产品数据表
DIN439B-DIN936-EN14399 产品尺寸数据表
螺母尺寸图
头标：1为制造商厂标
32.95 35.ห้องสมุดไป่ตู้3 39.55
六角薄螺母Hexagon Lock Nuts DIN936
Size规格 P螺距 m max. 厚度 min. s max. 对边 min. e min. 对角 Size规格 P螺距 m max. 厚度 min. s max. 对边 min. e min. 对角 M8 M10 1 25 1.25 1.5 15 5 6 4.7 5.7 17 13 16.73 12.73 14.38 M27 3 12 10.9 41 40 45.2 18.9 M30 3.5 12 10.9 46 45 M12 1 75 1.75 7 6.64 19 18.67 21.1 M33 3.5 14 12.9 50 49 M14 2 8 7.42 22 21.67 24.49 M36 4 14 12.9 55 53.8 60.79 M16 2 8 7.42 24 23.67 26.75 M39 4 16 14.9 60 58.8 66.44 M18 2.5 25 9 8.42 27 26.16 29.56 M42 4.5 16 14.9 65 63.1 71.3 M20 2.5 25 9 8.1 30 29.16 32.95 M45 4.5 18 16.9 70 68.1 76.95 M22 2.5 25 10 9.1 32 31 35.03 M48 5 18 16.9 75 73.1 82.6 M24 3 10 9.1 36 35 39.55 M52 4.5 20 18.7 80 78.1 88.25
六角薄螺母Hexagon Lock Nuts DIN439B
Size规格 P螺距 m max. 厚度 min. s max. 对边 min. e min. 对角 Size规格 P螺距 m max. 厚度 min. s max. 对边 min. e min. 对角 M3 0.5 1.8 1.55 5.5 5.32 6.01 M20 2.5 10 9.1 30 29.16 M3.5 0.6 2 1.75 6 5.82 6.58 M22 2.5 11 9.9 32 31 M4 0.7 2.2 1.95 7 6.78 7.66 M24 3 12 10.9 36 35 M5 0.8 2.7 2.45 8 7.78 8.79 M27 3 13.5 12.4 41 40 45.2 M6 1 3.2 2.9 10 9.78 11.05 M30 3.5 15 13.9 46 45 50.85 M8 1.25 4 3.7 13 12.73 14.38 M33 3.5 16.5 15.4 50 49 55.37 M10 1.5 5 4.7 17 16.73 6 3 18.9 M36 4 18 16.9 55 53.8 60.79 M12 1.75 6 5.7 19 18.67 21.1 M39 4 19.5 18.2 60 58.8 66.44 M14 M16 M18 2 2 2.5 7 8 9 6.42 7.42 8.42 22 24 27 21.67 23.67 26.16 24.49 26.75 29.56 M42 4.5 21 19.7 65 63.1 71.3 M45 4.5 22.5 21.2 70 68.1 76.95 M48 5 24 22.7 75 73.1 82.6
产品安全数据表
行避难。后续的灭火活动交给消防人员即可。特别是火势大时则更危险。
泄漏时的措施
尽快清除附近的着火源，已着火时，预备合适的灭火器具。
发生泄漏(喷射时)时，应从上风侧进行处理，将容器的泄漏部位朝上放置，待气体完全喷出后再进行处置。
针对人体的注意事项
穿戴合适的防护用具(橡胶手套、防护眼镜等)，避免产品直接与人体接触。
蒸气压力
喷射剂(LPG) 无色透明液体
无味 -42.1℃ 0.508(15℃) -104.4℃ 460～550℃ 2.2～9.5% 1.275Mpa(40℃)
稳定性及反应性
稳定性
：通常使用条件下稳定
回避状况
：无
混入回避物质
：无
有害分解物质
：无
燃烧临界点(空气中) ：下限＝无 上限＝无
自然点火温度(℃) ：无
(配件和制动器清洗剂 S(中国产)) 2/4
发生火灾时的措施
可使用的灭火剂 ：使用雾状灭火液、泡沫、粉末或二氧化碳灭火剂有效。
灭火方法
：切断火源的燃烧物品。
初期灭火可用粉末、二氧化碳。
大规模的火灾时，使用泡沫灭火பைடு நூலகம்等隔断空气比较有效。避免用水枪灭火，否则
可能会扩大火灾。
用水喷洒周围的设备等物品使其冷却。
(配件和制动器清洗剂 S(中国产)) 1/4
产品安全数据表
制造者资料
整理号
公司名称 地址 负责部门 电话 修订
株式会社 MOKUKEN 大阪府大阪市此花区岛屋 4-3-43 研究部 06-6460-3120 传真 06-6460-0052 2006 年 2 月 3 日 06 版
产品名称(化学名称、商品名称等) 配件和制动器清洗剂 S(中国产：10270、10468) PBCL840
产品安全数据表
产品安全数据表1995年10月3日修订 1. 制造者资料【公司名称】 株式会社 AUDEC【地 址】 东京都大田区东马込2-19-10 第7下川大楼【负责部门】 气雾剂产品部【电 话】 03-3774-5259 【传 真】 03-3776-0881【紧急联系电话】 03-3774-5259/03-3771-68032.产品名称 金属烧结防止剂 SEZCUT4203.产品规格 气雾剂4. 物质特点【单质产品·混合物的区分】 混合物【化学名称】 铝粉末和液化石油气(L.P.G)的混合物【成分、含量及其它信息】化学名称 *1 铝糊剂 二氯甲烷* 液化石油气 其它含量 5% 35% 57% 2%分子式 AL CH2Cl2日本官报公布整理号 不适用 (2)-36 不适用或(9)-1697CAS No. 7429-90-5 75-09-2联合国分类 4.1级 6.1级 等级Ⅲ2级 副次危险3级联合国编号 1309 1593 1075*1记载了占铝糊剂85％的有关铝的资料。
5. 危险·有害性分类【分类名称】 易燃性固体、急性毒性物质以及高压气体【危险性】 火灾、易爆性 【有害性】 有毒性【环境影响】 *以下都为二氯甲烷资料◇分解性◇浓缩性(倍率)◇鱼毒性 原料中所用的铝糊剂中铝的特性，加热后会产生在空气中易爆的混合气体。
遇高温表面、火星或明火则会着火。
与水、酸或碱接触，会产生热量和氢气，因此在密闭的空间有引发爆炸的危险。
用于喷雾剂的液化石油气易爆炸。
另外，液化石油气比空气重，易积聚在低处。
挥发蒸气刺激人的眼、鼻、咽喉，具有麻醉的作用。
如短时间内吸入大量的高浓度蒸气，则会引起急性中毒。
如长时间或反复接触皮肤，则会引起皮炎。
另外，铝粉尘也具有毒性。
5～26% (by BOD)浓 2.0～5.4倍 (250μg/R) 浓 ＜0.4～40倍 (25μg/R) 绯鲣鱼 LC50/48H 331.0mg/R6. 应急处理【接触皮肤时】 【误入眼内时】 【吸入体内时】 【误饮入时】 脱下污染的衣服，用大量清水冲洗受到接触过的皮肤。
各区域各产品销售数据统计表excel模板
￥12,965.00
产品2
126.00
￥1,800.00
291.00
￥1,900.00
291.00
￥1,900.00
276.00
￥1,600.00
291.00
￥1,900.00
1275.00
￥9,100.00
产品3
510.00
￥3,890.00
292.00
￥2,010.00
492.00
￥5,010.00
销售区域4
销售区域5
合计
产品名称
销售数量 销售额 销售数量 销售额 销售数量 销售额 销售数量 销售额 销售数量 销售额
销售数量
销售额
产品1
289.00
￥1,565.00
290.00
￥2,600.00
380.00
￥3,600.00
290.00
￥2,600.00
290.00
￥2,600.00
1539.00
未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮
未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮
未名潮
未名潮
未名潮
未名潮
未名潮
未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮
未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮 未名潮
产品出入库数据记录表
60 126
0
0
30 63
15 103.5
10 65
10 69
20 130
0
0
40 140
0
0
5 62.5
15 135
10 115
出库数据
数量 金额
0
0
23 248.4
19 171
4 43.2
65 104
45 72
0
0
16 336
2
42
20 276
9 124.2
5
80
8 110.4
50 105
0
0
20 42
袋
D-001 单果粒 草莓125克
条
D-002 单果粒 黄桃125克
条
D-003 单果粒 芦荟125克
条
D-004 单果粒 猕猴桃125克 条
E-001 复合果粒 复合草莓＋树莓 杯
E-002 复合果粒 复合黄桃＋芒果 杯
E-003 复合果粒 复合芦荟＋猕猴桃杯
F-001 果粒250克果粒250克草莓 瓶
期初库存
数量 金额
5
24
0
0
10 90
2 21.6
0
0
0
0
0
0
12 252
0000源自2 25.6116
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
入库数据
数量 金额
EFR32BG22无线Gecko SoC产品系列数据表说明书
EFR32BG22 无线 Gecko SoC 产品系列数据表EFR32BG22无线 Gecko SoC 产品系列是无线 Gecko 产品组合的组成部分。
EFR32BG22无线 GeckoSoC 是实现 IoT 设备上节能Bluetooth 5.2 连网的理想之选。
这款单芯片解决方案结合了 76.8 MHz Cortex-M33 和高性能 2.4 GHz 无线电，旨在为 IoT 连接应用提供行业领先的节能无线 SoC 。
无线 Gecko 应用包括：主要特点•32 位 ARM® Cortex®-M33 内核，最高工作频率为 76.8 MHz•最高 512 kB 闪存和 32 kB RAM •低有功电流和睡眠电流的节能型射频内核•Bluetooth 5.2 测向•集成 PA ，TX 功率高达 6 dBm (2.4 GHz)•通过信任根和安全加载程序 (RTSL) 进行的安全启动•资产标签和信标•消费电子遥控器•便携式医疗器械•蓝牙网状网络低功耗节点•体育、健身和健康设备•联网家庭•建筑自动化及安全Lowest power mode with peripheral operational:EM4—ShutoffEM3—StopEM2—Deep SleepEM1—SleepEM0—Active| Building a more connected world.Rev. 1.11.功能列表EFR32BG22 突出功能如下所列。
