焊接英汉翻译
常用焊接中英文词典
焊接代号AW——ARC WELDING——电弧焊AHW——atomic hydrogen welding——原子氢焊BMAW——bare metal arc welding——无保护金属丝电弧焊CAW——carbon arc welding——碳弧焊CAW-G——gas carbon arc welding——气保护碳弧焊CAW-S——shielded carbon arc welding——有保护碳弧焊CAW-T——twin carbon arc welding——双碳极间电弧焊EGW——electrogas welding——气电立焊FCAW——flux cored arc welding——药芯焊丝电弧焊FCW-G——gas-shielded flux cored arc welding——气保护药芯焊丝电弧焊FCW-S——self-shielded flux cored arc welding——自保护药芯焊丝电弧焊GMAW——gas metal arc welding——熔化极气体保护电弧焊GMAW-P——pulsed arc——熔化极气体保护脉冲电弧焊GMAW-S——short circuiting arc——熔化极气体保护短路过度电弧焊GTAW——gas tungsten arc welding——钨极气体保护电弧焊GTAW-P——pulsed arc——钨极气体保护脉冲电弧焊MIAW——magnetically impelled arc welding——磁推力电弧焊PAW——plasma arc welding——等离子弧焊SMAW——shielded metal arc welding——焊条电弧焊SW——stud arc welding——螺栓电弧焊SAW——submerged arc welding——埋弧焊SAW-S——series——横列双丝埋弧焊RW——RWSISTANCE WELDING——电阻焊FW——flash welding——闪光焊RW-PC——pressure controlled resistance welding——压力控制电阻焊PW——projection welding——凸焊RSEW——resistance seam welding——电阻缝焊RSEW-HF——high-frequency seam welding——高频电阻缝焊RSEW-I——induction seam welding——感应电阻缝焊RSEW-MS——mash seam welding——压平缝焊RSW——resistance spot welding——点焊UW——upset welding——电阻对焊UW-HF——high-frequency ——高频电阻对焊UW-I——induction——感应电阻对焊SSW——SOLID STATE WELDING——固态焊CEW——co-extrusion welding——CW——cold welding——冷压焊DFW——diffusion welding——扩散焊HIPW——hot isostatic pressure diffusion welding——热等静压扩散焊EXW——explosion welding——爆炸焊FOW——forge welding——锻焊FRW——friction welding——摩擦焊FRW-DD——direct drive friction welding——径向摩擦焊FSW——friction stir welding——搅拌摩擦焊FRW-I——inertia friction welding——惯性摩擦焊HPW——hot pressure welding——热压焊ROW——roll welding——热轧焊USW——ultrasonic welding——超声波焊S——SOLDERING——软钎焊DS——dip soldering——浸沾钎焊FS——furnace soldering——炉中钎焊IS——induction soldering——感应钎焊IRS——infrared soldering——红外钎焊INS——iron soldering——烙铁钎焊RS——resistance soldering——电阻钎焊TS——torch soldering——火焰钎焊UUS——ultrasonic soldering——超声波钎焊WS——wave soldering——波峰钎焊B——BRAZING——软钎焊BB——block brazing——块钎焊DFB——diffusion brazing——扩散焊DB——dip brazing——浸沾钎焊EXB——exothermic brazing——反应钎焊FB——furnace brazing——炉中钎焊IB——induction brazing——感应钎焊IRB——infrared brazing——红外钎焊RB——resistance brazing——电阻钎焊TB——torch brazing——火焰钎焊TCAB——twin carbon arc brazing——双碳弧钎焊OFW——OXYFUEL GAS WELDING——气焊AAW——air-acetylene welding——空气乙炔焊OAW——oxy-acetylene welding——氧乙炔焊OHW——oxy-hydrogen welding——氢氧焊PGW——pressure gas welding——气压焊OTHER WELDING AND JOINING——其他焊接与连接方法AB——adhesive bonding——粘接BW——braze welding——钎接焊ABW——arc braze welding——电弧钎焊CABW——carbon arc braze welding——碳弧钎焊EBBW——electron beam braze welding——电子束钎焊EXBW——exothermic braze welding——热反应钎焊FLB——flow brazing——波峰钎焊FLOW——flow welding——波峰焊LBBW——laser beam braze welding——激光钎焊EBW——electron beam welding——电子束焊EBW-HV——high vacuum——高真空电子束焊EBW-MV——medium vacuum——中真空电子束焊EBW-NV——non vacuum——非真空电子束焊ESW——electroslag welding——电渣焊ESW-CG——consumable guide eletroslag welding——熔嘴电渣焊IW——induction welding——感应焊LBW——laser beam welding——激光焊PEW——percussion welding——冲击电阻焊TW——thermit welding——热剂焊THSP——THERMAL SPRAYING——热喷涂ASP——arc spraying——电弧喷涂FLSP——flame spraying——火焰喷涂FLSP-W——wire flame spraying——丝材火焰喷涂HVOF——high velocity oxyfuel spraying——高速氧燃气喷涂PSP——plasma spraying——等离子喷涂VPSP-W——vacuum plasma spraying——真空等离子喷涂TC——THERMAL CUTTING——热切割OC——OXYGEN CUTTING——气割OC-F——flux cutting——熔剂切割OC-P——metal powder cutting——金属熔剂切割OFC——oxyfuel gas cutting——氧燃气切割CFC-A——oxyacetylene cutting——氧乙炔切割CFC-H——oxyhydrogen cutting——氢氧切割CFC-N——oxynatural gas cutting——氧天然气切割CFC-P——oxypropanne cutting——氧丙酮切割OAC——oxygen arc cutting——氧气电弧切割OG——oxygen gouging——气刨OLC——oxygen lance cutting——氧矛切割AC——ARC CUTTING——电弧切割CAC——carbon arc cutting——碳弧切割CAC-A——air carbon arc cutting——空气碳弧切割GMAC——gas metal arc cutting——熔化极气体保护电弧切割GTAC——gas tungsten arc cutting——钨极气体保护电弧切割PAC——plasma arc cutting——等离子弧切割SMAC——shielded metal arc cutting——焊条电弧切割HIGH ENERGY BEAM CUTTING——高能束切割EBC——electron beam cutting——电子束切割LBC——laser beam cutting——激光切割LBC-A——air——空气激光切割LBC-EV——evaporative——蒸气激光切割LBC-IG——inert gas——惰性气体激光切割LBC-O——oxygen——氧气激光切割11 AUT indication (自动超声探问题)12 BAD FILM QUALITY (成片质量差)13 Dent (凹坑/摔坑)14 Internal Defects (内部缺陷)15 Lack Of Penetration (未焊透)20 OVERLAP (焊瘤)21 OFFSET (错边)22 Other Defects (其它缺陷)23 Porosity (气孔)飞溅：spatter24 Slag (焊渣)25 SCRATCH (划痕)31 Rust (锈蚀)32 Mis-Alignment (焊偏)33 Crack (裂纹)34 Crater (弧坑)35 Lap (折叠)36 Lamination (母材分层)37 Seam (重皮)38 Defect not repaired (缺陷未补)40 DWTT (落锤不合)42 OD Oversize (管径大)43 OD Undersize (管径小)44 Impact Test Not Passed (冲击不合)45 Welding Interruption (内外断)46 Manual UT (手动超声探问题)47 Bevel Damage (坡口损坏)49 Scuff Marks (磨损痕迹)50 Weld Damage (焊缝缺陷)51 Weld Spatter (焊接飞溅)52 Pipe Marking (管子标识问题)67 Repair Areas are more than Allowed (补焊超处)。
焊接专业词汇
焊接专业词汇－英中对照weldable adj. 可焊的weldless adj. 无焊缝的weldment n. 焊(接)件double-bevel groove weld 双斜边坡口焊缝, K形坡口焊缝butt weld 对接焊缝groove weld 坡口焊contour weld 特形焊接automatic spot weld 自动点焊法explosive weld 爆炸焊接gas-pressure weld 气压焊concave fillet weld 凹角焊downhand weld 平焊缝carbon arc weld 碳极弧焊braze welding 硬焊, 铜焊, 钎焊air-acetylene welding空气-乙炔焊接argon arc welding 氩弧焊automatic slag-pool welding 自动电渣焊aircomatic welding 自动调弧氩弧焊, 惰性气体保护金属极弧焊aluminothermic welding 铸焊, 铝热剂焊接butt welding 对接焊, 对焊austenite welding 不锈钢(焊条)焊接automatic submerged arc welding 自动埋弧焊argon shielded arc welding 氩护电弧焊weld all around围焊weld appearance驾吨焊缝外观welding powder 焊粉weldable steel可焊钢;焊接钢weldable copper可焊复合铜板non-weldable steel不可焊接的钢high strength weldable aluminium alloy高强度可焊铝合金weldable可焊的non-weldable不可焊接的weldable strain gauge悦焊接式应变计weldbonding粘焊(指电阻点焊与用粘胶粘接相结合的焊接)welddecay[冶]焊接区晶间腐蚀welded all around（round）沿周边焊接的lap welded casing搭焊套管welded aluminum alloy（WAA）焊制铝合金welded and expansion joint焊接加胀接法welded and rolled tube joint焊胀welded armor焊接甲板welded attachment焊接附件welded austenitic stainless steel pipe焊接奥氏体不锈钢钢管welded bellows焊接波纹管welded body焊接车身;焊体welded bond焊接轨隙连接器welded cap焊接管封头projection welded cap凸焊帽;有凹凸的焊帽welded bridge焊接桥, 焊接桥梁welded casing焊接套管welded case焊接机匣helically-welded case螺旋焊接壳体welded chain焊接链welded cathode焊接阴极welded connection焊接合,焊接头,焊接联结shop-welded connection厂焊接头welded construction 焊接结构all-welded construction全焊结构welded contact rectifier熔接整流器welded corner joint角焊接welded crossing焊接断面welded digester焊接蒸煮锅welded elbow焊接机械肘, 焊接弯头welded encapsulation焊接封装welded ends焊接连接端welded fin tube焊片式翅片管welded fissure焊接裂缝,焊合的裂缝, 焊接裂纹welded fitting焊接式管接头welded flange焊接法兰;焊接翼缘manhole with common welded flange平焊法兰人孔manhole with butt welded flange对焊法兰人孔handhole with butt welded flange对焊法兰手孔welded flat head焊接式平盖welded frame焊接骨架, 焊接车架, 焊接隔框tubular welded frame scaffold管状焊接框架式脚手架welded frog焊接辙叉welded gasket焊接垫tie-in weld管段间焊接powder weld process粉末焊接法intermittent fillet weld断续角焊缝edge weld端接焊缝tack weld定位焊backing run; backing weld打底焊道strapped weld; strapped joint搭板对接焊缝strength weld承载焊缝lap fillet welding搭接角焊overlap welding; lap welding搭接焊magneticetic pulse welding磁力脉冲焊flywheel type friction welding; inertia welding储能摩擦焊stored energy welding储能焊percussion welding冲击焊workshop welding车间焊接explosive welding爆炸焊接blasting welding factory爆破焊接厂welded eye焊眼welded elbow; welded ell焊接直角弯头welded nut焊接螺母welded tank焊接罐welded pipe焊接管ratio-frequency welded tube高频焊管furnace butt-welded pipe对接炉焊管hammer welded pipe锻焊管lap welded casing搭焊套管concave fillet weld凹形角焊缝automatic spot weld自动点焊法butt weld对接焊缝carbon arc weld碳极弧焊concave fillet weld凹角焊contour weld特形焊接double-bevel groove weld双斜边坡口焊缝, K形坡口焊缝downhand weld平焊缝explosive weld爆炸焊接gas-pressure weld气压焊groove weld坡口焊heliarc weld氦弧焊inert gas carbon-arc weld惰性气体保护碳弧焊接inert gas metal-arc weld惰性气体保护金属极弧焊intermittent weld间断焊缝lap(seam) weld搭接焊缝; 搭接焊laser weld激光焊multiple-electrode submerged arc weld多电极埋弧焊multiple-pass weld多道焊缝non-pressure weld熔焊, 不加压焊接overhead fillet weld仰焊角焊缝oxyacetylene weld氧[乙]炔焊, 气焊oxygen weld氧气焊接, 气焊projection weld凸焊resonance butt weld谐振式对接焊scarf weld斜面焊接, 两端搭接焊, 嵌接焊semi-automatic arc weld半自动电弧焊shot weld点焊fusion pressure welding熔化压接fusion thermit welding熔化铅热焊gas-electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊, 熔化极气体保护焊gas shielded arc welding气体保护焊, 气体保护弧焊gas shielded magnetic flux arc welding磁性焊剂气体保护焊gas torch welding炬焊gas tungsten arc welding钨电极惰性气体保护焊girth welding环缝焊接gravity welding重力焊, 重力式电弧焊hammer welding锻接hard facing arc welding表面加硬电弧焊heated-tool welding热烙铁焊接helium shielded welding氦气保护焊接hidden arc welding潜弧焊, 埋弧焊high-frequency induction welding高频感应焊接horizontal fillet welding水平角焊接horizontal-rolled-position welding滚动水平焊, 水平转动焊接hydrogen atomic welding原子氢焊接induction resistance welding感应电阻焊接indirect spot welding间接点焊inert gas shielded-arc welding惰性气体保护焊inert gas tungsten arc welding钨板惰性气体保护焊inertial welding惯性焊接jump welding丁字形焊。
焊接专业术语中英文对照整理
焊接专业术语中英文对照整理机械——焊接专业术语中英文对照（郭运）整理1Single 单面的2V—groove V型坡口3Joint 焊接接头4Edges overlap 接头形式5Butt 对接6T T型焊接7Fillet 角焊缝8Edge 端接9Corner 角接10Radius 半径11Joint root 焊接根部12Bevel angle 削边角度13Groove angle 坡口角度14Root face 根部钝边15Groove face 坡口面16Plug weld 塞焊17Spot weld 点焊18Seam weld 缝焊19Slot weld 槽焊20Double—flare—bevel—groove K型坡口焊缝21Single—flare—V 单面V型22Edge flange 翻边端接23Corner flange 卷边端接24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝27Slot weld 槽焊缝28Spot weld 点焊缝29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚40Toe 焊趾41Buildup 堆焊42Weld reinforcement 焊缝加强高43Effective throat 有效焊喉44Concave weld 凹形焊缝45Convex weld 凸形焊缝46Unequal leg fillet 不等脚角焊47Oversize weld 大尺寸焊缝48Depth of fusion 熔合深度49Depth of penetration 熔透深度50Root penetration 根部熔深51Joint penetration 接头熔深52Weld interface 焊缝分界面53Diameter of weld at point of contact 焊缝在接触点上的直径54Thickness 厚度55Tail 尾部56Arrow 箭头57Reference line 参考线58Arrow side 箭头一边59Weld symbol 焊缝符号60Near side 近侧61Arrow side 箭头侧62Far side 远侧63Other side 另一侧64Put the weld on either—side 在任意一侧施焊65There is noside significance 没有方向区别66Edge flange 双卷边67Corner flange 单卷边68Weld size 焊缝尺寸69Effective throat 有效厚度70Root opening 根部间隙71Full penetration double bevel—groove weld K形坡口全焊透焊缝72Full penetration double V—groove weld 双V形坡口全焊透焊缝73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝74Partial penetration double V—groove weld 双V形坡口部分焊透焊缝75Bevel groove 削边坡口76Flare groove 喇叭形坡口77Flange groove 卷边坡口78V—groove V形坡口79Staggered intermittent fillet weld 交错间断角焊缝80Chain intermittent fillet weld 链状间断角焊缝81Segmented fillet weld 分段角焊缝82Pitch distance 间距83Depth of filling 填充深度84Slot weld width 槽焊缝宽度85Plug weld diameter 塞焊缝的直径86Angle of countersink 深孔角度87A dimension to the right of the symbol 在符号右边的尺寸88A dimension of the required suggest diameter 所要求的直径尺寸89A value for the required shear strength per spot 每点所要求的剪切强度值90Spot weld size 点焊缝尺寸91Spot weld length 点焊缝的长度92Number of spot required 所要求的点的数量93Pitch distance between adjacent spots 两个相邻点的间距94Reference line 参考线95Melt—through of weld from other side 焊缝在另一侧熔透96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝97Single bevel—groove weld with back weld 背面焊的单边坡口焊缝98Single bevel—groove weld with backing weld 带垫板的V 形坡口焊缝99Single bevel—groove weld with back weld背面焊的V形坡口焊缝100Square groove 直边坡口101Skewed groove 斜坡口102Sloped groove 倾斜坡口103Scarf 斜嵌接104Gas metal arc spot weld 气体保护点焊105Resistance spot weld 电阻点焊106Gas metal arc seam weld 气体保护滚焊缝107Resistance seam weld 电阻滚焊缝108Gas metal arc slot weld 气体保护槽焊缝109The type of electrode to use 所要求焊条形式110The weld quality standard 焊缝质量标准111The weld procedure to use 所用的焊接程序112Codes 规范113Drawing 图纸114Specifications 技术要求115Contracts 合同116General 一般注解117Local 局部注解118The point for lifting an object 吊装一物体的点119Filler metals 填充金属120Pressure vessel fabrication 压力容器制造121Be as simple as possible 尽可能简单122Welder 焊工123Code body 规范本身124Shielded metal arc 手工电弧焊125Submerged arc 埋弧焊126Face bend 面弯127Root bend 背弯128Side bend 侧弯129Nick break 缺口破坏130Tensile 拉伸131Monitoring production welding 监视生产中的焊接132Strength 强度133Toughness 韧性134Hardness 硬度135Ductility 延展性136Compressive 压缩137Impact 冲击138Fatigue 疲劳139Undercut 咬边140Overlap 焊瘤141Cracking 裂纹142Porosity 气孔143Ultimate tensile strength 极限拉伸强度144Percent elongation 延伸率145Percent reduction of area 断面收缩率146Impact strength 冲击强度147Yield strength 屈服强度148Brinell 布氏149Vickers 韦氏150Rockwell 洛氏151Knoop 努氏152Fatigue test 疲劳试验153T ensile test 拉伸试验154Micro--hardness test 显微硬度试验155Charpy impact test 夏比冲击试验156Soundness test 致密性测试157Fillet break 角焊缝断裂158Metallographic 金相159Transverse fillet weld shear test 横向角焊缝剪切试验160Quality of the fractured weld 焊缝端口的质量161Ductility of the weld metal 焊缝金属的延展性162Impact strength of the weld 焊缝的冲击强度163Tensile strength of the base metal 母材的拉伸强度164Weld—ability 可焊性165Scratches caused by improper handling 由不适当的处理导致的划痕166Incomplete fusion 未熔合167Distortion 变形168Slag inclusions 夹渣169Vibratory stress relief 振动消除应力170External restraint 外部拘束171Thermal stress relief 热消除应力172Peening 锤击173Annealing 退火174Quenching 淬火175Tempering 回火176Normalizing 正火177Decrease current 降低电流178Decrease voltage 降低电压179Increase travel speed 加快焊接速度180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术181Result in a wider heat—affected zone hardness导致热影响区更宽182Produce a lower heat—affected zone hardness 降低热影响区硬度183Slow down the cooling rate 降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone 减少在热影响区形成马氏体的倾向185Stress relief 消除应力186Crater crack 弧坑裂纹187SMAW 手动电弧焊188PAW 等离子焊189FCAW 药芯焊190SAW 埋弧焊191Underfill 未焊满192Excess convexity 太凸193Excess weld reinforcement 焊缝余高太高194Overfill 过充195Scratch start 擦伤196Arc strike 引弧烧伤197Tungsten inclusion 夹钨198Lamination 分层199Lamellar tear 片状撕裂200Seam 划伤201Pipe shrinkage 缩孔202Longitudinal crack 纵向裂纹203Transverse crack 横向裂纹204Underbead crack 焊道中裂纹205T oe crack 焊趾裂纹206Root crack 根部裂纹207Base metal crack 母材裂纹208Before welding 焊接前209During welding 焊接时210After welding 焊接后211Waiting time 等待时间212Penetrating time 渗透时间213Soak time 吸入时间214Dwell time 驻留时间215AC 交流电216DC 直流电217DCEP 直流反接218。
焊接专业英汉词典
焊接专业英汉词典熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequence/deposition sequence焊缝倾角weld slope/inclination of weld axis焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊down-hand welding/flat position welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
如水平固定管所进行的环缝焊接向下立焊vertical down welding/downward welding in the vertical position向上立焊vertical up welding/upward welding in the vertical position倾斜焊inclined position welding上坡焊upward welding in the inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the down-hand position/fillet welding in the flat position平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊foreward welding (英国)/ forehand welding (美国) 后倾焊backward welding(英国)/ backhand welding(美国) 分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding右焊法rightward welding/backhand welding挑弧焊whipping method自动焊automatic welding手工焊manual welding/hand welding车间焊接shop welding工地焊接site welding(英国)/ field welding (美国)拘束焊接restraint welding堆焊surfacing/building up/overlaying隔离层堆焊buttering端部周边焊boxing/end return返修焊rewelding补焊repair welding塞焊plug welding槽焊slot welding衬垫焊welding with backing焊剂垫焊welding with flux backing窄间隙焊narrow-gap welding强制成形焊enclosed welding脉冲电弧焊pulsed are welding电弧点焊arc spot welding螺柱焊stud welding热风焊hot gas welding高能焊high grade energy welding固态焊接solid-state welding单面焊双面成形one-side welding with back formation 焊接条件welding condition焊接工艺参数welding parameter极性polarity正接electrode negative/straight polarity反接electrode positive/reversed polarity运条方式manipulation of electrode焊接电流welding current焊接电流增加时间welding current upslope time焊接电流衰减时间welding current downslope time电流密度current density短路电流short circuit current脉冲电流pulse level/pulse current level脉冲电流幅值pulse current amplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy input热输入heat input预热preheat后热postheat焊后热处理posweld heat treatment/postheat treatment 预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element)坡口groove坡口面groove face坡口面角度angle of bevel (英国)/ bevel angle (美国)坡口角度included angle(英国)/groove angle(美国)坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国)/root opening (美国)根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove with root face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U grooveVY形坡口single compound angle groove带钝边J形坡口single J groove带钝边双J形坡口double J groove单边V形坡口single bevel groove双V形坡口double V groove不对称双V形坡口asymmetric double V groove双单边V形坡口double bevel groove/K groove带垫板V形坡口V groove with backing/ single V groove with backing喇叭形坡口flare groove锁底坡口single bevel groove with backing locked坡形板边tapered edge焊缝weld接逢seam焊缝符号welding symbol焊缝金属weld metal填充金属filler metal熔敷金属deposited metal焊缝表面weld face/ face of weld焊缝背面back of weld焊缝轴线axis of weld焊缝尺寸size of weld焊缝宽度weld width/ width of weld焊缝长度weld length/ length of weld焊缝有效长度effective length of weld焊缝厚度throat depth/ throat thickness焊缝计算厚度theoretical throat焊缝实际厚度actual throat熔深penetration/ depth of penetration焊缝成形appearance of weld焊缝成形系数form factor of weld余高reinforcement/ excess weld metal背面余高root reinforcement削平焊缝flush weld/ weld machined flush对接焊缝butt weld角焊缝fillet焊脚leg/ fillet weld leg角焊缝断面形状profile of fillet weld平形角焊缝flat fillet凸形角焊缝convex fillet weld凹形角焊缝concave fillet weld角焊缝凹度concavity侧面角焊缝side fillet weld/ fillet weld in parallel shear 正面角焊缝front fillet weld/ fillet weld in normal shear 立角焊缝fillet weld in the vertical position横角焊缝fillet weld in the horizontal position平角焊缝fillet weld in the flat position斜角焊缝oblique fillet weld连续焊缝continuous weld断续焊缝intermittent weld连续角焊缝continuous fillet weld断续角焊缝intermittent fillet weld交错断续角焊缝staggered intermittent fillet weld并列断续角焊缝chain intermittent fillet weld端接焊缝edge weld卷边焊缝flanged edge weld塞焊焊缝plug weld纵向焊缝longitudinal weld横向焊缝transverse weld环行焊缝girth weld/ circumferential weld螺旋形焊缝spiral weld/ helical weld密封焊缝seal weld承载焊缝strength weld联系焊缝connective weld定位焊缝tack weld焊道bead/ run/ pass焊波ripple焊根weld root/ root of weld焊趾weld toe/ toe封底焊道sealing run (after making main weld)/ back weld打底焊道backing weld (before making main weld)/ back weld根部焊道root pass/ root run填充焊道filling bead盖面焊道cosmetic bead/ cover pass回火焊道temper bead/ annealing bead熔透焊道penetration bead焊层layer焊接接头welded joint接头形状joint geometry等强匹配接头equalmatching weld joint低强匹配接头undermatching weld joint超强匹配接头overmatching weld joint接头根部root of joint对接接头butt jointI形对接接头square butt jointV形对接接头single V butt jointU形对接接头single U butt jointJ形坡口接头single J butt joint双V形对接接头double V butt joint双单边V形对接接头double bevel butt joint/ K groove butt joint 带钝边U形对接接头double U butt joint带钝边J形坡口接头double J joint角接接头corner jointT形接头T joint斜T形接头inclined T joint十字接头cruciform joint/ cross-shaped joint三联接头joint among three members搭接接头lap joint套管接头muff joint/ sleeve joint双盖板接头double strapped joint盖板接头strapped joint端接接头edge joint卷边接头flanged edge joint锁底对接接头lock butt joint斜对接接头oblique butt joint混合接头mixed joint/ composite joint有间隙接头open joint无间隙接头closed joint焊接电弧welding arc电弧形态arc shape电弧物理行为arc physics behaviour引弧striking arc引弧电压striking voltage电弧气氛arc atmosphere阴极cathode热阴极hot cathode冷阴极cold cathode阴极斑点cathode spot阴极区cathode region阴极区电场强度intensity of the electric field in the cathode region 阴极压降cathode drop阳极anode阳极斑点anode spot斑点压力spot pressure阳极区anode region阳极区电场强度intensity of the electric field in the anode region 阳极压降anode drop弧柱arc column/ arc stream弧柱压降voltage drop in arc column弧柱电位梯度potential gradient in the arc column弧焰arc flame弧心arc core硬电弧forceful arc/ hard arc软电弧soft arc旋转电弧rotating arc脉冲电弧pulsed arc脉冲喷射电弧pulsed spray arc起皱现象puckering phenomena起皱电弧puckering arc起皱临界电流puckering critical current间接电弧indirect arc压缩电弧compressive arc磁控电弧magnetic controlling arc电弧力arc force电磁力electromagnectic force电磁收缩效应pinch effect电弧飘移wandering of arc电弧稳定性arc stability电弧静特性static characteristic of arc电弧动特性dynamic characteristic of arc最小电压原理principle of minimum voltage电弧挺度arc stiffness电弧偏吹arc blow磁偏吹magnetic blow阴极清理作用cleaning action of the cathode电弧自身调节arc self-regulation挖掘作用digging action极性效应polarity effect熔滴droplet熔滴比表面积specific surface of droplet熔滴过渡metal transfer过度频率transition frequency粗滴过渡globular transfer; drop transfer短路过渡short circuiting transfer喷射过渡spray transfer旋转喷射过渡rotating spray transfer脉冲喷射过渡pulsed spray transfer爆炸过渡explosive transfer渣壁过渡flux wall guided transfer熔池molten pool沸腾状熔池boiling molten pool弧坑crater熔渣slag渣系slag system渣系相图slag system diagram碱性渣basic slag酸性渣acid slag碱度basicity酸度acidity长渣long slag短渣short slag粘性熔渣viscous slag氧化物型熔渣oxide melting slag盐型熔渣salt melting slag盐-氧化物型熔渣salt-oxide melting slag熔渣流动性fluidity of the slag; slag fluidity熔渣solidified slag多孔焊渣porous slag玻璃状焊渣vitreous slag自动脱落焊渣self-releasing slag脱渣性slag detachability焊接设备welding equipment; welding set焊机welding machine; welder电焊机electric welding machine; electric welder焊接电源welding power source焊接热循环weld thermal cycle焊接温度场field of weld temperature; weld temperature field准稳定温度场quasi-stationary temperature field焊接热源welding heat source点热源point heat source线热源linear heat source面热源plane heat source瞬时集中热源instantaneous concentration heat source热效率thermal efficiency热能集中系数coefficient of heat flow concentration峰值温度peak temperature瞬时冷却速度momentary cooling rate冷却时间cooling time置换氧化substitutionary oxydation扩散氧化diffusible oxydation脱氧desoxydation先期脱氧precedent desoxydation扩散脱氧diffusible desoxydation沉淀脱氧precipitation desoxydation扩散氢diffusible hydrogen初始扩散氢initial diffusible hydrogen100℃残余扩散氢diffusible hydrogen remained at 100℃残余氢residual hydrogen去氢dehydrogenation去氢热处理heat treatment for dehydrogenation脱硫desulphurization脱磷dephosphorization渗合金alloying微量合金化microalloying一次结晶组织primary solidification structure二次结晶组织secondary solidification structure联生结晶epitaxial solidification焊缝结晶形态solidification mode in weld-bead结晶层状线ripple多边化边界polygonization boundary结晶平均线速度mean solidification rate针状铁素体acicular ferrite条状铁素体lath ferrite侧板条铁素体ferrite side-plate晶界欣素体grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite 粒状贝氏体granular bainite板条马氏体lath martensite过热组织overheated structure魏氏组织Widmannst?tten structureM-A组元martensite-austenite constituent焊件失效分析failure analysis of weldments冷裂判据criterion of cold cracking冷裂敏感系数cold cracking susceptibity coefficient 脆性温度区间brittle temperature range氢脆hydrogen embrittlement层状偏析lamellar segregation愈合healing effect断口金相fractography断口fracture延性断口ductile fracture韧窝断口dimple fracture脆性断口brittle fracture解理断口cleavage fracture准解理断口quasi-cleavage fracture氢致准解理断口hydrogen-embrittlement induced 沿晶断口intergranular fracture穿晶断口transgranular fracture疲劳断口fatigue fracture滑移面断口glide plane fracture断口形貌fracture apperance断口试验fracture test宏观断口分析macrofractography放射区radical zone纤维区fibrous zone剪切唇区shear lip aone焊接性weldability使用焊接性service weldability工艺焊接性fabrication weldability冶金焊接性metallurgical weldability热焊接性thermal weldability母材base metal; parent metal焊接区weld zone焊态as-welded (AW)母材熔化区fusion zone半熔化区partial melting region未混合区unmixed zone熔合区bond area熔合线weld junction (英)；bond line (美)热影响区heat-affected zone (HAZ)过热区overheated zone粗晶区coarse grained region细晶区fine grained region过渡区transition zone硬化区hardened zone碳当量carbon equivalent铬当量chromium equivalent镍当量nickel equivalent舍夫勒组织图Schaeffler's diagram德龙组织图Delong’s diagram连续冷却转变图（CCT图）continuous cooling transformation 裂纹敏感性cracking sensibility焊接裂纹weld crack焊缝裂纹weld metal crack焊道裂纹bead crack弧坑裂纹crater crack热影响区裂纹heat-affected zone crack纵向裂纹longitudinal crack横向裂纹transverse crack微裂纹micro-crack; micro-fissure热裂纹hot crack凝固裂纹solidification crack晶间裂纹intercrystalline crack穿晶裂纹transcrystalline crack多边化裂纹polygonization crack液化裂纹liquation crack失延裂纹ductility-dip crack冷裂纹cold crack延迟裂纹delayed crack氢致裂纹hydrogen-induced crack焊道下裂纹underbead crack焊根裂纹root crack焊趾裂纹toe crack锯齿形裂纹chevron cracking消除应力处理裂纹stress relief annealing crack (SR crack)再热裂纹reheat crack焊缝晶间腐蚀weld intercryctalline corrosion刀状腐蚀knife line attack敏化区腐蚀weld decay层状撕裂lamellar tearing焊接性试验weldability裂纹试验cracking testIIW裂纹试验IIW cracking testY形坡口裂纹试验slit type cracking test分块形槽热裂纹试验segmented circular groove cracking test H形裂纹试验H-type cracking test鱼骨形裂纹试验fishbone cracking test指形裂纹试验finger (cracking) testT形裂纹试验Tee type cracking test环形槽裂纹试验circular-groove cracking test可调拘束裂纹试验varestraint testBWRA奥氏体钢裂纹试验BWRA cracking test for austenitie steel圆棒裂纹试验bar type cracking test; round bar cracking test里海裂纹试验Lehigh restraint cracking test圆形镶块裂纹试验circular-path cracking test十字接头裂纹试验cruciform cracking testZ向窗口拘束裂纹试验Z-direction window type restraint cracking test G-BOP焊缝金属裂纹试验G-BOP weld metal crack test巴特尔焊道下裂纹试验Battelle type underbead cracking testU形拉伸试验U-tension test缪雷克期热裂纹试验Murex hot cracking test菲斯柯裂纹试验FISCO (type) cracking testCTS裂纹试验controlled thermal severity拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test刚性拘束裂纹试验（RRC试验）rigid restraint cracking test插销试验implant testTigamajig 薄板焊接裂纹试验Tigamajing thin plate cracking test焊道纵向弯曲试验longitudinal-bead test柯麦雷尔弯曲试验Kommerell bead bend test肯泽尔弯曲试验Kinzel test缺口弯曲试验notch bend test热朔性试验hot-ductility test热影响区冲击试验impact test of HAZ热影响区模拟试验synthetic heat-affected zone test最高硬度试验maximum hardness test落锤试验NRL (Naval Research Laboratory)测氢试验Hydrogen test焊接材料电极焊接材料welding consumables电极electrode熔化电极consumable electrode不熔化电极nonconsumable electrode钨电极tungsten electrode焊丝welding wire. Welding rod实心焊丝solid wire渡铜焊丝copper-plating welding wire自保护焊丝self-shielded welding wire药芯焊丝flux-cored wire复合焊丝combined wire堆焊焊丝surfacing welding rod填充焊丝filler wire焊条electrode/ covered electrode焊芯core wire药皮coating (of an electrode)/ covering (of an electrode)涂料coating flux/coating material造气剂gas forming constituents造渣剂slag forming constituents合金剂alloying constituent脱氧剂dioxidizer稳弧剂arc stabilizer粘接剂binder水玻璃water glass水玻璃模数modules of water glass酸性焊条acid electrode高钛型焊条high titania (type) electrode钛钙型焊条lime titania type electrode钛铁矿形焊条ilmenite type electrode氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode高纤维素型焊条high cellulose (type) electrode石墨型焊条graphite type electrode碱性焊条basic electrode/ lime type covered electrode低氢型焊条low hydrogen type electrode高韧性超低氢焊条high toughness super low hydrogen electrode奥氏体焊条austenitic electrode铁素体焊条ferritic electrode不锈钢焊条stainless steel electrode珠光体耐热钢焊条pearlitic heat resistant steel electrode低温钢焊条low temperature steel electrode/ steel electrode for low temperature 铝合金焊条aluminum alloy arc welding electrode铜合金焊条copper-alloy arc welding electrode铜芯铸铁焊条cast iron electrode with steel core纯镍铸铁焊条pure nickel cast iron electrode球墨铸铁焊条electrode for welding spheroidal graphite cast iron铸芯焊条electrode with cast core wire镍基合金焊条nickel base alloy covered electrode蒙乃尔焊条Monel electrode纯铁焊条pure iron electrode渗铝钢焊条alumetized steel electrode高效率焊条high efficiency electrode铁粉焊条iron powder electrode底层焊条backing welding electrode深熔焊条deep penetration electrode重力焊条gravity electrode立向下焊条electrode for vertical down position welding节能焊条saving energy electrode水下焊条underwater welding electrode耐海水腐蚀焊条seawater corrosion resistant steel electrode低尘低毒焊条low-fume and harmfulless electrode/low-fume and low-toxic electrode堆焊焊条surfacing electrode耐磨堆焊焊条hardfacing electrode钴基合金堆焊焊条cobalt base alloy surfacing electrode碳化钨堆焊焊条tungsten carbide surfacing electrode高锰钢堆焊焊条high manganese steel surfacing electrode双芯焊条twin electrode绞合焊条stranded electrode编织焊条braided electrode双层药皮焊条double coated electrode管状焊条flux-cored electrode气渣联合保护型药皮semi-volatile covering焊条工艺性usability of the electrode/ technicality of the electrode焊条使用性running characteristics of an electrode/ operating characteristics of an electrode 焊条熔化性melting characteristics of an electrode焊条直径core diameter焊条偏心度eccentricity (of an electrode)药皮重量系数gravity coefficient of coating焊条药皮含水量percentage of moisture for covering焊条夹吃持端bare terminal (of an electrode)焊条引弧端striking end (of an electrode)焊剂welding flux/ flux熔炼焊剂fused flux粘结焊剂bonded flux烧结焊剂sintered flux/ agglomerated flux窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding低氢型焊剂low hydrogen type flux高速焊剂high speed welding flux无氧焊剂oxygen-free flux低毒焊剂low poison flux磁性焊剂magnetic flux电弧焊arc welding直流电弧焊direct current arc welding交流电弧焊alternating current arc welding三相电弧焊three phase arc welding熔化电弧焊arc welding with consumable金属极电弧焊metal arc welding不熔化极电弧焊arc welding with nonconsumable碳弧焊carbon arc welding明弧焊open arc welding焊条电弧焊shielded metal arc welding (SMAW)重力焊gravity welding躺焊fire cracker welding电弧堆焊arc surfacing自动堆焊automatic surfacing躺板极堆焊surfacing by fire cracker welding带极堆焊surfacing with band-electrode振动电弧堆焊vibratory arc surfacing耐磨堆焊hardfacing埋弧焊submerged arc welding (SAW)多丝埋弧焊multiple wire submerged arc welding纵列多丝埋弧焊Tandem sequence (submerged-arc welding)横列多丝埋弧焊series submerged arc welding (SAW-S)横列双丝并联埋弧焊transverse submerged arc welding热丝埋弧焊hot wire submerged-arc welding窄间隙埋弧焊narrow-gap submerged arc welding弧压反馈电弧焊arc voltage feedback controlling arc welding自调节电弧焊self-adjusting arc welding适应控制焊接adaptive control welding焊剂层burden; flux layer气体保护电弧焊gas shielded arc welding保护气体protective atmosphere惰性气体inert-gas活性气体active-gas惰性气体保护焊inert-gas (arc) welding氩弧焊argon arc welding熔化极惰性气体保护电弧焊metal inert-gas arc welding钨极惰性气体保护电弧焊tungsten inert-gas arc welding钨极氢弧焊argon tungsten arc welding脉冲氢弧焊pulsed argon arc welding熔化极脉冲氢弧焊argon metal pulsed arc welding钨极脉冲氢弧焊argon tungsten pulsed arc welding热丝MIG焊hot wire MIG welding热丝TIG焊hot wire TIG welding氨弧焊helium-arc welding活性气体保护电弧焊metal active-gas arc welding混合气体保护电弧焊mixed gas arc welding二氧化碳气体保护电弧焊carbon-dioxide arc welding; CO2 arc welding 细丝CO2焊CO2 arc welding with thin wire粗丝CO2焊CO2 arc welding with thick wire磁性焊剂CO2焊unionarc welding药芯焊丝CO2焊arcos arc process; dual shield arc welding气电立焊electro-gas (arc) welding氮弧焊nitrogen-arc welding水蒸气保护电弧焊water vapor arc welding原子氢焊atomic hydrogen welding冲器室中电弧焊controlled atmosphere arc welding旋转电弧焊rotating arc welding短路过渡电弧焊short circuiting arc welding焊丝横摆频率weaving speed of wire焊丝停摆时间electrode keep time of slider等离子弧焊plasma arc welding (PAW)等离子弧plasma arc等离子流plasma jet转移弧transferred arc非转移弧nontransferred arc联合型等离子弧combined plasma arc主弧main arc维弧pilot arc维弧电流pilot arc surrent双弧现象double arcing双弧临界电流critical current of double arcing等离子弧焊枪plasma (welding) torch压缩喷嘴constricting nozzle单孔喷嘴single port nozzle多孔喷嘴multiport nozzle压缩喷嘴孔径orifice diameter孔道长度orifice throat length孔道比orifice throat ratio等离子气plasma gas; orifice gas电极内缩长度electrode setback小孔效应keyhole effect小孔型等离子弧焊keyhole-mode welding熔透型等离子弧焊fusion type plasma arc welding大电流等离子弧焊high-current plasma arc welding中电流等离子弧焊intermediate-current plasma arc welding 小电流等离子弧焊low-current plasma arc welding微束等离子弧焊micro-plasma arc welding交流等离子弧焊AC plasma arc welding脉冲等离子弧焊pulsed plasma arc welding等离子弧堆焊plasma arc surfacing热丝等离子弧堆焊hot wire plasma arc surfacing粉末等离子弧堆焊plasma arc powder surfacing等离子-熔化极惰性气体保护电弧焊plasma MIG welding 转移弧电源transferred arc power supply非转移弧电源nontransferred arc power supply电弧焊设备arc welding equipment电弧焊机arc welding machine直流弧焊机DC arc welding machine交流弧焊机AC arc welding machine交直流两用弧焊机AC/DC arc welding machine单站弧焊机single operator arc welding machine多站弧焊机multi-operator arc welding set固定式弧焊机stationary arc welding machine移动式弧焊机portable arc welding machine台式弧焊机bench arc welding machine内燃机驱动式弧焊机combustion engine driven arc welding set电动机驱动式弧焊机motor driven arc welding set熔化极弧焊机arc welding machine using a consumable electrode不熔化极弧焊机arc welding machine using a non-consumable electrode脉冲弧焊机pulsed arc welding machine气体保护弧焊机gas shielded arc welding machine氩弧焊机argon arc welding machine二氧化碳弧焊机CO2 arc welding machine钨极惰性气体保护弧焊机tungsten inert-gas welding machine熔化仍惰性气体保护弧焊机metal inert-gas welding machine气电立焊机electrogas (arc) welding machine等离子弧焊机plasma arc welding machine微束等离子弧焊机micro-plasma welding equipment原子氢焊机atomic hydrogen welding apparatus埋弧焊机submerged arc welding machine弧焊电源arc welding power source直流弧焊电源DC arc welding power source交流弧焊电源AC arc welding power source交直流两用弧焊电源AC/DC arc welding power source脉冲弧焊电源pulsed arc welding power source上升特性弧焊电源rising characteristic arc welding power source平特性弧焊电源constant –voltage arc welding power source下降特性弧焊电源dropping characteristic arc welding power source垂降特性弧焊电源constant-current arc welding power source多特性弧焊电源slope-controlled arc welding power source逆变式焊接电源inverter welding power source晶体管弧焊电源transistor arc welding power source电源动特性dynamic characteristic电源外特性external characteristic弧焊变压器arc welding transformer弧焊整流器arc welding rectifier硅弧焊整流器silicon arc welding rectifier晶闸管弧焊整流器SCR arc welding rectifier; arc welding silicon controlled rectifier 脉冲弧焊整流器pulsed arc welding rectifier弧焊发电机arc welding generator焊车welding tractor焊接机头welding head行走机构traveller送丝机构wire feeder等速送丝方式constant wire-feed system变速送丝方式alternate wire-feed system跟踪装置tracer焊丝盘wire reel焊钳electrode holder焊枪welding gun电极夹electrode holder导电嘴tip; contact tube喷嘴nozzle焊剂漏斗flux-hopper高频振荡器oscillator; HF unit脉冲引弧器pulsed arc starter; surge injector脉冲稳弧器pulsed arc stabilizer脉冲激弧器pulsed arc exciter输出电抗器out put reactor镇定变阻器ballast rheostat直流分量抑制器direct current suppressor焊接回路welding circuit额定焊接电流rated welding current焊接电流调节范围range of welding current regulation 空载电压open circuit voltage(no load voltage)约定负载电压conventional load voltage负载持续率duty cycle额定负载持续率rated duty cycle; standard service手工弧焊机manual arc welding machine电焊渣electroslag welding (ESW)手工电渣焊manual electroslag welding丝极电渣焊electroslag welding with wire electrode板极电渣焊electroslag welding with plate electrode熔嘴电渣焊electroslag welding with consumable nozzle 管极电渣焊electroslag welding with tube electrode窄间隙电渣焊narrow-gap electroslag welding电渣堆焊electroslag surfacing电渣焊机electrosalg welding machine熔嘴consumable nozzle; consumable wire钢档板steel shoe钢冷却板Cu-cooling plate铜滑板copper shoe渣池slag bath渣池深度depth of slag bath渣池电压voltage of slag bath电渣过程稳定性electroslag process stability焊丝间距distance between welding wires电子束焊electron beam welding (EBW)脉冲电子束焊pulsed electron beam welding加速电压acceleration voltage/ operating voltage电子束电流beam current电子束功率beam power电子束功率密度beam power density焦点focal spot焦距focal length工作距离work distance电子束焊机electron beam welding machine高真空电子束焊机full vacuum electron beam welder低真空电子束焊机partial vacuum electron beam welder 非真空电子束焊机nonvacuum electron beam welder真空度vacuum电子枪electron gun二极电子枪diode gun三极电子枪triode gun偏压电极bias electrode电磁透镜electromagnetic lens电子束偏转线圈electron beam deflection coils导流系数perveance钉尖spiking激光焊laser welding/ laser beam welding连续激光焊continuous laser welding脉冲激光焊impulsed laser welding激光焊机laser welding equipment气体激光器gas laser固体激光器solid laser焦斑直径focussed diameter of the beam离焦量clearance between focal point and (plate) surface 焊缝深宽比weld seam depth-to-width ratio气焊gas welding氧乙炔焊oxy-acetylene welding氢氧焊oxy-hydrogen welding空气乙炔焊air-acetylene welding氧乙炔焊oxy-acetylene flame氢氧焰oxy-hydrogen flame氧煤气焰oxy-coal gas flame焊接火焰welding flame混合比mixing ratio混合气体可燃范围inflammable limit of the gaseous一次燃烧primary combustion二次燃烧secondary combustion燃烧速度combustion rate燃烧强度combustion intensity火焰热效率flame heating efficiency焰芯inner cone; flame cone内焰internal flame外焰flame envelope中性焰neutral flame氧化焰oxidizing flame碳化焰carburizing flame还原区reducing zone火焰稳定性flame stability回火flashback逆火backfire回烧flashback气体发生速度gasification speed焊炬torch; blow pipe等压式焊炬balanced pressure torch射吸式焊炬injector torch氧乙炔焊炬oxy-acetylene torch焊割两用炬combined cutting and welding torch 混合室mixing chamber喷射器injector焊嘴welding nozzle; welding tip液氧气化器oxygen evaporator气瓶gas cylinder乙炔瓶acetylene cylinder阀罩cylinder cap气瓶阀cylinder valve汇流排cylinder manifold减压器pressure regulator; gas regulator单级减压器single stage regulator两级减压器two stage regulator回火防止器flashback arrestor干式回火防止器dry flashback arrestor水封式回火防止器water-closing type arrestor净化器purifier乙炔发生器acetylene generator低压乙炔发生器low pressure acetylene generator 热剂焊thermit welding (TW)热剂补焊thermit repair welding钢轨热剂焊thermit rail welding热剂thermit powder热剂钢水thermit steel热剂反应thermit reaction热剂溶渣thermit slag热剂铸模thermit mold; mold for thermit weld热剂坩埚thermit crucible焊筋collar水下焊underwater welding水下气体保护电弧焊underwater gas shielded arc welding水下等离子弧焊underwater plasma arc welding温式水下焊wet method underwater welding干式水下焊dry method underwater welding局部干式水下焊local dry underwater welding水帘局部干式水下焊water curtain type dry underwater welding 遥控水下焊remote controlled underwater welding电弧空腔arc bubble电阻焊resistance welding (RW)点焊spot welding; resistance spot welding凸焊projection welding缝焊seam welding滚点焊roll-spot welding连续点焊stitch welding多点焊multiple spot welding手压点焊push welding; poke welding脉冲点焊pulsation spot welding; multiple-impulse welding双面点焊direct spot welding单面点焊indirect spot welding串联点焊series spot welding多点凸焊multiple projection welding频道进缝焊step-by-step seam welding压平缝焊mash seam welding串联缝焊series seam welding对接缝焊butt seam welding; foil-butt seam电阻对焊upset butt welding闪光对焊flash butt welding (FBW)储能焊stored energy welding电容储能点焊condenser discharge spot welding高频电阻焊high frequency resistance welding冲击电阻焊percussion welding胶接点焊spot weld-bonding; weld-bonding闪光flashing; flash过梁bridge; lintel顶锻upsetting; upset夹紧力clamping force顶锻力upsetting force; upset force。
焊接相关英汉词汇
焊接相关英汉词汇argon arc weld 氩弧焊butt weld 对接焊（缝）cluster weld 丛聚焊（缝）cold weld 冷焊（缝），冷压接fillet weld 角焊（缝）flash butt weld 闪光对接焊（缝）full fillet weld 满角焊（缝）groove weld 坡口焊（缝）mash seam weld 滚压焊seam weld 滚焊（缝）slot weld 切口焊（缝）spot weld 点焊（缝）tack (positioned) weld 定位【点位】焊（组焊前）weldability 可焊性，焊接性welder 焊工；焊机welding 焊接（法），焊接（的），焊缝atomic hydrogen weld 原子氢焊attachment weld 固定焊接bead weld 堆焊，狭的焊接braze weld 硬【钎】焊，铜焊built-up weld 堆焊down hand weld 俯【水平】焊接electric arc weld 电弧焊flat position weld （顶面）平【卧】焊flow weld 铸（浇）焊forehand weld 正手焊（法）forge weld 锻焊，锻接friction weld 摩擦焊gas shield weld 气体保护弧焊inert-gas metal-arc weld 焊丝惰性气体保护焊oxyacetylene weld 氧（乙炔）焊，气焊percussion weld 冲击焊plasma-arc weld 等离子弧焊repair weld 补焊roll weld 滚压焊scarf weld 斜面焊，两端搭接焊，嵌接焊shield weld 气体保护焊union arc weld 磁性焊剂二氧化碳保护焊unionmelt weld 埋弧（焊剂层下）自动焊weldment 焊接件，焊接装配bonding technology 焊接工艺fillet weld 角焊,填角焊seal welding. 密封焊接ring joint 环接, 围缘接合seal fitting 密封接头, 密封配件weld reinforcement 焊缝补强dimensional inspection 尺寸检验flange gasket 法兰垫片burn through 烧蚀girth weld 环形焊缝reinforcement of weld 加强焊缝weld joint 焊缝, 焊接接头circumferential joint 周圈接缝butt weld 对接焊缝arc welding 电弧焊filler rod 焊条shield gas 保护气体welding rod 焊条welding bead 焊道，熔敷焊道，焊珠electrode 电焊条longitudinal. 纵向的horizontal line 水平线welded joint 焊接缝焊接节点witness test 订货人在场的试验Alignment：对准,定位调整gas cutting. 气割arc cutting 电弧切割grind off 磨掉Leveling：校平Fixing：固定Console：控制台material certificate 材料合格证fabrication 加工,制造post weld heat treatment 焊后热处理flushing 冲洗，填缝arc gouging 电弧刨削machining 机械加工nut 螺母solvent 溶剂tack welding 点焊butt welding 对接焊reinforcing pad.补强垫,增强衬板flux 焊剂blind 挡板gusset plate 角撑板, 加固板base material 基底材料flow sheet 流程图witnessed inspections 现场检测drain 排水管identification mark 识别标志silicone paint 硅树脂油漆fabrication drawing 制造图纸,制作图WPS Works Process Specification 典型工艺规程caulking metal 填隙合金[金属](材料) weld bead 焊缝weld mark 焊痕bonding wire 接合线, 焊线埋弧焊Submerged-arc Welding 电阻焊Resistance Welding 滚焊Seam welding throat thickness 焊缝厚度weldability 可焊性，焊接性Weldable steel 焊接钢Weldability of metal 金属可焊性Weldability test 可焊性试验Weld all around 围焊Weldable copper 可焊复合铜板Weld assembly 焊接件Weld bond 熔合线，焊口Weld cap 焊冒Weld collar 加强焊缝焊瘤Weld crack 焊接裂缝Weld crater 熔池Weld crosswise 交叉焊接Weld decay 焊缝腐蚀，焊接接头晶间Weld defect 焊接缺陷Weld deposit 堆焊，焊缝熔敷Welded all round 沿周边焊接的Welded armor 焊接甲板Welded body 焊接车身Welded bridge 焊接桥Welded bond 焊接轨隙连接器，焊接导接线Welded cathode 焊接阴极Welded chain 焊接链Welded connection 焊接合，焊接头Welded construction 焊接结构Welded－contract rectifier 焊接整流器Welded corner joint 角焊接weldability 可焊性，焊接性Weldable steel 焊接钢Weldability of metal 金属可焊性Weldability test 可焊性试验Weld all around 围焊Weldable copper 可焊复合铜板Weld assembly 焊接件Weld bond 熔合线，焊口Weld cap 焊冒Weld collar 加强焊缝焊瘤Weld crack 焊接裂缝Weld crater 熔池Weld crosswise 交叉焊接Weld decay 焊缝腐蚀，焊接接头晶间Weld defect 焊接缺陷Weld deposit 堆焊，焊缝熔敷Welded all round 沿周边焊接的Welded armor 焊接甲板Welded body 焊接车身Welded bridge 焊接桥Welded bond 焊接轨隙连接器，焊接导接线Welded cathode 焊接阴极Welded chain 焊接链Welded connection 焊接合，焊接头Welded construction 焊接结构Welded－contract rectifier 焊接整流器Welded corner joint 角焊接Welded eye 焊眼Welded fissure 焊接裂缝Welded fitting 焊接式管接头Welded flange 焊接翼缘Welded frame 焊接车架，焊接框架Welded frog 焊接辙差Weld edgewise 沿边焊接Welded metal 焊接金属Welded pipe 焊接管Welded module 焊接微型组件Welded on head 焊制封头，焊制端盖Welded plate 焊合板Welded seam 焊缝Welded shell course 焊接锅炉筒Welded shell ring焊接锅炉筒Welded splice 焊接接头Welded steel 焊接钢Welded steel fabric 焊接钢筋网Welded steel forging 熔焊钢锻件Welded steel pipe 焊接钢管Welded steel pipe pile 焊接钢管桩Welded structural shape 焊接结构型钢Welded structural 焊接结构Welded truss 焊接桁架Welded tube 焊缝[接]管Welded turret 焊合转塔Welded wire fabric 焊接钢丝网Welder 焊机，焊工Welder construction 焊接结构Welder performance qualification test 焊工技术鉴定试验Welder’s gauntlets 电焊工的长手套Welder’s gloves 电焊工手套Welder’s goggles 焊工护目镜welder’s hand shield 焊工手持护目镜Welder’s head shield 焊工护目帽罩Welder’s health 焊工保健Welder’s helmet 焊工帽罩Welders spatter ease 焊接易飞溅液Welder with condenser 带电容弧焊机Welder with taps 抽头式焊机Weld flaw 焊接缺陷，焊接裂纹Weld flush 焊缝隆起Weld flux 焊剂，焊药Weldforged 锻焊Weld gauge 焊缝量规Weld handle 焊把Weld holder 焊接架Welding 焊接法，熔接，定位焊接；粘结Welding agent 焊药Welding alloy 焊接合金Welding and cutting torch 焊割两用气焊枪Welding－and－forming mill 成型焊管机Welding apron 焊工的围裙Welding arc 焊弧Welding arc voltage 焊弧电压Welding assembly 焊接构件Welding base metal 焊条金属Welding beading 焊瘤Weldingbead length 焊缝长度Welding bell 碗模（焊管用的），拔管模，喇叭模Welding bench 焊接工作台Welding blew lamp 焊炬Welding blowpipe 气焊吹管Welding booth 焊接室Welding burner 焊炬喷嘴Welding by both sides 双面焊Welding by forging 锻焊Welding by one side 单面焊Welding cable 电焊电缆，电焊引线Welding characteristics 焊接特性Welding compound 焊【接】剂Welding conditions 焊接规范Welding connector 电缆夹头Welding contactor 电焊接触器Welding control 接触焊机断流器Welding crack 焊裂缝Welding current 焊接电流Welding cut bit 焊接工具Welding deformations 焊接变形Welding direction 焊接方向Welding dynamo 焊接发电机Welding electrode 电焊条，电焊电极Welding electrode hold 焊条夹Welding equipment 焊接设备Welding fixture 焊接夹具Welding flame 焊接火焰Welding flash 弧光灼伤Welding fluid 熔【焊】剂Welding flux 焊剂，焊药Welding force 阻焊加压；电极压力Welding from both sides 双面焊Welding from one side 单面焊Welding furnace 烧结炉Welding gauge 确定焊缝尺寸用样板Welding gang 焊工班，焊接组Welding generator电焊发动机Welding generator with differential excitation 差激电焊发动机Welding generator with split－Poles 裂极电焊发动机Welding glass 黑玻璃Welding gloves焊接手套Welding goggles 焊工护目镜Welding grade argon 焊接极氩，焊接用氩Welding grade gas 焊接级保护气体Welding ground 电焊地线Welding gun 焊枪，喷灯Welding gutter 焊管拉模Welding handle 焊条夹，电极夹钳Welding head 焊头，烙铁头，焊接机头Welding heat 焊热Welding heat input 焊接输入热量Welding helmet 焊工帽罩Welding holder 焊工握把Welding impulse 电焊脉冲Welding inspection 焊接检查Welding iron 烙铁Welding jig 焊接夹具Welding joint 焊接接头Welding lead 焊接引线Welding machine 焊机Welding manipulator 焊件支架Welding metal cracking 焊缝金属裂纹Welding method 焊接方法Welding motor generator 电动旋转式电焊机Welding neck （flange）对焊法兰Welding－on 焊合，镶焊，焊上Welding operation 焊接操作Welding operator 自动焊工Welding outfit 焊接配备Welding paste 焊接涂料Welding performance 焊接性能Welding pipe 焊接管Welding pistol 焊枪Welding point 焊接接头Welding pool 焊接熔池Welding portion 焊接部位，施焊部位Welding position 焊接部位Welding positioner 焊接胎架，可动焊接工作台Welding positioner roller 焊接定位滚轮Welding powder 焊粉Welding power lead 焊接用输电线Welding press 焊接压力机Welding pressure 焊接压力Welding procedure 焊接工艺，焊接程序Welding process 焊接法Welding quality 焊接质量Welding rectifier 电焊整流器Welding regulator 焊接[电流]调节器Welding research council 焊接研究委员会Welding residual stress 焊接残余应力Welding resistor 焊接电阻器Welding rod 焊条Welding rod coating 焊条上的焊药Welding rod core 焊条芯Welding rod extrusion press 焊条自动涂抹机，焊条压涂机Welding rolls 焊条辊Welding rules 焊接规则Welding screen 电焊遮光罩Welding seam 焊缝Welding sequence 焊接程序Welding set 焊接装置，电焊机组Welding set with a surge injector 脉冲稳弧焊接装置Welding set with DC suppression capacitors 电容抑制直流成分的焊接设备Welding set with H.F. ionizer 带高频电离的焊接装置Welding shop 焊接车间Welding slag 焊渣Welding sleeves [焊接用]套轴Welding socket 焊接管套（管接头）Welding source 焊接电源Welding spats 焊接用护脚Welding spatter 焊渣Welding steel 焊接钢Welding stick 焊丝，焊条Welding strain 焊接应变Welding stress 焊接应力Welding symbol 焊接符号，焊接代号Welding table 焊接工作台Welding temperature 焊接温度Welding thermit [铝]热剂（焊接用）welding tip 焊嘴，焊接吹管火口Welding tongs 焊钳Welding tool 焊接工具Welding torch 焊接喷灯，焊接吹管，焊炬Welding torch pipe 焊枪管Welding transformer 电焊变压器Welding tub 焊接熔池Welding wheel 盘状电极Welding wire 焊条，焊丝Welding－wire reel 焊丝卷圈Welding with backing 垫板焊Welding with flux backing 焊剂垫焊Welding with pressure 压焊Welding with weaving 横向摆动焊接Welding work 焊工工作Welding－in nozzle 焊入式喷嘴Welding interface 焊接界面Weld jig 焊接夹具Weld joint 焊缝，焊接接头Weld junction 熔合线，焊口Welding layer 焊接层Weld length 焊缝长度Weldless 无焊缝的，无缝的Weldless connection 非焊接式接头Weldless drawn pipe 拉制无缝管Weldless fitting 非焊接式接头Weldless pipe 无缝管Weldless steel tube 无[焊]缝钢管Weld line 焊接线Weld machined flush 削平补强的焊缝Weld mark 焊接痕，焊波Weldment 焊接件，焊接装配Weld mesh crate 焊接网格Weld metal 焊接金属，焊缝金属Weld metal cracking 焊缝裂纹Weld metal zone 焊接金属熔化区Weld on bottom 底焊Weldor 焊工Weld pass 焊接通道Weld penetration 焊穿，焊透深度，熔深Weld period 焊接时间Weld preparation 焊缝坡口加工Weld puddle 熔池Weld reinforcement 焊缝补强Weld ripple 焊缝波纹Weld rod 焊条Weld rotation 焊缝转角Weld seam 焊缝Weld slope 焊缝倾角Weld strain 焊接应变Weld strength 焊接强度，焊缝强度Weld surface 焊缝表面Weld time [接触焊的]通电时间Weld trimmer 焊缝清理机Weld up 焊补，焊封Weld wire 包钢铜丝Weldwood 胶合板Weld zone 焊接区Lack of fusion 未熔合Sharp edge 锐边Serrated edge 锯齿形边Torch cut 火焰切割Sawn 锯Air tight 气密性。
常用焊接术语中英文对照
常用焊接术语中英文对照焊接Welding10。
1 焊接种类Varieties of Welding电弧焊arc welding电熔焊electric fusion welding (EFW）气熔焊fusion gas welding (FGW）电阻焊electric resistance welding （ERW)有保护的金属电弧焊shielded metal arc welding （SMAW）手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW）自动埋弧焊automatic submerged arc welding金属极隋性气体保护电弧焊gas metal arc weiding （GMAW）氩弧焊argon-arc welding,气体保护电弧焊gas-shielded arc welding气焊gas welding；flame welding等离子焊plasma welding硬钎焊braze welding电渣焊electroslag welding爆炸焊explosive welding10。
