汽车冲压件---英文名称
汽车制造专业英语词汇大全(4000词条)
汽车专业词汇Assembly line组装线[ə'sɛmbli] Layout布置图Conveyer流水线物料板[kən'veɚ] Rivet table拉钉机['rɪvɪt]Rivet gun拉钉枪Screw driver起子[skru]Electric screw driver电动起子[ɪ'lɛktrɪk]Pneumatic screw driver气动起子[numætɪk]worktable 工作桌OOBA开箱检查Out Of Box Auditfit together组装在一起fasten锁紧(螺丝) ['fɑ:sən]fixture 夹具(治具) ['fɪkstʃɚ]pallet栈板（托盘）['pælət]barcode条码['bɑrkod]barcode scanner条码扫描器['skænɚ] fuse together熔合[fjuz]fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查[kɒz'metɪk]inner parts inspect内部检查['ɪnɚ]thumb screw大头螺丝[θʌm]lbs. inch镑、英寸EMI gasket导电条['ɡæskɪt]front plate前板[pleɪt]rear plate 后板[riə]chassis 基座['ʃæsi]bezel panel面板['bez(ə)l] ['pænl]power button电源按键['bʌtn]reset button重置键[riː'set]Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件[ʃiːt] ['met(ə)l]plastic parts塑胶件['plæstɪk]material check list物料检查表[mə'tɪərɪəl]work cell工作间[sel]trolley台车['trɔli]carton纸箱['kɑːt(ə)n]sub-line支线personnel resource department人力资源部[pɜːsə'nel] ['risɔrs]production department生产部门planning department企划部QC Section品管科['sekʃən]stamping factory冲压厂['stæmpɪŋ]painting factory烤漆厂['peɪntɪŋ]molding factory成型厂['məʊldɪŋ]common equipment常用设备['kɒmən][ɪ'kwɪpmənt]uncoiler and straightener整平机[ʌn'kɔilə]['streitənə]punching machine 冲床['pʌntʃɪŋ]gripper机械手['grɪpɚ]hydraulic machine油压机[haɪ'drɔlɪk]lathe车床[leɪð]planer |'plein|刨床['pleɪnə]miller铣床['mɪlə]grinder磨床['graɪndə]linear cutting线切割['lɪnɪə]electrical sparkle电火花[ɪ'lektrɪk(ə)l] ['spɑːk(ə)l]welder电焊机['weldə]staker=reviting machine铆合机position职务president董事长['prezɪd(ə)nt]general manager总经理special assistant manager特助['speʃ(ə)l] [ə'sɪst(ə)nt]factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理[ə'sɪst(ə)nt]to move, to carry, to handle搬运be put in storage入库['stɔːrɪdʒ]pack packing包装to apply oil擦油[ə'plaɪ]to file burr 锉毛刺[faɪl] [bɜː]final inspection终检to connect material接料[kə'nekt]to reverse material 翻料[rɪ'vɜːs] wet station沾湿台[wet]Tiana天那水cleaning cloth抹布[klɒθ]to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废[skrept]scrape ..v.刮;削[skreɪp]deficient purchase来料不良[dɪ'fɪʃ(ə)nt] ['pɜ:tʃəs]manufacture procedure制程[mænjʊ'fæktʃə][prə'siːdʒə]deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤[skrætʃ]dents压痕defective upsiding down抽芽不良defective to staking铆合不良[dɪ'fektɪv]feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善[prə'pəʊz(ə)l] [ɪm'pruːvm(ə)nt]spare parts备件[speə]forklift叉车['fɔːklɪft]trailer=long vehicle拖板车['treɪlə]compound die合模['kɒmpaʊnd]die locker锁模器pressure plate=plate pinch压板['preʃə]bolt螺栓[bəʊlt]administration/general affairsdept总务部[ədmɪnɪ'streɪʃ(ə)n]automatic screw driver电动启子[ɔːtə'mætɪk]thickness gauge厚薄规['θiknis][geɪdʒ]power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单[aɪ'dentɪfaɪ]screwdriver holder起子插座pedal踩踏板['ped(ə)l]stopper阻挡器flow board流水板[fləʊ] [bɔːd]hydraulic handjack油压板车[haɪ'drɔːlɪk]pallet栈板（托盘）['pælɪt]glove(s)手套[glʌv]glove(s) with exposed fingers割手套[ɪk'spəʊzd]thumb大拇指[θʌm]forefinger食指['fɔːfɪŋgə]midfinger中指ring finger无名指little finger小指band-aid创可贴industrial alcohol工业酒精['ælkəhɒl] alcohol container沾湿台[kən'teɪnə] head of screwdriver起子头vacuum cleaner吸尘器['vækjʊəm]rag 抹布[ræg]garbage container灰箕['gɑːbɪdʒ] garbage can垃圾箱garbage bag垃圾袋chain链条[tʃeɪn]jack升降机chain链条槽magnetizer加磁器['mægnitaizə]lamp holder灯架to mop the floor拖地[mɒp]to clean the floor扫地to clean a table擦桌子air pipe 气管[paɪp]packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷[ɪk'sesɪv]critical defect极严重缺陷['krɪtɪk(ə)l]major defect主要缺陷['meɪdʒə]minor defect次要缺陷['maɪnə]not up to standard不合规格['stændəd]dimension/size is a little bigger尺寸偏大(小) [dɪ'menʃ(ə)n]slipped screwhead/slippery screwhead螺丝滑头[slɪpt]slipped screwhead/shippery screwthread滑手[θred]speckle斑点['spek(ə)l]mildewed=moldy=mouldy发霉['mɪldud]rust 生锈[rʌst]deformation 变形[,diːfɔː'meɪʃ(ə)n]burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污[griːs] [sten]inclusion杂质[ɪn'kluːʒ(ə)n]painting peel off脏污shrinking/shrinkage缩水 ['ʃrɪŋkɪdʒ]mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色[dɪskʌlə'reɪʃn]water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露[ɪk'spəʊzd] [beə]lack of painting烤漆不到位safety安全quality品质delivery deadline交货期[dɪ'lɪv(ə)rɪ]['dedlaɪn]cost成本engineering工程enterprise plan['entəpraɪz]=enterprise expansion projects企划[ɪk'spænʃən]QC品管equipment设备[ɪ'kwɪpm(ə)nt]classification整理[,klæsɪfɪ'keɪʃ(ə)n]regulation整顿[regjʊ'leɪʃ(ə)n] cleanness清扫['klinnɪs]conservation清洁[kɒnsə'veɪʃ(ə)n] culture教养['kʌltʃə]qualified products, up-to-grade products良品['kwɒlɪfaɪd]defective products, not up-to-grade products不良品[dɪ'fektɪv]waste废料[weɪst]board看板[bɔrd]feeder送料机['fiːdə]sliding rack滑料架['slaɪdɪŋ] [ræk] defective product box不良品箱mould change 换模[məʊld]mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板['aisəleitiŋ]carton box纸箱['kɑːt(ə)n]to pull and stretch拉深[stretʃ]to put material in place, to cutmaterial, to input落料to impose lines压线[ɪm'pəʊz]to compress, compressing压缩to feed, feeding送料transportation运输[trænspɔː'teɪʃ(ə)n](be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更['fiːtʃə]evaluation评估[ɪˌvæljuˈeɪʃn]prepare for, make preparations for准备[prɪ'peə]parameters参数[pə'ræmitə]rotating speed, revolution转速[rə(ʊ)'teɪt] [revə'luːʃ(ə)n]manufacture management制造管理[mænjʊ'fæktʃə]abnormal handling异常处理[æb'nɔːml]['hændlɪŋ]production unit生产单位['juːnɪt]steel plate钢板[stiːl]roll material卷料manufacture procedure制程[prə'siːdʒə]operation procedure作业流程to revise, modify修订[rɪ'vaɪz]['mɒdɪfaɪ]to switch over to, switch---tothrow--over switching over切换[swɪtʃ]engineering, project difficulty工程瓶颈automation自动化[ɔːtə'meɪʃ(ə)n]to stake, staking, reviting铆合[steɪk]add lubricating oil加润滑油['lʊbrɪ,ket]shut height of a die架模高度analog-mode device类模器[dɪ'vaɪs]argon welding氩焊['ɑrgɑn] ['weldɪŋ]stamping, press冲压['stæmpɪŋ]punch press, dieing out press冲床[pʌn(t)ʃ]uncoiler & straightener整平机[ʌn'kɔilə] ['streitənə]feeder送料机rack, shelf, stack料架[ræk][ʃelf][stæk]cylinder油缸['sɪlɪndə]conveyer belt输送带[kən'veɚ]transmission rack输送架[træns'mɪʃən]inch寸动[ɪn(t)ʃ]to continue, cont.连动[kən'tɪnjuː]to grip(material)吸料[grɪp]location lump, locating piece, block stop 定位块[lʌmp] [piːs]reset复位[riː'set]smoothly顺利['smuːðlɪ]dent压痕deformation变形filings铁削['faɪlɪŋz]to draw holes抽孔inquiry, search for查寻[ɪn'kwaɪrɪ]to stock, storage, in stock库存receive领取[rɪ'siːv]processing, to process加工delivery, to deliver 交货[dɪ'lɪvəri] to return delivenry to.registration登记['rɛdʒɪ'streʃən] registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收[ək'sɛptəns]to notice通知['nəʊtɪs]application form for purchase请购单[ˌæplɪ'keɪʃ(ə)n] ['pɜ:tʃəs]consume, consumption消耗[kən'sjuːm][kən'sʌmpʃən]to fill in填写abrasion磨损[ə'breɪʒ(ə)n]reverse angle = chamfer倒角['tʃæmfə]character die字模['kærəktə]to collect, to gather收集[kə'lekt]['gæðə]failure, trouble故障['feɪljə]statistics统计demand and supply需求[dɪ'mɑːnd]career card履历卡[kə'rɪə]to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件['dæmɪdʒd]standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑['luːbrɪkeɪt]common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档['fɪgə]cutting die, blanking die冲裁模progressive die, follow (-on)die连续模[prə'gresɪv]compound die复合模['kɒmpaʊnd]punched hole冲孔[pʌntʃt]to cutedges=side cut=side scrap切边to bending折弯['bendɪŋ]to pull, to stretch拉伸[stretʃ]Line streching, line pulling线拉伸engraving, to engrave刻印[ɪn'ɡrevɪŋ]upsiding down edges翻边['ʌpsaɪd]to stake铆合[steɪk]designing, to design设计[dɪ'zaɪnɪŋ]design modification设计变化[,mɑdɪfɪ'keʃən]folded block折弯块sliding block滑块['slaɪdɪŋ]location pin定位销lifting pin顶料销[lɪft]die plate, front board模板padding block垫块['pædɪŋ]stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品[speə]spring 弹簧bolt螺栓document folder文件夹[dɑkjəmənt] ['fəʊldə]file folder资料夹[faɪl]to put file in order整理资料spare tools location手工备品仓[speə]first count初盘人[kaʊnt]first check初盘复棹人second count 复盘人second check复盘复核人equipment设备[ɪ'kwɪpmənt]work in progress product在制品casing = containerazation装箱['keɪsɪŋ]quantity of physical inventorysecond count 复盘点数量['fɪzɪkl]['ɪnvəntɔri]quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查['ref(ə)r(ə)ns]end-user/using unit(department)使用单位summary of year-end physicalinventory bills['sʌməri] [bɪl]年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀[pleɪt]mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位[dɪstrɪ'bjuːʃ(ə)n]location地点chairman主席['tʃeəmən]subject主题conclusion结论decision items决议事项[dɪ'sɪʒ(ə)n]responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / preparedby核准/审核/承办PCE assembly production schedulesheet [ˈʃɛdjuːl]PCE组装厂生产排配表work order工令remark备注production control confirmation生产确认[kɒnfə'meɪʃ(ə)n]approved by核准[ə'pruːvd]department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用[ə'veləbl]obsolete material良品已呆滞['ɔbsəli:t]to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量[kaʊnt]difference quantity差异量cause analysis原因分析raw materials原料[rɔː]materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品[dɪ'spəʊzd]warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单[speə]spare molds location模具备品仓skid/pallet栈板[skɪd] ['pælət]tox machine自铆机wire EDM线割[waɪə]EDM放电机coil stock卷料[kɔɪl]sheet stock片料tolerance工差['tɑlərəns]score=groove压线[skɔː] [gruːv]cam block滑块[kæm]pilot导正筒['paɪlət]trim剪外边[trɪm]pierce剪内边[pɪəs]drag form压锻差[dræg] [fɔːm]pocket for the punch head挂钩槽slug hole废料孔[slʌg]expansion dwg展开图[ik'spænʃən]radius半径['redɪəs]shim(wedge)楔子[ʃɪm] [wedʒ]torch-flame cut火焰切割[tɔrtʃ] [fleɪm]set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子[ʃeɪp]stock locater block定位块under cut=scrap chopper清角active plate活动板['æktɪv]baffle plate挡块['bæf(ə)l]cover plate盖板groove punch压线冲子[gruːv]air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套['bʊʃɪŋ] [blɒk]insert 入块[ɪn'sɜːt]club car高尔夫球车capability能力[ˌkeɪpəˈbɪləti]parameter参数[pə'ræmɪtə]factor系数['fæktə]phosphate皮膜化成['fɒsfeɪt] viscosity涂料粘度[vɪ'skɒsɪtɪ] alkalidipping脱脂main manifold主集流脉bezel斜视规['bez(ə)l]blanking穿落模['blæŋkiŋ]dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次[rɪ'vɪʒən]part number/P/N料号defective products不良品finished products成品disposed products处理品[dɪ'spəʊzd]barcode条码['bɑrkod]flow chart流程表单[tʃɑːt]assembly组装molding成型spare parts=buffer备品coordinate座标[ko'ɔrdɪnet]dismantle the die折模[dɪs'mæntl]auxiliary fuction辅助功能[ɔːɡ'zɪlɪəri]poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机['draɪə]induction感应[ɪn'dʌkʃən]induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线[ˈwɪtnɪs]patent专利['pætnt]grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲['kʊʃən]magnalium镁铝合金magnesium镁金metal plate钣金lathe车[leɪð]mill锉[mɪl]plane刨[pleɪn]grind磨[graɪnd]drill钻[drɪl]boring镗['bɔːrɪŋ]blister气泡['blɪstə]fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔[kæm]shank摸柄[ʃæŋk]crank shaft曲柄轴augular offset角度偏差['æŋgjʊlə]production tempo生产进度现状['tempəʊ]torque扭矩[tɔrk]spline=the multiple keys花键[splaɪn] quenching淬火['kwentʃɪŋ]tempering回火['tempərɪŋ]annealing退火[ə'nilɪŋ]carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯['bikən]coolant冷却液['kuːl(ə)nt]crusher破碎机['krʌʃɚ]模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔[pɪəs]forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数['fæktə]upward向上['ʌpwəd]downward向下['daʊnwəd]press specification冲床规格burr毛边[bɜː]gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销[gaɪd]wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute Dimension Measuremat全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIH When,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID Manufacturing CAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memory module单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形 lowpressure casting 低压铸造lost wax casting 脱蜡铸造 matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plungermold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模 louveringdie 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模 modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positivemold 半全压式模具shaper 定型模套 single cavity mold单腔模具split mold 双并式模具spruelessmold 无注道残料模具sweeping mold 平刮铸模 swing die振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universalmold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模。
