MERCKMILLIPORE默克密理博Milli-QIntegral实验室纯水超纯水系统

合集下载

Millipore(密理博)Milli-Q超纯水机维护指导

更换过滤柱1) 将机器调节为STANDBY”状态，卸下终端过滤器，打开取水开关，将系统卸压，待确认机器无水流出后，关闭取水开关。

2) 向左轻扳机器正面蓝色门的锁片（上下各一片），打开蓝门，将“QUANTUM”柱取出，再将机器右侧白色“QGARD”柱上端盖子打开，取下金属锁片，即可取出“QGARD”柱。

3) 将新的“QGARD”柱装到机器上，注意机器上的金属杆要对准柱子上的孔，向左推紧后，将金属锁片锁在金属杆的卡槽内，扣上顶端盖子；再将新的“QUANTUM”柱装入蓝门内，稍用力向里推紧，关闭蓝门，需听到两个锁片“嗒”的声音后，才能确认柱子已装到位。

4) 将附件中的管子接头拧入取水柄中，接上软管引到水槽里；打开取水开关，系统会自动进入5分钟的排空气程序中，5分钟结束后，系统会自动进入“OPERATE”状态。

5) 卸下管子接头及软管，装上终端过滤器；注意过滤器上的空气帽不要拧紧，打开取水开关，待水从空气帽中流出后，再拧紧空气帽。

6) 柱子更换完毕，将系统在“OPERATE”状态下过12小时以上，便可正常使用。

如何判断柱子是否寿命已到1) 当系统已使用一段时间后，首先检查，当取水开关打到循环位置时，查看显示屏的电阻率由初始值升到18.2MΩ·cm时，需要多少时间，正常情况不会超过1分钟，或在产水过程中，出现电阻率下降(不稳定)的情况时，均证明柱子的寿命已快到期了。

2) 如果出现产水流量明显下降(正常每分钟为1-1.5L左右)，在确认系统中确实无空气的前提下，多数是因为终端过滤器已堵塞而所至。

3) 为确保系统能正常运转，以及最经济的使用过滤材料(过滤柱等)，建议在更换耗材时，最好统一一起更换。

MILLI-Q 超纯水机使用技巧1) 工作中有时因为疏忽大意，会忘将进水水桶中加水，会使机器进空气，此时机器显示屏上会显示"AIR PURGE"，这时，只需打开取水开关（开到产水位置），显示屏会显示"AIR PURGE 5MN"，待5分钟后，显示屏会显示"CLOSE THE VALVE"，此时只需关闭取水开关，机器就可以正常工作了。

MERCK MILLIPORE默克密理博Aquelix5实验室纯水机

MERCK MILLIPORE 默克密理博Aquelix 5实验室纯水机MERCK MILLIPORE 默克密理博Aquelix5实验室纯水机是一款专为中小型实验室量身定制的实验室高纯水制备系统，系统采用Millipore专利的Elix电流去离子技术，结合优良的预处理和先进的反渗透技术，以便捷、经济的方式生产高品质的二级高纯水。

Millipore密理博Aquelix5实验室纯水机以自来水为进水直接生产高纯水，产水适用于微生物、光谱、色谱等多种实验需求。

○ 针对中小型实验室用水量小，并对水质有一定要求的客户○ 解决中小型实验室获取高纯水难的问题 (蒸馏水器不安全且维护繁琐、运行费用高，桶装水水质较差且无法在线监控)○ 面对空间有限的实验室，只需A3纸大小的面积，即可安装○ 维护简单：Aquelix整套系统只有一套耗材，更换简单，只需30秒钟即可完成○ 运行、维护费用低高品质纯水，源自卓越的Elix技术MERCK MILLIPORE 默克密理博Aquelix5实验室纯水机所采用专利的Elix抗结垢连续电流去离子技术，与您目前正在使用的其它纯化方法(蒸馏、国产反渗透/去离子系统、瓶装水)相比，具有更多优势：品质无忧Elix 技术确保持续稳定地生产出高品质纯水优化流程：取水口处可选择安装Millipak®0.22μm终端过滤器，有效去除微生物清晰完整的系统参数显示(水质、报警/提示)运行成本低Elix技术提供持续的离子交换树脂再生，无需更换耗电量低：系统用电仅为传统蒸馏装置的1/180进水耗水量低：仅为蒸馏装置的1/5使用便捷根据需求，最高2升/分钟的流速进行纯水取用耗材更换简单快速，仅需花费几十秒钟维护少：Elix 技术无需强酸强碱或复杂的除垢处理。

* MERCK MILLIPORE 默克密理博Aquelix5实验室纯水机设计用于生产符合欧洲、日本和美国药典要求的纯水(Millipak终端过滤器用来满足微生物指标)。

merck millipore 默克密理博纯水超纯水一体系统明澈D24UV操作手册

11
明澈-D 24 UV
需要的物品
13
物品检查清单安装开始前请核实所有物品是否可用。
o 纯水系统主机 (A) o 用户手册和快速参考指南 (B) o 外部电源 (C) o PROGARD®预处理柱和 Q-GARD®超纯水柱（D） o 储水水箱：30、60 或 100 升（E） o POU 取水器（F） o 包含下述的附件包：管材配件电源
8
2 显示器和小键盘
9
3 Progard® 预处理柱位置
10
4 锁定手柄
11ห้องสมุดไป่ตู้
5 消毒/清洁口
12
6 电源接口
13
7 系统进出水口连接
14
*系统断电时，应将电源与插座断开。
说明系统 ID 和序列号电源适配器* Q-GARD®超纯水柱位置超纯水进出口接口 POU（用水点）取水POU 取水开关取水器终端过滤器
重要提示！
应在干净且干燥的地方安装并操作您的纯水系统。请参考本手册最后部分的环境要求。
您的纯水系统不适于家庭使用。
纯水系统长时间断电会使计时器的电池放电，导致失去时间和日期记录。如果长时间关闭纯水系统，应使用实验室关闭模式请与您的服务代表联系。
经常保存系统的历史记录-每三个月或每半年。参见 Millitrack 文档。
软件选项millitrack软件是通过ajax异步javascript和xml技术开发的一种嵌入式gui图形用户界面软件它能运用tcpip以太网协议通过点到点计算机或直接通过网络连接生成交互式网页
用户手册
明澈™-D 24UV 纯水系统
序言
感谢您购买我们的纯水系统。对于任何疑问或请求，请根据以下联系信息与 Merck Millipore 联系。

