模具英语
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具英语
替换镶件：Interchangeable Mold Inserts。
模芯：Parting Core。
侧抽芯：Side Action 。
脱螺纹：unscrew。
excluding metallic parts price：不包括五金件价格。
Subtract to button up, convenient mold：反向弹出：reverse eject，硬度：hardness 。
牛角进胶：cashew gate 。
runner system：浇道系统。
stress crack：应力电裂。
orientation：定向。
sprue gate；射料浇口。
直浇口：nozzle射嘴。
slag well：冷料井。
bronze：青铜。
brass；黄铜。
prototype mold；手办模。
side gate：侧浇口。
edge gate：侧缘浇口。
tab gate：搭接浇口。
film gate：薄膜浇口。
flash gate：闸门浇口。
slit gate：缝隙浇口。
fan gate：扇形浇口。
dish gate：因盘形浇口。
Mold working automatic 模具自动生产 overmolding 包胶模H=F=1/2t~1/5t 。
T=2.5~3.5mm 。
diaphragm gate：隔膜浇口。
ring gate：环形浇口。
Sub gate：潜入式浇口。
tunnel gate：隧道式浇口 pin gate：针点浇口。
晒纹Texturing。
方铁;Spacer Block . 顶针板:Ejector Plate。
There are under cut at this area of part 零件这处有倒扣，can not be released 不能脱模 runner shut off 转水口cavity and core direct cut on A.B-plate 料位在A,B板上原身出。
2 stage ejection 二次顶出interchangeable cavity,core and sliders for each part互换前后模和行位生产每一个产品。
模具英语词汇大全
汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Casti ng die=W 造模Part=ffi 件Die material=制模材料Tool desig门=模具设计Strip desig门=料条设计Tool desig n approval^ 具设计审核Tool desig n modificatio n/revisio n=模具设计更改Tool parts design （detail） = 模具钣件设计（详细）FMC Make=保丽龙制作modification= 更改Check & measured查& 测试Machining= 机器加工Large m a c h i n i n g =在大型机器上加工上下模架（铣、车等）Small machi ning二在小型机器上加工模块等Assembly 二组立NC Machining=NC 雕刻加工Fitti ng=研磨组立Spott ing二合模Dowel pi n=定位销Assemble gas spri ng安装氮气缸Adjustme nt=调试Lower trim steels=下刃块Sectio门=冲头断面Trim pun ch=切刃冲头jack screw hole=起重［千斤顶］螺旋孑L Die set, lower plate=T 模架Die set, upper plate=h 模架Ball beari ng guide posts and bush in §$=球形滚珠导柱和轴套Cage=®Rigidity= 强度Thi n=薄Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, internally heel form & trim sections^箱根的模架，成形与切刃冲头带导引Con structio n method^ 构方法Lower die trim in serts=下模切刃块Lower trim in serts retai ner=T 模切刃块承盘Assemble in serts=fi 立镶块Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=# 条窗户镶块Die tryout=试模Cushi ng stroked 冲行程Guide lift pin= 导引升降销Stamp partsh 中钣件Run off parts=中钣件Hit parts=冲钣件Lifters=提升器Coil=卷材Guide block 二导弓I块Guide the coil through the tool=# 引卷材layout in spectio n=全尺寸检验Die in specti on & approval=模具检查和审核delivery=发货Rejected* 收Scrapped=报废Rework=返工stop block=停止块Hydro form液压成形Shear=K 切Sen sor=ft 感器Stretch web=S 伸网Layout the parts=S 计钣件Preced ing into the desig n继续设计Guide the coil through the tool=# 弓I卷材Check ing aid /check ing gage=检具Jig=夹具Fixture=夹具Ball beari ng guide posts and bush in gs= 球形滚珠轴套Guide post=导柱Bushings二导套Using material thickness radii where sharp corners are shown on the part reduces the occurre nee of chipped punch or die corners in the tool.=在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, intern ally heel form & trim sectio ns=带箱根的模架，成形与切刃冲头带导引Gra nite Tabled 岗岩平台Plotter=.描绘器,图形显示器,绘图器,坐标自记器，标图员Belt San der=# 磨机Metal Cutti ng Ba nd Saw^ 式带锯床Bla nchard Grin der=大型平面磨床Stretch carriers=S 伸运送装置Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=M 条窗户镶块Heel plates=W 托Prepare for delivery^® 备发货Key=键For locati ng reta iner blocks^ 盘键For holdi ng butt ons or pilots=冲母座或导销键For fixed heel or positive stop=B 根键Con structio n method=S 构方法Manual Surface Grin der=手动平面磨床Spott ing red=合模用丹红Layout ink=试模用蓝墨水Masking tape=M色不透明胶带(遮蔽胶带) Pliers=尖嘴钳，老虎钳Crese nt wren ch=可调扳手Pump pipe=泵管CMM=三次元测量仪Symmetric=对称的The axis of symmetry^ 称轴Tech nical^ 术上的Diago nal=对角线One two three block” 二三模块Adjustable parallels^ 调平行块Stop block=阻止块Backi ng Plate=背板Shoulder Bolt=肩头螺丝(Stripper bolt)Keeper Block=行程块Corner Guide Block=# 块Dowel pi n=定位销Joe Blocks=ft 密量块Whirly Gig=筒夹式冲子成形器Chamfer Tools= 到角刀具组Angle Plate=L形直角座Gage Pins=^寸塞规Si ne Plate (mag netic)=E 弦磁台Flute End Mill=硬质合金钢铣刀Mill Cutter=波纹粗铣刀(标准型) C' bore/ counter bore六角沉头铣刀Radius Dresser=^ 轮修整器Boring Head & Boring Bar=搪孔器、搪刀杆Pin二销Reamer=绞刀Approval 确认Impact wren ch二气动扳手Air pi n=空气销bumper[‘ bQmpE(rn.缓冲器Ven dor [ ‘ ven dE(r)d C:(r)] n.卖主stripper layout=排样图drawing of panel #987415&16=钣件设计图(公差)Arbor =柄轴；心轴Drill chuck=钻夹头Butt on=冲母座Nitroge n Cyli nder=氮气缸Pilot=导销Retai ner二承盘Butt on=冲母座Hose Straps嗽管夹(塑料)Set Screw=S 塞Jig & fixture =夹具Checking fixture二检具Guide Block 二导块Plu nger二柱塞Pierce=?中孑LWear Strip=W 磨板Mating area=ffl立的接触面Accommodate 二适应Wiping hard (very shiny)=过分摩擦闭合[接触](闪光)In crease the die cleara nee betwee n the form steels=®加成形块间隙Cleara nce= 间隙Oil paper 二油纸0-11” Micrometer=0-11 ”千分尺Trim line=切边+/-0.5mm uni ess otherwise specified除非另有规定，否则公差为+/-0.5mmPart tolera nce=R件公差Ball no se=球刀Bore二镗Line tap=攻丝校直Borer二镗刀，镗床Chamfer二倒角Radius=半径Coola nt=切削液Pun ch=^冲头Distribution Blocks=接头座Screw二螺丝Shop# 间Flat Feet Keepers顶料销Ejector Pin=顶出销Spring二弹簧Straight Port Adapter=直管接头Y-205 Hose=< 管(塑料)Short Neck Adapter=S 接头45 Swivel= 45 接头(adjustable) 45。
汽车模具英语
精品文档汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”Tool design approval=模具设计审核Tool design modification/revision=模具设计更改Tool parts design (detail) = 模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引FMC Make=保丽龙制作Construction method=结构方法modification= 更改Check & measure=检查& 测试Machining= 机器加工Large machining=在大型机器上加工上下模架（铣、车等）Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块Punch stripping plates=冲头压料板Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程Dowel pin=定位销Guide lift pin=导引升降销Assemble gas spring=安装氮气缸Stamp parts=冲钣件Adjustment=调试Run off parts=冲钣件Lower trim steels=下刃块Hit parts=冲钣件Section=冲头断面Lifters=提升器Trim punch=切刃冲头Coil=卷材jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块Die set, lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验精品文档Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托stop block=停止块Prepare for delivery=准备发货Hydro form 液压成形Key=键Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或导销键Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红Checking aid /checking gage=检具Layout ink=试模用蓝墨水Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳Ball bearing guide posts and bushings=球形滚珠轴套Cresent wrench=可调扳手Guide post=导柱Bushings=导套Pump pipe=泵管Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块Granite Table=花岗岩平台Backing Plate=背板Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销精品文档Joe Blocks=精密量块Set Screw=螺塞Whirly Gig=筒夹式冲子成形器Jig & fixture =夹具Chamfer Tools=倒角刀具组Checking fixture=检具Angle Plate=L形直角座Guide Block=导块Gage Pins=英寸塞规Plunger=柱塞Sine Plate (magnetic)=正弦磁台Pierce=冲孔Flute End Mill=硬质合金钢铣刀Wear Strip=耐磨板Mill Cutter=波纹粗铣刀（标准型）Mating area=组立的接触面C’bore/ counter bore=六角沉头铣刀Accommodate=适应Radius Dresser=砂轮修整器Wiping hard (very shiny)= 过分摩擦闭合[接触]（闪光）Boring Head & Boring Bar=搪孔器、搪刀杆Pin=销Increase the die clearance between the form steels=增加成形块间隙Reamer=绞刀Clearance=间隙Approval=确认Oil paper=油纸Impact wrench=气动扳手0-11” Micrometer=0-11”千分尺Air pin=空气销Trim line=切边bumper[‘bQmpE(r)] n.缓冲器+/-0.5mm unless otherwise specified 除非另有规定，否则公差为+/-0.5mmVendor [‘vendE(r), -dC:(r)] n.卖主Part tolerance=钣件公差stripper layout=排样图Ball nose=球刀drawing of panel #987415&16=钣件设计图（公差）Bore=镗Line tap=攻丝校直Arbor =柄轴；心轴Borer=镗刀，镗床Drill chuck=钻夹头Chamfer=倒角Button=冲母座Radius=半径Nitrogen Cylinder=氮气缸Coolant=切削液Pilot=导销Punch=冲头Retainer=承盘Distribution Blocks=接头座Button=冲母座Screw=螺丝Hose Straps=软管夹（塑料）Shop=车间精品文档Flat Feet Keepers=顶料销Crib=仓库Ejector Pin=顶出销CNC mill= CNC机床Spring=弹簧Jack=千斤顶Straight Port Adapter=直管接头Strips=料条Y-205 Hose=软管（塑料）Styrofoam [`stairEfEum]n.聚苯乙烯泡沫塑料（保丽龙材料）Short Neck Adapter=短接头Cut off=落料45。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具英语词汇大全
