中英文 检验规范指导书完整资料

NK-QC-C-13-9-1-3

日期:2014.05.17CR: 0 MA: 0.65 MI: 1.0

步骤steps

检验项目Inspection items

检验方法Inspection methods

Inspection frequency disadva ntages type

1.0

材质规格Material specifications 目视visual

first thing refuelin

MA

2.1表面异物

A foreign body surface

目视visual

5pcs/30min

MI

2.2

表面脏污

surface of the

dirt

目视visual

5pcs/30min MI

2.3

划伤和印痕Scratches and

marks.

目视visual 5pcs/30min

MI

2.4

牙孔Tooth hole 目视/牙规Visual/tooth

gauge

5pcs/30min

MA

2.5

变形压伤

Deformation of crushed

目视visual

5pcs/30min MI

3.0

尺寸

size

卡尺caliper 每批Each batch MA

3.1两侧折弯角度On both sides of the bending Angle

角度规gauge 5pcs/30min MI

4 抽牙孔Smoking tooth hole

卡尺caliper 5pcs/30min MI 5毛刺burr 目视visual

5pcs/30min MI

5.1

包装packaging

目视visual

5pcs/30min

MI

使用专用纸箱包装,外箱上须按客户要求标示

Use special carton packaging, on the outer cartons must be labeled according to customer's request

材质按客户样品要求 ，规格按图纸要求。

Material in accordance with the requirements of customer samples, specifications according to the drawing

requirements 因清洗中使用布擦，产品表面的布丝要求清除干净。Used for cleaning cloth, clean cloth wire on the surface of

the product requirements.按客户图纸要求公差范围内

According to customer requirements drawing tolerance range 压伤`变形目视明显不可接受。（平坦度超过1.0以上变形为不良）Visual apparent crushed ` deformation is not acceptable.

More than 1.0 above deformation is bad (flatness)规格及说明Specifications and instructions

攻牙孔毛刺不能刮手感。Tapping hole burrs cannot handle.不良图示Bad here

文件编号 file number 细微的污迹无手感为良品；小于Φ1.0以下5点以内为合格。 Minor stains without feel as good parts; Less than 1.0 Φ for qualified within the following 5 points.

5个部位，长度10厘米以上，看上去明显的不允许。Five parts,

more than 10 centimeters in length, apparently not allowed.

孔内金属废屑不可有手感,孔内 M2.6，M3`M5牙纹能通过牙规检测。

缺漏攻牙不可有。Hole metal scraps with handle, hole M2.6, M3 ` M5

tooth tattoo can pass the tooth gauge test.

You shall not have any missing tapping

1.孔无错位变形，

2.抽牙高度合格，拉升均匀

1) hole without displacement deformation, and (2) smoke

teeth are highly qualified, pull to rise evenly 90度直角正负1度，生产前QC进行组装实配。

90 - degree Angle of plus or minus 1 degree, real match

production QC before assembly.WANGYONG

核 对CHECK BY

AQL

通 用 检 验 规 范

General inspection specifications

机种model NESS

NK

Metal products co., LTD

制 作Initiated by