ACOPOS 贝加莱伺服出错代码表(1)

ACOPOS 出错代码表

1: 参数 ID 无效 Parameter ID invalid
2: 参数不可读 ( 变量不能在该时刻读取) Parameter can not be read (value is not available at the moment)
3: 对只读参数写访问 Write access for a read only parameter
4: 对只写参数读访问 Read access for a write only parameter
5: 参数数值无效 Value of parameter is invalid
(REAL): 变量格式 Info(REAL): Value of Parameter
6: 参数数值无效 Value of parameter is invalid
(UDINT): 变量格式 Info(UDINT): Value of Parameter
7: 参数数值无效 Value of parameter is invalid
(DINT): 变量格式 Info(DINT): Value of Parameter
8: 数据块读访问已经初始化 Data block read access already initialized
9: 数据块写访问已经初始化 Data block write access already initialized
10: 数据块读访问未初始化 Data block read access not initialized
11: 数据块写访问未初始化 Data block write access not initialized
12: 数据块读访问仍激活 ( 读访问初始化不可能)
Data block write access still active (INIT for read access not possible)
13: 数据块写访问仍激活（写访问初始化不可能）
Data block read access still active (INIT for write access not possible)
14: 读响应超时 Timeout for Read Response
15: 写响应超时 Timeout for Write Response
16: 数据块数据段在读已经在最后 The Data segment at data block read is already the last
17: 数据块数据段在写已经在最后 The Data segment at data block write is already the last
18: 数据块数据段未在读在最后 The Data segment at data block read is not yet the last
Info(UDINT): 数据块偏移 Data block offset
19: 数据段未在写数据块的最后
Info(UDINT): 数据块偏移 Data block offset
20: 数据块读后检验和无效 Checksum after data block read is invalid
21: 数据块写后检验和无效 Checksum after data block write is invalid
22: 参数 ID 在数据块中无效（读数据块） Parameter ID in data block is invalid (data block read)
Info('PARID'): Parameter ID
23: 参数 ID 在数据块中无效（写数据块） Parameter ID in data block is invalid (data block write)
Info('PARID'): Parameter ID
24: 在启动状态不允许下载系统模块 System module download not allowed in this boot state
Info(UINT): Boot state
25: 只在下载后允许立即烧结系统模块 Burn system module only allowed immediately after download
26: 在启动状态不允许改变启动状态请求 Requested change of boot state is not allowed in this boot state
Info(UINT): Boot state
27: 启动操作系统不可能（操作系统不在FPROM 存储器中）
Start of operating system not possible (operating system is not on the FPROM)
28: 在此驱动状态不允许读参数 Read parameter not allowed in this drive state
Info(UINT): Drive state
29: 在此驱动状态

不允许写参数 Write parameter not allowed in this drive state
Info(UINT): Drive state
30: 因为硬件故障不能读参数 Read parameter not possible because of hardware error
Info(UINT): Hardware error
31: 因为硬件故障不能写参数 Write parameter not possible because of hardware error
Info(UINT): Hardware error
32: 命令参数无效 Command parameter is invalid
Info('PARID'): Parameter ID


40: 参数数值大于最大值 Value of parameter higher than maximum value
Info(REAL): Maximum value
41: 参数数值大于最大值 Value of parameter higher than maximum value
Info(UDINT): Maximum value
42: 参数数值大于最大值 Value of parameter higher than maximum value
Info(DINT): Maximum value
43: 参数1 数值大于最大值 Value of parameter1 higher than maximum value
Info(REAL): Maximum value
44: 参数1 数值大于最大值 Value of parameter1 higher than maximum value
Info(UDINT): Maximum value
45: 参数1 数值大于最大值 Value of parameter1 higher than maximum value
Info(DINT): Maximum value
46: 参数2 数值大于最大值 Value of parameter2 higher than maximum value
Info(REAL): Maximum value
47: 参数2 数值大于最大值 Value of parameter2 higher than maximum value
Info(UDINT): Maximum value
48: 参数2 数值大于最大值 Value of parameter2 higher than maximum value
Info(DINT): Maximum value
49: 参数3 数值大于最大值 Value of parameter3 higher than maximum value
Info(REAL): Maximum value
50: 参数3 数值大于最大值 Value of parameter3 higher than maximum value
Info(UDINT): Maximum value
51: 参数3 数值大于最大值 Value of parameter3 higher than maximum value
Info(DINT): Maximum value
52: 参数数值小于最小值 Value of parameter lower than minimum value
Info(REAL): Minimum value
53: 参数数值小于最小值 Value of parameter lower than minimum value
Info(UDINT): Minimum value
54: 参数数值小于最小值 Value of parameter lower than minimum value
Info(DINT): Minimum value
55: 参数1 数值小于最小值 Value of parameter1 lower than minimum value
Info(REAL): Minimum value
56: 参数1 数值小于最小值 Value of parameter1 lower than minimum value
Info(UDINT): Minimum value
57: 参数1 数值小于最小值 Value of parameter1 lower than minimum value
Info(DINT): Minimum value
58: 参数2 数值小于最小值 Value of parameter2 lower than minimum value
Info(REAL): Minimum value
59: 参数2 数值小于最小值 Value of parameter2 lower than minimum value
Info(UDINT): Minimum value
60: 参数2 数值小于最小值 Value of parameter2 lower than minimum value
Info(DINT): Minimum value
61: 参数3 数值小于最小值 Value of parameter3 lower than minimum value
Info(REAL): Minimum value
62: 参数

