PCB基本英语
PCB工程部专业英语词汇
PCB 工程部专业英文词汇词汇1.板料: material2.最低限度: minimum 或者min.3.最大限度: maximum 或者max.4.基准点(零点) datum point5.周期Date code6.V-cut余厚V-cut remain thickness7.抢电铜皮（假铜）dummy copper8.实物板actual board9.外形及尺寸错误dimension error10.异常情形error data file11.焊锡面与零件面对位偏差misregistration12.孔塞plug hole13.要求requirement14.缺少miss15.偏公差uneven tolerance16.补偿compensation17.表面处理surface treatment18.无铅喷锡Lead free HAL19.金手指斜边bevel of G/F20.制程能力process capability21.建议,暗示suggest22.确保ensure23.满足,达到meet24.为了in order to25.交货期delivery date26.绿油桥solder mask bridge 或者solder mask dam27.根据according to28.单边3mil per side 3 mil29.直径diameter30.半径radius 31.小于3mil less than 3mil32.高于3mil more than 3 mil33.压合结构stacking structure 或者stack_up34.附件：attached file35.样品：sample36.文档：Document37.答复：answer; reply38.规格：spec39.与...同样的：the same as40.前版本：previous version(old version)41.生产：production42.确认：confirm43.再次确认：confirm again44.工程问题：engineering query（EQ）45.尽快：as soon as possible46.生产文件：production Gerber47.联系某人：contact somebody48.提交样板：submit sample49.交货期：delivery date50.电测成本：ET（electrical test）cost51.通断测试：Open and short testing52.参考：refer to53.IPC标准：IPC standard54.IPC二级：IPC class 255.可接受的：acceptable56.允许：permit57.制造：manufacture 或者fabricate58.修改：revision59.公差：tolerance60.忽略：ignore61.工具孔：tooling hole62.安装孔：mounting hole63.元件孔：component hole64.槽孔：slot hole65.邮票孔：snap off hole 或者stamp hole66.导通孔：via hole67.盲孔：blind via hole68.埋孔：buried via hole69.金属化孔：PTH(plated through hole)70.非金属化孔：NPTH( no plated through hole)71.孔位：hole location72.避免：avoid73.原设计：original design74.修改：modify75.按原设计：follow up original design76.附边：waste tab, waste area 或者breakaway tab77.铜条：copper strip78.拼板：panel drawing79.板厚：board thickness80.删除：remove(delete)81.削铜：shave the copper82.露铜：copper exposure 或者exposed copper83.光标点: fiducial mark84.不同：be different from(differ from)85.内弧：inside radius86.焊环：annular ring87.单板尺寸：single size88.拼板尺寸：panel size89.铣,锣：routing90.铣刀：router 或者Routing bit91.楔形掏槽V-cut 或者V scoring92.哑光：matt93.光亮的：glossy94.锡珠：solder ball(solder plugs)95.阻焊：solder mask(solder resist)96.阻焊开窗：solder mask opening 97.单面开窗：single side mask opening98.补油：touch up solder mask99.补线：track welds100.毛刺：burrs101.去毛刺：deburr102.镀层厚度：plating thickness103.清洁度：cleanliness104.离子污染：ionic contamination105.阻燃性等级：flammability retardant rating 106.黑化：black oxidation107.棕化：brown oxidation108.红化：red oxidation109.可焊性不良：poor solderability110.焊料：solder111.包装：packaging112.角标：corner mark113.特性阻抗：characteristic impedance 114.正像：positive115.负片：negative116.镜像：mirror117.线宽：line width 或者trace width118.线距：line spacing 或者trace spacing 119.做样：build sample120.按照：according to121.成品：finished122.做变更：make the change123.相类似：similar to124.规格：specification125.下移：shift down126.垂直地：vertically127.水平的：horizontally128.增大：increase129.缩小：decrease130.表面处理：Surface Finishing131.波峰焊：wave solder132.钻孔数据：drilling data133.标记：Logo134.Ul 标记：UL logo,或者Ul Marking135.蚀刻标记：etched marking136.周期：date code137.翘曲：bow and twist138.外层：outer layer 或者external layer139.内层：inner layer 或者internal layer140.顶层：top layer141.底层：bottom layer142.元件面：component side143.焊接面：solder side144.阻焊层：solder mask layer145.字符层：legend layer (silkscreen layer or over layer) 146.兰胶层：peelable SM layer147.贴片层：paste mask layer148.碳油层：carbon layer149.外形层：outline layer(profile layer)150.白油：white ink151.绿油：green ink152.喷锡：hot air leveling (HAL)153.电金,水金：flash gold154.插头镀金：plated gold edge-board contacts155.金手指：Gold-finger156.防氧化：Entek (OSP)157.沉金：Immersion gold (chem. Gold)158.沉锡：Immersion Tin(chem.Tin)159.沉银：Immersion Silver (chem. silver)160.单面板：single sided board161.双面板：double sided board162.多层板：multilayer board 163.刚性板：rigid board164.挠性板：flexible board165.刚挠板：flex-rigid board166.铣：CNC (mill , routing)167.冲：punching168.倒角：beveling169.斜面：chamfer170.倒圆角：fillet171.尺寸：dimension172.材料：material173.介电常数：Dielectric constant 174.菲林：film175.成像：Imaging176.板镀：Panel Plating177.图镀：Pattern Plating178.后清洗：Final Cleaning179.叠层：stacking structure (stack-up) 180.污染焊盘：contaminate pad181.分孔图：drill chart 或者drill map 182.度数：degree183.被…覆盖：be covered with184.负公差：minus tolerance185.标靶盘：target pad186.外形公差：routing tolerance 187.芯板：core188.半固化片Prepreg189.阻抗线：impedance trace190.评估estimate191.玻纤显露Fiber Exposure192.底铜base copper193.工作搞working Gerber194.原稿original art work195.放宽relax196.挖空blanking 或者cut-out197.一般性阻焊油墨general resist ink198.孔位错误mis hole location199.压合周期press cycle200.毛边serrated edges201.跳印skip printing202.气泡blistering203.隔离焊盘isolated pad204.泪滴tear drops205.箭头arrows206.加大Enlarge207.压合周期press cycle208.毛边serrated edges209.跳印,漏印skip printing210.宽度与厚度的比值width-to-thickness ratio 211.调整adjust212.铜箔基板copper claded laminates213.线路露铜copper exposure214.孔内异物dirty hole215.椭圆形elliptical set216.纤维突出fiber protrusion217.填充料filler218.互相连通interconnection219.改善方案implementation220.板料使用率material use factor221.回路,网络network222.缺口nick223.氧化oxidation224.剥离(剥落) peeling off225.补线不良poor touch-up226.品质等级quality classification227.对位孔registration228.拒收rejectable 229.树脂含量resin content230.排列电阻resistor network231.锣刀（铣刀）routing bit232.孔内沾文字S/L on hole233.孔内绿漆S/M on hole234.线路沾锡solder on trace235.金手指沾锡solder on G/F236.废框scrap237.封孔处理sealing238.间距不足spacing non-enough 239.靶位孔target hole240.测试线路test circuit241.热应力试验thermal stress242.厚度分布thickness distribution 243.薄基板,内层板thin core244.线路缺口及针孔track nick & pin hole 245.裁切线trim line246.真平整true leveling247.真正位置的孔true position248.万用型universal249.气化室vaporizer250.仓库warehouse251.契尖角wedge angle252.线细width reduce253.良率yield254.渗铜,渗入,灯芯效应wicking255.允收acceptable256.试样点coupon location257.经核准的，被认可的approved258.超越胜过,超过其他exceed259.牛皮纸kraft paper260.孔壁破铜Hole void261.孔位破出Hole breakoutPCB生产—经典流程—英文培训教程A. 开料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料发料(Panel)(Shear material to Size)B. 钻孔(Drilling)b-1 内钻(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射钻孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling)C. 