中英文电池充电器测试报告

提交日期

型号

电池零件号

充电器零件号 Charger Part#

序列号

电池类型

充电器类型

检测组件

Component Being

电池电流

充电器电流

Charger Amps

充电器样式

描述

Description

检测员 热电偶位置

Thermal Couple Location 室温

Ambient Temperature

检测站

Station 提供手册？

Manual Provided?

阅览手册？

Manual Reviewed?

报告日期

Report Date

第三方实验室测试? Tested by a 3rd party lab?

IEC60335-29 或 IEC60601-1 报告

引用电池组

Reference Batteries Set 如果是，请说明依照标准

If so, to what standard?

附件

Attachment

保护装置

Protection Device

漏电流不得超过0.1毫安。

Leakage current should not exceed 0.1mA.

认证类型

Type of Certifications

测试结果 TEST RESULTS

最大电压

Max Voltage 充电周期

Charge Cycle 浮动电压

Float Voltage

充电周期

Charge Cycle

最大电流

Max Current 充电周期

Charge Cycle

浮动电流

Float Current 充电周期

Charge Cycle

最大外壳温度

Max Case Temp 室温应小于：

塑料35K+ ，金属25K+

Should be less than:

35K+ Ambient for plastic;

25K+Amebient for metal

充电周期

Charge Cycle

充电至80%容量

80% Capacity Reached 评论

显示结果

检测技术员

Test Technician 日期

Date

审阅人

Reviewer 日期

Date

电池/充电器参考资料（容量，C/5等级，等等）REFERENCE BATTIERY/CHARGER INFORMATION (CAPACITY, C/5 RATING, etc.)

样品编号

NUMBER OF SAMPLES

使用装置

DEVICE TO BE USED IN

电池是否标明生产厂家？

IS THE BATTERY MARKED WITH THE MANUFACTURER?

电池是否标明类型（AGM,胶体）？

IS THE BATTERY MARKED WITH THE TYPE(AGM,GEL)?

电池是否标明额定电压？

IS THE BATTERY MARKED WITH THE NOMINAL VOLTAGE?

电池是否标明额定容量（C20和C5）？

IS THE BATTERY MARKED WITH THE RATED CAPACITIES (C20 AND C5)?

电池是否标明生产日期？

(IS THE BATTERY MARKED WITH THE DATE OF MANUFACTURE?)

电池相邻端子是否标明极性？

IS THE BATTERY MARKED WITH THE POLARITY MARKINGS ADJACENT

TO EACH TERMINAL?

参考文献

(References)

1.RESNA 7176

2.IEC 60335-1

3.IEC 60335-2-29

4.IEC 60601-1

5.IEC 529

合格/不合格

Pass/Fail

分析清单

PROFILING CHECKLIST

如果充电器反极性连接，不应有大于100毫安的电流流动，也不

会损坏充电器。（依照ANSI/RESNA7176第14章9.2.5）Array IF THE CHARGER IS CONNECTED IN REVERSE POLARITY NO MORE THAN

100mAOF CURRENT SHOULD FLOW, NOR SHOULD ANY DAMAGE OCCUR. (AS

PERANSI/RESNA 7176 SECTION 14 CLAUSE 9.2.5)

在电流不足或超负荷情况下，充电器不会受到损坏，过电流也不Array会流动。

CHARGER SHOULD NOT BE DAMAGED AND EXCESSIVE CURRENT SHOULD NOT

FLOW DURING SHORT AND OVERLOAD CONDITIONS.

尚未安装或准备安装在轮椅上的电池充电器应当符合IEC60335-29

的要求，还应达到IEC529-IPX1的防潮要求（防滴）。

ARE INTENDED FOR WHEELCHAIR BATTERIES SHALL MEET THE REQUIREMENTS

OF CLASS 2 OF IEC 60335-2-29 AND SHALL BE MOISTURE RESISTANT TO IEC 529-

IPX1 (DRIP PROOF).