默克Milli-Q超纯水解决方案

默克Milli-Q®超纯水解决方案客户至上的超纯水解决方案概览智能。

直观。

让您无忧无虑地工作，最大程度提升实验室工作效率。

创新的人体工程学设计以及强大的纯化树脂，确保优质超纯水源源不断。

不妨了解一下Milli-Q® IQ 7000是如何改变您在实验室中的工作方式的。

功能与优势一览•简单而直观的取水：通过全新的“滚轮”取水，Q-POD®取水手臂让取水变得远更简单精确，毫不费力。

其丰富的取水功能，是实验室日常工作的一大福音。

•大型交互式触摸屏：如同智能手机，只需轻松点击Q-POD®取水臂的交互式触摸屏，即可随心所欲地操作。

•优化的实验室空间：让您的工作场所井井有条！系统设计注重安装整洁和台面干净，告别凌乱的管线。

只需专心与Q-POD®取水臂互动——这款紧凑系统的其余部分可轻松融入实验室环境。

对于多点使用的实验室，最多能够连接4台Q-POD®取水臂。

•卓越的超纯水—始终如一—达到痕量水平：默克Milli-Q® IQ 7000纯水系统结合Jetpore®和IQnano®树脂提供始终如一的微量超纯水。

其纯度之高，彻底消除您在关键实验中的后顾之忧。

同时，通过A10® TOC机载监控功能，可以避免不确定性或结果误读，以及费时费钱的反复分析。

•改善的可持续性：默克的产品设计注重可持续性。

Milli-Q® IQ 7000系统使用了无汞、环保的紫外线氧化灯。

此外，通过“LabClose”模式使系统自动进入“休眠”状态，在您离开实验室时保持系统水质，同时节约能耗。

•高级的可追溯性：高级数据追溯是Milli-Q® IQ 7000的一大特性。

取水事件确保所有取水报告历史记录在案，而每日质量评估为水质提供了长期可追溯性。

当需要进行更深入的分析时，完整历史记录是对所有系统数据的全局归档。

此外，POD-Paks系统和IPAK 预处理柱还带有e-Sure标签，也确保了可追溯性。

默克密理博纯水机的优点

默克密理博纯水机的优点密理博（millipore）公司作为生命科学领域的策略性供应商，为生物科学讨论和生物制药工业供应技术、工具和服务。

2023年4月21日，密理博中国正式对外发布新品—Milli-QIntegral纯水/超纯水一体化系统。

该款纯水系统可以直接以自来水进水，只需经过一台主机，即可得到水质稳定的II级纯水和I级超纯水。

Milli-QIntegral系统结合了Elix、Milli-Q纯水系统的技术和解决方案，生产出带压力的纯水和超纯水，用户可以直接掌握整个水纯化链的水质。

除此之外，应用了可以通过微弱电流不断再生离子交换树脂的Elix技术，胜利降低了Milli-QIntegral超纯水系统的维护和运营成本。

Milli-QIntegral系统可以依据用户的不同需要，每天产纯水或超纯水60~300L不等。

配有两种分体式取水器：Q-POD（取超纯水）和E-POD （取纯水），从点滴取水至2L/min，产水速度可任意调整且操作简便。

用户可以根据不同水质要求选择不同的终端精制器，特地去除热源、核酸酶、细菌、颗粒和有机物。

依据用户的不同需求，密理博纯水机每天可生产60至300升纯洁水或超纯水。

配备两个分体式取水器：取超纯水和取纯水，滴水量取至2L/min，出水速度可任意调整，操作简便。

用户可以依据不同的水质要求选择不同的终端精炼机，以特地去除热源，核酸酶，细菌，颗粒和有机物，分体式取水器使用起来特别便利。

它不仅适用于试验室中的全部玻璃器皿，还供应自动和手动进水方式，系统操作和水质信息（离子和有机污染）显示在主机和饮水机底座的LCD屏幕上，可以在线查看或在线打印。

密理博纯水机结构紧凑，与系统配套的取水器占地面积小，可以安装在试验室的任何地方，例如工作台下方或墙上。

由于它供应了多种敏捷的安装方法和升级选项，因此可以在不同阶段依据用户的试验需求来更改配置。

每个主机可以连接3个取水器，这些取水器可以放置在试验室的不同位置。

MilliporeSigma Milli-Q CLX 7000系列连接水纯化系统用户说明书

®7000 SeriesRobust & Reliable Performancefor Maximum Lab ProductivityYour biomedical laboratory is a busy and demanding environment, with clinical analyzers capable of processing several thousand samples per day. As water is the most frequently used fluidic reagent onboard an analyzer, your choice of water purification system is key to smooth and uninterrupted daily lab operations.The water purification solution must reliably provide your clinical analyzer(s) with consistent water quality that meets CLRW standards of the CLSI®. With the high-throughput Milli-Q® CLX 7000 analyzer feed series, your clinical laboratory benefits from a high-performance and economical water purification solution that fulfills its many critical needs:3Simply log into the MyMilli-Q™ web interface todiscover MyMilli-Q™ Remote Care , our online service and monitoring capability designed to support you in maximizing uptime. This unique service gives you and our support teams access to your Milli-Q ® CLX 7000 system and its data, for quick and precise remote diagnostics as well as repairs. Learn more about thisnew service capability on pages 8 and 9 of this brochure. And because every lab situation is different, our Milli-Q ® Services offering can be customized around your needs:• Before installation, a certified Field Service Engineer will analyze your feed water quality to provide the optimal parameter configuration for your system. This maximizes the performance and reliability of your Milli-Q ® CLX 7000 instrument and associated clinical analyzers.• Choose the Milli-Q ® Service Plan that’s right for your lab—from a single annual Preventive Maintenance Visit with replacement of aging parts, to full system coverage. • Online Contract Management lets you moreefficiently track your water system’s service history and easily schedule maintenance visits.• A range of options lets you customize your service solution. Choices include qualification, calibration and verification services, scheduled consumables shipments, and sanitization.Best-in-class Milli-Q ®Services,now supported by MyMilli-Q™ Remote CareBecause the reliability of biomedical laboratories is critical to patients and doctors alike, we offer an unprecedented level of service with the Milli-Q ® CLX 7000 Series.Trust in Pure Experience & ExpertiseWe are a partner you can count on. As one of the top three R&D investors in the Life Science Toolsindustry, we have a long history of strong partnerships with both biomedical laboratories and major clinical analyzer manufacturers. This valuable experience has enabled us to develop our expertise concerning end-user applications, such as biology, biochemistry, microbiology and immunology, and to design top-quality water purification solutions dedicated to feeding clinical analyzers.The Milli-Q ® CLX 7000 Series is manufactured in an ISO ® 9001- and ISO ® 14001-registered site. Additionally, to ensure efficiency and safety ofoperation, systems are CE-, cULus-, and FCC-certified. Furthermore, to reduce environmental impact, the Milli-Q ® CLX 7000 Series follows European Restriction of Hazardous Substances (RoHS) and Waste Electricaland Electronic Equipment (WEEE) directives.Contact your local Merck office for information about the service offer available for your facility, or visit /milli-qservices4® technology puriﬁcation stepsElix ® module: Our unique technology is based on anion-permeable and cation-permeable membranes and high-quality, ion-exchange resin.Water produced by the Elix ® module enters the reservoir with resistivity greater than 5 MΩ·cm @ 25 °C (typically up to 15 MΩ·cm @ 25 °C).*The Milli-Q ® CLX 7000 Series relies on complementary water purification techniques, including state-of-the-art Elix ® electrodeionization (EDI) technology, to ensure production of consistently high quality water meets CLRW standards – at low and predictable running costs.In the Milli-Q ® CLX 7000 Series, potable tap water is first treated with a Progard ® pack and purified by reverse osmosis (RO) to remove up to 99% of contaminants. The resulting RO permeate water then enters the Elix ®Bacteria and their by-products interfere with chemistry assays and enzyme immunoassays, typically leading to unstable analyzer calibrations, high absorbance of blanks, reference drifts, and errors on mean patient values.In the Milli-Q ® CLX 7000 Series, UV lamp sanitization occurs at three stages:• During water production , a 254 nm bactericidal UV lamp inactivates bacteria.• In the tank , a UV lamp (ASM, Automatic Sanitization Module) regularly irradiates stored water and the tank walls, preventing bacterial growth and the formation of biofilm.* When CO dissolved in feed water is less than 30 ppm.5Optimize water consumption with an environmentally responsible system containing E.R.A.® technologyMilli-RX™ system(1992)Elix system (2003) with RO recovery loop Today’s Mili-Q CLX 7000Series system with E.R.A. technology10000m 900080007000600050004000300020001000WASTE (m )CLRW (m )Over the last 25 years, we have dramatically reduced water purification system water consumption, enabling laboratories to save up toseveral thousand dollars per year on tap water expenses . The graph shows water consumption and the split between CLRW produced and reject water for three of our water purification systems over a seven-year period (production of 1000 L/day of CLRW-quality water, 312 days per year).The Milli-Q ® CLX 7000 Series incorporates our E.R.A.® (Evolutive Reject Adjustment) technology — providing users with even greater savings.With its innovative and efficient reverse osmosis (RO) recovery loop, the Milli-Q ® CLX 7000 Series optimizes water consumption by recycling part of the waterrejected to the drain, thus reducing water waste and also extending RO cartridge and Progard ® pack lifetimes.Furthermore, depending on the feed water qualityanalysis, the Milli-Q ® CLX 7000 Series will calculate the best water recovery and will automatically optimize water consumption by means of motorized valves.No matter what the feed water temperature, inlet pressure, or conductivity may be, E.R.A.®technology’s automated valves ensure that the Milli-Q ® CLX 7000 Series flow rate and water recovery remain constant.* Users no longer need to manually adjust valves to maintain production flow rate and protect RO cartridge lifetime.These latest RO technologies illustrate our dedication to developing environmentally responsible waterpurification solutions to reduce tap water and system consumables use. The solutions reduce maintenance time, as well as the risk of human error — letting users save money on system operation, and also enjoy peace of mind with higher reliability, and optimized water purification system/analyzer uptime.