注塑机专业英语
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
注塑机专业英语 Company number：【WTUT-WT88Y-W8BBGB-BWYTT-19998】
钣金 machine cover / upper cover/ side cover 锁模部分 clamping unit
射胶部分 injection unit
机架 machine frame / base
电气系统 electric system
液压系统 hydraulic system
机械系统 mechanical system
机门 safety door / fixed door / movable door 锁模部分 clamping unit
电脑控制器 computer controller
机械安全锁 mechanical safety interlock
射胶部分 injection unit
液压系统 hydraulic system
电箱 electrical cabinet / cable
机架分体线 stand split line
机架螺丝孔 foundation bolt hole
机架 machine base / supporting frame
理论注射容积 theoretical shot volume
实际注射量 shot weight
螺杆直径 screw diameter
注射压力 injection pressure
注射速度 injection speed
注射速率 injection rate
螺杆长径比 screw L/D ratio
螺杆行程 screw stroke
螺杆转速 screw speed
熔胶能力 plasticizing capacity
锁模力 clamping force
开模/锁模行程 mold clamping / opening stroke 模板尺寸 platen size
拉杆间距 distance between tie bars / rods
模板最大距离 max. daylight
容模量 mold thickness (min. & max.)
顶出行程 hydraulic ejection stroke
顶出力 hydraulic ejection force
顶针数 nos. of ejector pin
液压系统压力 hydraulic system pressure
油泵马达 pump motor
电热量 heating capacity
温度控制区数 nos. of temp control zones
射嘴接触力 nozzle contact force
Injection射出
Cooling time 冷却时间
Holding time 锁模时间
Injection alarm time 射出警报时间
Injection start delay
Final cushion minimum value
Change-over to holding by value
Plasticizing end value
Hydrarlic change-over pressure holding Screwvalue for change-over to holding
Change-over to holding by enable value
Hydraulic pressure in holding 锁模压力
Filling stage pressure limit
Injection speed 射出速度
Injection注射
Cooling time冷却时间
Holding time
Injection alarm time注射报警时间
Injection start delay注射开始延时
Final cushion minimum value最后段位置
Change-over to holding by value切换到锁模Plasticizing end value预塑重终点
Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Change-over to holding by enable value
Hydraulic pressure in holding锁模力
Filling stage pressure limit充模压力
Injection speed注射速度
Plasticizing delay预塑延时
1st suck-back speed储料一速度
1st suck-back pressure储料一压力
Screwrotation speed螺杆转速
Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould closing关模
Mould close force关模压力
Mould closing safety time.. 时间
Mould closing pressure.. 压力
1st closing safety stage pressure合模一段压力
1st mould closing speed ...成型速度
1st stage mould closing speed
1st stage mould closing safety position.....位置High pressure start position高压锁模位置
Number of repeat mould closing movement..重复次数Holding time 保压时间
Injection start delay 注射延迟
Injection注射
Cooling time冷却时间
Holding time保压时间