漏水传感器说明书(常闭)7.19号
艾默生 3A7114D QUANTM 泄漏传感器 安装手册说明书
3A7114DZH说明书QUANTM ™ 泄漏传感器用于检测 QUANTM 泵中的泄漏。
仅适合专业用途。
用于在普通场所使用的泵的套件用于在爆炸环境或危险（分类）场所使用的泵的套件重要安全说明请在使用或维修该设备之前，阅读本手册以及相关系统手册内所有的警告和说明内容。
妥善保存这些说明。
25F1081 个液位开关传感器 1 个减速器接头2 个弯头旋转接头（1/4 in. NPT ；3/8 in 软管端口）1 个三通接头1 根软管（长 30 in.，外径 3/8 in.）1 个换气阀25F1091 个液位开关传感器2 个弯头旋转接头（1/4 in. NPT ；3/8 in 软管端口）1 个三通接头1 根软管（长 30 in.，外径 3/8 in.）1 个换气阀（仅用于运输。
请丢弃。
）1 个弯头旋转接头（1/4 in. NPT ；1/4 in 软管端口）1 个弯头旋转接头（1/8 in. NPT ）1 根软管（长 20 in.，外径 1/4 in.）1个管路套管隔膜维修端口不得在爆炸性环境中打开。
爆炸性环境中使用的泵必须安装了 128658 插头或泄漏传感器套件25F109。
目录相关手册 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2警告 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3概览 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6组件识别 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6安装 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7准备泵 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7安装泄漏传感器 . . . . . . . . . . . . . . . . . . . . . . . . . .7安装软管和接头 . . . . . . . . . . . . . . . . . . . . . . . . . .9测试泄漏传感器 . . . . . . . . . . . . . . . . . . . . . . . . .12电气示意图 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13技术规格 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13美国加州第 65 号提案 . . . . . . . . . . . . . . . . . . . . . . . 13固瑞克标准保修 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14相关手册英文手册编号描述参考3A7637QUANTM 电动马达，修理零件马达手册3A8572QUANTM 泵，说明，工业型号泵手册3A9286QUANTM 泵，说明，卫生型号泵手册3A8946QUANTM 泵，零件，工业型号零件手册3A9287QUANTM 泵，零件，卫生型号零件手册23A7114D警告警告以下为针对本设备的设置、使用、接地、维护及修理的警告。
智能水漏检测传感器说明书
QUICK INSTALLATION GUIDEv1.0SMART WATER LEAKAGESENSORWARNINGS1. Install water leakage sensor at areas where it may leak.2. Don’t install water leakage sensor at position of rainwater, lampblack, water vapor, etc.3. Don’t install water leakage sensor at water immersed position.INTRODUCTIONSmart Water Leakage sensor adopts ZigBee wireless module. Super low power consumption circuit design ensures the long battery lifespan. Separate design of body and sensor efficiently prevents the influence resulted from high humidity. High precision and sensitivity applicable for basement, machine room, hotel, water tower , pool, swimming pool, solar , kitchen, bathroom and other places may have water leakage or water overflow.SPECIFICATIONWorking voltage: DC3V (2 x AAA battery)Static current: 5uA Alarm current: 35mA Networking: ZigBeeWireless networking distance: 70 (open area)Working temperature: -10°C~+50°C Working humidity: max 95%RHBody dimensions: 76 x 36.6 x 16.5 mm Sensor dimensions: 28.3 x 26.5 x 12.2 mmTRADEMARKS Zipato and the Zipato logo are registered Trademarks. All other product names mentioned herein may be trademarks or registered trademarks of their respective companies.NOTICEAlthough Zipato has attempted to ensure the accuracy of the content of this manual, it is possible that this document may contain technical inaccuracies, typographical, or other errors. Zipato assumes no liability for any error in this publication, and for damages, whether direct, indirect, incidental, and consequential or otherwise, that may result from such error , including, but not limited to loss of data or profits.Zipato provides this publication “as is” without warranty of any kind, either express or implied, including, but not limited to implied warranties of merchantability or fitness for a particular purpose. The published information in the manual is subject to change without notice.Zipato reserves the right to make changes in the product design, layout, and driver revisions without notification to its users. This version of the Installation guide supersedes all previous versions.Networking holeLEDWater leakage sensor body120 cm cableBracketINSTALLATION .INSTALLATION STEP 1:Remove battery insulation film to power it onBATTERY REPLACEMENTReplace the battery correctly, following the battery positive and negative electrode.Please pay attention to environmental protection and dispose used batteries properly.INSTALLATION STEP 3:Tear off the gummed film and stick the equipment in the required area.INSTALLATION STEP 4:Insert Water leakage body into the bracket.INSTALLATION STEP 2:1. DEVICE INCLUSIONAccoridng to application prompt, press the button for 2 seconds after the networking equipment, green flash, appplication interface prompted, networking success.2. DEVICE FACTORY RESET- Long press networking button while installing batteries - Device Reset Locally notification is Transmitted.