2 焊接形式Type of Welding角焊fillet welding间断焊intermittent welding点焊spot welding对焊butt welding搭焊lap welding塞焊plug welding珠焊bead welding槽焊slot welding堆焊build up welding垫板焊backing weld坡口grooveV形坡口V groove单面U形坡口single U grooveK形坡口double bevel grooveX形坡口double V groove双面U形坡口double U grooveU—V组合坡口combination U and V groove根部间隙root gap焊接符号symbol of weld错边量alignment tolerance10。
焊接常用词语英汉对照共101页word资料
焊接常用词语英汉对照actual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝中心线; 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机electric-weld pipe mill电焊管机emporary weld临时点定焊缝excess weld metal焊缝补强金属; 补强; 补强焊料; 补强金属excess weld metal(焊缝的)余高explosive weld爆炸焊接face of weld焊缝表面; 焊接面fibrous weld纤维状焊缝field weld现场焊接filler weld填角焊缝fillet weld角焊缝; 填角焊; 贴角焊fillet weld in normal shear (搭接接头的)正面角焊缝fillet weld in parallel shear侧面角焊缝; 侧面填角焊fillet weld in the flat position角接平焊; 水平角焊缝fillet weld in the horizontal position横向角焊缝fillet weld size焊角尺寸; 填角焊缝尺寸flame weld火焰焊接flange weld卷边焊缝; 卷边焊缝flange-to-web weld卷边焊缝; 卷边焊缝flanged butt weld弯边对接焊flanged edge weld卷边焊; 卷边焊flash butt weld闪光焊flash weld闪速对焊flat faced fillet weld平顶角焊缝焊接flat fillet weld平角焊ing of fillet weld角焊缝平焊; 船形角焊flush fillet weld平角焊flush weld削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld锻焊焊缝forged weld (焊后锻压的)锻压焊缝form factor of the weld焊缝成形系数formation of weld焊缝成形front fillet weld正侧面填角焊缝; 正面填角焊front(al) fillet weld正面角焊缝full fillet weld满角焊缝; 全角焊full penetration butt weld满对接焊full weld满焊full-fillet weld满角焊full-sized weld全尺寸焊缝full-strength weld (与母材等强)等强焊缝gap weld特殊点焊; 双极单点焊gas-pressure weld气压焊girth weld环形焊缝gravity weld倚焊groove weld坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint有坡口焊接接头hammer weld锻焊hand weld手焊焊缝height of reinforcement of weld加强焊缝高度helical-weld pipe螺旋焊管high performance weld flux高性能焊剂horizontal fillet weld横向角缝焊接horizontal weld横向焊缝horizontal-vertical fillet weld横向垂直角焊缝hot weld encapsulation热焊封袋hydraulic automatic weld液压自动焊接hydraulic weld process液压焊接法inclined weld斜焊inconel weld单面焊缝incorrect weld profile焊缝形状不对incorrect weld size焊缝尺寸不对induction weld mill感应焊管机inside corner weld内角焊接inside fillet weld内角焊接inside weld内焊缝insufficient or excess reinforcement of weld加强焊缝不足或过量intermittent fillet weld间断角缝焊接; 断续角焊缝intermittent weld断续焊; 断续焊缝jam weld对接焊; 对头焊接lap fillet weld搭接角焊缝laser (beam) weld (ing)激光焊lateral weld侧焊; 侧面焊缝leg of a fillet weld角焊缝; 角焊缝焊脚leg of fillet weld圆角焊肉厚length of weld焊缝长度light closing weld轻连续焊接light fillet weld轻型填角焊; 小填角焊light weld轻焊缝Lincoln weld埋弧自动焊longitudinal fillet weld纵向角焊longitudinal weld纵向焊缝longitudinal weld (焊接用语)纵缝loose weld脱焊main weld主焊缝mash seam weld压薄缝焊; 滚压焊mash weld点焊; 点压焊melt thru weld熔透焊缝melt-through weld透溶焊melten weld pool焊接熔池melting through weld熔透焊缝miter weld平顶角焊缝; 斜接角焊缝molten weld metal熔融焊接金属mulitple impulse weld多脉冲焊缝multilayer weld多层焊缝multipass weld多道焊缝multiple arc weld多弧焊缝multiple-electrode submerged arc weld多电极埋弧焊multiple-pass weld多道焊缝; 多路焊接multirun weld多道焊缝nonpressure thermit weld不加压热剂焊缝normal weld正常焊接oblique fillet weld斜交角焊缝; 斜角焊接one-pass weld单层焊缝open butt weld开口对接焊open weld留间隙焊缝; 空隙焊outside weld外焊缝over weld过焊overhead fillet weld仰焊角焊缝overhead weld仰焊oversize weld超尺寸焊缝oxygen weld氧气焊接parallel-arc weld并列弧焊patch weld补焊; 补孔焊缝Peltier's cross weld珀耳帖交叉焊接penetration weld熔透焊缝percussion weld冲击焊缝; 冲击焊接periphera weld环形焊缝pitch of weld焊缝接距; 焊线距plain butt weld无坡口对接焊; 平头对接焊缝plasma-arc weld等离子弧焊接plug weld塞焊焊缝point of weld焊接点point weld点焊poor weld劣质焊缝; 有缺陷的焊缝porous weld多孔焊缝; 疏松焊缝positioned weld平位焊缝; 暂焊post weld annealed (PWA)焊后退火poured weld铸焊焊缝powder weld process粉末焊接法practice weld试验焊缝pressure weld压焊pressure-controlled weld压力控制焊接pressure-tight weld气密焊; 密封焊道principal weld主要焊缝profile of fillet weld填角焊缝轮廓progress of weld焊向projection weld凸焊; 凸焊焊缝projection weld machine凸点电阻焊机pulsating weld脉冲接触焊push weld挤焊quilting weld钉焊reinforced butt weld补强的对接焊缝; 补强式对接焊缝reinforced weld加强焊接reinforcement of weld焊缝加厚; 补强金属; 加强焊缝resistance weld mill电阻焊管机resistance weld pipe电阻焊管resonance butt weld谐振式对接焊restarting a weld再引弧ripple weld鳞状焊缝rivet weld电铆; 电铆焊缝root face of weld焊缝根部钝边root gap of weld焊缝根部间隙root of weld焊缝根部; 焊根root opening of weld焊缝根部间隙root radius of weld焊缝坡口根部半径sagged weld下垂焊缝scarf weld楔口焊接seal weld填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝sealing weld封焊seam weld滚焊semi-automatic arc weld半自动电弧焊sequence weld timer序列焊接时间调节器shallow weld浅焊shop weld工厂焊接shot weld点焊shoulder of weld焊缝根部钝边side fillet weld侧面角焊缝; 侧面填角焊缝; 侧面贴角焊side lap weld侧边搭接焊; 弯边搭焊缝side weld侧焊缝; 边焊single lap weld单搭接焊single strap butt weld单面盖板对接焊single-bevel groove weld单斜角槽焊single-fillet weld单边角接焊缝single-pass weld单道焊site weld现场焊接; 安装焊; 安装焊接size of a fillet weld焊角尺寸size of weld焊件的大小; 焊区尺寸skew weld斜焊skin weld表面焊接sleeve weld套筒焊接slip-weld hanger卡瓦焊接套管挂slot weld槽塞焊; 长孔焊; 开槽搭焊缝; 切口焊缝ing slotted weld槽焊slotted lap weld切口搭接焊smooth fillet weld平填角焊缝socket weld ends承插焊接端soft-weld铜镍焊条合金solvent weld溶剂焊接space of intermittent weld断续焊缝间距; 断续焊间距spiral weld螺旋形焊缝spiral weld-pipe mill螺旋焊管机spot weld焊点spot weld bonding胶结点焊spot weld nugget点焊熔核spreading weld宽缝焊接; 加宽的焊缝square butt weld平头对接焊缝square groove weld无坡口槽焊staggered intermittent fillet weld (ing)交错断续角焊staggered intermittent weld交错断续焊缝; 交错间断焊staggered plug weld交错塞焊standard reinforced fillet weld标准加强角焊缝stick-out weld未熔合点焊接头stitch-and-seam weld点线焊straight butt weld无坡口对接接头strapped weld搭板对接焊缝strength weld受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld强固焊缝surface of weld焊缝表面surface weld表面焊缝surface weld metal buildup表面焊缝金属的形成synthetic apparatus for weld thermal cycle焊接热循环模拟装置T weld丁字接头焊缝T-filled weld丁字形角焊T-fillet weld丁字接头角焊缝tack weld定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding)定位焊tandem arc weld前后弧焊temporary weld临时点固焊缝tension weld受拉焊缝test weld试焊throat depth (thickness) of fillet weld角焊缝厚度throat of fillet weld凹角焊喉; 填角焊缝喉长throat of weld凹角焊喉tight weld密封焊接; 致密焊缝tight-strong weld密实强固焊缝toe of the weld焊缝边界toe of weld焊趾toe weld趾部焊缝torch weld气焊焊缝total amount of weld fumes焊接发尘量transverse fillet weld横向角焊缝; 正面角焊transverse weld横向焊缝trial weld试验焊接undercut weld底切焊接undressed weld (增加焊缝)未加工焊缝unequal fillet weld焊脚不等的角焊缝unfitness of butt weld焊缝对口错边量union-melt weld埋弧焊unload weld非承载焊缝unspaced butted weld无间隙对接焊缝upgrading of boiler weld锅炉焊缝加强vertical fillet weld立焊角焊缝vertical weld立焊weak weld不强固焊缝weaving weld横向摆动焊缝weld焊; 焊接的; 补焊weld all around围焊weld appearance焊缝外观weld assembly焊接组件weld back-up焊缝背垫weld backing焊缝衬垫weld bead焊缝; 熔敷焊道weld bead height焊缝高度weld beading焊瘤weld bond熔合线weld bridge seam搭桥焊缝; 桥接焊缝weld cap焊帽weld center line焊缝中心线weld collar加强焊缝焊瘤weld crack焊接裂纹weld crater熔池weld crosswise交叉焊接weld decay焊缝腐蚀; 焊接接头晶间腐蚀; 焊接侵蚀; 焊接区晶间腐蚀weld decay (焊接后)敏化区腐蚀weld defect焊接缺陷weld delay time焊接延迟时间weld deposit堆焊weld deposits cleaning焊接熔敷金属清理weld edge焊缝边缘; 焊缝表面边缘weld edgewise沿边焊接weld flange connection焊接法兰连接weld flash焊瘤weld flaw焊接缺陷weld flush焊缝隆起weld fumes焊接烟尘weld gage焊缝检查规; 焊缝卡规weld gauge焊缝量规weld heat input焊接热输入; 焊接线能量weld holder焊接夹持架; 焊接架weld inspection焊缝质量检验; 焊接检查weld interface焊缝界面; 焊接界面weld interval焊接时间weld is accepted焊缝合格weld jig焊接夹具weld joint焊缝weld junction熔焊线; 熔合线weld layer焊接层weld length焊缝长度weld line焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush削平补强的焊缝weld mark焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate焊接网格weld metal焊缝金属; 焊接金属weld metal buildup surface金属堆焊表面weld metal composition焊接金属组成weld metal cracking焊缝裂纹weld metal zone焊缝金属区; 焊接金属熔化区weld nugget焊点熔核weld on bottom底焊weld overlap重叠区weld pass焊接通道weld penetration焊缝熔深; 焊透深度weld period焊接时间weld pitch焊缝距weld porosity焊缝气孔weld preheating焊前预热weld preparation焊缝坡口加工weld puddle熔池weld reinforcement焊缝补强; 焊缝加强; 焊接补强weld repairs焊接修补weld ripple焊缝波纹weld root焊件剖口; 焊接根weld root opening gap焊缝根部间隙weld root reinforcement焊缝反面加强weld rotation焊缝转角weld seam pipe焊缝管weld shape焊缝形状weld shielding焊接区保护; 焊接熔池保护weld slope焊缝倾角weld spacing焊点距; 焊缝间距weld strain焊接应变weld strength焊接强度weld surface焊缝表面weld swell焊缝隆起weld thermal cycle焊接热循环weld thickness焊缝厚度weld time焊接时间; 焊接通电时间; 接触焊通电时间weld toxic gases焊接有害气体weld trimmer焊缝清理机weld up焊补weld wheel conditioner焊轮调节器weld width焊缝宽度weld wire包铜钢丝weld zone焊缝区; 焊接区weld-form factor焊缝形状系数weld-fusion line焊缝熔合线weld-in nozzle焊入式喷嘴weld-interval timer焊接间隔记时器weld-shrunk cylinder包扎式圆筒weld-shrunk multilayered cylinder包扎式多层圆筒; 多层包扎式圆筒weld-throat thickness depth焊缝厚度window type restraint weld cracking test窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld焊缝表面AC & D. C. arc welding machine交直流弧焊机AC arc welding交流电弧焊AC gas metal-arc welding process交流熔化极气保护焊AC gas tungsten arc welding交流钨极气保护焊AC welding set交流焊机; 交流焊接变压器AC-dc welding machine交直流两用焊机acetylene welding气焊; 乙炔焊; 乙炔焊接acetylene welding torch乙炔焊炬; 乙炔接焊吹管air-acetylene welding空气-乙炔焊接all-position welding全位置焊接alloy steel gas welding rod合金钢气焊条alternating current arc welding交流电弧焊alternating current welding machine交流电焊机aluminium alloy arc welding electrode铝合金焊条aluminothermic welding铝热焊; 铸焊angle backwards welding后倾焊angle butt welding斜口对接焊angle forwards welding前倾焊annealing welding wave退火焊波antogenous welding氧炔焊apparatus for butt welding平接压焊夹具arc braze welding电弧钎焊arc flash welding电弧闪光焊arc spot welding电铆焊arc stud welding柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding弧压反馈电弧焊arc welding电弧焊; 电弧焊接; 弧焊arc welding electrode电弧焊条arc welding generator电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation自激弧焊发电机; 他激电焊发电机arc welding generator with self-excitation自激电焊发电机arc welding machine弧焊机; 电焊机; 电弧焊机arc welding mask电弧焊遮罩arc welding process电弧焊接工艺过程arc welding rectifier弧焊整流器arc welding robot弧焊机器人arc welding set电弧焊机组arc welding transformer弧焊变压器arc-welding electrode电弧焊用焊条arc-welding plant电焊厂arcogen welding电弧氧乙炔焊argon (shielded) arc welding氩弧焊接argon tungsten-arc welding钨极氩弧焊argon-arc welding氩弧焊argonaut welding自动氩弧焊atomic H welding氢原子焊atomic hydrogen welding原子氢焊atomic-hydrogen welding原子氢焊接austenite welding不锈钢焊接autogenous pressure welding自动压合热焊autogenous welding气焊automatic arc welding head自动电弧焊接机头automatic arc welding machine自动电焊机; 自动弧焊机automatic drying line for welding electrode电焊条自动烘焙线automatic slag pool welding自动电渣焊automatic spot welding自动点焊automatic submerged arc welding自动埋弧焊automatic submerged slag welding of rail钢轨automatic submerged-arc welding machine埋弧自动焊机automatic transverse welding横向自动焊automatic welding自动焊; 自动焊接automatic welding head自动焊头automatic welding machine自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process自动焊接工艺规程automation of welding焊接自动化back hand welding后退焊; 反手焊接back step welding反手焊接back ward welding反手焊接back welding底焊; 退焊法back-step welding分段退焊法backhand welding逆向焊; 右焊法; 后焊法; 向后焊backing welding打底焊backstep welding分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊backstep welding sequence分段退焊次序backward welding后倾焊; 后退焊; 向右焊balanced welding对称焊bare welding rod光焊条bare wire arc welding光焊丝电弧焊bead welding窄焊道焊接bench arc welding machine台式弧焊机bevel welding斜角焊blacksmith welding锻工焊接; 锻焊block sequence welding分段多层焊; 分段连续焊接block welding块焊接block welding sequence分段多层焊body welding machine罐身焊接机both sides welding双面焊接brass welding rod黄铜焊条braze welding钎焊; 钎焊接; 钎接; 铜焊braze-welding钎接焊bridge spot welding带接合板点焊; 单面衬垫点焊; 单面搭板点焊bridge welding桥接焊; 盖板焊brize welding硬焊build (built) up welding堆焊build-up welding堆焊building-up by welding堆焊butt resistance welding电阻对焊; 对接电阻焊butt seam welding对接滚焊butt seam welding machine对接缝焊机butt welding对接焊; 平对焊butt welding machine对接焊机butt welding process对接焊法butt-welding对接焊butt-welding machine对焊机capability of welding vertically upwards直上焊接能力capacitor-discharge welding电容放电焊接carbon arc welding碳弧焊; 碳极弧焊carbon in materials for welding焊接用材料中的碳carbon-dioxide arc welding二氧化碳保护焊carriage of automatic welding machine自动焊机走架cascade welding阶梯式焊; 山形多层焊cascade welding sequence串级叠置法cast welding铸焊cement-welding金属陶瓷焊接centralized installation of welding machine多站焊接chain intermittent fillet welding并列断续角焊缝; 链式断续角焊chemical welding化学焊circular seam welding环缝对接焊circular seam-welding machine环形滚焊机cleaning before welding焊接前的清理cleaning of welding deposits焊接沉积的清理closed butt gas pressure welding闭式加压气焊cold welding冷焊; 冷压焊cold-pressure welding冷压焊combined cutting and welding torch焊割两用炬combined cutting and-welding blow-pipe焊割两用炬combined thermit welding加压铸焊complete penetraction and fusion in welding全焊透condenser (discharge) spot-welding machine电容器放电点焊机condenser discharge spot welding电容储能点焊; 电容贮能点焊constant current welding machine恒流电焊机constant energy welding machine恒功率电焊机constant voltage welding machine恒压电焊机constant-current arc welding power source垂降特性弧焊电源constant-current welding source恒流式焊接电源constant-power welding source恒功率式焊接电源constant-pressure pressure welding恒压压力焊constant-temperature pressure welding恒温压力焊constant-voltage welding machine恒电压焊机constant-voltage welding source恒压式焊接电源; 平特性焊接电源consumable electrode welding熔化极电弧焊consumable guide electroslag welding自耗定向电渣焊contact welding接触焊continuous feed welding连续送丝电弧焊continuous welding连续焊; 连续焊接contour welding绕焊controlled arc welding可控电弧焊接controlled atmosohere arc welding充气室电弧焊controlled atmospere arc welding充气式电弧焊controlled tungsten-arc welding自动控制弧长的钨极电弧焊controlled-transfer welding可控过渡电弧焊convex fillet welding凸面角焊缝copper arc welding electrode铜焊条copper welding rod铜焊条copper-alloy arc welding electrode铜合金焊条copper-aluminium welding rod铜铝焊条copper-nickel welding rod铜镍焊条copper-silicon welding rod铜硅焊条copper-tin welding rod铜锡焊条copper-zinc welding rod铜锌焊条core welding-wire焊芯core wire for welding rod焊条芯线corrosion due to welding焊接腐蚀cosmetic welding盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machine二氧化碳弧焊机cracking test for automatic welding自动焊抗裂试验crankshaft flashbutt welding曲轴电阻弧花压焊cross welding横向焊缝cyc-arc welding圆环电弧焊deck welding重力焊deep fillet welding深角焊deep penetration welding深熔焊deep penetration welding electrode深熔焊条deep welding深焊die welding模焊; 冲模堆焊diesel engine driven DC arc welding machine柴油机驱动直流弧焊机differential-excited welding generator差激电焊发电机diffusion welding扩散焊接direct spot welding双面点焊direct welding双面点焊direction of welding焊接方位; 焊接方向discontinuous welding断续焊dot welding点焊double carbon-arc welding间接碳弧焊double side welding双面焊接down-hand welding俯焊downhand welding平焊downward welding in the inclined position下坡焊downward welding in the vertical position向下立焊dual-arc welding双弧焊edge seam welding端面接头滚焊edge welding边缘焊接edgewise welding沿边焊接electric and pressure welding电压力焊接electric arc spot welding电弧点焊electric arc welding generators电弧焊接发电机electric arc welding machine电弧焊机electric butt welding电阻接触焊electric resistance welding电阻焊接; 热电阻焊electric slag welding电渣焊electric spot welding电点焊electric welding电焊electric welding cast copper solder铸铜电焊条electric welding equipment电焊设备electric welding generator电焊发电机electric welding hammer电焊锤electric welding machine电焊机electric welding plant电焊厂electric welding pliers电焊钳electric welding rod电焊条electric welding strip电焊片electric-arc welding电弧焊electric-resistance seam-welding电阻缝焊electric-resistance seam-welding machine电阻缝焊机electrical arc welding电弧焊接electrical resistance welding tube电阻焊接管electrically heated welding torch电热焊枪electro-beam welding电子束焊接electro-gas (enclosed) welding气电立焊electro-slag welding电磁渣焊; 电渣焊electro-slag welding with plate electrode板极电渣焊electro-welding电焊electrode for arc welding电焊条; 电弧焊条electrode for vertical down welding向下立焊条electrode of vertical down welding立向下焊条electrode welding电弧焊electrogas welding气电焊; 电气焊electromagnetic percussive welding电磁冲击焊electromagnetic stored energy welding电磁储能焊electron beam welding电子束焊; 电子束焊接electron beam welding machine电子束焊接机electron-beam welding电子束焊接electron-beam welding machine电子束焊机electron-bombardment welding真空电子束焊electrons leaves welding电子束焊接electropercussive welding电冲击焊; 冲击焊; 储能焊electroslag welding电渣焊; 电阻焊electroslag welding machine电渣焊机electroslag welding with consumable nozzle熔嘴电渣焊electroslag welding with wire electrode丝极电渣焊electrostatic (percussive) welding电能储能焊接electrostatic percussing welding静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding静电冲击焊; 静电冲击焊enclosed welding强制成形焊接energy storage welding贮能焊; 储能焊; 脉冲焊接erecting welding装配焊接erection welding安装焊接eutectic welding低温焊exothermic welding铝热焊expanding or welding of tube with tubesheet管子与管板的胀接或焊接explosive welding (EW)爆炸焊eyelet welding孔焊; 小孔熔焊faster welding快速焊接feed rate of welding wire焊丝送进速度field of welding temperature焊接温度场field welding现场焊接; 工地焊接Filler arc welding菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position船形角焊fillet welding in the flat position船形焊fillet welding in the horizontal position横角焊fillet welding in the vertical position立角焊fine welding精密焊接fine wire welding细丝焊fire cracker welding躺焊fire welding锻焊; 锻接fixed welding machine固定式焊机fixed-position welding定位焊接flame welding熔气焊flare welding喇叭形坡口焊接flash butt welding闪光对焊; 闪光对接焊wire welding焊网flash welding闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊flash-butt welding电阻闪光焊接flashover welding闪光焊flat position welding平焊; 顶面平卧焊flat position welding of fillet weld角焊缝平焊; 船形角焊flat welding平卧焊flexible welding rod软焊条flexible wire for electric welding电焊软线flow welding流注焊接; 浇焊fluid welding流焊flux-cored welding包芯焊条焊接fly-wheel type friction welding贮能摩擦焊; 储能摩擦焊flywheel friction welding惯性摩擦焊forehand welding向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding锻焊; 锻接焊forward welding正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊friction welding摩擦焊; 摩擦焊接friction welding machine摩擦焊接机frontal fillet welding正面角焊full automatic welding全自动焊full-automatic arc welding全自动电弧焊full-fillet welding满角焊full-fusion thermit welding热剂铸焊full-fusion welding全熔合焊full-length welding满焊fusion pressure welding熔化压接fusion thermit welding热剂熔焊; 熔化铝热焊fusion type plasma arc welding熔透型等离子弧焊fusion type welding熔透型焊接法fusion welding熔焊接fusion welding metal熔焊金属gas carbon-arc welding气保护碳弧焊gas electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊gas metal-arc welding气保护金属极电弧焊gas shield welding气体保护弧焊gas shielded arc welding气体保护电弧焊; 气体保护焊gas shielded arc welding machine气保护弧焊机gas shielded arc-welding machine气体保护弧焊机gas shielded magnetic flux arc welding磁性焊剂气体保护电弧焊gas shielded metal-arc welding气体保护金属弧焊gas shielded welding气体保护焊gas torch welding气炬焊gas tungsten arc welding气体保护钨极电弧焊gas tungsten-arc welding气保护钨极电弧焊gas tungstun arc welding钨极气体保护焊gas welding气焊; 乙炔焊gas welding device气焊设备gas welding equipment气焊设备gas welding machine气焊机gas welding outfit气焊机gas welding rod气焊焊丝gas welding rubber hose气焊橡胶管gas welding technique气焊工艺gas welding torch butt气焊进气硬管gas welding tube mill瓦斯焊接机gas welding work气焊工作gas-arc welding气电焊; 气体保护电弧焊gas-arc welding gun气电焊焊嘴gas-press welding气压焊gas-pressure welding machine气压焊接机gas-shielded stud welding气保护柱钉焊接girth welding环缝横向焊接gravity type arc welding重力焊gravity type welding倚焊gravity welding重力焊; 重力式电弧焊groove welding槽焊; 坡口焊; 开槽焊guided automatic welding导向自动焊接gun welding machine手提式点焊机; 点焊枪hafnium welding wire铪焊丝hammer welding锻焊; 锻接; 锤焊hammered resistance welding锤锻电阻焊; 电阻加热锻焊hand welding holdet手焊焊把hard-welding硬质合金熔焊headless bolt for welding焊接单头螺栓heat-welding adhesive热熔性胶粘剂heated-tool welding热烙铁焊接heavy welding大断面焊接heavy welding electrode粗电焊条heliarc welding氦电弧焊Heliarc welding氦弧焊法helium arc welding氦弧焊HF welding magnetic bar高频焊接磁棒hidden arc welding埋弧焊; 潜弧焊high current arc welding大电流弧焊high frequency AC welding machine高频交流电焊机high frequency dielectric welding高频介电焊high frequency induction welding高频感应焊high frequency welding高频焊接high grade energy welding高能焊high tensile electric welding rod高强焊条high-current plasma arc welding大电流等离子弧焊high-frequency induction welding高频感应焊接; 高频焊接high-frequency resistance welding高频接触焊high-frequency resistance welding (HFRW)高频电阻焊high-frequency welding高频电焊highspeed welding快速焊接horizontal fillet welding横角焊; 水平角焊horizontal position welding水平焊接; 横焊horizontal welding横焊; 水平焊horizontal-position welding水平位置焊接horizontal-rolledposition welding水平转动焊接; 滚动水平焊hot jet welding热风焊接hot press welding热压焊接hot pressure welding预热压力焊hot welding热焊hot wire welding热丝焊hot(-)gas welding热气焊接hot-gas welding热风焊接; 热空气焊接hot-pressure welding热压焊; 热压焊接hydrogen-welding氢焊impact spot welding冲击点焊法impregnated-tape metal-arc welding浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机impulse current seam welding machine脉冲电流缝焊机impulse current semiautomatic butt welding machine脉冲电流半自动对焊机impulse electromagnetic automatic welding machine电磁脉冲自动焊机impulse plasma welding machine脉冲等离子焊机impulse welding脉冲焊; 脉冲焊接impulsed spot welding脉冲点焊inclined position welding倾斜焊indirect (spot) welding单面点焊indirect welding单面点焊induction welding感应焊; 感应焊接; 感应熔焊inert gas arc spot welding惰性气体电弧点焊inert gas arc welding惰性气体电弧焊inert gas spot welding惰性气体保护电弧点焊inert gas welding惰性气体焊接法inert-gas (inert gas) arc welding惰性气体保护焊inertia welding惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding惯性焊接infrared welding红外线焊接intermediate current plasma arc welding中电流等离子弧焊intermittent fillet welding断续角焊intermittent point welding断续点焊intermittent welding断续焊International Institute of welding (IIW)国际焊接学会inverted welding仰焊joint welding搭焊jump welding丁字形焊keyhole-mode welding小孔型等离子弧焊; 穿透型焊接法lap fillet welding搭角焊; 搭接角焊lap resistance welding搭接电阻焊lap seam welding搭接缝焊; 搭接焊lap welding搭焊; 搭接焊laser welding激光焊接laser welding chamber激光焊接室laser welding head激光焊接头laser welding machine for orthodontics激光口腔矫形焊接机laser welding system激光焊接系统laser-beam welding machine激光焊接机laser-welding machine激光焊接器lead welding铅焊lefthand welding左焊法leftward welding左向焊法lever gun welding head杠杆式点焊钳light beam welding machine光束焊机light continuous welding轻连续焊接light gauge welding薄板焊接light ray welding光束焊接light welding轻焊接Linde welding林德钢管对焊法line welding直线焊缝焊接liquid metal welding浇注补焊longitudinal resistance seam welding纵向电阻缝焊longitudinal seam welding纵缝焊接; 纵向缝焊longitudinal welding纵缝焊接; 纵向焊接low carbon steel welding electrode低碳钢电焊条low carbon welding wires低碳焊接线材low idle voltage arc-welding power supply低空载电压的弧焊电源low temperature welding低温焊接low-alloy steel covered arc welding electrode低合金钢焊条low-current plasma arc welding小电流等离子弧焊low-hydrogen welding electrode低氢型电焊条low-temperature welding低温焊接lowest permissible temperature for welding焊接允许的最低温度machine for magnetic welding磁力焊接机machine welding机器焊接machine welding torch机械焊接吹管magnetic discharge welding电磁储能焊; 电磁焊magnetic flux arc welding磁性焊剂电弧焊magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊magnetic force welding machine磁力焊接机magnetic-force welding磁力焊接法manual arc welding手工电弧堆焊manual electic arc pile up welding手工电弧堆焊manual electric arc welding手工电弧堆焊manual electro-slag welding手工电渣焊manual gas welding手工气焊manual metal-arc welding手弧焊manual TIG welding手工钨极惰性气体保护焊manual welding手工焊接; 人工焊接manual welding machine手工焊机manually coating welding electrode手涂焊条mash seam welding滚压电阻缝焊mash stitch welding多针缝式焊接mask welding电焊眼罩match assemble welding装架焊接metal arc welding金属电弧焊metal buried welding埋渣焊metal inert gas arc welding (MIG)惰性气体金属电弧焊metal inert-gas arc welding金属极惰性气体保护焊metal inertia gas welding金属焊条惰性气体保护焊; 熔化极惰性气体保护焊metal rectifier welding set整流焊机metal-arc gas-shielded welding气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW)金属极气保护焊metal-arc welding金属极电弧焊micro resistance welding显微电阻焊micro-gap welding微间隙焊接micro-plasma arc welding微束等离子弧焊micro-welding微型焊接; 显微焊接microgap welding微隙间隙焊Miebach high efficiency flash welding machine米巴赫高效闪光对焊机mild steel arc welding electrode低碳钢焊条mild steel welding rod低碳钢焊丝miter welding斜接头焊接mixed gas arc welding混合气体保护电弧焊molten bath arc welding熔池电弧焊molten-bath arc welding熔池焊motor driven welding machine电动焊机; 电动机拖动式焊机motor-driven welding machine电动旋转式焊机motor-generator welding unit电动直流发电焊接设备multi-head automatic arc-welding machine多头自动电弧焊机multi-head automatic welding machine多头自动焊机multi-operator welding set多站电焊机multi-pass (multiple pass) welding多道焊multiarc welding多弧焊multihead automatic arc welding machine多弧自动电焊机multilayer welding多层焊multioperator welding generator多工位焊接发电机multioperator welding machine多站电焊机; 多站焊机multioperator welding set多站焊机multipass welding多道焊接multiple arc welding多弧焊multiple operator arc welding machine复式弧焊机multiple projection welding多点凸焊multiple resistance welding多点电阻焊接; 复式电阻焊multiple spot welding多点点焊multiple spot welding machine多点点焊机multiple-arc welding plant多弧焊接机multiple-electrode spot welding machine多极点焊机multiple-electrode welding多焊条焊接multiple-impulse welding多脉冲焊; 多脉冲接触焊multiple-operator welding-unit多重操作焊接单元multiple-spot welding多点焊multiple-wire multiple-power submerged-arc welding多丝埋弧焊multiple-wire submerged arc welding多丝埋弧焊multiplewire submerged-arc welding多丝埋弧焊nail head type welding钉头式焊接narrow gap one side welding窄间隙单面焊narrow gap one-side automatic welding窄间隙单面自动电弧焊。