模具英语词汇表Aabrasive grinding 强力磨削L 3 a b r a s i v e[☜'breisiv] a.磨料的, 研磨的L2,3 absence ['✌bs☜ns] n.. 不在，缺席L17 accesssory[✌k'ses☜ri] n.附件L10 accommodate[☜'k m☜deit] v. 适应L 5 accordingly[☜'k :di☠li] adv.因此,从而,相应地L7,1 3 accuracy['✌kjur☜si] n精度,准确性L1, 3 a c t u a t e['✌k t j u e i t] vt.开动(机器), 驱动L8 adequate['✌dikwit] a. 足够的L1 3 adhesive[☜d'hi:siv] n. 粘合剂L2 2 adjacent[☜'d✞eisnt] a. 邻近的L1 3 adopt[☜'d pt] vt. 采用L 4 advance [☜d'v✌:ns] n.进步L7 advisable [☜d'vaizbl] adj. 可取的 L20 agitate['✌d✞iteit] v. 摇动L 2 a large extent 很大程度L4,1 3 algorithm ['✌l♈☜ri❆☜m] n. 算法L 6 align [☜'lain] v 定位，调准L17 alignment[☜'lainm☜nt] n. 校直L1 1 all-too-frequent 频繁L17 allowance[☜'l☜uens] n. 容差, 余量L5 alternate[' :lt☜nit]v.交替,轮流L 1 alternative[ :l't☜:n☜tiv] n. 替换物L 3 alternatively[ :l't☜:n☜tivli] ad. 做为选择, 也许L 5 aluminiun[ ✌lju'minj☜m] n.铝L 2 ample['✌mpl] adj. 充足的L20 analysis [☜'n✌l☜sis] n. 分析L 6 ancillary['✌nsil☜ri] a.补助的, 副的L 4 angular ['✌♈jul☜] adj. 有角的L20 annealing[☜'li:li☠] n.退火L 2 aperture ['✌p☜t☞☜] n.孔L17 applied loads 作用力L 1 ap p rop riat e [☜'p r☜up rieit] a. 适当的L6,20 arc[a:k] n.弧, 弓形L10 arise[☜'raiz] vi. 出现, 发生L2 1 arrange[☜'reid✞] v. 安排L1 2 article['a:tikl] n.制品, 产品L2 1 ascertain[ ✌s☜'tein] vt. 确定, 查明L 1 assemble[☜'sembl] vt.组装L 4 attitude ['✌titju:d] n 态度L17 auxiliary [ :♈'zilj☜ri]adj. 辅助的L8 avoid[☜'v id] v.避免L7 axis['✌ksis] n.轴L 5 axle['✌ksl] n.轮轴, 车轴L 1Bbackup['b✌k ✈p] n. 备份L9 batch [b✌t☞] n 一批L17 bearing['b☪☜ri☠] n.轴承,支座L2 1 bed[bed] n. 床身L 5 behavior[bi'heivj☜] n. 性能L 1 bench-work 钳工工作L 4 bend[bend] v.弯曲L 1 beneath[bi'ni: ] prep在···下L 4 bin [bin] n. 仓，料架L19 blank [bl✌☠k] n. 坯料L20 blank [bl✌☠k] v. 冲裁,落料L17 blanking tool 落料模L17 blast [bl✈st] n.一阵（风）L18 blemish['blemi☞] n. 缺点, 污点L1 3 bolster['b☜ulst☜] n. 模座,垫板L4,5 boost[bu:st] n. 推进L9 boring['b :ri☠] n.镗削, 镗孔L4, 5 bracket ['br✌kit] n. 支架L19 brass [br✌s] n.黄铜L 2 break down 破坏L 1 breakage ['breikid✞] n.破坏L17 bridge piece L1 6 brine[brain] n. 盐水L 2 brittle['britl] adv.易碎的L 1121buffer [b✈f☜] n.缓冲器L8 built-in 内装的L9 bulging [b✈ld✞i☠] n. 凸肚L2 2 burr [b☜:] n. 毛刺L17 bush [bu☞] n. 衬套L17 bush[bu☞]n. 衬套L 5 by far (修饰比较级, 最高级)···得多, 最L 3 by means of 借助于L 5Ccabinet ['k✌binit] n.橱柜L7 call upon 要求L17 carbide['ka:baid] n.碳化物L10 carburzing['ka:bjureti☠] n. 渗碳L 2 carriage['k✌rid✞] n.拖板, 大拖板L 5 carry along 一起带走L18 carry down over 从···上取下L2 1 carry out 完成L17 case hardening 表面硬化L 2 case[keis] n. 壳, 套L 2 cast steel 铸钢L17 casting['ka:sti☠] n. 铸造,铸件L 3 category['k✌t☜♈☜uri] n. 种类L6,1 5 caution ['k :☞☜n] n. 警告，警示L17 cavity and core plates 凹模和凸模板L1 1 cavity['k✌viti] n.型腔, 腔, 洞L4,10 centre-drilling 中心孔L 5 ceramic[si'r✌mik] n.陶瓷制品L 3 chain doted line 点划线L1 1 channel['t☞✌nl] n.通道, 信道L8 characteristic[k✌r☜kt☜'ristik] n.特性L 1 check[t☞ek] v.核算L2 1 chip[t☞ip] n.切屑, 铁屑L 3 chuck [t☞✈k] n.卡盘L5,8 chute [☞u:t] n. 斜道L19 circa ['s☜k☜:] adv. 大约L7 circlip['s☜:klip] n.(开口)簧环L2 2 circuit['s☜:kit] n. 回路, 环路L1 3 circular supoport block L 5 circulate['s☜:kjuleid] v.(使)循环L1 3 clamp [kl✌mp] vt 夹紧L17 clamp[kl✌mp] n.压板L1 2 clay[klei] n. 泥土L2,7 clearance ['kli☜r☜ns] n. 间隙L17 clip [klip] vt. 切断，夹住L19 cold hobbing 冷挤压L 4 cold slug well 冷料井L1 2 collapse[k☜'l✌ps] vi.崩塌, 瓦解L2 2 collapsible[k☜'l✌ps☜bl] adj.可分解的L2 2 combination [k mbi'nei☞☜n] n. 组合L18 commence[k☜'mens] v. 开始, 着手L1 6 commence[k☜'mens]v. 开始L2 1 c ommercial [k☜'m☜:☞☜l] adj. 商业的L7 competitive[k☜m'petitiv] a. 竞争的L9 complementary[ k mpli'ment☜ri] a. 互补的L 5 complexity [kem'pleksiti] n.复杂性L8 c o m p l i c at ed['k mp l☜keit id] adj.复杂的L2 complication [k mpli'kei☞☜n] n. 复杂化L5,20 compression [k☜m'pre☞☜n] n.压缩L 1 comprise[k☜m'prais] vt.包含L1 6 compromise['k mpr☜maiz] n. 妥协, 折衷L1 3 concern with 关于L 6 concise[k☜n'sais] a. 简明的, 简练的L9 confront[k☜n'fr✈nt] vt. 使面临L1 4 c o n n e c t or[k☜'nekt☜] n. 连接口, 接头L14 consequent['k nsikw☜nt] a. 随之发生的, 必然的L 3 console ['k nsoul] n.控制台L8 consume [k☜n'sjum] vt. 消耗, 占用L7 consummate [k☜n's✈meit] vt. 使完善L 6 container[k☜n'tein☜] n. 容器L1 1 c o n t i n gent[ken't ind✞☜nt] a.可能发生的L9 contour['k☜ntu☜] n.轮廓L5,2 1122c o nvent ional[k☜n'ven☞☜nl] a. 常规的L4 converge[k☜n'v☜:d✞] v.集中于一点L2 1 conversant[k n'v☜:s☜nt] a. 熟悉的L1 5 conversion[k☜n'v☜:☞☜n] n 换算, 转换L7 conveyer[ken'vei☜] n. 运送装置L1 2 coolant['ku:l☜nt] n. 冷却液L1 3 coordinate [k☜u' :dnit] vt. (使)协调L8 c o p y m a c h i n e仿形(加工)机床L4 core[k :] n. 型芯, 核心L2, 4 corresponding [ka:ri'sp di☠] n.相应的L7 counteract [kaunt☜'r✌kt] vt. 反作用,抵抗L20 couple with 伴随L20 CPU (central processing unit) 中央处理器L9 c r a c k[k r✌k] v.（使）破裂，裂纹L1,17 critical['kritikl] adj.临界的L 2 cross-hatching 剖面线L1 6 cross-section drawn 剖面图L1 1 cross-slide 横向滑板L 5 C R T(c a t h o d er-ray t ube) 阴极射线管L9 crush[kr✈☞]vt.压碎L 1 cryogenic[ krai☜'d✞enik ]a.低温学的 L 1 crystal['kristl] adj.结晶状的L 1 cubic['kju:bik] a. 立方的, 立方体的L 3 cup [k✈p] vt (使)成杯状, 引伸L18 curable ['kjur☜bl] adj. 可矫正的L20 curvature['k☜:v☜t☞☜] n.弧线L2 1 curve [k☜:v] vt. 使弯曲L20 cutter bit 刀头, 刀片L 3 cyanide['sai☜naid] n.氰化物L 2Ddash [d✌☞] n. 破折号L 6 daylight ['deilait] n. 板距L1 2 decline[di'klain] v.下落,下降,减少, L3,9 deform[di'f :m] v. (使)变形L1, 3 demonstrate['dem☜streit ] v证明L2 1 depict[di'pikt ] vt 描述L18 deposite [di'p zit] vt. 放置L20 depression[di'pre☞☜n] n. 凹穴L1 2 descend [di'sent] v. 下降L20 desirable[di'zair☜bl] a. 合适的L 2 detail ['diteil] n.细节，详情L17 deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 恶化L1 2 determine[di't☜:min] v.决定L1 6 diagrammmatic[ dai☜gr☜'m✌tik].a.图解的，图表的L10 dictate['dikteit] v. 支配L1 2 die[dai] n.模具, 冲模, 凹模L 2 dielectric[daii'lektrik] n. 电介质L10 die-set 模架L19 digital ['did✞itl ] n.数字式数字, a.数字的L3, 6 dimensional[dddi'men☞☜nl] a. 尺寸的, 空间的L 3 discharge[dis't☞a:d✞] n.v. 放电, 卸下, 排出L 3 discharge[dis't☞a:d✞] v.卸下L8 d i s c r e t e[dis'cri:t] adj. 离散的,分立的L7 dislodge[dis'l d✞] v. 