C10-4DM(Manual_DM_series)日本神钢振动控制器手册

1. Introduction 1

2. Safety Instructions 2

3. Precautions for operation 5

4. Structure and Name of Part 6

5. Installation 7

6. Check and Adjustment of Resonance point 8

7. Trouble Shooting 9

8. Readjustment 10

9. Specifications 11 10. Outline Drawing 12 11. Guarantee

13

The version C (DM-**C) prartsfeeder drive unit has a connector for power supply .

Instruction Manual for Dual Motion Partsfeed er

Model DM-30C, -38C, -45C

Before operating your dual motion partsfeeder , you and/or any other operator shall read and follow the safety instructions carefully to operate the equipment correctly , properly and safely . Then the instructions save you from any accident and/or injury and/or, any damage and/or loss of your property . The safety instructions are classified by the degree of injury and damage such as “Danger”, “W arning”, “Caution” and “Request”.

■ Please keep the instruction manual on file as any operator is able to read and refer to it.

■ When you transfer or rent the equipment to the other you are required to submit the instruction

manual, coming to the user’s attention, along with the equipment. The user shall operate the equipment correctly , properly and safely .

■ Those Safety instructions do not necessarily cover all danger , accident and/or damage. Please

always follow the safety instructions and act the safety first attitude.

● Do not use the equipment in an environment where inflammable gases exist. The equipment has

no explosion-proof structure and then the use should cause an explosion or a fire.

● The equipment must be installed firmly on a rigid base to avoid an accidental injury by toppling

down, falling and/or abnormal running of it.

● Do not sprinkle the equipment with thinner, organic solvent, water , oil and oil products. It may

cause any injury by abnormal running, getting a shock and a fire.

● Cut off the power , first of all, with a safety disconnect switch supplied by you before wiring,

cleaning and maintaining the equipment.

● Do not operate the equipment in any vacuum chamber .

-Please surely read this instruction manual- 2. Safety Instructions .

● Do not operate the equipment over the specifications agreed upon. The operation over the

specifications must result in damage, malfunction and/or short lifetime of it.

● Do not climb up on and/or put something heavy on the equipment to avoid an accidental injury by

toppling and/or falling down, and/or damage and/or abnormal running of the equipment.

● Do not damage the power cable and wirings to the equipment, such as abrasion of coating and

over bending, tensioning, coiling down, loading heavy weight on and/or pinching wires. The damage of a cable causes leakage and/or mal-conduction, which leads to a fire, getting workers shocked and/or abnormal running of the equipment.

● Wire the equipment correctly and properly consulting this instruction manual. Any wrong wiring

leads to abnormal running and/or breakdown.

● Inspect and make sure the wiring before turning on the power .

● The ground line must be connected on the ground terminal in the controller . The equipment must

be operated with ground without fail.

● Do not connect or disconnect connecters while the power is turning on. Do not stress the connecter

carelessly otherwise workers should be injured or get shocked and the equipment must be damaged.

● Keep sufficient maintenance space around the equipment. Small space makes the maintenance

work difficult and poor maintenance must damage the equipment

● Install the equipment in a clean and dry room. It has no dust-tight structure.

● n the case of carrying a equipment, lift it with its mounting base or the stand on which the

equipment is installed. Do not pull and lift it with the power cable.

● Install the equipment on a horizontal rigid frame or stand. The mounting base of the equipment

should be bolted on the frame. In the case of a weak frame, vibration of the equipment may spread into it and

cause resonance of the frame. The resonance affects the vibration of the equipment being mal-functioned.

● If you provide a weak bowl on the equipment the work pieces must be jumping on the both end of

the bowl.

● The equipment must provide a genuine controller to the model.

-Continued-

Warning

● Keep clearance around the equipment and avoid the bowl or drive unit to hit against any object.

Hitting against any object results insufficient stroke of the equipment and clattering noise.

● Do not get the surface of the bowl dirty with oil, moisture, dust etc. The dirty bowl cannot handle

work pieces.

● Stop running at once when you hear any clattering noise or humming of the equipment. Check

and remove the cause of the noise. Running without maintenance must cause severe and non-restored damage on the equipment.

● Any operator should wear safety shoes and work gloves to handle a equipment.

● Y ou have to pay attention and take safety measures such as enough allowance to the specifications

and the rating, and/or a fail-safe system, when you want to use the equipment in unspecified environment and/or circumstance by the specifications agreed upon otherwise the use of the equipment may endanger any person or property .

● Where the equipment becomes out of order and/or disused, it should be an industrial waste subject

to local regulation.

● Install the equipment on a horizontal rigid frame or stand free from heat, dust, humidity ,

condensation or freezing.

● In case the work pieces are charged or magnetized, poor feeding rate or miss-orientation will occur.

Look and analyze the troubled phenomenon exactly and take proper countermeasure.

● The bowl must be designed so that the moment of inertia about the center axe, along the conveying

direction, of the bowl must be symmetrical on the moving frame of the equipment. Un-symmetry results insufficient stroke. Y ou have to pay attention to the length, weight, rigidity and moment of inertia of the bowl.

● Where you would manufacture and tool the bowl and attachments it would break the symmetry

about mass or moment of inertia

of the bowl.

The un-symmetry slows down

or fluctuate the conveying speed of work pieces. Y ou should attach small pieces of weight on the bowl to balance and symmetrize the mass and moment.

The product of SINFONIA TECHNOLOGY has been fully balanced and symmetrized in the shop.