干膜制程( Photo Process(D/F))c-1 前处理(Pretreatment)c-2 压膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 显影(Developing)c-5 蚀铜(Etching)c-6 去膜(Stripping)c-7 初检( Touch-up)c-8 化学前处理,化学研磨( Chemical Milling )c-9 选择性浸金压膜(Selective Gold Dry Film Lamination) c-10 显影(Developing )c-11 去膜(Stripping )Developing , Etching & Stripping ( DES )D. 压合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蚀(Microetching)d-3 铆钉组合(eyelet )d-4 叠板(Lay up)d-5 压合(Lamination)d-6 后处理(Post Treatment)d-7 黑氧化( Black Oxide Removal ) d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)E. 减铜(Copper Reduction)e-1 薄化铜(Copper Reduction)F. 电镀(Horizontal Electrolytic Plating)f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)f-3 低于1 mil ( Less than 1 mil Thickness )f-4 高于1 mil ( More than 1 mil Thickness)f-5 砂带研磨(Belt Sanding)f-6 剥锡铅( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 预烤(Precure)g-3 表面刷磨(Scrub)g-4 后烘烤(Postcure)H. 防焊(绿漆/绿油): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 静电喷涂(Spray Coating)h-4 前处理(Pretreatment)h-5 预烤(Precure)h-6 曝光(Exposure)h-7 显影(Develop)h-8 后烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 喷砂( Pumice)(Wet Blasting)h-12 印可剥离防焊(Peelable Solder Mask)I . 镀金Gold platingi-1 金手指镀镍金( Gold Finger )i-2 电镀软金(Soft Ni/Au Plating)i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au)J. 喷锡(Hot Air Solder Leveling)j-1 水平喷锡(Horizontal Hot Air Solder Leveling)j-2 垂直喷锡( Vertical Hot Air Solder Leveling)j-3 超级焊锡(Super Solder )j-4. 印焊锡突点(Solder Bump)K. 成型(Profile)(Form)k-1 捞型(N/C Routing ) (Milling)k-2 模具冲(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜边( Beveling of G/F)L. 开短路测试(Electrical Testing) (Continuity & Insulation Testing) l-1 AOI 光学检查( AOI Inspection)l-2 VRS 目检(Verified & Repaired)l-3 泛用型治具测试(Universal Tester)l-4 专用治具测试(Dedicated Tester)l-5 飞针测试(Flying Probe)M. 终检( Final Visual Inspection)m-1 压板翘( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包装及出货(Packing & shipping)m-4 目检( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 护铜剂(ENTEK Cu-106A)(OSP)m-7 离子残余量测试(Ionic Contamination Test )(Cleanliness Test)m-8 冷热冲击试验(Thermal cycling Testing)m-9 焊锡性试验( Solderability Testing )N. 雷射钻孔(Laser Ablation)N-1 雷射钻Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光对位孔(Laser Ablation Registration Hole)N-3 雷射Mask制作(Laser Mask)N-4 雷射钻孔(Laser Ablation) N-5 AOI 检查及VRS ( AOI Inspection & Verified & Repaired) N-6 Blaser AOI (after Desmear and Microetching)N-7 除胶渣(Desmear)N-8 微蚀(Microetching )。
PCB基材英语
11、 挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film
12、 基体材料：basis material
13、 预浸材料：prepreg
14、 粘结片：bonding sheet
15、 预浸粘结片：preimpregnated bonding sheer
26、 无支撑胶粘剂膜：unsupported adhesive film
27、 覆盖层：cover layer (cover lay)
28、 增强板材：stiffener material
29、 铜箔面：copper-clad surface
30、 去铜箔面：foil removal surface
6、 双面覆铜箔层压板：double-sided copper-clad laminate
7、 复合层压板：composite laminate
8、 薄层压板：thin laminate
9、 金属芯覆铜箔层压板：metal core copper-clad laminate
10、 金属基覆铜层压板：metal base copper-clad laminate
43、 环氧玻璃布玻璃纤维复合覆铜箔板：
epoxide non woven/woven glass reinforced copper-clad laminates
44、 聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates
47、 环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates
PCB专业用语-中英文对照
PCB专业用语一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfacescopper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance。
pcb工厂常用单词
pcb工厂常用单词
在PCB工厂中，一些常用的英文单词包括：
1.circuit board：电路板
2.printed circuit board：印刷电路板
3.PCBA：PCBA，是Printed Circuit Board Assembly的缩写，意思是印
刷电路板组装件
4.trace：迹线，表示电路板上的线路
5.trace width：迹线宽度，表示电路板上线条的粗细
6.trace spacing：迹线间距，表示电路板上两条线路之间的距离
yer：层，表示电路板上的不同导体层
8.dielectric：介质，表示电路板上的绝缘材料
9.via：导通孔，表示电路板上连接不同层导体的孔洞
10.drill hole：钻孔，表示电路板上用于安装元器件的孔洞
ponent：元器件，表示电路板上所安装的电子元件
12.resistor：电阻器
13.capacitor：电容器
14.inductor：电感器
15.transistor：晶体管
16.diode：二极管
17.LED：发光二极管
18.connector：连接器，表示电路板上连接不同部分之间的插座或插
头
19.jumper：跳线，表示用于连接不同部分的短导线
20.tooling hole：工具孔，表示电路板上用于安装治具的孔洞
21.mounting hole：安装孔，表示电路板上用于安装元器件的孔洞
以上仅是部分常用词汇，实际工作中还会涉及到更多专业术语和词汇。
PCB专业术语中英文翻译
PCB专业术语中英文翻译很多PCB的书上使用的是英文，但是大多数的人又看不懂英文，这时候怎么办呢，我们需要翻译，但是如果每看到一个不会的词儿就去翻译，那么就太耗费时间了，所以我们捷多邦总结了一些常用的专业术语的中英文对照，希望能对大家有用。
1.印制电路：printed circuit2.印制线路：printed wiring3.印制板：printed board4.印制板电路：printed circuit board (pcb)5.印制线路板：printed wiring board(pwb)6.印制元件：printed component7.印制接点：printed contact8.印制板装配：printed board assembly9.板：board 110.表面层合电路板：surface laminar circuit (slc)11.埋入凸块连印制板：b2it printed board12.多层膜基板：multi-layered film substrate(mfs)13.层间全内导通多层印制板：alivh multilayer printed board14.载芯片板：chip on board (cob)15.埋电阻板：buried resistance board16.母板：mother board17.单面印制板：single-sided printed board(ssb)18.双面印制板：double-sided printed board(dsb)19.多层印制板：mulitlayer printed board(mlb)20.多层印制电路板：mulitlayer printed circuit board21.多层印制线路板：mulitlayer prited wiring board22.刚性印制板：rigid printed board23.刚性单面印制板：rigid single-sided printed borad24.刚性双面印制板：rigid double-sided printed borad25.刚性多层印制板：rigid multilayer printed board26.子板：daughter board27.背板：backplane28.裸板：bare board29.键盘板夹心板：copper-invar-copper board30.动态挠性板：dynamic flex board31.静态挠性板：static flex board32.可断拼板：break-away planel33.电缆：cable34.挠性扁平电缆：flexible flat cable (ffc)35.薄膜开关：membrane switch36.混合电路：hybrid circuit37.厚膜：thick film38.厚膜电路：thick film circuit39.薄膜：thin film40.挠性多层印制板：flexible multilayer printed board41.挠性印制板：flexible printed board42.挠性单面印制板：flexible single-sided printed board43.挠性双面印制板：flexible double-sided printed board44.挠性印制电路：flexible printed circuit (fpc)45.挠性印制线路：flexible printed wiring46.刚性印制板：flex-rigid printed board, rigid-flex printedboard47.刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed48.刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board49.齐平印制板：flush printed board50.金属芯印制板：metal core printed board51.金属基印制板：metal base printed board52.多重布线印制板：mulit-wiring printed board53.陶瓷印制板：ceramic substrate printed board54.导电胶印制板：electroconductive paste printed board55.模塑电路板：molded circuit board56.模压印制板：stamped printed wiring board57.顺序层压多层印制板：sequentially-laminated mulitlayer58.散线印制板：discrete wiring board59.微线印制板：micro wire board60.积层印制板：buile-up printed board61.积层多层印制板：build-up mulitlayer printed board (bum)62.