汽车制造专业英语词汇大全
汽车制造专业英语词汇大全Document serial number【KKGB-LBS98YT-BS8CB-BSUT-BST108】汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner partsinspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test ofSPS高源高压测试Voltage switchof SPS电源电压接拉键sheet metalparts 冲件plastic parts塑胶件material checklist物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnelresourcedepartment人力资源部productiondepartment生产部门planningdepartment企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler andstraightener整平机punching machine冲床gripper机械手hydraulicmachine油压机lathe车床planer|'plein|刨床miller铣床grinder磨床linear cutting线切割electricalsparkle电火花welder电焊机staker=revitingmachine铆合机position职务president董事长general manager总经理specialassistantmanager特助factory director厂长departmentdirector部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长groupleader/superviso r组长line supervisor 线长assistant manager助理to move, to carry, to handle 搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection 终检to connect material接料to reversematerial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unloadmaterial卸料to returnmaterial/stockto退料scraped|'skræpid|报废scrape ..v.刮;削deficientpurchase来料不良manufactureprocedure制程deficientmanufacturingprocedure制程不良oxidation |'ksi'dein|氧化scratch刮伤dents压痕defectiveupsiding down抽芽不良defective tostaking铆合不良feeding is notin place送料不到位stamping-missing漏冲education andtraining教育与训练proposalimprovement提案改善spare parts备件forklift叉车trailer=longvehicle拖板车compound die合模die locker锁模器pressureplate=platepinch压板bolt螺栓administration/general affairsdept总务部automaticscrewdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defectiveproduct label不良标签identifyingsheet list标示单screwdriverholder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulichandjack油压板车pallet栈板glove(s)手套glove(s) withexposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor 拖地to clean the floor扫地to clean a table 擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessivedefects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up tostandard不合规格dimension/sizeis a littlebigger尺寸偏大(小)slippedscrewhead/slippery screw head螺丝滑头slippedscrewhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oilstains油污inclusion杂质painting peeloff脏污shrinking/shrinkage缩水mixed color杂色poor processing制程不良poor incomingpart事件不良fold of pakagingbelt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposedmetal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质deliverydeadline交货期cost成本engineering工程enterprise plan= enterpriseexpansionprojects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualifiedproducts, up-to-grade products良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material 包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress,compressing压缩to feed, feeding送料transportation运输(be)qualfied, upto grade合格not up to grade,not qualified不合格material change,stock change材料变更feature change特性变更evaluation评估prepare for,makepreparations for准备parameters参数rotating speed,revolution转速manufacturemanagement制造管理abnormalhandling异常处理production unit生产单位steel plate钢板roll material卷料manufactureprocedure制程operationprocedure作业流程to revise,modify修订to switch overto, switch---tothrow--overswitching over切换engineering,projectdifficulty工程瓶颈automation自动化to stake,staking,reviting铆合add lubricatingoil加润滑油shut height of adie架模高度analog-modedevice类模器argon welding氩焊stamping, press冲压punch press,dieing out press冲床uncoiler &strainghtener整平机feeder送料机rack, shelf,stack料架cylinder油缸conveyer belt输送带transmissionrack输送架inch寸动to continue,cont.连动to grip(material)吸料location lump,locating piece,block stop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to. registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance =receive验收to notice通知application formfor purchase请购单consume,consumption消耗to fill in填写abrasion磨损reverse angle =chamfer倒角character die字模to collect, togather收集failure, trouble故障statistics统计demand andsupply需求career card履历卡to take apart adie卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away adie plate移走模板easily damagedparts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑commonvocabulary fordie engineering模具工程常用词汇die 模具figure file,chart file图档cutting die,blanking die冲裁模progressive die,follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=sidecut=side scrap切边to bending折弯to pull, tostretch拉伸Line streching,line pulling线拉伸engraving, toengrave刻印upsiding downedges翻边to stake铆合designing, todesign设计designmodification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, frontboard模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder 文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progressproduct在制品casing =containerazation装箱quantity ofphysicalinvetory secondcount 复盘点数量quantity ofcustoms count会计师盘,点数量the first page第一联filed byaccountingdepartment forreference会计部存查end-user/usingunit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet andphysicalinventory listwill be sent toaccountingDepartmenttogether (Thoseof NHK will besent tofinancialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Applicationstatus recordsof year-endphysicalinventory Listandphysicalinventory card年终盘点卡与清册使用－状况明细表blank and wastesheet NO.空白与作废单号plate电镀mold成型material forengineering moldtesting工程试模材料sample样品incomingmaterial to beinspected进货待验description品名steel/rolledsteel钢材Materialstatistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distributiondepartment分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet 库存货龄分析表on-hand inventory现有库存availablematerial良品可使用obsoletematerial良品已呆滞to be inspectedor reworked待验或重工total合计causedescription原因说明part number/ P/N料号type形态item/group/class类别quality品质notes说明year-endphysicalinventorydifferenceanalysis sheet年终盘点差异分析表physicalinventory盘点数量physical countquantity帐面数量differencequantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finishedproduct半成品packingmaterials包材goodproduct/acceptedgoods/ acceptedparts/good parts良品defectiveproduct/non-goodparts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare partsphysicalinventory list备品盘点清单spare moldslocation模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for thepunch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut 火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button 圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-boxeject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speedtransmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defectiveproducts不良品finishedproducts成品disposedproducts处理品barcode条码flow chart流程表单assembly组装molding成型spareparts=buffer备品coordinate座标dismantle thedie折模auxiliaryfuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derustingmachine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=gr ain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo 生产进度现状torque扭矩spline=themultiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten highspeed steel钨高速的moly high speedsteel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-marknearside正面压印tick-markfarside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质materialthickness料片厚度factor系数upward向上downward向下pressspecification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guidingpost内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin 浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shapepunch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting blockfor location定位支承块air cushionplate气垫板air-cushioneject-rod气垫顶杆trimming punch切边冲子stiffening ribpunch = stinger加强筋冲子ribbon punch压筋冲子reel-stretchpunch卷圆压平冲子guide plate定位板sliding block滑块sliding dowelblock滑块固定块active plate活动板lower slidingplate下滑块板upper holderblock上压块upper mid plate上中间板spring box弹簧箱spring-boxeject-rod弹簧箱顶杆spring-boxeject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sionmolding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulationmolding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=~w=L=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripperplate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=~diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ~Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC qualitycontrol 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI firstarticleinspection 新品首件检查TVR toolverificationreport 模具确认报告3B 3B 模具正式投产前确认CP capabilityindex 能力指数CPK capabilityindex of process模具制程能力参数SSQAstandardizedsupplier quality合格供应商品质评估OOBA out of boxaudit 开箱检查QFD qualityfunctiondeployment 品质机能展开FMEA failuremodeleffectivenessanalysis 失效模式分析8 disciplines8项回复内容FA final audit最後一次稽核CAR correctiveaction request改正行动要求correctiveaction report改正行动报告FQC运作类AQL AcceptableQuality Level运作类允收品质水准S/S Sample size抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ AverageOutput Quality平均出厂品质AOQL AverageOutput QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STDMilitary-Standard 军用标准S I-S IVSpecial I-Special IV 特殊抽样水准等级P/N Part Number料号L/N Lot Number特采AOD Accept OnDeviation 特采UAI Use As It首件检查报告FPIR FirstPiece InspectionReport 百万分之一SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility& Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter直径FREQ Frequency频率N Number 样品数其它品质术语类QCC QualityControl Circle品质圈QIT QualityImprovement Team品质改善小组PDCA Plan DoCheck Action 计划执行检查总结ZD Zero Defect零缺点QI QualityImprovement 品质改善QP QualityPolicy 目标方针TQM TotalQualityManagement 全面品质管理MRB MaterialReject Bill 退货单LQL LimitingQuality Level最低品质水准RMA ReturnMaterial Audit退料认可QAN QualityAmelionrateNotice 品质改善活动ADM AbsoluteDimensionMeasuremat 全尺寸测量QT QualityTarget 品质目标7QCTools 7Quality ControllTools 品管七大手法通用之件类ECN EngineeringChange Notes 工程变更通知(供应商)ECO EngineeringChange Order 工程改动要求(客户)PCN ProcessChange Notice工序改动通知PMP ProductManagement Plan生产管制计划SIPSpecification InProcess 制程检验规格SOP 开始生产IS InspectionSpecification成品检验规范PS PackageSpecification包装规范SPECSpecification规格DWG Drawing 图面系统文件类QC QualitySystem 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWSInternational Workman Standard 工艺标准ISOInternational Standard Organization 国际标准化组织GS GeneralSpecification一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-QualityA-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMC Production& MaterialControl 生产和物料控制PPC ProductionPlan Control 生产计划控制MC MaterialControl 物料控制ME ManafactureEngineering 制造工程部PE ProjectEngineering 产品工程部A/C AccountantDept 会计部DC DocumentCenter 资料中心QE QualityEngineering 品质工程(部)QA QualityAssurance 品质保证(处)QC QualityControl 品质管制(课)PD ProductDepartment 生产部LAB Labratry实验室IE IndustrialEngineering 工业工程R&D Research &Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid栈板PO PurchasingOrder 采购订单MO ManufactureOrder 生产单D/C Date Code生产日期码ID/CIdentificationCode (供应商)识别码SWR SpecialWork Request 特殊工作需求L/N Lot Number批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic ofChina 中国大陆 the United States of America 美国E-MAILElectrical-Mail 电子邮件N/A NotApplicable 不适用QTY Quantity数量VS 以及REV Revision版本JIT Just InTime 零库存/及时供货I/OInput/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0极严重不允许ESD Electry-static Discharge静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention知会CC Carbon Copy副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM AnteMeridian 上午PM PostMeridian 下午CD Compact Disk光碟CD-ROM CompactDisk Read-OnlyMemory 只读光碟FDD Floppy DiskDrive 软碟机HDD Hard DiskDrive 碟碟机REF Reference仅供参考CONN Connector连接器CAV Cavity 模穴CAD ComputerAid Design 计算机辅助设计ASS'Y Assembly装配,组装MAT'S Material材料IC IntegratedCircuit 集成电路T/P TruePosition 真位度TYP Type 类型WDR WeeklyDeliveryRequitement 周出货需求CT Cycle Time制程周期L/T Lead Time前置时间(生产前准备时间)S/T StandardTime 标准时间P/M ProductMarket 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/MBoar/Molding(flat cable)C/P Connectorof PCA/P AssemblySPS Switchingpower supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower立式(机箱)DVD DigitalVedio DiskVCD VdeioCompact DiskLCD LiquidCrystal DisplayCAD ComputerAID DesignCAM ComputerAIDManufacturingCAE