* Please refer to Feed Water Requirements in the Specifications Table.6User-friendly system interface with all relevant information at a glanceWith its large, innovative touchscreen, the system is designed for intuitive operation, with all information available at a glance in a dashboard format. Nine different languages are available for greater convenience. Navigating and interacting with your water purification system has never been easier!... where a wizard will guide you through the maintenance procedure with easy, step-by-step instructions. You don’t need to be an expert to perform regular maintenance on your system!Clear, visible status of all consumables Notification zone for alerts and alarmsLarge display shows water qualities and storage volumeSystem status zone7An easy-to-use,low-maintenance systemA mobile, customizable systemLow maintenance saves time and increases profitability• Robust and patented Elix ® technology ensuresconsistent pure water, as well as low and predictable running costs – regardless of your feed water quality.* No maintenance is required for the Elix ® module.• An ergonomic and patented pack-locking system lets you change packs easily and quickly.• RFID technology prevents insertion of an incorrect purification cartridge in Milli-Q ® CLX 7000 systems, and also ensures automatic traceability of pack use and replacement, saving time for the user.• Automatic self-maintenance functions significantly reduce tap water use and increase cartridge lifetime: –The Progard ® pretreatment pack incorporatesseveral purification media in just one consumable to protect the RO membrane from particles, free chlorine, and scaling. Maintenance is easier and quicker with only one pack to change! –The system’s flush mode and cleaning cycles keep the RO membrane in top operating condition.Never before has it been so easy—or so time-saving—to use and maintain your water purificationsystem.Optimal use of lab spaceThe Milli-Q ® CLX 7000 Series is compact, quiet, and mounted on wheels with brakes, so it can be placed wherever it’s convenient — and moved to another location as the lab configuration grows or evolves.Customizable systems to fit your specific requirementsA number of options and accessories are available for the Milli-Q ® CLX 7000 Series to fit your specific requirements and to improve water quality monitoring:• An online TOC (Total OrganicCarbon) monitor allows verification that the TOC level of system water is below 500 ppb as required for CLRW quality. This avoids the need for duplicate assays or repeated analyzer calibrations. • Degassing option provides asolution for feed water that is highly contaminated with gases, such as a CO 2 concentration above 30 ppm.• RO regeneration tool , for use whenfeed water quality is poor, provides additional RO membrane cleaning, and completes the action of the Progard ® Autoclean pack.• Sanitary sampling valve for safe and reliable water sampling for microbiological analysis.• Water sensor(s) and alarm output(s) also can be easily added to your Milli-Q ®CLX 7000 system.* P lease refer to Feed Water Requirements in the Specifications Table.An ergonomic and patented pack-locking system.245 13 67What can MyMilli-Q™ Remote Care help you to achieve?• Assure productivity 24/7. Access real-time system information, water quality data and much more from anywhere at any time for 24/7 confidence in your lab’s performance.• Save time. In the event you need support, your interaction with Milli-Q® Services is streamlinedas MyMilli-Q™ Remote Care provides our service organization a secure and direct view of your system information. Our service teams can remotely diagnose and potentially repair your system, avoiding the need to wait for a service visit.• Maximize uptime. Receive notification of alertsand alarms (by email or SMS) allowing you to promptly and remotely manage your system, either independently or with our remote assistance.• Easier data traceability & accreditation. Audit preparation and lab accreditation have never been so effortless as data are automatically saved and can be easily accessed, searched and retrieved. Choose to download a standard Quality Report, or to create your own tailored reports.Connect to Peace of Mind Milli-Q® Services presents MyMilli-Q™ Remote Care, an onlineservice that simplifies the management of your Milli-Q® CLX7000 water purification system.1 Quickly view all system details.2E asily share water quality and system information with your analyzer supplier’sservice hotline.† CAP , College of American Pathologists9A water purification system that facilitates accreditation.Water used to feed an analyzer is a critical reagent. Its quality must be documented forbiomedical laboratories seeking accreditation (or reaccreditation) to the ISO 15189:2012 standard supported by CAP † 15189SM accreditation.To facilitate compliance with worldwide regulatory organization guidelines, Milli-Q ® CLX 7000 systems allow for full monitoring capabilities as well as automatic e-record archiving both:• Directly in the system — data are retrievable by USB key or via your lab’s intranet connection.• In the cloud when MyMilli-Q™ Remote Care is activated.E-record archiving supports traceability of all water-related daily operations, measurements and events. It saves time and is less expensive to manage versus paper documentation, as it removes the need for daily checks of the water purification system, hand-recording of parameters in a lab book, and physically archiving years of paper data.Now, with the user-friendly MyMilli-Q™ web interface and MyMilli-Q™ Remote Care service capability, data management is even moresimplified. Your system and water data are readily accessible and rapidly searchable, graphable and reportable — from anywhere at any time.An interactive Event Traceability tool lets you view events by type and over the timeline you specify. View past events (alarms, alerts, consumable replacements, service visits, custom events) and plan for future systemmaintenance. Click on any event and its details are displayed in the blue banner above the timeline. In this example, aProgard ® cartridge was replacedby J.SMITH on Aug 19, 2019.Water quality parameters (resistivity, temperature, TOC) are graphed over the timeline of your choice and can be easily downloaded.The system automatically stores a fully traceable—and easily retrievable—record of service history. In addition to archiving data, MyMilli-Q™ online tool lets you streamline contract management. You’ll be able to schedule maintenance visits, manage consumable deliveries and renew your service contracts, all online.Milli-Q® CLX 7000 Series Water Purification Process1. Inlet Valve2. Progard® Pretreatment Pack3. Conductivity Cell4. RO Pump5. Pressure Sensor6. RO Cartridge7. Twin Motorized Valve –RO Recirculation 8. RO Recirculation Loop9. Temperature Sensor10. Flow Sensor11. 3-Way AutomaticRinsing Valve12. Elix® Module13. Resistivity Cell14. UV Lamp (254 nm)15. Vent Filter16. Sanitary Overflow Sensor17. Automatic SanitizationModule (ASM)18. Distribution Pump19. Emergency Back Up –Quick Connector20. Q-Gard® Polishing Pack21. Opticap® Filter (0.22 μm)22. Sampling Valve23. Automatic Loop Rinsing Valve24. Back Pressure Regulator25. Recirculation Loop Valve26. TOC Monitor (Option)27. Degassing Unit (Option)Milli-Q® CLX 7000 Series SpecificationsThe Clinical Laboratory Reagent Water (CLRW) Quality Standard, defined by the CLSI®Resistivity> 10 MΩ.cm @ 25 °C Total organic carbon (TOC)< 500 ppbBacteria< 10 CFU/mL Filtration0.22 μmMilli-Q® CLX 7000 Series PerformanceMilli-Q® CLX 7040Milli-Q® CLX 7080Milli-Q® CLX 7120Milli-Q® CLX 7150 Make-up flow rate to reservoir*40 L/h (10.6 gal/h)80 L/h (21.1 gal/h)120 L/h (31.7 gal/h)150 L/h (39.6 gal/h) Make-up resistivity> 5 MΩ.cm @ 25 °C (10-15 MΩ.cm @ 25 °C typically)Built-in reservoir volume (net volume)90 L90 L140 L140 LDistribution flow rate to analyzers 4 L/minDistribution pressure to analyzers Adjustable: 0.9 up to 2.1 bar†Water Quality Distributed to AnalyzersResistivity> 15 MΩ.cm @ 25 °C Total organic carbon (TOC)Typically < 30 ppb Bacteria Typically < 1 CFU/mL Dissolved silica< 0.05 mg/L* Nominal flow rates ± 10% between 10 and 35 °C. Additional deviation of -3% per °C from 10 °C to 5 °C.† With a distribution loop length of 20 m.Technical Appendix10*Subject to subscription. Please contact your local Merck office for information about the service offer available for your facility.Dimensions and WeightsDimensions (H x W x D)1255 x 543 x 797 mm(49.4 x 21.4 x 31.4 in)1255 x 543 x 797 mm(49.4 x 21.4 x 31.4 in)1255 x 543 x 947 mm(49.4 x 21.4 x 37.3 in)1255 x 543 x 947 mm(49.4 x 21.4 x 37.3 in)Net weight (shipping box)134 kg (295.4 lb)143 kg (315.3 lb)155 kg (341.7 lb)167 kg (368.2 lb) Operating weight222 kg (489.4 lb)234 kg (515.9 lb)303 kg (668 lb)318 kg (701.1 lb)Feed Water RequirementsPressure 2 – 6 barFlow rate> 10 L/min at 2 barTap water connection¾ in. Gaz MFeed water type PotableTemperature 5 – 35 °CConductivity10 – 2000 μS/cm at 25 °C pH 4 – 10Total hardness (as CaCO3)< 300 ppmCO2< 30 ppmSilica< 30 ppmMerck KGaAFrankfurter Strasse 25064293 Darmstadt, Germany /labwater。