3 数值小于最小值 Value of parameter3 lower than minimum value
Info(UDINT): Minimum value
63: 参数3 数值小于最小值 Value of parameter3 lower than minimum value
Info(DINT): Minimum value
64: 硬件ID 在B&R 模块中无效（数据块写） Hardware ID in B&R module is invalid (data block write)
Info(USINT): Hardware ID
65: 硬件版本在B&R 模块中无效（数据块写）
Hardware Version in B&R module is invalid (data block write)
Info(USINT): Hardware Revision
66: 硬件ID 的操作系统不兼容现在的总线网络
Hardware ID of operating system is incompatible to the existing network
Info(USINT): Hardware ID


1001: 数据先进先出溢出 Error FIFO overflow
1002: 参数超出有效范围 Parameter outside the valid range
1003: 在回路控制激活时不允许写参数 Writing parameter is not allowed during loop control is active
1004: 激活信号控制网络超时 Timeout in network live sign control
1005: 在动作激活时不允许写参数 Writing parameter is not allowed during a movement is active
1006: 用于触发事件（数字量输入+ 边沿）无效参数
Invalid parameter for trigger event (digital input + edge)
1007: 主站用于网络耦合未激活-一个主站已经发送
Master for network coupling deactivated - one master is already sending
1008: 主站用于网络耦合未激活-编码器错误 Master for network coupling deactivated - Encoder error
1009: 内存分配错误 Error on memory allocation
1010: 先进先出功能块溢出 Function FIFO overflow
1011: 快停输入激活 Quickstop input active
1012: 循环网络通信切断 Breakdown of cyclic network communication
1013: 用于网络通信的站点不可行 Station is not available for network communication
1014: AC112 命令接口占用 AC112 command interface is occupied
2001: 上载跟踪曲线数据不允许：记录激活 Upload of trace data not allowed: Recording active
2002: 无跟踪曲线数据可上载 No trace data available for upload
2003: 跟踪曲线启动不允许：记录激活 Trace start not allowed: Recording active
2004: 跟踪曲线启动不允许：未定义跟踪数据Trace start not allowed: No trace test data defined
2005: 无效的参数ID 用于跟踪测试数据 Invalid parameter ID for trace test data
Info('PARID'): Parameter ID
2006: 初始跟踪参数不允许：记录激活 Initialization of trace parameters not allowed: Recording active
4002: 在仿真命令无效的动作代码 Invalid action code in simulation command
4004: 在控制器命令无效的动作代码 Invalid action code in controller command
4005: 使能控制器无效：驱动器错误 Switch controller on not possible: Drive in error state
4007: 跟随误差超限停止 Lag error stop limit exceeded
Info(REAL): Current lag error
4008: 正限位开关到达 Positive limit switch r

eached
4009: 负限位开关到达 Negative limit switch reached
4010: 使能控制器无效：两限位关闭 Switch controller on not possible: Both limit switches are closed
4011: 关闭控制器无效：运动激活 Switch controller off not possible: Movement active
4012: 使能控制器无效：初始参数丢失或无效
Switch controller on not possible: Initial parameter missing or not valid
Info('PARID'): Parameter ID
4014: 双编码器控制：位置偏差超限停止 Two encoder control: Stop limit of positions difference exceeded
Info(REAL): Current positions difference
5001: 目标位置大于正向软限位 Target position > positive SW limit
5002: 目标位置小于负向软限位 Target position < negative SW limit
5003: 正向软限位到达 Positive SW limit reached
5004: 负向软限位到达 Negative SW limit reached
5005: 运动启动不可能：位置控制器未激活 Start of movement not possible: Position controller inactive
5006: 运动启动不可能：轴未寻参考位置 Start of movement not possible: Axis not referenced
5010: 正向位置运动不可能：正向限位开关关闭
Move in pos. direction not possible: Pos. limit switch is closed
5011: 负向位置运动不可能：负向限位开关关闭
Move in neg. direction not possible: Neg. limit switch is closed
5012: 运动启动不可能：停止激活 S