拉出, 取出 L1 2 dissolution[dis☜'lu:☞☜n] n.结束L9 distinct [dis'ti☠kt] a.不同的，显著的L 6 distort [dis'd :t] vt. 扭曲L20 distort[dis't :t] vt. (使)变形, 扭曲L 1 distributed system 分布式系统L9 dowel ['dau☜l] n. 销子L19 d r a m a t i c l l y[dr☜'m✌t ikli] adv. 显著地L7 drastic ['dr✌stik] a.激烈的L17 draughting[dra:fti☠] n. 绘图L1 6 draughtsman['dr✌ftsm☜n] n. 起草人L1 6 drawing['dr :i☠] n. 制图L1 1 drill press 钻床L8 drum [dr✈m] n.鼓轮L8 dual ['dju:☜l] adv. 双的，双重的 L18 ductility [d✈k'tiliti ] n.延展性L1,2 1123dynamic [dai'n✌mik ] adj 动力的L 6Eedge [ed✞] n .边缘L20 e.g.(exempli gratia) [拉] 例如L1 2 ejector [i'd✞ekt☜] n.排出器，L18 ejector plate 顶出板L1 6 ejector rob 顶杆L 5 elasticity[il✌'stisiti] n.弹性L 1 e l e c t r i c dicharge machining 电火花加工L3electrical discharge machining电火花加工L10 e l e c t r o c h e m i c a l machining 电化学加工L3 electrode[i'lektr☜ud] n. 电极L10 electro-deposition 电铸L 4 elementary [el☜'ment☜ri] adj.基本的L 2 eliminate[i'limineit] vt. 消除, 除去L10 elongate[i'l ☠♈et] vt. (使)伸长, 延长L 1 emerge [i'm☜:d✞] vi. 形成, 显现 L20 emphasise['emf☜saiz] vt. 强调L 4 endeavour[en'dev☜] n. 尽力L17 engagement[in'♈eid✞ment] n. 约束, 接合L2 2 enhance[in'h✌ns] vt. 提高, 增强L9 ensure [in'☞u☜] vt. 确保，保证L17 envisage[in'vizid✞] vt.设想L1 5 erase[i'reis] vt. 抹去, 擦掉L1 6 evaluat ion[i'v✌lju ei☞☜n] n. 评价, 估价L1 eventually[i'v☜nt☞u☜li ] adv.终于L2 1 evolution[ev☜'lu:☞☜n] n.进展L1 6 excecution[eksi'kju:☞☜n] n. 执行, 完成L9 execute ['ekskju:t] v. 执行L8 exerte [i♈'z☜:t] vt. 施加L20 experience[iks'piri☜ns] n. 经验L1 6 explosive[iks'pl☜usiv]adj.爆炸(性)的L2 2 extend[eks'tend] v. 伸展L 2 external[eks't☜:nl] a. 外部的L5,1 1 extract[eks'tr✌kt] v. 拔出L1 4 extreme[iks'tri:m] n. 极端L1 3 extremely[iks'tri:mli] adv. 非常地 L1 2 extremity[iks'tmiti] n. 极端L1 3 extrusion[eks'tru:✞☜n] n. 挤压, 挤出L 3FF (Fahrenheit)['f✌r☜nhait]n.华氏温度L2 fabricate ['f✌brikeit] vt.制作,制造L7 facilitate [f☜'siliteit] vt. 帮助L 6 facility[f☜'siliti] n. 设备L 4 facing[feisi☠] n. 端面车削L 5 fall within 属于, 适合于L1 5 fan[f✌n] n.风扇L7 far from 毫不, 一点不, 远非L9 fatigue[f☜'ti♈] n.疲劳L 1 feasible ['fi:z☜bl] a 可行的L18 feature ['fi:t☞☜] n.特色, 特征L7,17 feed[fi:d] n.. 进给L 5 feedback ['fi:db✌k] n. 反馈L8 female['fi:meil] a. 阴的, 凹形的L1 1 ferrule['fer☜l] n. 套管L1 4 file system 文件系统L9 fitter['fit☜] n.装配工, 钳工L 4 fix[fiks] vt. 使固定, 安装, vi. 固定L1 1 fixed half and moving half 定模和动模L1 1 f l a t-p a n e l t e c h n o l ogy平面(显示)技术L9 f l e xi b i l it y[fleksi'bilit i] n. 适应性, 柔性L9 flexible['fleks☜bl] a. 柔韧的L1 3 flow mark 流动斑点L13 follow-on tool 连续模L18 f o r e go i n g ['f :'♈☜ui☠]adj. 在前的,前面的L8 f o r e t e l l[f :'t ell] vt. 预测, 预示, 预言L9 forge[f :d✞] n. v. 锻造L 3 forming[f :mi☠] n. 成型L 3 four screen quadrants 四屏幕象限L9 fracture['fr✌kt☞☜] n.破裂L2 1124free from 免于L2 1Ggap[♈✌p] n. 裂口, 间隙L10 gearbox['♈i☜b ks] n.齿轮箱L 5 general arrangement L1 6 govern['♈✈v☜n] v.统治, 支配, 管理 L1 3 grain [♈rein] n. 纹理L20 graphic ['♈r✌fik] adj. 图解的L 6 grasp [♈r✌sp] vt. 抓住L8 grid[♈rid] n. 格子, 网格L1 6 grind[♈raind] v. 磨, 磨削, 研磨L 3 gr i n d i n g ['♈raindi☠] n. 磨光,磨削L3,20 grinding machine 磨床L 5 gripper[♈rip☜] n. 抓爪, 夹具L9 groove[♈ru:v] n. 凹槽L1 2 guide bush 导套L 5 guide pillar 导柱L 5 guide pillars and bushes 导柱和导套L1 1Hhandset['h✌ndset] n. 电话听筒L 4 hardness['ha:dnis] n.硬度L1, 2 hardware ['ha:dw☪☜] n. 硬件L 6 h e a d s t o c k['h e d s t k] n.床头箱, 主轴箱L5 hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的L1 1 h i n d r a n c e['h i n d r☜ns] n.障碍, 障碍物L11 hob[h b] n. 滚刀, 冲头L 4 hollow-ware 空心件L2 1 horizontal[h ri'z ntl] a. 水平的L1 6 hose[h☜uz] n. 软管, 水管L1 3 hyperbolic [haip☜'b lik] adj.双曲线的L7Ii.e. (id est) [拉] 也就是L1 2 identical[ai'dentikl] a同样的L1 6 identify [ai'dentifai] v. 确定, 识别L7 idle ['aidl] adj.空闲的L8 immediately[i'mi:dj☜tli] adv. 正好, 恰好L1 2 impact['imp✌kt] n.冲击L 1 impart [im'pa:t] v.给予L11,17 implement ['implim☜nt] vt 实现L 6 impossibility[imp s☜'biliti] n.不可能L2 1 impression[im'pre☞☜n] n. 型腔L1 1 in contact with 接触L 1 in terms of 依据L 1 inasmuch (as)[in☜z'm✈t☞] conj.因为, 由于L 3 inch-to-metric conversions 英公制转换L7 inclinable [in'klain☜bl] adj. 可倾斜的L20 inclusion [in'klu☞☜n] n. 内含物L19 inconspicuous[ink☜n'spikju☜s] a. 不显眼的L1 4 incorp orat e [in'k :p☜reit] v 合并,混合L17 indentation[ inden'tei☞☜n ] n.压痕L 1 indenter[in'dent☜] n. 压头L 1 independently[indi'pein☜ntli] a. 独自地, 独立地L1 6 inevitably[in'evit☜bli] ad. 不可避免地L1 4 inexpensive[inik'spensiv]adj. 便宜的L 2 inherently [in'hi☜r☜ntli] adv.固有的L7 injection mould 注塑模L1 1 injection[in'd✞ek☞☜n] n. 注射L1 1 in-line-of-draw 直接脱模L1 4 insert[in's☜:t] n. 嵌件L1 6 inserted die 嵌入式凹模L19 inspection[in'spek☞☜n] n.检查,监督L9 installation[inst☜'lei☞☜n] n. 安装L10 integration [inti'♈rei☞☜n] n.集成L 6 intelligent[in'telid✞☜nt]a. 智能的L9 intentinonally [in'ten☞☜n☜li] adv 加强地，集中地L17 interface ['int☜feis] n.. 界面L 6 internal[in't☜:nl] a. 内部的L1, 5 int erp olat ion [int☜p☜'lei☞☜n] n.插值法L7 investment casting 熔模铸造L 4125irregular [i'regjul☜] adj. 不规则的，无规律L17 irrespective of 不论, 不管L1 1 irrespective[iri'spektiv] a. 不顾的, 不考虑的L1 1 issue ['isju] vt. 发布，发出L 6Jjoint line 结合线L1 4Kkerosene['ker☜si:n] n.煤油L10 keyboard ['ki:b :d ] n. 健盘L 6 knock [n k] v 敲，敲打L17Llance [la:ns] v. 切缝L19 lathe[lei❆] n. 车床L 4 latitude ['l✌titju:d] n. 自由L17 lay out 布置L1 3 limitation[limi'tei☞☜n] n.限度,限制,局限(性)L 3 local intelligence局部智能L9 locate [l☜u'keit] vt. 定位L18 logic ['l d✞ik] n. 逻辑L7 l ongit udinal['l nd✞☜'t ju:dinl] a. 纵向的L5 longitudinally['l nd✞☜'tju:dinl] a. 纵向的L1 3 look upon 视作, 看待L17 lubrication[lju:bri'kei☞☜n ] n.润滑L2 1Mmachine shop 车间L 2 machine table 工作台L8 machining[m☜'☞i:ni☠] n. 加工L 3 made-to-measure 定做L1 5 m a i n t e n a n c e['m eint in☜ns] n.维护,维修L7 majority[m☜'d✞a:riti] n.多数L2 1 make use of 利用L 2 male[meil] a. 阳的, 凸形的L1 1 malfunction['m✌l'f✈☠☞☜n] n. 故障L9 mandrel['m✌dtil] n.心轴L2 2manifestation[m✌nif☜s'tei☞☜n] n. 表现, 显示L9 m a s s i v e n e s s['m✌sivnis ] 厚实，大块L19 measure['me✞☜] n. 大小, 度量L 1 microcomputer 微型计算机L9 microns['maikr n] n.微米L10 microprocessor 微处理器L9 mild steel 低碳钢L17 milling machine 铣床L 4 mineral['min☜r☜l] n.矿物, 矿产L 2 minimise['minimaiz] v.把···减到最少, 最小化L1 3 minute['minit] a.微小的L10 mirror image 镜像L1 6 mirror['mir☜] n. 镜子L1 6 MIT (Massachusetts Institute of Technology) 麻省理工学院L7 moderate['m d☜rit]adj. 适度的L1, 2 modification [m difi'kei☞☜n ] n. 修改, 修正L 6 modulus['m djul☜s] n.系数L 1 mold[m☜uld] n. 模, 铸模, v. 制模, 造型L 3 monitor ['m nit☜ ] v. 监控L 6 monograph['m n☜♈ra:f] n. 专著L 4 more often than not 常常L20 motivation[m☜uti'vei☞☜n] n. 动机L9 mould split line 模具分型线L1 2 moulding['m☜udi☠] n. 注塑件L5,1 1 move away from 抛弃L17 multi-imprssion mould 多型腔模L1 2Nnarrow['n✌r☜u] a. 狭窄的L1 2 NC (numerical control ) 数控L7 nevertheless[ nev☜❆☜'les] conj.,adv.然而,不过L1 1 nonferrous['n n'fer☜s] adj.不含铁的, 非铁的L 2126normally['n :mli]adv.通常地L2 2 novice['n vis] n. 新手, 初学者L1 6 nozzle['n zl] n. 