- Please use this procedure only when the network primary controller is missing or otherwise inoperable.Equipment network anti-dismantling keyLIMITED PRODUCT WARRANTGENERAL TERMSNothing in this Limited Product Warranty affects your statutory rights as a consumer.The Limited Product Warranty set forth below is given by Tri plus grupa d.o.o. (Europe) (herein referred to as “ZIPATO”). This Limited Product Warranty is only effective upon presentation of the proof of purchase. Upon further request by ZIPATO, this warranty card has to be presented, too.EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, ZIPATO MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO. THEY DONOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOUHAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATOPRODUCT FROM. IN NO EVENT WILL ZIPATO BE LIABLE FORLOSS OF DATA OR FOR INDIRECT, SPECIAL, INCIDENTAL,CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OROTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT,OR OTHERWISE. HOWEVER, NOTHING IN THIS AGREEMENTLIMITS ZIPATO’S LIABILITY TO YOU (I) IN THE EVENT OF DEATHOR PERSONAL INJ URY TO THE EXTENT RESULTING FROMZIPATO’S NEGLIGENCE, OR (II) TO THE EXTENT RESULTINGFROM ANY FRAUDULENT MISREPRESENTATION ON THEPART OF ZIPATO, OR (III) TO THE EXTENT ARISING UNDERPART 1 OF THE CONSUMER PROTECTION ACT 1987 OF THEUNITED KINGDOM. SOME STATES OR COUNTRIES DO NOTALLOW: (1) A DISCLAIMER OF IMPLIED WARRANTIES; (2) ALIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTSOR THE EXCLUSION; OR (3) LIMITATION OF INCIDENTAL ORCONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS.IN SUCH STATES OR COUNTRIES, SOME EXCLUSIONS ORLIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLYTO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARYFROM STATE TO STATE OR FROM COUNTRY TO COUNTRY. YOUARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRYLAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.This Limited Product Warranty applies to ZIPATO brandedhardware products (collectively referred to as “ZIPATO HardwareProducts”) sold by ZIPATO (Europe), its European subsidiaries,affiliates, authorized resellers, or country distributors (collectivelyreferred to as “ZIPATO Resellers”) with this Limited ProductWarranty.The term “ZIPATO Hardware Product” is limited to thehardware components and all its internal componentsincluding firmware.The term “ZIPATO Hardware Product” DOES NOT include anysoftware applications or programs.G EOGRAPHICAL SCOPE OF THE LIMITEDPRODUCT WARRANTYThis Limited Product Warranty is applicable to HardwareProducts sold by Zipato Resellers in all countries listed at thebeginning of this document under the heading “Countries inwhich this ZIPATO Limited Product Warranty applies”. TheLimited Product Warranty will be honored in any country whereZIPATO or its authorized service providers offer warranty servicesubject to the terms and conditions set forth in this LimitedProduct Warranty. However, warranty service availability andresponse times may vary from country to country and may alsobe subject to registration requirements.LIMITATION OF PRODUCT WARRANTYZIPATO warrants that the products described below undernormal use are free from material defects in materials andworkmanship during the Limited Product Warranty Period setforth below (“Limited Product Warranty Period”), if the productis used and serviced in accordance with the user manual andother documentation provided to the purchaser at the time ofpurchase (or as amended from time to time).ZIPATO does not warrant that the products will operateuninterrupted or error-free or that all deficiencies, errors,defects or non-conformities will be corrected.This warranty shall not apply to problems resulting from:(a) unauthorized alterations or attachments; (b) negligence,abuse or misuse, including failure to operate the product inaccordance with specifications or interface requirements; (c)improper handling; (d) failure of goods or services not obtainedfrom ZIPATO or not subject to a then-effective ZIPATO warrantyor maintenance agreement; (e) improper use or storage; or(f) fire, water, acts of God or other catastrophic events. Thiswarranty shall also not apply to any particular product if anyZIPATO serial number has been removed or defaced in any way.ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS ASA RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONSFOR THE ZIPATO HARDWARE PRODUCT.LIMITED PRODUCT WARRANTY PERIODThe Limited Product Warranty Period starts on the date ofpurchase from ZIPATO. Your dated sales or delivery receipt,showing the date of purchase of the product, is your proofof the purchase date. You may be required to provide proofof purchase as a condition of receiving warranty service. Youare entitled to warranty service according to the terms andconditions of this document if a repair to your ZIPATO brandedhardware is required within the Limited Product WarrantyPeriod.[Other than in respect of products for domestic use (inparticular those listed in the first and last boxes in the tablebelow), this Limited Product Warranty extends only to theoriginal end user purchaser of this ZIPATO Hardware Productand is not transferable to anyone who obtains ownership ofthe ZIPATO Hardware Product from the original end-userpurchaser.P RODUCT WARRANTY PERIOD TABLEPRODUCT TYPE Smart Water Leakage SensorPRODUCT WARRANTY PERIOD One (1) yearIMPORTANTThe content of “Product Type” listed above is subject to change;please refer to the for latest update.P ERFORMANCE OF THE LIMITED PRODUCTWARRANTYIf a product defect occurs, ZIPATO’s sole obligation shall beto repair or replace any defective Zipato Hardware Productfree of charge provided it is returned to an Authorized ZIPATOService Centre during the Limited Warranty Period. Such repairor replacement will be rendered by ZIPATO at an AuthorizedZIPATO Service Centre. All component parts or hardware products that are replaced under this Limited Product Warranty become the property of ZIPATO. The replacement part or product takes on the remaining Limited Warranty Period of the replaced part or product. The replacement product need not be new or of an identical make, model or part; ZIPATO may in its discretion replace the defective product (or any part thereof) with any reconditioned equivalent (or superior) product in all material respects to the defective product.WARRANTORTri plus grupa d.o.o.Banjavciceva 1110 000 ZagrebCROATIATEL +385 (0)1 4004 404FAX +385 (0)1 4004 405DECLARATION OF CONFORMITY The manufacturer Tri plus grupa d.o.o declares under our soleresponsibility that the product:Marketing model: Smart Water Leakage SensorRegulatory model: hm-hs1wl-mTrade/Brand name: Zipatois in conformity with the Directive 2014/53/EU and carries the CEmarking accordingly.ETSI EN 300 220-1 V2.4.1 (2012-05)ETSI EN 300 220-2 V2.4.1 (2012-05)ETSI EN 301 489-1 V1.9.2 (2011-09)ETSI EN 301 489-3 V1.6.1 (2013-08)EN 62479: 2010EN 60950-1: 2006+A11:2009+A1:2010+A12:2011+A2:2013Changes or modifications not expressly approved by Tri plusgrupa d.o.o. for compliance could void the user’s authority tooperate the equipment.DISPOSING AND RECYCLING YOURPRODUCTWhen it reaches end of life, dispose of the product accordingto your local enviromental laws, guidelines and regulations.This symbol on the product or packaging means thataccording to local laws and regulations needs to be disposedof separately from household waste. Once this product hasreached the end of its life, please take it to a collection point(recycle facilites) designated by your local authorities, somewill accept your product for free or simply drop it off at yourZipato re-seller store. By recycling the product and itspackaging in this manner you help to conserve the environmentand protect human health. At Zipato, we understand and arecommitted to reducing any impact our operations and productsmay have on the environment. To minimize this impact Zipatodesigns and builds its products to be as environmentallyfriendly as possible, by using recyclable, low toxic materials inboth products and packaging.COPYRIGHT© 2017 Tri plus grupa d.o.o. All Rights Reserved.No part of this manual may be reproduced or transmitted in anyform without the expressed, written permission of Tri plus grupad.o.o.。
搜博 SM2130B-WT RS485 水浸传感器 说明书
SM2130B-WT RS485水浸传感器说明书概述SM2130-WT漏水控制器是一款成本低廉的智能化液体泄漏检测设备，其输出信号包含继电器信号和 485信号。
不需要外加转换模块就可以轻松的与各种监控系统相整合，实现远程报警及远程设备的控制。
SM2130-WT漏水控制器可监控长达 200米的双芯漏液传感电缆。
它既可以和检测线缆安装使用，也可以和它其检测探头配套使用，一旦检测到液体，控制器立即启动继电器，输出常开常闭无源信号，可与其它集成采集主机联网使用。
该产品采用标准的 modbus-RTU 通信，方便与监控系统集成。
适用于检测机房基站、仓库、图书馆、博物馆和工业现场等重要场所的实时泄漏检测，更加可用于空气处理装置、冷冻机组、液体容器、泵槽等需要监测泄漏的设备。