ComputerAID EngineeringABIOS AchancedBasic input/outputsystem 先进的基本输入/输出系统CMOSComplemeruaryMetoll OxideSemiconductor互补金属氧化物半导体PDA PersonalDigitalAssistant 个人数字助理IC IntegratedCircuit 集成电路ISA IndustryStandardArchitecture 工业标准体制结构MCA MicroChannelArchitecture微通道结构EISA ExtendedIndustryStandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode发光二级管FMEA FailureModeEffectivenes 失效模式分析W/H WireHarness 金属线绪束集组件F/C Flat Calle排线PCB PrintedCircuit Board印刷电路板CAR CorrectionAction Report改善报告NG Not Good 不良WPR WeeklyDeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC MaximumMaterialConditionMMS MaximumMaterial SizeLMC LeastMaterialConditionLMS LeastMaterial Size模具技术用语各种模具常用成形方式accurate diecasting 精密压铸powder forming粉末成形calendaringmolding 压延成形powder metalforging 粉末锻造cold chamber diecasting 冷式压铸precisionforging 精密锻造cold forging 冷锻 press forging冲锻compactingmolding 粉末压出成形 rocking dieforging 摇动锻造compound molding复合成形 rotaryforging 回转锻造compressionmolding 压缩成形rotationalmolding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulationmolding 注入成形sand moldcasting 砂模铸造extrusionmolding 挤出成形shell casting 壳模铸造foam forming 泡成形sinter forging烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting重力铸造slush molding 凝塑成形hollow(blow)molding 中空(吹出)成形squeeze casting高压铸造hot chamber diecasting 热室压铸swaging 挤锻hot forging 热锻transfer molding转送成形injectionmolding 射出成形warm forging 温锻investmentcasting 精密铸造matched diemethod 对模成形法laminatingmethod 被覆淋膜成形 lowpressure casting低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具 loosedetail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模 modularmold 组合式模具double stackmold 双层模具multi-cavitymold 多模穴模具electroformedmold 电铸成形模multi-gate mold复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicatedcavity plate 复板模 positivemold 全压式模具flash mold 溢料式模具progressive die顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold热流道模具prototype mold雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold倒角式模具runlessinjection mold无流道冷料模具sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具split mold 双并式模具 spruelessmold 无注道残料模具sweeping mold 平刮铸模 swing die振动模具three platesmold 三片式模具trimming die 切边模unit mold 单元式模具 universalmold 通用模具unscrewing mold退扣式模具 yoketype die 轭型模模具厂常用之标准零配件air vent valve通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block锁定块coil spring 螺旋弹簧cold punched nut冷冲螺母cooling spiral螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆 drivebearing 传动轴承ejection pad 顶出衬垫 ejector脱模器ejector guidepin 顶出导梢ejector leaderbusher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machinedplate 角形模板finish machinedround plate 圆形模板fixed bolsterplate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch直柄冲头heavily taperedsolid 整体模蕊盒。
汽车冲压件中英对照表
BAR FR END UPR 散热器上横梁BEAM RR BPR INR 后保防撞梁内板BEAM RR BPR OTR 后保防撞梁外板BRACE RR SHELF LH 后行李箱隔板左侧支柱BRACE RR SHELF RH 后行李箱隔板右侧支柱BRACE RR. FLOOR SIDE LH 后地板左边支柱BRACE RR. FLOOR SIDE RH 后地板右边支柱BRACE S/MBR TO FRT FLOOR LH 前纵梁与前地板左连接板BRACKET HOOD RELEASE (LHD) 发罩拉索支架BRACKET RR FLOOR SEAT MTG LH 左后座椅安装支架BRACKET RR FLOOR SEAT MTG RH 右后座椅安装支架BRK S-IMPACT RR FR DR LH 前门防撞杆后支架BRKT ANTI ZIPPER LH 前地板与门槛内板左连接板BRKT BUMPER 前保险杠支架BRKT CTR BPR MTG 后保险杠中部支架BRKT FASCIA MTG 保险杠安装支架BRKT FENDER LWR LH 左侧前轮挡泥板下部支架BRKT FENDER LWR RH 右侧前轮挡泥板下部支架BRKT FENDER UPR LH 左侧前轮挡泥板上部支架BRKT FENDER UPR RH 左侧前轮挡泥板上部支架BRKT FOOT REST (LHD) 踏脚板支架BRKT GLS GUIDE DOOR 玻璃导轨支架BRKT S-IMPACT CTR FR DR 前门防撞杆中支架BRKT S-IMPACT FR FR DR LH 前门防撞杆前支撑板BRKT S-IMPACT FR FR DR RH 前门防撞杆前支撑板BRKT S-IMPACT FR RR DR LH 左后门侧防撞杆前支架BRKT STRIKER 背门锁扣加强板BRKT SUPT S-IMPACT RR DR LH 左后门侧防撞杆支架BRKT SUPT S-IMPACT RR DR RH 右后门侧防撞杆支架BRKT UPR BUMPER MTG 保险杠安装上支架BRKT ENG MOUNT 发动机悬置支架BRKT SPRING HOUSE RH 右前悬挂上支座BRKT FUEL TANK COMMON 油箱安装左后支架BRKT TRAILING ARM INR LH 左后悬挂纵臂安装内支架BRKT TRAILING ARM INR RH 右后悬挂纵臂安装内支架BRKT TRAILING ARM OTR LH 左后悬挂纵臂外支架BRKT TRAILING ARM OTR RH 右后悬挂纵臂外支架BULKHEAD HINGE FRT LWR LH 左侧前门下部铰链加强板隔板BULKHEAD HINGE FRT LWR RH 右侧前门下部铰链加强板隔板BULKHEAD R/FLR S/MBR LH 后地板左纵梁隔板BULKHEAD R/FLR S/MBR RH 后地板右纵梁隔板BULKHEAD SILL 门槛隔板C/MBR BACKBONE 中央通道横梁C/MBR FR END OTR 散热器下横梁外板C/MBR R/FLR 后地板中横梁C/MBR R/SEAT 后地板前横梁下板C/MBR F/FLR LH 前地板左前横梁C/MBR F/FLR RH 前地板右前横梁C/MBR F/FLR RR LH 前地板左后横梁C/MBR FR END, INR CTR 散热器下横梁中内板C/MBR FR END, INR LH 散热器下横梁左内板CHNL GLS GUIDE FR FR DR LH 左前门玻璃导轨CHNL GLS GUIDE FR FR DR RH 右前门玻璃导轨CHNL GLS GUIDE FR RR DR LH 左后门玻璃导轨CHNL GLS GUIDE FR RR DR RH 右后门玻璃导轨CHNL GLS GUIDE RR FR DR RH 右前门后玻璃导轨CHNL GLS GUIDE UPR RR DR LH 左后门上玻璃导轨CHNL GLS GUIDE UPR RR DR RH 右后门上玻璃导轨EXT DASH PANEL LH 前围挡板左下板EXT DASH PANEL RH 前围挡板右下板EXT C/MBR R/FLR LH 后地板中横梁与纵梁左连接板FRAME FR UPR INR LH 左翼子板加强梁内板FRAME FR UPR INR RH 右翼子板加强梁内板FRAME FR UPR OTR LH 左侧翼子板上部边梁外板FRAME FR UPR OTR RH 右侧翼子板上部边梁外板FRONT S/MBR REAR LH 左前纵梁与地板纵梁连接板FRONT, S/MBR REAR RH 右前纵梁与地板纵梁连接板HINGE FUEL FILLER DR 加油口盖铰链HOOK, MUFFLER B/BONE 中央通道消音器挂钩PANEL A PILLAR LWR LH 左A柱下板PANEL A PILLAR LWR RH 右A柱下板PANEL AIR EXTRACTION BOX OTR LH 左侧排气盒外板PANEL AIR EXTRACTION BOX OTR RH 右侧排气盒外板PANEL B PILLAR INNER LH 左侧B柱盖板PANEL B PILLAR INNER LH 左侧B柱内板PANEL B PILLAR INNER RH 右侧B柱盖板PANEL B PILLAR INNER RH 右侧B柱内板PANEL BODY SIDE OTR LH 左侧围外板PANEL BODY SIDE OTR RH 右侧围外板PANEL CANTRAIL INNER LH 左侧上边梁内板PANEL CANTRAIL INNER RH 右侧上边梁内板PANEL COWL TOP INR (LHD) 空气盒内板PANEL EXT REAR FLR FRT 后地板前连接板PANEL EXT REAR FLR RR 后地板后加强板PANEL FRONT FENDER LH 左前翼子板PANEL FRONT FENDER RH 右前翼子板PANEL FRT HEADER LWR 顶盖前横梁下部板PANEL PILLAR FR INR LH 左A柱内板PANEL PILLAR FR INR LH 左侧A柱内板PANEL PILLAR FR INR RH 右A柱内板PANEL PILLAR FR INR RH 右侧A柱内板 PANEL REAR FLOOR 后地板PANEL REAR SHELF 行李架隔板PANEL REINF FRT HINGE A PILLAR LH 左侧A柱铰链加强板PANEL REINF FRT HINGE A PILLAR RH 右侧A柱铰链加强板PANEL ROOF 顶盖PANEL ROOF BOW 顶盖中横梁PANEL RR END INR 后围内板PANEL RR END OTR 后围横梁外板PANEL RR HEADER UPR 顶盖后横梁上板PANEL RR QTR INR LWR LH 左后轮罩外板下段PANEL RR QTR INR LWR RH 右后轮罩外板下段PANEL RR QTR INR UPR LH 左后轮罩外板上段PANEL RR QTR INR UPR RH 右后轮罩外板上段PANEL RR. W/HSE INR LH 左轮罩内板PANEL RR. W/HSE INR RH 右轮罩内板PANEL SILL INR LH 前地板左门槛内板PANEL SILL INR LH 左门槛内板PANEL SILL INR RH 前地板右门槛内板PANEL SILL INR RH 右门槛内板PANEL SPRING HOUSE LH 左前悬挂支座下板PANEL SPRING HOUSE RH 右前悬挂支座下板PANEL COWL TOP OTR 空气盒外板PANEL DASH (LHD) 前围挡板PNL FR DR INR LH 左前门内板PNL FR DR INR RH 右前门内板PNL FR DR OTR LH 左前门外板PNL FR DR OTR RH 右前门外板PNL FUEL FILLER DR 加油口盖外板PNL HOOD INR 发罩内板PNL HOOD OTR 发罩外板PNL RR DR INR LH 左后门内板PNL RR DR INR RH 右后门内板PNL RR DR OTR LH左后门外板PNL RR DR OTR RH 右后门外板PNL T-GATE INR 后背门内板PNL T-GATE OTR 后背门外板PNL TRUNK LID INR 行李箱盖内板PNL TRUNK LID OTR 行李箱盖外板PNL SPRING HOUSE LH 左后悬挂支座下板PNL SPRING HOUSE RH 右后悬挂支座下板REINF A PILLAR UPR LH 左侧A柱上部加强板REINF A PILLAR UPR RH 右侧A柱上部加强板REINF B PILLAR CTR LH 左B柱中加强板REINF B PILLAR CTR RH 右B柱中加强板REINF B PILLAR DOUBLER LH 左侧B柱铰链加强板REINF B PILLAR DOUBLER RH 右侧B柱铰链加强板REINF B PILLAR LH 左侧B柱加强板REINF B PILLAR RH 右侧B柱加强板REINF B PILLAR UPR LH 左侧B柱加强上段REINF B PILLAR UPR RH 右侧B柱加强上段REINF BRACE REAR SHELF LH 行李箱隔板左托架支柱REINF BUMP STOP RH 右侧缓冲器加强板REINF BUMPER STAY LH 后保险杠左缓冲支柱加强板REINF BUMPER STAY RH 后保险杠右缓冲支柱加强板REINF COWL TOP INR (LHD) 转向柱加强板REINF DASH PANEL CTR 前围挡板下加强板REINF DOOR CHECK LH 左侧前门限位器加强板REINF FR END C/MBR SIDE LH 散热器下横梁左侧加强板REINF FRAME UPR FR DR LH 左前门窗框加强板REINF FRAME UPR FR DR RH 右后门窗框加强板REINF FRAME UPR FR DR RH 右前门窗框加强板REINF FRAME UPR RR DR LH 左后门窗框加强板REINF FUEL FILLER DR 加油口盖加强板REINF HINGE FRT UPR LH 左侧前门上部铰链加强板REINF HINGE FRT UPR RH 右侧前门上部铰链加强板REINF HINGE RR DR LH 左后门铰链加强板REINF HINGE RR DR RH 右后门铰链加强板REINF HINGE T-LID LH 行李箱盖铰链左加强板REINF HINGE T-LID RH 行李箱盖铰链右加强板REINF HOOD HINGE LH 发动机罩左侧铰链加强板REINF LATCH FR DR LH 左前门锁加强板REINF LATCH FR DR RH 右前门锁加强板REINF LATCH RR DR RH 右后门锁加强板REINF REAR SHELF FRONT 行李架前加强板REINF SBELT SIDE LH 左前座安全带左下加强板REINF SBELT SIDE RH 左前座安全带左下加强板REINF SILL LH 左侧门槛加强板REINF SILL RH 右侧门槛加强板REINF STG COL BRKT (LHD) 转向柱支架REINF WAIST OTR RR DR RH 右后门窗沿外加强板REINF BACKBONE 中央通道加强板REINF ENG MOUNT 发动机悬置加强板REINF FR END C/MBR 散热器下横梁加强板REINF FR S/MBR INR, FR LH 左前纵梁内板前加强板REINF FR S/MBR INR, FR RH 右前纵梁内板前加强板REINF FR S/MBR INR, RR LH 左前纵梁内板后加强板REINF FR S/MBR OTR LH 左前纵梁外板加强板REINF FR S/MBR OTR REAR LH 左前纵梁外板后加强板REINF FR S/MBR OTR REAR RH 右前纵梁外板后加强板REINF FRT S/MBR, REAR LH 左前纵梁地板纵梁加强板REINF T/M MOUNT 变速箱悬置加强板REINF DASH PANEL (LHD) 前围挡板内加强板REINF R/FLR LH 后地板左加强板REINF R/FLR RH 后地板右加强板REINF C/MBR UPR LH 后地板前横梁下板左加强板REINF C/MBR UPR RH 后地板前横梁下板右加强板REINF R/FLR S/MBR FR LH 后地板左纵梁加强板REINF R/FLR S/MBR FR RH 后地板右纵梁加强板REINF R/FLR S/MBR LH 后地板左纵梁侧加强板REINF R/FLR S/MBR RH 后地板右纵梁侧加强板REINF S/BELT R/FLR 后座椅安全带内加强板S/MBR FR FLR LH 前地板左纵梁S/MBR FR FLR RH 前地板右纵梁S/MBR FR INR LH 左前纵梁内板S/MBR FR INR RH 右前纵梁内板S/MBR FR OTR LH 左前纵梁外板S/MBR FR OTR RH 右前纵梁外板SHIELD FR FENDER LH 左前挡泥板SHIELD FR FENDER RH 右前挡泥板SMBR RR FLR LH 后地板左纵梁SMBR RR FLR RH 后地板右纵梁SUPT R/FLR S/MBR LH 后地板左纵梁支架。
汽车制造专业英语词汇大全
汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧螺丝fixture 夹具治具pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resourcedepartment人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer |'plein&61611;|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager 特助factory director厂长department director部长deputy manager | =vicemanager副理section supervisor课长deputy section supervisor=vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move; to carry; to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturingprocedure制程不良oxidation |'ksi'dei&61611;n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch 压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板gloves手套gloves with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大小slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr金属flash塑件毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surfaceprocessing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan =enterprise expansionprojects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products;up-to-grade products良品defective products; notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place; to cut material; to input落料to impose lines压线to compress; compressing 压缩to feed; feeding送料transportation运输bequalfied; up to grade合格not up to grade; not qualified不合格material change; stockchange材料变更feature change 特性变更evaluation评估prepare for; makepreparations for 准备parameters参数rotating speed; revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise; modify修订to switch over to;switch---to throw--overswitching over切换engineering; projectdifficulty工程瓶颈automation自动化to stake; staking; reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping; press冲压punch press; dieing outpress冲床uncoiler & strainghtener整平机feeder送料机rack; shelf; stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue; cont.