默克密理博纯水机的优点

默克密理博纯水机的优点默克密理博是一家领先的水处理技术公司，并以其创新的纯水处理技术而著称。

默克密理博纯水机作为该公司的旗舰产品，拥有许多优点使其成为用户的首选。

下面是默克密理博纯水机的几个优点。

1. 高效的净水能力默克密理博纯水机采用先进的反渗透技术，能够高效地除去水中的杂质、细菌和有害物质。

其滤芯由精确的膜片组成，可以有效地去除其他水处理方法无法消除的微小颗粒和溶解物。

净水能力高，确保用户获得纯净、安全的饮用水和使用水。

2. 多种过滤功能默克密理博纯水机拥有多种过滤功能，可以根据不同需求满足用户的净水要求。

除了基本的颗粒和溶解物过滤外，还可以选择额外的滤芯，用于去除重金属、有机物和余氯等。

这种多功能的设计让用户在使用过程中更加方便，并能根据实际需要进行选择。

3. 智能化控制和用户友好界面默克密理博纯水机具有智能化控制系统，能够自动监测水质和滤芯寿命，并根据结果进行相应的调整。

用户只需简单设置一次，系统就能自动进行工作，大大减轻用户的操作负担。

此外，纯水机还具有用户友好的界面，可以清晰显示水质信息和滤芯状态，方便用户随时了解净水情况。

4. 节省资源和环保默克密理博纯水机采用了高效的净水技术，能够通过滤芯的再生和重复使用来节约水资源。

此外，其纯水机废液的分离技术可将废液回收，减少水的浪费并保护环境。

默克密理博一直致力于绿色环保，通过优化设计和高效的净水技术，使得纯水机在资源利用和环境保护方面更加出色。

5. 高品质和长久使用寿命默克密理博作为一家知名品牌，以其高品质和可靠性而闻名。

默克密理博纯水机使用优质原材料，以确保产品的可靠性和耐用性。

其设计和制造过程严格符合国际标准，并经过多次严格测试，保证产品的质量和使用寿命。

用户可以放心购买并长期使用默克密理博纯水机，而无需担心质量问题。

6. 安装和维护简便默克密理博纯水机的安装和维护非常简便。

产品提供详细的安装手册和使用说明书，用户可以根据说明进行简单的安装设置。

Milli-Q Synthesis 超纯水系统中文使用说明书

Milli-Q Synthesis 超纯水系统中文使用说明书Milli-Q Synthesis超强组合型详细说明：IVF等极为困难的特殊培养以及分子生物学实验专用Milli-Q Synthesis系结合Gradient所采用的短波UV灯(185nm)以及Biocel所采用的5,000分子量的UF 膜，其产水的TOC值可在5ppb以下(当进水的TOC值低于50ppb)，热源则低于0.001EU/ml的新型超纯水装置。