喷嘴, 注口L1 2 numerical [nju'merikl] n. 数字的L 6Oobjectionable [☜b'd✞ek☞☜bl] adj. 有异议的，讨厌的L17 observe[☜b'z☜:v] vt. 观察L 2 obviously [' bvi☜sli] adv 明显地L17 off-line 脱机的L 6 on-line 联机L9 operational [ p☜'rei☞☜nl] adj.操作的, 运作的L8 opportunity[ p☜'tju:niti] n. 时机, 机会L1 3 o p p osing[☜'p☜uz i☠] a.对立的, 对面的L12 opposite[' p☜zit] n. 反面L1a.对立的,对面的L1 2 op t imiz at ion [ p t imai'z ei☞☜n] n.最优化L6 orient [' :ri☜nt] vt. 确定方向L8 orthodox [' : ☜d ks] adj. 正统的，正规的L19 o v e r a l l['☜uv☜r :l] a.全面的,全部的L8,13 overbend v.过度弯曲L20 overcome[☜uv☜'k✈m] vt.克服, 战胜L10 overlaping['☜uv☜'l✌pi☠] n. 重叠L 4 overriding[☜uv☜'raidi☠] a. 主要的, 占优势的L1 1Ppack[p✌k] v. 包装L 2 package ['p✌kid✞] vt.包装L7 pallet ['p✌lit] n.货盘L8 panel ['p✌nl] n.面板L7 paraffin['p✌r☜fin] n. 石蜡L10 parallel[p✌r☜lel] a.平行的L 5 penetration[peni'trei☞☜n ] n.穿透L 1 peripheral [p☜'rif☜r☜l] adj 外围的L 6 periphery [p☜'rif☜ri] n. 外围L18 permit[p☜'mit] v. 许可, 允许L1 6 pessure casting 压力铸造L 4 pillar['pil☜] n. 柱子, 导柱L5,17 pin[pin] n. 销, 栓, 钉L5,17 pin-point gate 针点式浇口L1 2 piston ['pist☜n] n.活塞L 1 plan view 主视图L1 6 plasma['pl✌zm☜] n. 等离子L9 plastic['pl✌stik] n. 塑料L 3 platen['pl✌t☜n] n. 压板L1 2 plotter[pl t☜] n. 绘图机L9 plunge [pl✈nd✞] v翻孔L18 plunge[pl✈nd✞] v.投入L 2 plunger ['pl✈nd✞☜ ] n. 柱塞L19 pocket-size 袖珍L9 portray[p :'trei] v.描绘L2 1 pot[p t] n.壶L2 1 pour[p :] vt. 灌, 注L2 2 practicable['pr✌ktik☜b] a. 行得通的L1 4 preferable['pref☜r☜bl] a.更好的, 更可取的L 3 preliminary [pri'limin☜ri] adj 初步的，预备的L19 press setter 装模工L17 p r e s s[p r e s]n.压,压床,冲床,压力机L2,8 prevent [pri'vent] v. 妨碍L20 primarily['praim☜rili] adv.主要地L 4 procedure[pr☜'si:d✞☜] n.步骤, 方法, 程序L2,1 6 p roduct ivit y.[p r☜ud✈k't ivit i] n. 生产力L9 profile ['pr☜ufail] n.轮廓L10 progressively[pr☜'♈resiv] ad.渐进地L1 5 project[pr☜'d✞ekt] n.项目L 2 project[pr☜'d✞ekt] v. 凸出L1 1 projection[pr☜'d✞ek☞☜n] n.突出部分L2 1 proper['pr p☜] a. 本身的L10 property['pr p☜ti] n.特性L 1 prototype ['pr☜ut☜taip] n. 原形L7127proximity[pr k'simiti] n.接近L9 prudent['pru:d☜nt] a. 谨慎的L1 6 punch [p✈nt☞] v. 冲孔L 3 punch shapper tool 刨模机L17 punch-cum-blanking die 凹凸模L18 punched tape 穿孔带L 3 purchase ['p☜:t☞☜s] vt. 买，购买L 6 push back pin 回程杆L 5 pyrometer[pai'n mit☜] n. 高温计L 2Qquality['kwaliti] n. 质量L1, 3 quandrant['kw dr☜nt] n. 象限L9 quantity ['kw ntiti] n. 量，数量L17 quench[kwent☞] vt. 淬火L 2Rradial['reidi☜l] adv.放射状的L2 2 ram [r✌m] n 撞锤. L17 rapid['r✌pid]adj. 迅速的L 2 rapidly['r✌pidli]adv. 迅速地L 1 raster['r✌st☜] n. 光栅L9 raw [r :] adj. 未加工的L 6 raw material 原材料L 3 ream [ri:m] v 铰大L17 reaming[ri:mi☠] n. 扩孔, 铰孔L8 recall[ri'k :l] vt. 记起, 想起L1 3 recede [ri'si:d] v. 收回, 后退L20 r e c e s s[r i's e s]n. 凹槽,凹座,凹进处L4,18 redundancy[ri'd✈nd☜nsi] n. 过多L9 re-entrant 凹入的L1 2 r e f e r[r i'f☜:]v.指, 涉及, 谈及L1,12 reference['ref☜r☜ns] n.参照,参考L2 1 refresh display 刷新显示L9 register ring 定位环L1 1 r e gi s t e r['red✞st☜] v. 记录, 显示, 记数L2 regrind[ri:'♈aind](reground[ri:'gru:nd]) vt. 再磨研L1 2 relative['rel☜tiv] a. 相当的, 比较的L1 2 relay ['ri:lei] n. 继电器L7 release[ri'li:s] vt. 释放L1relegate['rel☜geit] vt. 把··降低到L9 reliability [rilai☜'biliti] n. 可靠性L7 relief valves 安全阀L2 2 relief[ri'li:f] n.解除L2 2 relieve[ri'li:v ]vt.减轻, 解除L 2 remainder[ri'meind☜] n. 剩余物, 其余部分L 4 removal[ri'mu:vl] n. 取出L1 4 remove[ri'mu:v] v. 切除, 切削L 4 reposition [rip☜'zi☞☜n] n.重新安排L17 represent[ repri'zent☜] v 代表,象征L1 1 reputable['repjut☜bl] a. 有名的, 受尊敬的L1 5 reservoir['rez☜vwa: ] n.容器, 储存器L2 2 resident['rezid☜nt] a. 驻存的L9 resist[ri'zist] vt.抵抗L 1 resistanc e[ri'zist☜ns] n.阻力, 抵抗L1 resolution[ rez☜'lu:☞☜n] n. 分辨率L9 r e s p e c t i v e[ri'sp ekt iv] a.分别的,各自的L11 respond[ris'p nd] v.响应, 作出反应L9 responsibility[risp ns☜'biliti] n.责任L1 3 restrain[ris'trein]v.抑制L2 1 restrict [ris'trikt] vt 限制，限定L18 restriction[ris'trik☞☜n] n. 限制L1 2 retain[ri'tein] vt.保持, 保留L2,1 2 retaining plate 顶出固定板L1 6 reveal [ri'vil] vt.显示，展现L17 reversal [ri'v☜sl] n. 反向L1,20 right-angled 成直角的L20 rigidity[ri'd✞iditi] n. 刚度L 1 rod[r d] n. 杆, 棒L1, 5 rotate['r☜uteit] vt.(使)旋转L 5 rough machining 粗加工L 5 rough[r✈f] a. 粗略的L5,2 1 routine [ru:'ti:n] n. 程序L7 rubber['r✈b☜] n.橡胶L3,2 2 runner and gate systems 流道和浇口系统128L1 1Ssand casting 砂型铸造L 3 satisfactorily[ s✌tis'f✌ktrili] adv. 满意地L 1 saw[a :] n. 锯子L 4 scale[skeil]n. 硬壳L 2 score[sk :] v. 刻划L1 4 s c r a p[s k r✌p]n.废料,边角料, 切屑L2,3 screwcutting 切螺纹L 4 seal[si:l] vt.密封L2 2 secondary storage L9 section cutting plane 剖切面L1 6 secure[si'kju☜] v.固定L2 2 s e c u r e[s i'kju☜] vt.紧固,夹紧,固定L5,22 segment['se♈m☜nt] v. 分割L10 sensitive['sensitiv]a.敏感的L1,7 sequence ['si:kw☜ns] n. 次序L 6 sequential[si'kwen☞☜l] a.相继的L1 6 seriously['si☜ri☜sli] adv.严重地L 1 servomechanism ['s☜:v☜'mek☜nizm] n.伺服机构L7 Servomechanism Laboratoies 伺服机构实验室L7 servomot or ['s☜:v☜m☜ut☜] n.伺服马达L8 setter ['set☜] n 安装者L17 set-up 机构L20 sever ['sev☜] v 切断L17 severity [si'veriti] n. 严重L20 shaded[☞✌did] adj.阴影的L2 1 shank [☞✌☠k] n. 柄. L17 shear[☞i☜]n.剪,切L 1 shot[☞t] n. 注射L1 2 shrink[☞ri☠k] vi. 收缩L1 1 side sectional view 侧视图L1 6 signal ['si♈nl] n.信号L8 similarity[simi'l✌riti] n.类似L1 5 simplicity[sim'plisiti] n. 简单L1 2 single-point cutting tool 单刃刀具L 5 situate['sitjueit] vt. 使位于, 使处于L1 1 slide [slaid] vi. 滑动, 滑落L20 slideway['slaidwei] n. 导轨L 5 slot[sl t] n. 槽L 4 slug[sl✈♈] n. 嵌条L1 2 soak[s☜uk] v. 浸, 泡, 均热L 2 software ['s ftw☪☜] n. 软件L 6 solid['s lid] n.立体, 固体L9 solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化L1 3 solution[s☜'lu:☞☜n] n.溶液L 2 sophisiticated [s☜'fistikeitid] adj.尖端的,完善的L8 sound[saund] a. 结实的, 坚固的) L 1 spark erosion 火花蚀刻L10 spindle['spindl] n. 主轴L5,8 spline[splain] n.花键L 4 split[split] n. 侧向分型, 分型L12,1 4 spool[spu:l] n. 线轴L1 4 springback n.反弹L20 spring-loaded 装弹簧的L18 sprue bush 主流道衬套L1 1 sprue puller 浇道拉杆L1 2 square[skw☪☜] v. 使成方形L 4 stage [steid✞] n. 阶段L16,19 standardisation[ st✌nd☜dai'zei☞☜n] n. 标准化L1 5 startling['sta:tli☠] a. 令人吃惊的L10 steadily['sted☜li ] adv. 稳定地L2 1 step-by-step 逐步L8 stickiness['stikinis] n.粘性L2 2 stiffness['stifnis] n. 刚度L 1 stock[st k] n.毛坯, 坯料L 3 storage tube display 储存管显示L9 storage['st :rid✞] n. 储存器L9 s t r aight forward[st reit'f :w☜d]a.直接的L10 strain[strein] n.应变L 1129strength[stre☠] n.强度L 1 stress[stres] n.压力,应力L 1 stress-strain应力--应变L 6 stretch[stret☞] v.伸展L1,2 1 strike [straik] vt. 冲击L20 stringent['strind✞☜nt ] a.严厉的L2 2 stripper[strip☜] n. 推板L1 5 stroke[strouk] n. 冲程, 行程L1 2 structrural build-up 结构上形成的L1 1 sub-base 垫板L19 subject['s✈bd✞ikt] vt.使受到L2 1 submerge[s☜b'm☜:d✞] v.淹没L2 2 subsequent ['s✈bsikwent] adj. 后来的L20 subsequently ['s✈bsikwentli] adv. 后来, 随后L 5 substantial[s☜b'st✌n☞☜l] a. 实质的L10 substitute ['s✈bstitju:t] vt. 代替,.替换L7 subtract[s☜b'tr✌kt] v.减, 减去L1 5 s u i t a b l e['s u:t☜b l] a. 合适的, 适当的L5 suitably['su:t☜bli] ad.