连动to gripmaterial吸料location lump; locating piece; block stop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry; search for查寻to stock; storage; in stock 库存receive领取processing; to process加工delivery; to deliver 交货to return delivenry to. registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form forpurchase请购单consume; consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect; to gather收集failure; trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.bebroken;becracked 断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file; chart file图档cutting die; blanking die冲裁模progressive die; follow-ondie连续模compound die复合模punched hole冲孔to cutedges=side cut=sidescrap切边to bending折弯to pull; to stretch拉伸Line streching; line pulling线拉伸engraving; to engrave刻印upsiding down edges翻边to stake铆合designing; to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate; front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physicalinvetory second count 复盘点数量quantity of customs count会计师盘;点数量the first page第一联filed by accountingdepartment for reference会计部存查end-user/usingunitdepartment使用单位summary of year-endphysical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physicalinventory list will be sentto accountingDepartment together Thoseof NHK will be sent tofinancialdepartment本表请与盘点清册一起送会计部－NHK厂区送财会部Application status recordsof year-end physicalinventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly productionschedule sheetPCE组装厂生产排配表work order工令remark备注production controlconfirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physicalinventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physicalinventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shimwedge楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=diebutton圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型抽凸;冲凸draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字料号shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板顶板top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板底板stripping plate内外打脱料板outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块嵌入件deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式模具well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod bar成型机顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口;直浇口nozzle射嘴sprue lock pin料头钩销拉料杆slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道sprue less无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final qualitycontrol 终点品质管制人员IPQC in process qualitycontrol 制程中的品质管制人员OQC output qualitycontrol 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verificationreport 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index ofprocess 模具制程能力参数SSQA standardizedsupplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality functiondeployment 品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective actionrequest 改正行动要求corrective action report改正行动报告FQC运作类AQL Acceptable QualityLevel 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average OutputQuality 平均出厂品质AOQL Average OutputQuality Level 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STDMilitary-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit管制上限LCL Lower Central Limit管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality ControlCircle 品质圈QIT Quality ImprovementTeam 品质改善小组PDCA Plan Do Check Action计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement品质改善QP Quality Policy 目标方针TQM Total QualityManagement 全面品质管理MRB Material Reject Bill退货单LQL Limiting QualityLevel 最低品质水准RMA Return Material Audit退料认可QAN Quality AmelionrateNotice 品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 QualityControll Tools 品管七大手法通用之件类ECN Engineering ChangeNotes 工程变更通知供应商ECO Engineering Change Order 工程改动要求客户PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES EngineeringStandarization 工程标准CGOO China General PCE龙华厂文件H Huston 美国休斯敦C Compaq 美国康伯公司C China 中国大陆A Assembly 组装厂S Stamping 冲压厂P Painting 烤漆厂I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO InternationalStandard Organization 国际标准化组织GS General Specification一般规格CMCS C-China M-ManufactC-Compaq S-StampingCompaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production &Material Control 生产和物料控制PPC Production PlanControl 生产计划控制MC Material Control 物料控制ME ManafactureEngineering 制造工程部PE Project Engineering产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程部QA Quality Assurance 品质保证处QC Quality Control 品质管制课PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆厂A Asssembly 组装厂S Stamping 冲压厂生产类PCS Pieces 个根;块等PRS Pairs 双对等CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code供应商识别码SWR Special Work Request特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal ComputerEnclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central ProcessingUnit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic ofChina 中国大陆U.S.A the United States ofAmerica 美国E-MAIL Electrical-Mail电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行;不合格C=0 Critical=0 极严重不允许ESD Electry-staticDischarge 静电排放5S 希腊语整理;整顿;清扫;清洁;教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准;认可;承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design计算机辅助设计ASS'Y Assembly 装配;组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C T Cycle Time 制程周期L/T Lead Time 前置时间生产前准备时间S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer;Commumcation;Consumer electronic's 消费性电子5WIHWhen;Where;Who;What;Why;How to5MMan;Machine;Material;Method;Measurement4MIHMan;Materia;Money;Method;Time 人力;物力;财务;技术;时间资源SQA Strategy QualityAssurance 策略品质保证DQA Desigh QualityAssurance 设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and serviceQuality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Moldingflat cableC/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式机箱MT Mini-Tower 立式机箱DVD Digital Vedio Disk VCD Vdeio Compact Disk LCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AIDManufacturingCAE Computer AIDEngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal DigitalAssistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro ChannelArchitecture 微通道结构EISA Extended IndustryStandard Architecture 扩充的工业标准结构SIMM Single in-linememory module 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode发光二级管FMEA Failure ModeEffectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board印刷电路板CAR Correction ActionReport 改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定;定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material Size LMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging精密锻造cold forging 冷锻pressforging 冲锻compacting molding 粉末压出成形 rocking die forging摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollowblow molding 中空吹出成形squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raisingembossing 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具 sectional die对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套singlecavity mold 单腔模具split mold 双并式模具sprueless mold 无注道残料模具sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴模仁cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块lockingblock 定位块locking plate 定位板 loosebush 活动衬套manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座moldclamp 铸模紧固夹mold platen 模用板 movingbolster 换模保持装置moving bolster plate 可动侧模板one piece casting整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板 shoot流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slideslide core 滑块slip joint 滑配接头 spacerblock 间隔块spacer ring 间隔环 spider模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线squarekey 方键square nut 方螺帽squarethread 方螺纹stop collar 限位套stoppin 止动梢stop ring 止动环stopper定位停止梢straight pin 圆柱stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械。
汽车制造专业英语词汇大全
汽车专业词汇operator 作业员Assembly line 组装线QC 品管Layout 布置图supervisor 课长Conveyer 流水线物料板ME 制造工程师Rivet table 拉钉机MT 制造生技Rivet gun 拉钉枪cosmetic inspect 外观检查Screw driver 起子inner parts inspect 内部检查Electric screw driver 电动起子thumb screw 大头螺丝Pneumatic screw driver 气动起子lbs. inch 镑、英寸worktable 工作桌EMI gasket 导电条OOBA 开箱检查front plate 前板fit together 组装在一起rear plate 后板fasten 锁紧（螺丝）chassis 基座fixture 夹具（治具）bezel panel 面板pallet 栈板power button 电源按键barcode 条码reset button 重置键barcode scanner 条码扫描器Hi-pot test of SPS 高源高压测试fuse together 熔合Voltage switch of SPSfuse machine 热熔机电源电压接拉键repair 修理sheet metal parts 冲件plastic parts 塑胶件material check list 物料检查表grinder 磨床work cell 工作间linear cutting 线切割trolley 台车electrical sparkle 电火花carton 纸箱welder 电焊机sub-line 支线staker=reviting machine 铆合机personnel resource department position 职务人力资源部president 董事长production department 生产部门general manager 总经理planning department 企划部special assistant manager 特助QC Section 品管科factory director 厂长stamping factory 冲压厂department director 部长painting factory 烤漆厂deputy manager | =vice manager 副molding factory 成型厂理common equipment 常用设备section supervisor 课长uncoiler and straightener 整平机deputy section supervisor =vice punching machine 冲床section superisor 副课长gripper 机械手group leader/supervisor 组长hydraulic machine 油压机line supervisor 线长lathe 车床assistant manager 助理planer |'plein| 刨床to move, to carry, to handle 搬运miller 铣床be put in storage 入库最新可编辑word 文档pack packing 包装 defective upsiding down 抽芽不良 screwdriver holder起子插座garbage can 垃圾箱 to apply oil 擦油 defective to staking 铆合不良 pedal 踩踏板garbage bag 垃圾袋to file burr 锉毛刺 feeding is not in place 送料不到位 stopper 阻挡器chain 链条final inspection 终检 stamping-missing 漏冲flow board 流水板jack 升降机 to connect material 接料 education and training 教育与训练 hydraulichandjack油压板车chain 链条槽 to reverse material 翻料 proposal improvement 提案改善 pallet 栈板magnetizer 加磁器wet station 沾湿台 spare parts 备件 glove(s) 手套lamp holder 灯架 Tiana 天那水 forklift 叉车glove(s) with exposed fingers 割手to mop the floor 拖地 cleaning cloth 抹布 trailer=long vehicle 拖板车 套to clean the floor 扫地to load material 上料 compound die 合模 thumb 大拇指to clean a table 擦桌子 to unload material 卸料die locker 锁模器forefinger 食指air pipe 气管to return material/stock to 退料 pressure plate=plate pinch 压板 midfinger 中指packaging tool 打包机scraped |'skræpid| 报废 bolt 螺栓ring finger 无名指packaging 打包scrape ..v. 刮 ;削administration/general affairs deptlittle finger 小指missing part 漏件deficient purchase 来料不良 总务部band-aid 创可贴wrong part 错件manufacture procedure 制程 automatic screwdriver 电动启子 iudustrialalcohol工业酒精excessive defects 过多的缺陷 deficient manufacturing procedurethickness gauge 厚薄规 alcohol container沾湿台critical defect 极严重缺陷 制程不良power wire 电源线 head of screwdriver 起子头 major defect 主要缺陷 oxidation |' ksi'dein| 氧化 buzzle 蜂鸣器vaccum cleaner 吸尘器minor defect 次要缺陷scratch 刮伤 defective product label 不良标签 rag 抹布not up to standard 不合规格dents 压痕identifying sheet list 标示单garbage container 灰箕dimension/size is a little bigger 尺寸偏大（小）discoloration 羿色products 良品to feed, feeding 送料slipped screwhead/slippery screw water spots 水渍defective products, not up-to-gradetransportation 运输head 螺丝滑头polishing/surfaceprocessing表面处products 不良品（be）qualfied, up to grade 合格slipped screwhead/shippery screw 理waste 废料not up to grade, not qualified不合格thread 滑手exposed metal/bare metal 金属裸露board 看板material change, stock change 材料speckle 斑点lack of painting 烤漆不到位feeder 送料机变更mildewed=moldy=mouldy 发霉safety 安全sliding rack 滑料架feature change 特性变更rust 生锈quality 品质defective product box 不良品箱evaluation 评估deformation 变形delivery deadline 交货期mould change 换模prepare for, make preparations for burr（金属）flash（塑件）毛边cost 成本mold repair 修模准备poor staking 铆合不良engineering 工程packing material 包材parameters 参数excesssive gap 间隙过大enterprise plan = enterprise basket 蝴蝶竺rotating speed, revolution 转速grease/oil stains 油污expansion projects 企划plastic basket 胶筐manufacture management 制造管理inclusion 杂质QC 品管isolating plate baffle plate; abnormal handling 异常处理painting peel off 脏污equipment 设备barricade 隔板production unit 生产单位shrinking/shrinkage 缩水classification 整理carton box 纸箱steel plate 钢板mixed color 杂色regulation 整顿to pull and stretch 拉深roll material 卷料poor processing 制程不良cleanness 清扫to put material in place, to cut manufacture procedure 制程poor incoming part 事件不良conservation 清洁material, to input 落料operation procedure 作业流程fold of pakaging belt 打包带折皱culture 教养to impose lines 压线to revise, modify 修订painting make-up 补漆qualified products, up-to-grade to compress, compressing 压缩to switch over to, switch---tothrow--over switching over 切换stop 定位块单common vocabulary for dieengineering, project difficulty reset 复位consume, consumption 消耗engineering工程瓶颈smoothly 顺利to fill in 填写模具工程常用词汇automation 自动化dent 压痕abrasion 磨损die 模具to stake, staking, reviting 铆合deformation 变形reverse angle = chamfer 倒角figure file, chart file 图档add lubricating oil 加润滑油filings 铁削character die 字模cutting die, blanking die 冲裁模shut height of a die 架模高度to draw holes 抽孔to collect, to gather 收集progressive die, follow (-on)die analog-mode device 类模器inquiry, search for 查寻failure, trouble 故障连续模argon welding 氩焊to stock, storage, in stock 库存statistics 统计compound die 复合模stamping, press 冲压receive 领取demand and supply 需求punched hole 冲孔punch press, dieing out press 冲床processing, to process 加工career card 履历卡to cutedges=side cut=side scrap 切uncoiler & strainghtener 整平机delivery, to deliver 交货to take apart a die 卸下模具边feeder 送料机to return delivenry to. to load a die 装上模具to bending 折弯rack, shelf, stack 料架registration 登记to tight a bolt 拧紧螺栓to pull, to stretch 拉伸cylinder 油缸registration card 登记卡to looser a bolt 拧松螺栓Line streching, line pulling 线拉伸conveyer belt 输送带to control 管制to move away a die plate 移走模板engraving, to engrave 刻印transmission rack 输送架to put forward and hand in 提报easily damaged parts 易损件upsiding down edges 翻边inch 寸动safe stock 安全库存standard parts 标准件to stake 铆合to continue, cont. 