通讯系统操作维护手册(dsc60)

合集下载

通讯系统操作维护手册(dsc60)

MF/HF DSC设备操作手册(Model: DSC-60)渤海石油通讯网络公司编制控制面板，LED描述◆控制面板菜单说明：按键及指示灯功能Power 开关电源DISTRESS 按下并持续3秒钟以上就可以发送遇险警告。

刚开始按下时闪烁，按住超过3秒钟以后常亮。

在船收到遇险确认信息前此灯一直常亮。

按此键的时间少于3秒钟，DSC-60不会发出遇险警告。

CALL 除遇险警告外的呼叫Cursor Pad 选择菜单；调整音量大小。

（遇险或紧急告警以最大音量接收，不受扬声器控制。

）ENT 记录按键的输入CANCEL ●取消错误数据●返回上一级菜单●返回到DSC待机屏幕●关闭告警音●取消发射，打印●消除错错误信息1/RT/2182 ●从DSC待机屏幕转到无线电话的设置屏幕●在无线电话设置界面下，按下此键持续2秒以上转到2182.0kHz/J3E2/DSC 从无线电话的设置屏幕转到DSC待机屏幕3/TEST 每日检测4/IntCom 开关与无线电话间的通讯5/ACK 切换手动/自动确认功能6/SCAN 开始/停止在DSC待机界面下对DSC常规频率的扫描。

7/ ●扬声器开关●关闭蜂鸣器注意此键不能关闭遇险或紧急告警8/PRINT 打印通讯日志文件，当前屏幕（除DSC待机屏幕和无线电话设置屏幕外）和测试结果9/调节键盘/LCD背景屏幕亮度和对比度*/FILE ●在DSC待机界面下打开发送的消息文件以便发送●当准备一个0/LOG 在DSC待机界面下打开TX/RX日志文件#/SETUP 在DSC待机界面下打开设置菜单ALARM灯●遇险或紧急呼叫时以红色闪烁●安全或常规呼叫时以绿色闪烁（更快）OVEN 灯电源打开时点亮当船舶上的生命遇到危险的时候，请按照下面的流程操作：1．掀开DISTRESS 按钮的盖板，按住[DISTRESS]按钮至少3秒钟显示下面的信息后，松开[DISTRESS]按钮。

2．遇险呼叫发射后会出现下面的显示。

通信系统维护手册

贵州发耳电厂4×600M W机组通信系统维护手册批准:复审:初审：编制：王建海贵州金元发电运营有限公司发耳分公司二○一○年一月通信系统维护手册1.Coral数字程控用户交换机1.1.C oral数字程控交换机的硬件维护1.1.1.机柜维护检查1)机柜安装牢固平稳，没的振动摇动现象。

2)机柜完好，柜门开关正常。

3)机柜接地完好。

4)保持机柜及设备清洁，防止灰尘沉积。

1.1.2.Coral数字程控交换机的板卡检查1)各板卡指示正常，没有告警信号。

2)各板卡的温度正常，没有过热现象。

3)板卡无松动现象，固定螺钉紧固。

4)如果怀疑卡板有故障，可尝试重新插拔。

1.1.3.Coral数字程控交换机用户接线维护1)Coral数字程控交换机卡板的电话号码均已引接到MDF配线架上的机侧，并按顺序排列。

2)用户电话线是用电缆引接到MDF配线架上的用户侧（保安侧）。

3)用户电话与Coral数字程控交换机卡板的电话号码用跳线连接。

4)跳线时要正确使用卡刀，将跳线卡牢固，并注意布线整齐美观。

5)平时检查配线架的接线没有松脱现象。

1.2.C oral数字程控交换机的软件维护Coral系统的所有软件设置，都是通过与交换机相连的维护终端来进行的。

采用菜单选择方式和命令行方式进行操作，并且提供了全部功能的缺省设置，用户只需根据具体情况修改软件设置就可符合实际需要，而不必全部重新更改软件设置。

编程接口（PI）数据终端的串行口可以和MSX、MEX、MCP卡上的串行口相连，也可以和RMI、8DRCM（F）卡上的3个串行口的任意一个相连，还可以和RMI、8DRCM（F）卡内部Modem相连，此时用Modem可以进行遥控监测和远端维护。

1.2.1.维护终端的连接维护终端与交换机进行串行通信时（RS232），可作如下连接：电脑端COM口为9针母头交换机端KB0口为9针母头电脑端针脚针脚交换机端发TX 2------------------------------ 3 RX收收RX 3-------------------------------2 TX发地GND 5-------------------------------5 GND地如果需要从8DRCM（F）的其它KB口连接维护或计费连线时，可做如下连接：电脑端COM口为9针母头 8DRCM（F）卡板出线（KB1、KB2或KB3）电脑端针脚配线架资料发TX 2-------------------------------- RX收收RX 3-----------------------------------TX发地GND 5------------------------------------GND地（KB1、KB2和KB3共用）1.2.2.进入维护终端计算机的开始→程序→附件→通讯→超级终端运行超级终端，输入该连接的名字，然后设置选择连接时使用是通过COM口还是调制解调器连接。

FURUNO DSC-60 MF HF DSC Watch Receiver 说明书

Model DSC-60Catalogue No. W-3241cMF/HF DSC/Watch Receiverq Fully meets GMDSS carriage requirements q Distress, safety and routinecommunicationsq Scanning of DSC frequencies for distressand general calls on MF/HFq Excellent readability of a volume messageby 160-character LCD displayq File editing capability for readiness in case of emergencyq Automatic entry of own ship position with manual overrideq PSTN (Public Switched Telephone Network) capability standardq Optional built-in receiver board for DSC ship business/routine frequencies is availableThe FURUNO DSC-60 is a Class A MF/HF DigitalSelective Calling (DSC) system with built-in DSC Watch Receiver designed to fully meet the GMDSS carriage requirements. It complies with new IMO Resolutions A.804 and A.806 as amended by MSC.68(68) and relevant IEC and ETSI testing standards, and ITU Recommendations. The DSC system is one essential element of the GMDSS, enhancing vessel navigation safety with its automated digital communications capabilities.Connected with an associated MF/HF transceiver, the DSC-60 terminal generates and receives digital selective calls for quick and efficient establishment of distress,urgency, safety and routine communications with other ships and coast stations that install MF/HF DSC facilities.The DSC-60 automatically controls the workingfrequencies for radio communications and Telex. Class ofemission and other parameters are also controlled according to the telecommand in an incoming call.In an emergency, the DSC-60 transmits distress alert via the MF/HF radiotelephone by simply pressing the [DISTRESS] button. For monitoring of distress alarm, the DSC-60 incorporates a DSC Watch Receiver which provides continuous scanning of the six distressfrequencies (see spec). On A2 vessels, only 2187.5 kHz is monitored.The DSC-60 can also be used as a remote controller of FURUNO MF/HF radiotelephone or other make which accepts FSI (Frequency Set Information) sentence in IEC 61162-1 digital interface standards.For upgrading of routine communications, a built-in receiver board to scan and receive DSC shipbusiness/routine frequencies (1.6 MHz to 27.5 MHz) is available as an option.The future today with FURUNO's electronics technology.FURUNO ELECTRIC CO., LTD.9-52 Ashihara-cho, Nishinomiya City, Japan Phone: +81 (0)798 65-2111Fax: +81 (0)798 65-4200, 66-4622 URL: www.furuno.co.jpTRADE MARK REGISTEREDMARCA REGISTRADAGENERAL CHARACTERISTICS1.Rules and RegulationsITU-R Rec. 493-9 (Class A), 541-8, 1082-1IEC 61097-3, IEC 61097-8, IEC 61162-1, IEC 60945IMO Res. A.804(19), A.806(19) and MSC.68(68) amendment,EN 300 3382.Distress Call and MessageDistress Call and Message (RR 3112: Format specifier (distress), Self-ID, Nature of distress, Distress coordinates,Time, Telecommand, EOS, ECC)3.Class of Emission DSC:F1B/J2B (J2B MF/HF transceiver)Voice:J3E TTY:F1B/J2B (J2B MF/HF transceiver)4.Receiving FrequenciesMF/HF DSC: 2187.5, 4207.5, 6312, 8414.5, 12577, 16804.5 kHz1.6 to 27.5 MHz (Optional receiver)5.Message Storage Receive: 50 distress messages max. plus 50 non-distressmessagesTransmit: 50 messages plus 99 files containing station ID,Telephone No., Frequency, etc.6.Interface IEC 61162-17.Alarms Audible and visual on receipt of distress, urgency or routine calls, Position error 8.Display20 characters x 8 lines9.Modulator and Demodulator Level:-12 dBm to +12 dBm at 600 ohms, balanced Frequency:Mark 1615 Hz, Space 1785 Hz, 100 baud Stability:±0.5 HzWatch receiverReceive Frequencies:2187.5, 4207.5, 6312,8414.5,12577,16804.5 kHzSensitivity:Error rate 1% at 0 dBµVPOWER SUPPLY24 VDCEQUIPMENT LISTStandard1.DSC terminal/DSC watch receiver2.Installation materials and spare parts3.External loudspeaker MX9010-X01Optional1.Rectifier PR-3002.Printer PP-5103.Distress alert button IC-3024.Incoming indicator IC-3035.Handset HSC701K-B206.1.6-27.5 MHz DSC scan boardSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE01085N Printed in JapanFURUNO U.S.A., INC.Camas, Washington, U.S.A.Phone: +1 360-834-9300 Telefax: +1 360-834-9400FURUNO (UK) LIMITEDDenmead, Hampshire, U.K.Phone: +44 2392-230303 Telefax: +44 2392-230101FURUNO FRANCE S.A.Bordeaux-Mérignac, FrancePhone: +33 5 56 13 48 00 Telefax: +33 5 56 13 48 01FURUNO ESPANA S.A.Madrid, SpainPhone: +34 91-725-90-88 Telefax: +34 91-725-98-97FURUNO DANMARK ASHvidovre, DenmarkPhone: +45 36 77 45 00 Telefax: +45 36 77 45 01FURUNO NORGE A/SÅlesund, NorwayPhone: +47 70 102950 Telefax: +47 70 127021FURUNO SVERIGE AB Västra Frölunda, SwedenPhone: +46 31-7098940 Telefax: +46 31-497093FURUNO SUOMI OYHelsinki, FinlandPhone: +358 9 341 7570 Telefax: +358 9 3417 5716。