合适地L1 5 sunk[s✈☠k](sink的过去分词) v. 下沉, 下陷L1 1 superior[s☜'pi☜ri☜] adj.上好的L2 2 s u scep t ible[s☜'sep t☜bl] adj.易受影响的L7 sweep away 扫过L17 symmetrical[si'metrikl] a. 对称的L1 4 s y n c hroniz e ['si☠kr☜naiz] v.同步,同时发生L8Ttactile['t✌ktail] a. 触觉的, 有触觉的L9 tailstock['teilst k] n.尾架L 5 tapered['teip☜d] a. 锥形的L1 2 tapping['t✌pi☠] n. 攻丝L8 technique[tek'ni:k] n. 技术L1 6 tempering['temp☜r☠] n.回火L 2 tendency['tend☜nsi] n. 趋向, 倾向L1 3 t ensile['tensail] a.拉力的, 可拉伸的L2 拉紧的, 张紧的L 1 tension ['ten☞☜n] n.拉紧,张紧L 1 terminal ['t☜:m☜nl ] n. 终端机L 6 terminology[t☜:mi'n l☜d✞i ] n. 术语, 用辞L1 1 theoretically [ i:☜'retikli ] adv.理论地L2 1 thereby['❆☪☜bai] ad. 因此, 从而L1 5 t hermoplastic[' ☜:m☜u'pl✌stik] a. 热塑性的, n. 热塑性塑料L 3 thermoset[' ☜:m☜set] n.热固性L1 2 thoroughly[' ✈r☜uli] adv.十分地, 彻底地L 2 thread pitch 螺距L 5 thread[ red] n. 螺纹L 5 thrown up 推上L17 tilt [tilt] n. 倾斜, 翘起L20 tolerance ['t l☜r☜ns] n..公差L17 tong[t ☠] n. 火钳L 2 tonnage['t✈nid✞] n.吨位, 总吨数L 3 tool point 刀锋L 3 tool room 工具车间L10 t o o l h o l d e r['t u:lh☜uld☜] n.刀夹,工具柄L5 t o o l m a k er ['t u:l'meik☜] n 模具制造者L17 toolpost grinder 工具磨床L 4 toolpost['tu:l'p☜ust] n. 刀架L 4 torsional ['t :☞☜nl] a扭转的. L 1 toughness['t fnis] n. 韧性L 2 trace [treis] vt.追踪L7 tracer-controlled milling machine 仿形铣床L 4 transverse[tr✌ns'v☜:s] a. 横向的L 5 tray [trei] n. 盘，盘子，蝶L19 treatment['tri:tm☜nt] n.处理L 2 tremendous[tri'mend☜s] a. 惊人的, 巨大的L9 trend [trend] n.趋势L7 trigger stop 始用挡料销L17 tungsten['t✈☠st☜n] n.钨L10 turning['t☜:ni☠] n.车削L4, 5130模具英语词汇表131twist[twist ] v.扭曲，扭转 L 1 two-plate mould 双板式注射模L 12 Uultimately['✈ltimitli] adv 终于. L 6 undercut moulding 侧向分型模 L 1 4 undercut['✈nd ☜k ✈t] n. 侧向分型 L 1 4 undercut['✈nd ☜k ✈t] n.底切 L 1 2 underfeed['✈nd ☜'fi:d] a, 底部进料的 L 15 undergo[✈nd ☜'♈☜u] vt.经受L 1 underside['✈nd ☜said] n 下面,下侧L1 1 u n d u e [✈n 'd j u :] a.不适当的, 过度的 L4,10 uniform['ju:nif :m] a.统一的, 一致的 L 12 utilize ['ju:tilaiz] v 利用L17Utopian[ju't ☜upi ☜n] adj.乌托邦的, 理想化的L 2 1 Vvalve[v ✌lv] n.阀L22vaporize['veip ☜raiz] vt.vi. 汽化, (使)蒸发L10 variation [v ☪☜ri'ei ☞☜n] n. 变化L 20v a rious ['v ☪☜ri ☜s] a.不同的,各种的 L1,20 vector feedrate computation 向量进刀速率计算L 7 vee [vi:] n. v 字形L 20 velocity[vi'l siti] n.速度L1versatile['v ☜s ☜tail] a.多才多艺的,万用的L5,8 vertical['v ☜:tikl] a. 垂直的 L 16 via [vai ☜] prep.经,通过 L 8 vicinity[v ☜'siniti] n.附近L 1 3 viewpoint['vju:p int] n. 观点L 4 Wwander['w nd ☜] v. 偏离方向 L 1 3 warp[w :p] v. 翘曲 L 2 washer ['w ☞☜] n. 垫圈L 18 wear [w ☪☜] v.磨损 L 7 well line 结合线L1 3 whereupon [hw ☪☜r ☜'p n] adv. 于是 L19 winding ['waindi ☠] n. 绕, 卷 L 8 with respect to 相对于 L 1,5 w i t h s t a n d [w i ❆'s t ✌n d ] vt.经受,经得起 L1work[w ☜:k] n. 工件 L 4 workstage 工序L 19 wrinkle['ri ☠kl] n.皱纹vt.使皱L 2 1 Yyield[ji:ld] v. 生产L 9 Zzoom[zu:] n. 图象电子放大L9。
模具英语专业术语分析解析
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate 牛角浇口：Horn gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;Torpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure 开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance。
模具专业英语词汇
Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。
模具英语专业术语
模具英语专业术语如下：1. 模具：Mold，Die2. 模具设计：Mold Design3. 模具制造：Mold Manufacturing4. 模具工程师：Mold Engineer5. 模具材料：Mold Material6. 耐磨材料：wear-resistant material7. 热处理：Heat Treatment8. 水路设计：Water Path Design9. 浇注系统：Injection Sleeve10. 冷却系统：Cooling System11. 顶出系统：Pop-out System12. 复位系统：Reset System13. 导向机构：Guide Device14. 模板：Base Plate15. 顶杆：Pushrod16. 复位杆：Reset Rod17. 斜导柱：Oblique Guide Column18. 导套：Guide Bushing19. 滑块：Slider20. 镶针：Pillow Block21. 弹簧：Spring22. 皮囊弹簧：Kelvin Spring23. 油压缓冲器：Hydraulic Buffer24. 压力表：Pressure Gauge25. 安全阀：Safety Valve26. 水路板：Waterway Plate27. 分流器：Flow Divider28. 水口：Filler Port29. 冷料穴：Cold Molding Chamber30. 模具钢：Mold Steel31. SKH-55、SKH-55M、高速工具钢、HSS等。
32. SKD、SKH-S、SKD61、SKH-9等。
模具钢硬度（Hardness of die steel）：布氏硬度（HB）、洛氏硬度（HRC）、维氏硬度（HV）等。
33. SKD61(级硬SKD61) ，Cr12MoV，A3，A2，SKH-9，718，738，P20等。
塑料模具钢有PXZ、SACD、S136、S718、SS446、3Cr2Mo等。
模具英语专业术语
模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。
模具专业英语词汇
模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 光滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性nài mósǔn xìng abrasive n. 磨料móliàoaccelerator n. 促进剂cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelì additive n. 添加剂tiānjiājìadhere v. 黏附niánfùadhesion n. 黏合niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíng blow molding machine n. 吹塑机chūisùjībrittle adj. 脆性cùixìngbubble n. 气泡qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢tànsù gāngcasting n. 铸造 zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngq iāngchemical resistance n. 耐化学腐蚀性nài huàxué fǔshí xìngchip v. 削xiāo，凿záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmó dūnwèicomputer aided design (CAD) n. 电脑辅助设计diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂 zhuósèjìcomposite n. 复合材料fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquè guǎndàocooling rate n. 冷却速率lěngquè sùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性nài fǔshí xìngcure v. 固化gùhuàcustom adj. 定制dìngzhìcycle time n. 循环时间xúnhuán shíjiānDdegassing n. 排气páiqìdensity n. 密度mìdùdeform v. 变形biànxíngdie n. 冲模chòngmódie casting n. 压铸yāzhù，模铸mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间zhùliú shíjiāndye n. 染料ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchū gān，推顶锁tūidǐng suǒ，脱模锁tuōmó suǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmó bǎnejection rod n. 脱模板拉杆t uōmó bǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuā jiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维增强xiānwéi zēngqiángfilm n. 薄膜báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料yìliàoflow mark n. 流痕liúhénflow rate n. 流动速率liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫pàomòfuse v. 熔合rónghéGgas assisted injection molding n. 气辅注射成型 qìfǔzhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床móchuángHheat conduction n. 热传导rè chuándàoheater band n. 加热圈jiārè quānheat treatment n. 热处理rè chǔlǐhigh density polyethylene (HDPE) n. 高密度聚乙烯gāo mìdù jùyǐxī high impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxī hobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmó holding n. 保压bǎoyāhot runner n. 热流道rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射zhùshè，注塑 zhùsùinjection molding n. 注塑成型zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力zhùsù yālìinsulated runner n. 绝热流道juérè liúdào，保温流道 bǎowēn liúdào insulation layer n. 绝热层juérè cénginternally heated runner n. 内加热流道nèi jiārè liúdàointernal void n. 内部空腔nèibù kōngqiāngJjoint n. 接头jiētóu，连接liánjiēlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdù jùyǐxī Mmelt v. 