特点与特色1. 敏感度高2. RS485 远距离通信接口，最远可达 1.2 公里3. 指令简单4. 6-24V 宽电源供电5. 高性价比技术参数及特点使用说明1.接线直接使用设备自带的引线，根据颜色提示进行接线2.安装尺寸3. 通讯协议设备所有操作或回复命令都为16进制数据。
默认通讯波特率：9600,8,n,1。
基本命令格式：[设备地址][功能码][起始地址：2字节][数据长度：2字节][CRC16校验]意义如下：A、设备地址：设备地址范围为1-249,其中250即0xFA为通用查询地址，当不知道设备地址时，可用此通用查询地址进行查询。
B、功能码：不同的应用需求功能码不同，比如3为查询输入寄存器数据。
C、起始地址：查询或操作寄存器起始地址。
D、数据长度：读取的长度。
E、CRC校验：CRC16校验，低位在前，高位在后。
1）读取数据(功能码为0x03 )[设备地址][03][起始地址：2字节][数据长度：2字节][CRC16校验]设备响应：[设备地址][命令号][返回的字节个数][数据1][CRC16校验]响应数据意义如下：A、返回的字节个数：表示数据的字节个数，也就是数据1，2...n中的n的值。
A-LLM1漏水定位控制器使用说明书++
A-LLM1漏水定位控制器使用说明书Ver1.02010.11.21总说明请仔细阅读并妥善保管本说明书。
为确保正常工作，必须严格遵守本说明书。
A-LLM1漏水定位控制器可监控长达1500米的漏液传感电缆。
一旦检测到液体，A-LLM1漏水定位控制器即产生声光报警，数码管显示出泄漏位置，并启动继电器，产生本机无电压触点闭合，A-LLM1漏水定位控制器采用modbus RT U协议编程，方便与监控系统集成。
由于A-LLM1的成本低廉，使通过多个独立的传感器电缆小段来构建牢固的系统成为经济可行；对同类型传感电缆一次设定后，后续无需调整校准。
A-LLM1既可作为单独运行的泄漏检测报警单元使用，也可与其它集成采集主机联网使用。
适用于检测机房基站、仓库、图书馆、博物馆和工业现场等重要场所的实时泄漏检测。
·LED显示电源、泄漏、电缆故障及通信状态。
·数码管显示泄漏位置和电缆故障。
·能记录32条泄漏告警记录。
·实用可靠的双绞线串行RS-485通信试，最远通信距离可达1200米，标准的工业modbus 协议。
·12V直流电源供电，无极性接入。
·多种通讯波特率可选，通过软件设置模块地址和通讯波特率，无需使用开关。
·继电器输出形式常开常闭同时共存，可自由选择。
·良好的防静电、防雷、防浪涌技术，保证产品的可靠运行。
·方便的DIN导轨安装方式。
基本特点传感器兼容性A-LLW1000定位漏水感应线、TraceTek测漏传感电缆或者国产同类型测漏传感电缆传感电缆最大长度1500米精确度传感电缆长度的0.5%±0.5米环境额定值存储温度-40o C至60o C（0o F至140o F）工作温度-20o C至50o C（32o F至122o F）湿度5%到95%（无冷凝）电源要求A-LLM112V直流，3W串行接口网络配置RS-485双线网络，波特率可选，出厂默认为9600，可选地址为0到255，出厂默认地址0通讯协议MODBUS RTU继电器触点作用常态通电或常态断电，用户可自由选择；泄漏报警或泄漏与传感器故障报警额定值AC125V，0.5A，DC24V，1A。
雨量传感器产品说明书
雨量传感器产品说明书 雨量传感器产品说明书雨量传感器产品说明书目录第1章产品简介 (4)1.1产品概述 (4)1.2功能特点 (4)1.3产品优势 (4)1.4主要参数 (5)第2章硬件连接 (6)2.1设备安装前检查 (6)2.2产品外观尺寸和内部结构 (6)2.2.1外观尺寸 (6)2.2.2内部结构 (7)2.2.3接口说明 (8)2.2.4安装说明 (9)2.2.5注意事项 (10)第3章配置软件安装和使用 (10)3.1传感器接入电脑 (10)3.2传感器监控软件使用 (11)雨量传感器产品说明书 3.3修改波特率和设备地址 (12)第4章通信协议 (12)4.1通讯基本参数 (12)4.2数据帧格式定义 (12)4.3寄存器地址 (13)4.4通讯协议示例以及解释 (14)4.4.1读取设备地址0x01的当前累加雨量值 (14)4.4.2设备地址0x01雨量清除指令 (14)第5章售后 (15)5.1联系方式 (15)5.2质保与售后 (15)5.3免责声明 (16)雨量传感器产品说明书 第1章产品简介1.1产品概述ZZ-RS-ABSB系列雨量传感器，是一款能够自动观测并存储“雨量”参数的仪器，分为ABS材质和不锈钢材质两种。
我司研发的传感器外型小巧轻便，便于携带和组装，用于测量自然界降雨量，同时将降雨量转换为以开关量形式表示的数字信息量输出，以满足信息传输、处理、记录和显示等的需要。
广泛适用于气象台（站）、水文站、农林、国防、野外测报站等有关部门，可为防洪、供水调度、电站水库水情管理提供原始数据。
1.2功能特点ZZ-RS-ABSB系列传感器，具有功耗低、灵敏度高、安装便利、操作简单、使用方便等特点，可长期在野外观测并记录雨量数据；同时还具备24小时数据自动清零、手动清零、历史数据记录等功能。
1.3产品优势（1）成本低，实用性极强，可长期在野外使用。
（2）体积小，操作简单，性能可靠。
漏水系统漏水监测系统产品11页word文档
漏水检测系统产品一非定位漏液控制器 (2)应用领域 (2)产品特色 (2)技术参数 (2)面板说明 (3)检测方法 (3)常见故障 (3)声明 (4)二定位漏液控制器 (4)应用领域 (4)产品特色 (5)技术参数 (5)面板说明 (5)接线说明 (5)检测方法 (5)常见故障 (6)声明 (6)三无线漏水设备 (6)四 LCL-01漏水检测 (8)应用领域 (8)产品特色 (8)产品优势 (8)技术参数 (9)面板说明 (9)接线说明 (9)检测方法 (10)注意事项 (10)常见故障 (10)声明 (10)五点式漏水检测-终端 (10)产品简介 (10)产品特色 (10)应用领域 (11)接线方法： (11)一非定位漏液控制器非定位水浸变送器是有水，激励信号变化反馈给变送器，由变送器专用芯片对其进行放大、整形、比较、输出高一款配合水浸传感器使用的分体式导轨安装的新型变送器，主要用于监测现场某处或连续多处是否有积水险情，其原理是变送器调幅激励水浸传感器，一旦检测的水浸传感器所在位置某处低电平或继电器告警。
该系列产品使用电源，输入，输出三端隔离技术，极大程度提高电气兼容性和系统可靠性；输入的防氧化，防极化，防腐蚀设计；输出的光电隔离和线圈隔离保护，有效的保证产品的可靠性和寿命。
该系列产品通讯基站、精密机房、图书馆、宾馆、饭店、仓库等一些需要对有积水状况进行告警的场所。
应用领域专门针对数据机房、金融、证券、图书馆、仓库、实验室等重要场所的漏液监测而设计的，该控制器通过实时采集机房被保护区域中预先安装好的检测线缆的工作状态，及时准确报告机房中漏液位置，保证了被监测区域防泄漏安全。
产品特色隔离性高：电源，输入，输出三端隔离设计;四档灵敏度：可根据现场情况可调变送器灵敏度的档位;分体设计：变送器标准导轨式安装;传感器与变送器分体式设计;专利技术：传感器使用内置金属导体的导电橡胶线缆通过双绞连接方式固定在软线支架上设计;使用特点:水浸传感器需紧贴地面安装,无方向极性要求，防氧化，防极化，防腐蚀设计;适用场合广：根据现场检测范围大小可定制相应长度的水浸传感器;(最长 50 米)技术参数供电电压：DC 24V (9V~32V)工作温度：0℃~50℃工作湿度：20%RH ~100%RH误报率：＜100ppm静态功耗: 0.5W报警功耗最大：1.2W输出形式：继电器( 负载电流100mA)高低电平输出：VL 为0V（+0.5V）VH为 5V 或12V(±0.5V)灵敏度：档位1：0~5kΩ档位2：0~100kΩ档位3：0~1MΩ档位4：0~5MΩ（高灵敏档，遇极少水即可报警）带载能力：固态继电器≤100mA（大电流可以达到 1A，需定做）高低电平≥3k隔离强度：DC 2000V抗干扰等级：国标3级注：高电平输出12V时，供电电压应高于16V产品重量:变送器约 65面板说明标号1是接线端子，上图从里向外，分别是1-6根线的接头，1跟2是继电器的常开输出，3是RS485负，4是RS485正，5是电源输入正极（通常输入12V），6是电源输入负极。
485 型水浸传感器使用说明书
水浸传感器说明书 485型水浸传感器使用说明书水浸传感器说明书 第1章产品简介1.1产品概述水浸传感器主要用来检测是否出现漏水情况，本传感器采用交流阻抗测量方式，电极使用寿命长，不会出现氧化问题。
该水浸传感器广泛适用于通讯基站、宾馆、饭店、机房、图书馆、档案库、仓库、设备机柜以及其它需积水报警的场所。
1.2功能特点采用交流阻抗测量形式，交流阻抗方式可以有效避免电极发生氧化电解，极大的提高寿命。
漏水测量结果精准，误报率几乎为零。
1.3主要参数直流供电12V-24V DC开关量类型常开触点检测对象各类型水溶液耗电≤0.15W（@12V DC,25℃）开关量工作功率120VAC/24VDC水浸传感器说明书 1.4系统框架图本传感器可以连接单独使用，首先使用12V直流电源供电，设备可以直接连接带有485接口的PLC，可以通过485接口芯片连接单片机。
通过后文指定的modbus协议对单片机和PLC进行编程即可配合传感器使用。
同时使用USB转485即可与电脑连接，使用我公司提供的传感器配置工具进行配置和测试。
本产品也可以多个传感器组合在一条485总线使用，在进行485总线组合时请遵守“485总线现场接线守则”（见水浸传感器说明书 附录）。
理论上一条总线可以接16个以上的485传感器，如果需要接更多的485传感器，可以使用485中继器扩充更多的485设备，另一端接入带有485接口的PLC、通过485接口芯片连接单片机，或者使用USB转485即可与电脑连接，使用我公司提供的传感器配置工具进行配置和测试。
水浸传感器说明书 第2章硬件连接2.1设备安装前检查安装设备前请检查设备清单：名称数量高精度传感器1台12V防水电源1台（选配）USB转485设备1台（选配）保修卡/合格证1份2.2接口说明电源接口为宽电压电源输入12-24V均可。