DCS维护手册

DCS维护手册主要内容l.维护基础知识l.预防维护l.故障维护一、维护基础知识系统维护的意义l.必要性：系统中任一环节出现问题，均会导致系统部分功能失效或引发控制系统故障，严重时会导致生产停车。

l.系统维护——故障处理、保持系统的良好运行状态、优化系统系统使用维护的主要工作l.预防维护防患于未然，避免出现故障或出现影响生产的故障。

l.故障维护及时有效地发现和排除故障，保障正常生产。

树立正确的维护观念系统维护重在预防！用到哪些常用工具？l.硬件工具：l.仿真器l.过程校验仪、FLUKE、电子电位差计、电阻箱、信号发生器l.线缆测试l.除尘工具l.超声波清洗仪l.接地测试仪表二、预防维护.主要内容1.日常维护2.大修期间维护1、日常维护日常维护的主要内容：l.控制室维护管理l.控制站维护l.操作站维护l.网络维护控制室管理l.密封所有走线孔（坑）；l.保证空调设备稳定运行，室温变化小于+5℃/h，避免凝露；l.现场与控制室合理隔离，防尘，定时清扫，保持清洁；l.通干净仪表空气使控制室保持正压，且室内外压差不应低于25Pal操作台内通入仪表风l尽量保持控制室密封设置两道门使用双层玻璃l使用胶泥封堵控制室电缆进出口l.制定严谨的控制室操作规程，减少人员出入。

l.进出控制室时做到快进快出，随手关门。

窗户密闭l.保持适当的湿度，40%~60%安放湿度检测仪，专人监测湿度过大－放置碱石灰，湿度过小－放置增湿器l.需考虑空调系统自身引入外部腐蚀性气体的问题控制室管理良好的标准l.完备的管理制度l.整洁的环境l.定期的检查和整改l.控制室及周边环境变动应经过严格审批控制站管理l.非维护人员不得擅进机柜室；l.保持柜内外的清洁；l.严禁擅自改装、拆装系统部件；l.不得无故拉动机笼接线、接地供电线及通信电缆；l.锁好柜门，专人保管钥匙；l.定时检查和维护；主控卡及数据转发卡切换l.正常生产过程中主控卡应尽量避免人工切换l.如需工作备用切换，应通过拔出一根工作主控卡的网线来实施l.拔出主控卡并插回后，必须等数据拷贝完成后才可拔另一块主控卡，否则在生产过程中会造成严重后果l.数据转发卡也尽量避免人工切换，如需切换，在拔出数据转发卡并插回后，必须等数据拷贝完成后才可拔另一块数据转发卡操作站硬件维护l.不带电插拔；l.保持清洁，防灰防水；l.严禁擅自改装、拆装机器；l.发现有硬件故障及时向厂家报修；操作站管理l.防止病毒侵入；l.严禁进行不必要的操作；l.做好驱动软件、组态软件的硬盘备份；l.做好组态的备份规范、组态修改记录管理规范；网络维护l.A网、B网不得相互交换；l.定期检查线缆连接的可靠性；l.定期检查各组件指示灯状态；l.定期从各个节点互相PING；l.观察动态数据是否正常显示和刷新；UPS系统维护UPS系统的使用与维护.1、UPS系统组成——UPS、电池.2、运行原理简介.3、电池的使用和维护电池是UPS系统中的重要组成部分，其好坏直接关系到UPS系统正常工作。

DCS系统维护手册

DCSDCS1.1)50~57 8 502)A B 51 523)10# 11# 1 2 12#3 44)2.3.1)2) TCP/IP3) I/O Profibus DPDCS1. FM801POWERSTANDBYRUNRESETBARRERY ON FM801 OFF FM8012.FM148ARDY COM3. FM148ERDY COM4. FM151A 8 4~20mARDY COM5. FM161DRDY COM〔〕备 1~ 16 16 0~ 15 “ ” “ ”6.FM171BRDY COM〔〕备 1~ 16 16 0~ 15 “ ” “ ”7.FM1201 DPRDY COM DP1 DP2〔〕备DP1、DP2 。

DCSFM148A(FM148E FM151A)+FM131A1. FM148A+FM131A2.FM148E+FM131A3. FM151A+FM131A4. FM161D+FM131A〔〕备 DCS DI1524VDC线24VDC原5. FM171B+FM131-E-A+FM138-ACRFM138-ACR 37 FM131-E-A FM138-ACR〔〕备FM138原ACR 3 Ox 、COMx 、Cx x=1原16Ox 、COMx COMx 、Cx COMx 、Cx 备DO系尔引热系符尔引1524VDC线24VDC原个 DCS 1.superman macsv ops, eng, eng2. // /个 DCS1.MACSVYYGSB102.IP3.〔〕备 “ ” “ ”个 DCS1.MACSV aaaa aaaaYYGSB2.IO 10IP A 130.0.0.1 A 131.0.0.1 A IP IP3.IP〔 1〕个 “ ”→“ ”→“”→“ ” 备〔 2〕个备〔 3〕个 “D:\MACSV \SysManage子exe ” 备〔 4〕个 “D:\MACSV\SysManageOPS子exe ” 备备1.MU MD2.0 1 2 3 4 3. PIDPIDDCS1.1 ON2342.12)3)4)a)b) D:\MACSV_ENG\c)YYGSBd)10~8e)f)D:\ MACSV\IE_Win2K_Eternal.exeg) MACSV仓仓、仓然数1、 a作b作 c作。