•低功耗无线片上系统•高性能 32 位 76.8 MHz MHz ARM Cortex®-M33，带有 DSP 指令和浮点单元，可实现高效的信号处理•高达 512 kB 的闪存程序存储器•高达 32 kB 的 RAM 数据存储器•2.4 GHz 无线电操作•射频性能•在 125 kbps GFSK 的条件下，灵敏度为-106.7 dBm•在 1 Mbit/s GFSK 的条件下，灵敏度为-98.9 dBm•在 2 Mbit/s GFSK 的条件下，灵敏度为-96.2 dBm•TX 功率高达 6 dBm•无线电接收电流为2.5 mA•在 0 dBm 输出功率的条件下，无线电传输电流为3.4 mA•在 6 dBm 输出功率的条件下，无线电传输电流为7.5 mA•低系统能耗•RX 电流为3.6 mA (1 Mbps GFSK)•在 0 dBm 输出功率的条件下，TX 电流为4.1 mA•在 6 dBm 输出功率的条件下，TX 电流为8.2 mA•在 76.8 MHz 活动模式 (EM0) 下，运行功耗为27 μA/MHz•1.40 μA EM2 深度睡眠电流（保留 32 kB RAM，RTC 从 LFXO 中运行）•1.75 μA EM2 深度睡眠电流（保留 32 kB RAM，RTC 从 PrecisionLFRCO 中运行）•0.17 μA EM4 电流•支持的调制格式•2 (G)FSK，可配置完整波形•OQPSK DSSS•(G)MSK•协议支持•Bluetooth 低功耗 (Bluetooth 5.2)•采用到达角 (AoA) 和发射角 (AoD) 实现测向•专有•广泛的 MCU 外围设备选择•模拟数字转换器 (ADC)•12 位，1 Msps•16 位，76.9 ksps•高达 26 个带有输出状态保持和异步中断功能的通用 I/O 引脚•8 信道 DMA 控制器•12 信道外围设备反射系统 (PRS)•4 个 16 位定时器/计数器（3 个比较/捕获/PWM 通道）•1 个 32 位定时器/计数器（3 个比较/捕获/PWM 通道）•32 位实时计数器•24 位低能耗定时器，用于波形生成•1 个看门狗定时器•2 个通用同步/异步接收器/传输器 (UART/SPI/SmartCard (ISO 7816)/ IrDA/I2S)•1 个增强型通用异步接收器/传输器 (EUART)•2 个 I2C 接口，带 SMBus 支持•数字麦克风接口 (PDM)•32 KHz 睡眠晶体更换为精密低频 RC 振荡器•可选 OOK 模式的 RFSENSE•单点校准后具有 +/-1.5 摄氏度精度的芯片温度传感器•宽工作范围•单电源1.71 至 3.8 V•-40°C 至 125°C•安全特性•通过信任根和安全加载程序 (RTSL) 进行的安全启动•硬件加密加速，适用于 AES128/256、SHA-1、SHA-2（高达 256位）、ECC（高达 256 位）、ECDSA 和 ECDH•符合 NIST SP800-90 和 AIS-31 标准的真随机数生成器 (TRNG)•ARM® TrustZone®•使用锁定/解锁功能进行安全调试•封装•QFN40 5 毫米 × 5 毫米 × 0.85 毫米•QFN32 4 毫米 × 4 毫米 × 0.85 毫米•TQFN32 4 毫米 × 4 毫米 × 0.30 毫米EFR32BG22 无线 Gecko SoC 产品系列数据表功能列表1EFR32BG22 Wireless Gecko SoC Family Data SheetOrdering Information 2. Ordering InformationTable 2.1. Ordering InformationLE Long Range (125 kbps and 500 kbps) PHYs are only supported on part numbers which include AoA/AoD direction-finding capability. | Building a more connected world.Rev. 1.1 | 3Table of Contents1. Feature List (2)2. Ordering Information (3)3. System Overview (7)3.1 Introduction (7)3.2 Radio (7)3.2.1 Antenna Interface (7)3.2.2 Fractional-N Frequency Synthesizer (8)3.2.3 Receiver Architecture (8)3.2.4 Transmitter Architecture (8)3.2.5 Packet and State Trace (8)3.2.6 Data Buffering (8)3.2.7 Radio Controller (RAC) (8)3.2.8 RFSENSE Interface (9)3.3 General Purpose Input/Output (GPIO) (9)3.4 Clocking (9)3.4.1 Clock Management Unit (CMU) (9)3.4.2 Internal and External Oscillators (9)3.5 Counters/Timers and PWM (9)3.5.1 Timer/Counter (TIMER) (9)3.5.2 Low Energy Timer (LETIMER) (10)3.5.3 Real Time Clock with Capture (RTCC) (10)3.5.4 Back-Up Real Time Counter (BURTC) (10)3.5.5 Watchdog Timer (WDOG) (10)3.6 Communications and Other Digital Peripherals (10)3.6.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) (10)3.6.2 Enhanced Universal Asynchronous Receiver/Transmitter (EUART) (10)3.6.3 Inter-Integrated Circuit Interface (I2C) (10)3.6.4 Peripheral Reflex System (PRS) (11)3.6.5 Pulse Density Modulation (PDM) Interface (11)3.7 Security Features (11)3.7.1 Secure Boot with Root of Trust and Secure Loader (RTSL) (11)3.7.2 Cryptographic Accelerator (11)3.7.3 True Random Number Generator (11)3.7.4 Secure Debug with Lock/Unlock (12)3.8 Analog (12)3.8.1 Analog to Digital Converter (IADC) (12)3.9 Power (13)3.9.1 Energy Management Unit (EMU) (13)3.9.2 Voltage Scaling (13)3.9.3 DC-DC Converter (13)3.9.4 Power Domains (13)3.10 Reset Management Unit (RMU) (14)3.11 Core and Memory (14)3.11.1 Processor Core (14)3.11.2 Memory System Controller (MSC) (14)3.11.3 Linked Direct Memory Access Controller (LDMA) (14)3.12 Memory Map (15)3.13 Configuration Summary (16)4. Electrical Specifications (17)4.1 Electrical Characteristics (17)4.2 Absolute Maximum Ratings (18)4.3 General Operating Conditions (19)4.4 DC-DC Converter (21)4.4.1 DC-DC Operating Limits (23)4.5 Thermal Characteristics (24)4.6 Current Consumption (25)4.6.1 MCU current consumption using DC-DC at 3.0 V input (25)4.6.2 MCU current consumption at 3.0 V (27)4.6.3 MCU current consumption at 1.8 V (29)4.6.4 Radio current consumption at 3.0V using DCDC (31)4.7 Flash Characteristics (33)4.8 Wake Up, Entry, and Exit times (34)4.9 RFSENSE Low-energy Wake-on-RF (35)4.10 2.4 GHz RF Transceiver Characteristics (36)4.10.1 RF Transmitter Characteristics (36)4.10.2 RF Receiver Characteristics (43)4.11 Oscillators (49)4.11.1 High Frequency Crystal Oscillator (49)4.11.2 Low Frequency Crystal Oscillator (50)4.11.3 High Frequency RC Oscillator (HFRCO) (51)4.11.4 Fast Start_Up RC Oscillator (FSRCO) (52)4.11.5 Precision Low Frequency RC Oscillator (LFRCO) (53)4.11.6 Ultra Low Frequency RC Oscillator (53)4.12 GPIO Pins (3V GPIO pins) (54)4.13 Analog to Digital Converter (IADC) (56)4.14 Temperature Sense (58)4.15 Brown Out Detectors (59)4.15.1 DVDD BOD (59)4.15.2 LE DVDD BOD (59)4.15.3 AVDD and IOVDD BODs (60)4.16 PDM Timing Specifications (61)4.16.1 Pulse Density Modulator (PDM), Common DBUS (61)4.17 USART SPI Main Timing (62)4.17.1 SPI Main Timing, Voltage Scaling = VSCALE2 (63)4.17.2 SPI Main Timing, Voltage Scaling = VSCALE1 (63)4.18 USART SPI Secondary Timing (64)4.18.1 SPI Secondary Timing, Voltage Scaling = VSCALE2 (64)4.18.2 SPI Secondary Timing, Voltage Scaling = VSCALE1 (65)4.19 I2C Electrical Specifications (66)4.19.1 I2C Standard-mode (Sm) (66)4.19.2 I2C Fast-mode (Fm) (67)4.19.3 I2C Fast-mode Plus (Fm+) (68)4.20 Typical Performance Curves (68)4.20.1 Supply Current (69)4.20.2 RF Characteristics (71)4.20.3 DC-DC Converter (72)4.20.4 IADC (72)5. Typical Connections (73)5.1 Power (73)5.2 RF Matching Networks (74)5.2.1 2.4 GHz Matching Network (74)5.3 Other Connections (75)6. Pin Definitions (76)6.1 QFN32 Device Pinout (76)6.2 QFN40 Device Pinout (78)6.3 TQFN32 Device Pinout (80)6.4 Alternate Function Table (81)6.5 Analog Peripheral Connectivity (82)6.6 Digital Peripheral Connectivity (83)7. QFN32 Package Specifications (86)7.1 QFN32 Package Dimensions (86)7.2 QFN32 PCB Land Pattern (88)7.3 QFN32 Package Marking (90)8. TQFN32 Package Specifications (91)8.1 TQFN32 Package Dimensions (91)8.2 TQFN32 PCB Land Pattern (93)8.3 TQFN32 Package Marking (95)9. QFN40 Package Specifications (96)9.1 QFN40 Package Dimensions (96)9.2 QFN40 PCB Land Pattern (98)9.3 QFN40 Package Marking (99)10. Revision History (100)3. System Overview3.1 IntroductionThe EFR32 product family combines an energy-friendly MCU with a high performance radio transceiver. The devices are well suited for secure connected IoT multi-protocol devices requiring high performance and low energy consumption. This section gives a short intro-duction to the full radio and MCU system. The detailed functional description can be found in the EFR32xG22 Reference Manual.A block diagram of the EFR32BG22 family is shown in Figure 3.1 Detailed EFR32BG22 Block Diagram on page 7. The diagram shows a superset of features available on the family, which vary by OPN. For more information about specific device features, consult Ordering Information .RESETnPDnPCnPBnPAnRF2G4_IODVDDVREGVDD VREGSW AVDD PAVDD RFVDD DECOUPLEIOVDD Figure 3.1. Detailed EFR32BG22 Block Diagram3.2 RadioThe EFR32BG22 Wireless Gecko features a highly configurable radio transceiver supporting the Bluetooth Low Energy wireless proto-col.3.2.1 Antenna InterfaceThe 2.4 GHz antenna interface consists of a single-ended pin (RF2G4_IO). The external components for the antenna interface in typi-cal applications are shown in the RF Matching Networks section.Rev. 1.1 | 73.2.2 Fractional-N Frequency SynthesizerThe EFR32BG22 contains a high performance, low phase noise, fully integrated fractional-N frequency synthesizer. The synthesizer is used in receive mode to generate the LO frequency for the down-conversion mixer. It is also used in transmit mode to directly generate the modulated RF carrier.The fractional-N architecture provides excellent phase noise performance, frequency resolution better than 100 Hz, and low energy consumption. The synthesizer’s fast frequency settling allows for very short receiver and transmitter wake up times to reduce system energy consumption.3.2.3 Receiver ArchitectureThe EFR32BG22 uses a low-IF receiver architecture, consisting of a Low-Noise Amplifier (LNA) followed by an I/Q down-conversion mixer. The I/Q signals are further filtered and amplified before being sampled by the IF analog-to-digital converter (IFADC).The IF frequency is configurable from 150 kHz to 1371 kHz. The IF can further be configured for high-side or low-side injection, provid-ing flexibility with respect to known interferers at the image frequency.The Automatic Gain Control (AGC) module adjusts the receiver gain to optimize performance and avoid saturation for excellent selec-tivity and blocking performance. The 2.4 GHz radio is calibrated at production to improve image rejection performance.Demodulation is performed in the digital domain. The demodulator performs configurable decimation and channel filtering to allow re-ceive bandwidths ranging from 0.1 to 2530 kHz. High carrier frequency and baud rate offsets are tolerated by active estimation and compensation. Advanced features supporting high quality communication under adverse conditions include forward error correction by block and convolutional coding as well as Direct Sequence Spread Spectrum (DSSS).A Received Signal Strength Indicator (RSSI) is available for signal quality metrics, for level-based proximity detection, and for RF chan-nel access by Collision Avoidance (CA) or Listen Before Talk (LBT) algorithms. An RSSI capture value is associated with each received frame and the dynamic RSSI measurement can be monitored throughout reception.3.2.4 Transmitter ArchitectureThe EFR32BG22 uses a direct-conversion transmitter architecture. For constant envelope modulation formats, the modulator controls phase and frequency modulation in the frequency synthesizer. Transmit symbols or chips are optionally shaped by a digital shaping filter. The shaping filter is fully configurable, including