积层挠印制板：build-up flexible pr上面是一些比较常见的专业用语，有一些不是特别常用的有时候我们也会遇到，所以我们捷多邦也总结了一些不怎么常用的中英文对照，希望对你来说是有用的：1.Absorption 吸收、吸入2.Accelerated Test（Aging）加速试验、加速老化3.Accelerator 加速剂、速化剂4.Accept/Acceptance 允收5.Acceptable Quality Level（AQL）允收品质水准6.Accuracy 准确度ACF：7.Adhesive copper foil 有胶铜箔8.Activator 活化剂、添加剂比称为9.Activator Active parts（Devices）主动零件，指积体电路或电晶体10.Addition Agent 添加剂11.Additive Process 加成法、分全加成、半加成及部份加成12.Back Light（Back Lighting）背光法13.Back-UP 垫板14.Backpanels/ Backplanes 背板、支持板，厚度较厚，15.Ball Grid Array（BGA）球脚车列（封装）16.Barrel 孔壁17.Base Material 基材18.Batch 批（同时间发料某一数量的板子）19.Bevelling 切斜边20.Binder 黏结剂21.Capacitance 电容22.Carbide 碳化物、碳化钨钻头23.CAR: Corrective Action Report 改善报告24.Carbon Treatment 活性碳处理25.Card 卡板26.Carrier 载体27.Cartridge 滤芯28.Cathode 阴极L: Copper Clad Laminates 铜箔基板30.Ceramics 陶瓷31.Certificate 证明书32.CFC 氟氯碳化物33.Chloro-Fluoro-Carbon Chamfer 倒角、去掉直角34.Characteristic Impedance 特性阻抗35.Cheek list 检察清单36.Chip 晶粒、晶片37.Chip On Board 晶片黏著板38.Clean Room 无尘室(Class 100)39.Cleanliness 清洁度40.Clearance 余隙、余环41.COB（Chip on Board）晶片在板上直接组装42.COC（Certificate of Compliance）出货合格书。
中英文对照的PCB专业用语
一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlay er printed board(mlb)13、多层印制电路板：mulitlay er printed circuit board14、多层印制线路板：mulitlay er prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilay er printed board19、挠性多层印制板：flexible multilay er printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilay er printed board, rigid-flex multilay er printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlay er37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlay er printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-lay ered film substrate(mfs)45、层间全内导通多层印制板：alivh multilay er printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：cataly zed board ,coated cataly zed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncataly zed laminate23、粘结层：bonding lay er24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover lay er (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ploy ester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：poly imide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：poly ester resin7、聚酰亚胺树脂：poly imide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acry lic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：sy nthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicy andiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated poly ester36、聚酯薄膜：poly ester37、聚酰亚胺薄膜：poly imide film (pi)38、聚四氟乙烯：polytetrafluoety lene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethy lene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft y arn52、经纱：warp y arn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish ey e68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of y arn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：poly armide fiber79、聚酯纤维非织布：non-woven poly ester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic poly amide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire lay out4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：lay out19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：lay out effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：phy sical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated lay er78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor lay er5、导线宽度/间距：conductor line/space6、第一导线层：conductor lay er no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any lay er inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance。
PCB专业英译术语
PCB专业英译术语PCB（Printed Circuit Board，印刷电路板）是现代电子产品中最常用的一种重要的电路载体，其设计、生产和维修需要大量的技术术语支持。
本文将重点介绍PCB专业英译术语。
一、PCB基础术语1. PCB（Printed Circuit Board）：印刷电路板2. SMT（Surface Mount Technology）：表面贴装技术3. Through-hole Technology：通孔技术4. PTH（Plated Through Hole）：贯穿电解孔5. FR4：一种常用的印刷电路板基材材料，即玻璃纤维材料，通常由环氧树脂和玻璃纤维材料构成6. Pad：焊盘7. Trace：线路8. Via：垂直插孔9. Gerber file：Gerber文件格式，一种电路板设计文件格式10. BOM（Bill of Materials）：物料清单11. NC（Numerical Control）：数控12. DFM（Design for Manufacturability）：可制造性设计二、PCB制造过程相关术语1. CAM（Computer Aided Manufacturing）：计算机辅助制造2. Etch：蚀刻3. Silkscreen：丝网印刷4. Solder mask：焊盘油墨5. Plating：电镀6. HASL（Hot Air Solder Leveling）：热风焊盘处理7. OSP（Organic Solderability Preservatives）：有机可焊保护剂8. Gold Fingers：金手指，指电子产品中可进行插拔操作的特殊金属触点9. DIP（Dual In-line Package）：双列直插封装10. SOP（Small Outline Package）：小封装11. QFN（Quad Flat Package）：四角平封12. BGA（Ball Grid Array）：球网阵列13. PCBA（Printed Circuit Board Assembly）：印刷电路板装配三、PCB测试和维修相关术语1. AOI（Automated Optical Inspection）：自动光学检测2. X-ray Inspection：X光检测3. ICT（In-Circuit Test）：在线测试4. FCT（Functional Circuit Test）：功能测试5. Test point：测试点6. Defect：缺陷7. Repair：修复8. Rework：返工9. Troubleshooting：故障排除四、PCB设计相关术语1. EDA（Electronic Design Automation）：电子设计自动化2. Netlist：网表3. DRC（Design Rule Check）：设计规则检查4. DFM（Design for Manufacturing）：可制造性设计5. Gerber data：Gerber数据6. Simulation：仿真7. Library：元件库8. Footprint：封装9. Copper pour：铜质填充10. Via tenting：垂直插孔塞堵11. Blind vias：盲孔12. Buried vias：穿过孔五、总结本文介绍了PCB专业英译术语中的基础术语、PCB制造过程相关术语、PCB测试和维修相关术语以及PCB设计相关术语。
PCB专业用语 中英文对照
一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board(pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit(fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board,rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board(bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit(slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board(cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable(ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate(ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer(cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core,glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent(wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film(pi)38、聚四氟乙烯：polytetrafluoetylene(ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film(fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise,filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil(ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil(ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil(rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation.(eda)12、工程设计自动化：engineering design automaton.(eda2)13、组装设计自动化：assembly aided architectural design.(aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display.(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format.(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization(design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router(cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing(pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction(track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole(pth)31、余隙孔：access hole32、盲孔：blind via(hole)33、埋孔：buried via hole34、埋/盲孔：buried/blind via35、任意层内部导通孔：any layer inner via hole(alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance整理自快点PCB学院。