485信号线接线时注意A/B两条线不能接反，总线上多台设备间地址不能冲突。
水浸传感器说明书线色说明电源棕色电源正（12-24VDC）黑色电源负通信黄色485-A蓝色485-B开关量白色开关量灰色开关量注意事项：请注意不要接错线序，错误的接线会导致设备烧毁。
Sensaphone-400漏水报警系统中文设置说明书
SENSAPHONE 400 中文用户手册SToneU Tech目 录1. 重要安全规程 (4)2. 介绍 (5)2.1. 指示灯 (5)3. 快速入门 (7)3.1. 键盘 (7)3.2. 准备工作 (7)4. 通信设置 (9)4.1. 语音消息 (9)4.1.1. ID录音 (9)4.1.2. 查询录音 (10)4.1.3. 输入端口录音 (10)4.1.4. 查询录音 (10)4.1.5. 删除录音 (11)4.2. 单元ID (11)4.2.1. 设置单元ID (11)4.2.2. 查询单元ID (12)4.3. 外拨电话号码 (12)4.3.1. 设置外拨电话号码 (12)4.3.2. 查询外拨电话号码 (13)4.3.3. 删除电话号码 (13)4.4. 语音或脉冲拨号 (14)4.5. 特殊拨号 (14)4.5.1. 使用暂停(PAUSE) (14)4.6. 响铃次数 (15)4.6.1. 设置响铃次数 (15)4.6.2. 查询响铃次数 (16)4.7. 收听时间 (16)4.7.1. 设置收听时间 (16)4.7.2. 查询收听时间 (17)4.8. 呼叫延迟 (17)4.8.1. 设置呼叫延迟 (17)4.8.2. 查询呼叫延迟 (18)4.9. 本地静音 (18)4.10. 语音重复 (18)4.10.1. 设置语音重复 (19)4.10.2. 查询语音重复 (19)4.11. 间隔时间(Inter Call) (19)4.11.1. 设置间隔时间 (19)4.11.2. 查询间隔时间 (20)4.12. 呼叫的最大值 (Max Call) (20)4.12.1. 设置最大呼叫 (21)4.12.2. 查询最大呼叫 (21)4.13. 时间 (21)4.13.1. 设置时间 (22)4.13.2. 查询时间 (22)4.14. 安全码 (22)4.14.1. 锁定键盘 (22)4.14.2. 解锁键盘 (23)5. 警报设置 (24)5.1. 输入设置 (24)5.1.1. 设置输入 (24)5.1.2. 检验输入配置 (25)5.2. 启动/禁止输入 (25)5.2.1. 变更输入的启动/禁止状态 (25)5.2.2. 查询输入的启动/禁止状态 (25)5.3. 输入辨识时间 (26)5.3.1. 设置输入辨识时间 (26)5.3.2. 查询输入辨识时间 (27)5.4. 设置高的和低的温度限度 (27)5.4.1. 设置指定输入的温度限度 (27)5.4.2. 启动/禁止温度高限/低限的响应 (28)5.4.3. 查询高的和低的温度限度 (28)5.5. 温度单位 (29)5.6. 温度校正 (29)5.6.1. 设置温度校正 (29)5.6.2. 查询温度校正 (30)5.7. 获得目前温度 (30)5.8. 启动/禁止 AC (31)5.8.1. 启动/禁止 AC警报 (31)停电辨识时间 (31)5.9. AC5.9.1. 设置停电辨识时间 (31)5.9.2. 查询停电辨识时间 (32)5.10. 噪音警报监听 (32)5.10.1. 设置噪音警报灵敏度 (32)5.10.2. 查询噪音警报的灵敏度 (33)5.10.3. 设置噪音警报辨识时间 (33)5.11. 启动/禁止噪音报警 (34)5.11.1. 变更启动/禁止噪音警报 (34)5.12. 离场延迟 (34)6. 确认、状态报告与远程访问 (35)6.1. 警报确认 (35)6.1.1. 现场确认 (35)6.1.2. 电话确认(音频) (35)6.1.3. 回拨确认 (35)6.2. 状态报告 (36)6.2.1. 例子: 状态报告，没有警报 (36)6.2.2. 例子: 状态报告，已存在警报 (36)6.2.3. 例子: 状态报告，禁止的输入 (37)6.2.4. 电池状态 (37)7. 操作 (38)7.1. 警报的检测、外拨和确认 (38)7.2. 外拨电话例子 (38)8. 连接输出 (39)8.1. 自动模式 (39)8.2. 设备输出模式 (39)8.3. 查询输出模式 (40)8.4. 本地切换输出 (40)9. 巡查SENSAPHONE系统 (41)1.重要安全规程SENSAPHONE 400单元能够提供安全、可靠的性能。
Panasonic EX-FC1 简易电线节省漏水检测传感器指南说明书
Thank you very much for purchasing Panasonic products.Please read this Instruction Manual carefully and thoroughly for the correctand optimum use of this product.Kindly keep this manual in a convenient place for quick reference.OUTLINE●This is the simple wire-saving unit which can be connected with max. 8leak detection sensors (NPN output type).●Even if only one leak detection sensor (NPN output type)is connected tothis product, the output is gained when leak is detected or the sensor ismounted improperly.●Since the exclusive snap male connector (SL-CP1) is used for connec-tion, wire-saving can be easily made.MOUNTING●In case of using screws•Mount using M4 pan head screwswith a tightening torque of 0.8N·mor less. However, in case of sidemounting, make sure to mount theunit such that the unit stopper facesfront.Mounting position 1●Two installation positions are available for the unit mounting base so thatthe unit direction can be changed. Install the base at one of them.Mounting position 2●In case of using a DIN rail or themounting bracket (MS-DIN-3)(optional).1.Fit the rear part of the unit mount-ing base on a 35mm width DIN railor the mounting bracket (MS-DIN-3)(optional).2.Press down the front part of theunit mounting base on the 35mmwidth DIN rail and fit the front partof the base on the DIN rail.*For removal, insert a flatheadscrewdriver into the DIN rail stop-per and pull towards yourself.●When mounting the unit, be sure to use the unit mounting base(MS-SL-2) (accessory).●When installing the unit mounting base to the unit, insert the basealigned with the grooves of the unit and move until the unit stopper islocked.1.Insert aligned with the2.Make the unit stopperI/O CIRCUIT DIAGRAM (for 1 channel)Note: Since the output does not incorporate a short-circuit protection circuit, make sure to usethis product within the specification and take care against wrong wiring.PART DESCRIPTION2143●This product has been developed / produced for industrial use only. ● T his product is suitable for indoor use only.●Avoid using the product in an explosive atmosphere because this prod-uct does not have an explosive-proof protective construction. ●Make sure that the power supply is off while wiring. ●Take care that wrong wiring will damage the product.