the BT product, and can be used to implement Gaussian or Raised Cosine shap-ing.Carrier Sense Multiple Access - Collision Avoidance (CSMA-CA) or Listen Before Talk (LBT) algorithms can be automatically timed by the EFR32BG22. These algorithms are typically defined by regulatory standards to improve inter-operability in a given bandwidth be-tween devices that otherwise lack synchronized RF channel access.3.2.5 Packet and State TraceThe EFR32BG22 Frame Controller has a packet and state trace unit that provides valuable information during the development phase. It features:•Non-intrusive trace of transmit data, receive data and state information•Data observability on a single-pin UART data output, or on a two-pin SPI data output•Configurable data output bitrate / baudrate•Multiplexed transmitted data, received data and state / meta information in a single serial data stream3.2.6 Data BufferingThe EFR32BG22 features an advanced Radio Buffer Controller (BUFC) capable of handling up to 4 buffers of adjustable size from 64 bytes to 4096 bytes. Each buffer can be used for RX, TX or both. The buffer data is located in RAM, enabling zero-copy operations.3.2.7 Radio Controller (RAC)The Radio Controller controls the top level state of the radio subsystem in the EFR32BG22. It performs the following tasks:•Precisely-timed control of enabling and disabling of the receiver and transmitter circuitry•Run-time calibration of receiver, transmitter and frequency synthesizer•Detailed frame transmission timing, including optional LBT or CSMA-CA3.2.8 RFSENSE InterfaceThe RFSENSE block allows the device to remain in EM2, EM3 or EM4 and wake when RF energy above a specified threshold is detec-ted. When operated in selective mode, the RFSENSE block performs OOK preamble and sync word detection, preventing false wake-up events.3.3 General Purpose Input/Output (GPIO)EFR32BG22 has up to 26 General Purpose Input/Output pins. Each GPIO pin can be individually configured as either an output or input. More advanced configurations including open-drain, open-source, and glitch-filtering can be configured for each individual GPIO pin. The GPIO pins can be overridden by peripheral connections, like SPI communication. Each peripheral connection can be routed to several GPIO pins on the device. The input value of a GPIO pin can be routed through the Peripheral Reflex System to other peripher-als. The GPIO subsystem supports asynchronous external pin interrupts.All of the pins on ports A and port B are EM2 capable. These pins may be used by Low-Energy peripherals in EM2/3 and may also be used as EM2/3 pin wake-ups. Pins on ports C and D are latched/retained in their current state when entering EM2 until EM2 exit upon which internal peripherals could once again drive those pads.A few GPIOs also have EM4 wake functionality. These pins are listed in the Alternate Function Table.3.4 Clocking3.4.1 Clock Management Unit (CMU)The Clock Management Unit controls oscillators and clocks in the EFR32BG22. Individual enabling and disabling of clocks to all periph-eral modules is performed by the CMU. The CMU also controls enabling and configuration of the oscillators. A high degree of flexibility allows software to optimize energy consumption in any specific application by minimizing power dissipation in unused peripherals and oscillators.3.4.2 Internal and External OscillatorsThe EFR32BG22 supports two crystal oscillators and fully integrates four RC oscillators, listed below.• A high frequency crystal oscillator (HFXO) with integrated load capacitors, tunable in small steps, provides a precise timing refer-ence for the MCU. The HFXO provides excellent RF clocking performance using a 38.4 MHz crystal. The HFXO can also support an external clock source such as a TCXO for applications that require an extremely accurate clock frequency over temperature.• A 32.768 kHz crystal oscillator (LFXO) provides an accurate timing reference for low energy modes.•An integrated high frequency RC oscillator (HFRCO) is available for the MCU system, when crystal accuracy is not required. The HFRCO employs fast start-up at minimal energy consumption combined with a wide frequency range, from 1 MHz to 76.8 MHz.•An integrated fast start-up RC oscillator (FSRCO) that runs at a fixed 20 MHz•An integrated low frequency 32.768 kHz RC oscillator (LFRCO) for low power operation without an external crystal. Precision mode enables periodic recalibration against the 38.4 MHz HFXO crystal to improve accuracy to +/- 500 ppm, suitable for BLE sleep inter-val timing.