连动acceptance = receive 验收breaking.(be)broken,(be)cracked designing, to design 设计to grip(material) 吸料to notice 通知断裂design modification 设计变化location lump, locating piece, block application form for purchase 请购to lubricate 润滑folded block 折弯块sliding block 滑块casing = containerazation 装箱Application status records of chairman 主席location pin 定位销quantity of physical invetory second year-end physical inventory List and subject 主题lifting pin 顶料销count 复盘点数量physical inventory card 年终盘点卡conclusion 结论die plate, front board 模板quantity of customs count 与清册使用－状况明细表decision items 决议事项padding block 垫块会计师盘,点数量blank and waste sheet NO. responsible department 负责单位stepping bar 垫条the first page 第一联空白与作废单号pre-fixed finishing date 预定完成日upper supporting blank 上承板filed by accounting department for plate 电镀approved by / checked by / upper padding plate blank 上垫板reference 会计部存查mold 成型prepared by 核准/审核/承办spare dies 模具备品end-user/using unit(department) 使material for engineering mold PCE assembly production schedulespring 弹簧用单位testing 工程试模材料sheetbolt 螺栓summary of year-end physical sample 样品PCE 组装厂生产排配表document folder 文件夹inventory bills incoming material to be inspected work order 工令file folder 资料夹年终盘点截止单据汇总表进货待验remark 备注to put file in order 整理资料bill name 单据名称description 品名production control confirmation 生产spare tools location 手工备品仓This sheet and physical inventory steel/rolled steel 钢材确认first count 初盘人list will be sent to accounting Material statistics sheet approved by 核准first check 初盘复棹人Department together (Those of 物料统计明细表department 部门second count 复盘人NHK will be sent to financial meeting minutes 会议记录Stock age analysis sheet second check 复盘复核人department) meeting type 会别库存货龄分析表equipment 设备、丰f~rVt. U丰仃口4*-t、¥ 人、distribution department 分发单位本表请与盘点清册一起送会计部－on-hand inventory 现有库存work in progress product 在制品（NHK 厂区送财会部）最新可编辑location 地点word 文档available material 良品可使用obsolete material良品已呆滞 packing materials 包材 pilot 导正筒 groove punch 压线冲子to be inspected or reworkedgood product/accepted goods/ trim 剪外边 air-cushion eject-rod 气垫顶杆 待验或重工accepted parts/good parts 良品 pierce 剪内边 spring-box eject-plate 弹簧箱顶板 total 合计defective product/non-good parts 不drag form 压锻差bushing block 衬套 causedescription原因说明 良品pocket for the punch head 挂钩槽 insert 入块 part number/ P/N料号disposed goods 处理品 slug hole 废料孔 club car 高尔夫球车 type 形态warehouse/hub 仓库expansion dwg 展开图 capability 能力 item/group/class类别on way location 在途仓 radius 半径 parameter 参数 quality 品质oversea location 海外仓shim(wedge) 楔子factor 系数 notes 说明spare parts physical inventory list 备 torch-flame cut 火焰切割phosphate 皮膜化成 year-end physical inventory 品盘点清单set screw 止付螺丝 viscosity 涂料粘度 difference analysis sheetspare molds location 模具备品仓 form block 折刀 alkalidipping 脱脂 年终盘点差异分析表skid/pallet 栈板 stop pin 定位销main manifold 主集流脉 physical inventory盘点数量tox machine 自铆机 round pierce punch=die button 圆冲bezel 斜视规 physical count quantity 帐面数量 wire EDM 线割 子blanking 穿落模 differencequantity差异量EDM 放电机 shape punch=die insert 异形子 dejecting 顶固模cause analysis 原因分析 coil stock 卷料 stock locater block 定位块 demagnetization 去磁 ;消磁 raw materials 原料sheet stock 片料 under cut=scrap chopper 清角 high-speed transmission 高速传递 materials 物料tolerance 工差active plate 活动板 heat dissipation 热传 finished product成品score=groove 压线 baffle plate 挡块 rack 上料 semi-finished product 半成品cam block 滑块cover plate 盖板degrease 脱脂最新可编辑 word 文档。
组装、冲压、喷漆等专有名词(英文)
組裝、衝壓、噴漆等專業詞匯Assembly line組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Pneumatic screw driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME制造工程師MT製造生技cosmetic inspect外觀檢查inner parts inspect內部檢查thumb screw大頭螺絲Lbs. inch鎊、英寸EMI gasket導電條front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button電源按鍵reset button重置鍵Hi-pot test of SPS高源高壓測試V oltage switch of SPS電源電壓接柆鍵sheet metal parts 沖件plastic parts塑膠件SOP製造作業程序material check list物料檢查表work cell工作間trolley台車carton紙箱sub-line支線left fork叉車Personnel resource department人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory沖壓廠painting factory烤漆廠molding factory成型廠common equipment常用設備uncoiler and straightener整平機punching machine 沖床robot機械手hydraulic machine油壓機lathe車床planer |'plein |刨床miller銑床grinder磨床driller鉆床linear cutting線切割electrical sparkle電火花welder電焊機staker = riveting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager |'depjuti| =vicemanager副理section supervisor課長deputy section supervisor =vicesection supervisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|報廢scrape ..v.刮;削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良embedded lump |in'bed| |l mp|鑲塊feeding is not in place送料不到位stamping-missing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts =buffer備件forklift叉車trailer =long vehicle拖板車compound die合模die locker鎖模器pressure plate =plate pinch壓板bolt螺栓name of a department部門名稱administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzer蜂鳴器defective product label不良標簽identifying sheet list標示單screwdriver holder起子插座pedal踩踏板stopper阻擋器flow board流水板hydraulic hand jack油壓板車forklift叉車pallet棧板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指mid finger中指ring finger無名指little finger小指Band-Aid創可貼Industrial alcohol工業酒精alcohol container沾濕台head of screwdriver起子頭sweeper掃把mop拖把vacuum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain鏈條jack升降機production line流水線chain鏈條槽magnetizer加磁器lamp holder燈架to mop the floor拖地to clean the floor掃地to clean a table擦桌子air pipe 氣管packaging tool打包機packaging打包missing part漏件wrong part錯件excessive defects過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外觀不良slipped screw head/slipperyscrew head螺絲滑頭slipped screw head/slipperyscrew thread滑手speckle斑點mildewed =moldy = mouldy發霉rust生銹deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質painting peel off臟污shrinking/shrinkage縮水mixed color雜色scratch劃傷poor processing 制程不良poor incoming part事件不良fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬polishing/surface processing表面處理exposed metal/bare metal金屬裸露lack of painting烤漆不到位safety安全quality品質delivery deadline交貨期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企劃QC品管die worker模工production, to produce生產equipment設備to start a press開機stop/switch off a press關機classification整理regulation整頓cleanness清掃conservation清潔culture教養qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste廢料board看板feeder送料機sliding rack滑料架defective product box不良品箱die change 換模to fix a die裝模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket膠筐isolating plate baffle plate; barricade隔板carton box紙箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料transportation運輸(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacture management製造管理abnormal handling異常處理production unit生產單位lots of production生產批量steel plate鋼板roll material捲料manufacture procedure制程operation procedure作業流程to revise, modify修訂to switch over to, switch---to throw--over switching over切換engineering, project difficulty工程瓶頸stage die工程模automation自動化to stake, staking, riveting鉚合add lubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding氬焊Vocabulary for stamping衝壓常詞匯stamping, press沖壓punch press, dicing out press沖床uncoiled & straightened整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmission rack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue, cont.連動to grip(material)吸料location lump, locating piece,block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry, search for查尋to stock, storage, in stock庫存receive領取approval examine and verify審核processing, to process加工delivery, to deliver 交貨to return delivery to. to senddelivery back to return of goods退貨registration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知application form for purchase請購單consume, consumption消耗to fill in填寫abrasion磨損reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics統計demand and supply需求career card履歷卡to take apart a die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser a bolt擰鬆螺栓to move away a die plate移走模板easily damaged parts易損件standard parts標準件Breaking. (be)broken,(be)cracked斷裂to lubricate潤滑common vocabulary for dieengineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die沖裁模Progressive die, follow (-on) die連續模compound die復合模punched hole沖孔panel board鑲塊to cut edge =side cut =side scrap切邊to bending折彎to pull, to stretch拉伸Line stretching, line pulling線拉伸engraving, to engrave刻印upside down edges翻邊to stake鉚合designing, to design設計design modification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾file folder資料夾to put file in order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count 復盤人second check復盤復核人equipment設備waste materials廢料work in progress product在制品casing = containerization裝箱quantity of physical inventory second count 復盤點數量Quantity of customs counts會計師盤,點數量the first page第一聯filed by accounting departmentfor reference會計部存查end-user/using unit(department)使用單位Summary of year-end physicalinventory bills年終盤點截止單據匯總表bill name單據名稱This sheet and physicalinventory list will be sent toaccounting department together(Those of NHK will be sent tofinancial department)本表請與盤點清冊一起送會計部－(NHK廠區送財會部)Application status records ofyear-end physical inventory Listand physical inventory card年終盤點卡與清冊使用－狀況明細表Blank and waste sheet NO.空白與作廢單號plate電鍍mold成型material for engineering moldtesting工程試模材料not included in physicalinventory不列入盤點sample樣品incoming material to beinspected進貨待驗description品名steel/rolled steel鋼材Material statistics sheet物料統計明細表meeting minutes會議記錄meeting type 會別distribution department分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by /prepared by核準/審核/承辦PCE assembly productionschedule sheetPCE組裝廠生產排配表model機種work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門Stock age analysis sheet庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯To be inspected or reworked待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表notes說明Year-end physical inventorydifference analysis sheet年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts部品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score =groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion DWG展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch =die button圓沖子shape punch =die insert異形子stock located block定位塊under cut =scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkali dipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬despot剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spare parts =buffer備品coordinate座標dismantle the die折模auxiliary function輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除銹機degate 打澆口dryer烘干機induction感應induction light感應光response =reaction =interaction感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule =pellet =grain細粒grit maker抽粒機cushion緩沖magnesium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鋁boring鏜blister氣泡fillet鑲;嵌邊through-hole form通孔形式roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸angular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline =the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸)draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號)shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印沖壓名稱類extension DWG展開圖procedure DWG工程圖die structure DWG模具結構圖material材質material thickness料片厚度factor系數upward向上downward向下press specification沖床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves =spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板) stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件) deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing block襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compression molding壓縮成型flash mold溢流式模具positive mold擠壓式模具split mold分割式模具cavity型控母模core模心公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulation molding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleeve套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口Φ0.8~1.0mmRunner