熔融róngróngmelt index n. 熔融指数róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìng manufacture v. 制造zhìzàomeld line n. 融合线rónghé xiànmetal machining n. 金属加工jīnshù jiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型móxíngmonomer n. 单体dāntǐmold n. 模具mójùmold cavity n. 模具型腔mójù xíngqiāngmold life n. 模具寿命mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójù multicolor injection molding n. 多色注塑duōsè zhùsù multigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè z hùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙NílóngOoxidation resistance n. 耐氧化性nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒu plastic n. 塑料sùliàoplasticity n. 塑性sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物（体）jùhéwù(tǐ)，高聚物gāojùwù polymerization n. 聚合jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmì zhùsùjī precision molding n. 精密模塑jīngmì mósùpreform n. 预成型yùchéngxíngpreform molding n. 预成型模塑yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型yuánxíngpunch n. 冲头chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料húiyòngliàoresin n. 树脂shùzhīrib n. 肋条lèitiáorib stiffener n. 加强肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮xiàngpírunner n. 流道liúdàorunnerless adj. 无流道 wúliúdàorunnerless injection mold n. 无流道注塑模具wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēngshort shot n. 短射duǎnshè，欠料注射 qiànliào zhùshèshot n. 注料 zhùliào，注射 zhùshèshot size n. 注塑量zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道zhùdàosteam channel n. 汽道qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变yìngbiànstreak n. 条纹tiáowén，条痕tiáohénstress n. 应力yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐngchūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆liánjiēgānTeflon n. 特氟隆Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdù thermoforming n. 热成型rèchéngxíngthermoplastic n. 热塑性塑料rèsùxìng sùliào adj. 热塑性rèsùxìng thermoset n. 热固性塑料règùxìng sùliào adj. 热固性règùxìng three-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjù gāngUultrasonic welder n. 超声波焊接机chāoshēngbō hánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型páiqìshì zhùsù chéngxíng viscosity n. 黏度niándù，黏性 niánxìngvulcanize v. 硫化liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图根据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具专业英语词汇
landed plunger mold 有肩柱塞式模具 burnishing die 挤光模英语站 landed positive mold 有肩全压式模具 button die 镶⼊式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中⼼浇⼝式模具 loose detail mold 活零件模具 chill mold 冷硬⽤铸模loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模⽳模具 electroformed mold 电铸成形模 multi-gate mold 复式浇⼝模具 expander die 扩径模 offswt bending die 双折冷弯模具 extrusion die 挤出模palletizing die 叠层模 family mold 反套制品模具 plaster mold ⽯膏模 blank through dies 漏件式落料模 porous mold 通⽓性模具 duplicated cavity plate 复板模 positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold ⽯膏铸模 protable mold ⼿提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模 lancing die 切⼝模 raising(embossing)压花起伏成形 re-entrant mold 倒⾓式模具 sectional die 拼合模 runless injection mold ⽆流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具 shaper 定型模套 single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模 split mold 双并式模具 sprueless mold ⽆注道残料模具 squeezing die 挤压模 stretch form die 拉伸成形模 sweeping mold 平刮铸模 swing die 振动模具 three plates mold 三⽚式模具 trimming die 切边模 unit mold 单元式模具 universal mold 通⽤模具 unscrewing mold 退扣式模具 yoke type die 轭型模 accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻 compacting molding 粉末压出成形 rocking die forging 摇动锻造 compound molding 复合成形 rotary forging 回转锻造 compression molding 压缩成形 rotational molding 离⼼成形 dip mold 浸渍成形rubber molding 橡胶成形 encapsulation molding 注⼊成形 sand mold casting 砂模铸造 extrusion molding 挤出成形 shell casting 壳模铸造 foam forming 发泡成形 sinter forging 烧结锻造 forging roll 轧锻 six sides forging 六⾯锻造 gravity casting 重⼒铸造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting ⾼压铸造 hot chamber die casting 热室压铸 swaging 挤锻 hot forging 热锻 transfer molding 转送成形 injection molding 射出成形 warm forging 温锻 investment casting 精密铸造 matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 低压铸造 lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模 bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具 button die 镶⼊式圆形凹模 loading shoe mold 料套式模具center-gated mold 中⼼浇⼝式模具 loose detail mold 活零件模具 chill mold 冷硬⽤铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模⽳模具 electroformed mold 电铸成形模 multi-gate mold 复式浇⼝模具 expander die 扩径模 offswt bending die 双折冷弯模具 extrusion die 挤出模 palletizing die 迭层模 family mold 反套制品模具 plaster mold ⽯膏模 blank through dies 漏件式落料模 porous mold 通⽓性模具 duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold ⽯膏铸模 protable mold ⼿提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模 lancing die 切⼝模 raising(embossing) 压花起伏成形 re-entrant mold 倒⾓式模具 sectional die 拼合模 runless injection mold ⽆流道冷料模具 sectional die 对合模具 segment mold 组合模 semi-positive mold 半全压式模具 shaper 定型模套 single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold ⽆注道残料模具 squeezing die 挤压模 stretch form die 拉伸成形模 sweeping mold 平刮铸模 swing die 振动模具injection mold 注塑模 rubber molding 橡胶成形 hot chamber die casting 热室压铸 sand mold casting 砂模铸造 extrusion mold 挤出模 multi-cavity mold 多模⽳模具 palletizing die 叠层模 plaster mold ⽯膏模 three plates mold 三板模 plain die 简易模pierce die 冲孔模 forming die 成型模 progressive die 连续模 gang dies 复合模 shearing die 剪边模 riveting die 铆合模compre sion molding 压缩成型 flash mold 溢流式模具 plsitive mold 挤压式模具 split mold 分割式模具 cavity 型控母模 core 模⼼公模 runner system浇道系统 sprue/cold material trap 浇道/冷料井 sprue puller 拉杆 runner design 流道设计 main runner 主流道 secondary runner 次流道 gate design 浇⼝设计 submarine gate 潜伏浇⼝ tunnel gate 隧道式浇⼝ pinpoint gate 点浇⼝fan gate 扇形浇⼝ side gate 侧浇⼝ edge gate 侧缘浇⼝ tab gate 搭接浇⼝ film gate 薄膜浇⼝ flash gate 闸门浇⼝ slit gate 缝隙浇⼝ dish gate 盘形浇⼝ diaphragm gate 隔膜浇⼝ ring gate 环形浇⼝ Runner less ⽆浇道 (sprue less) ⽆射料管⽅式 long nozzle 延长喷嘴⽅式 sprue 浇⼝;溶渣 insulated runner/hot runner 热浇道 runner plat 浇道模块 valve gate阀门浇⼝ slag well 冷料井 cold slag 冷料渣 sprue gate 射料浇⼝，直浇⼝ nozzle 射嘴 sprue lock pin 料头钩销(拉料杆)注塑缺陷：flash 飞边 warpage 翘曲 air trap 积风 blush 发⾚ flow line 流痕 splay 银纹 short shot 短射 sink mark 缩痕 streak 条纹 void 缩孔 weld line 熔接线 gas mark 烧焦 cold slug 冷斑 delamination 起⽪ burr ⽑刺 flaw/scratch 刮伤 gloss 光泽 glazing 光滑surface check 表⾯裂痕 hesitation 迟滞注塑⼯艺:molding conditions 成型条件 drying 烘⼲ barrel temperature 料筒温度 melt temperature 熔化温度 mold temperature 模具温度injection pressure 注塑压⼒ back pressure 背压 injection speed 注塑速度 screw speed 螺杆转速 tensile strength 抗拉强度tensile elongation 延伸率 flexural modulus 弯曲模数 flexural strength 抗弯强度 shrinkage 收缩率 regrind usage 次料使⽤机械设备:lathe车床 planer |刨床 miller 铣床 grinder 磨床 driller 钻床 linear cutting 线切割 electrical sparkle 电⽕花 welder 电焊机punching machine 冲床 robot机械⼿ common equipment常⽤设备 EDM=Electron Discharge Machining 放电加⼯ 3D coordinate measurement 三次元量床 boring machine 搪孔机 milling machine 铣床 contouring machine 轮廓锯床 copy grinding machine 仿形磨床 cylindrical grinding machine 外圆磨床 die spotting machine 合模机 engraving machine 雕刻机engraving E.D.M. 