•An integrated ultra-low frequency 1 kHz RC oscillator (ULFRCO) is available to provide a timing reference at the lowest energy con-sumption in low energy modes.3.5 Counters/Timers and PWM3.5.1 Timer/Counter (TIMER)TIMER peripherals keep track of timing, count events, generate PWM outputs and trigger timed actions in other peripherals through the Peripheral Reflex System (PRS). The core of each TIMER is a 16-bit or 32-bit counter with up to 3 compare/capture channels. Each channel is configurable in one of three modes. In capture mode, the counter state is stored in a buffer at a selected input event. In compare mode, the channel output reflects the comparison of the counter to a programmed threshold value. In PWM mode, the TIMER supports generation of pulse-width modulation (PWM) outputs of arbitrary waveforms defined by the sequence of values written to the compare registers. In addition some timers offer dead-time insertion.See 3.13 Configuration Summary for information on the feature set of each timer.3.5.2 Low Energy Timer (LETIMER)The unique LETIMER is a 24-bit timer that is available in energy mode EM0 Active, EM1 Sleep, EM2 Deep Sleep, and EM3 Stop. This allows it to be used for timing and output generation when most of the device is powered down, allowing simple tasks to be performed while the power consumption of the system is kept at an absolute minimum. The LETIMER can be used to output a variety of wave-forms with minimal software intervention. The LETIMER is connected to the Peripheral Reflex System (PRS), and can be configured to start counting on compare matches from other peripherals such as the Real Time Clock.3.5.3 Real Time Clock with Capture (RTCC)The Real Time Clock with Capture (RTCC) is a 32-bit counter providing timekeeping down to EM3. The RTCC can be clocked by any of the on-board low-frequency oscillators, and it is capable of providing system wake-up at user defined intervals.A secondary RTC is used by the RF protocol stack for event scheduling, leaving the primary RTCC block available exclusively for appli-cation software.3.5.4 Back-Up Real Time Counter (BURTC)The Back-Up Real Time Counter (BURTC) is a 32-bit counter providing timekeeping in all energy modes, including EM4. The BURTC can be clocked by any of the on-board low-frequency oscillators, and it is capable of providing system wake-up at user-defined inter-vals.3.5.5 Watchdog Timer (WDOG)The watchdog timer can act both as an independent watchdog or as a watchdog synchronous with the CPU clock. It has windowed monitoring capabilities, and can generate a reset or different interrupts depending on the failure mode of the system. The watchdog can also monitor autonomous systems driven by the Peripheral Reflex System (PRS).3.6 Communications and Other Digital Peripherals3.6.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART)The Universal Synchronous/Asynchronous Receiver/Transmitter is a flexible serial I/O module. It supports full duplex asynchronous UART communication with hardware flow control as well as RS-485, SPI, MicroWire and 3-wire. It can also interface with devices sup-porting:•ISO7816 SmartCards•IrDA•I2S3.6.2 Enhanced Universal Asynchronous Receiver/Transmitter (EUART)The Enhanced Universal Asynchronous Receiver/Transmitter supports full duplex asynchronous UART communication with hardware flow control, RS-485 and IrDA support. In EM0 and EM1 the EUART provides a high-speed, buffered communication interface.When routed to GPIO ports A or B, the EUART may also be used in a low-energy mode and operate in EM2. A 32.768 kHz clock source allows full duplex UART communication up to 9600 baud.3.6.3 Inter-Integrated Circuit Interface (I2C)The I2C module provides an interface between the MCU and a serial I2C bus. It is capable of acting as a main or secondary interface and supports multi-drop buses. Standard-mode, fast-mode and fast-mode plus speeds are supported, allowing transmission rates from 10 kbit/s up to 1 Mbit/s. Bus arbitration and timeouts are also available, allowing implementation of an SMBus-compliant system. The interface provided to software by the I2C module allows precise timing control of the transmission process and highly automated trans-fers. Automatic recognition of addresses is provided in active and low energy modes. Note that not all instances of I2C are available in all energy modes.3.6.4 Peripheral Reflex System (PRS)The Peripheral Reflex System provides a communication network between different peripheral modules without software involvement. Peripheral modules producing Reflex signals are called producers. The PRS routes Reflex signals from producers to consumer periph-erals which in turn perform actions in response. Edge triggers and other functionality such as simple logic operations (AND, OR, NOT) can be applied by the PRS to the signals. The PRS allows peripherals to act autonomously without waking the MCU core, saving power.3.6.5 Pulse Density Modulation (PDM) InterfaceThe PDM module provides a serial interface and decimation filter for Pulse Density Modulation (PDM) microphones, isolated Sigma-delta ADCs, digital sensors and other PDM or sigma delta bit stream peripherals. A