 100，使用的流量模板ID为6（默认不限制）配置完上列数据后，MA5620G的网管数据通过MA5680T已下发完毕，MA5680T的数据和通道已配置完毕，所以MA5680T可以ping通MA5620G的网管地址，并可以远程登陆配置MDU数据。