●Verify that the supply voltage variation is within the rating. Take care that if a voltage exceeding the rated range or an AC power supply is directly applied, the sensor may get damaged or burnt.●If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.●In case noise generating equipment (switching regulator, inverter mo-tor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.●Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to in-duction.●Do not use during the initial transient time (approx. 0.5 sec.) after the power supply is switched on.●Cable extension is possible up to total 10m with 0.3mm 2, or more, cable. However, in order to reduce noise, make the wiring as short as possible.●Make sure that stress by forcible bend or pulling is not applied to the cable joint.●Since the output does not incorporate a short-circuit protection circuit, make sure to use this product within the specification and take care against wrong wiring.●In case a surge is generated in the used power supply, connect a surge absorber to the supply and absorb the surge.●Make sure to use an isolation transformer for the DC power supply. If an auto-transformer (single winding transformer) is used, this product or the power supply may get damaged. ●Avoid dust, dirt, and steam.●Take care that the product does not come in contact with oil, grease or organic solvents, such as, thinner, etc., strong acid or alkaline. ●This sensor is suitable for indoor use only.CAUTIONSSPECIFICATIONSDesignation Simple wire-saving unit for leak detection sensor(NPN output type)Model No.EX-FC1Connectable sensor NPN output type leak detection sensor (EX-F71, EX-F72,EX-F61, EX-F62) (Note 1) (Note 2)Applicable connector SL-CP1Supply voltage 12 to 24V DC± 10 % Ripple P-P 10% or lessCurrent consumption50mA or less (for one unit)135mA or less (including the sensor input current when all outputs are ON)OutputRelay contact 1a• Switching capacity: 30V 1A DC (resistant load)• Min. applied load: 10mV 10μA DC• Electrical lifetime: 100,000 times or more(rated load, switching frequency 20 times/min.)• Mechanical lifetime: 50,000,000 times or more(switching frequency 180 times/min.)Output operation The output relay is ON when the input signal from the sensor is ON.Response time 5ms or less (excluding the response time of the sensor)Input points8 pointsAmbient temperature -10 to +60ºC (No dew condensation or icing allowed)Storage: -20 to +70ºCAmbient humidity 35 to 85% RH, Storage: 35 to 85% RH Material Enclosure: ABS, Terminal part: PBT Cable 0.2mm 2 4-core cabtyre cable, 2m longWeight Approx. 85gAccessorySL-CP1 (Snap male connector): 8 pcs.MS-SL-2 (Unit mounting base): 1 pc.Notes: 1) PNP output type sensor (including leak detection sensor) cannot be connected.101012) Ordinary sensor (NPN output type) or no-voltage contact output sensor can beconnected.INTENDED PRODUCTS FOR CE MARKING●The models listed under “SPECIFICATIONS ” come with CE Marking.As for all other models, please contact our office. ●Contact for CEPanasonic Marketing Europe GmbH Panasonic Testing Center Winsbergring 15, 22525 Hamburg,GermanyConnection method1. By holding the SL-CP1 with the cable connected, insert it into the connector of the EX-FC1 reliably till it stops.Note: Do not pull out by holding the cable, as thiscan result in cable disconnection.Disconnection method2. By holding SL-CP1, pull it from the EX-FC1 horizontally.CONNECTION SETTING SWITCH6The connection setting should be carried out in the power supply off condi-tion after removing any electrostatic charge which may be present on your body.●Operation matrix for each indicatorOperationConnection state of theleak detec-tion sensor State of theconnectionsettingswitchLeakdetectedconditionNormalindicator (Green)Error indicator (Red)Output indicator (Orange)Normal Connected ONNot leakedLights up Turns off Lights up LeakedTurns off Lights up Turns off Unconnected OFF -Turns off Turns off Lights up ErrorConnected OFF Not leaked Lights up Lights up Turns off UnconnectedON -Turns offLights upTurns off●For the channel that the unit sensor is connected to and the connection setting switch is set to “ON” side, the error indicator (red) lights up for a moment when the power is turned on. This is not a malfunction for the unit because it is caused by characteristic of the sensor.●Make sure to set the connection setting switch with the connector No. to which the leak detection sensor is connected, to “ON” side.