programmable Cascaded Integrator Comb (CIC) filter is used to decimate the incoming bit streams. PDM supports stereo or mono input data and DMA transfer.3.7 Security FeaturesThe following security features are available on the EFR32BG22:•Secure Boot with Root of Trust and Secure Loader (RTSL)•Cryptographic Accelerator•True Random Number Generator (TRNG)•Secure Debug with Lock/Unlock3.7.1 Secure Boot with Root of Trust and Secure Loader (RTSL)The Secure Boot with RTSL authenticates a chain of trusted firmware that begins from an immutable memory (ROM).It prevents malware injection, prevents rollback, ensures that only authentic firmware is executed and protects Over The Air updates. More information on this feature can be found in the Application Note AN1218: Series 2 Secure Boot with RTSL.3.7.2 Cryptographic AcceleratorThe Cryptographic Accelerator is an autonomous hardware accelerator which supports AES encryption and decryption with 128/192/256-bit keys, Elliptic Curve Cryptography (ECC) to support public key operations and hashes.Supported block cipher modes of operation for AES include:•ECB (Electronic Code Book)•CTR (Counter Mode)•CBC (Cipher Block Chaining)•CFB (Cipher Feedback)•GCM (Galois Counter Mode)•CBC-MAC (Cipher Block Chaining Message Authentication Code)•GMAC (Galois Message Authentication Code)•CCM (Counter with CBC-MAC)The Cryptographic Accelerator accelerates Elliptical Curve Cryptography and supports the NIST (National Institute of Standards and Technology) recommended curves including P-192 and P-256 for ECDH(Elliptic Curve Diffie-Hellman) key derivation and ECDSA (El-liptic Curve Digital Signature Algorithm) sign and verify operations.Supported hashes include SHA-1, SHA2/224, and SHA-2/256.This implementation provides a fast and energy efficient solution to state of the art cryptographic needs.3.7.3 True Random Number GeneratorThe True Random Number Generator module is a non-deterministic random number generator that harvests entropy from a thermal energy source. It includes start-up health tests for the entropy source as required by NIST SP800-90B and AIS-31 as well as online health tests required for NIST SP800-90C.The TRNG is suitable for periodically generating entropy to seed an approved pseudo random number generator.3.7.4 Secure Debug with Lock/UnlockFor obvious security reasons, it is critical for a product to have its debug interface locked before being released in the field.In addition, the EFR32BG22 also provides a secure debug unlock function that allows authenticated access based on public key cryp-tography. This functionality is particularly useful for supporting failure analysis while maintaining confidentiality of IP and sensitive end-user data.More information on this feature can be found in the Application Note AN1190: EFR32xG2x Secure Debug.3.8 Analog3.8.1 Analog to Digital Converter (IADC)The IADC is a hybrid architecture combining techniques from both SAR and Delta-Sigma style converters. It has a resolution of 12 bits at 1 Msps and 16 bits at up to 76.9 ksps. Hardware oversampling reduces system-level noise over multiple front-end samples. The IADC includes integrated voltage reference options. Inputs are selectable from a wide range of sources, including pins configurable as either single-ended or differential.3.9 PowerThe EFR32BG22 has an Energy Management Unit (EMU) and efficient integrated regulators to generate internal supply voltages. Only a single external supply voltage is required, from which all internal voltages are created. An optional integrated DC-DC buck regulator can be utilized to further reduce the current consumption. The DC-DC regulator requires one external inductor and one external capaci-tor.The EFR32BG22 device family includes support for internal supply voltage scaling, as well as two different power domains groups for peripherals. These enhancements allow for further supply current reductions and lower overall power consumption.3.9.1 Energy Management Unit (EMU)The Energy Management Unit manages transitions of energy modes in the device. Each energy mode defines which peripherals and features are available and the amount of current the device consumes. The EMU can also be used to implement system-wide voltage scaling and turn off the power to unused RAM blocks to optimize the energy consumption in the target application. The DC-DC regula-tor operation is tightly integrated with the EMU.3.9.2 Voltage ScalingThe EFR32BG22 supports supply voltage scaling for the LDO powering DECOUPLE, with independent selections for EM0 / EM1 and EM2 / EM3. Voltage scaling helps to optimize the energy efficiency of the system by operating at lower voltages when possible. The EM0 / EM1 voltage scaling level defaults to VSCALE2, which allows the core to operate in active mode at full speed. The intermediate level, VSCALE1, allows