DSC-60软件更新指南说明书

Updating the DSC-60 SoftwareRefer to: “How to update system program”1) Remove the Top Cover and verify the switches on S3 are correct.2) Refer to the instructions for an IB581 or PC, depending on which unit will be used, toupdate the DSC-60.3) Update both the Main and Modem software.4) After programming cycle power and press the [3/Test] key.5) When the Test is done the alarm will sound.6) Press and hold the [1/RT] key, while pressing the [*/File] key 5 times.7) The software versions should now be: Main CPU 02.12Modem 01.04Refer to: “Resetting Memory-All Clear”1) Follow the “Resetting Memory-All Clear” procedure.Note: Refer to the photos of the Control/Modem PCB and Back panel during these Procedures.3. How to update system program 3. How to update system programThe program disk supplied includes two programs: main program and modem program. To update the system program, DIP switch #1 and #2 of S3 on the CONTROL/MODEM board must be set to ON position. Either of an IB-581 or a PC PC/A T compatible is connected as follows.Using IB-581Any IB-581 using for DP-6, Inmarsat-B and –C can be used.Using PCThe PC is connected to the DSC-60 as below.Connection between DSC-60 and PC/IB-581The connection is made with the following interconnection cable. The connector to the DSC-60 is a 25-pin D-SUB male, and to the IBN-581 or PC a 9-pin D-SUB female.D-SUB 9pin D-SUB 25pin3. How to update system program Refence)Refer er erence)The file size differs depending on the program revision level. The sizes listed here arereference only.File name SizeDSC60BIN689,056LOAD BIN15,304MODEM BIN29,129PROG TXT9UPDSC BA TY38UPMODEM BAT39UPPG EXE74,9603. How to update system program 3.1 Updating MAIN program with IB-5811. Connect the IB-581 to the DSC-60.2. Turn on the IB-581, but do not turn on the DSC-60.3. Terminate the terminal program.When using IB-581 for DP-6, FELCOM 12/81, while press and holding down [Alt] and[Fn], press [F2]. For example, A:\DP10\TERMINAL appears on the DP-6 terminal.When using IB-581 for FELCOM 11, press [F1] and [8] in order.4. Insert the program floppy disk in the slot.5. Type B: and press [Enter]. The prompt B:\> appears.6. Type “UPDSC” and press [Enter]. The following message appears.Program upload utility Version 6.21Copyright(c) FURUNO ELECTRIC CO., LTD.1997,1998,1999 (T.K)uppg infile 1 infile 2 p1 p2 p4 p5p1:Deletion waiting time.p2:Waiting time to write.p3:Password output interval.p4:ID number.(1,2...)p5:Poer number.(1,2...)Erase Wait:osecWait:oWait counter=100Port no.=1TARGET POWER ON.7. Turn on the DSC-60.The indication on the DSC screen changes as below. The picture on the IB-581 runs.8. Wait for about 5 minutes.9. The DOS prompt appears after the message “Finish version up.”10. Turn off the DSC-60, disconnect the IB-581 and turn on the DSC-60 again.11. Press [3/TEST/DEF] to perform the selftest and confirm the program has been updated.3. How to update system program 3.2 Updating MODEM program with IB-5811. Connect the IB-581 to the DSC-60.2. Turn on the IB-581, but do not turn on the DSC-60.3. Terminate the terminal program.When using IB-581 for DP-6, FELCOM 12/81, while press and holding down [Alt] and[Fn], press [F2]. For example, A:\DP10\TERMINAL appears on the DP-6 terminal.When using IB-581 for FELCOM 11, press [F1] and [8] in order.4. Insert the program floppy disk in the slot.5. Type B: and press [Enter]. The prompt B:\> appears.6. Type “UPMODEM” and press [Enter]. The following message appears.Program upload utility Version 6.21Copyright(c) FURUNO ELECTRIC CO., LTD.1997,1998,1999 (T.K)uppg infile 1 infile 2 p1 p2 p4 p5p1:Deletion waiting time.p2:Waiting time to write.p3:Password output interval.p4:ID number.(1,2...)p5:Poer number.(1,2...)Erase Wait:osecWait:oWait counter=100Port no.=1TARGET POWER ON.7. Turn on the DSC-60.The message “Now Loading” appears on the DSC screen. The picture on the IB-581 runs.8. Wait for about 5 minutes.9. The DOS prompt appears after the message “Finish version up.”10. Turn off the DSC-60, disconnect the IB-581 and turn on the DSC-60 again.11. Press [3/TEST/DEF] to perform the selftest and confirm the program has been updated.3. How to update system program3.3 Updating MAIN program with PC1. Connect the PC to the DSC-60.2. Turn on the PC, but do not turn on the DSC-60.3. Insert the program floppy disk in the slot.4. Type a: and press [Enter] to select drive A5. Type “UPDSC” and press [Enter]. The following message appears.Program upload utility Version 6.21Copyright(c) FURUNO ELECTRIC CO., LTD.1997,1998,1999 (T.K)uppg infile 1 infile 2 p1 p2 p4 p5p1:Deletion waiting time.p2:Waiting time to write.p3:Password output interval.p4:ID number.(1,2...)p5:Poer number.(1,2...)Erase Wait:osecWait:oWait counter=100Port no.=1TARGET POWER ON.6. Turn on the DSC-60.The indication on the DSC screen changes as below.Execute STEP1Execute STEP2xxxxxByte transferNow Erasingxxx percent completed7. Wait for about 5 minutes until the xxx percent reaches to 100.8. The DOS prompt appears after the message “Finish version up.”9. Turn off the DSC-60, disconnect the IB-581 and turn on the DSC-60 again.10. Press [3/TEST/DEF] to perform the selftest and confirm the program has been updated.3. How to update system program3.4 Updating MODEM program with PC1. Connect the PC to the DSC-60.2. Turn on the PC, but do not turn on the DSC-60.3. Insert the program floppy disk in the slot.4. Type a: and press [Enter] to select drive A.5. Type “UPMODEM” and press [Enter]. The following message appears.Program upload utility Version 6.21Copyright(c) FURUNO ELECTRIC CO., LTD.1997,1998,1999 (T.K)uppg infile 1 infile 2 p1 p2 p4 p5p1:Deletion waiting time.p2:Waiting time to write.p3:Password output interval.p4:ID number.(1,2...)p5:Poer number.(1,2...)Erase Wait:osecWait:oWait counter=100Port no.=1TARGET POWER ON.6. Turn on the DSC-60.The indication on the DSC screen changes as below.Execute STEP1Execute STEP2xxxxxByte transferNow Erasingxxx percent completed7. Wait for about 5 minutes until the xxx percent reaches to 100.8. The DOS prompt appears after the message “Finish version up.”9. Turn off the DSC-60, disconnect the IB-581 and turn on the DSC-60 again.10. Press [3/TEST/DEF] to perform the selftest and confirm the program has been updated.DSC-60Resetting Memory-All Clear1. Remove the top cover by removing the 4 side screws, and 1 screw from the rearpanel of the DSC-60.2. Connect power to the DSC-60.3. Turn on the unit and wait for the WATCH KEEPING screen to appear.4. Press the SETUP key. Use the arrow keys to select SYSTEM.Press the ENT key.5. Record the system settings, these will need to be reentered later.6. Press the CANCEL key to return to the WATCH KEEPING screen.7. Press the NMI switch located on the front right of the Control/Modem PCB(05P0702). Refer to the attached Control/Modem page.8. The unit will now display:9. Enter the password, 652111. As you enter the password, the unit will emit error tones.Ignore the error tones as you enter the password.10. Use the down arrow key to select ALL Clear. Press the ENT key.11. Enter the 9 digit MMSI number. Press the ENT key.DSC-60Resetting Memory-All Clear (Cont.)12. The display will now show PLEASE POWER OFF.Turn off the DSC-60 power.13. Turn the DSC-60 power back on.14. Now verify the System Settings and MMSI.15. Press the SETUP key. Use the arrow keys to select SYSTEM.Press the ENT key.16. Enter the password, 652111. As you enter the password, the unit will emit error tones.Ignore the error tones as you enter the password17. Renter the system settings recorded earlier.18. Turn the power off, put the top cover back on and reinstall the unit.2.3 CONTROL/MODEM(05P0702)(RS-232C/422)S2:DMC S3:NBDP S4:RTU21:PIO/SIOU4:F .ROM(MAIN)U6,7:SRAMU3:MAIN CPUU15:GATE ARRAY S 1: N M I S WU5:EEPROM U13:DSPC67U11:F .ROM(MODEM)U12:CODECC34(C.Loop/RS-422)S5(DMC) S8 S7 S6J1J2J3J4J5J6J7J8J9R152S4 [RT] S3 [NBDP]S2 [DMC]S6S7S8232422[CALL]DMCS4-S2: Selection of TX/RX data communication system of S4:RT“232” in case of MIF format“422” in case of IEC-6112 formatS3,S2:NBDP and DMC“232” in case of RS-232C “422” in case of RS-422S5: Selecting hardware of RX data (C.Loop/RS-422) S5-1 NBDP S5-2 RT S5-3 DMC S5-4 NMEAS6-S8: Selection of TX/RX data communication system of DMC2. PCBsS5[C.Loop]2.WIRING 2.1Wiring2.1.1Standard wiringAll external equipment are connected to appropriate connectors on the rear panel of the DSC-60. The figure below shows the location of these connectors. Note that all interconnection cables are optionally supplied. For further details, refer to the interconnection diagram at the end of this manual.DMC (current loop) or Distress Alert UnitReceiver AntennaPower 24 VDC TPower (24 VDC)Attach the connector (supplied) to the power cable and plug it into the 24 VDC connector at the rear of the main unit. When connecting to the optional AC-DC power supply unit PR-300, supply AC power and DC power to the PR-300. See paragraph “2.2 Connection of AC-DC Power Supply Unit PR-300” for detail.Ground ()Connect either a copper strap or 1.25 sq vinyl wire (local supply) between ship’s superstructure and ground terminal on the DSC-60.Note: Ground the equipment to prevent mutual interference.。