线路板PCB专业英语词汇(制造、测试、缺陷名等)
热固性
Clad
覆箔
Layup
叠层
laminating
层压
Postcure
后固化
Curing time
固化时间
Resinflow
树脂流动度
Resin content
树脂含量
PCB英语词汇（二）
3 设计
3.1 通用术语
Computer-aided design (CAD)
计算机辅助设计
导线宽度/ቤተ መጻሕፍቲ ባይዱ距
Conductor layer
导线层
Component hole
元件孔
Mountinghole
安装孔
Supported hole
支撑孔
Unsupported hole
非支撑孔
Via
导通孔
Plated through hole
镀通孔
Blind via (hole)
盲孔
Buried via (hole)
消泡剂
resolution
分辨率
definition
逼真度
ghost image
重影
halation
晕环
air inclusion
夹杂气泡
tackiness
粘着性
post cure
后固化
shelf life
保存期
pot life/ working life
适用期
dip coating
浸涂法
roller coating
网版印刷
Silk screen
丝印网版
Stencil
网版
Screenability
中英文对照的PCB专业用语
中英文对照地PCB专业用语作者：深圳村村长分类:英汉词汇大全提交日期：2007-4-220:41:00 | 访问量：366一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb>5、印制线路板：printed wiring board(pwb>6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb>11、双面印制板：double-sided printed board(dsb>12、多层印制板：mulitlayer printed board(mlb>13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc>24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printedboard26、刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printedboard34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum>41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc>43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs>45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob>47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc>58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl>5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay>28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose papercopper-cladlaminates(phenolic/paper ccl>40、环氧纸质覆铜箔板：epoxide cellulose paper copper-cladlaminates (epoxy/paper ccl>41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-cladlaminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glasscloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glassreinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-cladlaminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-cladlaminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxidewoven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabriccopper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-cladlaminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材地材料1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe>27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi>38、聚四氟乙烯：polytetrafluoetylene (ptfe>39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylenecopolymer film (fep>40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil>90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil>93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc>96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔<剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad>7、计算机辅助制造：computer-aided manufacturing.(cam>8、计算机集成制造：computer integrat manufacturing.(cim>9、计算机辅助工程：computer-aided engineering.(cae>10、计算机辅助测试：computer-aided test.(cat>11、电子设计自动化：electric design automation .(eda>12、工程设计自动化：engineering designautomaton .(eda2>13、组装设计自动化：assembly aided architectural design. (aaad>14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlleddisplay .(ccd>16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf>27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化<设计）：optimization (design>31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走<布）线器：router (cad>54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp>59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线<通道）：conduction (track>2、导线<体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹<背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth>31、余隙孔：access hole32、盲孔：blind via (hole>33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh>36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance b5E2RGbCAP。
PCB专业术语翻译(英语)
PCB专业术语（英语）PCB printed circuit board 印刷电路板，指空的线路板PCBA printed circuit board assembly 印刷电路板组件，指完成元件焊接的线路板组件PW A Printed Wire Assembly，Aperture list Editor：光圈表编辑器。
Aperture list windows：光圈表窗口。
Annular ring：焊环。
Array：拼版或陈列。
Acid trip：蚀刻死角。
Assemby：安装。
Bare Bxnel：光板，未进行插件工序的PCB板。
Bad Badsize：工作台，工作台有效尺寸。
Blind Buried via：盲孔，埋孔。
Chamfer：倒角。
Circuit：线路。
Circuit layer：线路层。
Clamshell tester：双面测试机。
Coordinates Area：坐标区域。
Copy-protect key：软件狗。
Coutour：轮廓。
Draw：一种圆形的光圈，但只是用于创建线路，不用于创建焊盘。
Drill Rack：铅头表。
Drill Rack Editor：铅头表编辑器。
Drill Rack window：铅头表窗口。
D Code：Gerber格式中用不着于表达光圈的代码。
Double-sided Biard：双面板。
End of Block character（EOB）：块结束符。
Extract Netlist：提取网络。
Firdacial：对位标记。
Flash：焊盘，来源于早期矢量光绘机，在矢量光绘机中，焊盘是光通过光圈“闪出”（Flash）而形成的。
Gerber Data：从PCB CAD系统到PCB生产过程中最常用的数据格式。
Grid ：栅格。
Graphical Editor：图形编辑器。
Incremental Data：增量数据。
Land：接地层。
Layer list window：层列表窗口。
PCB工程部专业英语词汇(参考模板)