operation in EM0 and EM1 at up to 40 MHz. The lowest level, VSCALE0, can be used to conserve power fur-ther in EM2 and EM3. The EMU will automatically switch the target voltage scaling level when transitioning between energy modes.3.9.3 DC-DC ConverterThe DC-DC buck converter covers a wide range of load currents, provides high efficiency in energy modes EM0, EM1, EM2 and EM3, and can supply up to 60 mA for device and radio operation. RF noise mitigation allows operation of the DC-DC converter without signifi-cantly degrading sensitivity of radio components. An on-chip supply-monitor signals when the supply voltage is low to allow bypass of the regulator via programmable software interrupt. It employs soft switching at boot and DCDC regulating-to-bypass transitions to limit the max supply slew-rate and mitigate inrush current.3.9.4 Power DomainsThe EFR32BG22 has three peripheral power domains for operation in EM2 and EM3, as well as the ability to selectively retain configu-rations for EM0/EM1 peripherals. A small set of peripherals always remain powered on in EM2 and EM3, including all peripherals which are available in EM4. If all of the peripherals in PD0B or PD0C are configured as unused, that power domain will be powered off in EM2 or EM3, reducing the overall current consumption of the device. Likewise, if the application can tolerate the setup time to re-configure used EM0/EM1 peripherals on wake, register retention for these peripherals can be disabled to further reduce the EM2 or EM3 current.Table 3.1. Peripheral Power Subdomains。
电梯产品数据表
表2 电梯产品数据表（适用于自动扶梯与自动人行道）
产品品种
产品名称
名义速度
m/s
倾角
°
名义宽度
提升高度或使用区段长度
(自动扶梯或自动人行道) m
工作环境
工作类型
（公共交通型或普通型）
驱动
主机
型号
产品编号
额定转速
r/min
额定功率
kW
制造单位
控制柜
型号
节能运行方式
产品编号
制造单位
液压泵站
满载工作压力
MPa (适用于液压驱动电梯)
悬挂
系统
悬挂介质种类
钢丝绳、复合带等
悬挂介质数量
悬挂介质型号
悬挂介质规格
名称
型号
产品编号
制造单位
驱动主机
控制柜
限速器
安全钳
轿厢缓冲器
对重缓冲器
层门门锁装置
轿门门锁装置
/
上行超速保护装置
/
轿厢意外移动
保护装置
液压泵站
(适用于液压驱动电梯)
限速切断阀
(适用于液压驱动
电梯产品数据表
表1 电梯产品数据表（自动扶梯与自动人行道除外）
产品品种
产品名称
出厂编号
出厂日期
产品型号
额定速度
上行： m/s 下行： m/s
额定载重量
kg
轿厢尺寸
mm
提升高度
m
层/站/门数
/ /
防爆型式
(适用于防爆电梯)
防爆等级
(适用于防爆电梯)
驱动主机
额定功率
kW
额定转速
r/min
减速比
(适用于有齿减速)
天然气槽车产品数据表
天然气槽车产品数据表摘要：一、天然气槽车概述二、天然气槽车产品数据表主要参数1.容积2.质量3.最大载气量4.压力5.温度6.安全设施三、天然气槽车的应用领域四、选购与使用注意事项五、我国天然气槽车行业现状及发展趋势正文：一、天然气槽车概述天然气槽车是一种专门用于运输天然气的特种车辆。
它具有环保、高效、安全等优点，广泛应用于燃气行业、能源行业以及其他需要运输天然气的领域。
天然气槽车不仅有助于减少环境污染，还能降低运输成本，提高运输效率。
二、天然气槽车产品数据表主要参数1.容积：天然气槽车的容积通常在10立方米至50立方米之间，根据客户需求和运输场景进行选择。
2.质量：天然气槽车的质量主要包括车身质量、罐体质量、设备质量等。
车身质量取决于底盘类型和生产工艺，罐体质量则与罐体材料、厚度等因素有关。
3.最大载气量：天然气槽车的最大载气量是指在规定条件下，车辆所能承载的天然气总量。
最大载气量与容积、压力、温度等因素密切相关。
4.压力：天然气槽车的压力分为设计压力和实际工作压力。
设计压力是指罐体在正常使用条件下所承受的压力，实际工作压力则根据运输过程中的气体状态变化而调整。
5.温度：天然气槽车的温度分为设计温度和实际运输过程中的温度。
设计温度是指天然气在槽车内储存时的温度，实际运输过程中的温度受外部环境因素影响。
6.安全设施：天然气槽车配备有泄漏检测装置、温度监测装置、压力监测装置等安全设施，确保运输过程中的安全。
三、天然气槽车的应用领域天然气槽车广泛应用于燃气公司、液化天然气厂、石油化工企业、气体储存基地等领域，为我国的能源供应和环保事业做出了重要贡献。
四、选购与使用注意事项1.选购时，要根据实际需求选择合适的天然气槽车，如容积、压力、温度等参数。
2.使用前，要确保天然气槽车经过严格的检验和验收，确保其安全性能。
3.在运输过程中，要严格遵守相关规定和操作规程，确保天然气槽车的安全运行。
4.定期对天然气槽车进行维护和检查，确保设备处于良好状态。
钢铁产品材料安全数据表(MSDS)
文件版本号：B00482 首次发布日期：2005-7-18
第1部分 产品概述
产品名称：取向硅钢产品 CAS号码: 混合物/无CAS号 公司名称：宝山钢铁股份有限公司 地址：上海市宝山区同济路1800号 邮政编码：201900 联系方式：（白天） 电话：021-26643808， 传真：021-26645299 紧急情况联系方式：（24小时）8008208590
修改日期：2011-5-10
第2部分 主要组成成分与性状
名称成分 基板 铁 合金元素 铝
锑 碳
锰 磷
硅
硫
锡
CAS 号
7439-89-6
7429-90-5 7440-36-0 7440-44-0 7439-96-5 8049-19-2 7440-21-3 7704-34-9 7440-31-5
重量百分比％
铌，铅，锡，钼，硅和锆等。
1OSHA允许暴露极限 (PELs)一般是指8小时TWA (按时间平均的)浓度。C代号表示最大极限，一般情 况下不允许超过，STEL表示为15分钟暴露的极限，在工作中的任何时间均不得超过。 2TLV表示门槛极限值：它由美国工业卫生协会(ACGIH)规定。它表示是8小时的TWA。 3PNOR(未明确规定的颗粒物)：指所有惰性或中性的粉尘，可能是矿物质的，无机物或有机物，并未按 物质名称特别列入的ACGIH所规定的目录的，均归入PNOR。粉尘中无机物的暴露极限为15 mg/m3， 可吸入部分极限为5 mg/m3。 4吸入部分：对可吸入颗粒浓度的确定，是按照ACGIH TLVs 和BEIs附录D, 章节A的规定。 5PNOS (不另行规定的颗粒)：被列为PNOS的颗粒物是“恼人的灰尘”，不包含石棉，浓度应小于1%。 6吸入部分：对此可吸入部分，适用的极限的确定，是按照ACGIH TLVs 和BEIs附录D, 章节C的规定。
电梯产品数据表(参考样式)
表1 电梯产品数据表
产品种
产品名称
出厂编号
出厂日期
产品型号
额定速度
上行：m/s下行：m/s
额定载重量
kg
轿厢尺寸
mm
提升高度
m
层/站/门数
//
防爆型式
(适用于防爆电梯)
防爆等级
(适用于防爆电梯)
驱动主机
额定功率
kW
额定转速
r/min
减速比
(适用于有齿减速)
液压泵站
满载工作压力
MPa (适用于液压驱动电梯)
悬挂
系统
悬挂介质种类
钢丝绳、复合带等
悬挂介质数量
悬挂介质型号
悬挂介质规格
名称
型号
产品编号
制造单位
驱动主机
控制柜
限速器
安全钳
轿厢缓冲器
对重缓冲器
层门门锁装置
轿门门锁装置
/
上行超速保护装置
/
轿厢意外移动
保护装置
液压泵站
(适用于液压驱动电梯)
限速切断阀
(适用于液压驱动
电梯)
表2
产品品种
产品名称
名义速度
m/s
倾斜角
°
名义宽度
提升高度或使用区段长度
(自动扶梯或自动人行道) m
工作环境
工作类型
（公共交通型或普通型）
驱动
主机
型号
产品编号
额定转速
r/min
额定功率
kW
制造单位
控制柜
型号
节能运行方式
产品编号
制造单位
产品安全数据表
包装组：n.a.
15、法规
根据化学品包装分类和危险品标签规定。
该产品标识如下：
危险等级：
n.a.
成分：
n.a.
R等级：
n.a.
S等级：
n.a.
其它等级：
n.a.
16、其它信息
使用者的工作条件超出了我们所知道的范畴，该MSDS数据是在我们现有的认知和当前的EEC条例及国家法规的基础上的。在未得到操作手册的情况下，除了第1节中的详细描述，该产品不能用作其它用途。
产品安全数据表
1、物质鉴别
产品细节
商品名称：絮凝剂9715
制造商/供货商：上海新珂复合材料有限公司
地址：号
邮编：201603
电话：，
传真：
2、成分/成分数据
根据危险品条例67/548/EEC中方法，该产品不含有危害健康的物质。
特性：
以水为基质，含有阳离子聚酰胺
CAS号惯用名.含量分类等级R等级
无
3、制备过程中的危险性鉴别
摄入：在任何吞服的情况下都需要立即就医。注意休息，不要催吐。
5、救火措施
适合的灭火剂
建议：CO2、灭火粉或水枪，遇大火用水枪或防酒精泡沫剂。
建议：无需特殊措施，因为火会产生烟雾，所以措施，可参照第7和第8节的保护措施。
环保措施：用吸附材料收集溢出物，如土、沙等。
空的容器需按政府规定处理。
14、运输
陆路运输按照ADR标准，铁路运输按照RID标准，海运按照IMDG标准，空运按照ICAO/IATA标准
ADR/RID等级：非危险品
运输文件名：n.a.
