模具英文单词

Mould components & Accessories

Mould base 模胚Bolts 螺栓

Mould frame 模架screw 螺丝

Top clamp plate 面板Stripper screw 脱料螺丝

Bottom clamp plate底板 F.H.C. screw（flat head cap screw）平头螺丝Socket head sountersunk screws 平头螺丝

Hot runner plate 热流道板S.H.C. screw( socket head cap screw) 杯头螺丝Runner plate 水口板hexagonal socket head cap screw 杯头螺丝

A plate A板 Hexagonal head screw 六角头螺丝

B plate B板 Grub screw 无头螺丝（等高螺丝

，基米螺丝）

Stripper plate 推板Ball screw 波仔螺丝

Support plate 支撑板Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝）Spacer plate 方铁latch 插销

Ejector retainer plate 顶针面板baffle 隔水片

Ejector plate 顶针板plugs 喉塞

Insulating plate 隔热板Jiffy plugs 喉咀

Cavity 前模o-ring 密封圈

Cavity insert 前模镶件Cooling tube 散热管

Core 后模spring 弹簧

Core insert 后模Support pillar 撑头

Slide 行位Stop pin 垃圾钉

Slide insert 行位镶件Dowel pin 管钉

jaw 行位压块Spacer ring/washer 间隙圈

Slide wear plate 行位耐磨块Venting slots 排气槽

Slide guide block 行位导向块thermocouple 电热偶

Slide lock 行位锁/行位扣Thermocouple connector 接线盒

Wedge block 铲机Limit switch 限位开关

W.B. wear plate 铲机耐磨块probe 探针

Core pin 镶针Pry bar slots 开模槽

Angle pin 斜导柱Safety strap 模锁

Angle lifter 斜顶Lifting eye bolt 吊环（方向已固定）

Lifter guide block 斜顶导向块Hydraulic cylinder 油缸

Lifter base 斜顶座Air cylinder 气缸

Press block 模料挤紧块Hydraulic motor 马达

hoist ring 吊环（可转动方向）Knock out hole 顶棍孔

Parting lock 树脂开闭器（尼龙扣）

Name plate 铭牌Straight side interlocks T型锁（直身锁）

Date code 日期印Tapered interlocks 斜度锁

Cavity number 模穴号sensor 感应器

engrave 刻字/凹入heater 加热器

Raised out 凸出K.O. insert 顶棍孔镶件

Gate type & runner

Drop gate 点水口Sprue bushing 唧嘴

Pin point gate 细水口Sprue/gate 浇口

Edge/side gate 边水口

Center sprue/sprue gate 中心进胶/直浇口runner shut off 流道开关/转水口

Sub gate 潜水口Runner lock pin 水口扣针

Tunnel gate 隧道浇口Puller 拉钩

Ring gate 环形浇口Sprue lock pin 拉料杆

Fan gate 扇形浇口Slag well 冷料井

Valve gate 针阀式水口

Banana gate 香蕉水口

Guide＆Locating system

Guide pin/leader pin 导柱Grinder研磨机Crane 天车（吊车）

Guide bushes 导套Grinding machine 磨床 Groover machine 开槽机

locating ring 法兰Lathe machine 车床Radial drill摇臂钻床

EGB( ejector guide bush) 中托司Milling machine 铣床Wire cut machine 线割机Ejecting system

Ejector pin 顶针Gear 齿轮

Stepped ejector pin 有托顶针Rack 齿条

Blade ejector 扁顶针Bearing 轴承

Ejector bar 顶块Roller bearings 滚珠轴承

Sleeve 司筒Retraction spring 复位弹簧

Stripper plate 推板Return pin 回针

Unscrewing 脱螺纹Two-stage ejector 二次顶出

Ejector retainer plate 顶针面板chain 链条

Ejector plate 顶针板Chain wheel 链轮

Stop block 限位块key 键

Ejector bushes 顶针套

Specification of Injection Moulding Machine

Diameter of the location ring 法兰直径

Nozzle radius 机嘴半径

Nozzle injection hole diameter 机嘴注射孔直径

Depth for the nozzle into the mould 机嘴进入模具的深度

KO hole distance KO孔间距

fine thread 细螺纹

Rough thread 粗螺纹

mould opening distance 开模距离

mould thickness 模具厚度

tie bar distance Tie Bar 距离

Injection defects

flash 披锋Warpage/deformation 变形

Ejected mark 顶白Step 断差/台阶

Weld line 熔接线Short shots 短胶

Sink mark 缩水Sharp corner 尖角

Gas trapped 困气Sharp edge 尖边