●In case both the normal indicator (green) and the error indicator (red) light up, the connection setting switch with the connector No. to which the leak detection sensor is connected, is not set to “ON” side. Set the connection setting switch with the connector No. to which the leak detec-tion sensor is connected, to “ON” side.●In case the error indicator (red) lights up, the leak detection sensor de-tects leak or the connection setting switch is set to “ON” side without connecting the leak detection sensor. If the connection setting switch is set to “ON” side without connecting the leak detection sensor, set the connection setting switch to “OFF” side.●If the leak detection sensor detects leak or the connection setting switch is set to “OFF” side in the state that the leak detection sensor is improp-erly mounted to the mounting bracket, the sensor judges as the output is ON. Be careful when setting.NOT USED76543210ONThese are not used.“ON” side “ON” side “ON” side“ON” sideConnection setting switch setting exampleIn case the input of 0, 3, 4 and 5 are set to effective.https:///id/pidsx/globalOverseas Sales Division (Head Office)2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-568-33-7861 FAX: +81-568-33-8591For sales network, please visit our website.PRINTED IN JAPAN © Panasonic Industrial Devices SUNX Co., Ltd. 2018。
海尔盒式式相干式厨具漏水、漏气、水位等传感器电缆wick Number码：00102364说明书
29
30
8ga Brown/Tan 12.583 HIGH WATER PUMP (+)
31
8ga Yellow
14.333 HIGH WATER PUMP (-)
32
16ga Brown/Red 16.917 HIGH WATER ALARM INDICATOR (+)
33
16ga Yellow/Brown 16.917 HIGH WATER PUMP RELAY (FROM SW)
8
16ga Yellow
11.083 WASTE SENSOR (-)
9
16ga Pink/Gray
14.167 WASTE SENSOR (S)
10
16ga Blue/White 15.917 COURTESY LIGHT, FWD (+)
11
16ga Yellow
13.5 COURTESY LIGHT, FWD (-)
6.0833 PARALLEL SOLENOID (-)
26
12ga Brown/Org
7.75 MAIN BILGE PUMP (AUTO)
27
12ga Brown/Red 8.5833 MAIN BILGE PUMP (MANUAL), TO SW
28
16ga Red/White 7.8333 START BATTERY TEST (+)
151 172 203 203 126
155 209 180 260 163
41 HULL HARNESS WIRE LIST
WIRE# GAUGE COLOR
41
16ga Blue/White
规格书漏水位置检测器
TS-KS-W1911-1 公司规格书漏水位置检测器AD-AS-1LDM年月拓自达电线株式会社电子事业本部系统・光学电子事业部<<<为了安全地使用!!>>>如无视注意标签或下述警告事项而进行错误使用，除了可能会造成死亡或重伤，还能产生火灾、触电和故障。
□绝对不要进行检测器的分解或改造。
□负责使用以外的人员请不要进行施工以及定期检查点检。
□请不要用湿手接触检测器内部。
□维护时请避免使用有机溶剂，请用纱布等柔软的废棉纱头轻轻进行干擦拭。
□请在安装检测器前确认设备的额定电压和电源电压。
□施工以及接线，请按照本使用说明書指示的方法进行。
□保养和定期检查，请按照本使用说明書指示的方法进行。
□使用控制输出接点时，请按下述检测器规格表确认接点的额定负荷。
请勿放置□一般易被人接触的地方。
□有振动、有机气体的地方，和强电磁感应发生源附近。
□灰尘多的地方。
□被水浸湿的地方，高温多湿的地方。
保修本检测器在出厂已经过严密的质量管理和检査。
如万一发生由于制造上的不完备而导致的自然故障时，将按下述规定予以修理或更换。
保修规定1. 无偿保修期（商购买后1年内）在按照使用说明书进行正常使用的条件下，在保修期内发生故障时，将予以无偿修理或更换。
烦请和对应窗口联系。
2. 保修适用除外①超过保修期。
②由于使用上的错误，以及不当的修理或改造造成的故障。
③购买后，由于移动、跌落等造成的故障，或者损伤。
④火灾以及天灾造成的故障，或者损伤。
⑤故障的原因为本制品原因以外的场合。
⑥出差修理費用（出差费，技术费）。
目录页1. 适用范围 12. 漏水位置检测系统的结构 13. 规格 2 ~ 33-1 额定值3-2 性能3-3 控制输出接点规格4. 动作图 3 ~ 4 4-1 标准动作图4-2 警报保持设定时的动作图5. 安装 56. 漏水传感器（AD-LS 传感器） 5◇附图-1漏水位置检测器（AD-AS-1LDM）外形尺寸图◇附图-2漏水位置检测器（AD-AS-1LDM）各部分的说明◇附图-3漏水位置检测器（AD-AS-1LDM）动作设定开关的说明◇附图-4漏水位置检测器（AD-AS-1LDM）显示部分的说明-1◇附图-5漏水位置检测器（AD-AS-1LDM）显示部分的说明-21.适用范围本规格书适用于以防机房、重要设备、仓库以及贵重资料等手漏水侵害而开发的漏水位置检测器（AD-AS-1LDM ）。
可移动漏水报警器使用说明
移动式漏水报警器使用说明书北京天隆达科技有限公司功能描述：将报警线放置在需要监控的地方，连接该设备，监控漏水情况，一旦有水侵过报警线，报警器将通过GSM调制解调器将报警信息发送到指定的手机上，当报警消失，报警器将报警清除信息同样发送的用户手机上。
适用范围：适用电站、矿山、工程现场、隧道施工等无人看守或人际罕置的现场。
使用条件：✓有gsm网覆盖地区。
✓使用220V电源提供电源。
✓使用者使用gsm手机接收报警信号。
报警时时刻使用设需要开机状态。
设备组成：1.移动式漏水报警器主机一台2.12v直流稳压电源一台3.GSM调整解调器一台4.GSM天线一部5.GSM转换连接线一个6.10米信号线一条7.232下载线一条8.10米传感电缆一条9.使用说明书一本10.设置软件光盘一个11.包装箱一个操作过程：1.下载数据：使用计算机串口下载使用者的电话号码，信息抬头，汇报时间，校正时间，校正日期，详细见下载说明。
该功能在使用前设置一次即可，除非修改信息，不必重新下载。
2.手动修改数据：如有数据修改可以·直接使用操作键盘进行修改，详细说明见设置说明。
3.调制解调器安装好号码卡。
4.连接好GSM调制解调器，五芯电缆的一头连接GSM调制解调器，另一头连接设备的信号插座的五芯座。
5.连接传感线，连接完成后，开电，按复位键。
绿色灯亮显示报警器正常工作。
如红灯常亮表明有报警信号，按复位键将消除报警信号。
6.当出现稳定的报警信号后，设备将于5秒后将信号发出，并且将发送的电话号码和报警信息显示在显示屏上（139××××××××dail），蜂鸣器并发出响声，以提示报警。
如发送成功显示（139×××××××OK）发送失败显示（139×××××××ERROR）。
WD水感应传感器胶带安装和操作指南（Dwyer仪器公司）说明书
