注塑方面英语术语

注塑方面英语术语
压铸die-cast
压炼injection
铸件casting/cast/founding
起泡/气泡bubble/blister/air bubble
缺料shor-shots/undershot
浇不足/*铸under-founding
多料superfluities/superfluous material(alloy) 顶针痕ejector (pins) mark
花纹flow mark/flow line
冷纹cold mark/cold streak
油纹oil streak
走水纹splash mark
银纹silver streaks
霜纹splay mark
夹水纹silver streaks/flow line/weld line 扣模/粘模sprue sticking
砂眼/气眼air hole
（塑胶件）弯曲/变形warping/warpage
变形deformation
扭曲twist
翅曲warp/warped
材料错误using wrong plastic material
凸痕convex mark
凹位/凹陷sink mark/dent mark
披锋flashing
批损pare-mark/cut mark 批凹pare off
锉纹trim-mark/file-mark 锉损excessive trim mark 黑点/黑纹black spots/black streak 发白white mark
烧焦burn marks
刮花/刮痕scratch mark
擦痕/擦伤rub-mark/brush-burn
裂缝cracking
裂纹craking line
碰损stress mark
起皮chip
错位（合模线）part line misaling ment
孔位尺寸改变dimension various
哑色dull color
表面变光滑（喷油面）glossy finishing
表面sruface/outside
镶件insert/insert word
缩水/收缩sink mark/shrinkage/shrink mark 偏差color deviation
色粉colourment
颜色colour/color
零件污糟dirty mark on part
顶白stress mark/ejector mark
屈曲bent
夹模线移位part line misalignment 胶件料厚不均uneven wall thickness 水口料degraded material
凹印sink mark
擦花abrasion mark
混色contamination mark 热点不良poor heat sticking
定位圈locating ring
唧嘴sprue bush (浇口套) A板 A plate (定模板)
B板 B plate（动模板）
方铁spacer block (垫铁)
底板bottom clamp plate(动模底板) 面板top clamp plate(定模底板)
顶针ejector pin（顶杆）
直边钉guide pin (导柱)
托司shoulder guide bush(导套)
直司straight guide bush(导柱)
回针return pin(回程杆)
细水口边钉support pin(副导柱)
蓝弹簧blue spring（回程弹簧）
水口推板runner stripper plate(卸流道板)
中边钉ejector guide pin (顶板导柱)
顶针板ejector retainer plate(顶杆固定板) 顶针底板ejector plate(顶杆垫板)
撑头support pollar（支撑柱）垃圾钉stop pin (限位钉)
呵core (后模肉内镶件)
后模肉back mold body(后模镶件) 前模肉cavity（前模镶件）
扣鸡P-lock
blister 起泡
blooming 起霜
blow hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱check 细裂痕
checking 龟裂
chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷
color mottle 色斑
corrosion 腐蚀
crack 裂痕
crazing 碎裂crazing 龟裂deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑fissure 裂纹
flange wrinkle 凸缘起皱flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕haircrack 发裂
haze 雾度
incrustation 水锈indentation 压痕
internal porosity 内部气孔mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
orange peel 橘皮状表面缺陷overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀plate mark 模板印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹
resin wear 树脂脱落
riding 凹陷
sagging 松垂saponification 皂化
scar 疤痕
scrap 废料
scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕
shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕
skin inclusion 表皮折迭straightening 矫直streak 条状痕
surface check 表面裂痕
surface roughening 橘皮状表皮皱折surging 波动
sweat out 冒汗
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)毛边
flash(塑件)毛边
poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质
painting peel off脏污shrinking/shrinkage缩水mixed color杂色
scratch划伤
(Flow Line)流痕
(Weld Line) 熔接线
Sink Mark凹陷
Streak条纹Warpage翘曲。