油溶性破乳剂

没油溶性破乳剂

∙gujchem的osd完全是一种有机液体制定的表面活性剂和分散剂在水和易溶于甲苯，二甲苯，芳烃溶剂，原油破乳的油包水和水包油。

∙gujchem的osd能力表现在室温下，但提高速度和百分比的石油拆除时，适用于气温接近60度。商业（140 ℃下六）。

∙gujchem的osd破坏了油水界面，禁止各水粒子在乳液中，它将取代现有的乳化剂分子（如果有的话），并允许水凝聚。

∙gujchem osd公司是一个完全可燃，不耐磨，不灰成形治疗这将有利于提高质量，燃料，它是补充。

特点：

外表：均相液体

密度：0.9 + -0 .5

溶解度：甲苯，二甲苯，原油，芳烃溶剂

ph范围：6.5至8.0

易溶于水：色散

优点：

•不留在水相，因此，没有贡献水污染

•停留与燃料和实际上提高了燃烧特性的燃料

•使用较低剂量比大多数竞争产品

剂量：

由于各种不同性质的油和废物可以通过治疗gujchem osd公司，具体建议都必须作出关于在个案

的基础上。用量gujchem的osd明，打破了，特别是乳液的不同，从少1加仑每20000加仑（50 ppm ）的石油多达1加仑每万加仑（100 ppm ）的石油。少数客户甚至发现，20个百万分之，是更为有效的较高剂量，因此，我们建议加入，下级向你的实验台测试，以验证正确的剂量，为

具体应用。找出最符合成本效益的剂量，以及确定的最佳条件温度，缓慢搅拌，结算时间等，是最

好做的，在实验室里，用抽样调查的实际石油或浪费和样本gujchem的osd

应用系统：

一旦你确定了正确的剂量gujchem的osd ，填补坦克与废物-石油-水溶液注入正确的剂量gujchem osd公司直接从鼓。调匀，随着援助的一个水泵，为4时58个小时。混合时间的长

短视乎大小的坦克和速度的汽车。允许燃料来解决，并检查水分离。视配置的坦克，无论是消

除水的方式外流，在底层或吸吮干净石油小康，从最高层的智囊团。

包装和处理：

gujchem的osd是装在55加仑低碳钢桶（208公升），它包含了啊芳烃溶剂，并应妥善处理，

容易半技术工人。

注：以上gujchem范围运行的产品。我们可以生产较高痣对客户的具体需求和规格，可

以被修改为每位顾客的要求。

OIL SOLUBLE DEMULSIFIER

∙GUJCHEM OSD is a totally organic liquid formulation of surfactants and dispersants in

a water and soluble in toluene ,Xylene, Aromatic solvent, crude oil for the

demulsification of water in oil and oil in water.

∙GUJCHEM OSD capable of performance at room temperature, but with improved speed and percentage of oil removed when applied at temperatures near 60 deg. C (140 deg. F).

∙GUJCHEM OSD destabilizes the oil-water interface that surrounds each water particle in the emulsion, replaces the emulsifier molecules(if any), and allows the water to coalesce.

∙GUJCHEM OSD is a completely combustible, non-abrasive, non-ash-forming treatment which will improve the quality of the fuel it is added too.

CHARACTERISTICS :

Physical Appearance: Homogenous Liquid

Density: 0.9 +- 0.5

Solubility: Toluene,xylene,crude oil, aromatic solvent

PH range: 6.5 to 8.0

Soluble in water: Dispersion

ADVANTAGES :

• Does not stay with the water phase, therefore does not contribute to water pollution • Stays with the fuel and actually improves burning characteristics of the fuel

• Uses lower dosages than most competing pr oducts

DOSAGE :

Because of the diverse nature of oil and waste amenable to treatment with GUJCHEM OSD, specific recommendations have to be made on a case-by-case basis. The dosage of GUJCHEM OSD prescribed to break a particular emulsion varies from as little as 1 gallon per 20,000 gallons (50 ppm) of oil to as much as 1 gallon per 10,000 gallons (100 ppm) of oil. A few clients have even found that 20 ppm was more effective than the higher dosages, so we suggest adding the lower levels to your laboratory bench tests to verify the correct dosage for the specific application. Finding the most cost-effective dosage, as well as determining the best conditions of temperature, slow mixing, settling time, etc., is best done in the laboratory, using a sample of the actual oil or waste and a sample of GUJCHEM OSD

APPLICATION :

Once you have determined the correct dose of GUJCHEM OSD, fill the tank with the waste-oil-water solution and inject the correct dose of GUJCHEM OSD directly from the drum. Mix thoroughly, with the assistance of a pump, for two to five hours. Mixing time varies depending on the size of the tank and the speed of the motor. Allow the fuel to settle and check for water separation. Depending on the configuration of the tank, either remove the water by means of a drain in the bottom or suck the clean oil off from the top of the tank.

PACKAGING AND HANDLING :

GUJCHEM OSD is packaged in 55 gallon mild steel drums (208 liters) It contains a h aromatic solvent, and should be handled easily semi skilled workers.

Note: Above Gujchem Range are the running products. We can produce higher moles on customer specific demand and specifications can be altered as per customer requirement.

AAAAA