焊接专业英汉词典
焊接专业英汉词典(1)2006-11-08 22:23:32 作者：jql来源：浏览次数：338 网友评论0条文字大小：【大】【中】【小】评分等级：0熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequence/deposition sequence焊缝倾角weld slope/inclination of weld axis焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
如水平固定管所进行的环缝焊接向下立焊vertical down welding/downward welding in the vertical posit ion向上立焊vertical up welding/upward welding in the vertical position倾斜焊inclined position welding上坡焊upward welding in the inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the downhand position/fillet welding in the flat position平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊foreward welding (英国)/ forehand welding (美国) 后倾焊backward welding(英国)/ backhand welding(美国) 分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding右焊法rightward welding/backhand welding挑弧焊whipping method自动焊automatic welding手工焊manual welding/hand welding车间焊接shop welding工地焊接site welding(英国)/ field welding (美国)拘束焊接restraint welding堆焊surfacing/building up/overlaying隔离层堆焊buttering端部周边焊boxing/end return返修焊rewelding补焊repair welding塞焊plug welding槽焊slot welding衬垫焊welding with backing焊剂垫焊welding with flux backing窄间隙焊narrow-gap welding强制成形焊enclosed welding脉冲电弧焊pulsed are welding电弧点焊arc spot welding螺柱焊stud welding热风焊hot gas welding高能焊high grade energy welding固态焊接solid-state welding单面焊双面成形one-side welding with back formation 焊接条件welding condition焊接工艺参数welding parameter极性polarity正接electrode negative/straight polarity反接electrode positive/reversed polarity运条方式manipulation of electrode焊接电流welding current焊接电流增加时间welding current upslope time焊接电流衰减时间welding current downslope time电流密度current density短路电流short circuit current脉冲电流pulse level/pulse current level脉冲电流幅值pulse current amplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy input热输入heat input预热preheat后热postheat焊后热处理posweld heat treatment/postheat treatment 预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element) 坡口groove坡口面groove face坡口面角度angle of bevel (英国)/ bevel angle (美国)坡口角度included angle(英国)/groove angle(美国)坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国)/root opening (美国)根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove with root face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U grooveVY形坡口single compound angle groove带钝边J形坡口single J groove带钝边双J形坡口double J groove单边V形坡口single bevel groove双V形坡口double V groove不对称双V形坡口asymmetric double V groove双单边V形坡口double bevel groove/K groove带垫板V形坡口V groove with backing/ single V groove with backing喇叭形坡口flare groove锁底坡口single bevel groove with backing locked坡形板边tapered edge焊缝weld接逢seam焊缝符号welding symbol焊缝金属weld metal填充金属filler metal熔敷金属deposited metal焊缝表面weld face/ face of weld焊缝背面back of weld焊缝轴线axis of weld焊缝尺寸size of weld焊缝宽度weld width/ width of weld焊缝长度weld length/ length of weld焊缝有效长度effective length of weld焊缝厚度throat depth/ throat thickness焊缝计算厚度theoretical throat焊缝实际厚度actual throat熔深penetration/ depth of penetration焊缝成形appearance of weld焊缝成形系数form factor of weld余高reinforcement/ excess weld metal背面余高root reinforcement削平焊缝flush weld/ weld machined flush对接焊缝butt weld角焊缝fillet焊脚leg/ fillet weld leg角焊缝断面形状profile of fillet weld平形角焊缝flat fillet凸形角焊缝convex fillet weld凹形角焊缝concave fillet weld角焊缝凹度concavity侧面角焊缝side fillet weld/ fillet weld in parallel shear 正面角焊缝front fillet weld/ fillet weld in normal shear 立角焊缝fillet weld in the vertical position横角焊缝fillet weld in the horizontal position平角焊缝fillet weld in the flat position斜角焊缝oblique fillet weld连续焊缝continuous weld断续焊缝intermittent weld连续角焊缝continuous fillet weld断续角焊缝intermittent fillet weld交错断续角焊缝staggered intermittent fillet weld并列断续角焊缝chain intermittent fillet weld端接焊缝edge weld卷边焊缝flanged edge weld塞焊焊缝plug weld纵向焊缝longitudinal weld横向焊缝transverse weld环行焊缝girth weld/ circumferential weld螺旋形焊缝spiral weld/ helical weld密封焊缝seal weld承载焊缝strength weld联系焊缝connective weld定位焊缝tack weld焊道bead/ run/ pass焊波ripple焊根weld root/ root of weld焊趾weld toe/ toe封底焊道sealing run (after making main weld)/ back weld打底焊道backing weld (before making main weld)/ back weld 根部焊道root pass/ root run填充焊道filling bead盖面焊道cosmetic bead/ cover pass回火焊道temper bead/ annealing bead熔透焊道penetration bead焊层layer接头形状joint geometry等强匹配接头equalmatching weld joint低强匹配接头undermatching weld joint超强匹配接头overmatching weld joint接头根部root of joint对接接头butt jointI形对接接头square butt jointV形对接接头single V butt jointU形对接接头single U butt jointJ形坡口接头single J butt joint双V形对接接头double V butt joint双单边V形对接接头double bevel butt joint/ K groove butt joint 带钝边U形对接接头double U butt joint带钝边J形坡口接头double J joint角接接头corner jointT形接头T joint斜T形接头inclined T joint十字接头cruciform joint/ cross-shaped joint三联接头joint among three members搭接接头lap joint套管接头muff joint/ sleeve joint双盖板接头double strapped joint盖板接头strapped joint端接接头edge joint卷边接头flanged edge joint锁底对接接头lock butt joint斜对接接头oblique butt joint混合接头mixed joint/ composite joint有间隙接头open joint焊接电弧welding arc电弧形态arc shape电弧物理行为arc physics behaviour引弧striking arc引弧电压striking voltage电弧气氛arc atmosphere阴极cathode热阴极hot cathode冷阴极cold cathode阴极斑点cathode spot阴极区cathode region阴极区电场强度intensity of the electric field in the cathode region 阴极压降cathode drop阳极anode阳极斑点anode spot斑点压力spot pressure阳极区anode region阳极区电场焊接专业英汉词典(2)2006-11-08 22:23:32 作者：jql来源：浏览次数：339 网友评论0条文字大小：【大】【中】【小】评分等级：0度intensity of the electric field in the anode region阳极压降anode drop弧柱arc column/ arc stream弧柱压降voltage drop in arc column弧柱电位梯度potential gradient in the arc column弧焰arc flame弧心arc core硬电弧forceful arc/ hard arc软电弧soft arc旋转电弧rotating arc脉冲电弧pulsed arc脉冲喷射电弧pulsed spray arc起皱现象puckering phenomena起皱电弧puckering arc起皱临界电流puckering critical current间接电弧indirect arc压缩电弧compressive arc磁控电弧magnetic controlling arc电弧力arc force电磁力electromagnectic force电磁收缩效应pinch effect电弧飘移wandering of arc电弧稳定性arc stability电弧静特性static characteristic of arc电弧动特性dynamic characteristic of arc最小电压原理principle of minimum voltage 电弧挺度arc stiffness电弧偏吹arc blow磁偏吹magnetic blow阴极清理作用cleaning action of the cathode 电弧自身调节arc self-regulation挖掘作用digging action极性效应polarity effect熔滴droplet熔滴比表面积specific surface of droplet熔滴过渡metal transfer过度频率transition frequency粗滴过渡globular transfer; drop transfer短路过渡short circuiting transfer喷射过渡spray transfer旋转喷射过渡rotating spray transfer脉冲喷射过渡pulsed spray transfer爆炸过渡explosive transfer渣壁过渡flux wall guided transfer熔池molten pool沸腾状熔池boiling molten pool弧坑crater熔渣slag渣系slag system渣系相图slag system diagram碱性渣basic slag酸性渣acid slag碱度basicity酸度acidity长渣long slag短渣short slag粘性熔渣viscous slag氧化物型熔渣oxide melting slag盐型熔渣salt melting slag盐-氧化物型熔渣salt-oxide melting slag熔渣流动性fluidity of the slag; slag fluidity 熔渣solidified slag多孔焊渣porous slag玻璃状焊渣vitreous slag自动脱落焊渣self-releasing slag脱渣性slag detachability焊接设备welding equipment; welding set焊机welding machine; welder电焊机electric welding machine; electric welder焊接电源welding power source焊接热循环weld thermal cycle焊接温度场field of weld temperature; weld temperature field 准稳定温度场quasi-stationary temperature field焊接热源welding heat source点热源point heat source线热源linear heat source面热源plane heat source瞬时集中热源instantaneous concentration heat source热效率thermal efficiency热能集中系数coefficient of heat flow concentration峰值温度peak temperature瞬时冷却速度momentary cooling rate冷却时间cooling time置换氧化substitutionary oxydation扩散氧化diffusible oxydation脱氧desoxydation先期脱氧precedent desoxydation扩散脱氧diffusible desoxydation沉淀脱氧precipitation desoxydation扩散氢diffusible hydrogen初始扩散氢initial diffusible hydrogen100℃残余扩散氢diffusible hydrogen remained at 100℃残余氢residual hydrogen去氢dehydrogenation去氢热处理heat treatment for dehydrogenation脱硫desulphurization脱磷dephosphorization渗合金alloying微量合金化microalloying一次结晶组织primary solidification structure二次结晶组织secondary solidification structure联生结晶epitaxial solidification焊缝结晶形态solidification mode in weld-bead结晶层状线ripple多边化边界polygonization boundary结晶平均线速度mean solidification rate针状铁素体acicular ferrite条状铁素体lath ferrite侧板条铁素体ferrite side-plate晶界欣素体grain boundary ferrite; polygonal ferrite; pro-entectoid fer rite粒状贝氏体granular bainite板条马氏体lath martensite过热组织overheated structure魏氏组织Widmannst?tten structureM-A组元martensite-austenite constituent焊件失效分析failure analysis of weldments冷裂判据criterion of cold cracking冷裂敏感系数cold cracking susceptibity coefficient脆性温度区间brittle temperature range氢脆hydrogen embrittlement层状偏析lamellar segregation愈合healing effect断口金相fractography断口fracture延性断口ductile fracture韧窝断口dimple fracture脆性断口brittle fracture解理断口cleavage fracture准解理断口quasi-cleavage fracture氢致准解理断口hydrogen-embrittlement induced 沿晶断口intergranular fracture穿晶断口transgranular fracture疲劳断口fatigue fracture滑移面断口glide plane fracture断口形貌fracture apperance断口试验fracture test宏观断口分析macrofractography放射区radical zone纤维区fibrous zone剪切唇区shear lip aone焊接性weldability使用焊接性service weldability工艺焊接性fabrication weldability冶金焊接性metallurgical weldability热焊接性thermal weldability母材base metal; parent metal焊接区weld zone焊态as-welded (AW)母材熔化区fusion zone半熔化区partial melting region未混合区unmixed zone熔合区bond area熔合线weld junction (英)；bond line (美)热影响区heat-affected zone (HAZ)过热区overheated zone粗晶区coarse grained region细晶区fine grained region过渡区transition zone硬化区hardened zone碳当量carbon equivalent铬当量chromium equivalent镍当量nickel equivalent舍夫勒组织图Schaeffler's diagram德龙组织图Delong’s diagram连续冷却转变图（CCT图）continuous cooling transformation 裂纹敏感性cracking sensibility焊接裂纹weld crack焊缝裂纹weld metal crack焊道裂纹bead crack弧坑裂纹crater crack热影响区裂纹heat-affected zone crack纵向裂纹longitudinal crack横向裂纹transverse crack微裂纹micro-crack; micro-fissure热裂纹hot crack凝固裂纹solidification crack晶间裂纹intercrystalline crack穿晶裂纹transcrystalline crack多边化裂纹polygonization crack液化裂纹liquation crack失延裂纹ductility-dip crack冷裂纹cold crack延迟裂纹delayed crack氢致裂纹hydrogen-induced crack焊道下裂纹underbead crack焊根裂纹root crack焊趾裂纹toe crack锯齿形裂纹chevron cracking消除应力处理裂纹stress relief annealing crack (SR crack)再热裂纹reheat crack焊缝晶间腐蚀weld intercryctalline corrosion刀状腐蚀knife line attack敏化区腐蚀weld decay层状撕裂lamellar tearing焊接性试验weldability裂纹试验cracking testIIW裂纹试验IIW cracking testY形坡口裂纹试验slit type cracking test分块形槽热裂纹试验segmented circular groove cracking testH形裂纹试验H-type cracking test鱼骨形裂纹试验fishbone cracking test指形裂纹试验finger (cracking) testT形裂纹试验Tee type cracking test环形槽裂纹试验circular-groove cracking test可调拘束裂纹试验varestraint testBWRA奥氏体钢裂纹试验BWRA cracking test for austenitie steel圆棒裂纹试验bar type cracking test; round bar cracking test里海裂纹试验Lehigh restraint cracking test圆形镶块裂纹试验circular-path cracking test十字接头裂纹试验cruciform cracking testZ向窗口拘束裂纹试验Z-direction window type restraint cracking test G-BOP焊缝金属裂纹试验G-BOP weld metal crack test巴特尔焊道下裂纹试验Battelle type underbead cracking testU形拉伸试验U-tension test缪雷克期热裂纹试验Murex hot cracking test菲斯柯裂纹试验FISCO (type) cracking testCTS裂纹试验controlled thermal severity拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test刚性拘束裂纹试验（RRC试验）rigid restraint cracking test插销试验implant testTigamajig 薄板焊接裂纹试验Tigamajing thin plate cracking test 焊道纵向弯曲试验longitudinal-bead test柯麦雷尔弯曲试验Kommerell bead bend test肯泽尔弯曲试验Kinzel test缺口弯曲试验notch bend test热朔性试验hot-ductility test热影响区冲击试验impact test of HAZ热影响区模拟试验synthetic heat-affected zone test最高硬度试验maximum hardness test落锤试验NRL (Naval Research Laboratory)测氢试验Hydrogen test焊接材料电极焊接材料welding consumables电极electrode熔化电极consumable electrode不熔化电极nonconsumable electrode钨电极tungsten electrode焊丝welding wire. Welding rod实心焊丝solid wire渡铜焊丝copper-plating welding wire自保护焊丝self-shielded welding wire药芯焊丝flux-cored wire复合焊丝combined wire堆焊焊丝surfacing welding rod填充焊丝filler wire焊条electrode/ covered electrode焊芯core wire药皮coating (of an electrode)/ covering (of an electrode)涂料coating flux/coating material造气剂gas forming constituents造渣剂slag forming constituents合金剂alloying constituent脱氧剂dioxidizer稳弧剂arc stabilizer粘接剂binder水玻璃water glass水玻璃模数modules of water glass酸性焊条acid electrode高钛型焊条high titania (type) electrode钛钙型焊条lime titania type electrode钛铁矿形焊条ilmenite type electrode氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode 高纤维素型焊条high cellulose (type) electrode石墨型焊条graphite type electrode碱性焊条basic electrode/ lime type covered electrode低氢型焊条low hydrogen type electrode高韧性超低氢焊条high toughness super low hydrogen electrode奥氏体焊条austenitic electrode铁素体焊条ferritic electrode不锈钢焊条stainless steel electrode珠光体耐热钢焊条pearlitic heat resistant steel electrode低温钢焊条low temperature steel electrode/ steel electrode for low te mperature铝合金焊条aluminum alloy arc w碳化钨堆焊焊条tungsten carbide surfacing electrode高锰钢堆焊焊条high manganese steel surfacing electrode双芯焊条twin electrode绞合焊条stranded electrode编织焊条braided electrode双层药皮焊条double coated electrode管状焊条flux-cored electrode气渣联合保护型药皮semi-volatile covering焊条工艺性usability of the electrode/ technicality of the electrode焊条使用性running characteristics of an electrode/ operating characteristics of an electrode 焊条熔化性melting characteristics of an electrode焊条直径core diameter焊条偏心度eccentricity (of an electrode)药皮重量系数gravity coefficient of coating焊条药皮含水量percentage of moisture for covering焊条夹吃持端bare terminal (of an electrode)焊条引弧端striking end (of an elcetrode)焊剂welding flux/ flux熔炼焊剂fused flux粘结焊剂bonded flux烧结焊剂sintered flux/ agglomerated flux窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding低氢型焊剂low hydrogen type flux高速焊剂high speed welding flux无氧焊剂oxygen-free flux低毒焊剂low poison flux磁性焊剂magnetic flux电弧焊arc welding直流电弧焊direct current arc welding交流电弧焊alternating current arc welding三相电弧焊three phase arc welding熔化电弧焊arc welding with consumable金属极电弧焊metal arc welding不熔化极电弧焊arc welding with nonconsumable碳弧焊carbon arc welding明弧焊open arc welding焊条电弧焊shielded metal arc welding (SMAW)重力焊gravity welding躺焊fire cracker welding电弧堆焊arc surfacing自动堆焊automatic surfacing躺板极堆焊surfacing by fire cracker welding带极堆焊surfacing with band-electrode振动电弧堆焊vibratory arc surfacing耐磨堆焊hardfacing埋弧焊submerged arc welding (SAW)多丝埋弧焊multiple wire submerged arc welding纵列多丝埋弧焊Tandem sequence (submerged-arc welding) 横列多丝埋弧焊series submerged arc welding (SAW-S)横列双丝并联埋弧焊transverse submerged arc welding热丝埋弧焊hot wire submerged-arc welding窄间隙埋弧焊narrow-gap submerged arc welding弧压反馈电弧焊arc voltage feedback controlling arc welding 自调节电弧焊self-adjusting arc welding适应控制焊接adaptive control welding焊剂层burden; flux layer气体保护电弧焊gas shielded arc welding保护气体protective atmosphere惰性气体inert-gas活性气体active-gas惰性气体保护焊inert-gas (arc) welding氩弧焊argon arc welding熔化极惰性气体保护电弧焊metal inert-gas arc welding钨极惰性气体保护电弧焊tungsten inert-gas arc welding钨极氢弧焊argon tungsten arc welding脉冲氢弧焊pulsed argon arc welding熔化极脉冲氢弧焊argon metal pulsed arc welding钨极脉冲氢弧焊argon tungsten pulsed arc welding热丝MIG焊hot wire MIG welding热丝TIG焊hot wire TIG welding氨弧焊helium-arc welding活性气体保护电弧焊metal active-gas arc welding混合气体保护电弧焊mixed gas arc welding二氧化碳气体保护电弧焊carbon-dioxide arc welding; CO2 arc welding 细丝CO2焊CO2 arc welding with thin wire粗丝CO2焊CO2 arc welding with thick wire磁性焊剂CO2焊unionarc welding药芯焊丝CO2焊arcos arc process; dual shield arc welding气电立焊electrogas (arc) welding氮弧焊nitrogen-arc welding水蒸气保护电弧焊water vapour arc welding原子氢焊atomic hydrogen welding冲器室中电弧焊controlled atmosphere arc welding旋转电弧焊rotating arc welding短路过渡电弧焊short circuiting arc welding焊丝横摆频率weaving speed of wire焊丝停摆时间electrode keep time of slider等离子弧焊plasma arc welding (PAW)等离子弧plasma arc等离子流plasma jet转移弧transferred arc非转移弧nontransferred arc联合型等离子弧combined plasma arc主弧main arc维弧pilot arc维弧电流pilot arc surrent双弧现象double arcing双弧临界电流critical current of double arcing等离子弧焊枪plasma (welding) torch压缩喷嘴constricting nozzle单孔喷嘴single port nozzle多孔喷嘴multiport nozzle压缩喷嘴孔径orifice diameter孔道长度orifice throat length孔道比orifice throat ratio等离子气plasma gas; orifice gas电极内缩长度electrode setback小孔效应keyhole effect小孔型等离子弧焊keyhole-mode welding熔透型等离子弧焊fusion type plasma arc welding大电流等离子弧焊high-current plasma arc welding中电流等离子弧焊intermediate-current plasma arc welding 小电流等离子弧焊low-current plasma arc welding微束等离子弧焊micro-plasma arc welding交流等离子弧焊AC plasma arc welding脉冲等离子弧焊pulsed plasma arc welding等离子弧堆焊plasma arc surfacing热丝等离子弧堆焊hot wire plasma arc surfacing粉末等离子弧堆焊plasma arc powder surfacing等离子-熔化极惰性气体保护电弧焊plasma MIG welding转移弧电源transferred arc power supply非转移弧电源nontransferred arc power supply电弧焊设备arc welding equipment电弧焊机arc welding machine直流弧焊机DC arc welding machine交流弧焊机AC arc welding machine交直流两用弧焊机AC/DC arc welding machine单站弧焊机single operator arc welding machine多站弧焊机multi-operator arc welding set固定式弧焊机stationary arc welding machine移动式弧焊机portable arc welding machine台式弧焊机bench arc welding machine内燃机驱动式弧焊机combustion engine driven arc welding set电动机驱动式弧焊机motor driven arc welding set熔化极弧焊机arc welding machine using a consumable electrode不熔化极弧焊机arc welding machine using a non-consumable electrode 脉冲弧焊机pulsed arc welding machine气体保护弧焊机gas shielded arc welding machine氩弧焊机argon arc welding machine二氧化碳弧焊机CO2 arc welding machine钨极惰性气体保护弧焊机tungsten inert-gas welding machine熔化仍惰性气体保护弧焊机metal inert-gas welding machine气电立焊机electrogas (arc) welding machine等离子弧焊机plasma arc welding machine微束等离子弧焊机micro-plasma welding equipment原子氢焊机atomic hydrogen welding apparatus埋弧焊机submerged arc welding machine弧焊电源arc welding power source直流弧焊电源DC arc welding power source交流弧焊电源AC arc welding power source交直流两用弧焊电源AC/DC arc welding power source脉冲弧焊电源pulsed arc welding power source上升特性弧焊电源rising characteristic arc welding power source平特性弧焊电源constant –voltage arc welding power source下降特性弧焊电源dropping characteristic arc welding power source垂降特性弧焊电源constant-current arc welding power source多特性弧焊电源slope-controlled arc welding power source逆变式焊接电源inverter welding power source晶体管弧焊电源transistor arc welding power source电源动特性dynamic characteristic电源外特性external characteristic弧焊变压器arc welding transformer弧焊整流器arc welding rectifier硅弧焊整流器silicon arc welding rectifier晶闸管弧焊整流器SCR arc welding rectifier; arc welding silicon controlled rectifier 脉冲弧焊整流器pulsed arc welding rectifier弧焊发电机arc welding generator焊车welding tractor焊接机头welding head行走机构traveller送丝机构wire feeder等速送丝方式constant wire-feed system变速送丝方式alternate wire-feed system跟踪装置tracer焊丝盘wire reel焊钳electrode holder焊枪welding gun电极夹electrode holder导电嘴tip; contact tube喷嘴nozzle焊剂漏斗flux-hopper高频振荡器oscillator; HF unit脉冲引弧器pulsed arc starter; surge injector脉冲稳弧器pulsed arc stabilizer脉冲激弧器pulsed arc exciter输出电抗器out put reactor镇定变阻器ballast rheostat直流分量抑制器direct current suppressor焊接回路welding circuit额定焊接电流rated welding current焊接电流调节范围range of welding current regulation空载电压open circuit voltage(no load voltage)约定负载电压conventional load voltage负载持续率duty cycle额定负载持续率rated duty cycle; standard service手工弧焊机manual arc welding machine电焊渣electroslag welding (ESW)手工电渣焊manual electroslag welding丝极电渣焊electroslag welding with wire electrode板极电渣焊electroslag welding with plate electrode熔嘴电渣焊electroslag welding with consumable nozzle 管极电渣焊electroslag welding with tube electrode窄间隙电渣焊narrow-gap electroslag welding电渣堆焊electroslag surfacing电渣焊机electrosalg welding machine熔嘴consumable nozzle; consumable wire钢档板焊接专业英汉词典(4)2006-11-08 22:23:32 作者：jql来源：浏览次数：343 网友评论0条文字大小：【大】【中】【小】评分等级：0steel shoe (192页)钢冷却板Cu-cooling plate铜滑板copper shoe渣池slag bath渣池深度depth of slag bath渣池电压voltage of slag bath电渣过程稳定性electroslag process stability焊丝间距distance between welding wires电子束焊electron beam welding (EBW)脉冲电子束焊pulsed electron beam welding加速电压acceleration voltage/ operating voltage电子束电流beam current电子束功率beam power电子束功率密度beam power density焦点focal spot焦距focal length工作距离work distance电子束焊机electron beam welding machine高真空电子束焊机full vacuum electron beam welder低真空电子束焊机partial vacuum electron beam welder非真空电子束焊机nonvacuum electron beam welder真空度vacuum电子枪electron gun二极电子枪diode gun三极电子枪triode gun偏压电极bias electrode电磁透镜electromagnetic lens电子束偏转线圈electron beam deflection coils导流系数perveance钉尖spiking激光焊laser welding/ laser beam welding连续激光焊continuous laser welding脉冲激光焊impulsed laser welding激光焊机laser welding equipment气体激光器gas laser固体激光器solid laser焦斑直径focussed diameter of the beam离焦量clearance between focal point and (plate) surface 焊缝深宽比weld seam depth-to-width ratio气焊gas welding氧乙炔焊oxy-acetylene welding氢氧焊oxy-hydrogen welding空气乙炔焊air-acetylene welding氧乙炔焊oxy-acetylene flame氢氧焰oxy-hydrogen flame氧煤气焰oxy-coal gas flame焊接火焰welding flame混合比mixing ratio混合气体可燃范围inflammable limit of the gaseous一次燃烧primary combustion二次燃烧secondary combustion燃烧速度combustion rate燃烧强度combustion intensity火焰热效率flame heating efficiency焰芯inner cone; flame cone内焰internal flame外焰flame envelope中性焰neutral flame氧化焰oxidizing flame碳化焰carburizing flame还原区reducing zone火焰稳定性flame stability回火flashback逆火backfire回烧flashback气体发生速度gasification speed焊炬torch; blow pipe等压式焊炬balanced pressure torch射吸式焊炬injector torch氧乙炔焊炬oxy-acetylene torch焊割两用炬combined cutting and welding torch 混合室mixing chamber喷射器injector焊嘴welding nozzle; welding tip液氧气化器oxygen evaporator气瓶gas cylinder乙炔瓶acetylene cylinder阀罩cylinder cap气瓶阀cylinder valve汇流排cylinder manifold减压器pressure regulator; gas regulator单级减压器single stage regulator两级减压器two stage regulator回火防止器flashback arrestor干式回火防止器dry flashback arrestor水封式回火防止器water-closing type arrestor净化器purifier乙炔发生器acetylene generator低压乙炔发生器low pressure acetylene generator热剂焊thermit welding (TW)热剂补焊thermit repair welding钢轨热剂焊thermit rail welding热剂thermit powder热剂钢水thermit steel热剂反应thermit reaction热剂溶渣thermit slag热剂铸模thermit mold; mold for thermit weld热剂坩埚thermit crucible焊筋collar水下焊underwater welding水下气体保护电弧焊underwater gas shielded arc welding水下等离子弧焊underwater plasma arc welding温式水下焊wet method underwater welding干式水下焊dry method underwater welding局部干式水下焊local dry underwater welding水帘局部干式水下焊water curtain type dry underwater welding 遥控水下焊remote controlled underwater welding电弧空腔arc bubble电阻焊resistance welding (RW)点焊spot welding; resistance spot welding凸焊projection welding缝焊seam welding滚点焊roll-spot welding连续点焊stitch welding多点焊multiple spot welding手压点焊push welding; poke welding脉冲点焊pulsation spot welding; multiple-impulse welding 双面点焊direct spot welding单面点焊indirect spot welding串联点焊series spot welding多点凸焊multiple projection welding频道进缝焊step-by-step seam welding压平缝焊mash seam welding串联缝焊series seam welding对接缝焊butt seam welding; foil-butt seam电阻对焊upset butt welding闪光对焊flash butt welding (FBW)储能焊stored energy welding电容储能点焊condenser discharge spot welding高频电阻焊high frequency resistance welding冲击电阻焊percussion welding胶接点焊spot weld-bonding; weld-bonding闪光flashing; flash过梁bridge; lintel顶锻upsetting; upset夹紧力clamping force顶锻力upsetting force; upset force电极压力electrode force; electrode pressure电极滑移electrode skid焊接循环welding cycle预压时间squeeze time锻压时间forge-delay time; forge time焊接通电时间（电阻焊）welding time (resistance welding) 预热时间preheat time加热时间heat time冷却时间cool time间歇时间quench time; chill time回火时间temper time维持时间hold time休止时间off time闪光时间flash time; flashing time顶锻时间upset time; upsetting time有电顶锻时间upset current time无电顶锻时间upset current-off time闪光速度flashing speed闪光电流flashing current; flash current顶锻电流upset current预热电流preheat current回火电流temper current调伸长度initial overhange; extension总留量total allowance闪光留量flash allowance顶锻留量upset allowance顶锻速度upset speed电极接触面electrode contact surface贴合面faying surface焊点welding spot熔核nugget熔核直径diameter of nugget。