less無澆道(sprue less)無射料管方式long nozzle延長噴嘴方式spur澆口;溶stamping tool shop I stamping tool shop IIPCE mould shop Engineer standard Document centerSystem －Assembly molding painting assembly通用類cosmetic inspection standard 外觀檢驗規範computer case 電腦外殼(組件) personal computer enclosure 電腦機箱產品Hood 上蓋 spsbase pan 基座FDD軟體驅動器bezel 面板riser card 擴充本flat cable 排線sheet material 板村Rou material 卷材mother material to sub－material feeding(喂料)→straightening (整平) rectifying (導正)→longitudinal cutting (縱剪) →separating (分離) →taking(取料)shop－traceller 天本TOP driver cage 上磁架bottom driver cage 干磁架I/O bracket 後窗resin film 樹脂膜impurity 雜質grease 油脂ventilation 通風peripheral equipment’s connector 外圍(輔助)設備連接器safe guard net 護軍welding sparkles 焊接火花stratification logistics 辦後勤學orgnization Color management 顏色管理Visual management 目視管理hydraulic APCopper au 銅錐slide caliper 游標卡尺Angle compasses 角度規external diameter (內)外徑Micrometer 螺旋測微器 feeler gauge 原薄規Screw meter 東規(螺旋量規) Torque meter 扭力計Pushing－pulling force meter 推拉計Combination jig 組合治具Single jig 單個治具flow card 流程卡Arrow labels 箭頭標簽 rust－proof 防透油Lubricant 潤滑油Horizontal coordinate 橫座標Vertical coordinate 縱座標daily report sheet 目報表Topcovar 上(頂)蓋 server 伺服器Inspection defect :Mismatch 銷件deformation 變形Nyt 生銹peel 脫漆Shrink scratch 刮份Contamination 臟污screwbioken 刮痕Dent 凹痕water spots 水漬Gap 間隙label errorMissing label 漏貼 rejection criteria 拒收標准Suspater品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理PQC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B 模具正式投產前確認CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析8D 8 disciplines 8項回復內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小ACC Accept 允收REE Reject 拒收CR Critical 極嚴重的MAJ Major 主要的MIN Minor 輕微的AOQ Average Output Quality 平均出廠品質AOQL Average Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproductivity & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其它品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Ameliorate Notice 品質改善活動ADM Absolute Dimension Measurement 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Control Tools 品管七大手法通用之件類ECN Engineering Change Notes 工程變更通知(供應商)ECO Engineering Change Order 工程改動要求(客戶)PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範BOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面系統文件類QC Quality System 品質系統ES Engineering Standardization 工程標準CGOO China General PCE龍華廠文件H Houston (美國)休斯敦C Compaq (美國)康伯公司C China 中國大陸A Assembly 組裝(廠)S Stamping 沖壓(廠)P Painting 烤漆(廠)I Intel 英特爾公司T TAIWAN 臺灣IWS International Workman Standard 工藝標準ISO International Standard Organization 國際標準化組織GS General Specification 一般規格CMCS C-China M-Manufacture C-Compaq S-Stamping C ompaq產品在龍華衝壓廠製造作業規範CQCA Q-Quality A-Assembly Compaq產品在龍華組裝廠品管作業規範CQCP P-Painting Compaq產品在龍華烤漆廠品管作業規範部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manufacture Engineering 製造工程部PE Project Engineering 產品工程部A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Assembly 組裝(廠)S Stamping 沖壓(廠)生產類PCs Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料NHK North of Honking 中國大陸PRC People's Republic of China 中國大陸U.S.A the United States of America 美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量VS 以及REV Revision 版本JIT Just In Time 零庫存I/O input/output 輸入/輸出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electric-static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk read-only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CA V Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS'Y Assembly 裝配,組裝MAT'S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requirement 周出貨需求C/T Cycle Time 制程周期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer, Communication, Consumer electronics 消費性電子5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, message4MIH Man, Material, Money, Method, Time 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetic Inspect 高磁測試FMI Frequency Modulation Inspect 高頻測試B/M Board/molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complementary Metal Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數字助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Cable 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeIFIR (Dell Factory reject )LRR Line Reject RateSQE supplier Quality EngiweerDFM Desisw for MaFMEA Falwce modes andCIP ContinuousGVI CieBAC Vevtieal Intisntors VCA Value Cmeuin Qnaliryr ISR Initial Snapple ripestPSU Rowe’s SurlyFGI Forested Goal Inveatory NBE = Note Book EnclosureMPE = Mobilephone Enclosure Foxcavity = HZ = Hong ZhuiMG = maghasFoxconn = HonhaiNEW = wet work EndorserECG = electrical commercial。
汽车冲压部件中英对照表
英文名称 INSTALL ASSY PANEL PILLAR DOOR HOOD stringer mennber Cross mennber BRACE BRACKET HINGE BULKHEAD REINF FLOOR lower LH RH Front Rear inner FR DR RR DR F/FLR R/FLR BAR S-IMPACT RR DR BAR FR END UPR BEAM RR BPR INR BEAM RR BPR OTR BRACE RR SHELF LH BRACE RR SHELF RH BRACE RR. FLOOR SIDE LH BRACE RR. FLOOR SIDE RH BRACE S/MBR TO FRT FLOOR LH BRACKET HOOD RELEASE (LHD) BRACKET RR FLOOR SEAT MTG LH BRACKET RR FLOOR SEAT MTG RH BRK S-IMPACT RR FR DR LH BRKT ANTI ZIPPER LH BRKT BUMPER BRKT CTR BPR MTG BRKT FASCIA MTG BRKT FENDER LWR LH 缩写 中文名称 安装 总成 板 柱 门 盖 纵梁 横梁 支柱 支架 铰链 隔板 加强板 地板 上部 下部 左侧 右侧 前侧 后侧 外侧 内侧 前门 后门 前地板 后地板 后门侧防撞杆 散热器上横梁 后保防撞梁内板 后保防撞梁外板 后行李箱隔板左侧支柱 后行李箱隔板右侧支柱 后地板左边支柱 后地板右边支柱 前纵梁与前地板左连接板 发罩拉索支架 左后座椅安装支架 右后座椅安装支架 前门防撞杆后支架 前地板与门槛内板左连接板 前保险杠支架 后保险杠中部支架 保险杠安装支架 左侧前轮挡泥板下部支架
汽车制造专业英语词汇大全
.汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan = enterpriseexpansion projects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to.registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those ofNHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCT ools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact DiskRead-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Mea surement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable) C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AIDManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具split mold 双并式模具sprueless mold 无注道残料模具sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套manifold block 歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ringgate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton骨架slag riser 冒渣口slide(slide core)滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweeptemplete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindricalmachine 内圆磨床jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal toolgrinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语。
汽车冲压件---英文名称
19
后地板前部本体
REAR-FRONT-FLOOR
20
左前纵梁外板
FRONT-OUTER-RAIL-LH
21
右前纵梁外板
FRONT-OUTER-RAIL-RH
22
左前纵梁后部内连接板
FRONT-RAIL-EXTENSION-INNER-BRKT-LH
23
右前纵梁后部内连接板
FRONT-RAIL-EXTENSION-INNER-BRKT-RH
116
雨刮安装支架
WIPER-SUPPORT-BRACKET
117
前挡板下加强梁
FRONT-LOWER-CROSSMEMBER
118
前风挡下横梁
COWL-BAR-PANEL
119
空气室加强板
COWL-BAR-EXTENSION
120
排水槽本体
UPPER-DASH-PANEL
121
空调安装支架
DASH-PANEL-UP-HVAC-BRACKET
65
前保右安装盒上板
66
前保左安装下板
67
前保右安装盒下板
68
后保防撞横梁固定板
69
前拖车钩支架
70
后保左安装盒上板
71
后保右安装盒上板
72
后保左安装盒下板
73
后保右安装盒下板
74
换档手柄安装支架
75
手制动前安装支架
76
然油箱中加强板
77
后部横梁
78 左前纵梁后部外连接板下板
79 右前纵梁后部外连接板下板
99
行李箱缓冲块支架
DECKLID-STOP-BRACKET-POSITIONED
组装、冲压、喷漆等专业英语词汇
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫?si| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床?planer |'pleinmiller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' n|氧化?ksi'deiscratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良mp|镶块ùembeded lump|in'bed| |lfeeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catchadjustable spanner 活动扳手angle cutter 角铣刀anvil 铁钻arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板。
机械类常用英语 (组装、冲压、喷漆等专业词汇)
机械类常用英语(组装、冲压、喷漆等专业词汇) ---1Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床 planer |'pleinmiller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良n|氧化 oxidation |' ksi'deiscratch刮伤机械类常用英语(组装、冲压、喷漆等专业词汇) ---2dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产机械类常用英语(组装、冲压、喷漆等专业词汇) ---3equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑。
汽车冲压件中英文名称对照表
PANEL B PILLAR INNER LH 左侧B柱内板
PANEL B PILLAR INNER RH 右侧B柱盖板
PANEL B PILLAR INNER RH 右侧B柱内板
PNL RR DR INR LH 左后门内板
PNL RR DR INR RH 右后门内板
BRACKET RR FLOOR SEAT MTG LH 左后座椅安装支架
BRACKET RR FLOOR SEAT MTG RH 右后座椅安装支架
BRK S-IMPACT RR FR DR LH 前门防撞杆后支架
BRKT ANTI ZIPPER LH 前地板与门槛内板左连接板
BRKT FENDER UPR LH 左侧前轮挡泥板上部支架
BRKT FENDER UPR RH 右侧前轮挡泥板上部支架
BRKT FOOT REST (LHD) 踏脚板支架
BRKT GLS GUIDE DOOR 玻璃导轨支架
BRKT S-IMPACT CTR FR DR 前门防撞杆中支架
PNL FR DR INR RH 右前门内板
PNL FR DR OTR LH 左前门外板
PNL FR DR OTR RH 右前门外板
PNL FUEL FILLER DR 加油口盖外板
PNL HOOD INR 发罩内板
PNL HOOD OTR 发罩外板
PANEL SPRING HOUSE LH 左前悬挂支座下板
PANEL SPRING HOUSE RH 右前悬挂支座下板
PANEL COWL TOP OTR 空气盒外板
PANEL DASH (LHD) 前围挡板
汽车行业用语-中英文
Systems 系统-- Dies -模具-- In-house stamping parts(22) - 自制冲压件(25个) other stampings 其他沖壓件Jack / Tools 千斤顶/工具Door Trim Panel 门内饰板Headlining 顶盖内衬Carpet 地毯Package Tray 后置物板NVH - Insulator / Deadener 消音/ 减震隔热垫Deadner 沥青地毯- Instrument Panel -仪表台板- Console 副仪表台- Bumpers / Facia -保险杆- Front End Molding (GOR) " - 车前塑料件(水箱护板）"Interior / Exterior Plastics - 内外饰塑料件- A, B, C Pillar Trim & Scuff Plate 前中后立柱饰版&車門框版" - Exterior Ornamentation- Painted / Chromed Plastic" "- 外饰件- 车身色/镀鉻件"Decal, Badge 标牌/贴纸VIN PLATE 铭牌-- Grille 散熱器护柵-- Body Side Molding 车身防擦条roof moudling 车顶饰条belt line moulding 水切(车门饰条)- Fuel Filler Housing 加油管外套- Fuel Filler Door 加油门口Wheel Cover - 车轮盖Weather Strips for Doors 密封条- 车门Weather Strips for Glass (Run Channel) 密封条- 玻璃wheel housing -liner 鼓包内衬Mirror 后视镜Seats 座椅Glass 玻璃Door Module-Carry Plate 基版--门模塊(內飾)Window Regulator 玻璃升降机Door Latches 门锁Key Sets 锁芯Door Handle 门把手Decklid Handle 行李厢把手Hood Hinge & Decklid Hinge 发动机盖铰链、行李厢铰链Hood Latch & Decklid Latch 发动机盖锁、行李厢锁Window Wiper Motor & Link System (including Arm Blade) 雨刮电机及摇臂总成Washer System 雨刮清洗系统Sun Roof 天窗Bracket(Bumper Beam) -支架（保险杆加强秆）Air Bag 被动安全系统（气囊）Steering Wheel 方向盘Seat Belts 安全带mid to small plastic 中小塑件Overflow (Degas) 副水箱AC system 空调系统Fan & motor system 风扇电机总成Contol Assy-A/C (Manual) 空调控制器（手动）- Compressor 压缩机Radiator and Condenser assy 散热器/冷凝器总成Horn 电喇叭Head Lighting 前车灯Rear Lighting 尾灯Suspension Assy 前后悬挂总组-- Front/rear axle 前后橋-- Suspension Machining 悬挂加工件-- Stabilizer 稳定杆-- Coil Spring 园簧Front Suspension Assy 前悬挂总组- Stabilizer OD21 稳定杆OD21- Link (stabilizer) 连接杆(稳定杆)- Bushing (stabilizer) 衬套(稳定杆)- Clamp (stabilizer) 夹钳(稳定杆)- Cross member 横梁- Control arm ( including ball joints) 控制臂(含球窝接头)- Knuckle L/ R 转向节(左/右)- Hub Unit 轮毂总成- Strut/ shock absorber 减震器- Top mount 上支撐- Spring aid 弹簧座- Spring 弹簧- Gaitor 波纹防尘罩- Nut 螺母- Cover heat shield 隔热垫盖Rear suspension Assy 后悬挂总组- Crossmember 横梁- Rear Lower Assy Sub Assy 后悬下臂总成- Front Lower Arm 前悬下臂- Uper Lower Arm Assy 后上臂- Bump Stop 限位挡块- Spring 弹簧- Spring pad 弹簧垫块- Stabilizer 穏定杆- Bushing (stabilizer) 衬套(穏定杆)- Clamp (stabilizer) 夹箝- Pogostick Assy- Knuckle L/R 转向节(左/右)Hub Unit II 轮毂总成IIHub Unit Bearing 轮壳总成轴承Tire 轮胎Steel Wheels 铁圈Alloy wheels 铝轮圈Brakes 制动-- ABS Module ABS 模块- Booster & MC 真空助力器&总泵- Front caliper 前卡钳- Rear Caliper 后卡钳- Disc 盘式制动器- Dust shield 防尘罩- Drum Brake 鼓式制动器- Drum 鼓式制动器-- Brake / Fuel Lines 制动油管及燃油管Parking Lever 手刹- Parking Cable 驻车制动拉索Cables（MT）拉索（手排）Cables（AT）拉索（自排）Pedal Box 脚踏板Fuel Tank 油箱FDM 油泵Steering Gear Assy 转向机总成Steering Gear - HPAS 液压式转向机Steering Gear - EHPAS 电子液压转向机Steering Pump - HPAS 转向泵Steering Hose 转向油管Steering Column 方向机柱Steering Column Stalk Switch 组合开关Rotating Electrical Starter I4 / BZ(11000) 启动马达Rotating Electrical Alternator I4 / BZ(10300) 电机Clock Spring 转向簧圈Instrument Cluster 组合仪表Parking Sonar 倒车雷达Battery 电池Audio / CD 收放机/CDAntenna 天线Speaker 扬声器Spoiler 擾流板Wiring Harness 线束CANNISTER 碳罐Remote System (transmit/Receiver) 门锁遥控器(发射/接收) Switches 开关Engine Mounting 发动机支撑Air Induction System (AIS）-I4 进气系统(I4)Air Induction System (AIS）-BZ 进气系统(BZ)EMS (BZ ECU) 发动机管理系统(BZ ECU)EMS (I4 ECU) 发动机管理系统(I4 ECU)FEAD Brkt/belt 发电机支架/皮带（BZ）FEAD Brkt / tensioner 发电机支架/ 张紧轮（BZ）FEAD Brkt /idler 发电机支架/ 惰轮（BZ）FEAD Brkt/idler/belt 发电机支架/惰轮/皮带（I4）Driveshaft 传动轴Gear Shifter（Manual) 换档器(手动）Gear shift（Auto）换档器（自动）HOT END-Exhaust System 热端-排放系统COLD END-Exhaust System 冷端-排放系统Catalyst (BZ 催化剂(BZCatalyst (New I4 催化剂(New I4HINEGE(DOORS) 門鉸鍊DOOR CHECK ARM 车门限位器TYRE ASSEMBLY 车轮总成MIRROR CONTROL 后视镜控制器MOBILE LINK 手机通讯连接MANUAL 用户手册WARING TRIANGLE 三角回复反射器FIRE EXTINGUISHER 灭火器FUEL FILLING PIPE 加油管PWR STNG OIL COOLER 动力转向油冷却器Reservior 动力转向油壶MOULDING-Windshield/ DOOR MOULDING 风档导水槽，门上装饰盖WATER SHIELD 防水膜QUARTER WINDOW 三角窗WHEEL NUT 车轮螺母RUBBER HOSE 胶管PLATE ASY SPARE WHL 轮胎紧固螺栓Heater Control Panel & Gear Shifter Bezel 暖风控制面板、换档面板Fuel filter (Gasoline Strainer) 汽油滤清器Bumper Beam 保险杠横梁TOC(transmission oil cooler)Cooling hose/Lower Isolator 冷却水管Battery BoxCowl Grille 通风格珊Under cover 发动机防护板Cover Under 发动机防护罩Center Channel 玻璃滑槽Name Plate 铭牌HeatshieldFuel Filler CapSide Skirt 侧裙板Door Sash(Door Frame) 门框Stripe,Sash 门框膜-----------------------------Front Door Inner LH 前车门内板（左）Rear Door Outer RH 后车门外板（右）Rear Door Outer LH 后车门外板（左）Rear Door Inner RH 后车门内板（右）Rear Door Inner LH 后车门内板（左）Rear Floor 后地板B/S Outer RH 侧围外板（右）B/S Outer LH 侧围外板（左）B/S Inner RH 侧围内板（右）B/S Inner LH 侧围内板（左）Decklid Outer 行李箱盖外板Decklid Inner 行李箱盖内板Roof 顶盖Sun-Roof 顶盖（带天窗）Front Floor 前地板Front Fender RH 翼子板（右）Front Fender LH 翼子板（左）Hood Outer 发动机罩外板Hood Inner 发动机罩内板Front Door Outer RH 前车门外板（右）Front Door Outer LH 前车门外板（左）。