本系统特别适用在容易受到水质影响的IVF或是DNA、RNA等分子生物学实验。

当然，Milli-Q Synthesis 的产水也可使用在需高灵敏度的HPLC检测上。

功能◆TOC数值显示◆电阻率显示◆水温显示◆纯水柱更换显示◆“A10”UV灯更换显示◆UV灯更换提示◆UF膜自动清洗◆消毒提醒◆定期循环◆定量取水◆取水纯度设定◆运转状态输出需加装“A10”TOC检测仪技术指标产水量 1.5L/min电阻率18.2MΩ·cm(25℃)总有机碳TOC 〈5ppb热源0.001EU/mL细菌〈1cfu/mL颗粒〉0.22um 〈1P/mLElix产水作为进水，其TOC值低于50ppbMillipore公司是驰名世界的纯水及超纯水设备制造商，根据用户的独特要求设计制造出一系列不同的纯水及超纯水系统。

其中Milli-Q系列更是所有从事化学分析、生化研究及细胞培养所不可缺少的，该系统以反渗透水、蒸馏水、Elix水或去离子水为进水，随时提供符合美国材料试验学会(ASTM)、美国病理学会(CAP)和临床医学会(NCCLS)规定的I级(试剂级)超纯水。

a)纯化系统将自来水作初步处理，一般包括预过滤（深层过滤及膜过滤）和反渗透或蒸馏法，而反渗透因其污染物去除率达到90%-95%以上，回收率达20%-40%以上，效益比传统纯蒸馏法更理想，因此是Milli-Q超纯水系统的理想进水。

另外，Millipore为配合日渐普及的微量分析，研制出Elix连续电流去离子系统，结合反渗透及连续电流去离子技术的优点——经济高效(R〉5MΩ·cm)，可用于一般实验室作分析用水，又因其出水质量高，如作为Milli-Q的进水，更能提高Milli-Q纯化柱的使用寿命及出水水质。

milli-q超纯水仪工作原理

milli-q超纯水仪工作原理一、引言milli-q超纯水仪是一种用于制备高纯度水的设备，广泛应用于实验室、医药、生物技术等领域。

本文将介绍milli-q超纯水仪的工作原理。

二、工作原理milli-q超纯水仪的工作原理主要包括预处理系统、反渗透膜系统、离子交换树脂系统和纯化柱系统。

1. 预处理系统进水经过预处理系统，去除悬浮物、胶体物质、有机物和微生物等杂质。

预处理系统包括粗颗粒过滤器、活性炭过滤器和微孔过滤器。

粗颗粒过滤器能够去除大颗粒的悬浮物，活性炭过滤器则能吸附有机物和余氯，微孔过滤器则能去除微生物和细菌。

2. 反渗透膜系统经过预处理后的水进入反渗透膜系统。

反渗透膜是一种过滤水的膜，具有微孔结构，能够有效去除水中的溶解物质、离子和微生物。

水在反渗透膜上形成一定压力，通过膜的微孔进入膜内，而溶解物质、离子和微生物则被滞留在膜外形成浓缩液。

经过反渗透膜系统的处理，水质得到明显改善。

3. 离子交换树脂系统反渗透膜系统处理后的水进入离子交换树脂系统。

离子交换树脂是一种能够选择性吸附或释放离子的材料。

水中的离子通过树脂床层时，与树脂上的离子发生交换作用，使水中的离子得到进一步去除或净化。

4. 纯化柱系统离子交换树脂系统处理后的水进入纯化柱系统，通过特殊的吸附剂进一步去除残余的有机物和微量离子。

纯化柱系统的吸附剂能够高效地吸附有机物和微量离子，使水质达到超纯水的要求。

三、总结milli-q超纯水仪通过预处理系统去除水中的悬浮物、胶体物质、有机物和微生物，然后通过反渗透膜系统去除溶解物质、离子和微生物，接着经过离子交换树脂系统去除离子，最后通过纯化柱系统去除残余的有机物和微量离子，从而制备出高纯度的水。

这些系统的相互配合使得milli-q超纯水仪能够高效地制备出高质量的水，为实验室和各个行业提供了可靠的实验用水。

MILLIPORE密理博实验室纯水超纯水系统明澈

MILLIPORE密理博实验室纯水超纯水系统明澈-D 24 UVMERCK MILLIPORE 默克密理博实验室纯水超纯水系统明澈-D 24 UV是“基于原密理博成熟技术全新开发的高品质实验室纯水系统”，它以“集成资源，联合开发”的研发模式，建立在原密理博成熟领先的技术，法国优秀的设计，德国严谨的制造基础上，结合中国消费者真实需求全新开发而成。

是直接以自来水为进水生产纯水和超纯水，其中纯水流速为24 升每小时，日产水量在100 升以上；超纯水流速为2 升每分钟。

MERCK MILLIPORE 默克密理博实验室纯水超纯水系统明澈-D 24 UV系统描述：MERCK MILLIPORE 默克密理博实验室纯水超纯水系统明澈-D 24 UV采用原密理博最核心的纯化技术：反渗透、核子级离子交换树脂，185/254 nm 双波长紫外灯，高效率终端除菌过滤器，将自来水处理为满足各类理化、生物等众多实验要求的高品质超纯水。

系统特征CKD-Completely Knock Down-完全进口散件组装明澈-D 24 UV 是以国际先进的CKD 方式生产，及所有散件原装法国生产，国内组装；其次，明澈-D 24 UV 配件均采用国际顶级知名品牌和最好的材质，如Parker、PVDF、PFA 材质软管等。

从而最大限度的保证了设备的耐用性又为客户带来了实惠。

舒适灵活取水明澈-D 24 UV 自带远程取水单元，可实现远程取水，从而节省了实验室大量空间；手臂上可显示产水水质，并给予报警提醒；同时可360 度移动，适合各种容量的玻璃器具250mL 量筒、5 L 长颈瓶、甚至30 L 的大瓶；高精度电导率仪明澈-D 24 UV采用Millipore和德国计量研究员合作开发的高精度电阻率检测器,电导池/电极常数达到0.01 cm-1，温度灵敏度为0.1°C。

该电阻率测量仪能以温度补偿和非温度补偿两种模式显示。

高回收率明澈-D 24 UV 均自带反渗透弃水回收功能，可以将弃水回收，从而提高自来水的利用率，最高回收率可以做到50%。

默克Milli-Q 台式纯水系统

默克M illi-Q®台式纯水系统Milli-Q®实验室用水解决方案的台式水系统系列包括纯水和超纯水两种系统，可满足任何实验室要求。

从灵敏的质控分析到缓冲液制备和玻璃器皿清洗，这一紧凑型系列可解决实验室方方面面的用水需求。

默克的专家可就以下因素，帮助您找到最适合的纯水解决方案：•应用•水质级别•需求容量•实验室配置•预算•根据您的应用选择适合的水质•节省空间且提供从安装到取水的灵活选项•数字化服务简化系统维护根据您的应用选择适合的水质实验室用水级别由ASTM或ISO 3696等质量标准定义，有助于特定应用选择适合的水质。

这些标准也考虑了生产成本，如1级(Type 1)超纯水的生产成本远高于2级(Type 2)或3级(Type 3)纯水。

3级纯水是最低的用水级别，通过反渗透(RO)法生产。

建议在非关键型实验室应用中使用RO水，例如玻璃器皿清洗、加热水浴、高压蒸汽灭菌以及供应1级水系统。

2级纯水建议用于一般实验室应用，例如缓冲液、试剂和培养基的制备以及供应其他设备（如1级系统、临床分析仪、实验室器皿清洗机、稳定性试验箱等）。

默克的2级系统引入绿色的Elix®电去离子(EDI)技术生产质量稳定的纯水，同时无需有害的化学再生步骤、昂贵的树脂、更换去离子滤芯和添加软化剂。

1级超纯水不含离子（电阻率18.2 MOhm·cm）且总有机碳(TOC)含量低。

建议在敏感的实验室应用中采用超纯水，如先进的分析技术（如HPLC、UHPLC、LC-MS、ICP-MS、GF-AAS）、分子生物学应用（如PCR测序）和用于制备哺乳动物细胞培养缓冲液和培养基。

临床实验室试剂级纯水(CLRW)符合美国临床和实验室标准协会(CLSI®)指南制定的质量标准，根据该标准，临床实验室的用水纯度为电阻率>10MΩ·cm；TO <500ppb；细菌<10cfu/mL；颗粒过滤>0.22μm。