焊接的英文单词
焊接的英文单词
“焊接”的英语单词是“weld”，英式音标：[weld]，美式音标：[weld]，可作动词和名词。
一、作动词时。
1. 例句。
- They welded a steel plate onto the plane's damaged wing.（他们把一块钢板焊接到飞机损坏的机翼上。
）
- He welded the broken pieces together.（他把碎块焊接在一起。
）
2. 用法。
- weld sth (to/onto sth)：表示将某物焊接到另一物上。
例如：weld a handle to the door（把门把焊接到门上）。
- weld sth together：把某物焊接在一起。
例如：weld the parts together （把零件焊接在一起）。
二、作名词时。
1. 例句。
- The weld on the pipe is very strong.（管道上的焊接处很牢固。
）
- They checked all the welds carefully.（他们仔细检查了所有的焊接点。
）。
welding翻译
welding翻译Welding的中文翻译是"焊接"。
焊接是一种常见的金属加工技术，通过在金属材料上加热并施加压力，将两个或更多金属部件连接在一起。
焊接广泛应用于工业制造、建筑、航空航天、汽车制造等领域。
下面是一些常见的焊接方法和用法的中英文对照例句：1. Arc Welding (电弧焊)- Shielded Metal Arc Welding (SMAW): 覆盖电弧焊Example: The welder used shielded metal arc welding to join the steel plates together. (焊工使用覆盖电弧焊将钢板连接在一起。
)- Gas Metal Arc Welding (GMAW): 气体金属电弧焊Example: Gas metal arc welding is commonly used in automotive manufacturing. (气体金属电弧焊在汽车制造中常被使用。
)2. Gas Welding (气焊)- Oxy-fuel Welding (氧气焊)Example: Oxy-fuel welding is often used for joining copper and brass materials. (氧气焊经常被用于铜和黄铜材料的连接。
)- Gas Tungsten Arc Welding (GTAW): 气体钨极氩弧焊Example: GTAW is a popular method for welding aluminum and stainless steel. (气体钨极氩弧焊是铝和不锈钢焊接的常用方法。
)3. Resistance Welding (电阻焊)- Spot Welding (点焊)Example: Spot welding is commonly used in the automotive industry for joining sheet metal components. (点焊在汽车工业中常用于连接薄板金属零件。
常用焊接中英文词语翻译
常用焊接中英文词语翻译焊接热源 welding heat source点热源 point heat source线热源 linear heat source面热源 plane heat source瞬时集中热源 instantaneous concentration heat source 热效率 thermal efficiency热能集中系数 coefficient of heat flow concentration 峰值温度 peak temperature瞬时冷却速度 momentary cooling rate冷却时间 cooling time置换氧化 substitutionary oxydation扩散氧化 diffusible oxydation脱氧 desoxydation先期脱氧 precedent desoxydation扩散脱氧 diffusible desoxydation沉淀脱氧 precipitation desoxydation扩散氢 diffusible hydrogen初始扩散氢 initial diffusible hydrogen100℃残余扩散氢 diffusible hydrogen remained at 100℃残余氢 residual hydrogen去氢 dehydrogenation去氢热处理 heat treatment for dehydrogenation脱硫 desulphurization脱磷 dephosphorization渗合金 alloying微量合金化 microalloying一次结晶组织 primary solidification structure二次结晶组织 secondary solidification structure联生结晶 epitaxial solidification焊缝结晶形态 solidification mode in weld-bead结晶层状线 ripple多边化边界 polygonization boundary结晶平均线速度 mean solidification rate针状铁素体 acicular ferrite条状铁素体 lath ferrite侧板条铁素体 ferrite side-plate晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite 粒状贝氏体 granular bainite板条马氏体 lath martensite过热组织 overheated structure魏氏组织 Widmannst?tten structureM-A组元 martensite-austenite constituent焊件失效分析 failure analysis of weldments冷裂判据 criterion of cold cracking冷裂敏感系数 cold cracking susceptibity coefficient 脆性温度区间 brittle temperature range氢脆 hydrogen embrittlement层状偏析 lamellar segregation愈合 healing effect断口金相fractography密封圈 Sealing ring铰链 Hinge把手 Handle平衡块 Balance block焊接 welding坡口 groove单面坡口 Single groove双面坡口 Double grooveⅠ形坡口 Square grooveV型坡口 Single v grooveU型坡口 Single u grooveX形坡口 Single v grooveK形坡口 Single bevel groove12Y形坡口 Single v groove with broad rood face坡口面 Groove face坡口角度 Groove angle焊缝倾角 Weld slope接头根部 Root of joint根部间隙 Root gap钝边 Root face焊接接头 Welding joint对接接头 Butt joint角接接头 Corner jointT形接头 T-joint搭接接头 Lap joint十字接头 Cross shaped joint母材 Base metal(parent metal)13填充金属 Filler metal热影响区 Heat-affected zone(HAZ) 过热区 Overheated zone焊合线 Bond line(fusion line)焊接区 Weld zone焊缝区 Weld metal area焊缝 weld连续焊缝 Continuous weld断续焊缝 Intermittent weld纵向焊缝 Longitudinal weld横向焊缝 Transverse weld对接焊缝隙 Butt weld角焊缝 Filled weld并列断续角焊缝 Chain intermittent fillet14交错断续角焊缝 Staggered intermittent fillet焊缝正面 Face of weld焊缝背面 Back of weld焊缝宽度 Weld width焊缝长度 Weld length焊缝余高 Reinforcement焊脚 Leg(of a fillet weld)焊脚长度 Leg length套管接头 Muff joint手工电弧焊 Manual arc welding(shielded metal arc welding) 直流电弧焊 Direct current arc welding交流电弧焊 alternating current arc welding弧焊变压器 Arc welding transformer15弧焊整流器 Arc welding rectifier自动焊 Automatic welding埋弧自动焊 Submerged arc welding半自动焊 Semi- automatic welding氩弧焊 Argon-arc welding二氧化碳气体保护焊 CO2 gas shielded arc welding 氧乙炔焊 Oxy-acetylene welding气割 Gas cutting碳弧气刨 Carbon arc air gouging水下切割 Underwater cutting等离子弧切割 Plasma arc cutting连续焊 Continuous welding断续焊 Intermittent welding点焊 Sport welding16对接焊 Butt welding角焊 Fillet welding搭接焊 Lap welding返修焊 Re-welding补焊 Repair welding定位焊 Tack welding封底焊 Back sealing welding打底焊 Backing welding堆焊 Surfacing(overlaying)塞焊 Plug welding槽焊 Slot welding盖面焊 Consmetic welding前倾焊 Forward welding后倾焊 Backward welding17分段退焊 Back step welding分段多层焊 Block welding深溶焊 Deep penetrating welding跳焊 Skip welding陶质衬垫焊 Ceramic backing welding 引弧 Striking the arc焊接工艺参数 Welding condition焊接电流 Welding current焊接电压 Welding voltage焊接速度 Welding speed电弧电压 Arc voltage焊丝间距 Wire spacing空载电压 Open circuit voltage熔化速度 Melting rate18送丝速度 Wire feed rate气体流量 Gas flow rate焊丝伸出长度 Wire extension极性 Polarity正极/阳极 Positive electrode负极/阴极 Navigate electrode左焊法 Leftward welding右焊法 Rightward welding电流密度 Current density线能量 Heat input预热 Preheat后热 Post-heat预热温度 Preheat temperature后热温度 Post-heat temperature19层间温度 Inter-pass temperature焊后热处理 Post-weld heat treatment 锤击 Peening全焊透 Full penetration welding熔池 Weld-pool熔深 Penetration弧长 Arc length喷射过渡 Spray transfer短路过渡 Short circuiting transfer熔滴过渡 Metal transfer焊缝成形 Appearance of weld焊缝成形系数 Form factor of weld熔敷系数 Deposition coeffcient熔敷效率 Deposition efficiency20熔合比 Penetration ratio等速送丝 Constant wire-feed system变速送丝 alternate wire-feed system电弧静特性 Static characteristic of arc 电弧动特性 dynamic characteristic of arc 焊接性试验 Weldability test焊接结构 Welded construction焊道 Bead焊层 Layer正接（正极性） Straight polarity反接（反极性） Reversed polarity焊接位置 Position of welding平焊 Flat position welding横焊 Horizontal position welding焊接缺陷1. excessive width熔宽过剩2. insufficient width 熔宽不足3. excessive reinforcement 焊缝增强过量4. insufficient reinforcement 焊缝增强不足5. mismatch 错位6. incomplete filled groove 坡口未填满7. pit 弧坑8. burn through 焊穿9. slag inclusion （single-pass weld）夹渣（单道焊）10. slag inclusion （multiple-pass weld）夹渣（多道焊）11. undercut咬边，咬肉12. overlap 焊瘤13. porosity （along entire length of weld bead）气孔（沿整个焊道）14. wormhole porosity 虫状气孔15. centerline crack 焊道中心纵向裂纹16. underbead crack 焊道下裂纹17. transverse crack 横向裂纹18. crater crack 弧坑裂纹19. root crack 根部裂纹20. fish eye 鱼眼，白点21. line inclusion 链状夹杂物22. excessive spatter 严重飞溅23. incomplete fusion 未熔合24. incomplete penetration 根部未焊透精品文档。
焊接专业英汉词典
熔接fusion welding 压接pressure welding 焊接过程welding process焊接技术welding technique焊接工艺welding technology/ procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding 焊接位置welding position熔敷顺序build-up sequence/d eposition sequence焊缝倾角weld slope/inclinatio n of weld axis焊缝转角weld rotation/angle of rotation 平焊位置flat po sition of welding横焊位置horizontal position o f welding 立焊位置vertic al position of welding仰焊位置overhead position o f welding平焊downhand wel ding/flat position welding横焊horizontal position weldi ng立焊vertical position welding 仰焊overhead position weldi ng全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
如水平固定管所进行的环缝焊接向下立焊vertical down weldi ng/downward welding in th e vertical position向上立焊vertical up welding/ upward welding in the verti cal position倾斜焊inclined position weldi ng上坡焊upward welding in th e inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the downhand position/fillet welding in the flat position平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊foreward welding (英国)/ forehand welding (美国)后倾焊backward welding(英国)/ backhand welding(美国)分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding右焊法rightward welding/backhand welding挑弧焊whipping method自动焊automatic welding手工焊manual welding/handwelding车间焊接shop welding工地焊接site welding(英国)/ field welding (美国)拘束焊接restraint welding堆焊surfacing/building up/overlaying隔离层堆焊buttering端部周边焊boxing/end return返修焊rewelding补焊repair welding塞焊plug welding槽焊slot welding衬垫焊welding with backing焊剂垫焊welding with flux backing窄间隙焊narrow-gap welding强制成形焊enclosed welding脉冲电弧焊pulsed are welding电弧点焊arc spot welding螺柱焊stud welding热风焊hot gas welding高能焊high grade energy we lding固态焊接solid-state welding 单面焊双面成形one-side weldi ng with back formation焊接条件welding condition焊接工艺参数welding parame ter极性polarity正接electrode negative/strai ght polarity反接electrode positive/rever sed polarity运条方式manipulation of elec trode焊接电流welding current焊接电流增加时间welding curr ent upslope time焊接电流衰减时间welding curr ent downslope time电流密度current density短路电流short circuit current 脉冲电流pulse level/pulse cu rrent level脉冲电流幅值pulse current a mplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage 焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy inp ut热输入heat input预热preheat后热postheat焊后热处理posweld heat trea tment/postheat treatment 预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element)坡口groove坡口面groove face坡口面角度angle of bevel (英国)/ bevel angle (美国)坡口角度included angle(英国)/groove angle(美国)坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国)/rootopening (美国)根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove withroot face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U grooveVY形坡口single compound angle groove带钝边J形坡口single J groove带钝边双J形坡口double J groove单边V形坡口single bevel groove双V形坡口double V groove不对称双V形坡口asymmetricdouble V groove双单边V形坡口double bevelgroove/K groove带垫板V形坡口V groove with backing/ single V groovewith backing喇叭形坡口flare groove锁底坡口single bevel groovewith backing locked坡形板边tapered edge焊缝weld接逢seam焊缝符号welding symbol焊缝金属weld metal填充金属filler metal熔敷金属deposited metal焊缝表面weld face/ face ofweld焊缝背面back of weld焊缝轴线axis of weld焊缝尺寸size of weld焊缝宽度weld width/ width o f weld焊缝长度weld length/ length of weld焊缝有效长度effective length of weld焊缝厚度throat depth/ throa t thickness焊缝计算厚度theoretical throa t焊缝实际厚度actual throat熔深penetration/ depth of p enetration焊缝成形appearance of weld 焊缝成形系数form factor of w eld余高reinforcement/ excess weld metal背面余高root reinforcement 削平焊缝flush weld/ weld m achined flush对接焊缝butt weld角焊缝fillet焊脚leg/ fillet weld leg角焊缝断面形状profile of fillet weld平形角焊缝flat fillet凸形角焊缝convex fillet weld 凹形角焊缝concave fillet weld 角焊缝凹度concavity侧面角焊缝side fillet weld/ fil let weld in parallel shear正面角焊缝front fillet weld/ fi llet weld in normal shear立角焊缝fillet weld in the ve rtical position横角焊缝fillet weld in the ho rizontal position平角焊缝fillet weld in the fla t position斜角焊缝oblique fillet weld连续焊缝continuous weld断续焊缝intermittent weld连续角焊缝continuous fillet w eld断续角焊缝intermittent filletweld交错断续角焊缝staggered intermittent fillet weld并列断续角焊缝chain intermittent fillet weld端接焊缝edge weld卷边焊缝flanged edge weld塞焊焊缝plug weld纵向焊缝longitudinal weld横向焊缝transverse weld环行焊缝girth weld/ circumferential weld螺旋形焊缝spiral weld/ helical weld密封焊缝seal weld承载焊缝strength weld联系焊缝connective weld定位焊缝tack weld焊道bead/ run/ pass焊波ripple焊根weld root/ root of weld焊趾weld toe/ toe封底焊道sealing run (after making main weld)/ back weld打底焊道backing weld (before making main weld)/ backweld根部焊道root pass/ root run填充焊道filling bead盖面焊道cosmetic bead/ cover pass回火焊道temper bead/ annealing bead熔透焊道penetration bead焊层layer焊接接头welded joint接头形状joint geometry等强匹配接头equalmatchingweld joint低强匹配接头undermatchingweld joint超强匹配接头overmatching weld joint接头根部root of joint对接接头butt jointI形对接接头square butt jointV形对接接头single V butt jointU形对接接头single U butt jointJ形坡口接头single J butt joint双V形对接接头double V buttjoint双单边V形对接接头double bevel butt joint/ K groove butt joint带钝边U形对接接头double Ubutt joint带钝边J形坡口接头double J joint角接接头corner jointT形接头T joint斜T形接头inclined T joint十字接头cruciform joint/ cross-shaped joint三联接头joint among threemembers搭接接头lap joint套管接头muff joint/ sleeve joint双盖板接头double strapped joint盖板接头strapped joint端接接头edge joint卷边接头flanged edge joint锁底对接接头lock butt joint斜对接接头oblique butt joint混合接头mixed joint/ composite joint有间隙接头open joint无间隙接头closed joint焊接电弧welding arc电弧形态arc shape电弧物理行为arc physics behaviour引弧striking arc引弧电压striking voltage电弧气氛arc atmosphere阴极cathode热阴极hot cathode冷阴极cold cathode阴极斑点cathode spot阴极区cathode region阴极区电场强度intensity of th e electric field in the catho de region阴极压降cathode drop阳极anode阳极斑点anode spot斑点压力spot pressure阳极区anode region阳极区电场强度intensity of th e electric field in the anode region阳极压降anode drop弧柱arc column/ arc stream 弧柱压降voltage drop in arc column弧柱电位梯度potential gradie nt in the arc column弧焰arc flame弧心arc core硬电弧forceful arc/ hard arc 软电弧soft arc旋转电弧rotating arc脉冲电弧pulsed arc脉冲喷射电弧pulsed spray ar c起皱现象puckering phenome na起皱电弧puckering arc起皱临界电流puckering critic al current间接电弧indirect arc压缩电弧compressive arc磁控电弧magnetic controllin g arc电弧力arc force 电磁力electromagnectic force电磁收缩效应pinch effect电弧飘移wandering of arc电弧稳定性arc stability电弧静特性static characteristic of arc电弧动特性dynamic characteristic of arc最小电压原理principle of minimum voltage电弧挺度arc stiffness电弧偏吹arc blow磁偏吹magnetic blow阴极清理作用cleaning actionof the cathode电弧自身调节arc self-regulation挖掘作用digging action极性效应polarity effect熔滴droplet熔滴比表面积specific surfaceof droplet熔滴过渡metal transfer过度频率transition frequency粗滴过渡globular transfer; drop transfer短路过渡short circuiting transfer喷射过渡spray transfer旋转喷射过渡rotating spray transfer脉冲喷射过渡pulsed spray transfer爆炸过渡explosive transfer渣壁过渡flux wall guided transfer熔池molten pool沸腾状熔池boiling molten pool弧坑crater熔渣slag渣系slag system渣系相图slag system diagram碱性渣basic slag酸性渣acid slag碱度basicity酸度acidity长渣long slag短渣short slag粘性熔渣viscous slag氧化物型熔渣oxide melting slag盐型熔渣salt melting slag盐-氧化物型熔渣salt-oxide melting slag熔渣流动性fluidity of the slag; slag fluidity熔渣solidified slag多孔焊渣porous slag玻璃状焊渣vitreous slag自动脱落焊渣self-releasing slag脱渣性slag detachability焊接设备welding equipment;welding set焊机welding machine; welder电焊机electric welding machine; electric welder焊接电源welding power source焊接热循环weld thermal cycle焊接温度场field of weld temperature; weld temperaturefield准稳定温度场quasi-stationarytemperature field焊接热源welding heat source点热源point heat source线热源linear heat source面热源plane heat source瞬时集中热源instantaneous concentration heat source热效率thermal efficiency热能集中系数coefficient of h eat flow concentration峰值温度peak temperature 瞬时冷却速度momentary coo ling rate冷却时间cooling time置换氧化substitutionary oxy dation扩散氧化diffusible oxydation 脱氧desoxydation先期脱氧precedent desoxyd ation扩散脱氧diffusible desoxydat ion沉淀脱氧precipitation desox ydation扩散氢diffusible hydrogen初始扩散氢initial diffusible h ydrogen100℃残余扩散氢diffusible hy drogen remained at 100℃残余氢residual hydrogen去氢dehydrogenation去氢热处理heat treatment f or dehydrogenation脱硫desulphurization脱磷dephosphorization渗合金alloying微量合金化microalloying一次结晶组织primary solidific ation structure二次结晶组织secondary solid ification structure联生结晶epitaxial solidificati on焊缝结晶形态solidification m ode in weld-bead结晶层状线ripple多边化边界polygonization bo undary结晶平均线速度mean solidific ation rate 针状铁素体acicular ferrite条状铁素体lath ferrite侧板条铁素体ferrite side-plate晶界欣素体grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite粒状贝氏体granular bainite板条马氏体lath martensite过热组织overheated structure魏氏组织Widmannst?tten structureM-A组元martensite-austenite constituent焊件失效分析failure analysisof weldments冷裂判据criterion of cold cracking冷裂敏感系数cold cracking susceptibity coefficient脆性温度区间brittle temperature range氢脆hydrogen embrittlement层状偏析lamellar segregation愈合healing effect断口金相fractography断口fracture延性断口ductile fracture韧窝断口dimple fracture脆性断口brittle fracture解理断口cleavage fracture准解理断口quasi-cleavage fracture氢致准解理断口hydrogen-embrittlement induced沿晶断口intergranular fracture穿晶断口transgranular fracture疲劳断口fatigue fracture滑移面断口glide plane fracture断口形貌fracture apperance断口试验fracture test宏观断口分析macrofractography放射区radical zone纤维区fibrous zone剪切唇区shear lip aone焊接性weldability使用焊接性service weldability工艺焊接性fabrication weldability冶金焊接性metallurgical weldability热焊接性thermal weldability母材base metal; parent metal焊接区weld zone焊态as-welded (AW)母材熔化区fusion zone半熔化区partial melting region未混合区unmixed zone熔合区bond area熔合线weld junction (英)；bond line (美)热影响区heat-affected zone(HAZ)过热区overheated zone粗晶区coarse grained region细晶区fine grained region过渡区transition zone硬化区hardened zone碳当量carbon equivalent铬当量chromium equivalent镍当量nickel equivalent舍夫勒组织图Schaeffler's diagram德龙组织图Delong’s diagram连续冷却转变图（CCT图）continuous cooling transformation裂纹敏感性cracking sensibilit y焊接裂纹weld crack焊缝裂纹weld metal crack焊道裂纹bead crack弧坑裂纹crater crack热影响区裂纹heat-affected z one crack纵向裂纹longitudinal crack 横向裂纹transverse crack微裂纹micro-crack; micro-fi ssure热裂纹hot crack凝固裂纹solidification crack 晶间裂纹intercrystalline crac k穿晶裂纹transcrystalline cra ck多边化裂纹polygonization cr ack液化裂纹liquation crack失延裂纹ductility-dip crack 冷裂纹cold crack延迟裂纹delayed crack氢致裂纹hydrogen-induced c rack焊道下裂纹underbead crack 焊根裂纹root crack焊趾裂纹toe crack锯齿形裂纹chevron cracking 消除应力处理裂纹stress relief annealing crack (SR crack) 再热裂纹reheat crack焊缝晶间腐蚀weld intercryct alline corrosion刀状腐蚀knife line attack敏化区腐蚀weld decay层状撕裂lamellar tearing焊接性试验weldability裂纹试验cracking testIIW裂纹试验IIW cracking te stY形坡口裂纹试验slit type cra cking test 分块形槽热裂纹试验segmented circular groove cracking testH形裂纹试验H-type crackingtest鱼骨形裂纹试验fishbone cracking test指形裂纹试验finger (cracking)testT形裂纹试验Tee type cracking test环形槽裂纹试验circular-groove cracking test可调拘束裂纹试验varestrainttestBWRA奥氏体钢裂纹试验BWRA cracking test for austenitie steel圆棒裂纹试验bar type cracking test; round bar crackingtest里海裂纹试验Lehigh restraintcracking test圆形镶块裂纹试验circular-path cracking test十字接头裂纹试验cruciform cracking testZ向窗口拘束裂纹试验Z-direction window type restraint cracking testG-BOP焊缝金属裂纹试验G-BOP weld metal crack test巴特尔焊道下裂纹试验Battelletype underbead cracking testU形拉伸试验U-tension test缪雷克期热裂纹试验Murex hot cracking test菲斯柯裂纹试验FISCO (type)cracking testCTS裂纹试验controlled thermal severity拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test刚性拘束裂纹试验（RRC试验）rigid restraint cracking test插销试验implant testTigamajig 薄板焊接裂纹试验Tigamajing thin plate cracking test焊道纵向弯曲试验longitudinal-bead test柯麦雷尔弯曲试验Kommerellbead bend test肯泽尔弯曲试验Kinzel test缺口弯曲试验notch bend test热朔性试验hot-ductility test热影响区冲击试验impact testof HAZ热影响区模拟试验synthetic heat-affected zone test最高硬度试验maximum hardness test落锤试验NRL (Naval Research Laboratory)测氢试验Hydrogen test焊接材料电极焊接材料welding consumables电极electrode熔化电极consumable electrode不熔化电极nonconsumable electrode钨电极tungsten electrode焊丝welding wire. Welding rod实心焊丝solid wire渡铜焊丝copper-plating welding wire自保护焊丝self-shielded welding wire药芯焊丝flux-cored wire复合焊丝combined wire堆焊焊丝surfacing welding rod填充焊丝filler wire焊条electrode/ covered elect rode焊芯core wire药皮coating (of an electrode) / covering (of an electrode) 涂料coating flux/coating ma terial造气剂gas forming constitue nts造渣剂slag forming constitue nts合金剂alloying constituent脱氧剂dioxidizer稳弧剂arc stabilizer粘接剂binder水玻璃water glass水玻璃模数modules of water glass酸性焊条acid electrode高钛型焊条high titania (type) electrode钛钙型焊条lime titania type electrode钛铁矿形焊条ilmenite type el ectrode氧化铁型焊条iron oxide type electrode/ high iron oxide t ype electrode高纤维素型焊条high cellulose (type) electrode石墨型焊条graphite type elec trode碱性焊条basic electrode/ lim e type covered electrode低氢型焊条low hydrogen typ e electrode高韧性超低氢焊条high toughn ess super low hydrogen ele ctrode奥氏体焊条austenitic electrod e铁素体焊条ferritic electrode 不锈钢焊条stainless steel ele ctrode珠光体耐热钢焊条pearlitic heat resistant steel electrode低温钢焊条low temperature steel electrode/ steel electrode for low temperature铝合金焊条aluminum alloy arc welding electrode铜合金焊条copper-alloy arcwelding electrode铜芯铸铁焊条cast iron electrode with steel core纯镍铸铁焊条pure nickel castiron electrode球墨铸铁焊条electrode for welding spheroidal graphite cast iron铸芯焊条electrode with castcore wire镍基合金焊条nickel base alloy covered electrode蒙乃尔焊条Monel electrode纯铁焊条pure iron electrode渗铝钢焊条alumetized steel electrode高效率焊条high efficiency electrode铁粉焊条iron powder electrode底层焊条backing welding electrode深熔焊条deep penetration electrode重力焊条gravity electrode立向下焊条electrode for vertical down position welding节能焊条saving energy electrode水下焊条underwater weldingelectrode耐海水腐蚀焊条seawater corrosion resistant steel electrode低尘低毒焊条low-fume and harmfulless electrode/low-fume and low-toxic electrode堆焊焊条surfacing electrode耐磨堆焊焊条hardfacing electrode钴基合金堆焊焊条cobalt basealloy surfacing electrode碳化钨堆焊焊条tungsten carbide surfacing electrode高锰钢堆焊焊条high manganese steel surfacing electrode双芯焊条twin electrode绞合焊条stranded electrode编织焊条braided electrode双层药皮焊条double coated electrode管状焊条flux-cored electrode气渣联合保护型药皮semi-volatile covering焊条工艺性usability of the electrode/ technicality of theelectrode焊条使用性running characteristics of an electrode/ operating characteristics of an electrode焊条熔化性melting characteristics of an electrode焊条直径core diameter焊条偏心度eccentricity (of anelectrode)药皮重量系数gravity coefficient of