IMDG等级：n.a.UN Nr：n.a.
MFAG：n.a.
产品功能参数对比表格模板
产品功能参数对比表格模板 | 功能/参数 | 产品A | 产品B | 产品C |。
| :-------| :---| :---| :---|。
| 参数1 | 值 | 值 | 值 |。
| 参数2 | 值 | 值 | 值 |。
| 参数3 | 值 | 值 | 值 |。
| 参数4 | 值 | 值 | 值 |。
| 参数5 | 值 | 值 | 值 |。
| 参数6 | 值 | 值 | 值 |。
| 参数7 | 值 | 值 | 值 |。
| 参数8 | 值 | 值 | 值 |。
| 参数9 | 值 | 值 | 值 |。
| 参数10 | 值 | 值 | 值 |。
在这个模板中，你可以根据实际情况添加更多的参数列或产品行。
每个产品都有自己的功能参数，你可以在相应的单元格中填写每个产品的参数数值。
通过这个表格，你可以清晰地比较不同产品之间的功能差异。
除了功能参数，你还可以在表格中添加其他方面的对比，例如价格、尺寸、重量、材料等。
这样可以更全面地了解产品之间的差异，并帮助你做出更明智的决策。
希望这个模板对你有所帮助！如果你还有其他问题，请随时提问。
产品安全数据表
九、物理及化学性质 物质状态：液体 颜色：无色 pH 值：— 分解温度：— 自燃温度：294 ℃ 蒸气压：1.5 mmHg 密度：1.0302@20℃(水=1) 溶解度：与水互溶（部份分解）
形状：澄清状液体 气味：温和水果味 沸点/沸点范围：154.5 ℃ 闪火点：℉46 ℃ 测试方法：（）开杯（ˇ）闭杯 爆炸界限：1.5%@100℃~11.4% 蒸气密度：4.1（空气=1）
产品安全数据表
乳酸乙酯
一、物品资料 物品名称：乳酸乙酯 (ETHYL LACTATE) CAS No.： 97-64-3
二、成分辨识资料 纯物质： 中英文名称：乳酸乙酯.. (ETHYL LACTATE) 同义名称：Actylol、Acytol、Ethyl 2-hydroxypropionate、Ethyl alpha-hydroxypropionate、Ethyl lactate 化学文摘社登记号码（CAS No.）：97-64-3 危害物质成分（成分百分比）：100
16.除非调配区以耐火结构隔离，否则不要在贮存区进行调配工作。 17.使用经认可的易燃性液体贮存容器和调配设备。 18.不要将受污染的液体倒回原贮存容器。 19.容器要标示，不使用时保持紧密并避免受损。 储存： 1.贮存在阴凉、干燥、通风良好以及阳光无法直接照射的地方，远离热源、发火源及不兼容物。 2.贮存设备应以耐火材料构筑。 3 .地板应以不渗透性材料构筑以免自地板吸收。 4 .门口设斜坡或门坎或挖沟槽使泄漏物可排放至安全的地方。 5 .贮存区应标示清楚，无障碍物，并允许指定或受过训的人员进入。 6 .贮存区与工作区应分开；远离升降机、建筑物、房间出口或主要通道贮存。 7.贮存区附近应有适当的灭火器和清理溢漏设备。 8 .定期检查贮存容器是否破损或溢漏。 9.检查所有新进容器是否适当标示并无破损。 10 .限量贮存。 11.以兼容物质制成的贮存容器装溢漏物。 12.贮桶接地并与其它设备等电位连接。 13.贮存易燃液体的所有桶子应安装释压阀和真空释放阀。 14 .依化学品制造商或供货商所建议之贮存温度贮存，必要时可安装侦温警报器，以警示温度是否过高或过低。 15 .避免大量贮存于室内，尽可能贮存于隔离的防火建筑。 16.贮槽之排气管应加装灭焰器。 17.贮槽须为地面贮槽，底部整个区域应封住以防渗漏，周围须有能围堵整个容量之防液堤。
区域产品销售数据统计表Excel模板
数量
地区 数量总计 占比
100
华南
367
17%
59
华北
204
9%
60
华中180Fra bibliotek8%61
东北
71
3%
62
西南
133
6%
63
西北
135
6%
180
华东
300
14%
200
港澳台
400
18%
300
海外
375
17%
67
68
使用说明：
120 10
A:D列为数据输入区，
71
输入之后，数据总计自
72
120
动按地区进行汇总，并
地区 华南 华北 华中 东北 西南 西北 华东 港澳台 海外 华南 华北 华中 东北 西南 西北 华东 港澳台 海外 华南 华北
17%
区域产品销售数据统计表
城市
广州 北京 武汉 黑龙江 贵州 新疆 上海 香港 美国 深圳 天津 武汉 黑龙江 云南 甘肃 苏州 台湾 英国 珠海 北京
产品
空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调 空调
200
自动计算各个地区占比。
75
200
然后自动生成图表。
77
各地区数量总计
14%
18%
17%
9%
8%
6%
6%
3%
华南
海外 华东 西南 华中 华南
0
华北
华中
东北
西南
西北
华东
港澳台
海外
各地区数量总计
特种设备产品数据表(锅炉、压力容器、电梯、叉车等)
门式起重机产品数据表
编号:
塔式起重机产品数据表
编号:
流动式起重机产品数据表
编号:
门座式起重机产品数据表
编号:
升降机产品数据表
缆索式起重机产品数据表
编号:
桅杆式起重机产品数据表
编号:
机械式停车设备产品数据表
编号:
大型游乐设施产品数据表
编号:
注：乘客束缚装置包括安全带、安全压杠、安全档杆、柔性约束物等。
客运索道产品数据表
编号:
电梯产品数据表（自动扶梯与自动人行道除外）
电梯产品数据表（适用于自动扶梯与自动人行道）
车用气瓶产品数据表
编号:
锅炉产品数据表
编号:
注：本表的具体项目可以根据锅炉类别编制，主要受压部件只填写锅筒（锅壳）、过热器出口集箱、启动分离器。
其他有关数据应当在产品出厂资料其他要求的内容中提供。
压力容器产品数据表
编号:
场（厂）内专用机动车辆产品数据表
（叉车）
编号： __________________。