Merck Millipore Direct-Q 水纯化系统用户指南说明书

Tap to pure and ultrapure water ― with easy and convenient dispense!Your water purification needs Our solution: the Direct-Q® range of water purification systemsHigh quality water produced directly from tap water Direct-Q® systems deliver both pure and ultra-pure water directly from tap for use with a wide variety of applications in your lab.Ultrapure water easily accessible wherever you need it in your lab With the Direct-Q® range of water purification systems, you benefit from a choice of ultrapure water dispensing possibilities. The innovative, space-saving Remote dispenser offers you water delivery solutions to best fit the way you work, with easy and convenient remote delivery up to two meters away from your water production unit.Compact all-in-one system for the most efficient use of your lab space The Direct-Q® range includes versatile solutions that can be bench-integrated or bench- / wall-installed.A choice of adequate storage volumes Direct-Q® systems come either with an integra-ted 6-liter reservoir or an external reservoir (30 l or 60 l).Flow rates adapted to your daily usage Systems in the Direct-Q® range provide 3, 5 or 8 liters of pure water per hour, covering lab needs of 50,100 and 150 l of pure water per day.Instant flow rates to match your needs Direct-Q® systems dispense up to 30 l ofultrapure water per hour.High quality water to meet the requirements of your most critical applications Options such as a UV lamp and a range of Application Pak point-of-use polishers are available to fine-tune your ultrapure water.Easily accessible information on system operation The user-friendly display provides system status at a glance; the concise Quick Reference Guide is a handy guide for daily operation.Simple, low-level self-maintenance All-in-one SmartPak®cartridges enable easy and rapid replacement.Direct-Q® Systems Water Purification Pathway Choose the solution that’s right for youEasy installationThe Direct-Q® range of systems requires no special installation. You can easily set the system up yourself: just connect the system to your tap water supply, plug it in, and insert the SmartPak® purification cartridges. Then, if your configuration includes the Remote dispenser or a 30- or 60-liter reservoir, follow the simple setup procedures ― and your system is ready to use!Optimized lab spaceThe compact, all-in-one Direct-Q® water purification unit lets you locate it nearly anywhere in your laboratory, either on or under the benchtop, or wall-installed.**Direct-Q® 5 and Direct-Q® 8 systems are designed for use with a 30 l or 60 l external reservoir.Organic-sensitive applicationsDirect-Q® systems are also available with a built-in 185/254 nm UV lamp to reduce the level of organics for critical applications. Water with low TOC provides important benefits to HPLC users such as higher sensiti-vity and longer column lifetime. The same UV lamp also destroys bacteria.Application Pak point-of-use polishersMerck Millipore’s range of Application Pak polishers makes it possible to fine-tune your ultrapure water quality to match your research needs. Are your applications sensitive to bacteria, particulates, pyrogens, nucleases, endocrine disruptors or Volatile Organic Compounds? If so, just choose the appropriate final polisher from our range of Application Paks to provide optimal water quality for your requirements.Please see /labwater for more information.Both pure and ultrapure waterThe Direct-Q® range of systems provides you with a convenient and flexible solution for your pure and ultrapure water needs, directly from potable tap water. You’ll have access to ultrapure water for your critical applications, and pure water for less critical applications such as general glassware washing or final rinsing ― from the same system!The high quality ultrapure water produced by Direct-Q® systems is suitable for applications such as production of mobile phase for chromatographic separations; preparation of blanks and standard solutions for spectrophotometry, spectroscopy or other analytical techniques; and preparation of buffers for biochemical experiments.Flow rates to match your requirementsChoose the solution that best meets your lab’s requirements with a Direct-Q®system that provides 3, 5, or 8 liters of pure water per hour, and more than 0.5 l of ultrapure water per minute (> 30 l per hour). When not in use, the Direct-Q® system automatically recirculates water in order to maintain high water quality,so that you do not have to wait when sourcing ultrapure water. For your conve-nience, and to save time, you can also set the system to automatically deliver your selected volume of ultrapure water on demand.Choice of storage volumesWith its built-in reservoir, the Direct-Q® 3 system can store 6 l of reverse osmosis (RO) water, while Direct-Q® 5 and 8 models are designed for use with a 30- or 60-liter reservoir. Just choose the storage volume that best meets yourdaily water volume needs.Fine-tune your water qualityVersatile remote dispenserDesigned to fit perfectly into your lab environment, the versatile Remote dispenser can be placed up to two meters from your Direct-Q® water purification unit. Select the free-standing or wall-installed model according to your needs ― their ergonomy will make either one a welcome addition to your lab,giving you the freedom to focus on your research, while dispensing ultrapure water exactly where you need it. Alternatively, Direct-Q® systems are also available with an integrated dispenser for use on the benchtop.The design of the bench-installed Direct-Q® systems is also adapted to the height and shape of common laboratory glassware.Stay focused on your workMerck Millipore offers more than waterJust the information you needThe intuitive color graphic display shows key system parameters at a glance,enabling easy water quality and maintenance warnings monitoring; the screen rotates for easy viewing wherever thesystem is located. A short Quick Reference Guide is conveniently located in the base of the system for immediate information; the complete User Manual can be stored at the back of the water purification unit.User-friendly maintenanceThe all-in-one SmartPak® purification cartridges are easily replaced in just a few minutes.Watercare Pact Service portfolioTo optimize the performance and lifetime of your water purification system,Merck Millipore offers a complete portfolio of Service plans ranging from a single annual checkup to a full system cover. For more information, please check with your Merck Millipore applications specialist or visit our website:/labwaterSpecificationsAvailable System ConfigurationsWater Purification Systems* 30 l or 60 l depending on daily water usageFor more information, please visit our website:/directq358Millipore, Direct-Q®, SmartPak®, Millipak® and BioPak® are registered trademarks of Millipore Corporation. Merck Millipore and the M mark are trademarks of Merck KGaA.Lit. No. PB2040EN00© 2011 Millipore Corporation, Billerica, MA, U.S.A. All rights reserved.。

Milli-Q Reference 纯水系统说明书

Ultrapure water byMerck MilliporeScientists today face many challenges. As always, they need to deliver high quality technical results. But now, they must do so at a faster pace, while meeting increasing standards and often operating in laboratories with limited space.Merck Millipore designed the Milli-Q® Reference system to address these needs. From pure water, the system produces ultrapure water adapted to your specific applications and exceeding the requirements of the most demanding norms.We’ve achieved all this with a new purification strategy. Water is purified in a first step to reach a resistivity of 18.2 MΩ.cm at 25 °C and a TOC value below 5 ppb. This water is sent through a small recirculation loop to the Application-Pak, where a final purification step, critical for specific experiments, removes contaminants just before water leaves the system.The flow schematic on the next page shows how the water is purified and delivered by the system.Convenience in water deliveryThe Milli-Q® Reference system delivers water the way scientists need it for convenience and time savings, improving laboratory efficiency.Easily prepare solutions with the low flow function to precisely adjust the meniscus in volumetric flasks.The 75 cm long tubing reaches the sink for easy glassware washing.Save time with the volumetric function, automatically deli-vering the water volume that you need, designed to fit the height&shape of all labora-tory glassware.Deliver water hands-free using the footswitch op-tion for more convenience.2Milli-Q® Reference System at a glanceApplication-Pak adapted to specific contaminants removalConsistent delivery of Ultrapure quality water adapted to your needsDispenser on support adapted to glassware height and shape for automatic volume deliveryRange of accessories & optionsQuantum® polishing cartridge adapted to general applicationQ-Gard® pretreatment pack adapted to pure feed water qualityLarge digital & graphic screen with detailed procedures for full on line support34A Quick Reference Guide located in the door of the Milli-Q® Reference water system provides additional support for retrieving information. The system comes with a complete and detailed user manual in 8 languages on CD-ROM. A printedmanual contains essential information (in local language).E asy accEss to informationAccess to water system data is structured simply, so you can save time instead of searching endless numbers for the one you want.The Main Screen on the production unit delivers detailed information in (local language) on system operation and performance. Clear graphics help you perform specific tasks such as maintenance. From the same screen, you can even print reports on the system’s water quality and history.Fields related to critical information such as the definition of water quality set points are accessible only to the designated responsible user and are protected by an identification code and a password.Alerts & alarms are clearly visible on the system’s main screenand can be enhanced by a buzzer.• You can replace the Q-Gard® pretreatment pack or the Quantum® polishing cartridge in less than 5 minutes. These consumables have an RFID tag, automatically registering the catalog and lot number of the new unit in the system’s memory, so that you can quickly and easily maintain traceability.ServiceMerck Millipore provides a comprehensive range of service programs performed by certified Merck Millipore field service support engineers to thoroughly maintain and validate your Milli-Q® system, complying with your industry’s regulatory standards.The service program portfolio covers all maintenance requirements such as installation, customized user training, scientific and technical support, troubleshooting, preventive maintenance visits, and all validation requirements using ad hoc calibrated equipment, procedures,workbooks and suitability tests within a GXPs environment.Q-Gard® Pretreatment PackQuantum®Polishing CartridgeTOTAL WATER SOLUTIONSTo get the best results from your Milli-Q ® Reference system, Merck Millipore recommends feeding it with pure water produced by RiOs™ (Type 3) or Elix® (Type 2) water systems.• The UV lamp built inside the system is designed to last at least 2 years.• The system will alert you to replace consumables or schedule service visits at least 15 days before maintenance is actually required, soyou’ll never be without the water you need.Application-Pak• Replacing the Application-Pak takes less than 2 minutes.Easy and reduced maintenanceMaintaining the Milli-Q® Reference system won’t take time away from your research. Maintenance frequency is minimal, and the procedures are simplified to the utmost.6Feed Water Specifications * For pressure above 0.3 bar, a pressure regulator needs to be installed upstream of the system; for pressures between 0 and -0.2 bar, the system will operate, butproduct flow rate may be lower.Milli-Q® Reference System Dimensions Product Water Quality 1Resistivity can be displayed temperature-compensated at 25 °C or non-temperature-compensated as required by USP 2TOC spec – Test conditions: Milli-Q® Reference system equipped with Q-Gard® T1 pack and Quantum® TEX cartridge, feedwater produced by Elix® system with resistivity > 1 MΩ.cm at 25 °C, TOC < 30 ppb. Product water quality may vary due to local feed water conditions.3Results with Millipak® filter 4Results with Biopak® final polisher in placeThese values (validated with Elix® feed water) are typical and may vary dependingon the nature and concentration of contaminants in the feed water.Q-POD® Accessory Dimensions SafetyThe Milli-Q® Reference system is tested by an independent and accredited company for compliance with the CE directives related to safety and electromagnetic compatibility. The report can be consulted on demand.The Milli-Q® Reference system is built using components and practices recommended by UL and has been cUL marked. The registration can be verified on the UL web site ().CertificationThe Milli-Q® Reference system is delivered with a Certificate of Conformity ensuring that it has been built and tested fully assembled following Merck Millipore Standard Operating Procedures and a Certificate of Calibration for the temperature and resistivity meters built in the system. The Milli-Q® Reference consumables are automatically delivered with a Certificate of Quality.Merck Millipore’s manufacturing site is ISO® 9001 v.2000 and ISO® 140001 certified.A report on conformity of Milli-Q® Reference water quality to Type 1 water quality as described by ASTM®, ISO® 3696 and CLSI® norms and to Purified Water as described in USP and EP is available upon request.Milli-Q® Reference system water specifications7AccessoriesCustomize your Milli-Q® Reference system to meet your specific needs.Space SaversSave your bench space for your crucial experiments by removing the arm and dispenser from the Milli-Q® Reference system and mounting it on the Q-POD® support. Place the water purification cabinet under your bench, or high on a wall, freeing your bench for your research. More space savers include:• Milli-Q® Reference Wall Mounting Bracket • Q-POD® Wall Mounting Bracket• Increase access to water from your bench • Save even more spaceQ-POD® Dispenser: Water delivery at your fingertips The ultrapure water produced in the cabinet is sent in a small recirculation loop to the outlet of the Q-POD® dispenser. Water is delivered from the Q-POD® outletThe Q-POD® dispenser is loaded with convenient features: • Variable water flow (slow flow to 2 L/min) controlled by plunger• H and-held gun dispensing option to facilitate washing applications• Volumetric dispense control with + and – buttons to select dispensed volume• Multicolor graphic display shows at a glance that the water quality is within specification and the system is operating without alarms.• Printer connection to instantly record water quality historySystem ProtectorsSensors can help keep your Milli-Q® Reference system running with minimal vigilance on your part.• Water Sensor – Placed on the floor, this sensor stops water feed to the system if there is water on the floor. No more water spills, even if users forget to stop water delivery while filling containers.• Feed Water Conductivity Meter – If ionic contamination of feed water exceeds specifications, causing high conductivity, an alarm will alert you.• Level Sensor – If your Milli-Q® Reference system is fed from a Merck Millipore tank, this electronic connector transfers tank level information to the Milli-Q® system. The sensor stops water feed from an empty tank and lets you check water levels in the tank before sourcing water, preventing air from entering the system.• Silicone Q-POD® Cover – The Q-POD® dispenser is designed to operate in a wet environment. However, this silicone cover protects your Q-POD® from harsh chemicals, solutions or solvents.FootswitchConnect the footswitch to the base of the Q-POD® dispenser or directly to the Milli-Q® system for hands-free water delivery: pressonce to start and once to stop.Merck Millipore, the M mark, BioPak, Millipak, Milli-Q, Q-POD, Q-Gard, Quantum and Elix are registered trademarks of Merck KGaA, Darmstadt, Germany. RiOs is a trademarks of Merck KGaA.ASTM, ISO, and CLSI are registered trademark of their respective owners.PB0015EN00© 2013 EMD Millipore Corporation, Billerica, MA, U.S.A. All rights reserved.。