汽车外覆盖件冲压件零件标准名称中英文名称对照表-6页文档资料
[原创] 汽车冲压件中英文名称对照表英文名称中文名称INSTALL 安装ASSY 总成PANEL PNL 板PILLAR 柱DOOR DR 门HOOD 盖S/MBR 纵梁C/MBR 横梁BRACE 支柱BRACKET BRKT 支架HINGE 铰链BULKHEAD 隔板REINF 加强板FLOOR 地板UPR 上部LWR 下部LH 左侧RH 右侧FR 前侧RR 后侧OTR 外侧INR 内侧FR DR 前门RR DR 后门F/FLR 前地板R/FLR 后地板BAR S-IMPACT RR DR 后门侧防撞杆BAR FR END UPR 散热器上横梁BEAM RR BPR INR 后保防撞梁内板BEAM RR BPR OTR 后保防撞梁外板BRACE RR SHELF LH 后行李箱隔板左侧支柱BRACE RR SHELF RH 后行李箱隔板右侧支柱BRACE RR. FLOOR SIDE LH 后地板左边支柱BRACE RR. FLOOR SIDE RH 后地板右边支柱BRACE S/MBR TO FRT FLOOR LH 前纵梁与前地板左连接板BRACKET HOOD RELEASE (LHD) 发罩拉索支架BRACKET RR FLOOR SEAT MTG LH 左后座椅安装支架BRACKET RR FLOOR SEAT MTG RH 右后座椅安装支架BRK S-IMPACT RR FR DR LH 前门防撞杆后支架BRKT ANTI ZIPPER LH 前地板与门槛内板左连接板BRKT BUMPER 前保险杠支架BRKT CTR BPR MTG 后保险杠中部支架BRKT FASCIA MTG 保险杠安装支架BRKT FENDER LWR LH 左侧前轮挡泥板下部支架BRKT FENDER LWR RH 右侧前轮挡泥板下部支架BRKT FENDER UPR LH 左侧前轮挡泥板上部支架BRKT FENDER UPR RH 右侧前轮挡泥板上部支架BRKT FOOT REST (LHD) 踏脚板支架BRKT GLS GUIDE DOOR 玻璃导轨支架BRKT S-IMPACT CTR FR DR 前门防撞杆中支架BRKT S-IMPACT FR FR DR LH 前门防撞杆前支撑板BRKT S-IMPACT FR FR DR RH 前门防撞杆前支撑板BRKT S-IMPACT FR RR DR LH 左后门侧防撞杆前支架BRKT STRIKER 背门锁扣加强板BRKT SUPT S-IMPACT RR DR LH 左后门侧防撞杆支架BRKT SUPT S-IMPACT RR DR RH 右后门侧防撞杆支架BRKT UPR BUMPER MTG 保险杠安装上支架BRKT ENG MOUNT 发动机悬置支架BRKT SPRING HOUSE RH 右前悬挂上支座BRKT FUEL TANK COMMON 油箱安装左后支架BRKT TRAILING ARM INR LH 左后悬挂纵臂安装内支架BRKT TRAILING ARM INR RH 右后悬挂纵臂安装内支架BRKT TRAILING ARM OTR LH 左后悬挂纵臂外支架BRKT TRAILING ARM OTR RH 右后悬挂纵臂外支架BULKHEAD HINGE FRT LWR LH 左侧前门下部铰链加强板隔板BULKHEAD HINGE FRT LWR RH 右侧前门下部铰链加强板隔板BULKHEAD R/FLR S/MBR LH 后地板左纵梁隔板BULKHEAD R/FLR S/MBR RH 后地板右纵梁隔板BULKHEAD SILL 门槛隔板C/MBR BACKBONE 中央通道横梁C/MBR FR END OTR 散热器下横梁外板C/MBR R/FLR 后地板中横梁C/MBR R/SEAT 后地板前横梁下板C/MBR F/FLR LH 前地板左前横梁C/MBR F/FLR RH 前地板右前横梁C/MBR F/FLR RR LH 前地板左后横梁C/MBR FR END, INR CTR 散热器下横梁中内板C/MBR FR END, INR LH 散热器下横梁左内板CHNL GLS GUIDE FR FR DR LH 左前门玻璃导轨CHNL GLS GUIDE FR FR DR RH 右前门玻璃导轨CHNL GLS GUIDE FR RR DR LH 左后门玻璃导轨CHNL GLS GUIDE FR RR DR RH 右后门玻璃导轨CHNL GLS GUIDE RR FR DR RH 右前门后玻璃导轨CHNL GLS GUIDE UPR RR DR LH 左后门上玻璃导轨CHNL GLS GUIDE UPR RR DR RH 右后门上玻璃导轨EXT DASH PANEL LH 前围挡板左下板EXT DASH PANEL RH 前围挡板右下板EXT C/MBR R/FLR LH 后地板中横梁与纵梁左连接板FRAME FR UPR INR LH 左翼子板加强梁内板FRAME FR UPR INR RH 右翼子板加强梁内板FRAME FR UPR OTR LH 左侧翼子板上部边梁外板FRAME FR UPR OTR RH 右侧翼子板上部边梁外板FRONT S/MBR REAR LH 左前纵梁与地板纵梁连接板FRONT, S/MBR REAR RH 右前纵梁与地板纵梁连接板HINGE FUEL FILLER DR 加油口盖铰链HOOK, MUFFLER B/BONE 中央通道消音器挂钩PANEL A PILLAR LWR LH 左A柱下板PANEL A PILLAR LWR RH 右A柱下板PANEL AIR EXTRACTION BOX OTR LH 左侧排气盒外板PANEL AIR EXTRACTION BOX OTR RH 右侧排气盒外板PANEL B PILLAR INNER LH 左侧B柱盖板PANEL B PILLAR INNER LH 左侧B柱内板PANEL B PILLAR INNER RH 右侧B柱盖板PANEL B PILLAR INNER RH 右侧B柱内板PANEL BODY SIDE OTR LH 左侧围外板PANEL BODY SIDE OTR RH 右侧围外板PANEL CANTRAIL INNER LH 左侧上边梁内板PANEL CANTRAIL INNER RH 右侧上边梁内板PANEL COWL TOP INR (LHD) 空气盒内板PANEL EXT REAR FLR FRT 后地板前连接板PANEL EXT REAR FLR RR 后地板后加强板PANEL FRONT FENDER LH 左前翼子板PANEL FRONT FENDER RH 右前翼子板PANEL FRT HEADER LWR 顶盖前横梁下部板PANEL PILLAR FR INR LH 左A柱内板PANEL PILLAR FR INR LH 左侧A柱内板PANEL PILLAR FR INR RH 右A柱内板PANEL PILLAR FR INR RH 右侧A柱内板PANEL REAR FLOOR 后地板PANEL REAR SHELF 行李架隔板PANEL REINF FRT HINGE A PILLAR LH 左侧A柱铰链加强板PANEL REINF FRT HINGE A PILLAR RH 右侧A柱铰链加强板PANEL ROOF 顶盖PANEL ROOF BOW 顶盖中横梁PANEL RR END INR 后围内板PANEL RR END OTR 后围横梁外板PANEL RR HEADER UPR 顶盖后横梁上板PANEL RR QTR INR LWR LH 左后轮罩外板下段PANEL RR QTR INR LWR RH 右后轮罩外板下段PANEL RR QTR INR UPR LH 左后轮罩外板上段PANEL RR QTR INR UPR RH 右后轮罩外板上段PANEL RR. W/HSE INR LH 左轮罩内板PANEL RR. W/HSE INR RH 右轮罩内板PANEL SILL INR LH 前地板左门槛内板PANEL SILL INR LH 左门槛内板PANEL SILL INR RH 前地板右门槛内板PANEL SILL INR RH 右门槛内板PANEL SPRING HOUSE LH 左前悬挂支座下板PANEL SPRING HOUSE RH 右前悬挂支座下板PANEL COWL TOP OTR 空气盒外板PANEL DASH (LHD) 前围挡板PNL FR DR INR LH 左前门内板PNL FR DR INR RH 右前门内板PNL FR DR OTR LH 左前门外板PNL FR DR OTR RH 右前门外板PNL FUEL FILLER DR 加油口盖外板PNL HOOD INR 发罩内板PNL HOOD OTR 发罩外板PNL RR DR INR LH 左后门内板PNL RR DR INR RH 右后门内板PNL RR DR OTR LH 左后门外板PNL RR DR OTR RH 右后门外板PNL T-GATE INR 后背门内板PNL T-GATE OTR 后背门外板PNL TRUNK LID INR 行李箱盖内板PNL TRUNK LID OTR 行李箱盖外板PNL SPRING HOUSE LH 左后悬挂支座下板PNL SPRING HOUSE RH 右后悬挂支座下板REINF A PILLAR UPR LH 左侧A柱上部加强板REINF A PILLAR UPR RH 右侧A柱上部加强板REINF B PILLAR CTR LH 左B柱中加强板REINF B PILLAR CTR RH 右B柱中加强板REINF B PILLAR DOUBLER LH 左侧B柱铰链加强板REINF B PILLAR DOUBLER RH 右侧B柱铰链加强板REINF B PILLAR LH 左侧B柱加强板REINF B PILLAR RH 右侧B柱加强板REINF B PILLAR UPR LH 左侧B柱加强上段REINF B PILLAR UPR RH 右侧B柱加强上段REINF BRACE REAR SHELF LH 行李箱隔板左托架支柱REINF BUMP STOP RH 右侧缓冲器加强板REINF BUMPER STAY LH 后保险杠左缓冲支柱加强板REINF BUMPER STAY RH 后保险杠右缓冲支柱加强板REINF COWL TOP INR (LHD) 转向柱加强板REINF DASH PANEL CTR 前围挡板下加强板REINF DOOR CHECK LH 左侧前门限位器加强板REINF FR END C/MBR SIDE LH 散热器下横梁左侧加强板REINF FRAME UPR FR DR LH 左前门窗框加强板REINF FRAME UPR FR DR RH 右后门窗框加强板REINF FRAME UPR FR DR RH 右前门窗框加强板REINF FRAME UPR RR DR LH 左后门窗框加强板REINF FUEL FILLER DR 加油口盖加强板REINF HINGE FRT UPR LH 左侧前门上部铰链加强板REINF HINGE FRT UPR RH 右侧前门上部铰链加强板REINF HINGE RR DR LH 左后门铰链加强板REINF HINGE RR DR RH 右后门铰链加强板REINF HINGE T-LID LH 行李箱盖铰链左加强板REINF HINGE T-LID RH 行李箱盖铰链右加强板REINF HOOD HINGE LH 发动机罩左侧铰链加强板REINF LATCH FR DR LH 左前门锁加强板REINF LATCH FR DR RH 右前门锁加强板REINF LATCH RR DR RH 右后门锁加强板REINF REAR SHELF FRONT 行李架前加强板REINF SBELT SIDE LH 左前座安全带左下加强板REINF SBELT SIDE RH 左前座安全带左下加强板REINF SILL LH 左侧门槛加强板REINF SILL RH 右侧门槛加强板REINF STG COL BRKT (LHD) 转向柱支架REINF WAIST OTR RR DR RH 右后门窗沿外加强板REINF BACKBONE 中央通道加强板REINF ENG MOUNT 发动机悬置加强板REINF FR END C/MBR 散热器下横梁加强板REINF FR S/MBR INR, FR LH 左前纵梁内板前加强板REINF FR S/MBR INR, FR RH 右前纵梁内板前加强板REINF FR S/MBR INR, RR LH 左前纵梁内板后加强板REINF FR S/MBR OTR LH 左前纵梁外板加强板REINF FR S/MBR OTR REAR LH 左前纵梁外板后加强板REINF FR S/MBR OTR REAR RH 右前纵梁外板后加强板REINF FRT S/MBR, REAR LH 左前纵梁地板纵梁加强板REINF T/M MOUNT 变速箱悬置加强板REINF DASH PANEL (LHD) 前围挡板内加强板REINF R/FLR LH 后地板左加强板REINF R/FLR RH 后地板右加强板REINF C/MBR UPR LH 后地板前横梁下板左加强板REINF C/MBR UPR RH 后地板前横梁下板右加强板REINF R/FLR S/MBR FR LH 后地板左纵梁加强板REINF R/FLR S/MBR FR RH 后地板右纵梁加强板REINF R/FLR S/MBR LH 后地板左纵梁侧加强板REINF R/FLR S/MBR RH 后地板右纵梁侧加强板REINF S/BELT R/FLR 后座椅安全带内加强板S/MBR FR FLR LH 前地板左纵梁S/MBR FR FLR RH 前地板右纵梁S/MBR FR INR LH 左前纵梁内板S/MBR FR INR RH 右前纵梁内板S/MBR FR OTR LH 左前纵梁外板S/MBR FR OTR RH 右前纵梁外板SHIELD FR FENDER LH 左前挡泥板SHIELD FR FENDER RH 右前挡泥板SMBR RR FLR LH 后地板左纵梁SMBR RR FLR RH 后地板右纵梁SUPT R/FLR S/MBR LH 后地板左纵梁支架。
汽车制造专业英语词汇大全
汽车制造专业英语词汇大全YUKI was compiled on the morning of December 16, 2020汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver 电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch ofSPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resourcedepartment人力资源部productiondepartment生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler andstraightener整平机punching machine冲床gripper机械手hydraulic machine油压机lathe车床planer|'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=revitingmachine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director 部长deputy manager |=vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长groupleader/supervisor组长line supervisor线长assistant manager 助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to returnmaterial/stock to退料scraped|'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufactureprocedure制程deficientmanufacturingprocedure制程不良oxidation |'ksi'dein|氧化scratch刮伤dents压痕defective upsidingdown抽芽不良defective to staking铆合不良feeding is not inplace送料不到位stamping-missing漏冲education andtraining教育与训练proposalimprovement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=platepinch压板bolt螺栓administration/general affairs dept总务部automaticscrewdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective productlabel不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) withexposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver 起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is alittle bigger尺寸偏大(小)slippedscrewhead/slipperyscrew head螺丝滑头slippedscrewhead/shipperyscrew thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surfaceprocessing表面处理exposed metal/baremetal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan =enterprise expansionprojects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products 良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffleplate; barricade隔板carton box纸箱to pull and stretch拉深to put material inplace, to cut material,to input落料to impose lines压线to compress,compressing压缩to feed, feeding送料transportation运输(be)qualfied, up tograde合格not up to grade, notqualified不合格material change,stock change材料变更feature change 特性变更evaluation评估prepare for, makepreparations for 准备parameters参数rotating speed,revolution转速manufacturemanagement制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufactureprocedure制程operation procedure作业流程to revise, modify修订to switch over to,switch---to throw--over switching over切换engineering, projectdifficulty工程瓶颈automation自动化to stake, staking,reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieingout press冲床uncoiler &strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver交货to return delivenry to. registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance =receive验收to notice通知application form forpurchase请购单consume,consumption消耗to fill in填写abrasion磨损reverse angle =chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a dieplate移走模板easily damagedparts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabularyfor die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blankingdie冲裁模progressive die,follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=sidecut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, linepulling线拉伸engraving, toengrave刻印upsiding downedges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supportingblank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location 手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physicalinvetory secondcount 复盘点数量quantity of customscount会计师盘,点数量the first page第一联filed by accountingdepartment forreference会计部存查end-user/usingunit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet andphysical inventorylist will be sent toaccountingDepartment together(Those of NHK willbe sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application statusrecords of year-endphysical inventoryList andphysical inventorycard 年终盘点卡与清册使用－状况明细表blank and wastesheet NO.