PCB 工程部专业英文词汇词汇1.板料: material2.最低限度: minimum 或者min.3.最大限度: maximum 或者max.4.基准点(零点) datum point5.周期Date code6.V-cut余厚V-cut remain thickness7.抢电铜皮（假铜）dummy copper8.实物板actual board9.外形及尺寸错误dimension error10.异常情形error data file11.焊锡面与零件面对位偏差misregistration12.孔塞plug hole13.要求requirement14.缺少miss15.偏公差uneven tolerance16.补偿compensation17.表面处理surface treatment18.无铅喷锡Lead free HAL19.金手指斜边bevel of G/F20.制程能力process capability21.建议,暗示suggest22.确保ensure23.满足,达到meet24.为了in order to25.交货期delivery date26.绿油桥solder mask bridge 或者solder mask dam27.根据according to 28.单边3mil per side 3 mil29.直径diameter30.半径radius31.小于3mil less than 3mil32.高于3mil more than 3 mil33.压合结构stacking structure 或者stack_up34.附件：attached file35.样品：sample36.文档：Document37.答复：answer; reply38.规格：spec39.与...同样的：the same as40.前版本：previous version(old version)41.生产：production42.确认：confirm43.再次确认：confirm again44.工程问题：engineering query（EQ）45.尽快：as soon as possible46.生产文件：production Gerber47.联系某人：contact somebody48.提交样板：submit sample49.交货期：delivery date50.电测成本：ET（electrical test）cost51.通断测试：Open and short testing52.参考：refer to53.IPC标准：IPC standard54.IPC二级：IPC class 255.可接受的：acceptable56.允许：permit57.制造：manufacture 或者fabricate58.修改：revision59.公差：tolerance60.忽略：ignore61.工具孔：tooling hole62.安装孔：mounting hole63.元件孔：component hole64.槽孔：slot hole65.邮票孔：snap off hole 或者stamp hole66.导通孔：via hole67.盲孔：blind via hole68.埋孔：buried via hole69.金属化孔：PTH(plated through hole)70.非金属化孔：NPTH( no plated through hole)71.孔位：hole location72.避免：avoid73.原设计：original design74.修改：modify75.按原设计：follow up original design76.附边：waste tab, waste area 或者breakaway tab77.铜条：copper strip78.拼板：panel drawing79.板厚：board thickness80.删除：remove(delete)81.削铜：shave the copper82.露铜：copper exposure 或者exposed copper83.光标点: fiducial mark84.不同：be different from(differ from)85.内弧：inside radius86.焊环：annular ring87.单板尺寸：single size 88.拼板尺寸：panel size89.铣,锣：routing90.铣刀：router 或者Routing bit91.楔形掏槽V-cut 或者V scoring92.哑光：matt93.光亮的：glossy94.锡珠：solder ball(solder plugs)95.阻焊：solder mask(solder resist)96.阻焊开窗：solder mask opening97.单面开窗：single side mask opening98.补油：touch up solder mask99.补线：track welds100.毛刺：burrs101.去毛刺：deburr102.镀层厚度：plating thickness103.清洁度：cleanliness104.离子污染：ionic contamination105.阻燃性等级：flammability retardant rating 106.黑化：black oxidation107.棕化：brown oxidation108.红化：red oxidation109.可焊性不良：poor solderability110.焊料：solder111.包装：packaging112.角标：corner mark113.特性阻抗：characteristic impedance 114.正像：positive115.负片：negative116.镜像：mirror117.线宽：line width 或者trace width118.线距：line spacing 或者trace spacing119.做样：build sample120.按照：according to121.成品：finished122.做变更：make the change123.相类似：similar to124.规格：specification125.下移：shift down126.垂直地：vertically127.水平的：horizontally128.增大：increase129.缩小：decrease130.表面处理：Surface Finishing131.波峰焊：wave solder132.钻孔数据：drilling data133.标记：Logo134.Ul 标记：UL logo,或者Ul Marking135.蚀刻标记：etched marking136.周期：date code137.翘曲：bow and twist138.外层：outer layer 或者external layer139.内层：inner layer 或者internal layer140.顶层：top layer141.底层：bottom layer142.元件面：component side143.焊接面：solder side144.阻焊层：solder mask layer145.字符层：legend layer (silkscreen layer or over layer) 146.兰胶层：peelable SM layer147.贴片层：paste mask layer 148.碳油层：carbon layer149.外形层：outline layer(profile layer)150.白油：white ink151.绿油：green ink152.喷锡：hot air leveling (HAL)153.电金,水金：flash gold154.插头镀金：plated gold edge-board contacts 155.金手指：Gold-finger156.防氧化：Entek (OSP)157.沉金：Immersion gold (chem. Gold)158.沉锡：Immersion Tin(chem.Tin)159.沉银：Immersion Silver (chem. silver) 160.单面板：single sided board161.双面板：double sided board162.多层板：multilayer board163.刚性板：rigid board164.挠性板：flexible board165.刚挠板：flex-rigid board166.铣：CNC (mill , routing)167.冲：punching168.倒角：beveling169.斜面：chamfer170.倒圆角：fillet171.尺寸：dimension172.材料：material173.介电常数：Dielectric constant174.菲林：film175.成像：Imaging176.板镀：Panel Plating177.图镀：Pattern Plating178.后清洗：Final Cleaning179.叠层：stacking structure (stack-up) 180.污染焊盘：contaminate pad181.分孔图：drill chart 或者drill map 182.度数：degree183.被…覆盖：be covered with184.负公差：minus tolerance185.标靶盘：target pad186.外形公差：routing tolerance 187.芯板：core188.半固化片Prepreg189.阻抗线：impedance trace190.评估estimate191.玻纤显露Fiber Exposure192.底铜base copper193.工作搞working Gerber194.原稿original art work195.放宽relax196.挖空blanking 或者cut-out 197.一般性阻焊油墨general resist ink 198.孔位错误mis hole location 199.压合周期press cycle200.毛边serrated edges201.跳印skip printing202.气泡blistering203.隔离焊盘isolated pad204.泪滴tear drops205.箭头arrows206.加大Enlarge207.压合周期press cycle 208.毛边serrated edges209.跳印,漏印skip printing210.宽度与厚度的比值width-to-thickness ratio 211.调整adjust212.铜箔基板copper claded laminates213.线路露铜copper exposure214.孔内异物dirty hole215.椭圆形elliptical set216.纤维突出fiber protrusion217.填充料filler218.互相连通interconnection219.改善方案implementation220.板料使用率material use factor221.回路,网络network222.缺口nick223.氧化oxidation224.剥离(剥落) peeling off225.补线不良poor touch-up226.品质等级quality classification227.对位孔registration228.拒收rejectable229.树脂含量resin content230.排列电阻resistor network231.锣刀（铣刀）routing bit232.孔内沾文字S/L on hole233.孔内绿漆S/M on hole234.线路沾锡solder on trace235.金手指沾锡solder on G/F236.废框scrap237.封孔处理sealing238.间距不足spacing non-enough239.靶位孔target hole240.测试线路test circuit241.热应力试验thermal stress242.厚度分布thickness distribution243.薄基板,内层板thin core244.线路缺口及针孔track nick & pin hole245.裁切线trim line246.真平整true leveling247.真正位置的孔true position248.万用型universal249.气化室vaporizer250.仓库warehouse251.契尖角wedge angle252.线细width reduce253.良率yield254.渗铜,渗入,灯芯效应wicking255.允收acceptable256.试样点coupon location257.经核准的，被认可的approved258.超越胜过,超过其他exceed259.牛皮纸kraft paper260.孔壁破铜Hole void261.孔位破出Hole breakoutPCB生产—经典流程—英文培训教程A. 开料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料发料(Panel)(Shear material to Size) B. 钻孔(Drilling)b-1 内钻(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射钻孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling)C. 干膜制程( Photo Process(D/F))c-1 前处理(Pretreatment)c-2 压膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 显影(Developing)c-5 蚀铜(Etching)c-6 去膜(Stripping)c-7 初检( Touch-up)c-8 化学前处理,化学研磨( Chemical Milling )c-9 选择性浸金压膜(Selective Gold Dry Film Lamination) c-10 显影(Developing )c-11 去膜(Stripping )Developing , Etching & Stripping ( DES )D. 压合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蚀(Microetching)d-3 铆钉组合(eyelet )d-4 叠板(Lay up)d-5 压合(Lamination)d-6 后处理(Post Treatment)d-7 黑氧化( Black Oxide Removal )d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)E. 减铜(Copper Reduction)e-1 薄化铜(Copper Reduction)F. 