MilliporeSigma Milli-Q EQ 7000 超纯水纯化系统说明书

The life science business of Merck operates as MilliporeSigma in the U.S. and Canada.Lab Water SolutionsMilli-Q ® EQ 7000Ultrapure water purification systemThe AuthenticMilli-Q ® Ultrapure ExperienceDesigned for Modern-Day ScientistsScientists Face Many Challenges. Water Should Not Be One of Them.To deliver reliable, high-quality scientific results, you require consistently high-quality ultrapure water.The Milli-Q ® EQ 7000 ultrapure water system is designed to produce consistent ultrapure water quality[resistivity 18.2 MΩ·cm @ 25 °C; total organic carbon (TOC) ≤ 5 ppb] that can be adapted to each user’s specific application requirements. Plus, a range of intelligent design features make it effortless to dispense water as needed and where needed in the lab.An ultrapure water system designed by scientists, for scientists.2* Vs. our previous generation Milli-Q ® Reference system.Convenient Q-POD ® dispensing• 3 flow rates or one-touch volumetric dispensing • Dispenser mounts where you want, up to 3 m from the system • Confidence as you work with ‘Check & Dispense’ lightsFlexibility that adapts to your needs• Multiple space-saving setups: on or under the bench, or on the wall • Customize water quality with application-specific final filters • Hands-free dispensing foot pedal optionControl at your fingertips• Large, intuitive touchscreen simplifies system use and data access • Place the screen where you want, up to 3 m from the systemAt-a-glance quality monitoring• Rapid quality monitoring assures your every dispense • Inline proprietary TOC indicator measures at the point of useCreate a compact & flexible benchtopsetup by systemmounting the Q-POD ® dispenserand placing the screen anywhere on the bench, up to 3m.Save space by placing the system (A) on the wall, or (B) under the bench.Feed pure water from a pressurized loop or storage tank.Flexibility that Fits Your Space & NeedsChoose an installation option that works for you3* Feed water must be pretreated with one of the following purification technologies: Elix ® electrodeionization (EDI), deionization (DI), reverse osmosis (RO), or distillation.Production unit installation options• Benchtop • Under bench • Wall mountedPure water* feed options from a• Distribution loop • Milli-Q ® pure water storage solutionQ-POD ® dispenser options• System mount with choice of positions: on the left or right side, and at the top or bottom of the system or• Wall mount, up to 3 m from the systemHMI touchscreen options• Maintain movement flexibility with a 3 m cable that connects the screen to the main unit; Hold, move and use the touchscreen as is most comfortable for you or• Wall mount, up to 3 m from the systemultrapure water• Wall- or system-mounted setup options (see page 3)• Q-POD ® dispenser rotates on a fixed arm for convenient filling • Unhook the Q-POD ® dispenser from its magnetic hold for agile manipulationConfidenceCheck & Dispense lights on the Q-POD ® arm rapidly confirm that your every dispense is a high-quality dispense.System power Water quality 4…With All Information at Your FingertipsUser-friendlytouchscreen interfaceNavigate and control yourMilli-Q ® EQ 7000 system efficiently and effortlessly with its 7” (~18 cm) colored, touchscreen.Intuitively organized menus help you quickly find what you’re looking for, including:• System information and controls • Water quality monitoring • Dispense options• Purification cartridge status • Data access and reportsAt-a-glancequality monitoringEssential water quality information is conveniently in view on the touchscreen interface:• Resistivity and temperature • TOC indication (see page 7 for more information)• Application POD-Pak installed • Water recirculation statusAfter each dispense, updated resistivity and temperature measurements and the TOC indication are displayed on the screen.Connect to simplified system monitoring & data managementConnect your Milli-Q ® EQ 7000system to an authorized network or device:• Local network (DHCP protocol/fixed IP address) via an Ethernet port• Laptop with a fixed IP addressConnectivity facilitates:• Remote system monitoring and control • Rapid data access• Paperless data managementAlternatively, data can be transferred to a USB key from the port on the touchscreen.Just tap or swipe to control and monitor your system and its data.Intuitively organized system menus support ease of use and greaterlab efficiency.Colored icons display the status of installed purification cartridges.Essential water quality information is in view.A USB port supports easydata export.5Support for Your Sustainability GoalsAt Lab Water Solutions, we are proactively engaged in reducing the environmental impact of our products and supporting your efforts to identify more sustainable solutions. All our products are produced at our ISO 14001 and ISO 50001 certified manufacturing site and all our systems comply with critical environmental regulations and directives, such as RoHS, REACH and WEEE.We are proud of the innovation and design features that give the Milli-Q ® EQ 7000 system a reduced environmental footprint vs. our previous generation Milli-Q ® Reference system:Reduced plastic and size• 20% reduced plastic weight • Up to 25% smaller footprint• 33% smaller and lighter purification cartridges. Smallerbeads of IQnano ® ion-exchange media reduce the bedvolume and improve kinetics within the IPAK Quanta ®and IPAK Meta ® polishing cartridges.• >50% plastic by weight from suppliers following the Together for Sustainability approach, audited by EcoVadis.Reduced electricity consumption• >10% overall energy savings• Lab Close mode saves energy and reduces wear of system components as recirculation is reduced to once a day during long periods of inactivity. The system automatically resumes hourly recirculation 24 hours prior to resuming lab activity, ensuring the system is ready for use.Easy Upkeep & Carefree MaintenanceWe’ve made the Milli-Q ® EQ 7000 system easy to use and carefree to maintain so that your valuable resources can focus on what truly matters – accurate scientific results.• Automated quality upkeep , including a recirculation loop and Lab Close mode, ensure that water quality is preserved when the system is not in use • Automatic alerts notify youwhen purification cartridges need replacing to avoid risk of impacting major components• Coordinated, once-a-yearpurification cartridge replacements minimize hassle • Onscreen wizards guide you to perform simple maintenance and troubleshooting procedures in-house • Twist & Lock cartridgereplacements can be confidently performed by anyone in the lab in a few minutes • Predictableoperating costsTo replace purification cartridges, scan the QR code to be automatically connected to:/mymilliqconsumablesTwist & Lock cartridgedesign makes consumable changes easy and fast.In 2020 and 2021, Merck KGaA, Darmstadt, Germany was awarded Platinumstatus from EcoVadis, placing us in the top 1% of all companies assessed.6Work Confidently with Authentic Milli-Q ® Ultrapure WaterThe Milli-Q ® EQ 7000 system produces ultrapure water that exceeds the requirements of the mostdemanding norms and can be adapted to your specific applications. (See page 10 for details on how water is purified and delivered by the system.)Water quality gradeWith respect to daily, freshly produced water, the Milli-Q ® EQ 7000 system is intended to dispense ultrapure water that meets or exceeds water quality specifications described by the organizations below:OrganizationWater quality/gradeEuropean Pharmacopoeia Purified water in bulk U.S. Pharmacopeia Purified water in bulk Japanese Pharmacopoeia Purified water Chinese Pharmacopoeia Purified water ASTM ® D1193 Type I water ISO 3696Grade 1 water Chinese National Standard GB/T 6682Grade 1 water Chinese National Standard GB/T 33087Ultrapure water JIS K 0557A4 waterClinical and Laboratory Standards Institute (CLSI ®)Clinical Laboratory Reagent Water (CLRW)Rapid, inline Milli-Q ® TOC indicatorTo ensure the reliability of your organic-sensitive applications, such as HPLC, the Milli-Q ® EQ 7000 system integrates a new, proprietary TOC indicator that assures organic contamination is ≤ 5 ppb. This inline indicator provides TOC at the point of use, so you’re certain every dispense is an optimal dispense.ParameterMilli-Q ® TOC IndicatorMonitoring frequency At dispenseAccuracyAccurate indication within the range TOC values display ≤ 5 ppb, if 0–5 ppb ≤ 10 ppb, if 6–10 ppb>10–999 ppb, a whole number is displayed TOC measuring process Inline, post-dispensePhotooxidation UV lampLow pressure mercury lamp, 185 nm UV lamp replacement frequencyOnce every 2 yearsMilli-Q ® TOC IndicatorOnce a dispense is complete, product water flows through the recirculation loop inside the system to the UV oxidation lamp, bypassing theIPAK Meta ® polishing cartridge. UV radiation oxidizes neutral organics into charged molecules, increasing water conductivity. This change is detected by an intermediate resistivity sensor and is converted by an algorithm to a TOC value. The TOC indication appears on the touchscreen monitor after eachdispense.7A Powerful Combination of Purification MediaSlim IPAK Meta ® and IPAK Quanta ® cartridges are designed to function as a pair. The cartridges use acombination of Jetpore ® mixed-bed ion-exchange resin and innovative IQnano ® ion-exchange media to provide exceptional performance. The IQnano ® media’s smaller bead size significantly improves the resin’s kinetic properties. This reduces media needs dramatically: 33% less than former Milli-Q ® cartridges — while still achieving ion removal down to trace level.Other available POD-Paks include: • EDS-Pak ® polisher for endocrine disruptor experiments • LC-Pak ® polisher for trace and ultra-trace organic analyses • VOC-Pak ®polisher for analysis of volatile organic compoundsAll Application POD-Paks feature:• e-Sure tags for full data traceability and consumable status monitoring • Easy snap-into-place installation •Dispensing protective bell8Match Water Quality to Your NeedsApplication POD-Paks are final filters that adapt water quality to specific application needs. Each targets specific contaminants and removes them right at the Q-POD ® dispenser.Millipak ® & sterile Millipak ® Gold 0.22 μm filters to remove bacteria and particulates from water.Biopak ® ultrafiltration polisherfor critical applications requiring pyrogen-, nuclease-, protease- and bacteria-free water.Jetpore IQnanoIPAK MetaIPAK QuantaActivated carbonIQnanoTrust Best-in-Class Milli-Q ® ServicesAnd save time with MyMilli-Q™ digital servicesFrom installation and training to yearly check-ups and our timesaving digital solutions, with Milli-Q ® Services you receive best-in-class service and support from the people who designed and built your system.Quality certified & globally harmonized expertise• Only Milli-Q ®-certified field service engineers install, maintain and repair our systems • Genuine parts from our ISO 9001-certified manufacturing site• In compliance with our worldwide, auditable Standard Operating Procedures • Standardized visit reports and traceable records of careInstallation & user training• Highly trained engineers efficiently install your system, supplying all components required • Receive user training and advice on how to use your systemMilli-Q ® Service Plans & support options to meet any lab’s needsTo ensure your Milli-Q ® system continuously operates at optimum efficiency, we provide a range of service plans and options that can be tailored to suit your application, compliance and budgetary requirements. All Milli-Q ® Service Plans include an annual preventive maintenance visit from one of our engineers and access to our cloud-based digital service portal, MyMilli-Q™ online solution.Milli-Q ® digital servicesLog into MyMilli-Q™ online solution to streamline the care of your Milli-Q ® systems:• Track service history and reports • Manage purification cartridge deliveries • Plan maintenance visits• Renew service contracts and Consumable Supply Agreements ® Services hotline* For the Milli-Q ® EQ 7000 system, applies to temperature and conductivity cells.:/milli-qservices9Customized installationUser trainingVerificationand calibration*Technical AppendixMilli-Q® EQ 7000 ultrapure water systemThe Milli-Q® EQ 7000 system manages the production and the distribution of ultrapure (Type 1) water from a purified water source, such as a PE tank, the Milli-Q® IX/IQ tank, or a pressurized loop.Water is purified to a resistivity of 18.2 MΩ.cm at 25°C and TOC ≤ 5 ppb. During dispense, water is sent through a small recirculation loop to the Q-POD® dispenser where a final purification step—the Application POD-Pak—removes specific contaminants just before water leaves the system.Flow schematic1011Purification unit specificationsCompact benchtop solutionBenchtop HMI touchscreenRemote wall-mounted solutionFront viewTop viewFront viewTop view34.2 cm [13.4 in]19 cm [7.4 in]19 cm [7.4 in]49.8 c m [19.6 i n ]18.6 c m [7.3 i n ]54.2 c m [21.3 i n ]35 c m [13.8 i n ]9.4 c m [3.7 i n ]43.7 c m [17.2 i n ]11.3 cm [4.4 in]26.5 cm [10.4 in]26.5 cm [10.4 in]35 c m [13.8 i n ]52 c m [20.5 i n ]77 c m [30.3 i n ]49.8 c m [19.6 i n ]Tubing and port requirementsParameter DescriptionFeed water connection½” GAZDistance from feed water port Maximum 5 m (16.4 ft)Distance from purification unit to wall-mountedQ-POD® dispenser Maximum 3 m (9.8 ft)Power entry Connection IEC13ON/OFF switch Avaliable on the unitWater sensor port Fits with standard leak detector (Cat. No. ZWATSENA1) Ethernet port IEEE P802.3Electrical connections and specificationsParameter DescriptionPower source voltage100–240 VAC ± 10%Power frequency50/60 Hz ± 2 HzPower used Maximum 115 VAPower cord length 2.5 m (8.2 ft) plug: IEC13 femaleOperational temperature4–40 °C (39–104 °F)Altitude Up to 3000 m (9842 ft)WeightsSystem type Dry weight Shipping weight Operating weight Purification unit + HMI touchscreen12.2 kg (26.9 lb)*14.6 kg (32.2 lb)16.7 kg (36.8 lb)* HMI touchscreen 0.58 kg (1.3 lb) **0.58 kg (1.3 lb)HMI touchscreen mounting kits • Benchtop• Wall 0.42 kg (0.9 lb)0.49 kg (1.1 lb)0.56 kg (1.2 lb)1.4 kg (3.0 lb)0.42 kg (0.9 lb)0.49 kg (1.1 lb)Q-POD® dispenser • System• Wall 1.2 kg (2.7 lb)2.2 kg (4.9 lb)1.5 kg (3.3 lb)2.8 kg (6.1 lb)1.2 kg (2.7 lb)2.2 kg (4.9 lb)*HMI touchscreen not included.**Included in shipping box with purification unit.HMI touchscreen specificationsScreen descriptions and functionalitiesParameter DescriptionCapacitive touchscreen Size: 7” (18 cm); Resolution: 800 x 480USB port USB 2.0 Highspeed standardDisplay in 9 languages Chinese / English / French / German / Italian /Japanese / Portuguese / Russian / Spanish12Water specifications international conformityFeed water requirementsFeed water quality Pretreated water using electrodeionization (EDI), deionization(DI), reverse osmosis (RO), or distillation technologies Pressure* < 6 barTemperature5–35 °C (41–95 °F)Conductivity ≤ 100 µS/cm at 25 °C (as NaCl)Total Organic Carbon (TOC)< 50 ppb* For pressures below 0 bar, the system will operate, but product flow rate may be lower.Ultrapure, Type 1 water specifications1 (from Q-POD® dispenser)Resistivity218.2 MΩ·cm at 25 °CConductivity 0.055 μS/cm at 25 °CTOC≤ 5 ppbParticles3No particles with size > 0.22 µmBacteria< 0.01 cfu/mL (< 10 cfu/L)(4)< 0.005 cfu/mL (< 5 cfu/L)(5)Pyrogens (endotoxins)6< 0.001 EU/mLRNases6< 1 pg/mLDNases6< 5 pg/mLProteases6< 0.15 µg/mLFlow rate Up to 2 L/min1 These values are typical and may vary depending on the nature and concentration of contaminants in the feed water.2 Resistivity can also be displayed non-temperature-compensated as required by USP.3 With Millipak® or Millipak® Gold filter.4 With Millipak® or Biopak® filter.5 With Millipak® Gold filter when installed and used in a laminar flow hood.6 With Biopak® polisher.13International regulatory requirements EU declaration of conformity – UL safety markingThe Milli-Q® EQ 7000 system has been designed and manufactured in accordance to the international standard and test method defined by the IECEE organization according CB Scheme process. CB Scheme process was applied for electromagnetic compatibility and safety compliance.The Milli-Q® EQ 7000 system is also subject of the UL listing Marking Program and meets the following marking and registration requirements listed below:• UL registration can be verified on the UL website: • Access to CB certificate: /We also meet the regulatory requirements of the following organizations:14Ordering informationSystem Catalog numberMilli-Q® EQ 7000 water purification system & HMI touchscreen ZEQ7000T0CBenchtop kit for HMI touchscreen BTEQ0DKTWall mounting kit for HMI touchscreen WMEQ0DKTSystem mounting kit for Q-POD® dispenser (includes Q-POD® unit)SMEQ00KTWall mounting Kit for Q-POD® dispenser (includes Q-POD® unit)WMEQ0RKTPure water storage tanks*Catalog numberMilli-Q® storage tank top assembly TANKT0PA1Milli-Q® storage tank, 25 L TANKA025Milli-Q® storage tank, 50 L TANKA050Milli-Q® storage tank, 100 L TANKA100* Also compatible with polyethylene (PE) storage tanks or distribution loop.Purification consumables & Application POD-Paks Catalog numberIPAK Meta®/IPAK Quanta® consumable kit IPAKKITA1Millipak® 0.22 μm filter MPGP002A1Millipak® Gold 0.22 μm sterile filter MPGPG02A1Biopak® polisher CDUFBI0A1LC-Pak® polisher LCPAK00A1EDS-Pak® polisher EDSPAK0A1VOC-Pak® polisher V0CPAK0A1UV lamp ZEQ7UVLP0For easy consumable ordering, visit/mymilliqconsumablesAccessories Catalog numberSystem wall mounting bracket SYSTFIXA1Water sensor ZWATSENA1Foot pedal ZEQ7FTPDLInternal pressure regulator + Feed conductivity cell ZEQ7C0NDCInternal pressure regulator ZF3000810Alarm relay cable ZMQ0ALCA115Lab Water Solutions© 2022 Merck KGaA, Darmstadt, Germany and/or its affiliates. All Rights Reserved. Merck, the vibrant M, Milli-Q, MyMilli-Q, Q-POD, Elix, IPAK Meta, IPAK Quanta, IQnano, Jetpore, Millipak,BioPak, VOC-Pak, EDS-Pak and LC-Pak are trademarks of Merck KGaA, Darmstadt, Germany or its affiliates. All other trademarks are the property of their respective owners. Detailed information on trademarks is available via publicly accessible resources.Lit. No. MK_BR7180ENFor more information, please visit our website:/ultrapureWe have built a unique collection of life science brands withunrivalled experience in supporting your scientific advancements.。