雕模放置加⼯机 form grinding machine 成形磨床 graphite machine ⽯墨加⼯机 horizontal boring machine 卧式搪孔机 horizontal machine center 卧式加⼯制造中⼼ internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板 inner guiding post内导柱 inner hexagon screw内六⾓螺钉dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等⾼套筒 pin销 lifter guide pin浮升导料销 guide pin 导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw⽌付螺丝 located pin定位销 outer bush外导套 punch冲头insert⼊块(嵌⼊件) deburring punch压⽑边冲⼦ groove punch压线冲⼦ stamped punch字模冲⼦ round punch圆冲⼦ special shape punch异形冲⼦ bending block折⼑ roller滚轴 baffle plate挡块 located block定位块 supporting block for location定位⽀承块 air cushion plate⽓垫板 air-cushion eject-rod⽓垫顶杆 trimming punch切边冲⼦ stiffening rib punch = stinger 加强筋冲⼦ribbon punch压筋冲⼦ reel-stretch punch卷圆压平冲⼦ guide plate定位板 sliding block滑块 sliding dowel block滑块固定块active plate活动板 lower sliding plate下滑块板 upper holder block上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板 guide pad导料块模具述语⼀、⼊⽔：gate进⼊位： gate location ⽔⼝形式：gate type ⼤⽔⼝：edge gate 细⽔⼝： pin-point gate ⽔⼝⼤⼩：gate size 转⽔⼝： switching runner/gate 唧嘴⼝径： sprue diameter⼆、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运⽔：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker四、模具零件： mold components 三板模：3-plate mold ⼆板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader ⽔⼝司:bush 垃圾钉：stop pin 隔⽚：buffle 弹⼸柱：spring rod 弹⼸:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销⼦：dowel pin 波⼦弹⼸：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar ⽓阀：valves 斜导边：angle pin 术语：terms 承压平⾯平衡：parting surface support balance 模排⽓：parting line venting 回针碰料位：return pin and cavity interference 模总⾼超出啤机规格：mold base shut hight 顶针碰运⽔：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原⾝出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert ⾏位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 不准⽤镶件： Do not use (core/cavity) insert ⽤铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹⼸压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrodAabrasion n. 磨损 mósǔn abrasion resistance n. 耐磨损性 nài mósǔn xìng abrasive n. 磨料 móliào accelerator n. 促进剂 cùjìnjìaccuracy n. 准确性 zhǔnquèxìng acrylic n. 丙烯酸 bǐngxīsuān，压克⼒ yākelì additive n. 添加剂 tiānjiājì adhere v. 黏附niánfù adhesion n. 黏合 niánhé adhesive n. 胶粘剂 jiāozhānjì air entrapment n. 困⽓ kùnqì anneal v. 退⽕ tùihuǒ assemble v.总成 zǒngchéngBbarrel n. 机筒 jītǒng，料筒 liàotǒng blow molding n. 吹塑成型 chūisù chéngxíng blow molding machine n. 吹塑机 chūisùjībrittle adj. 脆性 cùixìng bubble n. ⽓泡 qìpào by-product n. 副产品 fùchǎnpǐnCcalendering n. 压延 yāyán carbon steel n. 碳素钢 tànsù gāng casting n. 铸造 zhùzào catalyst n. 催化剂 cūihuàjì cavity n. 型腔xíngqiāng chemical resistance n. 耐化学腐蚀性 nài huàxué fǔshí xìng chip v. 削 xiāo，凿 záo clamping force n. 锁模⼒suǒmólì clamping tonnage n. 锁模吨位 suǒmó dūnwèi computer aided design (CAD) n. 电脑辅助设计 diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造 diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制 diànnǎo shùzì kòngzhì ceramic n. 陶瓷 táocí cold rolled steel n. 冷轧圆钢 lěng zháyuán gāng cold runner n. 冷流道 lěngliúdào colorant n. 着⾊剂 zhuósèjì composite n. 复合材料 fùhé cáiliào compression strength n. 抗压强度 kàngyā qiángdùcooling channel/circuit n. 冷却管道 lěngquè guǎndào cooling rate n. 冷却速率 lěngquè sùlǜ core n. 型芯 xíngxīn，模芯móxīn corrosion n. 腐蚀 fǔshí corrosion resistance n. 耐腐蚀性 nài fǔshí xìng cure v. 固化 gùhuà custom adj. 定制 dìngzhìcycle time n. 循环时间 xúnhuán shíjiānDdegassing n. 排⽓ páiqì density n. 密度 mìdù deform v. 变形 biànxíng die n. 冲模 chòngmó die casting n. 压铸 yāzhù，模铸mózhù dimension n. 尺⼨ chǐcùn dimensional tolerance n. 尺⼨公差 chǐcùn gōngchà distort v. 扭曲 niǔqū draft angle n. 拨模斜度 bōmó xiédù dwell time n. 驻留时间 zhùliú shíjiān dye n. 染料 ránliàoEejector mark n. 顶出痕迹 dǐngchū hénjì ejection pin n. 顶出杆 dǐngchū gān，推顶锁 tūidǐng suǒ，脱模锁 tuōmó suǒ ejection plate n. 推顶板 tūidǐng bǎn，脱模板 tuōmó bǎn ejection rod n. 脱模板拉杆 tuōmó bǎn lāgān elastomer n. 弹性体 tánxìngtǐelectrical discharge machining (EDM) n. 电⽕花加⼯ diànhuǒhuā jiāgōng epoxy n. 环氧树脂 huányǎngshùzhī extruder n. 挤出机 jǐchūjī extrusion n. 挤出 jǐchū，挤塑 jǐsùFfabricate v. 制造 zhìzào fiber n. 纤维 xiānwéi fiberglass n. 玻璃纤维 bōli xiānwéi fiber reinforcement n. 纤维增强 xiānwéizēngqiáng film n. 薄膜 báomó fire retardant n. 阻燃剂 zǔránjì flash n. 溢料 yìliào flow mark n. 流痕 liúhén flow rate n. 流动速率liúdòng sùlǜ fluorescent adj. 荧光 yíngguāng fluorescent brightener n. 荧光增⽩剂 yíngguāng zēngbáijì foam n. 泡沫 pàomòfuse v. 熔合 rónghéGgas assisted injection molding n. ⽓辅注射成型 qìfǔ zhùshè chéngxíng gate n. 浇⼝ jiāokǒu gate mark n. 浇⼝痕 jiāokǒu hén gear n. 齿轮 chǐlún grinder n. 研磨机 yánmójī，磨床 móchuángHheat conduction n. 热传导 rè chuándào heater band n. 加热圈 jiārè quān heat treatment n. 热处理 rè chǔlǐ high density polyethylene (HDPE) n. ⾼密度聚⼄烯 gāo mìdù jùyǐxī high impact plastic n. ⾼抗冲塑料 gāo kàngchòng sùliào high impact polystyrene n. ⾼抗冲聚苯⼄烯 gāo kàngchòng jùběnyǐxī hobbing n. 滚铣 gǔnxǐ，挤压制模 jǐyā zhìmó，切压制模 qiēyāzhìmó holding n. 保压 bǎoyā hot runner n. 热流道 rè liúdàoIimpact strength n. 冲击强度 chòngjī qiángdù injection n. 注射 zhùshè，注塑 zhùsù injection molding n. 注塑成型 zhùsùchéngxíng injection molding machine n. 注塑机 zhùsùjī injection pressure n. 注塑压⼒ zhùsù yālì insulated runner n. 绝热流道 juérè liúdào，保温流道 bǎowēn liúdào insulation layer n. 绝热层 juérè céng internally heated runner n. 内加热流道 nèijiārè liúdào internal void n. 内部空腔 nèibù kōngqiāngJjoint n. 接头 jiētóu，连接 liánjiēLlaser n. 激光 jīguāng laser cutter n. 激光切割机 jīguāng qiēgējī lathe n. 车床 chēchuáng locating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚⼄烯 dī mìdù jùyǐxīM。
模具英语
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;Torpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure 开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance。
模具标件专业英语词汇
模具标件专业英语词汇一、模具（Mold）相关基础词汇。
1. Mold [məʊld] - 名词，模具；也可作动词，塑造，浇铸。
- 例句：This is a new type of injection mold.（这是一种新型的注塑模具。
）2. Die [daɪ] - 名词，冲模，钢模（在冲压工艺中使用）- 例句：The die is used for stamping metal sheets.（这个冲模用于冲压金属薄板。
）3. Cavity ['kævəti] - 名词，型腔；洞，凹处。
- 发音：['kævəti]- 例句：The cavity of the mold should be polished carefully.（模具的型腔应该仔细抛光。