通讯设备维修操作手册

通讯设备维修操作手册第一章：概述 (2)1.1 维修目的与意义 (2)1.2 维修范围与对象 (3)第二章：维修准备工作 (3)2.1 维修工具准备 (3)2.2 维修材料准备 (4)2.3 维修环境要求 (4)第三章：通讯设备基本结构 (5)3.1 设备主要部件 (5)3.2 设备功能模块 (5)3.3 设备接口与连接 (5)第四章：故障诊断与判断 (6)4.1 故障类型识别 (6)4.2 故障诊断方法 (6)4.3 故障判断标准 (6)第五章：维修操作流程 (7)5.1 维修前检查 (7)5.2 维修操作步骤 (7)5.3 维修后检查 (8)第六章：常见故障维修方法 (8)6.1 硬件故障维修 (8)6.1.1 内存故障 (8)6.1.2 硬盘故障 (8)6.1.3 显卡故障 (8)6.2 软件故障维修 (8)6.2.1 系统故障 (9)6.2.2 软件冲突 (9)6.2.3 病毒感染 (9)6.3 网络故障维修 (9)6.3.1 网络连接故障 (9)6.3.2 网络速度慢 (9)6.3.3 网络安全问题 (10)第七章：维修注意事项 (10)7.1 维修安全操作 (10)7.2 维修禁忌事项 (10)7.3 维修记录与报告 (11)第八章：设备保养与维护 (11)8.1 定期保养 (11)8.1.1 检查设备运行状态 (11)8.1.2 检查设备紧固件 (11)8.1.3 检查设备润滑系统 (11)8.1.4 检查设备电气系统 (11)8.2 设备清洁 (12)8.2.1 清洁设备表面 (12)8.2.2 清洁设备内部 (12)8.2.3 清洁设备过滤系统 (12)8.3 设备故障预防 (12)8.3.1 建立设备档案 (12)8.3.2 开展设备点检 (12)8.3.3 强化操作人员培训 (12)8.3.4 完善设备管理制度 (12)8.3.5 加强设备监测与诊断 (12)第九章：维修工具与材料管理 (12)9.1 维修工具管理 (12)9.2 维修材料管理 (13)9.3 库存管理与采购 (14)第十章：维修人员培训与考核 (14)10.1 培训内容与方法 (14)10.1.1 培训内容 (14)10.1.2 培训方法 (15)10.2 培训计划与安排 (15)10.2.1 培训计划 (15)10.2.2 培训安排 (15)10.3 考核标准与评价 (15)10.3.1 考核标准 (15)10.3.2 评价方法 (16)第十一章：维修服务与客户沟通 (16)11.1 客户需求分析 (16)11.2 服务流程与规范 (16)11.3 客户满意度提升 (17)第十二章：维修案例分析与总结 (17)12.1 经典维修案例 (17)12.2 维修经验分享 (18)12.3 维修问题与改进 (18)第一章：概述1.1 维修目的与意义维修，作为一种保障设备正常运行的重要手段，其目的在于保证设备的安全、可靠和高效。

岛津差示扫描量热仪DSC-60操作规程

岛津差示扫描量热仪DSC-60操作规程岛津差示扫描量热仪DSC-60操作规程目录样品分析.........................................................................................1.1 开机..............................................................................................1.2 气体..............................................................................................1.3 样品制备......................................................................................1.4 设定测定参数..............................................................................1.5 样品测试......................................................................................1.6 关机..............................................................................................1.7基线校准........................................................................................样品分析1.1 开机打开DSC-60主机、计算机、TA-60WS工作站以及FC-60A气体控制器。

DCS系统操作手册

DCS系统操作手册1、系统界面。

打开系统时，系统界面如下：上部为菜单栏，分别为“系统菜单”，“前一副”，“后一副”，“图形管理菜单”，“工程师功能菜单”，“综合功能菜单”，“历史趋势菜单”，“显示表格菜单”，“显示日志菜单”，“系统名称显示”，“报警光字牌”“系统基本属性显示框”。

菜单栏以下为报警栏，可显示10条报警，以点说明方式显示，超过10条报警时，滚动显示。

下部为状态栏，显示系统登录级别、权限位置，还有服务器属性。

中间为工作区，主要的操作、显示等工作的区域。

2、操作员系统登录打开系统进入DCS操作界面时，默认系统运行的操作权限为监视级，即只能进行观察，不可以进行任何操作，操作人员只有登录到操作员级别以上，方可进行各种操作。

登录操作员时要注意，要根据权限位置，登录操作员的用户名不同。

权限位置在系统下侧偏右端，如显示“操作员级权限1”则表示此操作员站现在权限位置为“1”，登录的级别为操作员级。

目前只设置“权限1”和“权限0”两种权限位置。

选择“工程师工程功能菜单”—＞“登录”，登录界面如下：登录操作员时：，权限1对应的操作员登录的用户名为ops，没有密码。

权限0对应的操作员登录的用户名为ops0，没有密码。

登录到操作员后，可对系统进行基本操作，添加趋势，查看报警等。

3、趋势查询操作画面上有各种数据显示点，右键单击该点，选择点趋势，可查看该点的趋势画面。

注意：趋势画面是记录可以查看前推最近一次下装服务器到当前时间的点趋势。

点趋势画面如下：上侧，分别显示该点的点名，时间间隔。

时间间隔可以输入从1~60的整数，单位是秒，时间间隔是趋势曲线变化的时间率，即输入5秒，曲线5秒钟变化一次。

趋势曲线的状态可分为“跟踪”和“历史”两种状态，选择跟踪，曲线便根据时间间隔和实际数据变化而实时更新，选择历史则曲线不再变化，而点趋势画面下侧的“前推”和“后推”按钮可用，每推一次即翻一页。