空白与作废单号plate电镀mold成型material forengineering moldtesting工程试模材料sample样品incoming material tobe inspected进货待验description品名steel/rolled steel钢材Material statisticssheet物料统计明细表meeting minutes会议记录meeting type 会别distributiondepartment分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsibledepartment负责单位pre-fixed finishingdate预定完成日approved by /checked by /prepared by核准/审核/承办PCE assemblyproduction schedulesheetPCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physicalinventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical countquantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finishedproduct半成品packing materials包材goodproduct/acceptedgoods/ acceptedparts/good parts良品defectiveproduct/non-goodparts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physicalinventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punchhead挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round piercepunch=die button圆冲子shape punch=dieinsert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speedtransmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speedsteel钨高速的moly high speedsteel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw 内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-heightsleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block forlocation定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulationmolding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=~w=L=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=~diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ~Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE qualityengineering 品质工程人员品质保证类FAI first articleinspection 新品首件检查TVR tool verificationreport 模具确认报告3B 3B 模具正式投产前确认CP capability index能力指数CPK capabilityindex of process 模具制程能力参数SSQA standardizedsupplier quality 合格供应商品质评估OOBA out of boxaudit 开箱检查QFD qualityfunction deployment品质机能展开FMEA failure modeleffectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR correctiveaction request 改正行动要求corrective actionreport 改正行动报告FQC运作类AQL AcceptableQuality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ AverageOutput Quality 平均出厂品质AOQL AverageOutput Quality Level平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number料号L/N Lot Number 特采AOD Accept OnDeviation 特采UAI Use As It 首件检查报告FPIR First PieceInspection Report百万分之一SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Rep eatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency频率N Number 样品数其它品质术语类QCC QualityControl Circle 品质圈QIT QualityImprovement Team品质改善小组PDCA Plan DoCheck Action 计划执行检查总结ZD Zero Defect 零缺点QI QualityImprovement 品质改善QP Quality Policy目标方针TQM Total QualityManagement 全面品质管理MRB MaterialReject Bill 退货单LQL Limiting QualityLevel 最低品质水准RMA ReturnMaterial Audit 退料认可QAN QualityAmelionrate Notice品质改善活动ADM AbsoluteDimensionMeasuremat 全尺寸测量QT Quality Target品质目标7QCTools 7 QualityControll Tools 品管七大手法通用之件类ECN EngineeringChange Notes 工程变更通知(供应商)ECO EngineeringChange Order 工程改动要求(客户)PCN ProcessChange Notice 工序改动通知PMP ProductManagement Plan生产管制计划SIP Specification InProcess 制程检验规格SOP 开始生产IS InspectionSpecification 成品检验规范PS PackageSpecification 包装规范SPEC Specification规格DWG Drawing 图面系统文件类QC Quality System品质系统ES EngineeringStandarization 工程标准CGOO ChinaGeneral PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂) I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMC Production &Material Control 生产和物料控制PPC ProductionPlan Control 生产计划控制MC Material Control物料控制ME ManafactureEngineering 制造工程部PE ProjectEngineering 产品工程部A/C AccountantDept 会计部DC DocumentCenter 资料中心QE QualityEngineering 品质工程(部)QA QualityAssurance 品质保证(处)QC Quality Control品质管制(课)PD ProductDepartment 生产部LAB Labratry 实验室IE IndustrialEngineering 工业工程R&D Research &Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO PurchasingOrder 采购订单MO ManufactureOrder 生产单D/C Date Code 生产日期码ID/C IdentificationCode (供应商)识别码SWR Special WorkRequest 特殊工作需求L/N Lot Number 批号P/N Part Number料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆the United Statesof America 美国E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-staticDischarge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian上午PM Post Meridian下午CD Compact Disk光碟CD-ROM CompactDisk Read-OnlyMemory 只读光碟FDD Floppy DiskDrive 软碟机HDD Hard DiskDrive 碟碟机REF Reference 仅供参考CONN Connector连接器CAV Cavity 模穴CAD Computer AidDesign 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit集成电路T/P True Position真位度TYP Type 类型WDR WeeklyDeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time标准时间P/M Product Market产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/MBoar/Molding(flat cable) C/P Connector ofPCA/P AssemblySPS Switchingpower supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital VedioDiskVCD VdeioCompact DiskLCD Liquid CrystalDisplayCAD Computer AIDDesignCAM Computer AIDManufacturingCAE Computer AIDEngineeringABIOS AchancedBasic in put/outputsystem 先进的基本输入/输出系统CMOSComplemeruaryMetoll OxideSemiconductor 互补金属氧化物半导体PDA PersonalDigital Assistant 个人数字助理IC Integrated Circuit集成电路ISA IndustryStandardArchitecture 工业标准体制结构MCA Micro ChannelArchitecture 微通道结构EISA ExtendedIndustry StandardArchitecture 扩充的工业标准结构SIMM Single in-linememory module 单项导通汇流组件DIMM Dual in-lineMemory Module 双项导通汇流组件LED Light-EmittingDiode 发光二级管FMEA Failure ModeEffectivenes 失效模式分析W/H Wire Harness金属线绪束集组件F/C Flat Calle 排线PCB Printed CircuitBoard 印刷电路板CAR CorrectionAction Report 改善报告NG Not Good 不良WPR WeeklyDeliveryRequirement 周出货要求PPM Parts PerMillion 百万分之一TPM TotalProductionMaintenance 全面生产保养MRP MaterialRequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸 powder forming 粉末成形calendaring molding压延成形 powdermetal forging 粉末锻造cold chamber diecasting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding粉末压出成形rocking die forging摇动锻造compound molding复合成形 rotaryforging 回转锻造compressionmolding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulationmolding 注入成形sand mold casting砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow)molding 中空(吹出)成形squeeze casting 高压铸造hot chamber diecasting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting精密铸造 matcheddie method 对模成形法laminating method被覆淋膜成形 lowpressure casting 低压铸造lost wax casting 脱蜡铸造 matchedmould thermalforming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold有肩柱塞式模具shoe mold 料套式模具center-gated mold中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模offswt bending die双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavityplate 复板模 positivemold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具 prototypemold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing)压花起伏成形re-entrant mold 倒角式模具runless injectionmold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positivemold 半全压式模具shaper 定型模套single cavity mold 单腔模具split mold 双并式模具 sprueless mold 无注道残料模具sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimmingdie 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke typedie 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢 dowelhole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machinedplate 角形模板 finishmachined roundplate 圆形模板fixed bolster plate 固定侧模板 flanged pin带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid整体模蕊盒 hosenippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate可动侧模板 onepiece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide穴型导板peened head punch镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch顶挤冲头 punch 冲头puncher 推杆 pusherpin 衬套梢rack 机架 rappingrod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lockpin 流道拉梢screw plug 头塞 setscrew 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴 sprue注道sprue bushing 注道衬套 sprue bushingguide 注道导套sprue lock bushing注道定位衬套spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱stripper bolt 脱料螺栓。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
SUSP-ARM-FIX-REINF REAR-FRONT-SUBFRAME-ATTACH-BRKT-LH REAR-FRONT-SUBFRAME-ATTACH-BRKT-RH REAR-BACK-SUBFRAME-ATTACH-BRACKET REAR-BACK-SUBFRAME-ATTACH-BRACKET ISO-FIX-BRACKET SUBFRAME-ATTACH-REINFORCEMENT-LH SUBFRAME-ATTACH-REINFORCEMENT-RH FRONT-RAIL-ATTACH-BRACKET-LH FRONT-RAIL-ATTACH-BRACKET-RH FRONT-BEAM-BUMPER FRONT-UPPER-CRASH-BOX-LH FRONT-UPPER-CRASH-BOX-RH FRONT-LOWER-CRASH-BOX-LH FRONT-LOWER-CRASH-BOX-RH REAR-RAIL-ATTACH-BRACKET FRONT-TOW-HOOK-BRACKET REAR-UPPER-CRASH-BOX-LH REAR-UPPER-CRASH-BOX-RH REAR-LOWER-CRASH-BOX-LH REAR-LOWER-CRASH-BOX-RH GEARBOX-LEVER-FIX-BRACKET FRONT-HANDBRAKE-FIX-BRACKET CENTRAL-FUEL-TANK-REINF REAR-RAIL-CROSSMEMBER FRONT-RAIL-EXTENSION-LOWER-BRKT FRONT-RAIL-EXTENSION-LOWER-BRKT-RH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
左前纵梁前部内板 右前纵梁前部内板 后悬安装支架 左前纵梁加强板 右前纵梁加强板 发动机左悬置加强板 发动机右悬置加强板 左前纵梁后部本体 右前纵梁后部本体 后纵梁左连接板 后纵梁右连接板 后悬弹簧固定座 左后纵梁本体 右后纵梁本体 后悬弹簧固定座加强板 左后纵量侧盖板 右后纵量侧盖板 左后纵梁后部 右后纵梁后部 后制动油管支架 后保横梁安装板 油箱左安装板 油箱右安装板 油管左后固定支架 油管右后固定支架 油管左后固定支架加强板 油管右后固定支架加强板
FRONT-RAIL-EXTENSION-UPPER-BRKT-LH FRONT-RAIL-EXTENSION-UPPER-BRKT-RH FRT-RAIL-EXTENS-LOWER-BRKT-REINF-LH FRT-RAIL-EXTENS-LOWER-BRKT-REINF-RH REAR-INNER-RAIL-REINFORCEMENT-LH REAR-INNER-RAIL-REINFORCEMENT-RH REAR-RAIL-EXTENSION-REINF-LH REAR-RAIL-EXTENSION-REINF-RH REAR-BEAM_BUMPER REAR-TOW-HOOK-BRACKET CENTRAL-TUNNEL WHEEL-FIX-BRACKET CENTRAL-FLOOR-LH CENTRAL-FLOOR-RH CENTRAL-FRAME-BRACKET-LH CENTRAL-FRAME-BRACKET-RH FRONT-BRAKE-TUBE-FIX-BRACKET-LH FRONT-BRAKE-TUBE-FIX-BRACKET-RH RR-END-PANEL-OUTER DECKLID-STOP-BRACKET-POSITIONED RR-END-PANEL-INNER-W-O-REINF DECKLID-LATCH CENTER-DASHBOARD-BRACKET HVAC-PROTECTION UPPER-DASH-PANEL-CROSS-BRACKET UPPER-DASH-PANEL-CROSS-BRACKET-RH UPPER-DASH-PANEL-REINF-LH
汽车冲压件中英文名称对照
序号 中文ห้องสมุดไป่ตู้称
前底板左纵梁 前底板右纵梁 前底板左纵梁加强板 前底板右纵梁加强板 左前座椅横梁 右前座椅横梁 后地板后部本体 中通道前加强板 手制动后安装支架 座椅左内安装支架 座椅右内安装支架 座椅左安装支架 座椅右安装支架 座椅侧安装板 座椅左内安装加强板 座椅右内安装加强板 后底板前横梁 后地板前部加强板 后地板前部本体 左前纵梁外板 右前纵梁外板 左前纵梁后部内连接板 右前纵梁后部内连接板 左前纵梁后部本体加强板 右前纵梁后部本体加强板
UPPER-DASH-PANEL-REINF-RH LOWER-DASH-PANEL-CROSSMEMBER-BRKT LOWER-DASH-PANEL-CROSSMEMBER-BRKT HEAD-LAMP-BACK-UPPER-CROSSM-LH HEAD-LAMP-BACK-UPPER-CROSSM--RH UPPER-DASH-PANEL-CROSSMEMBER FRONT-BEAM-BUMPER-ATTACH-BRACKET-LH FRONT-BEAM-BUMPER-ATTACH-BRACKET-RH OIL-TANK-BRACKET WIPER-SUPPORT-BRACKET FRONT-LOWER-CROSSMEMBER COWL-BAR-PANEL COWL-BAR-EXTENSION UPPER-DASH-PANEL DASH-PANEL-UP-HVAC-BRACKET HEAD-LAMP-SIDE-PANEL-ASM-LH HEAD-LAMP-SIDE-PANEL-ASM-RH HEAD-LAMP-SIDE-PNL-LWR-BRKT-LH HEAD-LAMP-SIDE-PNL-LWR-BRKT-RH DASHBOARD-SUPP-BRACKET-LH DASHBOARD-SUPP-BRACKET-RH-ASM DASH_PANEL-PLATE DASH_PANEL DASH-PANEL-REINFORCEMENT-LH DASH-PANEL-REINFORCEMENT-RH BATTERY-BRACKET-REAR-FIXING FOOTREST-BRACKET-LH
FRONT-INNER-RAIL-LH FRONT-INNER-RAIL-RH REAR-LOWER_SUBFRAME_BRACKET FRONT-RAIL-REINFORCEMENT-LH FRONT-RAIL-REINFORCEMENT-RH ATTACH-ENGINE-REINFORCEMENT-LH ATTACH-ENGINE-REINFORCEMENT-RH FRONT-RAIL-EXTENSION-LH FRONT-RAIL-EXTENSION-RH REAR-RAIL-CROSSMEMBER-BRACKET-LH REAR-RAIL-CROSSMEMBER-BRACKET-RH REAR-SUSPENSION-SPRING-ATTACHMENT REAR-RAIL-LH REAR-RAIL-RH REAR-SUSPENSION-ATTACH-REINFORCEMENT REAR-RAIL-LATERAL-COVER-LH REAR-RAIL-LATERAL-COVER-RH REAR-RAIL-EXTENSION-LH REAR-RAIL-EXTENSION-RH REAR-BRAKE-TUBE-FIX-BRACKET REAR-BEAM-BUMPER-ATTACH-BRACKET FUEL-TANK-FIX-REINF-LH FUEL-TANK-FIX-RENINF-RH REAR-WEB-BRACKET-LH REAR-WEB-BRACKET-RH REAR-WEB-BRACKET-REINFORCEMENT-LH REAR-WEB-BRACKET-REINFORCEMENT-RH
53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
后悬挂臂加强板 左后纵梁前支架 右后纵梁前支架 左后纵梁后支架 右后纵梁后支架 固定支架 左后纵梁加强板 右后纵梁加强板 前保盒左固定板 前保盒右固定板 前保横梁本体 前保左安装盒上板 前保右安装盒上板 前保左安装下板 前保右安装盒下板 后保防撞横梁固定板 前拖车钩支架 后保左安装盒上板 后保右安装盒上板 后保左安装盒下板 后保右安装盒下板 换档手柄安装支架 手制动前安装支架 然油箱中加强板 后部横梁 左前纵梁后部外连接板下板 右前纵梁后部外连接板下板
英文名称 LOWER-CENTRAL-FLOOR-RAIL-LH LOWER-CENTRAL-FLOOR-RAIL-RH LOWER-FLOOR-RAIL-REINF-LH LOWER-FLOOR-RAIL-REINF-RH FRONT-SEAT-CROSSMEMBER-LH FRONT-SEAT-CROSSMEMBER-RH REAR-BACK-FLOOR FRONT-TUNNEL-REINFORCEMENT REAR-HANDBRAKE-FIX-BRACKET INNER-ATTACH-SEAT-BRACKET-ASM-LH INNER-ATTACH-SEAT-BRACKET-ASM-RH SIDE-ATTACH-SEAT-BRACKET-LH SIDE-ATTACH-SEAT-BRACKET-RH SIDE-ATTACK-SEAT-REINF INNER-ATTACK-SEAT-REINF-LH INNER-ATTACK-SEAT-REINF-RH REAR-FLOOR-CROSSMEMBER REAR-FRONT-FLOOR-REINFORC REAR-FRONT-FLOOR FRONT-OUTER-RAIL-LH FRONT-OUTER-RAIL-RH FRONT-RAIL-EXTENSION-INNER-BRKT-LH FRONT-RAIL-EXTENSION-INNER-BRKT-RH FRONT-RAIL-EXTENSION-REINF-LH FRONT-RAIL-EXTENSION-REINF-RH