L129 默克密理博超纯水机操作规程-20150519

1 目的规范本检测中心默克密理博Elix Essential Milli-Q超纯水机操作程序。

2 适用范围本规程适用于默克密理博Elix Essential Milli-Q超纯水机。

主要用于检测中心用普通实验用水超纯水和高精仪器超纯水的制备。

3 职责检测中心使用人员应严格按照本使用规程进行操作、维护。

4 定义（无）5 操作方法5.1 接通水源后，接通电源打开机箱后部电源开关，当有原水时，屏幕会显示电导率、剩余水量等。

本机系统即启动运行。

5.2运行一段时间后，水箱达到高水位，增压泵自动停机，屏幕左侧余水显示区满格显示。

水箱水位下降至设定值（默认95%）时，增加泵自动启动主机开始工作，屏幕左侧余水显示区闪动，直到高水位时再自动停机。

5.3纯水取水：打开蓄水水箱正中间的阀门，水箱出水。

再关闭阀门即可停止取用纯水。

5.4超纯水取水5.4.1 不定量取水：当按下取水器Q-POD时，与之连接的底座显示当前水质的电阻值、温度、TOC 值并出水。

再按下即可停止取用超纯水。

根据按压取水器Q-POD的5.4.2 Q-POD底座屏幕，通过“”“”设定需要取水的量后，按最中间的量筒形状的按钮，即可定量取水，待取水量达到所设定的量，超纯水机自动停止出水。

6 注意事项6.1 在按最上方菜单键后出现“沙漏”图标和虚线，制水功能将停止。

超纯水机进入待机模式，等待“沙漏”图标消失，可对仪器进行参数设置。

按向左键“”和菜单键可退出，恢复正常工作。

6.2 不要在水箱没水时取水。

6.3 定期检查预处理器所用耗材更换的时间。

6.4 当仪器出现红色报警信息时或发出蜂鸣报警声时，请及时通知仪器负责人。

7 本文解释权归无穷食品有限公司检测中心。

8 相关文件/资料名称文件编号8.1《水净化系统的性能的检查记录》 WQL-ZJ-839 相关记录（无）10 附录（无）。

纯水超纯一体化智能系统1台

1、纯水超纯一体化智能系统1台厂家：法国密理博型号：Milli-Q Integral 3具体参数：一、主要用途：1.1纯水应用：微生物培养基制备、缓冲液配置、水栽培、实验室前处理设备供水（灭菌锅、自动滴定仪）、CO2培养箱、老化机等;1.2超纯水应用：HPLC/LC-MS/TOF有机物分析仪器及试剂用水、ICP-MS/AAS/ICP/无机分析仪器及试剂用水、IC离子色谱仪器及试剂用水、TOC测量仪器及试剂用水、洁净间仪器及实验用具清洗、凝胶电泳/脉冲场电泳/2D蛋白电泳试剂用水、Ion Torrent等第二代测序仪清洗及试剂用水。

二、工作条件：2.1 环境温度： 5-35℃2.2 相对湿度： 20%-80%2.3 电源：AC220V ± 10%, 50HZ三、技术指标:3.1从自来水直接生产II级纯水和I级超纯水的一体化智能系统，然后由独立的带显示屏的POD 取水器取水3.2 纯水产水：3.2.1电阻率＞ 5 MΩ·cm＠25℃典型值为10-15 MΩ·cm＠25℃3.2.2总有机碳含量(TOC) ＜ 30ppb；3.2.3直径大于0.2μm的颗粒物数量: ＜1/ml3.2.4细菌：＜ 0.1 CFU/ml；3.2.5产水流速：3 L/H3.2.6产水储存于外置同品牌30L非压力水箱，HDPE材质, 圆锥形可完全排空, 配空气过滤器、全量程液位传感器、漏水监测器3.3超纯水产水：3.3.1电阻率：18.2 MΩ.cm@25℃3.3.2 总有机碳TOC≤5ppb3.3.3直径大于0.2μm的颗粒物数量: ＜1/ml3.3.4 * 细菌：＜ 0.01 cfu/ml；3.3.5 * DNases＜5pg/mL；3.3.6 * RNases＜1pg/mL；3.3.7产水流速：0.05 - 2.0 L/min3.4系统监控及主要纯化部件：3.4.1 系统内置高精度电阻率检测仪，电极常数为0.01cm-1，温度灵敏度达到0.1℃, 采用同轴电极专利设计，准确检测和显示温度补偿的电阻率，符合ASTM®D 1125-95(2009)及USP(§645)电阻率系统适应性测试要求，可溯源到NIST，投标文件需附原厂校验证书。

密理博全球发布最新Milli—Q Integral水纯化系统

密理博全球发布最新Milli—Q Integral水纯化系统
佚名
【期刊名称】《现代仪器》
【年(卷),期】2008(14)4
【摘要】2008年4月21日，密理博中国正式对外发布新品-Milli-Q Integral纯水／超纯水一体化系统。

该款纯水系统可以直接以自来水进水，只需经过一台主机，即可得到水质稳定的Ⅱ级纯水和Ⅰ级超纯水。

【总页数】1页(P79-79)
【关键词】超纯水;纯化系统;一体化系统;纯水系统;水质稳定;自来水
【正文语种】中文
【中图分类】TQ085;TQ116.11
【相关文献】
lipore密理博的世纪转型——专访Millipore密理博集团公司主席，全球总裁，首席执行官Martin D.Mudaus博士 [J], 文建平
2.密理博:不断升级食品安全检测配套产品及服务——访密理博中国有限公司总经
理陈亮 [J], 马永娇
lipore新一代Milli-Q Integral实验室水纯化系统 [J],
4.续航变革成长——专访默克密理博过程工艺解决方案全球负责人孟卓理 [J], 曹
竹安
5.悦动指尖·纯水传奇默克全新Milli-Q IQ 7000水纯化系统面世 [J], 杨霞;
因版权原因，仅展示原文概要，查看原文内容请购买。

MERCKMILLIPORE默克密理博Milli-QIntegral实验室纯水超纯水系统

Millipore(密理博)Milli-Q超纯水机维护指导

MERCK MILLIPORE默克密理博Aquelix5实验室纯水机

merck millipore 默克密理博纯水超纯水一体系统明澈D24UV操作手册

默克Milli-Q超纯水解决方案

默克密理博纯水机的优点

MilliporeSigma Milli-Q CLX 7000系列连接水纯化系统用户说明书

默克密理博纯水机的优点

Milli-Q Synthesis 超纯水系统 中文使用说明书

milli-q超纯水仪工作原理

MILLIPORE密理博实验室纯水超纯水系统明澈

默克Milli-Q 台式纯水系统

Merck Millipore Direct-Q 水纯化系统用户指南说明书

Milli-Q Reference 纯水系统说明书

MilliporeSigma Milli-Q EQ 7000 超纯水纯化系统说明书

L129 默克密理博超纯水机操作规程-20150519

纯水超纯一体化智能系统1台

密理博全球发布最新Milli—Q Integral水纯化系统

Milli-Q Synthesis 超纯水系统中文使用说明书