趋势显示的方式分为“曲线”和“数字”两种，选择数字，则点的趋势以数据方式显示。

福隆DSC-60手机号监控收音机用户操作指南说明书

Installation Manual DSC/WATCH RECEIVERDSC-60SAFETY INSTRUCTIONS .............................................................................i SYSTEM CONFIGURATION.........................................................................ii EQUIPMENT LISTS.....................................................................................iii 1. MOUNTING.. (1)1.1 Main Unit............................................................................................................................11.2 Antenna (option).................................................................................................................31.3 External Loudspeaker ........................................................................................................51.4 Handset Hanger (option)....................................................................................................51.5 AC-DC Power Supply Unit (option).....................................................................................51.6 Printer PP-510 (option).......................................................................................................61.7 Distress Alert Unit IC-302-DSC/Incoming Indicator IC-303-DSC. (6)2. WIRING (7)2.1 Wiring.................................................................................................................................72.2 Connection of AC-DC Power Supply Unit PR-300 (option) (11)3. INITIAL SETTINGS (13)3.1 System Setup...................................................................................................................133.2 Setting of DIP Switches....................................................................................................173.3 Preamp Setting (20)4. RX BOARD (OPTION)............................................................................21PACKING LISTS.......................................................................................A-1OUTLINE DRAWINGS..............................................................................D-1SCHEMATIC DIAGRAMS.........................................................................S-1The paper used in this manualis elemental chlorine free.9-52 Ashihara-cho,SYSTEM CONFIGURATION24 VDC100-115/200-220 VAC1φ, 50/60 HzNote: DISTRIBUTOR DB-120/DB-500 not necessarywhen using FS-5000 series radiotelephone.EQUIPMENT LISTSStandard SupplyName Type Code no.Qty RemarksMain Unit DSC-60-1Installation Materials CP05-07901005-950-180 1 setAccessories FP05-05200000-055-407 1 set FP05-05201, FP05-05202,LoudspeakerOptional EquipmentNameTypeCode no.QtyRemarksOP05-91005-950-34005P0703 boardRX Board Kit OP05-93005-950-610 1 set 05P0703 board, w/shield casesAC-DC Power Supply Unit PR-300000-130-4311PrinterPP-510- 1 setw/installation materials (CP16-01200), accessories (FP16-00100)Distress Message Controller DMC-5-Distress Alert Unit IC-302-DSC - 1 set w/Installation materials Incoming Indicator IC-303-DSC - 1 set w/Installation materials Whip Antenna 04S4176000-112-8451 2.6 meterPreamp Unit FAX-5000-075-016 1 set 05S0784*1m*000-123-58205S0784*3m*000-123-583Cable Assy05S0784*5m*000-123-5841For SSB radiotelephone, w/D-sub connectorsOP04-2*10m*000-041-174OP04-2*20m*000-041-175OP04-2*30m*000-041-176OP04-2*40m*000-041-177Extension Cable Kit OP04-2*50m*000-041-1781For extension of FAX-5 cableCO-SPEVV-SB-C 0.2X2P*5m*000-111-680CO-SPEVV-SB-C 0.2X2P*10m*000-120-792CO-SPEVV-SB-C 0.2X2P*15m*000-120-793CO-SPEVV-SB-C 0.2X2P*20m*000-120-794CO-SPEVV-SB-C 0.2X2P*30m*000-120-2141For navigator, DMC-5CO-SPEVV-SB-C 0.2X5P*5m*000-560-451CO-SPEVV-SB-C 0.2X5P *10m*000-560-452CO-SPEVV-SB-C 0.2X5P *15m*000-139-427CO-SPEVV-SB-C 0.2X5P *20m*000-103-868Twisted-pair CableCO-SPEVV-SB-C 0.2X5P *30m*000-103-8691For distress alert unit/received call unitHandset/bracket HSC701K-B20000-138-0001 set1. MOUNTINGUnit1.1 Main1.1.1 GeneralThe DSC-60 can be mounted on the overhead, on a tabletop, on a bulkhead, or flush mounted in a panel. Mount the unit where it can be easily viewed and operated. When selecting a mounting location, keep in mind the following considerations, in addition to those already mentioned.•Locate the unit away from water splash and rain.•The temperature and humidity of the location should be stable and moderate.•Keep the unit away from exhaust gas and heating and cooling vents.•Select a well ventilated location.•Select a location where shock and vibration are minimal.1.1.2 Compass safe distanceA magnetic compass will be affected if placed too close to the main unit. Keep the following compass safe distances in mind when selecting a mounting location.Standard compass:0.3 metersSteering compass:0.2 metersOverhead TabletopFlush Mount Bulkhead1.1.3 Mounting2581083065- 7.5190305100100150 3264545123Notes•All dimensions in millimeters.•For added support fasten unit to mounting location with nuts, bolts and washers instead of tapping screws.•Leave sufficient space at sides and rear of the unit for maintenance and service purposes.The minimum recommended space appears in the figure above.1.1.4Flush MountingThe hanger is mounted with the unit when the unit is flush mounted. Be sure the mounting location is strong enough to support the weight of the unit.Prepare cutout of 255 x 103 in panel.983897.5187.5(option)1.2 AntennaPerformance of this unit is directly related to the antenna installation. In general, the antenna should be installed as high as possible on the boat, free from the influence of nearby antennas, rigging and masts.The antenna commonly used for the DSC-60 is a 6 m whip antenna (local supply), long wire or optional whip of 2.6 m length with preamp unit (optional supply).The antenna input on this unit is automatically protected against strong induction by a protective circuit. For better performance, however, we recommended use of the preamp unit FAX-5.Antenna cable (option)Connect the antenna to the unit with any 50 ohm coaxial cable (RG-10U/Y or equivalent). Connect the center conductor of the coaxial cable using the junction box (type: AJB1-1A, code no.: 000-870-284, order from FURUNO).AJB1-1APreamp unit (option)The body of the preamp unit can be mounted two ways;1. The bottom of the preamp unit is designed to accept a threaded extension mast of 1 inchdiameter. The pitch of the thread should be 14 threads per inch. T o prevent undue flexing of the mast in heavy winds, the mast should not be longer than 5 feet (1.5 m).2. The side of the preamp unit has a molded channel so that it may be mounted directly to astub mast with two stainless steel hose clamps. Hose clamps must be arranged locally. Screw the 2.6 m whip antenna tightly onto the preamp unit and waterproof the junction and other exposed metallic parts with sealing compound (silicone rubber, putty, etc.).Note that a wire antenna of 2 to 3 meters length may be used instead of the whip antenna. Note: The preamp unit requires about 9 VDC power. See page 20.Thread(14 threads/inch)1" Pipe2.6 m Whip AntennaMastHose ClampCoupling NutAntenna Wire Wire Antenna FixturePreamp Unit50Earth1.3External LoudspeakerThe external loudspeaker sounds the alarm. It can be installed on a tabletop, the overhead or bulkhead. Fasten the loudspeaker to the mounting location with tapping screws, or nuts, bolts and washers. For mounting dimensions, see the outline drawing at the end of this manual.1.4Handset Hanger (option)The mounting location should provide easy access to front panel controls while operating the handset. Also, the length of the standard handset cable is 100 cm, so locate the handset hanger within 100 cm of the unit.1.5AC-DC Power Supply Unit (option)For Convention vessels, both AC and DC power must be fed to the DSC-60, via an AC-DC power supply unit. When AC input fails, DC power is supplied. FURUNO can supply the PR-300 AC-DC power supply unit.1.5.1Mounting considerationsWhen selecting a mounting location, keep in mind the following points.•Select a location which provides adequate ventilation.•The location must be clean and dry.•The mounting location must be able to support the weight of the unit (14.5 kg) under the continued conditions of vibration normally encountered aboard the vessel. If necessary,reinforce the mounting location.•The PR-300 will affect a magnetic compass if it is placed too near the compass. Observe the following compass safe distance to prevent deviation of a magnetic compass;Standard compass:0.9 metersSteering compass:0.7 meters1.5.2MountingRefer to outline drawing at the end of this manual.1.6Printer PP-510 (option)Install the unit with the two mounting fixtures (supplied). Refer to the outline drawing at the end of this manual. Connect the interconnection cable between the printer and the DSC-60.For how to load paper and set ribbon cassette, refer to the Operator’s Manual of the printer. Mounting1. Select a flat surface. (Compass safe distance, Standard, 1.0 meters, Steering, 0.8 meters)2. Fix the printer to the mounting location with two mounting fixture.1.7 Distress Alert Unit IC-302-DSC,Incoming Indicator IC-303-DSCSelect the mounting location where the button on the unit can be operated easily in an emergency. See the back of the manual for mounting dimensions and recommended clearance space. (Compass safety distance: Standard, 0.8 m, Steering, 0.6 m)Unfasten four screws to remove the cover.1.2. Fasten IC-302 with four tapping screws to remove the cover.3. Pass the cable through appropriate entrance to connect to the terminal board.There are two cable entrances, one at the bottom and on the back. Select one.4. Attach the cover with four screws.2.WIRING 2.1Wiring2.1.1Standard wiringAll external equipment are connected to appropriate connectors on the rear panel of the DSC-60. The figure below shows the location of these connectors. Note that all interconnection cables are optionally supplied. For further details, refer to the interconnection diagram at the end of this manual.DMC (current loop) or Distress Alert UnitReceiver AntennaPower 24 VDC TPower (24 VDC)Attach the connector (supplied) to the power cable and plug it into the 24 VDC connector at the rear of the main unit. When connecting to the optional AC-DC power supply unit PR-300, supply AC power and DC power to the PR-300. See paragraph “2.2 Connection of AC-DC Power Supply Unit PR-300” for detail.Ground ()Connect either a copper strap or 1.25 sq vinyl wire (local supply) between ship’s superstructure and ground terminal on the DSC-60.Note: Ground the equipment to prevent mutual interference.D.ANT (Distress & Safety Watch Keeping Receiver Antenna)The DSC antenna is connected to the main unit with a 50 ohm coaxial cable, type RG-8/8U or equivalent. Attach an M-type plug (if necessary) to the cable as shown below. Screw the plug into the D. ANT connector at the rear of the main unit.ANT (optional Rx Board kit is required)The antenna is connected to the main unit with a 50 ohm coaxial cable, type RG-8/U or equivalent. Be sure to leave some slack in the cable for future service and maintenance.Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as follows.1. Remove the sheath by 30 mm.2. Bare 23 mm of the center conductor. Trim braided shield by 5 mm and tin.3. Slide coupling ring onto cable.4. Screw the plug assembly on the cable.5. Solder plug assembly to braided shield through solder holes. Solder contact sleeve toconductor.6. Screw coupling ring into plug assembly.7.Screw the plug into the ANT connector at the rear of the main unit.Solder here.sides of hole.SPConnects the loudspeaker MX910-X01 (supplied with the accessories) here.2.1.2External EquipmentIEC61162-1 (NMEA)Connects a navigator here. The DSC-60 can receive the following sentences in IEC-61162-1format. Use the FM14-5P connector (supplied) and interconnection cable type CO-SPEVV-SB-C 0.2x2P (option). For how to fabricate the cable, see the figure in below.• GLL: Latitude and longitude• RMC: Generic navigation information • RMA: Loran C data (L/L, LOPs, etc.)