coating焊条药皮含水量percentage ofmoisture for covering焊条夹吃持端bare terminal (of an electrode)焊条引弧端striking end (of an elcetrode)焊剂welding flux/ flux熔炼焊剂fused flux粘结焊剂bonded flux烧结焊剂sintered flux/ agglomerated flux窄间隙埋弧焊焊剂flux for narr ow-gap submerged arc wel ding低氢型焊剂low hydrogen typ e flux高速焊剂high speed welding flux无氧焊剂oxygen-free flux低毒焊剂low poison flux磁性焊剂magnetic flux电弧焊arc welding直流电弧焊direct current arc welding交流电弧焊alternating curre nt arc welding三相电弧焊three phase arc welding熔化电弧焊arc welding with consumable金属极电弧焊metal arc weldi ng不熔化极电弧焊arc welding with nonconsumable碳弧焊carbon arc welding明弧焊open arc welding焊条电弧焊shielded metal ar c welding (SMAW)重力焊gravity welding躺焊fire cracker welding电弧堆焊arc surfacing自动堆焊automatic surfacing 躺板极堆焊surfacing by fire cracker welding带极堆焊surfacing with ban d-electrode振动电弧堆焊vibratory arc s urfacing耐磨堆焊hardfacing埋弧焊submerged arc weldi ng (SAW)多丝埋弧焊multiple wire sub merged arc welding纵列多丝埋弧焊Tandem sequ ence (submerged-arc welding)横列多丝埋弧焊series submerged arc welding (SAW-S)横列双丝并联埋弧焊transverse submerged arc welding热丝埋弧焊hot wire submerged-arc welding窄间隙埋弧焊narrow-gap submerged arc welding弧压反馈电弧焊arc voltage feedback controlling arc welding自调节电弧焊self-adjusting arc welding适应控制焊接adaptive control welding焊剂层burden; flux layer气体保护电弧焊gas shieldedarc welding保护气体protective atmosphere惰性气体inert-gas活性气体active-gas惰性气体保护焊inert-gas (arc)welding氩弧焊argon arc welding熔化极惰性气体保护电弧焊metal inert-gas arc welding钨极惰性气体保护电弧焊tungsten inert-gas arc welding钨极氢弧焊argon tungsten arc welding脉冲氢弧焊pulsed argon arcwelding熔化极脉冲氢弧焊argon metal pulsed arc welding钨极脉冲氢弧焊argon tungsten pulsed arc welding热丝MIG焊hot wire MIG welding热丝TIG焊hot wire TIG welding氨弧焊helium-arc welding活性气体保护电弧焊metal active-gas arc welding混合气体保护电弧焊mixed gas arc welding二氧化碳气体保护电弧焊carbon-dioxide arc welding; CO2arc welding细丝CO2焊CO2 arc weldingwith thin wire粗丝CO2焊CO2 arc weldingwith thick wire磁性焊剂CO2焊unionarc welding药芯焊丝CO2焊arcos arc process; dual shield arc welding气电立焊electrogas (arc) welding氮弧焊nitrogen-arc welding水蒸气保护电弧焊water vapour arc welding原子氢焊atomic hydrogen welding冲器室中电弧焊controlled atmosphere arc welding旋转电弧焊rotating arc welding短路过渡电弧焊short circuiting arc welding焊丝横摆频率weaving speedof wire焊丝停摆时间electrode keeptime of slider等离子弧焊plasma arc welding (PAW)等离子弧plasma arc等离子流plasma jet转移弧transferred arc非转移弧nontransferred arc联合型等离子弧combined plasma arc主弧main arc维弧pilot arc维弧电流pilot arc surrent双弧现象double arcing双弧临界电流critical current of double arcing等离子弧焊枪plasma (weldin g) torch压缩喷嘴constricting nozzle 单孔喷嘴single port nozzle 多孔喷嘴multiport nozzle压缩喷嘴孔径orifice diameter 孔道长度orifice throat lengt h孔道比orifice throat ratio等离子气plasma gas; orifice gas电极内缩长度electrode setba ck小孔效应keyhole effect小孔型等离子弧焊keyhole-mo de welding熔透型等离子弧焊fusion type plasma arc welding大电流等离子弧焊high-curren t plasma arc welding中电流等离子弧焊intermediat e-current plasma arc weldin g小电流等离子弧焊low-current plasma arc welding微束等离子弧焊micro-plasma arc welding交流等离子弧焊AC plasma ar c welding脉冲等离子弧焊pulsed plasm a arc welding等离子弧堆焊plasma arc surf acing热丝等离子弧堆焊hot wire pl asma arc surfacing粉末等离子弧堆焊plasma arc powder surfacing等离子-熔化极惰性气体保护电弧焊plasma MIG welding转移弧电源transferred arc p ower supply 非转移弧电源nontransferredarc power supply电弧焊设备arc welding equipment电弧焊机arc welding machine直流弧焊机DC arc weldingmachine交流弧焊机AC arc weldingmachine交直流两用弧焊机AC/DC arcwelding machine单站弧焊机single operator arc welding machine多站弧焊机multi-operator arc welding set固定式弧焊机stationary arcwelding machine移动式弧焊机portable arc welding machine台式弧焊机bench arc welding machine内燃机驱动式弧焊机combustion engine driven arc weldingset电动机驱动式弧焊机motor driven arc welding set熔化极弧焊机arc welding machine using a consumable electrode不熔化极弧焊机arc weldingmachine using a non-consumable electrode脉冲弧焊机pulsed arc welding machine气体保护弧焊机gas shieldedarc welding machine氩弧焊机argon arc weldingmachine二氧化碳弧焊机CO2 arc welding machine钨极惰性气体保护弧焊机tungsten inert-gas welding machine熔化仍惰性气体保护弧焊机metal inert-gas welding machine气电立焊机electrogas (arc)welding machine等离子弧焊机plasma arc welding machine微束等离子弧焊机micro-plasma welding equipment原子氢焊机atomic hydrogenwelding apparatus埋弧焊机submerged arc welding machine弧焊电源arc welding powersource直流弧焊电源DC arc weldingpower source交流弧焊电源AC arc weldingpower source交直流两用弧焊电源AC/DC arc welding power source脉冲弧焊电源pulsed arc welding power source上升特性弧焊电源rising characteristic arc welding powersource平特性弧焊电源constant –voltage arc welding power source下降特性弧焊电源dropping characteristic arc welding power source垂降特性弧焊电源constant-current arc welding power source多特性弧焊电源slope-controlled arc welding power source逆变式焊接电源inverter welding power source晶体管弧焊电源transistor arcwelding power source电源动特性dynamic characteristic电源外特性external characte ristic弧焊变压器arc welding trans former弧焊整流器arc welding rectif ier硅弧焊整流器silicon arc weld ing rectifier晶闸管弧焊整流器SCR arc we lding rectifier; arc welding s ilicon controlled rectifier脉冲弧焊整流器pulsed arc w elding rectifier弧焊发电机arc welding gene rator焊车welding tractor焊接机头welding head行走机构traveller送丝机构wire feeder等速送丝方式constant wire-f eed system变速送丝方式alternate wire-f eed system跟踪装置tracer焊丝盘wire reel焊钳electrode holder焊枪welding gun电极夹electrode holder导电嘴tip; contact tube喷嘴nozzle焊剂漏斗flux-hopper高频振荡器oscillator; HF uni t脉冲引弧器pulsed arc starter; surge injector脉冲稳弧器pulsed arc stabili zer脉冲激弧器pulsed arc excite r输出电抗器out put reactor镇定变阻器ballast rheostat直流分量抑制器direct current suppressor焊接回路welding circuit 额定焊接电流rated welding current焊接电流调节范围range of welding current regulation空载电压open circuit voltage(no load voltage)约定负载电压conventional load voltage负载持续率duty cycle额定负载持续率rated duty cycle; standard service手工弧焊机manual arc welding machine电焊渣electroslag welding(ESW)手工电渣焊manual electroslag welding丝极电渣焊electroslag welding with wire electrode板极电渣焊electroslag welding with plate electrode熔嘴电渣焊electroslag welding with consumable nozzle管极电渣焊electroslag welding with tube electrode窄间隙电渣焊narrow-gap electroslag welding电渣堆焊electroslag surfacing电渣焊机electrosalg weldingmachine熔嘴consumable nozzle; consumable wire钢档板steel shoe (192页)钢冷却板Cu-cooling plate铜滑板copper shoe渣池slag bath渣池深度depth of slag bath渣池电压voltage of slag bath电渣过程稳定性electroslag process stability焊丝间距distance between welding wires电子束焊electron beam welding (EBW)脉冲电子束焊pulsed electronbeam welding加速电压acceleration voltage/ operating voltage电子束电流beam current电子束功率beam power电子束功率密度beam power density焦点focal spot焦距focal length工作距离work distance电子束焊机electron beam welding machine高真空电子束焊机full vacuumelectron beam welder低真空电子束焊机partial vacuum electron beam welder非真空电子束焊机nonvacuumelectron beam welder真空度vacuum电子枪electron gun二极电子枪diode gun三极电子枪triode gun偏压电极bias electrode电磁透镜electromagnetic lens电子束偏转线圈electron beamdeflection coils导流系数perveance钉尖spiking激光焊laser welding/ laser beam welding连续激光焊continuous laserwelding脉冲激光焊impulsed laser welding激光焊机laser welding equipment气体激光器gas laser固体激光器solid laser焦斑直径focussed diameter of the beam离焦量clearance between focal point and (plate) surface焊缝深宽比weld seam depth-to-width ratio气焊gas welding氧乙炔焊oxy-acetylene weldi ng氢氧焊oxy-hydrogen weldin g空气乙炔焊air-acetylene wel ding氧乙炔焊oxy-acetylene flam e氢氧焰oxy-hydrogen flame 氧煤气焰oxy-coal gas flame 焊接火焰welding flame混合比mixing ratio混合气体可燃范围inflammable limit of the gaseous一次燃烧primary combustio n二次燃烧secondary combusti on燃烧速度combustion rate燃烧强度combustion intensit y火焰热效率flame heating effi ciency焰芯inner cone; flame cone 内焰internal flame外焰flame envelope中性焰neutral flame氧化焰oxidizing flame碳化焰carburizing flame还原区reducing zone火焰稳定性flame stability回火flashback逆火backfire回烧flashback气体发生速度gasification spe ed焊炬torch; blow pipe等压式焊炬balanced pressur e torch射吸式焊炬injector torch氧乙炔焊炬oxy-acetylene tor ch焊割两用炬combined cuttingand welding torch混合室mixing chamber喷射器injector焊嘴welding nozzle; welding tip液氧气化器oxygen evaporator气瓶gas cylinder乙炔瓶acetylene cylinder阀罩cylinder cap气瓶阀cylinder valve汇流排cylinder manifold减压器pressure regulator; gas regulator单级减压器single stage regulator两级减压器two stage regulator回火防止器flashback arrestor干式回火防止器dry flashbackarrestor水封式回火防止器water-closing type arrestor净化器purifier乙炔发生器acetylene generator低压乙炔发生器low pressureacetylene generator热剂焊thermit welding (TW)热剂补焊thermit repair welding钢轨热剂焊thermit rail welding热剂thermit powder热剂钢水thermit steel热剂反应thermit reaction热剂溶渣thermit slag热剂铸模thermit mold; moldfor thermit weld热剂坩埚thermit crucible焊筋collar水下焊underwater welding水下气体保护电弧焊underwater gas shielded arc welding水下等离子弧焊underwater plasma arc welding温式水下焊wet method underwater welding干式水下焊dry method underwater welding局部干式水下焊local dry underwater welding水帘局部干式水下焊water curtain type dry underwater welding遥控水下焊remote controlledunderwater welding电弧空腔arc bubble2006-09-06 | 焊接专业英汉词典（2）电阻焊resistance welding (RW)点焊spot welding; resistance spot welding凸焊projection welding缝焊seam welding滚点焊roll-spot welding连续点焊stitch welding多点焊multiple spot welding手压点焊push welding; pokewelding脉冲点焊pulsation spot welding; multiple-impulse welding双面点焊direct spot welding单面点焊indirect spot welding串联点焊series spot welding多点凸焊multiple projectionwelding频道进缝焊step-by-step seam welding压平缝焊mash seam welding。
常用焊接中英文词语翻译
常用焊接中英文词语翻译焊接热源 welding heat source点热源 point heat source线热源 linear heat source面热源 plane heat source瞬时集中热源 instantaneous concentration heat source 热效率 thermal efficiency热能集中系数 coefficient of heat flow concentration 峰值温度 peak temperature瞬时冷却速度 momentary cooling rate冷却时间 cooling time置换氧化 substitutionary oxydation扩散氧化 diffusible oxydation脱氧 desoxydation先期脱氧 precedent desoxydation扩散脱氧 diffusible desoxydation沉淀脱氧 precipitation desoxydation扩散氢 diffusible hydrogen初始扩散氢 initial diffusible hydrogen100℃残余扩散氢 diffusible hydrogen remained at 100℃残余氢 residual hydrogen去氢 dehydrogenation去氢热处理 heat treatment for dehydrogenation脱硫 desulphurization脱磷 dephosphorization渗合金 alloying微量合金化 microalloying一次结晶组织 primary solidification structure二次结晶组织 secondary solidification structure联生结晶 epitaxial solidification焊缝结晶形态 solidification mode in weld-bead结晶层状线 ripple多边化边界 polygonization boundary结晶平均线速度 mean solidification rate针状铁素体 acicular ferrite条状铁素体 lath ferrite侧板条铁素体 ferrite side-plate晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite 粒状贝氏体 granular bainite板条马氏体 lath martensite过热组织 overheated structure魏氏组织 Widmannst?tten structureM-A组元 martensite-austenite constituent焊件失效分析 failure analysis of weldments冷裂判据 criterion of cold cracking冷裂敏感系数 cold cracking susceptibity coefficient 脆性温度区间 brittle temperature range氢脆 hydrogen embrittlement层状偏析 lamellar segregation愈合 healing effect断口金相fractography密封圈 Sealing ring铰链 Hinge把手 Handle平衡块 Balance block焊接 welding坡口 groove单面坡口 Single groove双面坡口 Double grooveⅠ形坡口 Square grooveV型坡口 Single v grooveU型坡口 Single u grooveX形坡口 Single v grooveK形坡口 Single bevel groove12Y形坡口 Single v groove with broad rood face坡口面 Groove face坡口角度 Groove angle焊缝倾角 Weld slope接头根部 Root of joint根部间隙 Root gap钝边 Root face焊接接头 Welding joint对接接头 Butt joint角接接头 Corner jointT形接头 T-joint搭接接头 Lap joint十字接头 Cross shaped joint母材 Base metal(parent metal)13填充金属 Filler metal热影响区 Heat-affected zone(HAZ) 过热区 Overheated zone焊合线 Bond line(fusion line)焊接区 Weld zone焊缝区 Weld metal area焊缝 weld连续焊缝 Continuous weld断续焊缝 Intermittent weld纵向焊缝 Longitudinal weld横向焊缝 Transverse weld对接焊缝隙 Butt weld角焊缝 Filled weld并列断续角焊缝 Chain intermittent fillet14交错断续角焊缝 Staggered intermittent fillet焊缝正面 Face of weld焊缝背面 Back of weld焊缝宽度 Weld width焊缝长度 Weld length焊缝余高 Reinforcement焊脚 Leg(of a fillet weld)焊脚长度 Leg length套管接头 Muff joint手工电弧焊 Manual arc welding(shielded metal arc welding) 直流电弧焊 Direct current arc welding交流电弧焊 alternating current arc welding弧焊变压器 Arc welding transformer15弧焊整流器 Arc welding rectifier自动焊 Automatic welding埋弧自动焊 Submerged arc welding半自动焊 Semi- automatic welding氩弧焊 Argon-arc welding二氧化碳气体保护焊 CO2 gas shielded arc welding 氧乙炔焊 Oxy-acetylene welding气割 Gas cutting碳弧气刨 Carbon arc air gouging水下切割 Underwater cutting等离子弧切割 Plasma arc cutting连续焊 Continuous welding断续焊 Intermittent welding点焊 Sport welding16对接焊 Butt welding角焊 Fillet welding搭接焊 Lap welding返修焊 Re-welding补焊 Repair welding定位焊 Tack welding封底焊 Back sealing welding打底焊 Backing welding堆焊 Surfacing(overlaying)塞焊 Plug welding槽焊 Slot welding盖面焊 Consmetic welding前倾焊 Forward welding后倾焊 Backward welding17分段退焊 Back step welding分段多层焊 Block welding深溶焊 Deep penetrating welding跳焊 Skip welding陶质衬垫焊 Ceramic backing welding 引弧 Striking the arc焊接工艺参数 Welding condition焊接电流 Welding current焊接电压 Welding voltage焊接速度 Welding speed电弧电压 Arc voltage焊丝间距 Wire spacing空载电压 Open circuit voltage熔化速度 Melting rate18送丝速度 Wire feed rate气体流量 Gas flow rate焊丝伸出长度 Wire extension极性 Polarity正极/阳极 Positive electrode负极/阴极 Navigate electrode左焊法 Leftward welding右焊法 Rightward welding电流密度 Current density线能量 Heat input预热 Preheat后热 Post-heat预热温度 Preheat temperature后热温度 Post-heat temperature19层间温度 Inter-pass temperature焊后热处理 Post-weld heat treatment 锤击 Peening全焊透 Full penetration welding熔池 Weld-pool熔深 Penetration弧长 Arc length喷射过渡 Spray transfer短路过渡 Short circuiting transfer熔滴过渡 Metal transfer焊缝成形 Appearance of weld焊缝成形系数 Form factor of weld熔敷系数 Deposition coeffcient熔敷效率 Deposition efficiency20熔合比 Penetration ratio等速送丝 Constant wire-feed system变速送丝 alternate wire-feed system电弧静特性 Static characteristic of arc 电弧动特性 dynamic characteristic of arc 焊接性试验 Weldability test焊接结构 Welded construction焊道 Bead焊层 Layer正接（正极性） Straight polarity反接（反极性） Reversed polarity焊接位置 Position of welding平焊 Flat position welding横焊 Horizontal position welding焊接缺陷1. excessive width熔宽过剩2. insufficient width 熔宽不足3. excessive reinforcement 焊缝增强过量4. insufficient reinforcement 焊缝增强不足5. mismatch 错位6. incomplete filled groove 坡口未填满7. pit 弧坑8. burn through 焊穿9. slag inclusion （single-pass weld）夹渣（单道焊）10. slag inclusion （multiple-pass weld）夹渣（多道焊）11. undercut咬边，咬肉12. overlap 焊瘤13. porosity （along entire length of weld bead）气孔（沿整个焊道）14. wormhole porosity 虫状气孔15. centerline crack 焊道中心纵向裂纹16. underbead crack 焊道下裂纹17. transverse crack 横向裂纹18. crater crack 弧坑裂纹19. root crack 根部裂纹20. fish eye 鱼眼，白点21. line inclusion 链状夹杂物22. excessive spatter 严重飞溅23. incomplete fusion 未熔合24. incomplete penetration 根部未焊透精品文档。
焊接英汉词典
焊接英汉词典2009-1-18 22:13:34 来源:来自网络作者:未知【大中小】点击： 230次actual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝中心线; 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊 continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机electric-weld pipe mill电焊管机emporary weld临时点定焊缝excess weld metal焊缝补强金属; 补强; 补强焊料; 补强金属excess weld metal(焊缝的)余高explosive weld爆炸焊接face of weld焊缝表面; 焊接面fibrous weld纤维状焊缝field weld现场焊接filler weld填角焊缝fillet weld角焊缝; 填角焊; 贴角焊fillet weld in normal shear (搭接接头的)正面角焊缝fillet weld in parallel shear侧面角焊缝; 侧面填角焊fillet weld in the flat position角接平焊; 水平角焊缝fillet weld in the horizontal position横向角焊缝fillet weld size焊角尺寸; 填角焊缝尺寸flame weld火焰焊接flange weld卷边焊缝; 卷边焊缝flange-to-web weld卷边焊缝; 卷边焊缝flanged butt weld弯边对接焊flanged edge weld卷边焊; 卷边焊flash butt weld闪光焊flash weld闪速对焊flat faced fillet weld平顶角焊缝焊接flat fillet weld平角焊ing of fillet weld角焊缝平焊; 船形角焊flush fillet weld平角焊flush weld削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld锻焊焊缝forged weld (焊后锻压的)锻压焊缝form factor of the weld焊缝成形系数formation of weld焊缝成形front fillet weld正侧面填角焊缝; 正面填角焊front(al) fillet weld正面角焊缝full fillet weld满角焊缝; 全角焊full penetration butt weld满对接焊full weld满焊full-fillet weld满角焊full-sized weld全尺寸焊缝full-strength weld (与母材等强)等强焊缝gap weld特殊点焊; 双极单点焊gas-pressure weld气压焊girth weld环形焊缝gravity weld倚焊groove weld坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint有坡口焊接接头hammer weld锻焊hand weld手焊焊缝height of reinforcement of weld加强焊缝高度helical-weld pipe螺旋焊管high performance weld flux高性能焊剂horizontal fillet weld横向角缝焊接horizontal weld横向焊缝horizontal-vertical fillet weld横向垂直角焊缝hot weld encapsulation热焊封袋hydraulic automatic weld液压自动焊接hydraulic weld process液压焊接法inclined weld斜焊inconel weld单面焊缝incorrect weld profile焊缝形状不对incorrect weld size焊缝尺寸不对induction weld mill感应焊管机inside corner weld内角焊接inside fillet weld内角焊接inside weld内焊缝insufficient or excess reinforcement of weld加强焊缝不足或过量 intermittent fillet weld间断角缝焊接; 断续角焊缝intermittent weld断续焊; 断续焊缝jam weld对接焊; 对头焊接lap fillet weld搭接角焊缝laser (beam) weld (ing)激光焊lateral weld侧焊; 侧面焊缝leg of a fillet weld角焊缝; 角焊缝焊脚leg of fillet weld圆角焊肉厚length of weld焊缝长度light closing weld轻连续焊接light fillet weld轻型填角焊; 小填角焊light weld轻焊缝Lincoln weld埋弧自动焊longitudinal fillet weld纵向角焊longitudinal weld纵向焊缝longitudinal weld (焊接用语)纵缝loose weld脱焊main weld主焊缝mash seam weld压薄缝焊; 滚压焊mash weld点焊; 点压焊melt thru weld熔透焊缝melt-through weld透溶焊melten weld pool焊接熔池melting through weld熔透焊缝miter weld平顶角焊缝; 斜接角焊缝molten weld metal熔融焊接金属mulitple impulse weld多脉冲焊缝multilayer weld多层焊缝multipass weld多道焊缝multiple arc weld多弧焊缝multiple-electrode submerged arc weld多电极埋弧焊 multiple-pass weld多道焊缝; 多路焊接multirun weld多道焊缝nonpressure thermit weld不加压热剂焊缝normal weld正常焊接oblique fillet weld斜交角焊缝; 斜角焊接one-pass weld单层焊缝open butt weld开口对接焊open weld留间隙焊缝; 空隙焊outside weld外焊缝over weld过焊overhead fillet weld仰焊角焊缝overhead weld仰焊oversize weld超尺寸焊缝oxygen weld氧气焊接parallel-arc weld并列弧焊patch weld补焊; 补孔焊缝Peltier's cross weld珀耳帖交叉焊接penetration weld熔透焊缝percussion weld冲击焊缝; 冲击焊接periphera weld环形焊缝pitch of weld焊缝接距; 焊线距plain butt weld无坡口对接焊; 平头对接焊缝plasma-arc weld等离子弧焊接plug weld塞焊焊缝point of weld焊接点point weld点焊poor weld劣质焊缝; 有缺陷的焊缝porous weld多孔焊缝; 疏松焊缝positioned weld平位焊缝; 暂焊post weld annealed (PWA)焊后退火poured weld铸焊焊缝powder weld process粉末焊接法practice weld试验焊缝pressure weld压焊pressure-controlled weld压力控制焊接pressure-tight weld气密焊; 密封焊道principal weld主要焊缝profile of fillet weld填角焊缝轮廓progress of weld焊向projection weld凸焊; 凸焊焊缝projection weld machine凸点电阻焊机pulsating weld脉冲接触焊push weld挤焊quilting weld钉焊reinforced butt weld补强的对接焊缝; 补强式对接焊缝 reinforced weld加强焊接reinforcement of weld焊缝加厚; 补强金属; 加强焊缝 resistance weld mill电阻焊管机resistance weld pipe电阻焊管resonance butt weld谐振式对接焊restarting a weld再引弧ripple weld鳞状焊缝rivet weld电铆; 电铆焊缝root face of weld焊缝根部钝边root gap of weld焊缝根部间隙root of weld焊缝根部; 焊根root opening of weld焊缝根部间隙root radius of weld焊缝坡口根部半径sagged weld下垂焊缝scarf weld楔口焊接seal weld填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝 sealing weld封焊seam weld滚焊semi-automatic arc weld半自动电弧焊sequence weld timer序列焊接时间调节器shallow weld浅焊shop weld工厂焊接shot weld点焊shoulder of weld焊缝根部钝边side fillet weld侧面角焊缝; 侧面填角焊缝; 侧面贴角焊 side lap weld侧边搭接焊; 弯边搭焊缝side weld侧焊缝; 边焊single lap weld单搭接焊single strap butt weld单面盖板对接焊single-bevel groove weld单斜角槽焊single-fillet weld单边角接焊缝single-pass weld单道焊site weld现场焊接; 安装焊; 安装焊接size of a fillet weld焊角尺寸size of weld焊件的大小; 焊区尺寸skew weld斜焊skin weld表面焊接sleeve weld套筒焊接slip-weld hanger卡瓦焊接套管挂slot weld槽塞焊; 长孔焊; 开槽搭焊缝; 切口焊缝ing slotted weld槽焊slotted lap weld切口搭接焊smooth fillet weld平填角焊缝socket weld ends承插焊接端soft-weld铜镍焊条合金solvent weld溶剂焊接space of intermittent weld断续焊缝间距; 断续焊间距spiral weld螺旋形焊缝spiral weld-pipe mill螺旋焊管机spot weld焊点spot weld bonding胶结点焊spot weld nugget点焊熔核spreading weld宽缝焊接; 加宽的焊缝square butt weld平头对接焊缝square groove weld无坡口槽焊staggered intermittent fillet weld (ing)交错断续角焊staggered intermittent weld交错断续焊缝; 交错间断焊staggered plug weld交错塞焊standard reinforced fillet weld标准加强角焊缝stick-out weld未熔合点焊接头stitch-and-seam weld点线焊straight butt weld无坡口对接接头strapped weld搭板对接焊缝strength weld受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld强固焊缝surface of weld焊缝表面surface weld表面焊缝surface weld metal buildup表面焊缝金属的形成synthetic apparatus for weld thermal cycle焊接热循环模拟装置 T weld丁字接头焊缝T-filled weld丁字形角焊T-fillet weld丁字接头角焊缝tack weld定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding)定位焊tandem arc weld前后弧焊temporary weld临时点固焊缝tension weld受拉焊缝test weld试焊throat depth (thickness) of fillet weld角焊缝厚度throat of fillet weld凹角焊喉; 填角焊缝喉长throat of weld凹角焊喉tight weld密封焊接; 致密焊缝tight-strong weld密实强固焊缝toe of the weld焊缝边界toe of weld焊趾toe weld趾部焊缝torch weld气焊焊缝total amount of weld fumes焊接发尘量transverse fillet weld横向角焊缝; 正面角焊transverse weld横向焊缝trial weld试验焊接undercut weld底切焊接undressed weld (增加焊缝)未加工焊缝unequal fillet weld焊脚不等的角焊缝unfitness of butt weld焊缝对口错边量union-melt weld埋弧焊unload weld非承载焊缝unspaced butted weld无间隙对接焊缝upgrading of boiler weld锅炉焊缝加强vertical fillet weld立焊角焊缝vertical weld立焊weak weld不强固焊缝weaving weld横向摆动焊缝weld焊; 焊接的; 补焊weld all around围焊weld appearance焊缝外观weld assembly焊接组件weld back-up焊缝背垫weld backing焊缝衬垫weld bead焊缝; 熔敷焊道weld bead height焊缝高度weld beading焊瘤weld bond熔合线weld bridge seam搭桥焊缝; 桥接焊缝weld cap焊帽weld center line焊缝中心线weld collar加强焊缝焊瘤weld crack焊接裂纹weld crater熔池weld crosswise交叉焊接weld decay焊缝腐蚀; 焊接接头晶间腐蚀; 焊接侵蚀; 焊接区晶间腐蚀 weld decay (焊接后)敏化区腐蚀weld defect焊接缺陷weld delay time焊接延迟时间weld deposit堆焊weld deposits cleaning焊接熔敷金属清理weld edge焊缝边缘; 焊缝表面边缘weld edgewise沿边焊接weld flange connection焊接法兰连接weld flash焊瘤weld flaw焊接缺陷weld flush焊缝隆起weld fumes焊接烟尘weld gage焊缝检查规; 焊缝卡规weld gauge焊缝量规weld heat input焊接热输入; 焊接线能量weld holder焊接夹持架; 焊接架weld inspection焊缝质量检验; 焊接检查weld interface焊缝界面; 焊接界面weld interval焊接时间weld is accepted焊缝合格weld jig焊接夹具weld joint焊缝weld junction熔焊线; 熔合线weld layer焊接层weld length焊缝长度weld line焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush削平补强的焊缝weld mark焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate焊接网格weld metal焊缝金属; 焊接金属weld metal buildup surface金属堆焊表面weld metal composition焊接金属组成weld metal cracking焊缝裂纹weld metal zone焊缝金属区; 焊接金属熔化区weld nugget焊点熔核weld on bottom底焊weld overlap重叠区weld pass焊接通道weld penetration焊缝熔深; 焊透深度weld period焊接时间weld pitch焊缝距weld porosity焊缝气孔weld preheating焊前预热weld preparation焊缝坡口加工weld puddle熔池weld reinforcement焊缝补强; 焊缝加强; 焊接补强 weld repairs焊接修补weld ripple焊缝波纹weld root焊件剖口; 焊接根weld root opening gap焊缝根部间隙weld root reinforcement焊缝反面加强weld rotation焊缝转角weld seam pipe焊缝管weld shape焊缝形状weld shielding焊接区保护; 焊接熔池保护weld slope焊缝倾角weld spacing焊点距; 焊缝间距weld strain焊接应变weld strength焊接强度weld surface焊缝表面weld swell焊缝隆起weld thermal cycle焊接热循环weld thickness焊缝厚度weld time焊接时间; 焊接通电时间; 接触焊通电时间 weld toxic gases焊接有害气体weld trimmer焊缝清理机weld up焊补weld wheel conditioner焊轮调节器weld width焊缝宽度weld wire包铜钢丝weld zone焊缝区; 焊接区weld-form factor焊缝形状系数weld-fusion line焊缝熔合线weld-in nozzle焊入式喷嘴weld-interval timer焊接间隔记时器weld-shrunk cylinder包扎式圆筒weld-shrunk multilayered cylinder包扎式多层圆筒; 多层包扎式圆筒weld-throat thickness depth焊缝厚度window type restraint weld cracking test窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld焊缝表面AC & D. C. arc welding machine交直流弧焊机AC arc welding交流电弧焊AC gas metal-arc welding process交流熔化极气保护焊AC gas tungsten arc welding交流钨极气保护焊AC welding set交流焊机; 交流焊接变压器AC-dc welding machine交直流两用焊机acetylene welding气焊; 乙炔焊; 乙炔焊接acetylene welding torch乙炔焊炬; 乙炔接焊吹管air-acetylene welding空气-乙炔焊接all-position welding全位置焊接alloy steel gas welding rod合金钢气焊条alternating current arc welding交流电弧焊alternating current welding machine交流电焊机aluminium alloy arc welding electrode铝合金焊条aluminothermic welding铝热焊; 铸焊angle backwards welding后倾焊angle butt welding斜口对接焊angle forwards welding前倾焊annealing