电镀(Horizontal Electrolytic Plating)f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)f-3 低于1 mil ( Less than 1 mil Thickness )f-4 高于1 mil ( More than 1 mil Thickness)f-5 砂带研磨(Belt Sanding)f-6 剥锡铅( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 预烤(Precure)g-3 表面刷磨(Scrub)g-4 后烘烤(Postcure)H. 防焊(绿漆/绿油): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 静电喷涂(Spray Coating)h-4 前处理(Pretreatment)h-5 预烤(Precure)h-6 曝光(Exposure)h-7 显影(Develop)h-8 后烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 喷砂( Pumice)(Wet Blasting)h-12 印可剥离防焊(Peelable Solder Mask)I . 镀金Gold platingi-1 金手指镀镍金( Gold Finger )i-2 电镀软金(Soft Ni/Au Plating)i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au)J. 喷锡(Hot Air Solder Leveling)j-1 水平喷锡(Horizontal Hot Air Solder Leveling)j-2 垂直喷锡( Vertical Hot Air Solder Leveling)j-3 超级焊锡(Super Solder )j-4. 印焊锡突点(Solder Bump)K. 成型(Profile)(Form)k-1 捞型(N/C Routing ) (Milling)k-2 模具冲(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜边( Beveling of G/F)L. 开短路测试(Electrical Testing) (Continuity & Insulation Testing) l-1 AOI 光学检查( AOI Inspection)l-2 VRS 目检(Verified & Repaired)l-3 泛用型治具测试(Universal Tester)l-4 专用治具测试(Dedicated Tester)l-5 飞针测试(Flying Probe)M. 终检( Final Visual Inspection)m-1 压板翘( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包装及出货(Packing & shipping)m-4 目检( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 护铜剂(ENTEK Cu-106A)(OSP)m-7 离子残余量测试(Ionic Contamination Test )(Cleanliness Test)m-8 冷热冲击试验(Thermal cycling Testing)m-9 焊锡性试验( Solderability Testing )N. 雷射钻孔(Laser Ablation)N-1 雷射钻Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光对位孔(Laser Ablation Registration Hole)N-3 雷射Mask制作(Laser Mask)N-4 雷射钻孔(Laser Ablation) N-5 AOI 检查及VRS ( AOI Inspection & Verified & Repaired)N-6 Blaser AOI (after Desmear and Microetching) N-7 除胶渣(Desmear)N-8 微蚀(Microetching )---精心整理，希望对您有所帮助。
PCB专业英语和层定义
PCB专业英语(PCB SPECIAL ENGLISH)1.PCB=Printed Circuit Board 电路板2.CAM=Computer aided manufacture 计算机辅助3.Pad 焊盘4.Annular ring 焊环5.AOI=automatic optical inspection 自动光学检测6.Charge of free 免费7.WIP=work in process 在线板8.DCC=document control center 文控中心9.Legend 字符10.CS=Component Side =Top Side （顶层）元件面11.SS=Solder Side =Bottom Side （底层）焊锡面12.Gold Plated 电金，镀金13.Nickel Plated 电镍，镀镍14.Immersion Gold 沉金=沉镍金15.Carbon Ink Print 印碳油16.Microsection Report 切片报告，横切面报告17.X-out=Cross-out 打“X”报告18.Panel （客户称）拼板，（生产线称）工作板19.Marking 标记，UL 标记20.Date code 生产周期21.Unit 单元，单位22.Profile 外形，轮廓<outline>23.Profile By Routing 锣(铣)外形24.Wet Film 湿菲林,湿绿油,湿膜25.Slot 槽,方坑26.Base Material=Base Laminate 基材,板料27.V-out =V-score V形槽28.Finished 成品29.Marketing 市场部30.Gerber File GERBER文件31.UL LOGO UL标记32.E-Test=Electric Open/Short Test 电子测试33.PO=Purchase Order 订单34.Tolerance 公差35.Rigid,Flexible Board 刚性,软性板36.Board cut 开料37.Board baking 焗板38.Drill 钻孔39.PTH=Plated Through Hole 镀通孔,沉铜40.Panel plating 板面电镀,全板电镀41.Photo Image 图象,线路图形42.Pattern plating 线路电镀43.Etching 蚀板,蚀刻44.SM=Solder Mask 防焊,阻焊,绿油45.SR=Solder Resist 防焊,阻焊,绿油46.Gold finger 金手指47.Silkscreen 丝印字符48.HAL=HASL=Hot air(Solder)leveling 热风整平喷锡49.Routing 锣板,铣板50.Punching 冲板,啤板51.FOC=final quality checking 终检,最后检查52.FOA=final quality audit 最后稽查(抽查)53.Shippment 出货54.Flux 松香55.Au金,Cu铜,Ni镍,Pb铅,Tn锡,Tin-lead锡铅合金56.Lead free 无铅57.COC=compliance of certificate 材料证明书58.Microsection=cross section 微切片,横切片59.Chamical gold 沉镍金60.Mould=punch die 模具,啤模61.MI=manufacture instruction 制作批示62.QA=quality assurance 品质保证63.CAD=computer aided design 计算机辅助设计64.Drill bit size钻咀直径<diameter>65.Bow and twist 板弯和板曲66.Hit 击打,孔数67.Bonding 邦定,点焊68.Test coupon 测试模块(科邦)69.Thieving copper 抢电流铜皮70.Rail-web71.Break-up tab 工艺边72.Break away tab 工艺边73.GND=ground 地线,大铜皮74.Hole edge 孔边,孔内75.Stamp hole 邮票孔76.Template 天坯,型板,钻孔样板(首板)77.Dry film 干菲林,干膜78.LPI=liquid photo image 液态感光=湿绿油79.Multilayer 多层板80.SMD=surface mouted device 贴片,表面贴装器件81.SMT=surface mouted technology 表面贴装技术82.Peelable mask=blue gel 蓝胶83.Tooling hole 工艺孔,管位,定位孔,工具孔84.Fiducial mask 测光点,光学对位点,对光点,电眼85.Copper foil 铜箔86.Dimension 尺寸87.Nagative负的,positive正的88.Flash gold 闪镀金,镀薄金89.Engineering department 工程部90.Delivery date 交货期91.Bevelling 斜边92.Spacing=gap 间隙,气隙,线隙PCB的各层定义及描述为了方便与印制板厂家的技术沟通，提高对PCB的技术认知一致度，特在此将我司常用PCB的有关板层特性做简单说明，请爱好者参考此说明进行设计和制造。
PCB常用英语汇总
PCB及PCBA常用英语汇总(4)1 内层开路 Inner open2 内层断路 Inner short3 外层开路 Outer open4 外层断路 Outer short5 内层蚀刻过度 Inner over ecthing6 外层蚀刻过度 Outer over ecthing7 内层树脂气泡 Resin void8 内层杂物 Foreign material9 内层图形移位 Inner pattern mis-registration10 层与层移位 Layer to layer mis-registration11 打孔不良 Improper targeting12 内层蚀刻不净 Inner under etching13 露布纹 Weave texture/exposure14 檫花（氧化膜面） Scratch(Oxide surface)15 板损坏 Damaged board16 分层（物料） Delamination (Raw material)17 内层不配套 Excessive inner core18 板过厚 Over thickness19 白点（压板） Measling (Pressing)20 白点（喷锡） Measling (HSAL)21 板曲 Warpage22 板焦黄 Burnt23 起皱 Wrinkle24 起泡（压板） Blistering (Pressing)25 镀层起泡 Blistering (Cu plating)26 喷锡起泡 Blistering (HSAL)27 板面凹痕 DENT (Pressing profilling G/F)28 白斑 Crazing29 胶渣 Gum residue30 孔未穿 Incomplete drilling31 披锋 Burr32 多孔 Extra hole33 偏孔 Hole shift34 孔径大 Hole oversize35 孔径小 Hole undersize36 少孔 Missing Hole37 塞孔 Block hole38 崩孔 Hole breakout39 孔粗糙(镀铜） Hole roughness（Cu plating)40 孔粗糙（机械钻孔） Hole roughness(mechanicaldrill)41 崩线、线路缺口 Nick / void on trace42 缺口 Nick / void on pad43 曝光过度 Over-exposure44 曝光不良 Under exposure45 显影不足 Under develop46 干膜脱落 D/F Peel off47 干膜碎 D/F Rdsidue48 干膜移位 D/F Mis-registration49 标志不清（曝光） Illegible marking (exposure)50 错菲林 Wrong A/W51 非镀铜孔有铜 Copper in NPTH52 镀铜孔内无铜 No copper in PTH53 渗镀 Nickel smear54 电镀粗糙 Rough plating。
pcb英文术语
pcb英文术语
以下是一些PCB（Printed Circuit Board，印刷电路板）的英文术语：
1. PCB：Printed Circuit Board，印刷电路板
2. SMD：Surface Mount Device，表面贴装器件
3. BGA：Ball Grid Array，球栅阵列
4. FPGA：Field Programmable Gate Array，现场可编程门阵列
5. DIP：Dual In-line Package，双列直插封装
6. PTH：Plated Through Hole，贯穿孔
7. VIA：Vertical Interconnect Access，垂直互连通孔
8. NC：No Connection，未连接
9. Pads：焊盘
10. Gerber File：Gerber文件，包含PCB设计图层信息的文件格式
11. Silk Screen：丝网印刷，用于标记元件位置或文字的印刷层
12. Copper Trace：铜线追踪，指PCB上的导线路径
13. Solder Mask：焊盘阻焊层，用于保护焊盘和其他不需要焊接的区域
14. Component Footprint：元件封装，描述组件在PCB上的安装尺寸和引脚布局
15. ESD：Electrostatic Discharge，静电放电
希望这些术语能对您有所帮助！如果您有其他问题，请随时提问。
PCB基本英语.