• GGA: GPA position, UTC •ZDA: UTC, day, month, and yearPriority: GGA>RMC>RMA>GLL>ZDAPriority is kept for one minute.DMCConnects the DMC Terminal DMC-5 or Distress Alert Unit IC-302 here using the appropriate cable and connector. For the fabrication, see the figure in below.• DMC-5: CO-SPEVV-SB-0.2X2P cable (option) and FM14-6P connector (supplied).•IC-302: CO-SPEVV-SB-0.2X5P cable (option) and FM14-6P connector (supplied)RCV. BZConnects the indicator IC-303 here. Use the FM14-7P connector (supplied) and CO-SPEVV-SB-C 0.2X5P cable (option). For how to fabricate the cable, see the figure in below.Twist and trim the shield.Vinyl tapeRemove the outer sheath and armor by 45 mm.Remove the inner sheath by 14 mm,and the sheath of the cores by 3 mm.Cut the unused cores.Solder a vinyl wire to the sheild.Vinyl wireSolder the cores to the connector,and tape the sheath.Fabrication of CO-SPEVV-SB-C for IEC61162-1, DMC and RCV. BZ terminalsPRINTERConnects the printer PP-510 (option).HANDSETConnects the HSC701K-B20 handset (option).RTConnects the SSB radiotelephone, by using the cable assembly 05S0784 (option).For the cable assembly UL2464-SB(M) (local supply, with no connector), fabricate the connector 17JE-23250-02 (DSC, supplied as installation materials) as below.Fold back the shield, and thenwind the metallic shield tapeCable ClampCableType: UL2464-SB(M)Code no.: 000-125-302Note: For this cable fabrication;FS-1562/2550: Connector supplied as installation material is not used.FS-5000 series: Cut one side of the cable, and connect to the terminal board in the equipment.2.2Connection of AC-DC Power Supply UnitPR-300 (option)When connecting to an AC and DC ship’s mains, the optional AC-DC power supply unit PR-300 is required. Attach the crimp-on lug FV5.5-S4 (local supply) to the power cable (local supply) for connection with the PR-300. Use the power cable as below.•For AC power:DPYC-1.25 (Japan Industrial Standard) or equivalent•For DC power:DPYC-2.0 (Japan Industrial Standard) or equivalentSheathPaintS =1.25 mm=1.35 mm2(DPYC-1.25)S = 2.0 mm=1.8 mm2(DPYC-2) DPYC, sectional view2.2.1Changing tap connectionsThe transformer tap for input voltage has been st to 220 VAC (fuse 5A) at the factory.If necessary, change the transformer taps setting according to ship’s mains.100VAC SHIP'S MAINS110VAC SHIP'S MAINS200VAC SHIP'S MAINS220VAC SHIP'S MAINSTap connections in the PR-3002.2.2 Changing the power fuseChange the power fuse according to AC input voltage as follows.AC ship’s mains Fuse100/110 VAC10 A200/220 VAC 5 AFuse for AC ship's mainsAC-DC power supply unit PR-300, rear view2.2.3 GroundingConnect a ground wire between ship’s superstructure and a fixing screw on the PR-300.3.INITIAL SETTINGWhen turning on the power for the first time, the following items should be set on the System setup or Alarm setup menus.•Own ship’s ID•Watch receiver frequency band•Line out level for DSC signal•Transmission key timing•Remote control protocol for RT (Radiotelephone) port•Remote station function•Remote control for NBDP port•Detecting DSC signal strengthSetup3.1 SystemThe system setting is necessary after the installation. To prevent accidental transmission of the distress alert, remove the connector of SSB radiotelephone except when the sailing. This setting should be entered by a qualified technician. Under no circumstances shall the operator enter ship’s ID.3.1.1Opening the System Setup menu1. Press [SETUP] key to display the Setup menu.Setup menu2. Select “SYSTEM” with the cursor pad.3. Press the [ENT] key to display the System setup menu.4.Enter a password referring to the FURUNO INFORMATION.<Page 1> <Page 2>System setup menu3.1.2Watch receiver frequency bandSet the watch receiver as below.1. Open the System setup menu.2. Press or to select “WATCH RCVR”.3. Press the [ENT] key to display the WATCH RCVR pop-up window as below.WATCH RCVR pop-up window4. Pressor to select “MF/HF” or “MF” as appropriate.MF/HF: Maximum six distress/safety frequencies are available. (A1, A2, A3 and A4 area)MF: Distress/safety frequency is 2187.5 kHz only (A1 and A2 area)5. Press the [ENT] key.3.1.3Line out level for DSC signal settingSet line out level. For FURUNO SSB (600 Ω), set 0 dBm.1.Open the System Setup menu.2.Press or to select “LINE OUT”.3. Press the [ENT] key to display the pop-up window for adjustment of line out level.LINE OUT LEVEL pop-up window4. Press or to adjust the indicator bar (1.5 dBm step).5. Press the [ENT] key.3.1.4Transmission key timing settingSelect transmission timing, that is, the delay time in seconds to allow for tuning of transmitter before message is transmitted. (When connecting to other makes of SSB, set according to specifications of equipment.)1. Open the System setup menu.2. Press ! or " to select “TX-KEY TIMING”.3. Press the [ENT] key to display the pop-up menu for adjustment of transmission timing.TX-KEY TIMING pop-up window4. Press # or $ to adjust the indicator bar (AUTO, 0.1, 0.5, 1, 2, 3, 4, 5, 10, 15).FURUNO’s SSB: Set to AUTO (Timing is controlled by the MIF command <TU>.)Other makes of SSB: Set according to specifications of equipment.5. Press the [ENT] key.3.1.5Remote control protocol for RT (Radiotelephone) Port Select the protocol depending on the SSB radiotelephone connected.1. Open the System setup menu.2. Press ! or " to select “RT PORT”.3. Press the [ENT] key to display the RT PORT pop-up window.4. Press ! or " to select the appropriate setting.MIF:When connecting a FURUNO SSB radiotelephone (ex. FS-1562, FS-5000/8000).IEC:When connecting another maker’s SSB radiotelephone having IEC-61162-1 format.OFF: When connecting the radiotelephone having protocols except MIF/IEC, or not having remote control function.5. Press the [ENT] key.Note: When connecting with FS-1562/2550, set the system setting for remote operation on radiotelephone.3.1.6Remote station functionThis equipment can function as a SSB radiotelephone remote station as following procedure.1. Open the System setup menu.2. Press or to select “REMOTE STATION”.3. Press the [ENT] key to display the REMOTE STATION pop-up window.REMOTE STATION pop-up menu4. Press or to select the appropriate setting.ON: Function as remote station. ([RT/2182] key is available.)OFF: Not function as remote station.5. Press the [ENT] key.3.1.7Remote control for NBDP PortSelect ON or OFF depending on whether NBDP terminal is connected or not.1. Open the System setup menu.2. Press or to select “NBDP PORT”.3. Press the [ENT] key to display the NBDP PORT pop-up window.NBDP PORT pop-up window4.Press or to select the appropriate setting.OFF: Connecting with other maker’s NBDP or no NBDP.ON: FURUNO’s NBDP (ex. DP-6).4. Press the [ENT] key.3.1.8DSC signal strengthCH DET S LEVEL judges whether the DSC frequency to use to send a DSC message (Routine and Business only) is in use or not. The DSC message is not transmitted when the signal strength on the DSC frequency is higher than that set here. When the DSC frequency becomes clear, the DSC message is automatically transmitted. The setting range is OFF - 250 and the default setting is 100.1. Open the System setup menu.2. Press or to select “CH DET S LEVEL”.3. Press the [ENT] key to display the CH DET S LEVEL pop-up window.CH DET S LEVEL pop-up window4. Press or to adjust the indicator bar. T oo low a setting stops transmission of a DSCmessage because it detects noise on the DSC frequency. Alternately, too high a setting transmits the DSC message though low signal level is present on the DSC frequency used.5. Press the [ENT] key.3.2Setting of DIP SwitchesWhen the following equipment are connected, set the DIP switches in the main unit to select Current Loop, RS-232C or RS-422.•SSB radiotelephone•NBDP terminal•DMC terminal•NavigatorS6S7S8S6S7S8S2S3S4(RT)(NBDP)(DMC)232CALL (Except IC-302)3.2.1 Setting for SSB radiotelephone and NBDP terminalconnectionConnection with FS-1562 and DP-6, exampleConnection with FS-5000 and DP-6, exampleTx/Rx control data of FURUNO’s SSB radiotelephone is MIF protocol, RS-232C format.For SSB radiotelephone (RT)DIP switch S4#1#2#3#4ON ON OFF OFF(Setting for RS-232C setting)For NBDP terminalDIP switch S3#1#2#3#4ON ON OFF OFF(Setting for RS-232C)Note 1:When not connecting to NBDP terminal, set 1 and 2 to ON, 3 and 4 to OFF of S3, select OFF at the NBDP on the system setting menu.Note 2:When the distance between the DSC-60 and radiotelephone is 5 m or more use the current loop specification. To do this, set 1/2 and 3/4 of DIP switch S4 to OFF and ON, 2 of DIP switch S5 to C. Loop respectively. Also, set up the radiotelephone for current loop specification.3.2.2For other transceiver connectionWhen connecting to the transceiver which cannot be controlled by IEC-61162 format, select OFF at RT PORT on the setup menu.When connecting to other maker’s transceiver which is controlled by IEC-61162 format, set the DIP switches in the main unit.For SSB radiotelephone (RT), TX dataDIP switch S4#1#2#3#4OFF OFF ON ON(Setting for RS-422)For SSB radiotelephone (RT), RX dataDIP switch S5#2 is ON Setting for RS-422#2 is OFF Setting for Current Loop3.2.3For navigator connectionDSC-60[IEC]Navigator NAV DA T A(GLL,RMC,RMA,GGA,ZDA)Navigator connectionSet the output data format from the navigator to IEC: RS-422 or Current Loop, and set S5 DIP switch in the main unit as below.For IEC: RS-422DIP switch S5#4ONFor Current LoopDIP switch S5#4OFF3.2.4Connection to DMC-5, IC-302-DSCThe above equipment can be connected at DMC port at the back of the main unit. When connecting to them, set DIP switches as below.DMCSet to RS-422 as follows.S2S5S6S7S8#1#2#3#4#3#1#2#3#4#1#2#3#4#1#2#3#4OFF OFF ON ON OFF ON ON ON ON OFF OFF OFF OFF OFF OFF OFFOFFIC-302-DSCSet to Current Loop for IC-302 connection.S6S7S8All All AllOFF OFF ON3.3 PreampSettingWhen using the preamp for the watch receiver antenna, set J3 on the RX Board to ACTIVE.4. RX BOARD (OPTION)The RX Board 05P0703 (option) enables reception of routine DSC frequencies without the SSB radiotelephone connection. For complete modification, the whip antenna for routine DSC frequency is necessary.• Necessary Parts :RX Board Kit, Type :OP05-91, Code No. :005-950-340:RX Board Kit, Type :OP05-93, Code No. :005-950-610 (with shield case)No.RemarksQtyCodeName TypeRX Board 05P0703 005-950-530 1Connector assembly PH16DK-180 000-142-865 1Pan head screws M3X8 000-881-404 6Shield case RX-1 05-085-1051 100-285-160 1 OP05-93 onlyShield case RX-2 05-085-1052 100-285-170 1 OP05-93 onlyPan head screws M3X8 000-881-404 13 OP05-93 onlyThe unit functions normally without the shield case, however its use is recommended when noise might be a problem.Mounting1. Unfasten ten binding screws to remove the upper and lower covers from the main unit.2. For mounting the OP05-93, remove RX Board for distress frequencies.3. For mounting OP05-93, set the shield case RX-1 inside the main unit as shown below.Set fixing holes in shield case RX-1 to “pegs” in main unit.4. Fasten the optional RX Board 05P0703 inside the main unit with six pan head screws (M3X8,supplied). For mounting OP05-93, fasten the RX Board with shield case RX-1 with sixscrews.5. Attach the coaxial cable (from the rear panel) to J1 on the RX Board. For mounting OP05-93,attach the coaxial cable to J1 through the square bush of shield case RX-2.6. Connect the PH16PDK-180 connector assembly (supplied) between J2 on the RX Boardand J7 on the CONTROL/MODEM Board.Pass the PH16DK-180 connectorassembly through this hole.Coaxial cable16P connector assy;From J2 on theRX Board (option)Note:When using the preamp unit (option), change jumper plug position on J3 to “ACTIVE” on the RX Board to supply power to the preamp unit. For detail, see “3.3 Preamp Setting”on page 20.7. For mounting OP05-93, fasten the shield case RX-2 inside the main unit with thirteen panhead screws.Be careful not to pinch 16P connector assembly by the shield cover RX-2.8. For mounting OP05-93, refasten the RX Board for distress frequencies with six pan headscrews.9. Reassemble the main unit.。