welding wave退火焊波antogenous welding氧炔焊apparatus for butt welding平接压焊夹具arc braze welding电弧钎焊arc flash welding电弧闪光焊arc spot welding电铆焊arc stud welding柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding弧压反馈电弧焊arc welding电弧焊; 电弧焊接; 弧焊arc welding electrode电弧焊条arc welding generator电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation自激弧焊发电机; 他激电焊发电机arc welding generator with self-excitation自激电焊发电机arc welding machine弧焊机; 电焊机; 电弧焊机arc welding mask电弧焊遮罩arc welding process电弧焊接工艺过程arc welding rectifier弧焊整流器arc welding robot弧焊机器人arc welding set电弧焊机组arc welding transformer弧焊变压器arc-welding electrode电弧焊用焊条arc-welding plant电焊厂arcogen welding电弧氧乙炔焊argon (shielded) arc welding氩弧焊接argon tungsten-arc welding钨极氩弧焊argon-arc welding氩弧焊argonaut welding自动氩弧焊atomic H welding氢原子焊atomic hydrogen welding原子氢焊atomic-hydrogen welding原子氢焊接austenite welding不锈钢焊接autogenous pressure welding自动压合热焊autogenous welding气焊automatic arc welding head自动电弧焊接机头automatic arc welding machine自动电焊机; 自动弧焊机automatic drying line for welding electrode电焊条自动烘焙线automatic slag pool welding自动电渣焊automatic spot welding自动点焊automatic submerged arc welding自动埋弧焊automatic submerged slag welding of rail钢轨自动埋弧电弧焊automatic submerged-arc welding machine埋弧自动焊机automatic transverse welding横向自动焊automatic welding自动焊; 自动焊接automatic welding head自动焊头automatic welding machine自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process自动焊接工艺规程automation of welding焊接自动化back hand welding后退焊; 反手焊接back step welding反手焊接back ward welding反手焊接back welding底焊; 退焊法back-step welding分段退焊法backhand welding逆向焊; 右焊法; 后焊法; 向后焊backing welding打底焊backstep welding分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊 backstep welding sequence分段退焊次序backward welding后倾焊; 后退焊; 向右焊balanced welding对称焊bare welding rod光焊条bare wire arc welding光焊丝电弧焊bead welding窄焊道焊接bench arc welding machine台式弧焊机bevel welding斜角焊blacksmith welding锻工焊接; 锻焊block sequence welding分段多层焊; 分段连续焊接block welding块焊接block welding sequence分段多层焊body welding machine罐身焊接机both sides welding双面焊接brass welding rod黄铜焊条braze welding钎焊; 钎焊接; 钎接; 铜焊braze-welding钎接焊bridge spot welding带接合板点焊; 单面衬垫点焊; 单面搭板点焊bridge welding桥接焊; 盖板焊brize welding硬焊build (built) up welding堆焊build-up welding堆焊building-up by welding堆焊butt resistance welding电阻对焊; 对接电阻焊butt seam welding对接滚焊butt seam welding machine对接缝焊机butt welding对接焊; 平对焊butt welding machine对接焊机butt welding process对接焊法butt-welding对接焊butt-welding machine对焊机capability of welding vertically upwards直上焊接能力capacitor-discharge welding电容放电焊接carbon arc welding碳弧焊; 碳极弧焊carbon in materials for welding焊接用材料中的碳carbon-dioxide arc welding二氧化碳保护焊carriage of automatic welding machine自动焊机走架cascade welding阶梯式焊; 山形多层焊cascade welding sequence串级叠置法cast welding铸焊cement-welding金属陶瓷焊接centralized installation of welding machine多站焊接chain intermittent fillet welding并列断续角焊缝; 链式断续角焊chemical welding化学焊circular seam welding环缝对接焊circular seam-welding machine环形滚焊机cleaning before welding焊接前的清理cleaning of welding deposits焊接沉积的清理closed butt gas pressure welding闭式加压气焊cold welding冷焊; 冷压焊cold-pressure welding冷压焊combined cutting and welding torch焊割两用炬combined cutting and-welding blow-pipe焊割两用炬combined thermit welding加压铸焊complete penetraction and fusion in welding全焊透condenser (discharge) spot-welding machine电容器放电点焊机 condenser discharge spot welding电容储能点焊; 电容贮能点焊constant current welding machine恒流电焊机constant energy welding machine恒功率电焊机constant voltage welding machine恒压电焊机constant-current arc welding power source垂降特性弧焊电源constant-current welding source恒流式焊接电源constant-power welding source恒功率式焊接电源constant-pressure pressure welding恒压压力焊constant-temperature pressure welding恒温压力焊constant-voltage welding machine恒电压焊机constant-voltage welding source恒压式焊接电源; 平特性焊接电源 consumable electrode welding熔化极电弧焊consumable guide electroslag welding自耗定向电渣焊contact welding接触焊continuous feed welding连续送丝电弧焊continuous welding连续焊; 连续焊接contour welding绕焊controlled arc welding可控电弧焊接controlled atmosohere arc welding充气室电弧焊controlled atmospere arc welding充气式电弧焊controlled tungsten-arc welding自动控制弧长的钨极电弧焊controlled-transfer welding可控过渡电弧焊convex fillet welding凸面角焊缝copper arc welding electrode铜焊条copper welding rod铜焊条copper-alloy arc welding electrode铜合金焊条copper-aluminium welding rod铜铝焊条copper-nickel welding rod铜镍焊条copper-silicon welding rod铜硅焊条copper-tin welding rod铜锡焊条copper-zinc welding rod铜锌焊条core welding-wire焊芯core wire for welding rod焊条芯线corrosion due to welding焊接腐蚀cosmetic welding盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machine二氧化碳弧焊机cracking test for automatic welding自动焊抗裂试验crankshaft flashbutt welding曲轴电阻弧花压焊cross welding横向焊缝cyc-arc welding圆环电弧焊deck welding重力焊deep fillet welding深角焊deep penetration welding深熔焊deep penetration welding electrode深熔焊条deep welding深焊die welding模焊; 冲模堆焊diesel engine driven DC arc welding machine柴油机驱动直流弧焊机 differential-excited welding generator差激电焊发电机diffusion welding扩散焊接direct spot welding双面点焊direct welding双面点焊direction of welding焊接方位; 焊接方向discontinuous welding断续焊dot welding点焊double carbon-arc welding间接碳弧焊double side welding双面焊接down-hand welding俯焊downhand welding平焊downward welding in the inclined position下坡焊downward welding in the vertical position向下立焊dual-arc welding双弧焊edge seam welding端面接头滚焊edge welding边缘焊接edgewise welding沿边焊接electric and pressure welding电压力焊接electric arc spot welding电弧点焊electric arc welding generators电弧焊接发电机electric arc welding machine电弧焊机electric butt welding电阻接触焊electric resistance welding电阻焊接; 热电阻焊electric slag welding电渣焊electric spot welding电点焊electric welding电焊electric welding cast copper solder铸铜电焊条electric welding equipment电焊设备electric welding generator电焊发电机electric welding hammer电焊锤electric welding machine电焊机electric welding plant电焊厂electric welding pliers电焊钳electric welding rod电焊条electric welding strip电焊片electric-arc welding电弧焊electric-resistance seam-welding电阻缝焊electric-resistance seam-welding machine电阻缝焊机electrical arc welding电弧焊接electrical resistance welding tube电阻焊接管electrically heated welding torch电热焊枪electro-beam welding电子束焊接electro-gas (enclosed) welding气电立焊electro-slag welding电磁渣焊; 电渣焊electro-slag welding with plate electrode板极电渣焊electro-welding电焊electrode for arc welding电焊条; 电弧焊条electrode for vertical down welding向下立焊条electrode of vertical down welding立向下焊条electrode welding电弧焊electrogas welding气电焊; 电气焊electromagnetic percussive welding电磁冲击焊electromagnetic stored energy welding电磁储能焊electron beam welding电子束焊; 电子束焊接electron beam welding machine电子束焊接机electron-beam welding电子束焊接electron-beam welding machine电子束焊机electron-bombardment welding真空电子束焊electrons leaves welding电子束焊接electropercussive welding电冲击焊; 冲击焊; 储能焊electroslag welding电渣焊; 电阻焊electroslag welding machine电渣焊机electroslag welding with consumable nozzle熔嘴电渣焊electroslag welding with wire electrode丝极电渣焊electrostatic (percussive) welding电能储能焊接electrostatic percussing welding静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding静电冲击焊; 静电冲击焊enclosed welding强制成形焊接energy storage welding贮能焊; 储能焊; 脉冲焊接erecting welding装配焊接erection welding安装焊接eutectic welding低温焊exothermic welding铝热焊expanding or welding of tube with tubesheet管子与管板的胀接或焊接 explosive welding (EW)爆炸焊eyelet welding孔焊; 小孔熔焊faster welding快速焊接feed rate of welding wire焊丝送进速度field of welding temperature焊接温度场field welding现场焊接; 工地焊接Filler arc welding菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position船形角焊fillet welding in the flat position船形焊fillet welding in the horizontal position横角焊fillet welding in the vertical position立角焊fine welding精密焊接fine wire welding细丝焊fire cracker welding躺焊fire welding锻焊; 锻接fixed welding machine固定式焊机fixed-position welding定位焊接flame welding熔气焊flare welding喇叭形坡口焊接flash butt welding闪光对焊; 闪光对接焊flash welding闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊 flash-butt welding电阻闪光焊接flashover welding闪光焊flat position welding平焊; 顶面平卧焊flat position welding of fillet weld角焊缝平焊; 船形角焊flat welding平卧焊flexible welding rod软焊条flexible wire for electric welding电焊软线flow welding流注焊接; 浇焊fluid welding流焊flux-cored welding包芯焊条焊接fly-wheel type friction welding贮能摩擦焊; 储能摩擦焊flywheel friction welding惯性摩擦焊forehand welding向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding锻焊; 锻接焊forward welding正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊 friction welding摩擦焊; 摩擦焊接friction welding machine摩擦焊接机frontal fillet welding正面角焊full automatic welding全自动焊full-automatic arc welding全自动电弧焊full-fillet welding满角焊full-fusion thermit welding热剂铸焊full-fusion welding全熔合焊full-length welding满焊fusion pressure welding熔化压接fusion thermit welding热剂熔焊; 熔化铝热焊fusion type plasma arc welding熔透型等离子弧焊fusion type welding熔透型焊接法fusion welding熔焊接fusion welding metal熔焊金属gas carbon-arc welding气保护碳弧焊gas electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊gas metal-arc welding气保护金属极电弧焊gas shield welding气体保护弧焊gas shielded arc welding气体保护电弧焊; 气体保护焊gas shielded arc welding machine气保护弧焊机gas shielded arc-welding machine气体保护弧焊机gas shielded magnetic flux arc welding磁性焊剂气体保护电弧焊 gas shielded metal-arc welding气体保护金属弧焊gas shielded welding气体保护焊gas torch welding气炬焊gas tungsten arc welding气体保护钨极电弧焊gas tungsten-arc welding气保护钨极电弧焊gas tungstun arc welding钨极气体保护焊gas welding气焊; 乙炔焊gas welding device气焊设备gas welding equipment气焊设备gas welding machine气焊机gas welding outfit气焊机gas welding rod气焊焊丝gas welding rubber hose气焊橡胶管gas welding technique气焊工艺gas welding torch butt气焊进气硬管gas welding tube mill瓦斯焊接机gas welding work气焊工作gas-arc welding气电焊; 气体保护电弧焊gas-arc welding gun气电焊焊嘴gas-press welding气压焊gas-pressure welding machine气压焊接机gas-shielded stud welding气保护柱钉焊接girth welding环缝横向焊接gravity type arc welding重力焊gravity type welding倚焊gravity welding重力焊; 重力式电弧焊groove welding槽焊; 坡口焊; 开槽焊guided automatic welding导向自动焊接gun welding machine手提式点焊机; 点焊枪hafnium welding wire铪焊丝hammer welding锻焊; 锻接; 锤焊hammered resistance welding锤锻电阻焊; 电阻加热锻焊hand welding holdet手焊焊把hard-welding硬质合金熔焊headless bolt for welding焊接单头螺栓heat-welding adhesive热熔性胶粘剂heated-tool welding热烙铁焊接heavy welding大断面焊接heavy welding electrode粗电焊条heliarc welding氦电弧焊Heliarc welding氦弧焊法helium arc welding氦弧焊HF welding magnetic bar高频焊接磁棒hidden arc welding埋弧焊; 潜弧焊high current arc welding大电流弧焊high frequency AC welding machine高频交流电焊机high frequency dielectric welding高频介电焊high frequency induction welding高频感应焊high frequency welding高频焊接high grade energy welding高能焊high tensile electric welding rod高强焊条high-current plasma arc welding大电流等离子弧焊high-frequency induction welding高频感应焊接; 高频焊接high-frequency resistance welding高频接触焊high-frequency resistance welding (HFRW)高频电阻焊high-frequency welding高频电焊highspeed welding快速焊接horizontal fillet welding横角焊; 水平角焊horizontal position welding水平焊接; 横焊horizontal welding横焊; 水平焊horizontal-position welding水平位置焊接horizontal-rolledposition welding水平转动焊接; 滚动水平焊hot jet welding热风焊接hot press welding热压焊接hot pressure welding预热压力焊hot welding热焊hot wire welding热丝焊hot(-)gas welding热气焊接hot-gas welding热风焊接; 热空气焊接hot-pressure welding热压焊; 热压焊接hydrogen-welding氢焊impact spot welding冲击点焊法impregnated-tape metal-arc welding浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机 impulse current seam welding machine脉冲电流缝焊机impulse current semiautomatic butt welding machine脉冲电流半自动对焊机impulse electromagnetic automatic welding machine电磁脉冲自动焊机impulse plasma welding machine脉冲等离子焊机impulse welding脉冲焊; 脉冲焊接impulsed spot welding脉冲点焊inclined position welding倾斜焊indirect (spot) welding单面点焊indirect welding单面点焊induction welding感应焊; 感应焊接; 感应熔焊inert gas arc spot welding惰性气体电弧点焊inert gas arc welding惰性气体电弧焊inert gas spot welding惰性气体保护电弧点焊inert gas welding惰性气体焊接法inert-gas (inert gas) arc welding惰性气体保护焊inertia welding惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding惯性焊接infrared welding红外线焊接intermediate current plasma arc welding中电流等离子弧焊intermittent fillet welding断续角焊intermittent point welding断续点焊intermittent welding断续焊International Institute of welding (IIW)国际焊接学会inverted welding仰焊joint welding搭焊jump welding丁字形焊keyhole-mode welding小孔型等离子弧焊; 穿透型焊接法lap fillet welding搭角焊; 搭接角焊lap resistance welding搭接电阻焊lap seam welding搭接缝焊; 搭接焊lap welding搭焊; 搭接焊laser welding激光焊接laser welding chamber激光焊接室laser welding head激光焊接头laser welding machine for orthodontics激光口腔矫形焊接机laser welding system激光焊接系统laser-beam welding machine激光焊接机laser-welding machine激光焊接器lead welding铅焊lefthand welding左焊法leftward welding左向焊法lever gun welding head杠杆式点焊钳light beam welding machine光束焊机light continuous welding轻连续焊接light gauge welding薄板焊接light ray welding光束焊接light welding轻焊接Linde welding林德钢管对焊法line welding直线焊缝焊接liquid metal welding浇注补焊longitudinal resistance seam welding纵向电阻缝焊longitudinal seam welding纵缝焊接; 纵向缝焊longitudinal welding纵缝焊接; 纵向焊接low carbon steel welding electrode低碳钢电焊条low carbon welding wires低碳焊接线材low idle voltage arc-welding power supply低空载电压的弧焊电源 low temperature welding低温焊接low-alloy steel covered arc welding electrode低合金钢焊条low-current plasma arc welding小电流等离子弧焊low-hydrogen welding electrode低氢型电焊条low-temperature welding低温焊接lowest permissible temperature for welding焊接允许的最低温度 machine for magnetic welding磁力焊接机machine welding机器焊接machine welding torch机械焊接吹管magnetic discharge welding电磁储能焊; 电磁焊magnetic flux arc welding磁性焊剂电弧焊magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊 magnetic force welding machine磁力焊接机magnetic-force welding磁力焊接法manual arc welding手工电弧堆焊manual electic arc pile up welding手工电弧堆焊manual electric arc welding手工电弧堆焊manual electro-slag welding手工电渣焊manual gas welding手工气焊manual metal-arc welding手弧焊manual TIG welding手工钨极惰性气体保护焊manual welding手工焊接; 人工焊接manual welding machine手工焊机manually coating welding electrode手涂焊条mash seam welding滚压电阻缝焊mash stitch welding多针缝式焊接mask welding电焊眼罩match assemble welding装架焊接metal arc welding金属电弧焊metal buried welding埋渣焊metal inert gas arc welding (MIG)惰性气体金属电弧焊metal inert-gas arc welding金属极惰性气体保护焊metal inertia gas welding金属焊条惰性气体保护焊; 熔化极惰性气体保护焊metal rectifier welding set整流焊机metal-arc gas-shielded welding气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW)金属极气保护焊metal-arc welding金属极电弧焊micro resistance welding显微电阻焊micro-gap welding微间隙焊接micro-plasma arc welding微束等离子弧焊micro-welding微型焊接; 显微焊接microgap welding微隙间隙焊Miebach high efficiency flash welding machine米巴赫高效闪光对焊机 mild steel arc welding electrode低碳钢焊条mild steel welding rod低碳钢焊丝miter welding斜接头焊接mixed gas arc welding混合气体保护电弧焊molten bath arc welding熔池电弧焊molten-bath arc welding熔池焊motor driven welding machine电动焊机; 电动机拖动式焊机motor-driven welding machine电动旋转式焊机motor-generator welding unit电动直流发电焊接设备multi-head automatic arc-welding machine多头自动电弧焊机multi-head automatic welding machine多头自动焊机multi-operator welding set多站电焊机multi-pass (multiple pass) welding多道焊multiarc welding多弧焊multihead automatic arc welding machine多弧自动电焊机multilayer welding多层焊multioperator welding generator多工位焊接发电机multioperator welding machine多站电焊机; 多站焊机multioperator welding set多站焊机multipass welding多道焊接multiple arc welding多弧焊multiple operator arc welding machine复式弧焊机multiple projection welding多点凸焊multiple resistance welding多点电阻焊接; 复式电阻焊multiple spot welding多点点焊multiple spot welding machine多点点焊机multiple-arc welding plant多弧焊接机multiple-electrode spot welding machine多极点焊机multiple-electrode welding多焊条焊接。
焊接专业焊接英汉词典
焊接专业焊接英汉词典actual weld-throat thick-ness焊缝厚度all-around weld整周焊缝all-around weld (整周焊缝)环焊缝angle butt weld斜对接焊angle weld角焊appearance of weld焊缝成形arc-seam weld电弧缝焊arc-spot weld电弧点焊arc-weld电弧焊aspect ratio of weld焊缝成形系数at weld edge在焊缝边上attachment weld连接焊缝automatic spot weld自动点焊法automatic weld自动焊接axis of a weld焊缝中心线; 焊接轴线axis of weld焊缝轴线; 焊接轴线back of weld焊缝背面backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝bare metal arc weld裸焊条电弧焊bead weld珠焊; 堆焊bead-on-plate weld堆焊焊缝beading weld凸焊beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊bond weld钢轨接头焊接bridge seam weld桥缝焊接; 桥线焊brize weld硬焊butt weld对接焊缝butt weld ends对头焊接端butt-weld碰焊; 平式焊接; 对头焊接butt-weld in the downhand position对接平焊butt-weld joint对头焊接butt-weld pipe mill对焊管轧机button spot weld按电钮点焊cap weld最后焊层; 盖面焊缝carbon content of weld materials焊接材料的碳含量 cast-weld construction铸焊结构caulk weld填缝焊caulking weld密实焊缝chain intermittent fillet weld链式分段角焊; 并列间断角焊缝 chain intermittent weld并列焊接circular weld环形焊缝circumferential weld环缝; 环焊缝cleft weld裂口焊closed weld底边无缝焊; 无间隙焊缝closed-chamber fusion weld闭室熔焊cluster weld丛聚焊缝coil weld卷板对接焊; 卷板对接焊; 板卷焊cold weld冷压接commutator-controlled weld换向控制焊接complete penetration butt weld贯穿对焊composite weld紧密焊缝; 强度密封焊缝concave filled weld凹形角焊缝concave filler weld凹角焊concave fillet weld凹面填角焊concave weld凹焊缝; 凹面焊; 凹形焊缝; 轻型焊connective weld联系焊缝continuous butt-weld mill连续式炉焊管机组continuous fillet weld连续(填)角焊缝; 连续角焊缝; 连续贴角焊 continuous weld连续焊缝continuous weld process连续式炉焊管法contour weld特形焊接convex fillet weld凸角焊缝; 凸形角焊缝convex weld凸焊缝; 凸形焊缝copper weld wire包铜钢丝corner flange weld单卷边角焊缝corner weld角焊corner-flange weld卷边角焊缝; 卷边角焊缝crack of weld焊部裂纹cross weld十字交叉焊缝; 横向焊缝cross-wire weld十字焊crotch weld楔接锻接; 楔接焊接cup weld带盖板焊缝depth of weld焊接深度dissimilar weld metal不同的焊接金属; 不同金属的焊接distance between the toes of a weld焊缝宽度double groove weld双面坡口焊缝double-bevel groove weld双斜边坡口焊缝; 双斜坡口焊double-flanged butt weld双弯边对接焊缝double-V groove weld双斜边坡口焊缝; 双斜坡口焊downhand weld平焊缝duplex spot weld双点点焊接头edge joint weld边缘焊edge weld端接焊; 端接焊缝; 端面焊缝; 对边焊electric resistance weld mill电阻焊管机electric weld-pipe mill电焊管机electric-weld pipe mill电焊管机emporary weld临时点定焊缝excess weld metal焊缝补强金属; 补强; 补强焊料; 补强金属 excess weld metal(焊缝的)余高explosive weld爆炸焊接face of weld焊缝表面; 焊接面fibrous weld纤维状焊缝field weld现场焊接filler weld填角焊缝fillet weld角焊缝; 填角焊; 贴角焊fillet weld in normal shear (搭接接头的)正面角焊缝fillet weld in parallel shear侧面角焊缝; 侧面填角焊fillet weld in the flat position角接平焊; 水平角焊缝fillet weld in the horizontal position横向角焊缝fillet weld size焊角尺寸; 填角焊缝尺寸flame weld火焰焊接flange weld卷边焊缝; 卷边焊缝flange-to-web weld卷边焊缝; 卷边焊缝flanged butt weld弯边对接焊flanged edge weld卷边焊; 卷边焊flash butt weld闪光焊flash weld闪速对焊flat faced fillet weld平顶角焊缝焊接flat fillet weld平角焊ing of fillet weld角焊缝平焊; 船形角焊flush fillet weld平角焊flush weld削平补强的焊缝; 平焊接; 无加强高的焊缝forge weld锻焊焊缝forged weld (焊后锻压的)锻压焊缝form factor of the weld焊缝成形系数formation of weld焊缝成形front fillet weld正侧面填角焊缝; 正面填角焊front(al) fillet weld正面角焊缝full fillet weld满角焊缝; 全角焊full penetration butt weld满对接焊full weld满焊full-fillet weld满角焊full-sized weld全尺寸焊缝full-strength weld (与母材等强)等强焊缝gap weld特殊点焊; 双极单点焊gas-pressure weld气压焊girth weld环形焊缝gravity weld倚焊groove weld坡口焊; 坡口焊缝; 有坡口焊缝; 凹槽焊groove-weld joint有坡口焊接接头hammer weld锻焊hand weld手焊焊缝height of reinforcement of weld加强焊缝高度helical-weld pipe螺旋焊管high performance weld flux高性能焊剂horizontal fillet weld横向角缝焊接horizontal weld横向焊缝horizontal-vertical fillet weld横向垂直角焊缝hot weld encapsulation热焊封袋hydraulic automatic weld液压自动焊接hydraulic weld process液压焊接法inclined weld斜焊inconel weld单面焊缝incorrect weld profile焊缝形状不对incorrect weld size焊缝尺寸不对induction weld mill感应焊管机inside corner weld内角焊接inside fillet weld内角焊接inside weld内焊缝insufficient or excess reinforcement of weld加强焊缝不足或过量 intermittent fillet weld间断角缝焊接; 断续角焊缝intermittent weld断续焊; 断续焊缝jam weld对接焊; 对头焊接lap fillet weld搭接角焊缝laser (beam) weld (ing)激光焊lateral weld侧焊; 侧面焊缝leg of a fillet weld角焊缝; 角焊缝焊脚leg of fillet weld圆角焊肉厚length of weld焊缝长度light closing weld轻连续焊接light fillet weld轻型填角焊; 小填角焊light weld轻焊缝Lincoln weld埋弧自动焊longitudinal fillet weld纵向角焊longitudinal weld纵向焊缝longitudinal weld (焊接用语)纵缝loose weld脱焊main weld主焊缝mash seam weld压薄缝焊; 滚压焊mash weld点焊; 点压焊melt thru weld熔透焊缝melt-through weld透溶焊melten weld pool焊接熔池melting through weld熔透焊缝miter weld平顶角焊缝; 斜接角焊缝molten weld metal熔融焊接金属mulitple impulse weld多脉冲焊缝multilayer weld多层焊缝multipass weld多道焊缝multiple arc weld多弧焊缝multiple-electrode submerged arc weld多电极埋弧焊 multiple-pass weld多道焊缝; 多路焊接multirun weld多道焊缝nonpressure thermit weld不加压热剂焊缝normal weld正常焊接oblique fillet weld斜交角焊缝; 斜角焊接one-pass weld单层焊缝open butt weld开口对接焊open weld留间隙焊缝; 空隙焊outside weld外焊缝over weld过焊overhead fillet weld仰焊角焊缝overhead weld仰焊oversize weld超尺寸焊缝oxygen weld氧气焊接parallel-arc weld并列弧焊patch weld补焊; 补孔焊缝Peltier's cross weld珀耳帖交叉焊接penetration weld熔透焊缝percussion weld冲击焊缝; 冲击焊接periphera weld环形焊缝pitch of weld焊缝接距; 焊线距plain butt weld无坡口对接焊; 平头对接焊缝plasma-arc weld等离子弧焊接plug weld塞焊焊缝point of weld焊接点point weld点焊poor weld劣质焊缝; 有缺陷的焊缝porous weld多孔焊缝; 疏松焊缝positioned weld平位焊缝; 暂焊post weld annealed (PWA)焊后退火poured weld铸焊焊缝powder weld process粉末焊接法practice weld试验焊缝pressure weld压焊pressure-controlled weld压力控制焊接pressure-tight weld气密焊; 密封焊道principal weld主要焊缝profile of fillet weld填角焊缝轮廓progress of weld焊向projection weld凸焊; 凸焊焊缝projection weld machine凸点电阻焊机pulsating weld脉冲接触焊push weld挤焊quilting weld钉焊reinforced butt weld补强的对接焊缝; 补强式对接焊缝 reinforced weld加强焊接reinforcement of weld焊缝加厚; 补强金属; 加强焊缝 resistance weld mill电阻焊管机resistance weld pipe电阻焊管resonance butt weld谐振式对接焊restarting a weld再引弧ripple weld鳞状焊缝rivet weld电铆; 电铆焊缝root face of weld焊缝根部钝边root gap of weld焊缝根部间隙root of weld焊缝根部; 焊根root opening of weld焊缝根部间隙root radius of weld焊缝坡口根部半径sagged weld下垂焊缝scarf weld楔口焊接seal weld填焊; 致密焊缝; 密封焊; 密封焊道; 密封焊缝 sealing weld封焊seam weld滚焊semi-automatic arc weld半自动电弧焊sequence weld timer序列焊接时间调节器shallow weld浅焊shop weld工厂焊接shot weld点焊shoulder of weld焊缝根部钝边side fillet weld侧面角焊缝; 侧面填角焊缝; 侧面贴角焊 side lap weld侧边搭接焊; 弯边搭焊缝side weld侧焊缝; 边焊single lap weld单搭接焊single strap butt weld单面盖板对接焊single-bevel groove weld单斜角槽焊single-fillet weld单边角接焊缝single-pass weld单道焊site weld现场焊接; 安装焊; 安装焊接size of a fillet weld焊角尺寸size of weld焊件的大小; 焊区尺寸skew weld斜焊skin weld表面焊接sleeve weld套筒焊接slip-weld hanger卡瓦焊接套管挂slot weld槽塞焊; 长孔焊; 开槽搭焊缝; 切口焊缝ing slotted weld槽焊slotted lap weld切口搭接焊smooth fillet weld平填角焊缝socket weld ends承插焊接端soft-weld铜镍焊条合金solvent weld溶剂焊接space of intermittent weld断续焊缝间距; 断续焊间距spiral weld螺旋形焊缝spiral weld-pipe mill螺旋焊管机spot weld焊点spot weld bonding胶结点焊spot weld nugget点焊熔核spreading weld宽缝焊接; 加宽的焊缝square butt weld平头对接焊缝square groove weld无坡口槽焊staggered intermittent fillet weld (ing)交错断续角焊staggered intermittent weld交错断续焊缝; 交错间断焊staggered plug weld交错塞焊standard reinforced fillet weld标准加强角焊缝stick-out weld未熔合点焊接头stitch-and-seam weld点线焊straight butt weld无坡口对接接头strapped weld搭板对接焊缝strength weld受载焊缝; 强固焊接; 承载焊缝; 高强度焊接structural weld强固焊缝surface of weld焊缝表面surface weld表面焊缝surface weld metal buildup表面焊缝金属的形成synthetic apparatus for weld thermal cycle焊接热循环模拟装置 T weld丁字接头焊缝T-filled weld丁字形角焊T-fillet weld丁字接头角焊缝tack weld定位焊点; 定位焊缝; 临时点焊; 预焊; 平头焊接(welding)定位焊tandem arc weld前后弧焊temporary weld临时点固焊缝tension weld受拉焊缝test weld试焊throat depth (thickness) of fillet weld角焊缝厚度 throat of fillet weld凹角焊喉; 填角焊缝喉长throat of weld凹角焊喉tight weld密封焊接; 致密焊缝tight-strong weld密实强固焊缝toe of the weld焊缝边界toe of weld焊趾toe weld趾部焊缝torch weld气焊焊缝total amount of weld fumes焊接发尘量transverse fillet weld横向角焊缝; 正面角焊transverse weld横向焊缝trial weld试验焊接undercut weld底切焊接undressed weld (增加焊缝)未加工焊缝unequal fillet weld焊脚不等的角焊缝unfitness of butt