流程Board cut 开料Carbon printing 碳油印刷Inner dry film 内层干膜Peelable blue mask 蓝胶Inner etching 内层蚀刻ENIG(Electroless nickel immersion gold) 沉镍金Inner dry film stripping 内层干膜退膜HAL(hot air leveling) 喷锡AOI（Automatic Optical Inspection）自动光学检测OSP（Organic solderability preservative）有机保焊Pressing 压板Punching 啤板Drilling 钻孔Profiling 外形加工Desmear 除胶渣，去钻污 E-Test 电性测试PTH 镀通孔，沉铜FQC(final quality control) 最终品质控制Panel plating 整板电镀FQA(Final quality audit) 最终品质保证Outer dry film 外层干膜Packing 包装Etching 蚀刻IPQA(In-process quality audit) 流程QA Tin stripping 退锡IPQC(In-process quality control) 流程QC EQC（QC after etching）蚀检QCIQC(Incoming quality control) 来料检查Solder mask 感阻MRB(material review board) 材料评审委员会Component mark 字符QA(Quality assurance) 品质保证Physical Laboratory 物理实验室QC(Quality control) 品质控制Chemistry Laboratory 化学实验室Document control center 文件控制中心2nd Drilling 二钻Routing 锣板，铣板Brown oxidation 棕化Waste water treatment 污水处理V-cut V坑WIP（work in process）半成品Store/stock 仓库 F.G(Finished goods) 成品概述Printed Circuit Board 印制电路板Flexible Printed Circuit, FPC 软板Double-Side Printed Board 双面板IPC（The Institute for Interconnecting and Packing Electronic Circuits）电子电路互连与封装协会CPAR（Corrective & Preventive Action Request）要求纠正预防措施Flammability Rate燃性等级Characteristic impedance 特性阻抗BUM（Build-up multilayer）积层多层板Date Code周期代码CCL（Copper-clad laminate）覆铜板Ionic contamination 离子性污染Acceptance Quality Level (AQL)允收水平HDI（High density interconnecting）高密度互连板Base Material基材Radius 半径Capacity 生产能力Diameter 直径Capability 工艺能力PPM(Parts Per Million) 百万分之几CAM（computer-aided manufacturing) 计算机辅助制造Underwriters Laboratories Inc. 美国保险商实验所CAD (computer-aided design) 计算机辅助设计Statistical Process Control 统计过程控制Specification 规格，规范Via 导通孔Dimension 尺寸Buried /blind via 埋/盲孔Tolerance 公差Tooling hole 定位孔Oven 焗炉Output/throughput 产量湿流程PTH（plated through hole）镀通孔（俗称沉铜）Acid cleaning 酸性除油PP(Panel Plating) 板电Acid dip 酸洗Pattern plating 图电Pre-dip 预浸Line width 线宽Alkaline cleaning 碱性除油Spacing 线隙Flux 松香Deburring 去毛刺（沉铜前磨板）Hot air leveling 喷锡Carbon treatment 碳处理Skip plating 跳镀，漏镀Track/conductor 导线Undercut 侧蚀Aspect ratio深径比Water rinsing水洗Etch Factor 蚀刻因子Transportation 行车Back Light Test背光测试Rack挂架Pink ring粉红圈Maintenance 保养干流程Hole location孔位Annular ring 孔环Image Transfer图象转移Component Side(C/S) 元件面Artwork 底片Solder Side(S/S) 焊接面Mylar 胶片Matte Solder Mask 哑绿油Silkscreen/legend/Component Mark文字Hole breakout 破孔Fiducial mark 基点，对光点Scrubbing 磨板Expose 曝光Developing 显影内层制作Core material 内层芯板Thermal pad 散热PAD Pre-preg PP片Resin content 树脂含量Kraft Paper牛皮纸Brown oxidation 棕化Lay up 排版Black Oxidation 黑化Registration 对位Base material 板材Delamination 分层其它Wicking灯芯效应Hole size 孔径(尺寸) Yield良品率Touch Up修理Warp and Twist 板曲度Solvent Test 溶剂测试Peel off 剥离Company Logo 公司标识Tape Test 胶纸试验UL Mark UL 标记Cosmetic 外观Function 功能Tin/Lead Ratio 锡/铅比例Reliability Tests 可靠性试验Hole Wall Roughness 孔壁粗糙度Base Copper Thickness 底铜厚度PCB专业英语(PCB SPECIAL ENGLISH)1.PCB=Printed Circuit Board 电路板2.CAM=Computer aided manufacture 计算机辅助3.Pad 焊盘4.Annular ring 焊环5.AOI=automatic optical inspection 自动光学检测6.Charge of free 免费7.WIP=work in process 在线板8.DCC=document control center 文控中心9.Legend 字符10.CS=Component Side =Top Side （顶层）元件面11.SS=Solder Side =Bottom Side （底层）焊锡面12.Gold Plated 电金，镀金13.Nickel Plated 电镍，镀镍14.Immersion Gold 沉金=沉镍金15.Carbon Ink Print 印碳油16.Microsection Report 切片报告，横切面报告17.X-out=Cross-out 打"X"报告18.Panel （客户称）拼板，（生产线称）工作板19.Marking 标记，UL 标记20.Date code 生产周期21.Unit 单元，单位22.Profile 外形，轮廓<outline>23.Profile By Routing 锣(铣)外形24.Wet Film 湿菲林,湿绿油,湿膜25.Slot 槽,方坑26.Base Material=Base Laminate 基材,板料27.V-out =V-score V形槽28.Finished 成品29.Marketing 市场部30.Gerber File GERBER文件31.UL LOGO UL标记32.E-Test=Electric Open/Short Test 电子测试33.PO=Purchase Order 订单34.Tolerance 公差35.Rigid,Flexible Board 刚性,软性板36.Board cut 开料37.Board baking 焗板38.Drill 钻孔39.PTH=Plated Through Hole 镀通孔,沉铜40.Panel plating 板面电镀,全板电镀41.Photo Image 图象,线路图形42.Pattern plating 线路电镀43.Etching 蚀板,蚀刻44.SM=Solder Mask 防焊,阻焊,绿油45.SR=Solder Resist 防焊,阻焊,绿油46.Gold finger 金手指47.Silkscreen 丝印字符48.HAL=HASL=Hot air(Solder)leveling 热风整平喷锡49.Routing 锣板,铣板50.Punching 冲板,啤板51.FOC=final quality checking 终检,最后检查52.FOA=final quality audit 最后稽查(抽查)53.Shippment 出货54.Flux 松香55.Au金,Cu铜,Ni镍,Pb铅,Tn锡,Tin-lead锡铅合金56.Lead free 无铅57.COC=compliance of certificate 材料证明书58.Microsection=cross section 微切片,横切片59.Chamical gold 沉镍金60.Mould=punch die 模具,啤模61.MI=manufacture instruction 制作批示62.QA=quality assurance 品质保证63.CAD=computer aided design 计算机辅助设计64.Drill bit size钻咀直径<diameter>65.Bow and twist 板弯和板曲66.Hit 击打,孔数67.Bonding 邦定,点焊68.Test coupon 测试模块(科邦)69.Thieving copper 抢电流铜皮70.Rail-web71.Break-up tab 工艺边72.Break away tab 工艺边73.GND=ground 地线,大铜皮74.Hole edge 孔边,孔内75.Stamp hole 邮票孔76.Template 天坯,型板,钻孔样板(首板)77.Dry film 干菲林,干膜78.LPI=liquid photo image 液态感光=湿绿油79.Multilayer 多层板80.SMD=surface mouted device 贴片,表面贴装器件81.SMT=surface mouted technology 表面贴装技术82.Peelable mask=blue gel 蓝胶83.Tooling hole 工艺孔,管位,定位孔,工具孔84.Fiducial mask 测光点,光学对位点,对光点,电眼85.Copper foil 铜箔86.Dimension 尺寸87.Nagative负的,positive正的88.Flash gold 闪镀金,镀薄金89.Engineering department 工程部90.Delivery date 交货期91.Bevelling 斜边92.Spacing=gap 间隙,气隙,线隙PCB的各层定义及描述为了方便与印制板厂家的技术沟通，提高对PCB的技术认知一致度，特在此将我司常用PCB的有关板层特性做简单说明，请爱好者参考此说明进行设计和制造。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