DSC操作规程

DSC操作规程DSC操作规程（包括DSC使用原则、装备准备、操作步骤等），以下是一份完整版的规程，超过1200字。

一、DSC使用原则1.DSC使用是为了确保通信的有效性和安全性，应按照国家相关法规和通信礼仪进行操作，绝不得滥用DSC进行虚假报警或传播虚假信息。

2.DSC操作人员应具备相关通信技能和知识，熟悉DSC设备的操作和功能，并持有有效的通信操作证书。

3.DSC操作应遵循以下原则：准确性、迅速性、简洁性、尊重他人和机构。

4.DSC设备应按照规定进行定期维护和检验，确保其正常工作。

二、装备准备1.操作人员应事先熟悉所使用的DSC设备的品牌、型号和功能，并确保设备处于正常工作状态。

2.确保设备的电源充足，如有需要，应随时准备备用电池或电源适配器。

3.确保设备的天线连接良好，没有任何杂音或干扰。

4.将设备放置在平稳的表面上，确保操作方便且不会滑动。

三、操作步骤1.打开DSC设备，等待设备启动完毕。

2.在设备界面上选择相应的操作模式（如呼叫、信息发送等）。

4.在输入框中填写要发送的信息内容，确保简洁明了。

5.确认输入无误后，点击发送按钮，等待对方的回复或响应。

6.如有需要，操作人员可以根据DSC设备的功能选择适当的操作选项，如呼叫特定频道、发送警报等。

7.操作完成后，及时关闭设备并做好相应的记录。

四、常见问题和应对方法1.无法开机或设备出现故障：检查设备的电源和连接是否正常，如有需要，更换电池或修理设备。

3.收到无关信息或骚扰信息：根据设备功能屏蔽或删除相关信息，并采取必要措施防止再次受到类似信息。

4.需要紧急报警或求助：根据设备功能选择相应的警报选项，并及时向相关机构报告和求助。

五、操作注意事项1.严禁使用DSC设备进行虚假报警或传播虚假信息，如有违反者，将依法追究其法律责任。

2.在操作DSC设备时应注意周围的通信环境，确保不会对其他通信系统造成干扰。

3.严禁擅自更改设备的设置或参数，如有需要，应在相关人员指导下进行操作。

DCS维护手册

前言很荣幸贵方选择高达科技提供的DCS系统，为保证系统的稳定运行，高达科技特提供本手册，请认真阅读本手册，以保证系统长期稳定运行。

本维护手册的主要内容有系统结构、SIEMENS硬件介绍、系统电路、日常维护和常见故障处理等几个部分。

在阅读过程中可能需要了解西门子PCS7的相关内容，可通过西门子的手册进行了解，手册可从西门子网站（）或高达科技网站()下载，也可向高达科技索取。

本手册不足之处，请批评指正。

目录系统结构 (1)DCS组成 (1)DCS系统结构图 (1)硬件介绍 (2)主控制器 (2)电源模块 (3)主控制器 (5)以太网模块 (8)ET 200M (8)IM153-1 (9)SM331 (9)SM332 (13)SM321 (14)SM322 (15)Profibus-DP (20)操作员站 (20)计算机 (21)UPS (21)操作系统 (22)系统软件 (22)TP/OP (22)系统电路 (22)柜内供电 (22)模拟量输入 (23)模拟量输出 (24)数字量输入 (25)数字量输出 (25)ES/OS站安装 (27)安装注意 (27)计算机恢复 (27)配置通讯 (29)控制级总线配置 (29)管理级总线配置 (30)通讯故障诊断 (31)控制级总线故障诊断 (31)管理级总线故障诊断 (32)下载 (33)下载硬件组态 (33)下载程序 (35)后记................................................................................................................. 错误！未定义书签。

系统结构DCS组成该项目DCS系统由高达科技设计制造，提供的主要设备有：1．控制柜个2．操作员站个（其中个兼作工程师站）3．UPS 个DCS系统结构图打浆控制室造纸控制室硬件介绍下面主要介绍DCS各部件的特点。

DCS系统操作维护说明

DCS系统操作维护说明DCS操作维护说明一、查询点通道位置：右键点击图上点---点详细---点名，SN站号、DN设备号、CN通道号二、控制器算法组态：1、进入：开始--程序--MACSV组态--选择工程名（JYKEQ1/JYKEQ2/JYKGY）--选择站号，进入控制器算法组态2、在线：点击“在线”--下拉菜单选择“登陆”，如果登陆不上去，点击“在线”--通讯参数，选择另外3个通讯IP尝试登陆，如全登陆不上，请检查I/O站DPU及网线。

3、强制点：在线状态下，双击点名，按F7按钮，强制点颜色变红。

如需取消强制点：在线状态下，双击变红点名，按F7按钮，恢复原色，强制恢复。

看管脚，如反馈、指令、开许可、自动开、关等。

注意：修改逻辑及点后需再次登陆，先编译再下装且只可无扰下装。

设备运行时不允许初始化下装，否则所有设备状态及指令清零。

三、修改通道：1、编辑数据库：程序--MACSV组态软件--进入数据库总控下拉菜单内选择工程名（JYKGY/JYKEQ2/JYKEQ1）--点击“编辑”--编辑数据库--点击“系统”--数据操作--选择需修改的点类型--点选“旧风格”进入数据库编辑文本窗口。

按照站号、设备号、通道号查找需修改的点，修改其点名、量程、报警等。

修改完成后，点击左上角菜单中第一个红色对号按钮即“更新数据库”，点击第二个红色对号按钮即“校验”，如校验后无错误信息，关闭数据库编辑文本窗口。

编辑数据库后在数据控总控窗口点击红色向下箭头，进行完全编译，待完全编译完成后自动生成下装文件。

2、下装：程序--MACSV组态软件--工程师在线下装--输入用户名及口令（eng0/eng1/eng2用户名与口令相同）--选择工程点击“系统命令”--“下装”--“服务器”--全选所有服务器--选择服务器IP（注意：此处需查看当前下装服务器是否为备用状态），勾选“下装后自动注销重启服务器”--直接下装下装完成后，待服务器网线恢复绿色状态，画面上点击“服务器切换”切换完成后，重复工程师下装操作，下装另外一台已切换为备用的服务器，最后，进入控制器算法组态逻辑，编译，在线登陆，检查修改点状态是否已修改完成。

DCS维护及工作说明

DCS维护及工作说明一、故障判断。

1、开关量故障判断。

开关量点可通过短接来判断DCS系统是否正确。

开关量输入点短接后DCS上会显示该点为一。

如果短接后该点不唯一则说明该点不正常。

开关量输出测点，先检测该测点上是否有电压，如果电压不正常先检测现场设备。

如电压正常，短接后相当于DCS发出该点的控制指令，如现场设备正常动作，而DCS控制无法完成则检查DCS指令发出时该点是否接通，如该点在发出指令时没有变化则说明该点不正常。