）4. Core [kɔː(r)] - 名词，型芯；核心。
- 例句：The core is an important part of the mold.（型芯是模具的一个重要部分。
）二、模具标件（Standard Mold Components）词汇。
1. Guide Pin ['ɡaɪ d pɪn] - 名词，导柱。
- 例句：The guide pin helps to align the two parts of the mold.（导柱有助于使模具的两个部分对齐。
）2. Guide Bushing ['ɡaɪ d 'bʊʃɪŋ] - 名词，导套。
- 例句：The guide bushing is used in combination with the guide pin.（导套与导柱配合使用。
）3. Ejector Pin [i'dʒektə pɪn] - 名词，顶针。
- 例句：The ejector pin is used to push the finished product out of the mold.（顶针用于将成品从模具中顶出。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding挤出成形shell casting 壳模铸造foam forming发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模1split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头2impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料销spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板3模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 内卡钳inside micrometer 内分厘卡interferometer 干涉仪leveling block 平台limit gauge 限规micrometer 测微计mil 千分之一吋monometer 压力计morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺stylus 触针telescopic gauge 伸缩性量规working gauge 工作量规模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板4hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀5plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔ampere 电流安培angle welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲cascade 阶叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属filler rod 焊条fillet weld 填角焊接gas shield 气体遮蔽groove welding 起槽熔接hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIGb 熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接skip welding process 跳焊法spark 火花spot welding 点焊接stitch welding 针角焊接stud arc welding 电弧焊接under laying 下部焊层void 焊接空隙weld flow mark 焊接流痕6weld flush 焊缝凸起weld line 焊接纹weld mark 焊接痕weld penetration 熔接透入weld zone 焊接区welding 焊接welding bead 焊接泡welding direction 焊接方向welding distortion 焊接变形welding flux 焊剂welding ground 电熔接地welding interval 焊接周期welding stress 熔接应变welding torch 熔接气炬射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动模板foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑胶片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑胶原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑胶epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EV A ethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene 发泡聚苯乙烯EPS fiber reinforcement 纤维强化热固性/纤维强化复合材料7high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷8sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁鎚hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手计算机关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 总线CAD 计算机辅助设计CAE 计算机辅助工程分析CAM 计算机辅助制造9cassette卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 计算机copy 复制cursor 游标curve modeling 曲面模拟database 数据库design 设计digitizing 数字化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬件honeycomb 蜂巢interface 界面know how 秘诀laser printer 雷射打印机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模块monitor 荧幕mouse 鼠标need 需求network 网络new version 新版on line 上线中option 选择PC 个人计算机plotter 绘图机program 程序scanning 扫描simulation 模拟software 软件solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking 铆合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工10seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边铆接staking 铆固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落鎚brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat 铆合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻鎚cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距11pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆栈拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 后角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze 钨青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模12all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落鎚bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工13joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining 超音波加工up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验falling ball impact test 落球冲击试验fatigue test 疲劳试验ferrite 纯铁体gantt chart 甘特图heat cycle test 热循环试验histogram 柱状图hot bend test 热弯试验izod impact test 埃左德冲击试验loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验normal distribution 常态分配ozone resistance test 抗臭氧试验pareto diagram 柏拉图peeling test 剥离试验pinhole test 针孔试验机rattler test 磨耗试验rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验sampling inspection 抽样检查scratch hardness 抗刮硬度shore hardness 萧氏硬度spiral flow test 螺旋流动试验surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机tensile impact test 拉伸冲击试验tensile strength 抗拉强度tension test 张力试验thermal shock test 冷热剧变试验torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验warpage test 翘曲试验weatherometer 人工老化试验机weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮Al2O3 氧化铝balance 平衡bond 结合borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt 循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目parameter 参数resinoid grinding wheel 半树脂型砂轮slitting 切缝量vitrified 陶瓷的wheel 旋转机械设计及周边其他用语14assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重覆载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割业务与贸易关连用语accept order 接受订货account 账户after service 售后服务amendment 修正annual sales 年销售额at sight 见票即付balance 余额bank draft 汇票bargain goods 廉价品batch 批次bid 出价bid sales 投标买卖bill of landing 提单bills receivable 应收票据brand 品牌bulk cargo 散装货business transaction 商业交易buyer 买方carbon copy 打字副本cargo collection 揽货carton 纸箱cash in advance 预付现金catalogue 型录cheque 支票CLF 运费保险费在内价格claim 索赔clearance goods 清仓品commision 佣金commission 批发商complain 抱怨container 货柜correspondence bank 往来银行cost 成本cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣15discount on draft 贴现documentary draft 跟单汇票down payment 订金enclosure 附件endorsement 背书enquete 调查exhibition 展览会export 出口factory visiy 工厂参观favourable price 合宜价格foreign exchange 外汇free on board 船上交货价idea price 希望价格import 进口Japanese Industrial 日本工业规格invoice 发票L/C 信用状margin 利润market 市价net weight 净重no payment 拒绝付款odd item 零头offer 报价open account 交互计算order 订单over looked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格price decending 减价price rising 涨价procurement 采办prompt delivery 实时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣reference 查询remittance 汇款repeat order 追加订货request letter 请求函rumor 风评second hand goods 二手货shipper 货主shipping 装船shipping mark麦头shipment 出货sold out 卖完sole agent 总代理商special discount 特别折扣specification 规格sample order 指样订货standing 信用情形storage charge 仓租subcontract 外包subject to final confirmation 有待确认之报价supplier 供应商T/T 电汇tie-in sale 搭售trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头(国立台湾大学机械研究院)16。