流程Board cut 开料Carbon printing 碳油印刷Inner dry film 内层干膜Peelable blue mask 蓝胶Inner etching 内层蚀刻ENIG(Electroless nickel immersion gold) 沉镍金Inner dry film stripping 内层干膜退膜HAL(hot air leveling) 喷锡AOI（Automatic Optical Inspection）自动光学检测OSP（Organic solderability preservative）有机保焊Pressing 压板Punching 啤板Drilling 钻孔Profiling 外形加工Desmear 除胶渣，去钻污 E-Test 电性测试PTH 镀通孔，沉铜FQC(final quality control) 最终品质控制Panel plating 整板电镀FQA(Final quality audit) 最终品质保证Outer dry film 外层干膜Packing 包装Etching 蚀刻IPQA(In-process quality audit) 流程QA Tin stripping 退锡IPQC(In-process quality control) 流程QC EQC（QC after etching）蚀检QCIQC(Incoming quality control) 来料检查Solder mask 感阻MRB(material review board) 材料评审委员会Component mark 字符QA(Quality assurance) 品质保证Physical Laboratory 物理实验室QC(Quality control) 品质控制Chemistry Laboratory 化学实验室Document control center 文件控制中心2nd Drilling 二钻Routing 锣板，铣板Brown oxidation 棕化Waste water treatment 污水处理V-cut V坑WIP（work in process）半成品Store/stock 仓库 F.G(Finished goods) 成品概述Printed Circuit Board 印制电路板Flexible Printed Circuit,FPC 软板Double-Side Printed Board双面板IPC（The Institute for Interconnecting and Packing Electronic Circuits）电子电路互连与封装协会CPAR（Corrective & Preventive Action Request）要求纠正预防措施Flammability Rate燃性等级Characteristic impedance 特性阻抗BUM（Build-up multilayer）积层多层板Date Code周期代码CCL（Copper-clad laminate）覆铜板Ionic contamination 离子性污染Acceptance Quality Level (AQL)允收水平HDI（High density interconnecting）高密度互连板Base Material基材Radius 半径Capacity 生产能力Diameter 直径Capability 工艺能力PPM(Parts Per Million) 百万分之几CAM（computer-aided manufacturing)计算机辅助制造Underwriters Laboratories Inc. 美国保险商实验所CAD (computer-aided design)计算机辅助设计Statistical Process Control 统计过程控制Specification 规格，规范Via导通孔Dimension 尺寸Buried /blind via埋/盲孔Tolerance 公差Tooling hole定位孔Oven 焗炉Output/throughput 产量湿流程PTH（plated through hole）镀通孔（俗称沉铜）Acid cleaning 酸性除油PP(Panel Plating) 板电Acid dip 酸洗Pattern plating 图电Pre-dip 预浸Line width 线宽Alkaline cleaning 碱性除油Spacing 线隙Flux 松香Deburring 去毛刺（沉铜前磨板）Hot air leveling 喷锡Carbon treatment 碳处理Skip plating 跳镀，漏镀Track/conductor 导线Undercut 侧蚀Aspect ratio深径比Water rinsing水洗Etch Factor 蚀刻因子Transportation 行车Back Light Test背光测试Rack挂架Pink ring粉红圈Maintenance 保养干流程Hole location孔位Annular ring 孔环Image Transfer图象转移Component Side(C/S) 元件面Artwork 底片Solder Side(S/S) 焊接面Mylar 胶片Matte Solder Mask 哑绿油Silkscreen/legend/Component Mark文字Hole breakout 破孔Fiducial mark 基点，对光点Scrubbing 磨板Expose 曝光Developing 显影内层制作Core material内层芯板Thermal pad 散热PADPre-preg PP片Resin content 树脂含量Kraft Paper牛皮纸Brown oxidation 棕化Lay up 排版Black Oxidation 黑化Registration 对位Base material 板材Delamination 分层其它Wicking灯芯效应Hole size 孔径(尺寸)Yield良品率Touch Up修理Warp and Twist 板曲度Solvent Test 溶剂测试Peel off 剥离Company Logo 公司标识Tape Test 胶纸试验UL Mark UL 标记Cosmetic 外观Function 功能Tin/Lead Ratio 锡/铅比例Reliability Tests 可靠性试验Hole Wall Roughness 孔壁粗糙度Base Copper Thickness 底铜厚度PCB专业英语(PCB SPECIAL ENGLISH)1.PCB=Printed Circuit Board 电路板2.CAM=Computer aided manufacture 计算机辅助3.Pad 焊盘4.Annular ring 焊环5.AOI=automatic optical inspection 自动光学检测6.Charge of free 免费7.WIP=work in process 在线板8.DCC=document control center 文控中心9.Legend 字符10.CS=Component Side =Top Side （顶层）元件面11.SS=Solder Side =Bottom Side （底层）焊锡面12.Gold Plated 电金，镀金13.Nickel Plated 电镍，镀镍14.Immersion Gold 沉金=沉镍金15.Carbon Ink Print 印碳油16.Microsection Report 切片报告，横切面报告17.X-out=Cross-out 打"X"报告18.Panel （客户称）拼板，（生产线称）工作板19.Marking 标记，UL 标记20.Date code 生产周期21.Unit 单元，单位22.Profile 外形，轮廓<outline>23.Pro Routing 锣(铣)外形24.Wet Film 湿菲林,湿绿油,湿膜25.Slot 槽,方坑26.Base Material=Base Laminate 基材,板料27.V-out =V-score V形槽28.Finished 成品29.Marketing 市场部30.Gerber File GERBER文件31.UL LOGO UL标记32.E-Test=Electric Open/Short Test 电子测试33.PO=Purchase Order 订单34.Tolerance 公差35.Rigid,Flexible Board 刚性,软性板36.Board cut 开料37.Board baking 焗板38.Drill 钻孔39.PTH=Plated Through Hole 镀通孔,沉铜40.Panel plating 板面电镀,全板电镀41.Photo Image 图象,线路图形42.Pattern plating 线路电镀43.Etching 蚀板,蚀刻44.SM=Solder Mask 防焊,阻焊,绿油45.SR=Solder Resist 防焊,阻焊,绿油46.Gold finger 金手指47.Silkscreen 丝印字符48.HAL=HASL=Hot air(Solder)leveling 热风整平喷锡49.Routing 锣板,铣板50.Punching 冲板,啤板51.FOC=final quality checking 终检,最后检查52.FOA=final quality audit 最后稽查(抽查)53.Shippment 出货54.Flux 松香55.Au金,Cu铜,Ni镍,Pb铅,Tn锡,Tin-lead锡铅合金56.Lead free 无铅57.COC=compliance of certificate 材料证明书58.Microsection=cross section 微切片,横切片59.Chamical gold 沉镍金60.Mould=punch die 模具,啤模61.MI=manufacture instruction 制作批示62.QA=quality assurance 品质保证63.CAD=computer aided design 计算机辅助设计64.Drill bit size钻咀直径<diameter>65.Bow and twist 板弯和板曲66.Hit 击打,孔数67.Bonding 邦定,点焊68.Test coupon 测试模块(科邦)69.Thieving copper 抢电流铜皮70.Rail-web71.Break-up tab 工艺边72.Break away tab 工艺边73.GND=ground 地线,大铜皮74.Hole edge 孔边,孔内75.Stamp hole 邮票孔76.Template 天坯,型板,钻孔样板(首板)77.Dry film 干菲林,干膜78.LPI=liquid photo image 液态感光=湿绿油79.Multilayer 多层板80.SMD=surface mouted device 贴片,表面贴装器件81.SMT=surface mouted technology 表面贴装技术82.Peelable mask=blue gel 蓝胶83.Tooling hole 工艺孔,管位,定位孔,工具孔84.Fiducial mask 测光点,光学对位点,对光点,电眼85.Copper foil 铜箔86.Dimension 尺寸87.Nagative负的,positive正的88.Flash gold 闪镀金,镀薄金89.Engineering department 工程部90.Delivery date 交货期91.Bevelling 斜边92.Spacing=gap 间隙,气隙,线隙PCB的各层定义及描述为了方便与印制板厂家的技术沟通，提高对PCB的技术认知一致度，特在此将我司常用PCB的有关板层特性做简单说明，请爱好者参考此说明进行设计和制造。