The small and discreet Model WD Water Detector is designed for dependabledetection of low levels of conductive liquids. The module features a sturdy and reli-able aluminum enclosure and is powered by 24 VAC or 24 to 30 VDC. Water sens-ing tape attaches to module and if any liquid comes in contact with the tape theresistance is changed and the alarm will be triggered. The tape is hydrophobic so itdoes not absorb any of the liquid it is detecting which makes for a faster drying timeand faster return to service after a water leak.The sensing tape is 1˝ wide and can be bought in lengths of 5, 10, 15 and 25 feet.Multiple tapes can be connected together to extend the coverage area which makesit ideal for domestic as well as commercial applications. Typical uses include com-puter rooms, telecommunication facilities, in drip pans under HVAC equipment andaround water pumps.INSTALLATIONRemove front panel of device. Run wires through back plate and make terminations.Reassemble front panel. Plug the tape into the module and fasten the mountingscrews. Use included plastic clips to mount tape to clean and dry surface. Contactcement provides a more secure installation than double face tape. Fold tape on it-self to make sharp corners. Insulate tape from conduits and ground wires. Ground-ed tape may cause detector failure.OPERATION AND TROUBLESHOOTINGGreen LED will indicate proper power. Red LED is an alarm indicator. The water de-tector will go to alarm contact state on loss of power or if the tape sensor is removed.An open or shorted tape will be sensed by the detector and will produce an alarmcontact state as well. The “Test” button can be used to test module operation. De-pressing the button will simulate water detection on the tape and produce an alarmcontact state. It is important to dry sensing cable with paper towel in case alarm hasbeen caused by water. Do not allow water to evaporate on its own. Conductiveresidue will be left behind which will change tape’s resistance. In worst case falsealarms may occur over time.If alarm is present and water cannot be located:1.Disconnect tape2.Unplug end of line (EOL) resistor from end of tape3.Plug EOL resistor into the moduleIf alarm clears then replace the tape.If alarm persists then replace the module.WIRINGModel WD Water Detector is provided with round opening for 1/2˝ conduit or flexconnector. Terminations are made to screw terminal connectors shown in Figure 1.Both outputs of alarm relay function identically. Contacts could be connected in par-*********************************************************************outputs.SPECIFICATIONSService: Conductive Liquid.Switch Type: DPDT.Electrical Rating: 1A @ 24 VAC/VDC.Power Requirements: 24 VAC, 24 to 30 VDC.Power Consumption: 35 mA maximum.Electrical Connections: Screw terminals.Conduit Connections: Hole for 1/2˝ conduit.Enclosure: Extruded aluminum.Sensor Tape: 1˝ (25.4 mm) wide and 5, 10, 15 or 25 feet long.Weight: 8 oz (.23 kg).CONNECTION[2.10]。
深圳市云迪尔科技有限公司 YDL-LD02 定位漏水控制器 说明书
YDL-LD02定位漏水控制器说明书一、产品简介我司YDL-LD02定位器是一款不带显示的、通过RS485通讯方式实时获取当前漏液状态的定位漏水控制器，可定位到漏水感应线的漏水位置，输出数据的单位为m，最小分辨率为0.1m，精度为：感应电缆长度0.5%FS ±0.5米。
YDL-LD02内含一路定位漏水绳状态采集电路，两路线缆断裂检测电路，一路RS485输出电路及两路路继电器常开输出电路；同时包含两个LED状态指示灯及一路复位按钮，内置一个蜂鸣声音告警器。
YDL-LD02广泛应用于机房、厂房车间、图书档案管理、实验室以及其他需要漏液检测的地方。
二、产品特点1、工作电压：DC12V2、输出方式：RS485标准输出；两路继电器常开输出；3、传输速率：300-115200bps；4、通信协议：MODBUS RTU；5、工作环境：-20℃至70℃相对湿度为5%至95%；6、工作精度：一路不定位漏水绳状态采集，灵敏度可调，可测量0-3000m；7、状态指示：两个led指示灯及一路复位按钮；三、主要技术参数四、拨码开关真值表五、系统调试备注：调试工具未随设备发出，请联系我司相关人员免费索取。
首先将设备通过串口转RS485转换器正确地连接到PC电脑，然后打开调试工具。
1、调试工具界面备注：（1）感应线缆的长度可以设置为0或者当前线缆的实际长度：当感应线缆长度设置为0时（出厂默认值为0），设备工作在工作模式一（普通算法模式，即出厂默认模式）；当感应线缆长度设置为当前线缆的实际长度时，设备工作在工作模式二（增强算法模式）：此模式下设备会根据当前线缆长度自动校准优化泄露位置值；并且此时需要调整S+和L+的接线：S+接第一组感应线缆的回环线（对应标配引出线为绿色），L+接第一组感应线缆的感应线（对应标配引出线为红色）。
（2）工作模式一（普通算法模式，即出厂默认模式）适合较小区域（铺设的线缆较少）并且铺设感应线缆所经过的区域没有干扰信号的环境下使用；工作模式二（增强算法模式）适合较大区域（铺设的线缆较多）或者铺设感应线缆所经过的区域存在较强干扰信号的环境下使用。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
应用范围
适用于机房、空调房等场所的漏水检测。
主要技术参数
型号
供电电源AC24V±10%
组成电极片（或感应绳）、信号变换器
感应绳长度可以定制
输出形式正常输出短路，灯为绿色，闪烁
告警输出开路，灯为红色，闪烁，蜂鸣器报警。
连接端子5PIN 5.08间距插拔端子
其他指标报警输入电阻<200千欧
静态电流< 20 mA
告警电流< 30 mA 如需要接大电流的告警负载，请外接一DC12V 1A继电器.
电导率>5us.cm-1
隔离度>2000V
误报率0
工作环境-40～85℃，10-95%RH
信号变换器外壳阻燃工程塑料
重量约100g
外形结构
适配器+电极片适配器+漏水感应线
图 1
信号变换器接线图
图 2
一、 1、2接线端为电源输入，1为正，2为负。
4、5接线端为继电器输出，漏水告警时继电器输出短路，同时灯变为红色，蜂鸣器报警。
6、7接线端外接漏水感应绳。
漏水感应绳接入时没有方向性，可以增加延长线。
二、 4位拨码开关用于设置，前三位设置感应漏水灵敏度，第四位设置蜂鸣器报警功能。
其具
体功能如下：
拨码１：最灵敏档，开关接通时，感应绳接触水面即报警；
拨码２、3：感应水面深度及灵敏度相对拨码1依次下降。
拨码4：开关接通时，报警时蜂鸣器响，否则蜂鸣器不工作。
安装方式
图 3
传感器感应绳安装在容易产生漏水的地方。
把信号变换器安装在感应绳附近，用两芯线连接感应绳和信号变换器。
信号变换器用DIN35MM 标准导轨槽安装。
连接好电源和输出线后，一加电信号变换器处于正常检测漏水的工作状态，灯为绿色，闪烁，输出为开路；当有漏水发生时，产生告警，灯由绿色变化为红色，闪烁，输出为短路，蜂鸣器报警；漏水消失后，告警恢复为正常的工作状态，灯由红色变化为绿色，闪烁，输出为开路；
注意事项
一般情况下请勿打开传感器上盖，打开后再装配时上盖标贴电源输入一端一定要与下盖（如图3右端）对应，不能装反。
传感器应该安装在最能代表被测环境状态的地方，避免安装在位置比较高的死角、或者远离空调、水管接头的场所。
36.5cm 87
87cm 电源输入端
GREEN
RUN R E D ALARM。