weld焊缝对口错边量union-melt weld埋弧焊unload weld非承载焊缝unspaced butted weld无间隙对接焊缝upgrading of boiler weld锅炉焊缝加强vertical fillet weld立焊角焊缝vertical weld立焊weak weld不强固焊缝weaving weld横向摆动焊缝weld焊; 焊接的; 补焊weld all around围焊weld appearance焊缝外观weld assembly焊接组件weld back-up焊缝背垫weld backing焊缝衬垫weld bead焊缝; 熔敷焊道weld bead height焊缝高度weld beading焊瘤weld bond熔合线weld bridge seam搭桥焊缝; 桥接焊缝weld cap焊帽weld center line焊缝中心线weld collar加强焊缝焊瘤weld crack焊接裂纹weld crater熔池weld crosswise交叉焊接weld decay焊缝腐蚀; 焊接接头晶间腐蚀; 焊接侵蚀; 焊接区晶间腐蚀 weld decay (焊接后)敏化区腐蚀weld defect焊接缺陷weld delay time焊接延迟时间weld deposit堆焊weld deposits cleaning焊接熔敷金属清理weld edge焊缝边缘; 焊缝表面边缘weld edgewise沿边焊接weld flange connection焊接法兰连接weld flash焊瘤weld flaw焊接缺陷weld flush焊缝隆起weld fumes焊接烟尘weld gage焊缝检查规; 焊缝卡规weld gauge焊缝量规weld heat input焊接热输入; 焊接线能量weld holder焊接夹持架; 焊接架weld inspection焊缝质量检验; 焊接检查weld interface焊缝界面; 焊接界面weld interval焊接时间weld is accepted焊缝合格weld jig焊接夹具weld joint焊缝weld junction熔焊线; 熔合线weld layer焊接层weld length焊缝长度weld line焊缝线; 焊缝轴线; 焊接线; 焊线weld machined flush削平补强的焊缝weld mark焊缝符号; 焊缝记号; 焊接痕; 熔缝weld mesh crate焊接网格weld metal焊缝金属; 焊接金属weld metal buildup surface金属堆焊表面weld metal composition焊接金属组成weld metal cracking焊缝裂纹weld metal zone焊缝金属区; 焊接金属熔化区weld nugget焊点熔核weld on bottom底焊weld overlap重叠区weld pass焊接通道weld penetration焊缝熔深; 焊透深度weld period焊接时间weld pitch焊缝距weld porosity焊缝气孔weld preheating焊前预热weld preparation焊缝坡口加工weld puddle熔池weld reinforcement焊缝补强; 焊缝加强; 焊接补强weld repairs焊接修补weld ripple焊缝波纹weld root焊件剖口; 焊接根weld root opening gap焊缝根部间隙weld root reinforcement焊缝反面加强weld rotation焊缝转角weld seam pipe焊缝管weld shape焊缝形状weld shielding焊接区保护; 焊接熔池保护weld slope焊缝倾角weld spacing焊点距; 焊缝间距weld strain焊接应变weld strength焊接强度weld surface焊缝表面weld swell焊缝隆起weld thermal cycle焊接热循环weld thickness焊缝厚度weld time焊接时间; 焊接通电时间; 接触焊通电时间weld toxic gases焊接有害气体weld trimmer焊缝清理机weld up焊补weld wheel conditioner焊轮调节器weld width焊缝宽度weld wire包铜钢丝weld zone焊缝区; 焊接区weld-form factor焊缝形状系数weld-fusion line焊缝熔合线weld-in nozzle焊入式喷嘴weld-interval timer焊接间隔记时器weld-shrunk cylinder包扎式圆筒weld-shrunk multilayered cylinder包扎式多层圆筒; 多层包扎式圆筒weld-throat thickness depth焊缝厚度window type restraint weld cracking test窗口拘束焊缝抗裂试验; 窗形拘束抗裂试验zigzag intermittent fillet weld锯齿形断续角焊缝; 锯齿形断续角焊缝zone of weld焊缝表面AC & D. C. arc welding machine交直流弧焊机AC arc welding交流电弧焊AC gas metal-arc welding process交流熔化极气保护焊AC gas tungsten arc welding交流钨极气保护焊AC welding set交流焊机; 交流焊接变压器AC-dc welding machine交直流两用焊机acetylene welding气焊; 乙炔焊; 乙炔焊接acetylene welding torch乙炔焊炬; 乙炔接焊吹管air-acetylene welding空气-乙炔焊接all-position welding全位置焊接alloy steel gas welding rod合金钢气焊条alternating current arc welding交流电弧焊alternating current welding machine交流电焊机aluminium alloy arc welding electrode铝合金焊条aluminothermic welding铝热焊; 铸焊angle backwards welding后倾焊angle butt welding斜口对接焊angle forwards welding前倾焊annealing welding wave退火焊波antogenous welding氧炔焊apparatus for butt welding平接压焊夹具arc braze welding电弧钎焊arc flash welding电弧闪光焊arc spot welding电铆焊arc stud welding柱钉电弧焊; 螺柱电弧焊arc voltage feedback controlling arc welding弧压反馈电弧焊arc welding电弧焊; 电弧焊接; 弧焊arc welding electrode电弧焊条arc welding generator电弧焊接用发电机; 弧焊发电机arc welding generator with independent excitation自激弧焊发电机; 他激电焊发电机arc welding generator with self-excitation自激电焊发电机arc welding machine弧焊机; 电焊机; 电弧焊机arc welding mask电弧焊遮罩arc welding process电弧焊接工艺过程arc welding rectifier弧焊整流器arc welding robot弧焊机器人arc welding set电弧焊机组arc welding transformer弧焊变压器arc-welding electrode电弧焊用焊条arc-welding plant电焊厂arcogen welding电弧氧乙炔焊argon (shielded) arc welding氩弧焊接argon tungsten-arc welding钨极氩弧焊argon-arc welding氩弧焊argonaut welding自动氩弧焊atomic H welding氢原子焊atomic hydrogen welding原子氢焊atomic-hydrogen welding原子氢焊接austenite welding不锈钢焊接autogenous pressure welding自动压合热焊autogenous welding气焊automatic arc welding head自动电弧焊接机头automatic arc welding machine自动电焊机; 自动弧焊机automatic drying line for welding electrode电焊条自动烘焙线automatic slag pool welding自动电渣焊automatic spot welding自动点焊automatic submerged arc welding自动埋弧焊automatic submerged slag welding of rail钢轨自动埋弧电弧焊automatic submerged-arc welding machine埋弧自动焊机automatic transverse welding横向自动焊automatic welding自动焊; 自动焊接automatic welding head自动焊头automatic welding machine自动焊接机automatic welding of circumferential seams环缝自动焊automatic welding process自动焊接工艺规程automation of welding焊接自动化back hand welding后退焊; 反手焊接back step welding反手焊接back ward welding反手焊接back welding底焊; 退焊法back-step welding分段退焊法backhand welding逆向焊; 右焊法; 后焊法; 向后焊backing welding打底焊backstep welding分段逆焊; 分段退焊; 反向焊; 逐步退焊法; 逆向焊 backstep welding sequence分段退焊次序backward welding后倾焊; 后退焊; 向右焊balanced welding对称焊bare welding rod光焊条bare wire arc welding光焊丝电弧焊bead welding窄焊道焊接bench arc welding machine台式弧焊机bevel welding斜角焊blacksmith welding锻工焊接; 锻焊block sequence welding分段多层焊; 分段连续焊接block welding块焊接block welding sequence分段多层焊body welding machine罐身焊接机both sides welding双面焊接brass welding rod黄铜焊条braze welding钎焊; 钎焊接; 钎接; 铜焊braze-welding钎接焊bridge spot welding带接合板点焊; 单面衬垫点焊; 单面搭板点焊 bridge welding桥接焊; 盖板焊brize welding硬焊build (built) up welding堆焊build-up welding堆焊building-up by welding堆焊butt resistance welding电阻对焊; 对接电阻焊butt seam welding对接滚焊butt seam welding machine对接缝焊机butt welding对接焊; 平对焊butt welding machine对接焊机butt welding process对接焊法butt-welding对接焊butt-welding machine对焊机capability of welding vertically upwards直上焊接能力capacitor-discharge welding电容放电焊接carbon arc welding碳弧焊; 碳极弧焊carbon in materials for welding焊接用材料中的碳carbon-dioxide arc welding二氧化碳保护焊carriage of automatic welding machine自动焊机走架cascade welding阶梯式焊; 山形多层焊cascade welding sequence串级叠置法cast welding铸焊cement-welding金属陶瓷焊接centralized installation of welding machine多站焊接chain intermittent fillet welding并列断续角焊缝; 链式断续角焊 chemical welding化学焊circular seam welding环缝对接焊circular seam-welding machine环形滚焊机cleaning before welding焊接前的清理cleaning of welding deposits焊接沉积的清理closed butt gas pressure welding闭式加压气焊cold welding冷焊; 冷压焊cold-pressure welding冷压焊combined cutting and welding torch焊割两用炬combined cutting and-welding blow-pipe焊割两用炬combined thermit welding加压铸焊complete penetraction and fusion in welding全焊透condenser (discharge) spot-welding machine电容器放电点焊机 condenser discharge spot welding电容储能点焊; 电容贮能点焊constant current welding machine恒流电焊机constant energy welding machine恒功率电焊机constant voltage welding machine恒压电焊机constant-current arc welding power source垂降特性弧焊电源constant-current welding source恒流式焊接电源constant-power welding source恒功率式焊接电源constant-pressure pressure welding恒压压力焊constant-temperature pressure welding恒温压力焊constant-voltage welding machine恒电压焊机constant-voltage welding source恒压式焊接电源; 平特性焊接电源 consumable electrode welding熔化极电弧焊consumable guide electroslag welding自耗定向电渣焊contact welding接触焊continuous feed welding连续送丝电弧焊continuous welding连续焊; 连续焊接contour welding绕焊controlled arc welding可控电弧焊接controlled atmosohere arc welding充气室电弧焊controlled atmospere arc welding充气式电弧焊controlled tungsten-arc welding自动控制弧长的钨极电弧焊controlled-transfer welding可控过渡电弧焊convex fillet welding凸面角焊缝copper arc welding electrode铜焊条copper welding rod铜焊条copper-alloy arc welding electrode铜合金焊条copper-aluminium welding rod铜铝焊条copper-nickel welding rod铜镍焊条copper-silicon welding rod铜硅焊条copper-tin welding rod铜锡焊条copper-zinc welding rod铜锌焊条core welding-wire焊芯core wire for welding rod焊条芯线corrosion due to welding焊接腐蚀cosmetic welding盖面焊cover chain welding链节式药皮包丝焊接CO 2 arc welding machi ne二氧化碳弧焊机cracking test for automatic welding自动焊抗裂试验crankshaft flashbutt welding曲轴电阻弧花压焊cross welding横向焊缝cyc-arc welding圆环电弧焊deck welding重力焊deep fillet welding深角焊deep penetration welding深熔焊deep penetration welding electrode深熔焊条deep welding深焊die welding模焊; 冲模堆焊diesel engine driven DC arc welding machine柴油机驱动直流弧焊机 differential-excited welding generator差激电焊发电机diffusion welding扩散焊接direct spot welding双面点焊direct welding双面点焊direction of welding焊接方位; 焊接方向discontinuous welding断续焊dot welding点焊double carbon-arc welding间接碳弧焊double side welding双面焊接down-hand welding俯焊downhand welding平焊downward welding in the inclined position下坡焊downward welding in the vertical position向下立焊dual-arc welding双弧焊edge seam welding端面接头滚焊edge welding边缘焊接edgewise welding沿边焊接electric and pressure welding电压力焊接electric arc spot welding电弧点焊electric arc welding generators电弧焊接发电机electric arc welding machine电弧焊机electric butt welding电阻接触焊electric resistance welding电阻焊接; 热电阻焊electric slag welding电渣焊electric spot welding电点焊electric welding电焊electric welding cast copper solder铸铜电焊条electric welding equipment电焊设备electric welding generator电焊发电机electric welding hammer电焊锤electric welding machine电焊机electric welding plant电焊厂electric welding pliers电焊钳electric welding rod电焊条electric welding strip电焊片electric-arc welding电弧焊electric-resistance seam-welding电阻缝焊electric-resistance seam-welding machine电阻缝焊机electrical arc welding电弧焊接electrical resistance welding tube电阻焊接管electrically heated welding torch电热焊枪electro-beam welding电子束焊接electro-gas (enclosed) welding气电立焊electro-slag welding电磁渣焊; 电渣焊electro-slag welding with plate electrode板极电渣焊electro-welding电焊electrode for arc welding电焊条; 电弧焊条electrode for vertical down welding向下立焊条electrode of vertical down welding立向下焊条electrode welding电弧焊electrogas welding气电焊; 电气焊electromagnetic percussive welding电磁冲击焊electromagnetic stored energy welding电磁储能焊electron beam welding电子束焊; 电子束焊接electron beam welding machine电子束焊接机electron-beam welding电子束焊接electron-beam welding machine电子束焊机electron-bombardment welding真空电子束焊electrons leaves welding电子束焊接electropercussive welding电冲击焊; 冲击焊; 储能焊electroslag welding电渣焊; 电阻焊electroslag welding machine电渣焊机electroslag welding with consumable nozzle熔嘴电渣焊electroslag welding with wire electrode丝极电渣焊electrostatic (percussive) welding电能储能焊接electrostatic percussing welding静电焊; 静电焊; 冲击焊; 储能焊electrostatic percussive welding静电冲击焊; 静电冲击焊enclosed welding强制成形焊接energy storage welding贮能焊; 储能焊; 脉冲焊接erecting welding装配焊接erection welding安装焊接eutectic welding低温焊exothermic welding铝热焊expanding or welding of tube with tubesheet管子与管板的胀接或焊接 explosive welding (EW)爆炸焊eyelet welding孔焊; 小孔熔焊faster welding快速焊接feed rate of welding wire焊丝送进速度field of welding temperature焊接温度场field welding现场焊接; 工地焊接Filler arc welding菲拉电弧焊距fillet welding (填角焊)贴角焊fillet welding in the downhand position船形角焊fillet welding in the flat position船形焊fillet welding in the horizontal position横角焊fillet welding in the vertical position立角焊fine welding精密焊接fine wire welding细丝焊fire cracker welding躺焊fire welding锻焊; 锻接fixed welding machine固定式焊机fixed-position welding定位焊接flame welding熔气焊flare welding喇叭形坡口焊接flash butt welding闪光对焊; 闪光对接焊flash welding闪光电弧焊; 闪光焊; 闪焊; 火花电弧焊; 火花对焊flash-butt welding电阻闪光焊接flashover welding闪光焊flat position welding平焊; 顶面平卧焊flat position welding of fillet weld角焊缝平焊; 船形角焊flat welding平卧焊flexible welding rod软焊条flexible wire for electric welding电焊软线flow welding流注焊接; 浇焊fluid welding流焊flux-cored welding包芯焊条焊接fly-wheel type friction welding贮能摩擦焊; 储能摩擦焊flywheel friction welding惯性摩擦焊forehand welding向前焊; 向左焊; 左焊法; 左向焊; 正手焊forge welding锻焊; 锻接焊forward welding正手焊; 左焊法; 左向焊; 前进焊; 前倾焊; 向前焊 friction welding摩擦焊; 摩擦焊接friction welding machine摩擦焊接机frontal fillet welding正面角焊full automatic welding全自动焊full-automatic arc welding全自动电弧焊full-fillet welding满角焊full-fusion thermit welding热剂铸焊full-fusion welding全熔合焊full-length welding满焊fusion pressure welding熔化压接fusion thermit welding热剂熔焊; 熔化铝热焊fusion type plasma arc welding熔透型等离子弧焊fusion type welding熔透型焊接法fusion welding熔焊接fusion welding metal熔焊金属gas carbon-arc welding气保护碳弧焊gas electric welding气电联合焊接gas metal arc welding气体保护金属极电弧焊gas metal-arc welding气保护金属极电弧焊gas shield welding气体保护弧焊gas shielded arc welding气体保护电弧焊; 气体保护焊gas shielded arc welding machine气保护弧焊机gas shielded arc-welding machine气体保护弧焊机gas shielded magnetic flux arc welding磁性焊剂气体保护电弧焊 gas shielded metal-arc welding气体保护金属弧焊gas shielded welding气体保护焊gas torch welding气炬焊gas tungsten arc welding气体保护钨极电弧焊gas tungsten-arc welding气保护钨极电弧焊gas tungstun arc welding钨极气体保护焊gas welding气焊; 乙炔焊gas welding device气焊设备gas welding equipment气焊设备gas welding machine气焊机gas welding outfit气焊机gas welding rod气焊焊丝gas welding rubber hose气焊橡胶管gas welding technique气焊工艺gas welding torch butt气焊进气硬管gas welding tube mill瓦斯焊接机gas welding work气焊工作gas-arc welding气电焊; 气体保护电弧焊gas-arc welding gun气电焊焊嘴gas-press welding气压焊gas-pressure welding machine气压焊接机gas-shielded stud welding气保护柱钉焊接girth welding环缝横向焊接gravity type arc welding重力焊gravity type welding倚焊gravity welding重力焊; 重力式电弧焊groove welding槽焊; 坡口焊; 开槽焊guided automatic welding导向自动焊接gun welding machine手提式点焊机; 点焊枪hafnium welding wire铪焊丝hammer welding锻焊; 锻接; 锤焊hammered resistance welding锤锻电阻焊; 电阻加热锻焊hand welding holdet手焊焊把hard-welding硬质合金熔焊headless bolt for welding焊接单头螺栓heat-welding adhesive热熔性胶粘剂heated-tool welding热烙铁焊接heavy welding大断面焊接heavy welding electrode粗电焊条heliarc welding氦电弧焊Heliarc welding氦弧焊法helium arc welding氦弧焊HF welding magnetic bar高频焊接磁棒hidden arc welding埋弧焊; 潜弧焊high current arc welding大电流弧焊high frequency AC welding machine高频交流电焊机high frequency dielectric welding高频介电焊high frequency induction welding高频感应焊high frequency welding高频焊接high grade energy welding高能焊high tensile electric welding rod高强焊条high-current plasma arc welding大电流等离子弧焊high-frequency induction welding高频感应焊接; 高频焊接high-frequency resistance welding高频接触焊high-frequency resistance welding (HFRW)高频电阻焊high-frequency welding高频电焊highspeed welding快速焊接horizontal fillet welding横角焊; 水平角焊horizontal position welding水平焊接; 横焊horizontal welding横焊; 水平焊horizontal-position welding水平位置焊接horizontal-rolledposition welding水平转动焊接; 滚动水平焊hot jet welding热风焊接hot press welding热压焊接hot pressure welding预热压力焊hot welding热焊hot wire welding热丝焊hot(-)gas welding热气焊接hot-gas welding热风焊接; 热空气焊接hot-pressure welding热压焊; 热压焊接hydrogen-welding氢焊impact spot welding冲击点焊法impregnated-tape metal-arc welding浸焊条金属弧焊impulse current automatic butt welding machine脉冲电流自动对焊机impulse current seam welding machine脉冲电流缝焊机impulse current semiautomatic butt welding machine脉冲电流半自动对焊机impulse electromagnetic automatic welding machine电磁脉冲自动焊机 impulse plasma welding machine脉冲等离子焊机impulse welding脉冲焊; 脉冲焊接impulsed spot welding脉冲点焊inclined position welding倾斜焊indirect (spot) welding单面点焊indirect welding单面点焊induction welding感应焊; 感应焊接; 感应熔焊inert gas arc spot welding惰性气体电弧点焊inert gas arc welding惰性气体电弧焊inert gas spot welding惰性气体保护电弧点焊inert gas welding惰性气体焊接法inert-gas (inert gas) arc welding惰性气体保护焊inertia welding惯性焊接; 贮能摩擦焊; 储能摩擦焊inertial welding惯性焊接infrared welding红外线焊接intermediate current plasma arc welding中电流等离子弧焊 intermittent fillet welding断续角焊intermittent point welding断续点焊intermittent welding断续焊International Institute of welding (IIW)国际焊接学会inverted welding仰焊joint welding搭焊jump welding丁字形焊keyhole-mode welding小孔型等离子弧焊; 穿透型焊接法lap fillet welding搭角焊; 搭接角焊lap resistance welding搭接电阻焊lap seam welding搭接缝焊; 搭接焊lap welding搭焊; 搭接焊laser welding激光焊接laser welding chamber激光焊接室laser welding head激光焊接头laser welding machine for orthodontics激光口腔矫形焊接机 laser welding system激光焊接系统laser-beam welding machine激光焊接机laser-welding machine激光焊接器lead welding铅焊lefthand welding左焊法leftward welding左向焊法lever gun welding head杠杆式点焊钳light beam welding machine光束焊机light continuous welding轻连续焊接light gauge welding薄板焊接light ray welding光束焊接light welding轻焊接Linde welding林德钢管对焊法line welding直线焊缝焊接liquid metal welding浇注补焊longitudinal resistance seam welding纵向电阻缝焊longitudinal seam welding纵缝焊接; 纵向缝焊longitudinal welding纵缝焊接; 纵向焊接low carbon steel welding electrode低碳钢电焊条low carbon welding wires低碳焊接线材low idle voltage arc-welding power supply低空载电压的弧焊电源low temperature welding低温焊接low-alloy steel covered arc welding electrode低合金钢焊条low-current plasma arc welding小电流等离子弧焊low-hydrogen welding electrode低氢型电焊条low-temperature welding低温焊接lowest permissible temperature for welding焊接允许的最低温度machine for magnetic welding磁力焊接机machine welding机器焊接machine welding torch机械焊接吹管magnetic discharge welding电磁储能焊; 电磁焊magnetic flux arc welding磁性焊剂电弧焊magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊magnetic force welding machine磁力焊接机magnetic-force welding磁力焊接法manual arc welding手工电弧堆焊manual electic arc pile up welding手工电弧堆焊manual electric arc welding手工电弧堆焊manual electro-slag welding手工电渣焊manual gas welding手工气焊manual metal-arc welding手弧焊manual TIG welding手工钨极惰性气体保护焊manual welding手工焊接; 人工焊接manual welding machine手工焊机manually coating welding electrode手涂焊条mash seam welding滚压电阻缝焊mash stitch welding多针缝式焊接mask welding电焊眼罩match assemble welding装架焊接metal arc welding金属电弧焊metal buried welding埋渣焊metal inert gas arc welding (MIG)惰性气体金属电弧焊metal inert-gas arc welding金属极惰性气体保护焊metal inertia gas welding金属焊条惰性气体保护焊; 熔化极惰性气体保护焊 metal rectifier welding set整流焊机metal-arc gas-shielded welding气保护金属极电弧焊metal-arc gas-shielded welding (MAGSW)金属极气保护焊metal-arc welding金属极电弧焊micro resistance welding显微电阻焊micro-gap welding微间隙焊接micro-plasma arc welding微束等离子弧焊micro-welding微型焊接; 显微焊接microgap welding微隙间隙焊Miebach high efficiency flash welding machine米巴赫高效闪光对焊机 mild steel arc welding electrode低碳钢焊条mild steel welding rod低碳钢焊丝miter welding斜接头焊接mixed gas arc welding混合气体保护电弧焊molten bath arc welding熔池电弧焊molten-bath arc welding熔池焊motor driven welding machine电动焊机; 电动机拖动式焊机motor-driven welding machine电动旋转式焊机motor-generator welding unit电动直流发电焊接设备multi-head automatic arc-welding machine多头自动电弧焊机multi-head automatic welding machine多头自动焊机multi-operator welding set多站电焊机multi-pass (multiple pass) welding多道焊multiarc welding多弧焊multihead automatic arc welding machine多弧自动电焊机multilayer welding多层焊multioperator welding generator多工位焊接发电机multioperator welding machine多站电焊机; 多站焊机multioperator welding set多站焊机multipass welding多道焊接multiple arc welding多弧焊multiple operator arc welding machine复式弧焊机multiple projection welding多点凸焊multiple resistance welding多点电阻焊接; 复式电阻焊multiple spot welding多点点焊multiple spot welding machine多点点焊机multiple-arc welding plant多弧焊接机multiple-electrode spot welding machine多极点焊机multiple-electrode welding多焊条焊接multiple-impulse welding多脉冲焊; 多脉冲接触焊multiple-operator welding-unit多重操作焊接单元multiple-spot welding多点焊multiple-wire multiple-power submerged-arc welding多丝埋弧焊multiple-wire submerged arc welding多丝埋弧焊multiplewire submerged-arc welding多丝埋弧焊nail head type welding钉头式焊接narrow gap one side welding窄间隙单面焊narrow gap one-side automatic welding窄间隙单面自动电弧焊narrow gap welding窄间隙焊接; 狭间隙焊。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
WeldingThere are a number of methods of joining meta l articales together,depending on the type of meta l and the strength of the joint which is reqired.Soldering gives a satisfactory joint for light articles of steel,copper or brass.but the strength of a soldeing is rather less than a joint which is brazed,riveted or welded.These methods of jointing meta l are normally adopted for srtong permanent joint.The simplest method of welding two pieces of meta l toghter is known as pressure welding.The ends of meta l are heated to a white heat-for iorn,the welding temperature should be about 1300℃-in a flame.At this temperature the meta l becomes plastic.The ends are then pressed or hammered together,and the joint is stoothed off.Care must be taken to ensure that the surface are thoroughly clean first,for dirt will weaken the weld.Moreover, the heating of iron or steel to a high temperature causes oxidation,and a firm of oxide is formed on the heated surfaces.For this reason,a flux is applied to the heated meta l.At welding heat,the flux meta ls,and oxide particles are dissolved in it together with any other imputities,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used ,but for fairly thick bars of meta l,a vee-shaped weld should normally be employed.It is rather stonger than the ordinary butt weld.The heat of fusion welding is generated in several ways,depending on the sort of meta l which is being welded and on its shape.An extremely hot flame can be produced from an oxyacetylene torch. For certain welds an electric arc is used. In this method,an electric current is passed across two electrodes,and the meta l surface are placed between them.The electrodes are sometimes made of carbon,but more frequently they are meta lllic. The work itself constitutes one of them and the other is an insulated filler rod. An arc is stuck between the two ,and the heat which is generated melts the meta l at the weld. A different method, known as spot welding, is usually employed for welding sheets of meta l toghter. Spot welding requires both an electric current and a forging pressure to produce the weld. The two sheets to be spot welded are griped between copper electrodes through which a heavy current is passed; fusion occurs at the spots where the electrodes are thus applied. meta ls of low electrical resistence will be different to spot weld, whereas those of high resistance,such as stainless will produce a spot weld readily.翻译如下：焊接第一段：There are a number of methods of joining meta l articales together,depending on the type of meta l and the strength of the joint which is reqired。
连接金属的方法很多，其分类方法取决于金属的类型和所需求的焊点的强度。
（注意：depending on …. is reqired是现在分辞状语，起到补充说明作用，而which is reqired是定语从句，修饰the join）Soldering gives a satisfactory joint for light articles of steel,copper or brass.but the strength of a soldeing is rather less than a joint which is brazed,riveted or welded.软铅焊使轻钢件、铜件或黄铜件的焊点非常好。
但是软铅焊焊点的强度要远小于铜焊、铆接或焊接的焊点强度。
(Soldering:软铅焊, rather…than,是一个比较修辞，表达的是前后两种事物相比较)These methods of jointing meta l are normally adopted for srtong permanent joint.这些连接金属的方法通常用于焊接高强度的永久焊点。
（of jointing meta l作为一个定语来修饰methods，be adopted for,被用于）第二段：The simplest method of welding two pieces of meta l toghter is known as pressure welding.把两块金属焊接在一起的的最简单的方法就是压力焊。
The ends of meta l are heated to a white heat -for iorn,the welding temperature should be about 1300℃-in a flame.用火焰把金属端部加热至白热状态---对铁而言焊接温度大约为1300℃。
（注意：两个破折号，第一个即：-for iorn，是起转折作用，以铁为例，第二个即：-in a flame，起补充说明，它做的是状语，不是修饰1300℃，是用来修饰are heated，即：用火焰加热）At this temperature the meta l becomes plastic在此温度下，金属变成为塑性的。
The ends are then pressed or hammered together,and the joint is stoothed off.。
之后金属端部就会被施压或锤击而结合在一起，并且焊点会被抹平。
Care must be taken to ensure that the surface are thoroughly clean first,for dirt will weaken the weld要注意的是确保金属表面首先是要完全清洁的，因为污污会使焊缝的强度减弱。
（后面的for 表示的原因，weaken：使…减弱）Moreover, the heating of iron or steel to a high temperature causes oxidation,and a firm of oxide is formed on the heated surfaces. For this reason,a flux is applied to the heated meta l此外，把铁或钢加热到较高的温度会引起氧化，在加热表面会形成一层氧化物。
由此，常在加热金属中加入一种助熔剂。
（注意：要分清句子的结构就比较好翻译了：比如：第一句中：主语：the heating谓语：causes宾语：oxidation）At welding heat,the flux meta ls,and oxide particles are dissolved in it together with any other imputities,and the flux is squeezed out from the center of the weld.在焊接温度，助熔剂熔化了，氧化物颗粒以及其它可能出现的杂质都会熔化于助熔剂。