2、模拟量故障判断。

模拟量点可通过加标准信号来判断DCS系统是否正确。

在加标准信号时请注意接线方式。

如果信号电缆接地也会造成无法正确检测。

3、脉冲量故障判断。

脉冲量点可通过连续短接来判断DCS系统是否正确。

在连续短接时该点的检测量会出现变化。

如果如果没有变化，请检测电压是否正常。

如果电压正常而短接后没有变化则说明该点不正常。

二、DCS故障维护1、检查系统状态。

在操作员站画面上点击图象管理——系统状态图，检查系统网络状态是否正常。

点击I/O站，观察模块状态有无异常。

2、更换模块。

如果系统状态和该模块的状态都没有异常，则很有可能是该模块损坏，更换同一类型的模块进行试验，如果更换后正常则说明该模块的通道有损坏的现象。

更换模块前一定要进行通道电压的检查，以免损坏模块。

三、设备的修改及调试方法。

电动门、电动机、电磁阀的控制是通过HSSCS5模块完成的。

电动门的控制都已经做好了，但调试时，1、顺控调试。

电动门、电动机、电磁阀的控制是通过HSSCS5模块完成的。

电动门的控制都已经做好了，但调试时，理解HSSCS5的工作原理还是比较重要。

1，工作原理：HSSCS5输入端的“V1”连接的是“开反馈点”，“V2”连接的是“关反馈点”。

V1为TEUE，则画面上对应设备的“开状态”显示红色，V2为TEUE，则画面上对应设备的“关状态”显示绿色。

HSSCS5输出端的“DV”连接的是“开命令”，“RV”连接的是“关命令”。

“中远厦门”轮中高频DSC操作规程

MF/HF DSC-60操作规程1．DSC和无线电话工作模式设置1．1．打开电源开关POWER，此时屏幕显示DSC准备屏幕或无线1．2．按[1/RT/2182]键显示SSB无线电话设置屏幕，可操作SSB通信。

1．3．按[6/SCAN/MNO]键显示DSC准备屏幕；1．4．按[2/DSC/ABC]键，显示DSC呼叫电文输入屏幕；2．面板照明和屏幕对比度控制：按[9/☼]键，屏幕显示亮度和对比度控制菜单，旋转[ENT]键选择亮度控制DIMMER，按[ENT]键，再旋转[ENT]键，选择合适的亮度，按[ENT]键确认，再旋转[ENT]键选择对比度控制CONTRAST，按[ENT]键，再旋转[ENT]键，选择合适的对比度，按[ENT]键确认；3．按[7]键，出现“SOUND：OFF”，2秒后消失，扬声器关闭；再次按[7]键，出现“SOUND：ON”，2秒后消失，扬声器打开；4．按[6/SCAN]键可起动或停止DSC普通通信频率的扫描。

注意：DSC遇险频率的扫描是不能被停止的。

5．自动确认（ACKNOWLEDGE）的设置5．1．按[6/SCAM/MNO]键，显示DSC准备屏幕。

5．2．按[5/ACK]键，每按一次[5/ACK]键，过2秒后，在屏幕右上角替换出现“AUTO ACK”和“MANUAL”。

6．位置和时间设置6．1．在DSC准备屏幕上，按[#/SETUP]，显示“SETUP MENU”。

6．2．旋转[ENT]键选择“POSITION”按[ENT]键显示“POSITION SETUP”。

6．3．按[ENT]，打开“INPUT TYPE”菜单，旋转[ENT]键选“MANUAL”，再按[ENT]键确认。

6．4．旋转[ENT]键选择“Latitude”或“Longitude”按[ENT]键，然后输入相应数据，然后按[ENT]键确认。

6．5．旋转[ENT]键，选择“TIME”按[ENT]键打开输入窗口，输入UTC时间，按[ENT]确认。

DCS系统维护手册

一、DCS培训资料（一）、DCS系统结构图1.网络结构图1)50~57为本系统的8台操作员站，其中50为工程师站兼操作员站；2)A、B为本系统的服务器站，由51和52操作员站兼任；3)10#站为本系统的窑炉控制站；11#站为本系统的1、2通路控制站；12#站为本系统的3、4通路控制站；4)配置为冗余结构，服务器互为冗余、操作员站互为冗余、网络通讯线互为冗余、控制站主控单元互为冗余；2.机柜成套图见附录。

3.网络结构及设备示意图见附录。

1)服务器与控制站之间使用工业以太网协议；2)服务器与操作员站之间使用TCP/IP协议；3)现场控制站与远程I/O站及拉丝机控制柜之间使用Profibus DP总线；（二）、DCS系统设备状态灯含义1. FM801：主控单元2.FM148A：八路大信号模拟量输入模块3.FM148E：八通道隔离型模拟量输入模块4.FM151A：8路4~20mA模拟量输出模块5. FM161D：十六路触点型开关量输入模块…注‟面板上标号为1~ 16的16个指示灯，为通道指示灯，分别表示通道0~ 15的开关状态，“亮”表示该通道导通，“灭”表示该通道断开；6.FM171B：十六路晶体管开关量输出模块…注‟面板上标号为1~ 16的16个指示灯，为通道指示灯，分别表示通道0~ 15的开关状态，“亮”表示该通道导通，“灭”表示该通道断开；7.FM1201：DP 总线重复器模块…注‟DP1、DP2 闪烁的速率取决于总线上数据量的大小。

数据量越大，闪烁的速率越快；（三）、DCS系统模块接线说明此接线图适用于FM148A(FM148E、FM151A)+FM131A1. FM148A+FM131A2.FM148E+FM131A3. FM151A+FM131A4. FM161D+FM131A…注‟上图所示接线方法为双线干结点接法，由DCS单独配臵查询电源；针对本项目DI信号接线说明：24VDC+24VDC-继电器端子现场触点以下15路接线原理同对应通道接线详见接线表。

DCS系统维护检修操作规程

DCS系统维护检修操作规程DCS系统（分散控制系统）是一种广泛应用于工业控制领域的自动化控制系统，用于监控和控制工厂生产过程。

随着技术的发展，DCS系统的应用面日益广泛，公司对其维护检修操作规程是非常重要的。

下面是一份DCS系统维护检修操作规程，总计字数超过1200字。

一、维护检修操作规程的目的和范围1.目的：制定本规程的目的是为了确保DCS系统的可靠性和稳定性，保障生产过程的顺利进行。

2.范围：本规程适用于公司所有的DCS系统及其相关设备。

二、维护检修操作的条件和要求1.操作人员应具备相关的专业知识和技能，并经过相应的培训和考核合格。

2.操作人员应熟悉DCS系统的各项功能和配置，并了解相关的操作流程。

3.操作人员在进行维护检修操作前，应仔细研读相关的系统说明书和维护手册，并进行全面的系统检查。

三、维护检修操作的流程1.维护检修计划的制定：根据DCS系统的使用情况和维护需求，制定详细的维护检修计划，包括维护内容、维护时间和维护人员等信息。

2.维护设备的准备：根据维护计划，备齐所需的维护工具和设备，并确保其正常运行。

3.维护检修操作的执行：按照维护计划的要求，进行相应的维护检修操作，包括设备的清洁、调试和更换等。

4.维护记录的填写：在维护过程中，对所进行的维护检修操作进行详细的记录，包括维护时间、维护内容和维护结果等信息。

5.维护结果的评估：对维护检修操作的结果进行评估和分析，判断是否达到维护目标，并提出改进措施。

四、维护检修操作的注意事项1.操作人员在进行维护检修操作前，应确保设备的安全，断开电源并进行相关的防护措施。

2.操作人员要按照操作流程，有序地进行维护检修操作，避免操作失误和不必要的操作。

3.操作人员在进行维护检修操作时，要注意观察设备的运行情况，发现异常及时报告，避免发生故障和事故。

4.操作人员在进行维护检修操作后，要进行设备的功能测试，确保设备正常运行。

5.操作人员在维护检修过程中，要认真填写相关的维护记录，做到记录真实、准确和完整。

RC15xx DSC-60 产品说明书

RC15xxEQUIPMENT INSTALLATIONDSC-60 (Refer to Installation Manual, DSC-60)The DSC-60 DSC/Watch Receiver has been mounted and wired into the console.Only the antenna needs to be installed. A label is attached to the DSC-60 front panel to show whether it was setup for an active or passive antenna.This antenna connection is made to the D.ANT port. (Refer to Pg 7, Standard Wiring, of the Installation Manual for the correct antenna port location.)Passive Antenna1. When a passive antenna is used it must be impedance matched to 50 ohmcable, for connection to the DSC-60.2. If necessary, disassemble the DSC-60 and change the jumper on the RCVR boardfrom active to passive (see Pg 20, Preamp Settings, of the Installation Manual).3. When reinstalling the DSC-60 in the console, be sure to attach the cables to the correctports (see Pg 7, Standard Wiring, of the Installation Manual).Active Antenna1. Install the preamp (FAX-5 coupler). Connect a2.6m whip or 2 to 3 meter longwire to the preamp (see Pgs 3 and 4, Preamp Unit, of the Installation Manual).2. Ground the preamp to the mounting mast (see Pg 4 of the Installation Manual).3. If necessary disassemble the DSC-60 and change the jumper on the RCVR boardfrom passive to active (see Pg 20, Preamp Settings, of the Installation Manual).4. When reinstalling the DSC-60 in the console, be sure to attach the cables to the correctports (see Pg 7, Standard Wiring, of the Installation Manual).4-3。